TRAFFIC SPEED TAPER LENGTH (L) 125' 190' 276' 328' 525' 600' 663' 25 MPH 30 MPH 35 MPH 40 MPH 45 MPH 50 MPH 55 MPH
|
|
|
- Aleesha Johnson
- 5 years ago
- Views:
Transcription
1
2 GENERL NOTE:. These distances are guidelines only. ctual distances will be determined on an individual basis by the ity. efe any wk may be started in the street area: 1. traffic control plan shall be submitted to, and then approved by the ity Engineer. 2. igns and delineation shall be in place, inspected and approved by a Public Wks Inspect.. uring construction: 1. copy of the approved traffic control plan shall be kept on the job site at all times. 2. ll wkers in the street area shall wear NI lass III safety apparel. 3. Flaggers shall be used as required. 4. ll traffic control and devices shall comply with the altrans Traffic Manual / MUT. FIGURE NOTE: 1. ll signs and traffic control devices shall confm to the MUT and LTRN tandards. 2. ll cones shall be 18" higher. ones used f night wk shall be 28" higher and reflectized by a 6" band located 3" to 4" from the top of the cone and an additional 4" band located 2" below the 6" band. 3. peeds on advisy plate to be determined by the ity Engineer. 4. Tempary parking sign(s) must be placed a minimum of 30 hours in advance of wk when parking removal is required to maintain a 10' minimum travel lane. ontact ity of an Luis Obispo Police epartment at f verification. 5. Use flashing arrow sign on roadways with three lanes me in speed zones of 35 MPH greater, when required in approved Traffic ontrol Plan. Use high level warning device in speed zones of less than 35 MPH. single flashing arrow sign (f each direction of travel) may be used in place of flashing beacons. 6. Flashing arrow sign (F) shall be Type I per ec of the current altrans tandard pecifications. Operate F in equential arrow mode. 7. "EN RO WORK" sign, as appropriate, shall be placed at the end of the wk zone. 8. ll warning signs f night lane closure shall be illuminated reflectized. ll advance warning signs shall be supplemented with flashing beacons during night lane closures. 9. Provide access f all driveways. 10. Where signalized intersections are affected, provide notice to ity Traffic ignal Maintenance Technician. 11. When construction signage is placed in a open bike lane, a 4' minimum lane f bicycle usage shall be maintained. If 4' minimum is unobtainable, signage shall be pole mounted. Y MH FIGURE LEGEN (PGE 2-17) Traffic one elineat ign (shown facing left) Flashing rrow ign High Level Warning evice (Flag Tree) Ptable Flashing eacon (Night Wk) irection of Travel (Not a Pavement Marking) Manhole Flagger Maintenance Vehicle w/ Flashing Lights Type II arricade Type III arricade Longitudinal hannelizing evice HRT (ll Figures) MINIMUM ELINETOR N IGN PLEMENT TRFFI PEE 25 MPH 30 MPH 35 MPH 40 MPH 45 MPH 50 MPH 55 MPH TPER LENGTH (L) 125' 190' 276' 328' 525' 600' 663' ELINETOR PING (Taper)* 26' 33' 39' 43' 46' 53' 59' (Tangent) IGN PING () (dvance of Taper) *12' TNR LNE WITH FOR LULTION PURPOE. WIER LNE REQUIRE ITIONL LENGTH 53' 66' 79' 85' 92' 105' 118' 100' 100' 100' 100' 328' 328' 328' UFFER PE () 155' 200' 250' 305' 360' 425' 495' REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 1
3 FIGURE TWO-LNE WORK IN ENTER OF ROWY Optional Flasher Vehicle ividing Line enterline R4-7 (R7) Install tempary No Parking signs (if required) ee Note 4 R4-7 (R7) 10' min.* 10' min.* Taper L Install tempary No Parking signs (if required) ee Note 4 Taper L ee hart "" lternative arricaded ee hart "" Wk Zone 24" x 18" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 2
4 FIGURE TWO-LNE ONE WY LOURE WITH FLGGER Indicate Nth W20-7a (9) IE TREET W3-4 (36) R1-1 (R1) W20-7a W3-4 (9) (36) ee hart "" ee hart "" 53' W20-7a (9) ones elineats, 23' max. spacing uffer ee hart "" WORK RE ee hart "" ee hart "" 100' max. Optional Vehicle ividing Line enterline (30) 36" X 36" 30" X 30" 36" X 18" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 3
5 FIGURE MULTI-LNE OUTIE LNE LOURE EYON INTERETION Indicate Nth Taper L ee hart "" 50' min. between delineats Within 125' Varies ee hart "" WORK RE ee hart "" Install tempary No Parking signs (if required) ee Note 4 W9-3 rt (20 rt) (30) R3-7 rt (R18 rt) (30) * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 4
6 FIGURE MULTI-LNE ONE WY MULTI-LNE LOURE (LEFT N RIGHT IE LOURE TO E IMILR) Overlay (as appropriate) 2 (30) W9-3 rt (20 rt) ones elineats 23' maximum spacing One flashing arrow sign f each lane closed 200' min. Taper L 1/2 L Taper L ee hart "" 2 Overlay (as appropriate) W9-3 rt (20 rt) * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth ones elineats 26' maximum spacing Median ividing Line WORK RE Varies Median ividing Line 150' min. uffer Zone REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 5
7 FIGURE E MULTI-LNE OUTIE LNE LOURE ee hart "" Taper L 150' min. uffer Zone WORK RE Install tempary No Parking igns (if required) ee Note 4 W9-3 rt (20 rt) (30) * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 6
8 FIGURE F MULTI-LNE LEFT LNE LOURE EYON INTERETION Indicate Nth R3-2 (R17) W21-1a (22) R3-2 (R17) W9-3L (20 modified) ee hart "" F Raised Median WORK RE WORK RE F triped Median ee hart "" R3-2 (R17) W21-1a (22) R3-2 (R17) W9-3L (20 modified) 24" x 24" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 7
9 FIGURE G MULTI-LNE INIE LNE LOURE (30) WORK RE Taper L 150' min. ee hart "" Install tempary No Parking igns (if required) ee Note 4 W9-3L (20 lt) * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Varies 10' min. Taper L ee hart "" Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 8
10 FIGURE H MULTI-LNE WORK WITHIN HOULER houlder WORK RE 100' ± 1/3 Taper L 100' ± ones ellineats 23' maximum spacing ones elineats 23' maximum spacing * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 9
11 FIGURE I MULTI-LNE INIE LNE LOURE EYON INTERETION Indicate Nth Taper L ee hart "" ee hart "" WORK RE 10' min. ee hart "" 50' min. between delineats (30) (30) W9-3 lt (20 lt) * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 10
12 FIGURE J MULTI-LNE INIE LNE LOURE T INTERETION Indicate Nth ee Figure f Right Lane losure ee hart "" ee hart "" Y ee Note 7 10' max. E F R9-3a (R96) R9-3b (R96) WORK RE 30' min. between elineats Install tempary No Parking signs (if req'd) Taper L ee hart "" E R9-3a (R96) R9-3b (R96) F (30) ee hart "" E 24" x 24" 18" x 18" F 18" x 12" W9-3 lt (20 lt) ee chart "" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 11
13 FIGURE K MULTI-LNE LOING OF HLF RO W1-3L / W1-4L (W2 lt / W1 lt) ee Note 7 W20-4 W13-1 (W6) ee Note 8 1 Taper L 2 L Taper L 150' min. 1 Taper L 2 L Taper L W9-3L (20 lt) ee hart "" WORK RE ee hart "" W1-3R / W1-4R (W2 rt / W1 rt) ee Note 7 (30) R (30) W13-1 (W6) ee Note 8 24" x 24" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 12
14 FIGURE L MULTI-LNE WORK WITHIN INTERETION W9-3L (20 lt) W21-1a (22) W9-3L (20 lt) W21-1a (22) Indicate Nth R3-2 (R17) W9-3L (20 lt) WORK RE W21-1a (22) W21-1a (22) W9-3L (20 lt) 24" x 24" Y ee hart "" Taper L ee hart "" (8) Total Taper L Taper L Taper L ee hart "" ee hart "" Y * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 13
15 FIGURE M IYLE LNE LOURE W11-1 W16-1 W9-3a (20 ike) Install tempary No Parking signs (if required) ee Note 4 PRKING LNE IKE LNE WORK RE WORK RE ee hart "" Install tempary No Parking signs (if required) ee Note 4 (30 ike) 18" x 24" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. (30 ike) ee hart "" IKE LNE W9-3a (20 ike) W11-1 W16-1 Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 14
16 FIGURE N TWO-LNE TWO WY LEFT TURN LNE ONE WY LOURE R ones elineats, 23' max. spacing Taper L WORK RE Optional Vehicle (30) 36" X 36" 30" X 30" 36" X 18" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. ee hart "" Taper L Indicate Nth IE TREET R3-2 (R17) uffer ee hart "" Taper L ee hart "" 24" X 24" REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 15
17 FIGURE O MULTI-LNE TWO WY LEFT TURN LNE LOING OF HLF RO W20-4 W1-3L / W1-4L (W2 lt / W1 lt) ee Note 7 W13-1 (W6) ee Note 8 ee hart "" 1 2 L ee hart "" Taper L Taper L 1 2 L 150' Taper L Taper L WORK RE ee hart "" W1-3R / W1-4R (W2 rt / W1 rt) ee Note 7 (30) R (30) W13-1 (W6) ee Note 8 36" X 36" 30" X 30" 36" X 18" 24" X 24" * EE PGE 1 THI PPENIX FOR LEGEN, NOTE N PING REQUIREMENT. Indicate Nth REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 16
18 FIGURE P IEWLK LOURE Indicate Nth WORK RE R11-2 (idewalk) 48" min. WORK RE Optional 36" X 36" 30" X 30" IEWLK ETOUR ETIL 1 IEWLK IVERION ETIL 2 36" X 18" 10" X 24" NOTE: TEMPORRY PEETRIN E PTHWY HLL OMPLY WITH N HLL INLUE RMP N HNRIL PER THE LIFORNI UNIFORM UILING OE REQUIREMENT. alifnia MUT REVIION Y PP TE GUIELINE FOR ONTRUTION ZONE Engineering tandards - ppendix G page 17
Two-Lane, Two-Way Roads
Two-Lane, Two-Way Roads road consisting of two opposing lanes of undivided traffic. Two-Lane Two-Way *Drawings Not To Scale mndot.gov/fieldmanual Field Manual January 08 Intermediate Volume Up to 00 DT
Handbook for Temporary Traffic Control - Construction, Maintenance, and Utility Operations
Purdue University Purdue e-pubs Indiana Local Technical ssistance Program (LTP) Publications Indiana Local Technical ssistance Program (LTP) 7-2004 Handbook for Temporary Traffic Control - Construction,
TRAFFIC CONTROL PLAN FOR SURVEYING OPERATIONS END ROAD WORK END ROAD WORK * ** END ROAD WORK END ROAD WORK. TCP (S-1a) TCP (S-1b)
kind is made by TxDOT for any purpose whatsoever. TxDOT assumes no responsibility for the conversion of this standard to other formats or for incorrect results or damages resulting from its use. 3 for
Exhibit H: Typical Traffic Control Plans. North Metro Natural Gas Pipeline Project Routing Study
Exhibit H: Typical Traffic Control Plans North Metro Natural Gas Pipeline Project Routing Study North Metro Natural Gas Pipeline Project Routing Study This page intentionally left blank. Contractor: CAMPOS
SECTION 12 - CONSTRUCTION AREA TRAFFIC CONTROL TABLE OF CONTENTS
SECTION 12 - CONSTRUCTION AREA TRAFFIC CONTROL TABLE OF CONTENTS Section Page 12-1 GENERAL...12.1 12-2 FLAGGING...12.1 12-2.01 Flaggers...12.1 12-2.02 Flagging Costs...12.1 12-3 TRAFFIC-HANDLING EQUIPMENT
Two-Way, Continuous. Turn Lane
Two-Way, Continuous Two-Way, eft Continuous Turn ane eft Turn ane roadway with a center lane between opposing lanes of traffic that allows traffic from either direction to make left turns off the roadway.
SN01 STANDARD NOTES CITY OF SAMMAMISH 2018 FLASHING YELLOW ARROW SIGNALS PROJECT NO. DATE BY APPR REVISION COSA0023 KING COUNTY WASHINGTON
STANDARD NOTES SN01 2 OF 8 ROADWAY PLAN PL01 3 OF 8 ROADWAY PLAN PL02 4 OF 8 LANE 10 105 150 205 270 450 500 550 11 12 SHOULDER 115 125 MINIMUM LANE CLOSURE TAPER LENGTH = L 165 225 295 180 245 320 5 25
Night Work Specification
Night Work Specification 1.0 Hours of Work The contractor is advised that most work for this contract will be carried out during night time hours. For the purposes of this contract night is defined as
Louisiana s s Work Zone Task Force Work Zone Improvements
Louisiana s s Work Zone Task Force Work Zone Improvements Louisiana Asphalt Technology Conference Shreveport, Louisiana February 24, 2005 Charles Adams, P.E., PTOE Why Improve Work Zones? Number of Work
STATE ND PROJECT NO. CP 0883 (14) & CP 1152 (14) SHEET NO. TOTAL SHEETS 9 31 SIGN NUMBER SIGN SIZE DESCRIPTION AMOUNT REQUIRED UNITS PER AMOUNT UNITS
STATE ND PROJECT NO. CP 0883 (14) & CP 1152 (14) SHEET NO. TOTAL SHEETS 9 31 SIGN NUMBER SIGN SIZE DESCRIPTION AMOUNT REQUIRED UNITS PER AMOUNT UNITS SUB TOTAL SIGN NUMBER SIGN SIZE DESCRIPTION AMOUNT
LaDOTD s s New Traffic Control Details
LaDOTD s s New Traffic Control Details Louisiana Pavement Conference Baton Rouge, Louisiana October 7, 2004 Charles Adams, P.E., PTOE Objectives Traffic Background Information What Drove the Department
TRAFFIC ENGINEERING DIVISION INSTRUCTIONAL & INFORMATIONAL MEMORANDUM
VIRGINIA DEPARTMENT OF TRANSPORTATION TRAFFIC ENGINEERING DIVISION INSTRUCTIONAL & INFORMATIONAL MEMORANDUM GENERAL SUBJECT: Portable Temporary Rumble Strips (PTRS) SPECIFIC SUBJECT: Guidelines for the
KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, EDITION 2007
07-08001 Sheet 1 of 2 KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, EDITION 2007 SECTION 805 WORK ZONE TRAFFIC CONTROL AND SAFETY TYPICAL TRAFFIC CONTROL, 2-LANE
SN01 STANDARD NOTES CITY OF SAMMAMISH 2018 INTERSECTION IMPROVEMENTS PROJECT NO. DATE BY APPR REVISION COSA0023 KING COUNTY WASHINGTON
STANDARD NOTES SN01 2 OF 17 STANDARD NOTES SN02 3 OF 17 SITE PREP & T.E.S.C. NOTES GENERAL NOTES SITE PREP & T.E.S.C. PLAN SP01 4 OF 17 SITE PREP & T.E.S.C. NOTES GENERAL NOTES SITE PREP & T.E.S.C. PLAN
Work Zone Safety. Guidelines for Temporary Traffic Control
Work Zone Safety Guidelines for Temporary Traffic Control Revised April 2015 1 Table of Contents Introduction 3 Traffic Control Devices 4 Signs 4 Channelizing Devices 7 Lighting Devices 11 Component Parts
STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 961 PORTABLE TRAFFIC SIGNALS OCTOBER 17, 2008
961.01 Description 961.02 Prequalification 961.03 Requirements STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 961 PORTABLE TRAFFIC SIGNALS OCTOBER 17, 2008 961.01 Description. This
REVIEW OF THE DRAFT 2011 VA WORK AREA PROTECTION MANUAL. December 14, 2010 David Rush VDOT WZS Program Manager
REVIEW OF THE DRAFT 2011 VA WORK AREA PROTECTION MANUAL December 14, 2010 David Rush VDOT WZS Program Manager Manual on Uniform Traffic Control Devices (MUTCD) Released in December 2009 States have until
Work Zone Safety. Mike Marr Industrial Safety Consultant Ohio Bureau of Workers Compensation Division of Safety & Hygiene
Work Zone Safety Mike Marr Industrial Safety Consultant Ohio Bureau of Workers Compensation Division of Safety & Hygiene 1 Agenda Manuals/Codes/Statistics Setup & Removal of Work Zones Devices and Locations
Major engine repairs are available.
irport Information etails for TVUX ity LE State/Province ountry FR Latitude N 47 0' 34.00" Longitude E 5 6' 06.00" Elevation 645 Longest Runway 7300 Magnetic Variance E 0.0 Fuel Type 00 Low Lead (LL) octane
Anticipated Changes Based on 2009 Federal MUTCD
Anticipated Changes Based on 2009 Federal MUTCD Section 1A.13 Meanings of text headings (Standard, d Guidance, Option, Support) relocated and clarified Standard d statements shall hll not be modified difid
South Carolina. It s serious. Deadly serious.
South Carolina It s serious. Deadly serious. Work Zone Safety Guidelines for the South Carolina Department of Transportation, Municipalities, Counties, Utilities, and Contractors 2013 1 Table of Contents
2013 Changes to the 2011 MMUTCD, Part 6 September 2013
2013 Changes to the 2011 MMUTCD, Part 6 September 2013 The requirements for drum spacing in Sections 6C.07 (Page 557 (MI)) and 6F.63 (Page 604 (MI)) have been revised to more closely match the pavement
Section 6H.01 Typical Applications
December 27, 2010 Draft Page 6H-1 Section 6H.01 Typical Applications Support: 01 Whenever the acronym TTC is used in this Chapter, it refers to temporary traffic control. 02 The needs and control of all
Manual on Uniform Traffic Control Devices Supplement For The City of Colorado Springs
Final Draft Manual on Uniform Traffic ontrol Devices Supplement For The ity of olorado Springs Revised 07/01/2005 Final Draft TE OF ONTENTS Table of ontents 2 Executive Summary 3 Introduction 4 Goals 5
Public Improvement Permit Instructions
Public Improvement Permit Instructions Occupancy Fees are charged for any work impacting the public right of way. The Street Occupancy Fee will apply whenever any portion/lane of any public sidewalk, alley,
2 Min. Min. Edge of. Edgeline See Note 3 PLAN VIEW. See Note 3. This distance may vary
8" Physical gore ( ) ( ) 250 Varies 250 TYPICAL RUMBLE STRIP PLACEMENT AT EXIT AND ENTRANCE RAMPS This distance may vary This distance may vary ( ) 2 16" edge of R=12" Max ( ) Physical gore Texturing 1.
Temporary Traffic Control Plans
Temporary Traffic Control Plans US Department of Transportation Federal Highway Administration (FHWA) MUTCD 2009 EDITION Adopted by WSDOT December 19, 2011 with modifications per WAC 468-95. 2-1 Standard
No valido para navegacion real
HNGES: onstruction area, parking spots. SNR pt Elev 920' S27 29.8 W064 56.2 TERMS E RIO HONO, RGENTIN TERMS E RIO HONO Tower TERMS E RIO HONO *119.85 64-57 64-56 27-29 27-29 19 189^ Elev 920' 07^W 8202'2500m
PERFORMANCE ACTIVITY 603 SIGNS
PERFORMANCE ACTIVITY 603 SIGNS WORK DESCRIPTION 3 WORK DESCRIPTION 4 WORK DESCRIPTION 6 New Install Maintenance / Replace Temporary 603 SIGNS ACTIVITY DESCRIPTION Install new signs and maintain and replace
General Info Stornoway, GBR N ' W ' Mag Var: 7.9 W Elevation: 26'
irport Information EGPO (tornoway) General Info tornoway, GR N 58.9' W 06 9.9' Mag Var: 7.9 W Elevation: 6' Public, ontrol Tower, IFR, Landing Fee, ustoms availble on a restrcted basis Fuel: 00LL, Jet
RESORT MUNICIPALITY OF WHISTLER BYLAW NOTICE ENFORCEMENT AMENDMENT BYLAW NO. 2194, 2018
RESORT MUNICIPALITY OF WHISTLER BYLAW NOTICE ENFORCEMENT AMENDMENT BYLAW NO. 2194, 2018 A BYLAW TO AMEND BYLAW NOTICE ENFORCEMENT BYLAW NO. 2174, 2018. WHEREAS the Council of the Resort Municipality of
801-R-xxx LAW ENFORCEMENT OFFICER FOR WORK ZONE SAFETY. (Adopted xx-xx-17)
801-R-xxx LAW ENFORCEMENT OFFICER FOR WORK ZONE SAFETY (Adopted xx-xx-17) Description This work shall consist of providing a Law Enforcement Officer, LEO, to assist with the safe, efficient, orderly movement
REVIEW OF SIGNIFICANT CHANGES IN THE 2011 VIRGINIA WORK AREA PROTECTION MANUAL. VDOT Traffic Engineering Division Oc7, 2011 Presentation
REVIEW OF SIGNIFICANT CHANGES IN THE 2011 VIRGINIA WORK AREA PROTECTION MANUAL VDOT Traffic Engineering Division Oc7, 2011 Presentation VA Supplement to the MUTCD VDOT developed Supplements which consist
Virginia Tech Transportation Institute
Virginia Tech Transportation Institute Background VTTI was established in August 1988 by agreement between US DOT and the University Transportation Centers Program We focus on Safety and Efficiency in
Temporary Traffic Control Manual
Temporary Traffic Control Manual For Street Construction and Maintenance Operations in the City of Appleton Prepared by the City of Appleton Department of Public Works Engineering Division Traffic Section
JEPPESEN JeppView
REVISION LETTER For isc 23-07 Page hanged chart(s) since isc 22-07 = dded chart, REV = Revised chart, EL = eleted chart. T PROEURE IENT INEX REV TE EFF TE Monterrey, (el Norte Intl - MMN) ONON EP -3 6
Work Zone Safety & New Interstate Resurfacing Provision
2017 CAPA Presentation Work Zone Safety & New Interstate Resurfacing Provision Steve Kite, PE State Work Zone Engineer Work Zone Safety Data In 2016, Approximately 600 construction projects across NC (not
STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 808 DIGITAL SPEED LIMIT (DSL) SIGN ASSEMBLY.
808.01 Description 808.02 Materials 808.03 Design Speed 808.04 Construction 808.05 Method of Measurement 808.06 Basis of Payment STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 808
DELINEATOR REFERENCE POINT 200' TYPICAL SPACING (YELLOW DELINEATORS) END OF MERGE LANE TAPER DELINEATOR REFERENCE POINT
200' TYP. 0' < EACH SIDE BOTH ROADWAYS END OF MERGE LANE TAPER TYPICAL FOR ALL 2-LANE MERGES EXCEPT WHERE THERE IS A MERGE FROM THE RIGHT AND NO OFFSET IN THE THROUGH LANES END OF MERGE LANE TAPER 200'
DEPARTMENTAL MATERIAL SPECIFICATIONS TRAFFIC CONTROL PLAN TYPICAL DETAILS WZ(TD)-13 BARRIER DELINEATION WITH MODULAR GLARE SCREENS
Concrete Barrier NOTES: 1. Length of Safety Glare Fence will be specified elsewhere in the plans. 2. The cumulative nominal length of the modular units shall equal the length of the individual sections
panelsizes:min.:30x30,std.:36x36,exp.:36x36,fwy.:48x48 levels:gscolorfill GSBWFILL GSOUTLINE chevronshoulderradius: constructpanels: pan
panelsizes:min.:30x30,std.:36x36,exp.:36x36,fwy.:48x48 levels:gscolorfill GSBWFILL GSOUTLINE chevronshoulderradius:12.000 constructpanels:36 24 18 panelborderradius:12.000 chevrontipradius:12.000 panelstyle:warning.ssi
BID SUMMARY SHEET PUBLIC BID NO TRAFFIC WARNING/STREET SIGNS AND SUPPLIES BIDS RECEIVED: MARCH 29, 2016
1 EACH R1-1 - 30" X 30" Stop Sign $22.90 $23.62 2 EACH R1-2 - 36" x 36" x 36" Yield Sign $16.29 $18.00 3 EACH R1-2 - 24" x 24" x 24" Yield Sign $12.54 $10.03 4 EACH R1-6a-Ped X-ing $22.80 $43.80 5 EACH
TRAFFIC REGULATION APPROVAL PROCESS
Approved: Effective: August 22, 2017 Review: June 21, 2017 Office: Traffic Engineering and Operations Topic No.: 750-010-011-e Department of Transportation PURPOSE TRAFFIC REGULATION APPROVAL PROCESS To
BID SUMMARY SHEET CONTRACT NO
1 EACH R1-1 - 30" X 30" Stop Sign $23.61 $23.58 2 EACH R1-2 - 36" x 36" x 36" Yield Sign $16.36 $16.61 3 EACH R1-2 - 24" x 24" x 24" Yield Sign $12.55 $13.24 4 EACH R3-1 - 12" x 6" 4-Way $2.76 $1.98 5
Maintaining Pavement Marking Retroreflectivity
Supplemental Notice of Proposed Amendment: Maintaining Pavement Marking Retroreflectivity Kyle Armstrong, P.E., PTOE Acting Engineer of Traffic Operations https://safety.fhwa.dot.gov/ Rule Making Process
JeppView for Windows. JeppView for Windows. jep=jeppesen. jep=jeppesen. Trip Kit Index. Airport Information For EFKT
Trip Kit Index Printed on 3 Jul 8 Page (c) SNERSON, IN., 8, LL RIGHTS RESERVE jep= JeppView for Windows irport Information For EFKT Printed on 3 Jul 8 Page (c) SNERSON, IN., 8, LL RIGHTS RESERVE jep= JeppView
JeppView for Windows. General Information. Runway Information. Communication Information. jep=jeppesen
irport Information For ESKM Printed on 27 Jan 208 Page (c) SNERSON, IN., 208, LL RIGHTS RESERVE jep= JeppView for Windows General Information Location: MOR SWE IO/IT: ESKM / MXX Lat/Long: N60 57.52', E04
NCUTCD Proposal for Changes to the Manual on Uniform Traffic Control Devices
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 TECHNICAL COMMITTEE: ITEM NUMBER: TOPIC: ORIGIN OF REQUEST: AFFECTED SECTIONS OF MUTCD: NCUTCD Proposal for Changes
TRAFFIC CONTROL PLAN ONE-LANE TWO-WAY TRAFFIC CONTROL TCP(1-2)-12 ONE LANE TWO-WAY CONTROL WITH YIELD SIGNS ONE LANE TWO-WAY CONTROL WITH FLAGGERS
DISCLAIMER: The use of this standard is governed by the "Texas Engineering Practice Act". No warranty of any kind is made by TxDOT for any purpose whatsoever. TxDOT assumes no responsibility for the conver-
Diagram 1 - Shoulder Assistance
Diagram - Shoulder Assistance Approx. skip (40 ). Notify K. C. Scout. Turn on the emergency directional flashers and top rear facing strobe lights. 3. Pull to the shoulder and stop approximately 40 feet
Work Zone Safety Best Practices Traffic Engineering & Safety Conference October 18, Dean Mentjes Federal Highway Administration
Work Zone Safety Best Practices Traffic Engineering & Safety Conference October 18, 2017 Dean Mentjes Federal Highway Administration Juan Pava Illinois Department of Transportation 1 Setting the Stage:
Which US President was most responsible for the development of the US Interstate System?
EE 30 Midterm Sample Quetion Short Anwer Which US Preident wa mot reponible for the deelopment of the US Intertate Sytem? Eienhower What metric i ued to calculate interection Leel of Serice? Etimated aerage
EL DORADO COUNTY REGIONAL FIRE PROTECTION STANDARD
EL DORADO COUNTY REGIONAL FIRE PROTECTION STANDARD EMERGENCY APPARATUS ACCESS WAYS STANDARD #B-003 EFFECTIVE 05-05-2009 PURPOSE To establish a consistent guideline for fire access roadways required by
2. ELIGIBILITY REQUIREMENTS
Speed Hump Policy 1. GENERAL The purpose of this policy is to provide guidelines for the application of speed humps. A "speed hump" is a gradual rise and fall of pavement surface across the width of the
Work Zone Changes Since We Last Met 2016 Louisiana Transportation Conference. Barry L. Lacy, P.E. Work Zone/Claims/Audit Engineer
Work Zone Changes Since We Last Met 2016 Louisiana Transportation Conference Barry L. Lacy, P.E. Work Zone/Claims/Audit Engineer Louisiana State Motto Why is Work Zone Safety Important? US Work Zone Fatalities
NO VALIDO PARA NAVEGACION REAL
HNGES: irport diagram, runway bearings, parking spots added. 430' pt Elev S7 3. W055 58. SS, LIERTOR GRL JOSE E SN MRTIN *SS Tower 0. 55-59 55-58 55-57 Elev 376' 9 93^ UTION: irds in vicinity of airport.
DESIGNATED CONSTRUCTION ZONE SPEED FINES DOUBLE. Manitoba Infrastructure and Transportation. Infrastructure and Transportation. Traffic Engineering
CONSTRUCTION DESIGNATED ZONE SPEED FINES DOUBLE Manitoba Infrastructure and Transportation Work Zone Traffic Control Manual Provincial Roads and Provincial Trunk Highways Infrastructure and Transportation
Created by: St. Louis County
Created by: Victor Lund, PE Traffic Engineer St. Louis County Ken Johnson, PE, PTOE State WZ, etc. MnDOT Why do workers want speed limits? How effective are speed limits in work zones? New legislation
JeppView for Windows. General Information. Runway Information. Communication Information. jep=jeppesen
irport Information For LWOH Printed on 27 Jan 2018 Page 1 (c) SNERSON, IN., 2018, LL RIGHTS RESERVE jep= JeppView for Windows General Information Location: I MK IO/IT: LWOH / OH Lat/Long: N41 10.80', E020
JeppView for Windows. General Information. Runway Information. Communication Information. jep=jeppesen
irport Information For EKRN Printed on 7 Jan 08 Page (c) SNERSON, IN., 08, LL RIGHTS RESERVE jep= JeppView for Windows General Information Location: ORNHOLM NK IO/IT: EKRN / RNN Lat/Long: N55 03.80', E04
VDOT 2008 Road and Bridge Standards Section Transition Curves
õíßáßáwúkÿîßá VDOT 2008 Road and Bridge s Page Title TC-5.01 & 5.04 802.01 802.02 802.03 802.04 802.05 802.06 Explanation of Tables and Instructions for Use General Conditions Transition Curves for Rural
POLICY ON SPEED HUMPS
POLICY ON SPEED HUMPS PURPOSE: The purpose of this policy is to provide guidelines for the installation of speed humps along local residential streets within Miami-Dade County. POLICY: Speed humps will
JeppView for Windows. List of pages in this Trip Kit. jep=jeppesen. Trip Kit Index
Trip Kit Index Printed on 28 Jun 2015 Page 1 (c) SNERSON, IN., 2015, LL RIGHTS RESERVE jep= JeppView for Windows List of pages in this Trip Kit Trip Kit Index irport Information For TTP Terminal harts
Airport Information. Details for DEBRECEN. State/Province
irport Information etails for ity State/Province ountry HUN Latitude N 47 29' 20.00" Longitude E 2 36' 55.00" Elevation 359 Longest Runway 8200 Magnetic Variance E 4.0 Fuel Type 00 Low Lead (LL) octane
Advance Warning System with Advance Detection
N-0002 dvance Warning System with dvance Detection Intersections with limited visibility, high speeds (55 mph and greater), temporary or newly installed intersections, or grade issues often need an advanced
DIVISION 4: STREET. Improvement Design Standards City of Dundee Oregon. Division 4 : Street Page 1
DIVISION 4: STREET 4.1 DESIGN CRITERIA A. APPLICABILITY 1. These Design Standards shall govern the construction and upgrade of all public and private streets in the City of Dundee and applicable work within
APPENDIX A Basis of Design and Design Criteria Memorandum
APPENDIX A Basis of Design and Design Criteria Memorandum Job No: Y01-500 Files are stored in: Engineering / Client / Yolo/Y01500 Buckeye and Rumsey/Rumsey CR 41 over Cache Creek, CAD files stored in:
PN /21/ SURFACE SMOOTHNESS REQUIREMENTS FOR PAVEMENTS
PN 420-10/21/2016 - SURFACE SMOOTHNESS REQUIREMENTS FOR PAVEMENTS DESCRIPTION: The surface tolerance specification requirements are modified as follows for all pavements of constant width with at least
s Contact the Area Construction Engineer at for RAP sample location. Page 2 of 10
Page 1 of 10 Page 2 of 10 Page 3 of 10 Ú City limit or Urban boundary No Centerline rumble strips Centerline rumble strips City connecting link or Urbanized (Unincorporated city) TYPICAL CITY CONNECTING
Work Zone Worker Protection
Work Zone Worker Protection Field Guide Developed by American Traffic Safety Services Association 15 Riverside Parkway, Suite 100 Fredericksburg, VA 22406 (800) 272-8772 Web Address: www.atssa.com E-mail:
Regulation ECE Related Entries:
Regulation ECE Related Entries: Responsible Office: ECE Associate Superintendent for Operations ECE-R: Traffic and Parking Procedures Las Cruces Public Schools TRAFFIC AND PARKING PROCEDURES I. PURPOSE
Questions and Answers from March 1 st, 2016 Roadbuilders Introduction Webinar
Questions and Answers from March 1 st, 2016 Roadbuilders Introduction Webinar No. Question Answer 1 Is it mandatory to have an Engineer sign off on all TMP's containing a lane closure even in a 50 or 60
Regulatory Signs in Nomenclature Order
Regulatory Signs in Nomenclature Order Nomenclature Description Sizes (mm x mm) R 1-1 STOP 600x600 750x750 900x900 1200x1200 R 1-1A RIGHT LANE KEEP MOVING 600x750 750x900 R 1-1B OPPOSING TRAFFIC DOES NOT
JeppView for Windows. General Information. Runway Information. Communication Information. jep=jeppesen
irport Information For ESOW Printed on 27 Jan 208 Page (c) SNERSON, IN., 208, LL RIGHTS RESERVE jep= JeppView for Windows General Information Location: STOKHOLM SWE IO/IT: ESOW / VST Lat/Long: N59 35.37',
CATEGORY 500 PAVING SECTION 535 PAVEMENT SURFACE PROFILE
CATEGORY 500 PAVING 1 of 9 SECTION 535.01 DESCRIPTION. This work shall consist of measuring the roughness of the final surface of hot mix asphalt (HMA) or portland cement concrete (PCC) pavements. The
CONTENTS I. INTRODUCTION... 2 II. SPEED HUMP INSTALLATION POLICY... 3 III. SPEED HUMP INSTALLATION PROCEDURE... 7 APPENDIX A... 9 APPENDIX B...
Speed Hump Program CONTENTS I. INTRODUCTION... 2 II. SPEED HUMP INSTALLATION POLICY... 3 1. GENERAL... 3 2. ELIGIBILITY REQUIREMENTS... 3 A. PETITION... 3 B. OPERATIONAL AND GEOMETRIC CHARACTERISTICS OF
CLAY COUNTY MISSOURI HIGHWAYS AND TRANSPORTATION COMMISSION PLANS FOR PROPOSED STATE HIGHWAY NOT TO SCALE LENGTH OF PROJECT
DI E INDE OF SHEETS TYPICAL SECTIONS (TS) ( SHEET)--- QUANTITIES (QU) (7 SHEETS)--------- 3 PLAN-PROFILE (PP)------------------ REFERENCE POINTS (RP)-------------- COORDINATE POINTS (CP)------------- CULVERT
59-2 KA Page 1 of 16
59-2 KA 4812-01 Page 1 of 16 Area office to Page 2 of 16 Rock Wedge TYPICAL SECTION C 2.0 in. Overlay 2.0 in. Mill Rock Wedge 1:1 @ edge of Asphalt Match Existing Surface 30.0 ft wedge 2.0ft+ not to scale
General Info Krabi, THA N ' E ' Mag Var: 0.0 W Elevation: 93' Runway Info Runway ' x 148' asphalt
irport Information VTSG (Krabi) General Info Krabi, TH N 08 05.8' E 98 59.3' Mag Var: 0.0 W Elevation: Public, ontrol Tower, IFR, No Fee, Rotating eacon, ustoms availble on a restrcted basis Time Zone
LOS ZDA ZRA ZDA ZRA ZRA ZRA SPL ZADAR, CROATIA ZADAR, CROATIA LDZD/ZAD LDZD/ZAD ALANU 1B
-2.STR. lt Set: hpa 1 [LN1] 1 [LN1], 3 RWYS 04, 14, 32 RRIVLS FROM NORTH & SOUTH SPEE: MX 250 KT ELOW FL0-2 lt Set: hpa 2F [EIT2F] LOS 4, MINTU 1E [MINT1E] 1 [ULPI1], 1 RWYS 04, 14, 32 RRIVLS FROM NORTHWEST
Plan Check Policies and Guidelines
Plan Check Policies and Guidelines VII. A. INTRODUCTION Traffic signing and striping plans are required for all General Plan Roads and any roadway that is 56-foot wide curb-to-curb (78 R/W) or wider. Transportation
Access Management Standards
Access Management Standards This section replaces Access Control Standards on Page number 300-4 of the Engineering Standards passed February 11, 2002 and is an abridged version of the Access Management
TTI TRAFFIC SAFETY CONFERENCE. John A. Barton, P.E.
TTI TRAFFIC SAFETY CONFERENCE John A. Barton, P.E. Introduction TxDOT Mission Work with others to provide safe and reliable transportation solutions for Texas. 2 Mission Zero Is a Journey toward: Zero
SCDOT TRAFFIC SIGNAL SPECIAL PROVISIONS TRAFFIC CONTROL FOR TRAFFIC SIGNAL PROJECTS MAINTENANCE OF TRAFFIC
SCDOT TRAFFIC SIGNAL SPECIAL PROVISIONS TRAFFIC CONTROL FOR TRAFFIC SIGNAL PROJECTS MAINTENANCE OF TRAFFIC TRAFFIC CONTROL: The Contractor shall execute the item of Traffic Control as required by the Standard
a. A written request for speed humps must be submitted by residents living along the applicable street(s) to the Public Works Department.
WASHOE COUNTY POLICY FOR INSTALLATION OF SPEED HUMPS BACKGROUND The quality of life in residential neighborhoods can be significantly affected by the traffic issues of speeding and high vehicle volumes.
CITY AND COUNTY OF DENVER DEPARTMENT OF PUBLIC WORKS STATEMENT OF QUANTITIES. Item No. Description Estimated Quantity
202-00019 Removal of Inlet 15 EA 202-00035 Removal of Pipe 121 LF 202-00200 Removal of Sidewalk 1,057 SY 202-00203 Removal of Curb and Gutter 2,142 LF 202-00206 Removal of Concrete Curb Ramp 320 SY 202-00207
Horizontal Alignment
Session 8 Jim Rosenow, PE, Mn/DOT March 5-7, 2010 Horizontal Alignment The shortest distance between two points is: A straight line The circumference of a circle passing through both points and the center
Maine Turnpike Authority
Company Name Total Bid Amount CPM Constructors - Freeport, ME $1,309,765.25 Scott Construction Corporation - Portland, ME $1,528,840.00 Wyman & Simpson Inc. - Richmond, ME $1,674,845.00 Page 1 of 10 CPM
CHAPTER 11 - TRAFFIC
CHAPTER 11 - TRAFFIC Article 11-1 ENFORCEMENT 1 It shall be the duty of the Town Law Enforcement and/or its designated agency to provide for the enforcement of the traffic regulations of the town and all
W Type: Denotes functional type of sign (R = regulatory, W = warning, D = guide signs, and M = route markers)
Introduction: Traffic Signs The anual on Uniform Traffic Control Devices for Streets and Highways (UTCD) has been adopted as the standard for all Regulatory and Warning signs used on Corps project roadways
REVISION VIRGINIA WORK AREA PROTECTION MANUAL. Effective April 1, 2015 for State Forces & Effective starting on the July 2015 Advertisement
REVISION 1 2011 VIRGINIA WORK AREA PROTECTION MANUAL Effective April 1, 2015 for State Forces & Effective starting on the July 2015 Advertisement VA Supplements to the MUTCD Revisions to VDOT developed
3.15 SAFETY AND SECURITY
3.15 SAFETY AND SECURITY Introduction This section describes the environmental setting and potential effects of the alternatives analyzed in this EIR with regard to safety and security in the SantaClara-Alum
ELECTRICAL PANELBOARD SCHEDULES AND RISER DIAGRAM EP09.01
TPL P 400 MB PP PL G PL PL P P 75G HB H H OREBOAR 50 00 50 00 GENERAL RIER NOTE:. WHEREVER THE LENGTH OF THE EONARY ONUTOR OF ANY TRANFORMER EE TEN FEET, AN ENLOE IRUIT BREAKER OR FUE IONNET I REQUIRE
CAPCOG TRAFFIC SIGNS, POSTS & CONTROL DEVICES
CAPCOG 2018-19 TRAFFIC SIGNS, POSTS & CONTROL DEVICES Ratified 3/19/18 Winning bid is bold and highlighted. Ordering information is at the end of the document Contract Term April 1, 2018 to March 31, 2019
POLICY AND PROCEDURE FOR SPEED HUMP INSTALLATION. Effective Date: July 10, 2013
CITY OF MORENO VALLEY DEPARTMENT OF PUBLIC WORKS TRANSPORTATION ENGINEERING DIVISION Administration Policy #A-14A POLICY AND PROCEDURE FOR SPEED HUMP INSTALLATION Effective Date: July 10, 2013 Approved
Page 1 of KA
Page 1 of 10 5 Contact the Area Engineer at 620-384-7821 for RAP sample location. Page 2 of 10 SS-1HP or approved alternate shall be used for Tack. Page 3 of 10 Ú City limit or Urban boundary No Centerline
(E) 26'-3" STEEL LIGHT POLE
intelligent infrastructure SITE ID/CASCADE ID-CANDIDATE LETTER: /SF90XSA05C LATITUDE/LONGITUDE: 37.799011/-122.251267 CROSS STREET: 4TH AVE., S. OF E. 18TH ST. CITY, STATE, ZIP: Attachment C intelligent
CHANGE LIST for MDOT Traffic and Safety Geometric Design Guides. May 23, 2017: The following update was made to the web site.
CHANGE LIST for MDOT Traffic and Safety Geometric Design Guides Note: Located at https://mdotjboss.state.mi.us/tssd/tssdhome.htm May 23, 2017: The following update was made to the web site. GEO-650-D Flares
Page
Page Page Page 3 Page 4 Page 5 Page 6 Page 7 Page 9 3-6 I A Policy on Geometric of Highways and Streets A strict application of the maximum relative gradient criterion provides runofflengths for four-lane
Municipality of Anchorage Traffic Department ADDENDUM. Traffic Sign Manual
Municipality of Anchorage Traffic Department ADDENDUM Traffic Sign Manual In accordance with the Alaska Traffic Manual (ATM), all traffic control signs installed on state roads are required to conform