Drill and Boring Bits, Adapters

Transcription

1 rill and Boring Bits, Adapters

2 Hinge Boring Bit T.C. Z2+V R R R Two raker teeth, centre point and two inserted spurs. Right-hand rotation. For drilling of accurate holes for hinges in hardwood and various kinds of wood composites on portable routers. For hard, brittle synthetic coating we recoend No

3 Hinge Boring Bit T.C. Z interchangeable shank design R R M R M 12 x R For drilling of accurate holes for hinges on portable routers. Two raker teeth, centre point, with ground side bevel. Cutting angle geometry designed for speed up to R.P.M. Right-hand rotation. 2.2

4 Hinge Boring Bit with interchangeable T.C. tip interchangeable shank design M 12 x R Spare parts / Accessories Interch. T.C. tip for = R 1 Interch. T.C. tip for = R 1 Torx countersunk screw M 4 x 8, T R 10 / With 1 straight interchangeable T.C. tip with centre point, chip guiding step and side bevels. For drilling of tear-free holes and hinge holes on portable routers up to R.P.M. PU 2.3

5 Slot Bit T.C.T. for FESTO - OMINO IG M 6 x 0, R IG M 6 x 0, R IG M 6 x 0, R IG M 6 x 0, R IG = internal thread Two cutting edges with ground side bevel, without centre point. with internal thread and clamping flat. Right-hand rotation. For use on FESTO-OMINO-joining machines. Oscillating routing of long holes for omino-dowels. 2.4

6 owel rill T.C.T. for Mafell ,5 8 x R ,5 8 x R ,5 8 x R x R x R 16* 30 58/65 8 x R * Only on 40P For drilling of blind-holes in solid wood, various wood composites and boards etc. on MAFELL-uo dowel machines 40G and 40P, as well as on portable routers. Centre point and two cutting edges with side bevel. Cutting geometry designed for high spindle speeds. Spiral part Teflon-coated. Parallel shank with clamping flat and length adjusting screw. Right-hand rotation. 2.5

7 iamond (PC) owel rills for blind holes Z2 L2 L4 L ,6 2,6 2,6 2,6 3,2 3,2 57,5 57, x x x x x x L R L R L R for through holes Z1 L2 L4 L1 Z ,5 4,5 4,5 4,5 6,5 6,5 57,5 57, x x x x x x L R L R L R for through holes Z2 L2 L4 L ,4 6,4 8,6 9,5 9, x x x x x L R R L R No : Two PC cutting edges with double bevel. No : Z1 with V-point and with double bevel. No : Z2 with V-point and with double bevel. with clamping flat and adjusting screw. For drilling of accurate blind-holes or through-holes in extremely abrasive materials, e.g. MF, HF etc., fire resistant chipboard and MF-board or gypsum plaster boards. For use on automatic dowel hole machines or CNC machines. No / in < 8 and No : Not applicable for particularly dense workpiece material (e.g. Corian, Trespa, etc.) 2.6

8 Twist rill for load-bearing bolts T.C / x 30* R x R x R Solid T.C. head with two cutting edges, centre point and negatively ground spurs. Spiral portion Teflon-coated. With landed flute. Right-hand rotation. For drilling accurate blind-holes for hinges with load-bearing bolts. * With clamping flat For other diameters see pages 2.15/

9 Solid T.C. Twist rill for fastening holes ,5 10 x R x R / Spiral portion in solid T.C. with V-point 120. Parallel shank with clamping flat and length adjusting screw. Right-hand rotation. For drilling fastening holes for face plates, striking plates, and mounting plates for floor sealings on CNC machines. 2.8

10 Twist rill - solid T.C coon shank and drilling diameter L R 2, L 2, R L R L R 3, L 3, R 3, L 3, R L R L R L R L R / V-point, coon shank and drilling diameter. For use in adaptor bushes Nos /

11 Boring Pin - Solid T.C. BP Round tool body with special grade solid T.C. with one parallel flute and tapered point. = 2,5 to 4 with coon shank and clamping diameter, to be used in conjunction with adaptor No or with brazed shank 10, with clamping flat and length adjusting screw. From = 5 upwards brazed into shank 10. Can be used for either right-hand or left-hand rotation. Besonders geeignet für Sacklöcher in abrasiv wirkenden Werkstoffen, auch mit mineralischen Bestandteilen. Auch für trockene Massivhölzer einsetzbar. Einsatz auf übellochbohrautomaten oder CNC-Maschinen. ie Anzahl der Bohrstifte, die zusaen in einem Bohrgetriebe eingesetzt werden können, hängt von der Leistungsfähigkeit der Maschine ab. Coon shank and drilling diameter 1 ) 2, , , , , , , , , , , , , , , ,5 4, , = 57,5 2, ,5 10 x , ,5 10 x , ,5 10 x , ,5 10 x , ,5 10 x , ,5 10 x , ,5 10 x , = 70 2, x , x , x , x , x , x , x Extremely long tool life which could only be achieved with diamond drills! Applicable for R.-H. and L.-H. rotation! Large regrinding area, modest regrinding costs! 1) * To be used with adaptors No ( see page 2.51). Spare parts / Accessories Length adjusting screw Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.10

12 owel rill - Solid T.C. Solid T.C. spiral protion with flat centre point, shaped by the point angle and two negative ground, strengthened spurs. Enlarged flutes. Parallel shank with clamping flat and length adjusting screw. For use in adaptor chucks etc. on dowel hole boring machines and CNC machines. To drill blind-holes in solid wood, various kinds of wood composites and boards etc., as well as in plastic laminated materials parallel shank 10 Overall length 57,5 2, x L 2, x R x L x R 3, x L 3, x R x L x R x L x R x L x R Overall length x L x R 3, x L 3, x R x L x R x L x R x L x R Spare parts / Accessories with flat point Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU Essential improvement of the tool life achieved through more wear resistant T.C. grade Little vibration stress through rigid solid T.C. design No break-outs when retracting the drill through non-stepped parallel spiral portion Maximum concentricity Regrinding area considerably increased 2.11

13 ISOUR owel rills T.C.T. Solid T.C. head with flat centre point shaped by the point angle and two negatively ground spurs. Enlarged flutes. Spiral portion Teflon-coated for reduced friction and better chip flow. Parallel shank with clamping flat and length adjusting screw. Tool life further increased compared with No , by optimizing the T.C. grade, the grinding quality, as well as the geometry of the cutting edges. For use in adaptor chucks, etc. on dowel hole boring machines and CNC machines to drill blind-holes in solid wood, various kinds of wood composites and boards etc. also in plastic laminated materials parallel shank 10 Overall length 57, x L x R x L x R x L x R x L x R Overall length x L x R x L x R x L x R x L x R x L x R x L x R Overall length x L x R x L x R Spare parts / Accessories with flat point Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU Considerably increased tool life compared with traditional T.C. dowel drills Set-up times can be enormously reduced for only a small extra costs 2.12

14 owel rill T.C.T parallel shank 10 Overall length 57, x L x R 4, x L 4, x R x L x R 5, x L 5, x R 5, x R x L x R 6, x L 6, x R x L x R 8, x L 8, x R x R x L x R 10, x L 10, x R x L x R x R 12, x L 12, x R Overall length 70 without landed flute x L x R 4, x L 4, x R x L x R 5, x L 5, x R 5, x R 5, x L 5, x R x L x R 6, x R 6, x L 6, x R 6, x L 6, x R x L x R 7, x L 7, x R x L x R 8, x L 8, x R 8, x L 8, x R 8, x L 8, x R x L x R 9, x L 9, x R x L x R 10, x L 2.13

15 10, x R 10, x R x L x R x L x R 12, x L 12, x R Overall length x L x R x L x R x L x R x L x R x L x R Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiral portion Teflon-coated for reduced friction and better chip flow. Parallel shank with clamping flat and length adjusting screw. For use in adaptor chucks, etc. on dowel hole boring machines and CNC machines to drill blind-holes in solid wood, various kinds of wood composites and boards etc., as well as in plastic laminated materials. Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.14

16 owel rills T.C.T. with landed flute parallel shank 10 Overall length 57, x L x R x L x R x L x R x L x R x L x R x L x R x R Overall length x L x R 5, x L 5, x R x L x R 7, x R x L x R 8, x R x L x R x L x R x L x R 12, x R x L x R x L x R x L x R x L x R Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiral portion Teflon-coated, with landed flute. Parallel shank with clamping flat and length adjusting screw. No without length adjusting screw. The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of the countersink directly on the spiral portion of the drill. For use in adaptor chucks, etc. on dowel hole boring machines and CNC machines to drill blind-holes in solid wood, various kinds of wood composites and boards etc., as well as in plastic laminated materials. Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R parallel shank 10 Overall length x L x R x L x R x L x R x L x R PU 2.15

17 x L x R x L x R Overall length x L x R x L x R 6, x R x L x R 7, x R x L x R 8, x R x R x L x R x R x L x 30* R x L x R Overall length 110/130 ** x L x R 14 ** x L 14 ** x R 16 ** x R 2.16

18 owel rills HSS parallel shank 10 Overall length L R L R L R Two cutting edges with spurs and centre point. Parallel shank, without length adjusting screw. No : Spiral portion with landed flute. No : Spiral portion without (with *) landed flute. For use in adaptor chucks, etc. on dowel hole boring machines or CNC machines. For drilling accurate blind-holes in soft and hardwood parallel shank 10 Overall length x R x L x R 2.17

19 owel rill T.C.T. with landed flute parallel shank 8 Overall length 55, x L x R x L x R x L x R x L x R x L x R x R Overall length x R x L x R x L x R x L x R x L x R x R Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiral portion Teflon-coated, with landed flute. Parallel shank with clamping flat and length adjusting screw. The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of the countersink directly on the spiral portion of the drill. For use in adaptor chucks etc. on dowel hole drilling machines and CNC machines, to drill blind-holes in solid wood, various kinds of wood composites and boards etc., as well as in plastic laminated materials. Spare parts / Accessories Allen screw R 10 PU 2.18

20 owel rill T.C.T parallel shank 10 Overall length 57, x L x R x L x R x L x R 5, x R x L x R x L x R x L x R Overall length x L x R 3, x R x L x R 4, x L 4, x R x L x R 5, x L 5, x R x L x R 6, x L 6, x R x L x R 7, x R x L x R 8, x L 8, x R x R 9, x R x L x R x L x R x L x R Overall length 77 for through holes x L x R x L x R 6, x R x L x R x L x R 8, x R x L x R x L x R x L x R x L x R 2.19

21 60 V-point of solid T.C. Ø 3 and 3,5 with solid T.C. spiral portion and 120 V-point. Parallel shank with clamping flat and length adjusting screw. Spiral portion Teflon-coated up from Ø 4. For drilling through-holes in different kinds of wood composites and boards on various dowel hole boring machines (automatic boring machines, CNC machines, etc.). Ø 3 and 3,5 can also be used to drill blind-holes. Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.20

22 owel rill T.C.T. for through holes parallel shank 8 - with landed flute Overall length 55, x L x R x L x R Overall length x L x R x R 60 V-point of solid T.C. Parallel shank with clamping flat and length adjusting screw. Spiral portion with landed flute, Teflon-coated for reduced friction and better chip flow. The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of the countersink directly on the spiral portion of the drill. For drilling through-holes in various kinds of wood composites and boards on automatic dowel hole boring machines and CNC machines. 2.21

23 owel rill T.C.T. for through holes parallel shank 10 - with landed flute Overall length 57, x L x R Overall length x L x R x L x R * escription see page V-point of solid T.C. Parallel shank with clamping flat and length adjusting screw. Spiral portion with landed flute, Teflon-coated for reduced friction and better chip flow. The landed flute (heel) provides improved centering on return stroke and permits infinitely variable mounting of the countersink directly on the spiral portion of the drill. For drilling through-holes in various kinds of wood composites and boards on automatic dowel hole boring machines and CNC machines. Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.22

24 owel rill - Solid T.C. for through holes parallel shank 10 Overall length 57,5 L ,3 10 x L ,3 10 x R ,9 10 x L ,9 10 x R Overall length ,3 10 x L ,3 10 x R ,9 10 x L ,9 10 x R ,7 10 x L ,7 10 x R Solid T.C. spiral portion, with V-point 60. Parallel shank with clamping flat and length adjusting screw. For drilling through-holes in solid wood, various kinds of wood composites and boards on automatic dowel holes drilling machines and CNC-machines. Especially recoended for drilling GFK, CFK, HPL (e.g. Trespa) and all coon kinds of wood composites. Increased tool life through wear resistant T.C. grade Little vibration stress through rigid solid T.C. design No break-outs when retracting the drill through non-stepped parallel spiral portion Finest ground spiral portion for improved chip flow Considerably increased regrinding area data R.P.M. = min -1 v f = 0,5-4 m/min Reduce R.P.M. and feed rate for difficult ranges of materials (R.P.M. = m min -1 and v f = 0,5-1 m min -1 ). To increase the tool life and to improve the chip flow an add. JSO-X coating is possible. See page. Price on request. 2.23

25 ISOUR owel rill T.C.T. for through holes parallel shank 10 Overall length 57, x L x R x L x R Overall length x L x R x L x R x L x R x L x R x L x R x L x R Overall length x L x R x L x R Solid special grade T.C. head, with V-point and double bevel. Spiral portion Teflon-coated for reduced friction and better chip flow. Parallel shank with clamping flat and length adjusting screw. For drilling through-holes in different kinds of wood composites and boards on dowel hole drilling machines and CNC machines. Considerably increased tool life compared with traditional T.C. dowel drills Set-up times can be enormously reduced for only small extra costs Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.24

26 owel rills with threaded shank T.C.T external thread M 8 rilling depth 45 L L R L R L R external thread M 8 - with register 9 x 4 rilling depth 40 L L R rilling depth L R external thread M 10 rilling depth 45 L L R L R L R L R rilling depth L R L R L R external thread M 10 - V-point 60 L L R No /30705/30710/30720 Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle. Spiral portion Teflon-coated. (No /30710/30720). For drilling accurate blind-holes and through-holes (No ) in various kinds of wood composites and boards. No V-point of solid T.C. Spiral portion Teflon-coated. 2.25

27 2.26

28 owel rills T.C.T external thread M 10 - with register 11 x 4 L L R R L R L R shank 6 - for Schleicher machines x R /10 x R Solid T.C. head with two cutting edges and centre point. Negatively ground spurs and increased back relief. Spiral portion Teflon-coated. No : spiral portion with landed flute. Parallel shank with clamping flat, up from = 8 with additional collar = 10. For drilling accurate blind-holes in solid wood and wood composites and boards. 2.27

29 owel rills T.C.T. internal thread M centre point and spurs L R R L R R V-point L R No Solid T.C. head with two cutting edges, with centre point and negatively ground spurs and increased back relief angle (same as No ). Spiral portion Teflon-coated. For drilling accurate blind-holes (No ) and through-holes (No ) in wood composites and boards. 2.28

30 Hinge Boring Bits T.C.T. Z2+V Two T.C.T. cutting edges, two inserted spurs and centre point. Parallel shank with clamping flat and length adjusting screw. iamond (PC) hinge boring bits see type on page. For drilling accurate and clean-cut blind-holes in hardwood, various kinds of wood composites and boards etc. (for furniture fittings etc.). No : With reduced centre point. To drill blind-holes for hinges close to the lower surface layer. Overall length 57, ,5 10 x L 15 55,5 10 x R 18 55,5 10 x L 18 55,5 10 x R 20 55,5 10 x L 20 55,5 10 x R 22 55,5 10 x R 25 55,5 10 x L 25 55,5 10 x R 26 55,5 10 x R 30 55,5 10 x R 34 55,5 10 x R 35 55,5 10 x L 35 55,5 10 x R 40 55,5 10 x R Overall length x L x R x L x R x L x R x R x L x R x L x R x R x L x R Overall length x R Special design for through-holes see page with reduced centre point Overall length x L x R x L x R x R Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.29

31 Hinge Boring Bits T.C.T. Z3+V /30330 With centre point 25 55,5 57,5 10 x L 35 55,5 57,5 10 x L 35 55,5 57,5 10 x R Without centre point 25 55,5-10 x L 25 55,5-10 x R 26 55,5-10 x R 35 55,5-10 x R 38 55,5-10 x L * escription on page No with three cutting edges, three inserted spurs and centre point. No with three cutting edges, three inserted spurs, without centre point. Both with parallel shank and length adjusting screw. For drilling accurate and clean cut blind-holes in hardwood, various kinds of wood composites and boards etc. (for furniture fittings etc.), on hinge boring machines, drilling machines or on CNC machines. Spare parts / Accessories Length adjusting screw R 10 Length adjusting screw M 5 x 17, special design* R 10 PU 2.30

32 Hinge Boring Bit Set T.C.T. for ouble-head hinges Type Rotation 30 57,5 A rh./lh 10 x ,5 A rh./lh 10 x ,5 B rh./lh 10 x Single drills 30 57,5 A right 30 57,5 A left 34 57,5 A right 34 57,5 A left 34 57,5 B right 34 57,5 B left 10 x x x x x x R L R L R L Set consisting of 1 pc each left-hand and right-hand T.C.T. hinge boring bit. Two cutting edges, two inserted spurs and centre point. Parallel shank with clamping flat and length adjusting screw. For drilling precise, blind-holes for double-head hinges (e.g. GU-JET-T-SOLO), as well as for corner fittings and scissor fittings in wooden windows on the following corner fitting drilling machines. Type A: for Striffler, Ganner, Götzinger, Hess, Schafberger a. Sprödhuber, etc. machines. Type B: for Weinig-Unirex, Weinig-Conturex, Koch machines. 2.31

33 Hinge Boring Bits with threaded shank T.C.T. Z2+V external thread M R R Two T.C.T. cutting edges, two inserted spurs and centre point. For drilling accurate and clean cut blind-holes in hardwood, various kinds of wood composites and boards, etc. (for furniture fittings etc.). 2.32

34 Hinge Boring Bit with reversible T.C. tips Z2+V ,5 57,5 10 x R 30 55,5 57,5 10 x R 35 55,5 57,5 10 x R x R x R x L x R Two reversible T.C. raker tips and two reversible spurs. Adjustable centre point for drilling depths close to lower surface layer if necessary. Raker tips fixed with counter sunk screws for perfect chip removal. with clamping flat and length adjusting screw. For drilling accurate and clean cut blind-holes in all coon board materials, soft- and hardwood (e.g. for furniture fittings). * With chip breaking grooves for reduced feed force available on request. Without disturbing clamping screws in the chip space and therefore barrier free chip flow Ouick and easy unimpeded tip change 2.33

35 Cylinder Boring Bit T.C.T. Z2+V2 short design x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R x R Two cutting edges and centre point. Up to Ø 13 with spurs on plunge tips, from Ø 14 with two inserted spurs. Parallel shank. Right-hand rotation. For drilling accurate holes in hardwood, various kinds of wood composites and boards, compressed wood, etc. 2.34

36 Cylinder Boring Bit T.C.T. Z2+V2 long design parallel shank x R x R x R x R x R x R x R x R x R x R Special peak design for through-holes on page 2.34 Two cutting edges, two inserted spurs, centre point. Parallel shank. Right-hand rotation. For drilling accurate holes in hardwood, various kinds of wood composites and boards, compressed wood etc. 2.35

37 Twist rill HS 30130/30132 coon shank and drilling diameter L R 2, L 2, R L R 3, L 3, R L R 4, L 4, R L R 5, R L R 6, R R 7, R L R 8, R R R Extra length R R R R R With centre point and spurs. Particularly large flutes for better chip removal. Special coating for improved life time and against rust. For drilling accurate blind-holes and through-holes in soft and hardwood. Solid tungsten carbide design see No (page 2.9). 2.36

38 Twist rill T.C.T. with landed flute coon shank and drilling diameter L R R R L R Extra length R 4, R R 5, R R 6, R R R 8, R R R R R Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Increased back relief angle (ill. on page 2.38). Spiral portion Teflon coated, with landed flute.* * The landed flute (heel) provides improved centering on return stroke and permits infinitely mounting of countersinks directly on the spiral portion of the drill. Especially recoended for drilling accurate blind-holes and through-holes in all kinds of wood, wood composites and boards, due to landed flute. Please also see No (page 2.9) for = 5 below. 2.37

39 Twist rill T.C.T. with landed flute parallel shank 13/16 x x R x R x R x R x R x R x R x R x R x R Solid T.C. head with centre point, two cutting edges and negatively ground spurs. Inceased back relief angle. Spiral portion Teflon-coated, with landed flute. The landed flute (heel) provides improved centering on return stroke and permits infinitely mounting of the countersink directly on the spiral portion of the drill. Especially recoended for drilling accurate blind-holes and through-holes in all kinds of wood, wood composites and boards, due to landed flute vibration-free running. 2.38

40 Twist rill - Solid T.C. with landed flute parallel shank L , x L , x R , x L , x R , x L , x R , x L , x R Solid T.C., two raker edges, two spurs, extra long centre point. Polished flutes for perfect chip removal, with JSO-Xcoating for improved life time. Parallel shank with clamping flat for use in Weldon clamping chucks. For drilling very deep and exceptionally accurate holes without emptying between. Especially applicable to drilling connection- and dowel holes in frame- and window production. Also perfect for drilling holes in oblique work-pieces. For soft and hardwood, glued wood as well as for wood in window production. In long-grain and end-grain. data: R.P.M = v f = 2-3 m/min It is necessary to determine the optimum feed rate within the specific range, depending on the material to be worked on. 2.39

41 Stockade rill HS with landed flute parallel shank L , x R , x R , x R , x R , x R , x R , x R , x R Two cutting edges, two spurs and extra long centre point. Spiral portion with landed flute. Stepped parallel shank 13 x 50. Right-hand rotation. For drilling holes in oblique work-pieces, e.g. holes for stockades in stair production. To be used with jigs or drilling attachments for stockade holes. For hardwood or exotic wood please use T.C. design No for longer tool life. 2.40

42 Countersink Z2 with parallel shank T.C.T. d x L x R 3, x R x L x R 4, x L 4, x R x L x R 5, x R x L x R Two cutting edges. Countersink angle 90. Parallel shank 10 x 30. To be used in conjunction with parallel shank twist drills No page 2.36, No page and No page

43 Countersink solid T.C. Z Angle L , R , R ,5 10* R * R R , R : Three solid T.C. edges, precise centre point on bottom. Right-hand rotation. * With clamping flat and length adjusting screw For countersinking of pre-drilled holes. Can also be used as decorative groove and bevelling cutter. 2.42

44 Loose Countersink T.C.T. Z d 3 15,5 16, R 4 15,5 16, L 4 15,5 16, R 5 15,5 16, L 5 15,5 16, R 6 15,5 16, L 6 15,5 16, R 7 15,5 16, L 7 15,5 16, R 8 15,5 16, L 8 15,5 16, R 9 15,5 16, R , L , R , R / Two T.C.T. cutting edges, countersink angle 90. To be used in conjunction with twist drills and dowel drills with landed flute Nos /30530/ 30150/ 30140/ 30145/ 30500/ To be clamped directly onto the spiral portion of the drill. Spare parts / Accessories Allen screw R 10 PU 2.43

45 Loose Countersink T.C.T. Z for shank clamping d For drills diameter 10 15,5 16, L 10 15,5 16, R , L , R / Two T.C.T. cutting edges, countersink angle 90. To be clamped onto the extended shank of drills No (page 2.13). Spare parts / Accessories Allen screw M 6 x 4 ISO 4029 (for = 15,5/20 ) R 10 Allen screw M 6 x 5 ISO 4029 (for = 22 ) R 10 PU 2.44

46 Copying Cutter HS (HSS-E) Z1 for working aluminium or plastics L 3 Form A R R R R R R Form B R R R R One helical HS cutting edge. Cutting on bottom and periphery. Type B with narrow neck. Right-hand rotation. For grooving, slotting and aperture operations in aluminium and plastic materials. For use on copying machines, e.g. Elumatec, Haffner, Rotox, Striffler, Wegoma, etc. 2.45

47 Water Slot Cutters HS (HSS-E) 25217/25218 helical design Z R R R 25220/25221 straight design Z With V-point R No /25218: helical design with either one or two cutting edges. No /25221: straight design, with one cutting edge. No : with V-point. Right-hand rotation. For use on copying and water slot machines, e.g. Elumatec, Haffner, Rotox, Striffler, Wegoma, etc. No especially recoendable for extrusions in plastics (PVC). 2.46

48 Quick-Change Adaptors rill holder d EL 10 17,8 17, Machine adaptors d Ill. No. 1 a Machine 10 22,5 Nottmeyer (former design) R 10 22,5 Nottmeyer (former design) L Ill. No Brema, Nottmeyer (new design) R Brema, Nottmeyer (new design) L Ill. No ,5 Ayen, Holzma, Mayer, Torwegge, etc R 10 22,5 Ayen, Holzma, Mayer, Torwegge, etc L Ill. No ,5 Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc R 10 22,5 Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc L Ill. No Scheer R Scheer L / Two-piece design, consisting of machine adaptor and drill holder, providing a system for quick changing of boring bits, adaptable to a variety of different spindle nose designs. Two clamping screws. Spare parts / Accessories Lubricating grease in tin Socket spanner for machine adaptor Allen screw R 10 Allen key SW 2,5, hexagon Plastic protection cap for d = Plastic protection cap for d = PU 2.47

49 Adaptors d Ill. No. 1 a Machine = Ill. No Nottmeyer (former design) R Nottmeyer (former design) L Ill. No Brema, Nottmeyer (new design) R Brema, Nottmeyer (new design) L Brema, Nottmeyer (new design) R Brema, Nottmeyer (new design) L Brema, Nottmeyer (new design) R Brema, Nottmeyer (new design) L Ill. No Ayen, Biesse, Holzma, Mayer, Torwegge, etc R Ayen, Biesse, Holzma, Mayer, Torwegge, etc L Ayen, Biesse, Holzma, Mayer, Torwegge, etc R Ayen, Biesse, Holzma, Mayer, Torwegge, etc L Ill. No Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc R Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc L Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc R Biesse, Busellato, Morbidelli, Torwegge, Weeke, etc L Ill. No ,5 Bilek, type K and N R ,5 Bilek, type K and N L Ill. No ,3 Alberti, Balestrini, Bilek, Schleicher, Vitap, etc R ,3 Alberti, Balestrini, Bilek, Schleicher, Vitap, etc L Ill. No Scheer R Scheer L / esigned as an adaptor chuck between spindle nose and drill shank. Two clamping screws. = 19 (d = 10 ), resp. = 15,5 (d = 8 ). Spare parts / Accessories Allen screw R 10 Allen key PU 2.48

50 Quick-Change Adaptor JSOFIX d ,5 M R ,5 M L ,5 M R ,5 M L ,5 M R ,5 M L Retention mechanism with sliding sleeve and magnet-assisted clamping. For keyless changing of drilling tools with 10 shank diameter, clamping flat and standard length adjusting screw. Chuck without built-in drilling tools must be covered against pollution with optional available dust protection bolts. Specific advantages: Insertion assisted by magnetism Powerful but short stroke of the sliding sleeve Improved concentricity Smooth running Special length adjusting screw not necessary Please ask for our special JSOFIX leaflet. 2.49

51 Quick-Change Adaptors d For Weeke, Ill. No , For Biesse, Ill. No R L For Grass, Ill. No Spare parts / Accessories Allen screw M 6 x 5 ISO 4029 (for Weeke/Grass) R 10 Allen screw M 6 x 6 ISO 4029 (for Biesse) R 10 Allen key PU 2.50

52 Bushings for Twist rills Split adaptor bush d , , Adaptor bush with parallel shank d x , x x x , x x x / To take twist drill No and boring pin No (page 2.10). with clamping flat, without length adjusting screw. Can be used for either right-hand or left-hand rotation. Spare parts / Accessories Allen screw R 10 Allen key PU 2.51