Maintenance & Modifications

Transcription

1 Maintenance & Modifications - Reduce MMO costs with 30% Quick guide for selection, sizing and ordering of EIT & HVAC support systems Flexible cold work solutions Quick and Easy On-site modifications Light weight support system Reduce deferment & installation cost

2 We Support You! This is your tool for selection, sizing and ordering of EI&T support systems used in offshore maintenance and modification work. By following the step-by-step guide you can reduce your MMO costs with 30%. Full product overview is found at oglaend-system.com/selector STEP-BY-STEP GUIDE TO REDUCING PROJECT COSTS WITH 30% ENGINEERING PURCHASE INSTALLATION Identify total load (cables, tubing, HVAC and more). Define starter points. Select support system. Select parts for cable ladders/ cable trays/hvac support. All our systems for EI&T are pre-engineered. Calculations and documentation are completed by using the Mekano loading table below. Call us for support - we have done this since Order using the procedure described at the back of the brochure or produce a MTO/BOM through company purchase procedures. Call us for support Define Starters Select Support Systems Select Cable Ladders, Cable Trays & HVAC Lift cables by using lifting straps. Re-use or install new starters. Install the support typicals (few parts). Install the cable ladder, tray and HVAC Redline original or project drawings. Ready for asbuilt of DFO. SUPPORT SYSTEM INSTALLATION GUIDELINES Our systems are pre-engineered. The need for further calculations in PMO projects will in most cases be unnecessary. System segregation distance: 0.3 m Distance between supports: Ladder < 5 m, Tray < 3 m Maximum distance to bend or raiser: 0.6 m Spare 20% Fill all slots at connection points with bolts (minimum two bolts per connection point) Static Vertical Load Mekano Loading Table U-Support: vertical Channel Length 1000 mm Mekano CH100-2T2 (vertical & horizontal) Mekano CH50-2T1,5 (vertical) & CH100-1 (horizontal) Horizontal Channel Length

3 MEKANO SUPPORT SYSTEM Compared to UNO, the Mekano system is 43% More cost efficient 22% Quicker to install 30% Lighter 22% Stronger 5. FASTNERS Qty/ pack M6x M6x M6x M10x M10x MEKANO CHANNELS H BEAM CLAMP 50 H BEAM CLAMP 100 BOLTED L-BRACKET CH CH50-2T5 CH100-2T mm lengths. Fixing Clamps Beam Clamp* Beam Clamp** For flange thickness up to 14 mm. * flange width mm ** flange width mm Fixing Clamps Beam Clamp Angle Bracket For flange width 100 to 350 mm and up to 30 mm thick. Angle Brackets can be used to reinforce connections. 5. Bolted Starter* Bolted Starter** * For CH 50-2T5 ** For CH 100-2T HVAC & CANTILEVER CANTILIVER ARM Art. no denotes the size of cable tray the cantiliver arm is intended for. Diameter HVAC CLAMP Art.no

4 OE100 CABLE LADDER SYSTEM CABLE LADDER FLAT ELBOW 90º FLEXI RISER FLEXI RISER PART mm lengths, also available in 6000 mm length 4 x M10x20 fasteners included Any required angle from 0-90º Any required angle from 0-90º SPLICE CONNECTOR Standard With notches x M10x20 fasteners included DIVIDER Straight Flat Elbow Flexi Riser * x M6x12 fasteners included *Made to fit both inside and outside risers HINGE Vertical * 0.7 Horizontal x M10x20 fasteners included *Adjustment in steps of 4º FIXING CLAMPS Inside Outside Twisted (pairs) * (4*) x M10x20 fasteners included. REDUCER PART END PROTECTION Standard COVER 150* * * ** x M10x20 fasteners included 750** ** * 3000 mm length ** 1500 mm length

5 CROSS PIECE x M10x20 fasteners included TEE PIECE 150/ / / / / / R=600 mm 6 x M10x20 fasteners included COVER CLIP Standard Raised END COVER BRACKETS 40/ / / This poster shows the main/most used parts of the OE100 System. Visit our website for a full overview of the OE System. Certificates: Please contact us for exact application.

6 SPB-RF40 CABLE TRAY SYSTEM CABLE TRAY FLAT ELBOW 90 FLEXI RISER SPLICE CONNECTOR SC-IN SC-OU x M6x12 fasteners included mm length 4 x M6x12 fasteners included Allows free vertical angle, bending by hand FLAT ELBOW R=75 mm 4 x M6x12 fasteners included TEE PIECE Z REDUCER COVER CLIP ELBOW FLEXI R=75 mm 6 x M6x12 fasteners included x M6x12 fasteners included Standard * 0.02 Raised *Use 4 pieces per 3 m cover Any required angle from 0-90º

7 COVER COMBI RISER mm length 4 x M6x12 fasteners included SPLICE PLATE SPB SC 85x TAG PLATE x M6x12 fasteners included TAG TAG x M6x12 fasteners included This poster shows the main/most used parts of the SPB-RF40 System. Visit our website for a full overview of the SPB System. Certificates: Please contact us for exact application.

8 UNO SUPPORT SYSTEM H BEAM CLAMP UNO CHANNELS D-87-A Perforated base For attaching UNO Channel to H beam flange sections. Square U-Bolt included. Must be fitted in pairs. 7. Un-perforated base mm lengths. BOLTED STARTER UNO PARTS E FASTNERS Qty/pack Square Washer hole plate L-Bracket Tee Bracket Angle Bracket M10x30 bolt Wing Fitting M10 nut End Cap ORDERING Scan QR code with your mobile phone or go to Add order including art. no. and quantity Save order form and send it to ordre@oglaend-system.com Order using mobile phone Alternativelly, send your order directly as an to ordre@oglaend-system.com Oglaend System Phone: oglaend@oglaend-system.com Norway Sweden Denmark Holland UK Dubai Korea Singapore Malaysia Russia USA China Australia