JCB SMALL PLATFORM SKID STEER AND COMPACT TRACK LOADERS

Transcription

1 JC SMALL PLATFORM SKID STEER AND COMPACT TRACK LOADERS RATED OPERATING CAPACITY: 135 1,350 b (612 kg) 155 1,550 b (703 kg) 175 1,750 b (794 kg) 190 1,900 b (862 kg) 205 2,050 b (930 kg) I M J G F E D L P C N K H A O * Iustration represents vertica ift machine. Specs in charts refect changes in machines due to ift path. STATIC DIMENSIONS 135 / 155 / 175 / 190 / 205 Machine Modes ft-in (m) ft-in (m) ft-in (m) ft-in (m) ft-in (m) A Overa Length 11-5 (3.49) 11-5 (3.49) 11-7 (3.53) 11-8 (3.56) (3.61) Whee ase 3-6 (1.07) 3-6 (1.07) 3-6 (1.07) 3-6 (1.07) 3-6 (1.07) C Ange of Departure degrees D Overa Height 6-6 (1.98) 6-6 (1.98) 6-6 (1.98) 6-6 (1.98) 6-6 (1.98) E Dump Height 7-5 (2.26) 7-5 (2.26) 7-5 (2.26) 7-5 (2.26) 7-5 (2.26) F Loadover Height 9-4 (2.84) 9-4 (2.84) 9-4 (2.84) 9-4 (2.84) 9-4 (2.84) G Height to Hinge Pin Fuy Raised 9-10 (3.00) 9-10 (3.00) 9-10 (3.00) 9-10 (3.00) 9-10 (3.00) H Ground Leve (cutting edge) 3-3 (1.00) 3-3 (1.00) 3-3 (1.00) 3-3 (1.00) 3-3 (1.00) I Max Fu Height 3-0 (.91) 3-0 (.91) 3-2 (.97) 3-3 (.99) 3-5 (1.04) J Fu Height - Fuy Dumped 1-10 (.56) 1-10 (.56) 2-9 (.86) 2-9 (.86) 2-9 (.86) K Dig Depth (toe pate horizonta) Cearance in (mm) -0.4 (-10) -0.4 (-10) -0.4 (-10) -0.4 (-10) -0.4 (-10) L Ground degrees Machine Modes ft-in (m) ft-in (m) ft-in (m) ft-in (m) ft-in (m) M Dump Ange degrees N ucket Width - Standard 5-0 (1.52) 5-5 (1.68) 5-5 (1.68) 5-8 (1.73) 6-0 (1.83) ucket Width - Optiona 4-6 (1.37) 5-0 (1.52) 5-8 (1.73) 6-0 (1.83) 5-8 (1.68) O Width Over Tires - Standard 4-11 (1.52) 5-3 (1.60) 5-3 (1.60) 5-3 (1.60) 5-3 (1.60) Width Over Tires - Optiona 4-5 (1.37) 5-0 (1.52) 5-0 (1.52) 5-0 (1.52) 5-0 (1.52) Rated Operating Capacity b SAE (kg) 1350 (612.3) 1550 (703.1) 1750 (793.8) 1900 (861.8) 2050 (929.9) ucket Capacity - Standard yd³ (m³).47 (.36).52 (.40).52 (.40).53 (.41).57 (.44) Turning Radius ucket Corner Radius 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) Quick Hitch Radius 3-7 (1.10) 3-7 (1.10) 3-9 (1.14) 3-9 (1.14) 3-9 (1.14) Rear Chassis Radius 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) P Ground Cearance in (mm) 8.3 (210) 8.3 (210) 8.3 (210) 8.3 (210) 8.3 (210) Lift Path Radia Radia Vertica Vertica Vertica

2 JC SMALL PLATFORM SKID STEER AND COMPACT TRACK LOADERS RATED OPERATING CAPACITY: 150T 1,500 b (681 kg) 190T 1,900 b (862 kg) 205T 2,050 b (930 kg) I M J G F E D L P C N K H A O * Iustration represents vertica ift machine. Specs in charts refect changes in machines due to ift path. STATIC DIMENSIONS 150T / 190T / 205T Machine Modes 150T 190T 205T ft-in (m) ft-in (m) ft-in (m) A Overa Length 11-5 (3.49) 11-7 (3.53) 11-9 (3.58) Track ase 5-10 (1.78) 5-10 (1.78) 5-10 (1.78) C Ange of Departure degrees D Overa Height 6-7 (2.00) 6-7 (2.00) 6-7 (2.00) E Dump Height 7-6 (2.29) 7-6 (2.29) 7-6 (2.29) F Loadover Height 9-4 (2.85) 9-4 (2.85) 9-4 (2.85) G Height to Hinge Pin Fuy Raised 9-11 (3.02) 9-11 (3.02) 9-11 (3.02) H Ground Leve 3-7 (1.09) 3-3 (1.00) 3-3 (1.00) I Max Fu Height 3-3 (0.99) 4-0 (1.21) 4-0 (1.21) J Fu Height - Fuy Dumped 2-1 (0.64) 2-9 (0.85) 2-9 (0.85) K Dig Depth Cearance in (mm) -0.4 (-10) -0.4 (-10) -0.4 (-10) L Ground degrees M Dump Ange degrees Machine Modes 150T 190T 205T ft-in (m) ft-in (m) ft-in (m) N ucket Width - Standard 5-8 (1.73) 5-8 (1.73) 6-0 (1.83) ucket Width - Optiona 5-6 (1.68) 6-0 (1.83) 5-8 (1.73) O Width Over Tracks - Standard 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) Width Over Tracks - Optiona 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) Rated Operating Capacity b SAE (kg) 1500 (680.4) 1900 (861.8) 2050 (929.9) ucket Capacity - Standard yd³ (m³).53 (.41).53 (.41).57 (.44) Turning Radius ucket Corner Radius 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) Quick Hitch Radius 3-9 (1.10) 3-9 (1.14) 3-9 (1.14) Rear Chassis Radius 5-5 (1.65) 5-5 (1.65) 5-5 (1.65) P Ground Cearance in (mm) 9.1 (230) 9.1 (230) 9.1 (230) Ground earing Pressure* psi (Kp) 6.75 (46.6) 6.20 (42.6) 6.50 (44.5) Lift Path Radia Vertica Vertica * with 12.6 wide tracks (320 mm)

3 JC LARGE PLATFORM SKID STEER AND COMPACT TRACK LOADERS RATED OPERATING CAPACITY: 225 2,250 b (1,021 kg) 260 2,600 b (1,179 kg) 280 2,800 b (1,270 kg) 300 3,000 b (1,361 kg) 330 3,295 b (1,495 kg) I M J G F E D L P C O N K H A * Iustration represents vertica ift machine. Specs in charts refect changes in machines due to ift path. STATIC DIMENSIONS 225 / 260 / 280 / 300 / 330 Machine Modes ft-in (m) ft-in (m) ft-in (m) ft-in (m) ft-in (m) A Overa Length 12-2 (3.69) 12-2 (3.69) 12-4 (3.76) 12-5 (3.78) 12-7 (3.80) Whee ase 4-0 (1.22) 4-0 (1.22) 4-0 (1.22) 4-0 (1.22) 4-0 (1.22) C Ange of Departure degrees D Overa Height 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) 6-10 (2.09) 6-11 (2.11) E Dump Height 8-1 (2.46) 8-1 (2.46) 8-1 (2.46) 8-1 (2.46) 8-2 (2.49) F Loadover Height 9-10 (3.02) 9-10 (3.02) 9-10 (3.02) 9-10 (3.02) 10 (3.05) G Height to Hinge Pin Fuy Raised 10-5 (3.175) 10-5 (3.175) 10-5 (3.175) 10-5 (3.175) 10-6 (3.2) H Ground Leve (0.98) (0.98) (0.98) 3-5 (1.04) 3-5 (1.04) I Max Fu Height 3-2 (.96) (1.23) (1.23) (1.23) 3-11 (1.2) J Fu Height - Fuy Dumped 1-11 (.59) 2-10 (0.87) 2-10 (0.87) 2-11 (0.90) 2-11 (0.90) K Dig Depth (toe pate horizonta) Cearance in (mm) -3/8 (-10) -3/8 (-10) -3/8 (-10) -3/8 (-10) 0 L Ground degrees Machine Modes ft-in (m) ft-in (m) ft-in (m) ft-in (m) ft-in (m) M Dump Ange degrees N ucket Width - Standard 6-0 (1.82) 6-0 (1.82) 6-0 (1.82) 6-0 (1.82) 6-6 (1.98) O Width Over Tires - Standard 6-0 (1.82) 6-0 (1.82) 6-0 (1.82) 6-0 (1.82) 6-2 (1.87) Width Over Tires - Optiona 6-2 (1.87) 6-2 (1.87) 6-2 (1.87) 6-2 (1.87) 6-0 (1.82) Rated Operating Capacity 50% b (kg) 2250 (1021) 2600 (1179) 2800 (1270) 3000 (1361) 3295 (1495) ucket Capacity - Standard yd³ (m³).62 (.47).62 (.47).62 (.47).67 (.51).67 (.51) Turning Radius ucket Corner Radius 7-3 (2.20) 7-3 (2.20) 7-3 (2.20) 7-3 (2.20) 7-3 (2.20) Quick Hitch Radius (1.48) (1.48) (1.48) (1.48) (1.48) Rear Chassis Radius (1.76) (1.76) (1.76) (1.76) (1.76) P Ground Cearance in (mm) 9.4 (238) 9.4 (238) 9.4 (238) 9.4 (238) 9.8 (248) Lift Path Radia Vertica Vertica Vertica Vertica

4 JC LARGE PLATFORM SKID STEER AND COMPACT TRACK LOADERS RATED OPERATING CAPACITY: 225T 2,250 b (1,021 kg) 260T 2,600 b (1,179 kg) 300T 3,000 b (1,361 kg) 320T 3,200 b (1,452 kg) I M J G F E D L P C O H N K A * Iustration represents vertica ift machine. Specs in charts refect changes in machines due to ift path. STATIC DIMENSIONS 225T / 260T / 300T / 320T Machine Modes 225T 260T 300T 320T ft-in (m) ft-in (m) ft-in (m) ft-in (m) A Overa Length 12-2 (3.69) 12-2 (3.69) 12-5 (3.78) 12-5 (3.78) Track ase 6-11 (2.1) 6-11 (2.1) 6-11 (2.1) 6-11 (2.1) C Ange of Departure degrees D Overa Height 6-10 (2.08) 6-10 (2.08) 6-10 (2.08) 6-10 (2.08) E Dump Height 7-11 (2.42) 7-11 (2.42) 7-10 (2.39) 7-10 (2.39) F Loadover Height 9-10 (2.99) 9-10 (2.99) 9-10 (2.99) 9-10 (2.99) G Height to Hinge Pin Fuy Raised 10-5 (3.18) 10-5 (3.18) 10-5 (3.18) 10-5 (3.18) H Ground Leve 3-2 (0.96) 3-2 (0.96) 3-5 (1.04) 3-5 (1.04) I Max Fu Height 3-1 (.935) 4 (1.21) 4.3 (1.30) 4.3 (1.30) J Fu Height - Fuy Dumped 1-11 (.585) (0.87) 2-11 (0.90) 2-11 (0.90) K Dig Depth Cearance in (mm) -3/8 (-10) -3/8 (-10) -3/8 (-10) -3/8 (-10) L Ground degrees Machine Modes 225T 260T 300T 320T ft-in (m) ft-in (m) ft-in (m) ft-in (m) M Dump Ange degrees N ucket Width - Standard 6-6 (1.98) 6-6 (1.98) 7-0 (2.13) 7-0 (2.13) O Width Over Tracks - Standard 6-1 (1.85) 6-6 (1.98) 6-6 (1.98) 6-6 (1.98) Rated Operating Capacity 35% b (kg) 2250 (1021) 2600 (1179) 3000 (1361) 3200 (1452) Rated Operating Capacity 50% b (kg) 3214 (1458) 3994 (1812) 4314 (1957) 4573 (2074) ucket Capacity - Standard yd³ (m³).79 (.59).79 (.59).84 (.64).84 (.64) Turning Radius ucket Corner Radius (2.24) (2.24) (2.24) (2.24) Quick Hitch Radius (1.48) (1.48) (1.48) (1.48) Rear Chassis Radius 5.95 (1.76) 5.95 (1.76) 5.95 (1.76) 5.95 (1.76) P Ground Cearance in (mm) 9.8 (248) 9.8 (248) 9.8 (248) 9.8 (248) Ground earing Pressure* psi (Kp) 4.36 (30.1) 4.6 (31.7) 4.8 (33.1) 4.9 (33.8) Lift Path Radia Vertica Vertica Vertica * with 17.7 wide tracks (450 mm)

5 JC SKID STEER AND COMPACT TRACK LOADERS HYDRAULIC PERFORMANCE - SMALL PLATFORM Mode R.O.C. b (kg) Tipping Load b (kg) Loader Lift b (kg) ucket Tit b (kg) (612) 2989 (1356) 3175 (1440) 4012 (1820) (703) 3100 (1406) 3902 (1770) 4012 (1820) (794) 3500 (1587) 3461 (1570) 4718 (2140) (862) 3800 (1723) 3461 (1570) 4718 (2140) (930) 4100 (1859) 3461 (1570) 4718 (2140) 150T 1500 (680) 4334 (1966) 3902 (1770) 4012 (1820) 190T 1900 (862) 5429 (2462) 3461 (1570) 4718 (2140) 205T 2050 (930) 5857 (2656) 3461 (1570) 4718 (2140) HYDRAULIC PERFORMANCE - LARGE PLATFORM Mode R.O.C. b (kg) Tipping Load b (kg) Loader Lift b (kg) ucket Tit b (kg) (1021) 4908 (2226) 5884 (2669) 5699 (2585) (1179) 5448 (2471) 5884 (2669) 5699 (2585) (1270) 5608 (2543) 5884 (2669) 5699 (2585) (1361) 6024 (2732) 5809 (2634) 7187 (3260) (1495) 6590 (2989) 5809 (2634) 7187 (3260) 225 T 2250 (1021) 6428 (2915) 5884 (2669) 5699 (2585) 260 T 2600 (1179) 7991 (3624) 5809 (2634) 7187 (3260) 300 T 3000 (1361) 8628 (3913) 5809 (2634) 7187 (3260) 320 T 3200 (1452) 9145 (4148) 5809 (2634) 7187 (3260) HYDRAULICS - SMALL PLATFORM In addition to the main hydrostatic drive pumps, there is a dedicated oader and attachments suppy pump (auxiiary hydrauics circuit standard on a base modes). High fow is optiona on a modes except the 135. Pump Fow: 18.5 gpm ( rpm engine speed Main reief pressure 3335 psi (230 bar) HYD HP Low Fow (36.0)* HYD HP High Fow (51.4)* *cacuated Low ever efforts give exceent and easy contro of transmission oader and attachments. Auxiiary hydrauics are actuated via the right hand controer giving progressive contro of oi fow for precise attachment contro (eft hand controer ocation on opriona 7 way muti-function joysticks. Loader arm hydrauic ines under protective stee guard on Poweroom. Canister stye, fu fow, hydrauic oi fiter. JC engine oi for engine and chain case. JC hydrauic oi. The optiona High Fow circuit provides 26.4 ga/min (100 iters/min) pump fow to the front of the machine for operation of high capacity attachments such as trenchers and cod paners. Separate hydrauic pump for transmission charge and hydrauic fan. HYDRAULICS - LARGE PLATFORM In addition to the main hydrostatic drive pumps, there is a dedicated oader and attachments suppy pump (auxiiary hydrauics circuit standard on a base modes). Pump Fow: 24 gpm ( rpm engine speed Main reief pressure 3335 psi (230 bar) HYD HP Low Fow (46.7)* HYD HP High Fow (64.2)* *cacuated Low ever efforts give exceent and easy contro of transmission oader and attachments. Auxiiary hydrauics are actuated via the right hand controer giving progressive contro of oi fow for precise attachment contro. Loader arm hydrauic ines under protective stee guard on Poweroom. Canister stye, fu fow, hydrauic oi fiter. JC engine oi for engine and chain case. JC hydrauic oi. The optiona High Fow circuit provides 33 ga/min (125 iters/min) pump fow to the front of the machine for operation of high capacity attachments such as trenchers and cod paners. Separate hydrauic pump for transmission charge and hydrauic fan. CAPACITIES - SMALL PLATFORM ga () Hydrauic System (incuding tank) 11.1 (42) Fue Tank 25.9 (98) Engine Cooant 4.0 (15) Engine Oi 2.6 (10) LH Chaincase (wheeed machines ony) 2.0 (7.6) RH Chaincase (wheeed machines ony) 2.0 (7.6) CAPACITIES - LARGE PLATFORM ga () Hydrauic System (incuding tank) 15.9 (60) Fue Tank 27.2 (103) Engine Cooant 4.1 (15.5) Engine Oi 3.7 (14) LH Chaincase (wheeed machines ony) 3.1 (11.7) RH Chaincase (wheeed machines ony) 3.1 (11.7)

6 JC SKID STEER AND COMPACT TRACK LOADERS Mode ENGINE - SMALL PLATFORM /175/150T 190/205/190T/205T Koher KDI 1903 TCR Koher KDI 1903 TCR Koher KDI 2504 TCR Dispacement in 3 (cm 3 ) (1,860) (1,860) (2,481) Fue Diese Diese Diese Cooing Liquid Liquid Liquid Aspiration Turbo Turbo Turbo Gross 2800 rpm SAE J1995 hp (kw) 48 (36) 56 (42) 62 (46) Gross 1200 rpm SAE J1995 b/ft (Nm) (225) (225) (300) Starter Motor hp (kw) 2.72 (2) 2.72 (2) 2.72 (2) attery V/Ah 12/109 12/109 12/109 Aternator amps Emission Certification EPA-T4F (EU St3) EPA-T4F(EU St3) EPA-T4F(EU St3) Engine Oi Service Interva Hours Variabe Speed Hydrauicay Driven Fan YES YES YES Mode ENGINE - LARGE PLATFORM 225/260/280/225T/260T/300/330/300T/320T EcoMAX TCAE-55 Dispacement in 3 (cm 3 ) 268 (4399) Fue Diese Cooing Water Aspiration Turbo Gross 2400 rpm SAE J1995 hp (kw) 74 (55) Gross 1200 rpm SAE J1995 b/ft (Nm) 295 (400) Starter Motor hp (kw) 5.63 (4.2) attery V/Ah 12 / 109 Aternator amps 95 Emission Certification EPA-T4F (EU St3) Engine Oi Service Interva Hours 500 Variabe Speed Hydrauicay Driven Fan YES TRANSMISSION - SMALL PLATFORM A fu servo controed hydrostatic transmission giving zero to maximum speed, both forward and reverse at fu power. Independent transmission systems for both the eft and right side, controed through servo contros for both precise and easy operation. Transmission power system maintains fu engine power avaiabiity maximizing oader and attachment contro. Mode Singe Speed Two Speed mph (km/h) mph (km/h) / mph (km/h) Trave Speeds 135: 7.5 (12.0) N/A Trave Speeds 155/175/190/205: 7.5 (12.0) 5.6 (9.0) / 11.5 (18.5) Trave Speeds 150T/190T/205T: 6.2 (10.0) 5.6 (9.0) / 7.8 (12.6) TRANSMISSION - LARGE PLATFORM A fu servo controed hydrostatic transmission giving zero to maximum speed, both forward and reverse at fu power. Independent transmission systems for both the eft and right side, controed through servo contros for both precise and easy operation. Transmission power system maintains fu engine power avaiabiity maximizing oader and attachment contro. Mode Singe Speed Two Speed mph (km/h) mph (km/h) / mph (km/h) Trave Speeds 225/260/280/300: 6.8 (10.9) 6.8 (10.9) / 12.4 (20) Trave Speeds 330: 7.3 (11.7) 7.3 (11.7) / 13.5 (21.7) Trave Speeds 225T/260T/300T/320T: 5.7 (9.2) 4.8 (7.7) / 7.8 (12.6) SMALL PLATFORM LARGE PLATFORM TIRES TRACKS TIRES TRACKS Standard 135/ x PR Standard Track Fotation Standard 175/190/ x 16.5 x 8 PR Wide Track Fotation Avaiabe Options Standard Track - Wide Track Lifemaster Industria Pneumatic 31.5 / 13 x 16.5 Extra Foatation rawer Soid Industria Foatation tires are fitted for most appications. A Track Modes 12.6 in (320 mm) traction ug Standard 225/260/280/ x PR Standard x 17.5 x 10 PR Avaiabe Options Standard Track - Wide Track Lifemaster Industria Pneumatic 33 / 15.5 x 16.5 Extra Foatation rawer Soid Industria Foatation tires are fitted for most appications. 225T/260T 12.6 in (320 mm) traction ug 17.7 in (450 mm) traction ug 300T/320T 17.7 in (450 mm) traction ug *For arduous conditions and hostie environments soid tires are recommended. *For arduous conditions and hostie environments soid tires are recommended.

7 JC SKID STEER AND COMPACT TRACK LOADERS WEIGHT - SMALL PLATFORM SAE Operating Weight Fuy operationa with quickhitch, standard shove, fu fue tank, open canopy b (75 kg) operator: b (2791 kg) b (3200 kg) 150T 8137 b (3691 kg) b (2883 kg) b (3310 kg) 190T 8355 b (3790 kg) b (3050 kg) 205T 8734 b (3962 kg) LIGHTING AND ELECTRICS - SMALL PLATFORM 12 V, negative ground system 1,000 cod cranking amp (CCA) battery amp aternator Cab mounted instrument pane with ignition, fue gauge, hour meter, 155 and Above 100 amp aternator and eectronic throtte Aso incorporated into the instrument pane, is a warning ight custer which aso has audibe aarms for: Low charge pressure ocked air fiter Engine water temperature Engine oi pressure Hydrauic oi pressure Aternator Cab mounted fuse and reay box designed to keep dirt and water out; IP 69 externa connections; standard battery isoater. STANDARD EQUIPMENT - ALL MODELS Isoation mounted canopy. ROPS and FOPS. Fu audibe and visua warning systems. Restraint activated safety system. Loader arm safety strut. Centrifuga dry type engine air fiter with safety eement. Mechanica quickhitch. Eectronic hand throtte. Two front and one rear workight. Emergency ower vave. Fue gauge. Hydrauic park brake. Standard Fow auxiary hydrauics. Three way joysticks. Rear service access door. Titing cab. Static seat in wheeed. Mechanica suspension in tracked. Foat. Pod storage area. Cup hoder. Power socket. Rear view mirror. Interior ight. attery isoator. OPERATOR VISIILITY VISILE AREAS OSTRUCTED AREAS JC s unique Poweroom design makes our Skid Steer the word s safest and provides unmatched visibiity. WEIGHT - LARGE PLATFORM SAE Operating Weight Fuy operationa with quickhitch, standard shove, fu fue tank, open canopy b (75 kg) operator: b (3608 kg) b (4107 kg) 225T 10,216 b (4634 kg) b (3734 kg) b (4243 kg) 260T 10,756 b (4879 kg) b (3796 kg) 300T 11,287 b (5120 kg) 320T 11,596 b (5260 kg) OPTIONAL EQUIPMENT - ALL MODELS Seaed and pressurized cab with heater/defroster. Air conditioning (155 and above). Mechanica and air suspension seats. Road ights. eacon. Foot throtte. Fire extinguisher. Tookit. Sef eveing. Leve 2 FOPS guard. Heavy-duty rear door guard. Front screen guard. High Fow auxiiary hydrauics (155 and above). Spark arrestor. Tooth guard. Powered quickhitch. Smooth Ride System (155 and above). Lexan screen. Radio. Twine cutter (wheeed units ony). Three inch seat bet. Creep speed. 1S0/H pattern changeover. Fenders. Reversing fan. Pre-ceaner. OPERATOR ENVIRONMENT Fu ROPS and Leve 1 FOPS with optiona Leve 2 FOPS guard for demoition, fu audio and visua warning system. Soundproofing gives noise eves compying with EC reguations. Cab access through side door due to JC s Poweroom design. Deuxe environment avaiabe in either open canopy, cab with heat, or cab with heat and A/C (155 and Above) Unequaed a-around visibiity. Fuy adjustabe seat. LIGHTING AND ELECTRICS - LARGE PLATFORM 12 V, negative ground system 1,000 cod cranking amp (CCA) battery 95 amp aternator Cab mounted instrument pane with ignition, fue gauge, hour meter, and eectronic throtte Aso incorporated into the instrument pane, is a warning ight custer which aso has audibe aarms for: Low charge pressure ocked air fiter Engine water temperature Engine oi pressure Hydrauic oi pressure Aternator Cab mounted fuse and reay box designed to keep dirt and water out; IP 69 externa connections; standard battery isoater. Retractabe seat bet fitted as standard. Drainage cover for easy drainage of cab. Fu servo contro with either standard (3 way) joysticks or optiona JC muti-function (7-way) joysticks. CONTROLS JC 270 o Visibiity Typica Skid Steer 165 o Visibiity JC servo contro (ISO) pattern, provides a drive functions on eft and oader function on right joystick. The eft hand contro pod pivots rearwards, providing unparaeed machine entry / exit.

8 JC SKID STEER AND COMPACT TRACK LOADERS ATTACHMENTS Attachment Description Attachment Description Augers Panetary drive augers are buit with fabricated boring heads using Forks, Manure Provides exceent visibiity whie moving oose hay and manure. 1/2 thick pates with 5/8 carriage bots and nuts. Forestry Cutting Heads Low profie with patent pending roter design, rotor operates at ae Spear Utiized for picking up and carrying round baes of hay rpm. reakers JC hammers are among the most efficient avaiabe and are Grappes, rush Heavy-duty unit with open bottom and sides which aows machine to perfecty matched to JC equipment. carry objects onger than unit width. rooms, Sweeper Coector For genera sweeping duties around the job site. Grappes, Scrap Heavy-duty unit with twin ram grappe and ram guard protection. rooms, Ange JC ange brooms cover many appications incuding site cean-up, Rakes, Auto JC auto rake is used to groom and finish soi for sod or seed. andscape and ground maintenance, road work, and repair. Rakes, Landscape Power JC andscape rakes are exceent toos for ceaning up debris, rush Cutters For remova of brush and sma trees up to 4 in diameter. maintaining roads, driveways, and finish grading. uckets, 6-in-1 Mutipurpose Genuine JC 6-in-1 buckets are idea for mutipe appications such as Rakes, Landscape Preparators One soution for genera cean-up, rock remova, and soi preparation. digging, oading, dozing, grading, spreading, and grabbing. Rock Saws Avaiabe in 48 or 60 diameter for cutting rock and other hard surfaces. uckets, Dirt / Genera Purpose Genuine JC dirt / genera purpose buckets are recommended where Siage Defacers Open design aows operator to see bucket face and keeps the maximum breakout performance is required. attachment cog free. uckets, Landscape Genuine JC andscape buckets are idea when cutting edge visibiity Snow owers Provides exceent visibiity with 25 to 36 shroud opening. is important. Snow ades Avaiabe in various widths for removing snow. uckets, Light Materia Genuine JC ight materia buckets are speciay designed for ower Stump Grinders Provides an environmentay friendy way to safey remove density materias such as snow, much, and grain. tree stumps. uckets, Snow High carbon stee bucket with swept top wrap to better contain materia. Tiers Provides for safe and efficient tiing with choice of 4 or 6 tiing depths. Cod Paners The JC cod paner is a vauabe too for parking ot and street repairs in Tree Spades Provides safe and efficient remova and panting of trees. addition to many other uses. Trenchers The JC trencher is usefu for trenching footings, burying utiities, instaing Dozer ades The JC dozer bade is an attachment that is suited for genera grading irrigation systems, etc. and and cearing appications. Vibratory Roers Used to compact sand, grave, sois, crushed stone, and other aggregates. Forks, Paet Paet forks are used in a variety of genera forkift appications such as construction, industria, and agricutura industries.

9 JC SKID STEER AND COMPACT TRACK LOADERS A GLOAL COMMITMENT TO QUALITY JC s tota commitment to its products and customers has heped it grow from a one-man business into one of the word s argest manufacturers of backhoe oaders, crawer excavators, wheeed excavators, teescopic handers, wheeed oaders, dump trucks, rough terrain fork ifts, industria fork ifts, mini/midi excavators, skid steer oaders and tractors. y making constant and massive investments in the atest production technoogy, the JC factories have become some of the most advanced in the word. y eading the fied in innovative research and design, extensive testing and stringent quaity contro, JC machines have become renowned a over the word for performance, vaue and reiabiity. And with an extensive deaer saes and service network in over 150 countries, we aim to deiver the best customer support in the industry. Through setting the standards by which others are judged, JC has become one of the word s most impressive success stories. JC Headquarters Savannah, 2000 amford vd, Savannah, GA Te: (912) Fax: (912) JC reserves the right to change design, materias and/or specifications without notice. Specifications are appicabe to units sod in the United States and Canada. The JC ogo is a registered trademark of J C amford Excavators Ltd. DWUSA /13