Primed Epicr Casement Windows Custom Wood

Transcription

1 TABL OF CONTNT pecifications QuickpecGuide levations/izes:1/4 &1/8 cale Casement CasementPicture CasementectorTop xtended Half Round xtended Quarter Round GlazingOptions TrimOptions Grille & DL Patterns Unit izing, Rough Openings & Masonry Openings ectiondetails:6 cale December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-1

2 PRODUCT PCIFICATION XTRIOR FINIH The standard exterior is factory-applied latex primer with an option for unfinished (stain grade) natural pine exterior available. AURALAT R WOOD AuraLast R wood is fundamentally different from wood treated in traditional millwork preservation processes in that it uses a proprietary vacuum/pressure process to provide protection throughout the wood parts used to make windows and doors. AuraLast R wood is distinguished from wood using traditional preservation methods by its unique ability to achieve greater penetration of the active ingredients into the wood parts, with a minimum treatment penetration of 92%. INTRIOR FINIH Interior surfaces are unfinished clear pine ready for on-site finishing. Optional prefinished pine interiors include four acrylic colors (Moderate White, xtra White, Natural Choice, Pure White), five stains (Wheat, Cherry, Fruitwood, Cordovan, Cider) and a clear lacquer topcoat. Primed interior is also available. FRAM Frame is assembled from select kiln-dried pine AuraLast R wood on all exterior parts. tandard jamb width is 4-9/16. AH 2-3/32 thick select kiln-dried pine AuraLast R wood. Corner joints are mortised-and-tenoned, with the glass mounted into the sash using a silicone-glazing compound on the exterior and acrylic sealant on the interior, then secured with interior applied profiled wood stops. To accommodate the new nesting crank hardware, the height of the bottom rail has been increased to 2-3/32. GLAZING Insulating glass is constructed from two panes of glass, utilizing a continuous roll formed stainless steel spacer with dual seal sealant. The glass is mounted into the sash using a silicone-glazing compound and secured with interior applied profiled wood stops. All insulating glass units comply with the performance requirements of IGCC in accordance with either ATM 774 or GLAZING OPTION Insulating glass available in Low- with Argon, Low-, Low- 366, Clear, Neat Glass, eedy Reamy, tinted, reflective, or obscure, tempered or other specialty glass as specified. Preserve film is a thick polyethylene film with a low tack acrylic adhesive applied to the glass for protection during shipping and installation. Installations at 4,000 foot elevations and higher require a capillary tube to equalize environmental stress (otherwise known as High Altitude glazing). High Altitude glazing does not allow the use of Argon as listed under glazing options. WATHR-TRIPPING ngineered system combines foam lined bulb seal compressed between the interior of the sash and the frame in a continuous plane on all four sides with a secondary bulb seal compressed between the edge of the sash and the frame. HARDWAR Operating sash are mounted to the frame with corrosion resistant steel hinges. The operating hardware consists of hardened steel worm gears and dual action heavy gauge steel operating arms. The sash is secured with concealed type locking hardware. The interior operator cover, nesting crank handle, and locking handle standard finish options are White, Chestnut Bronze, and Desert and, with optional finishes in plated Polished Brass, Antique Brass, Polished Chrome, Brushed Chrome, Oil-Rubbed Bronze, atin Nickel, and Powder Coat Black. INTRIOR INCT CRN Charcoal fiberglass screen cloth (18x16 mesh) set in painted roll formed aluminum frame fitted to the inside of the window with all necessary hardware, in White, Chestnut Bronze or Desert and finishes. Wood veneer wrapped screen frames and Phantom screens are available in Ponderosa Pine. Insect screens are intended to allow air and light in and to keep insects out. They are not intended to keep anyone or anything from falling through an open window. For safety screens or other security devices contact your local building supply retailer. GRILL DL (imulated Divided Lites) - extruded aluminum muntins permanently applied to the exterior of the insulating glass unit (not available on textured glass) in 5/8, 7/8, 1-1/8, or 1-3/8 widths. Profiles are bead stop in all widths, and a putty profile in 5/8, 7/8, and 1-1/8 widths only. 1 Copper DL is also available. DL is standard with a light bronze internal shadow bar to give a true divided lite appearance. As an option, DL may be ordered with a silver shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Also available is a 2-5/16 DL bar, which simulates a double-hung checkrail. PDL (Precise Divided Lites) - Wood or extruded aluminum muntins permanently applied to the exterior of the insulating unit (not available on textured glass) in 3/4 and 1-1/2 widths without a shadow bar. Clear wood interior muntin bars match the exterior muntin width and are permanently bonded to the interior of the glass. Full-urround Removable Wood Grilles - Rectangular, unfinished interior clear pine wood grilles in 7/8, 1-1/8, and 1-3/8 are available in patterns selected by the owner. GBG (Grilles between the Glass) - 5/8 (15.9mm) flat and 23/32 or 1 contour mounted between the glass panes suspended within the air cavity. XTRIOR TRIM Brickmould standard with optional 3-1/2, 4-1/2, 5-1/2 flat trim, 3-1/2 Adams and 1 x 4 Backband trim. Optional mull covers to accommodate 1 (spread only), 2, 3-1/2 and 6 spread and stud pocket mull. XTNION JAMB xtensions are applied to the interior on all four sides of the frame in wall depths up to 9-1/8 for 4/4 and up to 13-11/16 for 5/4, factory applied. December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-2

3 PRODUCT PCIFICATION INTALLATION Installation per JLD-WN Installation Method for Wood Windows. ee for instructions. PRFORMANC NFRC Certified - (rated and labeled in accordance with NFRC 100 and 200 procedures) ANI/AAMA/NWWDA/101/I AMMA/WDMA/CA 101/I..2/A WDMA Hallmark Certified ee for architectural and performance information. December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-3

4 QUICK PC GUID PCIFICATION TANDARD FATUR OPTIONAL FATUR ome options may require additional lead times. Consult your JLD-WN ales Representative. XTRIOR FINIH Primed Natural Vertical Grain Douglas Fir Mahogany ash Only: Bright Copper* peckled Patina Copper Hand Rubbed Patina Copper (sash only) XTRIOR TRIM Brickmould & ubsill Adams Casing 3-1/2 Flat Casing 4-1/2 Flat Casing *Copper is only available when ordered with a clad sash 5-1/2 Flat Casing xtended ill Nose 1x4 Backband INTRIOR WOOD Western Pine Vertical Grain Douglas Fir Mahogany INTRIOR FINIH Natural Priming Available Pre-finished Interior Options are: Paint - Pure White, xtra White, Natural Choice, Moderate White tain - Wheat, Fruitwood, Cherry, Cordovan, Cider Clear Lacquer IZ Width: 18, 20, 24, 28, 30, 32, 36 Height: 18, 20, 24, 30, 32, 36, 40, 42, 48, 54, 56, 60, 64, 66, 72, 78, 84 GLAZING Low- Insulating Glass (with Argon) Low- 366 Preserve Protective Film GRILL Any Width: 16 to 36 Any Height: 16 to 84 Clear Obscure Reflective Tints: Bronze, Gray, Green Glue Chip afety Laminate in Clear, Bronze or Gray Rain Neat Glass eedy Reamy Narrow Reed andblasted Tempered Impact Resistant High Altitude (Breather Tube, no Argon) DL Bead Profile: 5/8, 7/8, 1-1/8, 1-3/8, 2-5/16 with Light Bronze hadow Bar 5/8, 7/8, 1-1/8, 1-3/8, 2-5/16 with ilver hadow Bar DL Putty Profile: 5/8, 7/8 and 1-1/8 with Light Bronze hadow Bar 5/8, 7/8 and 1-1/8 with ilver hadow Bar 1 Copper DL PDL: 3/4 or 1-1/2 Precise Divided Lite GBG (Grilles between the Glass): 5/8 Flat, 23/32 Contour, 1 Contour Full-urround: 7/8, 1-1/8, 1-3/8 Continued on next page December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-4

5 PCIFICATION TANDARD FATUR HARDWAR Nesting Handle Concealed Locking ystem HARDWAR COLOR White Chestnut Bronze Desert and JAMB Applied, 5/4 4-9/16 QUICK PC GUID OPTIONAL FATUR ome options may require additional lead times. Consult your JLD-WN ales Representative. Round Knob Polished Brass Antique Brass Polished Chrome Up to 9-1/8 4/4 Up to 13-11/16 5/4 Brushed Chrome Oil-Rubbed Bronze INCT CRN Fiberglass Phantom creen and wood veneer wrapped screens available in Pine, Vertical Grain, Knotty Alder, and Mahogany CRN FRAM COLOR White Chestnut Bronze Desert and Wood Veneer (Interior) Ponderosa Pine Vertical Grain Douglas Fir Mahogany Knotty Alder December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-5

6 GNRAL INFORMATION CAMNT DIMNIONAL WINDOW Wood pic casement windows may be specified as dimensional by adjusting the desired rough opening width or height in 1/4 increments from standard. Wood pic casement windows are available with left or right hand operation, or stationary (non-venting). Operating mechanism includes corrosion resistant steel hinges and dual arm roto-type operator with hardened steel gears and operating arms. ash locks are concealed unisontypewithanexposedlockingleverandescutcheonplate.there are several interior hardware finish options. Refer to the pecifications for finish options. MULTIPL AMBLI Wood pic casement windows may be mulled above, below, or beside other wood casement windows, or other wood window products. Factory assembled mulls are limited in height (100 ), width (150 ), and a total area of 75 square feet. December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-6

7 HANDING & OPRATION CAMNT LFT HAND RIGHT HAND OPRATOR OPRATOR CAMNT UNIT HANDING: UNIT HANDING I DFIND (FROM TH XTRIOR) A TH DIRCTION TH AH OPN. December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-7

8 LVATION NOT CAMNT LVATION DRAWING UTILIZ A LIMITD NUMBR OF PROJCTD LIN TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B UD IN A MALL GRAPHICAL CAL. LVATION AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH TRUCTUR. IF MOR DIMNION AR NDD, U TH CTION DRAWING FOR MOR COMPLT DPICTION. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame ize Glass ize 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include subsill. (ubtract 1/2 from Masonry Opening for Unit ize) DP RATING 21 27/32 (555) 23 3/8 (568) 18 3/4 (457) 18 (457) 11 7/8 (302) 50* CWC1818 CWC INDICAT CUTOM WOOD PIC CAMNT TH FIRT TWO NUMBR INDICAT TH UNIT WIDTH BOOK COD TH LAT TWO NUMBR INDICAT TH UNIT HIGHT TANDARD LIT BRAKUP AR HOWN ON ACH LVATION DRAWING GNRAL CAMNT NOT LVATION YMBOL LGND: 1. WOOD PIC CAMNT (WC) UNIT AR AVAILABL A OPRATING OR FIXD UNIT. 2. WCP IN A BOOK COD DNOT TH UNIT I A WOOD PIC CAMNT PICTUR (FIXD) UNIT. 3. UNIT LVATION AR HOWN WITH BRICKMOULD AND UBILL. 4. LVATION DRAWING HOW TANDARD LIGHT CUT FOR OR 1 1/8 [29] GRILL BAR OR IMULATD DIVIDD LIT. 5. OPRATING UNIT AR AVAILABL A LFT OR RIGHT HAND OPRATION. 6. DIMNIONAL VALU IN ( ) AR MILLIMTR CONVRION. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. TATIONARY UNIT. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. OPRATING UNIT UTILIZ TH R65 LOCKING YTM FOR DP RATING. December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-8

9 1-WID UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 35 3/4 (908) 39 3/4 (1010) 26 13/16 (681) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 38 13/16 (986) 42 13/16 (1087) 20 3/4 (527) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 32 3/4 (832) 36 3/4 (933) 20 (508) 24 (610) 28 (711) 30 (762) 32 (813) 36 (914) 13 7/8 (352) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) 17 27/32 (453) 19 3/8 (492) 14 3/4 (375) 14 (356) 7 7/8 (200) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) 50* 50* 50* 50* 50* 50* 50* CWC1814 CWC2014 CWC2414 CWC2814 CWC3014 CWC3214 CWC * 50* 50* 50* 50* 50* 50* CWC1818 CWC2018 CWC2418 CWC2818 CWC3018 CWC3218 CWC * 50* 50* 50* 50* 50* 50* CWC1820 CWC2020 CWC2420 CWC2820 CWC3020 CWC3220 CWC /4 (629) 24 (610) 17 7/8 (454) 50* 50* 50* 50* 50* 50* 50* CWC1824 CWC2024 CWC2424 CWC2824 CWC3024 CWC3224 CWC /4 (781) 30 (762) 50* 50* 50* 50* 50* 50* 50* CWC1830 CWC2030 CWC2430 CWC2830 CWC3030 CWC3230 CWC /4 (832) 32 (813) 50* 50* 50* 50* 50* 50* 50* CWC1832 CWC2032 CWC2432 CWC2832 CWC3032 CWC3232 CWC /4 (933) 36 (914) 50* 50* 50* 50* 50* 50* 50* CWC1836 CWC2036 CWC2436 CWC2836 CWC3036 CWC3236 CWC /4 (1035) 40 (1016) 50* 50* 50* 50* 50* 50* 50* CWC1840 CWC2040 CWC2440 CWC2840 CWC3040 CWC3240 CWC * 50* 50* 50* 50* 50* 50* 42 3/4 (1086) 42 (1067) 13 7/8 (352) 11 7/8 (302) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) 35 7/8 (911) 33 7/8 (860) 21 27/32 (555) 23 3/8 (568) 23 27/32 (606) 25 3/8 (645) 27 27/32 (707) 29 3/8 (746) 33 27/32 (860) 35 3/8 (899) 35 27/32 (910) 37 3/8 (949) 39 27/32 (1012) 41 3/8 (1051) 43 27/32 (1114) 45 3/8 (1153) 45 27/32 (1164) 47 3/8 (1203) CWC1842 CWC2042 CWC2442 CWC2842 CWC3042 CWC3242 CWC3642 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. TATIONARY UNIT. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-9

10 1-WID UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 35 3/4 (908) 39 3/4 (1010) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 38 13/16 (986) 42 13/16 (1087) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 32 3/4 (832) 36 3/4 (933) 24 (610) 28 (711) 30 (762) 32 (813) 36 (914) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) 50* 50* 50* 50* 50* 50* 50* CWC1848 CWC2048 CWC2448 CWC2848 CWC3048 CWC3248 CWC * 50* 50* 50* 50* 50* 50* 54 3/4 (1391) 54 (1372) 47 7/8 (1216) CWC1854 CWC2054 CWC2454 CWC2854 CWC3054 CWC3254 CWC * 50* 50* 50* 50* 50* 50* 56 3/4 (1441) 56 (1422) 49 7/8 (1267) CWC1856 CWC2056 CWC2456 CWC2856 CWC3056 CWC3256 CWC * 50* 50* 50* 50* 50* 50* 60 3/4 (1543) 60 (1524) CWC1860 CWC2060 CWC2460 CWC2860 CWC3060 CWC3260 CWC * 50* 50* 50* 50* 50* 50* 67 27/32 (1723) 69 3/8 (1762) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 63 27/32 (1622) 65 3/8 (1660) 53 7/8 (1368) 59 27/32 (1520) 61 3/8 (1559) 57 27/32 (1469) 59 3/8 (1508) 51 27/32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) CWC1864 CWC2064 CWC2464 CWC2864 CWC3064 CWC3264 CWC3664 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-10

11 1-WID UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 35 3/4 (908) 39 3/4 (1010) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 38 13/16 (986) 42 13/16 (1087) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 32 3/4 (832) 36 3/4 (933) 24 (610) 28 (711) 30 (762) 32 (813) 36 (914) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) 50* 50* 50* 50* 50* 50* 50* 66 3/4 (1695) 66 (1676) CWC1866 CWC2066 CWC2466 CWC2866 CWC3066 CWC3266 CWC * 50* 50* 50* 50* 50* 50* 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 59 7/8 (1581) CWC1872 CWC2072 CWC2472 CWC2872 CWC3072 CWC3272 CWC * 50* 50* 50* 50* 50* 50* 78 3/4 (2000) 78 (1981) 71 7/8 (1826) CWC1878 CWC2078 CWC2478 CWC2878 CWC3078 CWC3278 CWC * 50* 50* 50* 50* 50* 50* 87 27/32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) 81 27/32 (2079) 83 3/8 (2118) 75 27/32 (1926) 77 3/8 (1965) 69 27/32 (1774) 71 3/8 (1813) CWC1884 CWC2084 CWC2484 CWC2884 CWC3084 CWC3284 CWC3684 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-11

12 GNRAL INFORMATION TATIONARY CAMNT DIMNIONAL WINDOW Wood pic casement stationary windows may be specified as dimensional by adjusting the desired rough opening width or height in 1/4 increments from standard. MULTIPL AMBLI Wood pic casement stationary windows may be mulled above, below, or beside other wood casement windows, or other wood window products. Factory assembled mulls are limited in height (100 ), width (150 ), and a total area of 75 square feet. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-12

13 LVATION NOT TATIONARY CAMNT LVATION DRAWING UTILIZ A LIMITD NUMBR OF PROJCTD LIN TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B UD IN A MALL GRAPHICAL CAL. LVATION AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH TRUCTUR. IF MOR DIMNION AR NDD, U TH CTION DRAWING FOR MOR COMPLT DPICTION. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame ize Glass ize 39 27/32 (1012) 41 3/8 (1051) 36 3/4 (933) 36 (914) 29 7/8 (759) 43 3/4 (1111) 46 13/16 (1189) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 50* Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include subsill. (ubtract 1/2 from Masonry Opening for Unit ize) DP RATING CWCP4036 CWP INDICAT WOOD PIC TATIONARY CAMNT TH FIRT TWO NUMBR INDICAT TH UNIT WIDTH BOOK COD TH LAT TWO NUMBR INDICAT TH UNIT HIGHT TANDARD LIT BRAKUP AR HOWN ON ACH LVATION DRAWING GNRAL CAMNT NOT LVATION YMBOL LGND: 1. WOOD PIC CAMNT (CWC) UNIT AR AVAILABL A OPRATING OR FIXD UNIT. 2. CWCP IN A BOOK COD DNOT TH UNIT I A WOOD PIC CAMNT PICTUR (FIXD) UNIT. 3. UNIT LVATION AR HOWN WITH BRICKMOULD AND UBILL. 4. LVATION DRAWING HOW TANDARD LIGHT CUT FOR OR 1 1/8 [29] GRILL BAR OR IMULATD DIVIDD LIT. 5. OPRATING UNIT AR AVAILABL A LFT OR RIGHT HAND OPRATION. 6. DIMNIONAL VALU IN ( ) AR MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. OPRATING UNIT UTILIZ TH R65 LOCKING YTM FOR DP RATING. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-13

14 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 43 3/4 (1111) 46 13/16 (1189) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 45 3/4 (1162) 48 13/16 (1240) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 51 3/4 (1314) 54 13/16 (1392) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) 57 3/4 (1467) 60 13/16 (1545) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) 59 3/4 (1518) 62 13/16 (1595) 56 3/4 (1441) 56 (1422) 49 7/8 (1267) 17 27/32 (453) 19 3/8 (492) 21 27/32 (555) 23 3/8 (568) 23 27/32 (606) 25 3/8 (645) 14 3/4 (375) 14 (356) 7 7/8 (200) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) 13 7/8 (352) 11 7/8 (302) 50* 50* 50* 50* 50* CWCP4014 CWCP4214 CWCP4814 CWCP5414 CWCP * 50* 50* 50* 50* CWCP4018 CWCP4218 CWCP4818 CWCP5418 CWCP * 50* 50* 50* 50* 24 3/4 (629) 24 (610) 17 7/8 (454) 50* 50* 50* 50* 50* 30 3/4 (781) 30 (762) 50* 50* 50* 50* 50* 32 3/4 (832) 32 (813) 50* 50* 50* 50* 50* 36 3/4 (933) 36 (914) 50* 50* 50* 50* 50* 40 3/4 (1035) 40 (1016) 50* 50* 50* 50* 50* 50* 50* 50* 50* 50* 42 3/4 (1086) 42 (1067) CWCP4020 CWCP4220 CWCP4820 CWCP5420 CWCP /32 (707) 29 3/8 (746) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) 33 7/8 (860) 35 7/8 (911) CWCP4024 CWCP4224 CWCP4824 CWCP5424 CWCP /32 (860) 35 3/8 (899) CWCP4030 CWCP4230 CWCP4830 CWCP5430 CWCP /32 (910) 37 3/8 (949) CWCP4032 CWCP4232 CWCP4832 CWCP5432 CWCP /32 (1012) 41 3/8 (1051) CWCP4036 CWCP4236 CWCP4836 CWCP5436 CWCP /32 (1114) 45 3/8 (1153) CWCP4040 CWCP4240 CWCP4840 CWCP5440 CWCP /32 (1164) 47 3/8 (1203) CWCP4042 CWCP4242 CWCP4842 CWCP5442 CWCP5642 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-14

15 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 43 3/4 (1111) 46 13/16 (1189) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 45 3/4 (1162) 48 13/16 (1240) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 51 3/4 (1314) 54 13/16 (1392) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) 57 3/4 (1467) 60 13/16 (1545) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) 59 3/4 (1518) 62 13/16 (1595) 56 3/4 (1441) 56 (1422) 49 7/8 (1267) 50* 50* 50* 50* 50* 50* 50* 50* 50* 50* 54 3/4 (1391) 54 (1372) 50* 50* 50* 50* 50* 56 3/4 (1441) 56 (1422) 50* 50* 50* 50* 50* 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 50* 50* 50* 50* 50* 67 27/32 (1723) 69 3/8 (1762) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 63 27/32 (1622) 65 3/8 (1660) 59 27/32 (1520) 61 3/8 (1559) 49 7/8 (1267) 57 27/32 (1469) 59 3/8 (1508) 47 7/8 (1216) 51 27/32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) CWCP4048 CWCP4248 CWCP4848 CWCP5448 CWCP5648 CWCP4054 CWCP4254 CWCP4854 CWCP5454 CWCP5654 CWCP4056 CWCP4256 CWCP4856 CWCP5456 CWCP5656 CWCP4060 CWCP4260 CWCP4860 CWCP5460 CWCP5660 CWCP4064 CWCP4264 CWCP4864 CWCP5464 CWCP5664 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-15

16 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 43 3/4 (1111) 46 13/16 (1189) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 45 3/4 (1162) 48 13/16 (1240) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 51 3/4 (1314) 54 13/16 (1392) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) 57 3/4 (1467) 60 13/16 (1545) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) 59 3/4 (1518) 62 13/16 (1595) 56 3/4 (1441) 56 (1422) 49 7/8 (1267) 50* 50* 50* 50* 50* 66 3/4 (1695) 66 (1676) 50* 50* 50* 50* 50* 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 59 7/8 (1521) 50* 50* 50* 50* 50* 78 3/4 (2000) 78 (1981) 71 7/8 (1826) 50* 50* 50* 50* 50* 87 27/32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) 81 27/32 (2079) 83 3/8 (2118) 75 27/32 (1926) 77 3/8 (1965) 69 27/32 (1774) 71 3/8 (1813) CWCP4066 CWCP4266 CWCP4866 CWCP5466 CWCP5666 CWCP4072 CWCP4272 CWCP4872 CWCP5472 CWCP5672 CWCP4078 CWCP4278 CWCP4878 CWCP5478 CWCP5678 CWCP4084 CWCP4284 CWCP4884 CWCP5484 CWCP5684 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-16

17 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 63 3/4 (1619) 66 13/16 (1722) 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 67 3/4 (1721) 70 13/16 (1798) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 69 3/4 (1772) 72 13/16 (1849) 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 75 3/4 (1924) 78 13/16 (2001) 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 17 27/32 (453) 19 3/8 (492) 21 27/32 (555) 23 3/8 (568) 23 27/32 (606) 25 3/8 (645) 14 3/4 (375) 14 (356) 7 7/8 (200) 18 3/4 (476) 18 (457) 20 3/4 (527) 20 (508) 13 7/8 (352) 11 7/8 (302) 50* 50* 50* 50* CWCP6014 CWCP6414 CWCP6614 CWCP * 50* 50* 50* CWCPC6018 CWCP6418 CWCP6618 CWCP * 50* 50* 50* CWCP6020 CWCP6420 CWCP6620 CWCP /32 (707) 29 3/8 (746) 24 3/4 (629) 24 (610) 17 7/8 (454) 50* 50* 50* 50* CWCP6024 CWCP6424 CWCP6624 CWCP /32 (860) 35 3/8 (899) 30 3/4 (781) 30 (762) 23 7/8 (607) 50* 50* 50* 50* CWCP6030 CWCP6430 CWCP6630 CWCP /32 (910) 37 3/8 (949) 32 3/4 (832) 32 (813) 25 7/8 (657) 50* 50* 50* 50* CWCP6032 CWCP6432 CWCP6632 CWCP /32 (1012) 41 3/8 (1051) 36 3/4 (933) 36 (914) 29 7/8 (759) 50* 50* 50* 50* CWCP6036 CWCP6436 CWCP6636 CWCP /32 (1114) 45 3/8 (1153) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 50* 50* 50* 50* CWCP6040 CWCP6440 CWCP6640 CWCP /32 (1164) 47 3/8 (1203) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 50* 50* 50* 50* CWCP6042 CWCP6442 CWCP6642 CWCP7242 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-17

18 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 63 3/4 (1619) 66 13/16 (1722) 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 67 3/4 (1721) 70 13/16 (1798) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 69 3/4 (1772) 72 13/16 (1849) 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 75 3/4 (1924) 78 13/16 (2001) 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 50* 50* 50* 50* 50* 50* 50* 50* 54 3/4 (1391) 54 (1372) 50* 50* 50* 50* 56 3/4 (1441) 56 (1422) 50* 50* 50* 50* 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 50* 50* 50* 50* 67 27/32 (1723) 69 3/8 (1762) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 63 27/32 (1622) 65 3/8 (1660) 59 27/32 (1520) 61 3/8 (1559) 49 7/8 (1267) 57 27/32 (1469) 59 3/8 (1508) 47 7/8 (1216) 51 27/32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) CWCP6048 CWCP6448 CWCP6648 CWCP7248 CWCP6054 CWCP6454 CWCP6654 CWCP7254 CWCP6056 CWCP6456 CWCP6656 CWCP7256 CWCP6060 CWCP6460 CWCP6660 CWCP7260 CWCP6064 CWCP6464 CWCP6664 CWCP7264 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-18

19 PICTUR UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 63 3/4 (1619) 66 13/16 (1722) 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 67 3/4 (1721) 70 13/16 (1798) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 69 3/4 (1772) 72 13/16 (1849) 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 75 3/4 (1924) 78 13/16 (2001) 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 50* 50* 50* 50* 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 50* 50* 50* 50* 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 50* 50* 50* 50* 78 3/4 (2000) 78 (1981) 71 7/8 (1826) 50* 50* 50* 50* 87 27/32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) 81 27/32 (2079) 83 3/8 (2118) 75 27/32 (1926) 77 3/8 (1965) 69 27/32 (1774) 71 3/8 (1813) CWCP6066 CWCP6466 CWCP6666 CWCP7266 CWCP6072 CWCP6472 CWCP6672 CWCP7272 CWCP6078 CWCP6478 CWCP6678 CWCP7278 CWCP6084 CWCP6484 CWCP6684 CWCP7284 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. Note: levations shown DO NOT have exterior trim. ubtract 3/4 (19) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-19

20 GNRAL INFORMATION CTOR TOP Wood pic casement sector tops are constructed the same as PIC primed casements, roll formed cladding on wood sash. Wood pic casement sector top windows are available with left or right hand operation (hinged on the springline), or stationary (non-venting). Operating mechanism includes stainless steel, corrosion resistant, butt hinges and single arm roto-type operator with hardened steel gears and operating arm. ash locks are concealed unison type with an exposed locking lever and escutcheon plate. There are several interior hardware finish options. Refer to the pecifications for finish options. PRIMD PIC CAMNT CTOR TOP utilize some of the same options as PRIMD PIC CAMNT. Those options have not been repeated here in this sub-section. ee the PRIMD PIC CAMNT section for: Trim Options (all wood exterior trim is available as radius trim) Unit izing CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-20

21 HANDING, OPRATION & LIMIT DVIC CTOR TOP LFT HAND RIGHT HAND OPRATOR OPRATOR CAMNT UNIT HANDING: UNIT HANDING I DFIND (FROM TH XTRIOR) A TH DIRCTION TH AH OPN. UNIT HANDING INFORMATION: OPRATING INGL CTOR UNIT - MAY B HANDD LFT OR RIGHT. OPRATING TWIN CTOR UNIT - TH UNIT AR HINGD ON TH PRINGLIN ID. TH LFT AH HA LFT HAND OPRATION AND TH RIGHT AH HA RIGHT HAND OPRATION ONLY. OPRATING TRIPL CTOR UNIT - ONLY TH FLANKING UNIT MAY B OPRATOR WHICH AR HINGD ON TH PRINGLIN ID. TH TWO OPRATING AH AR HANDD TH AM A TH TWIN CTOR. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-21

22 LVATION NOT CTOR TOP LVATION DRAWING UTILIZ A LIMITD NUMBR OF PROJCTD LIN TO PRODUC A RUDIMNTARY DRAWING INTNDD TO B UD IN A MALL GRAPHICAL CAL. LVATION AR VIWD PRPNDICULAR FROM TH XTRIOR OF TH TRUCTUR. IF MOR DIMNION AR NDD, U TH CTION DRAWING FOR MOR COMPLT DPICTION. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame ize Glass ize 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements include subsill. (ubtract 1/2 from Masonry Opening for Unit ize) DP RATING 27 27/32 (707) 29 3/8 (746) 24 3/4 (629) 24 (610) 17 7/8 (454) 35* CWC INDICAT WOOD PIC CAMNT CTOR TOP TH FIRT TWO NUMBR INDICAT TH UNIT WIDTH CWC2424 BOOK COD TH LAT TWO NUMBR INDICAT TH UNIT HIGHT GNRAL RADIU CAMNT NOT LVATION YMBOL LGND: 1. UNIT LVATION AR HOWN WITH BRICKMOULD AND UBILL. 2. DIMNIONAL VALU IN ( ) AR MILLIMTR CONVRION. 3. ALL CTOR UNIT AR AVAILABL A OPRATING UNIT. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. ** BAIC UNIT RQUIR LIMIT DVIC ON AH WHN OPRATING. LO UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. TATIONARY UNIT. LIMITD OPRATION. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-22

23 CTOR TOP UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) 33 3/4 (857) 36 13/16 (935) 30 3/4 (781) 30 (762) 23 7/8 (607) M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) 33 3/4 (857) 36 13/16 (935) 30 3/4 (781) 30 (762) 23 7/8 (607) 27 27/32 (707) 29 3/8 (746) 24 3/4 (629) 24 (610) 17 7/8 (454) CWC2424 CWC /32 (1469) 59 3/8 (1508) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) 33 27/32 (860) 35 3/8 (899) 30 3/4 (781) 30 (762) 23 7/8 (607) CWC2454 CWC3054 CWC2430 CWC /32 (910) 37 3/8 (949) 32 3/4 (832) 32 (813) 25 7/8 (657) 59 27/32 (1520) 61 3/8 (1559) 56 3/4 (1441) 56 (1422) 49 7/8 (1267) CWC2432 CWC /32 (1012) 41 3/8 (1051) 36 3/4 (933) 36 (914) 29 7/8 (759) CWC2456 CWC /32 (1114) 45 3/8 (1153) 40 3/4 (1035) 40 (1016) 60 3/4 (1543) 60 (1524) 53 7/8 (1368) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) 51 27/32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) 33 7/8 (860) CWC2436 CWC /32 (1622) 65 3/8 (1660) CWC2460 CWC3060 CWC2440 CWC /32 (1164) 47 3/8 (1203) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 67 27/32 (1723) 69 3/8 (1762) CWC2442 CWC3042 CWC2464 CWC3064 CWC2448 CWC3048 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-23

24 CTOR TOP UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) 33 3/4 (857) 36 13/16 (935) 30 3/4 (781) 30 (762) 23 7/8 (607) 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 78 3/4 (2000) 78 (1981) 71 7/8 (1826) ** 87 27/32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) 81 27/32 (2079) 83 3/8 (2118) 75 27/32 (1926) 77 3/8 (1965) 69 27/32 (1774) 71 3/8 (1813) CWC2466 CWC3066 CWC2472 CWC3072 CWC2478 CWC3078 ** CWC2484 CWC3084 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. ** BAIC UNIT RQUIR LIMIT DVIC ON AH WHN OPRATING. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-24

25 XTNDD HALF ROUND UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 26 13/16 (681) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 20 3/4 (527) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 20 (508) 24 (610) 28 (711) 30 (762) 13 7/8 (352) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 27 27/32 (707) 29 3/8 (746) 24 3/4 (629) 24 (610) 17 7/8 (454) 35* CWCH1824 CWCH2024 CWCH /32 (860) 35 3/8 (899) 30 3/4 (781) 30 (762) 23 7/8 (607) 35* CWCH1830 CWCH2030 CWCH2430 CWCH2830 CWCH /32 (910) 37 3/8 (949) 32 3/4 (832) 32 (813) 25 7/8 (657) 35* CWCH1832 CWCH2032 CWCH2432 CWCH2832 CWCH /32 (1012) 41 3/8 (1051) 36 3/4 (933) 36 (914) 29 7/8 (759) 35* CWCH1836 CWCH2036 CWCH2436 CWCH2836 CWCH /32 (1114) 45 3/8 (1153) 40 3/4 (1035) 40 (1016) 33 7/8 (860) 35* CWCH1840 CWCH2040 CWCH2440 CWCH2840 CWCH /32 (1164) 47 3/8 (1203) 42 3/4 (1086) 42 (1067) 35 7/8 (911) 35* CWCH1842 CWCH2042 CWCH2442 CWCH2842 CWCH /32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) 35* CWCH1848 CWCH2048 CWCH2448 CWCH2848 CWCH3048 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. TATIONARY UNIT. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-25

26 XTNDD HALF ROUND UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 24 (610) 28 (711) 30 (762) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 57 27/32 (1469) 59 3/8 (1508) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) 35* CWCH1854 CWCH2054 CWCH2454 CWCH2854 CWCH * 56 3/4 (1441) 56 (1422) 35* 60 3/4 (1543) 60 (1524) 35* 64 3/4 (1645) 64 (1626) 35* 69 27/32 (1774) 71 3/8 (1813) 66 3/4 (1695) 66 (1676) 59 7/8 (1521) 67 27/32 (1723) 69 3/8 (1762) 57 7/8 (1470) 63 27/32 (1622) 65 3/8 (1660) 53 7/8 (1368) 59 27/32 (1520) 61 3/8 (1559) 49 7/8 (1267) CWCH1856 CWCH2056 CWCH2456 CWCH2856 CWCH3056 CWCH1860 CWCH2060 CWCH2460 CWCH2860 CWCH3060 CWCH1864 CWCH2064 CWCH2464 CWCH2864 CWCH3064 CWCH1866 CWCH2066 CWCH2466 CWCH2866 CWCH3066 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-26

27 XTNDD HALF ROUND UNIT M.O. BRICKMOULD 21 3/4 (552) M.O. ADAM/FLAT CAING 24 13/16 (630) ROUGH OPNING 18 3/4 (476) FRAM IZ 18 (457) DAYLIGHT OPNING 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 31 3/4 (806) 33 3/4 (857) 30 13/16 (783) 34 13/16 (884) 36 13/16 (935) 24 3/4 (629) 28 3/4 (730) 30 3/4 (781) 24 (610) 28 (711) 30 (762) 17 7/8 (454) 21 7/8 (556) 23 7/8 (607) 35* 72 3/4 (1848) 72 (1829) 65 7/8 (1673) 35* 78 3/4 (2000) 78 (1981) 71 7/8 (1826) ** 35* 87 27/32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) 81 27/32 (2079) 83 3/8 (2118) 75 27/32 (1926) 77 3/8 (1965) CWCH1872 CWCH2072 CWCH2472 CWCH2872 CWCH3072 CWCH1878 CWCH2078 CWCH2478 CWCH2878 CWCH3078 ** CWCH1884 CWCH2084 CWCH2484 CWCH2884 CWCH3084 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. UNIT MT GR RQUIRMNT FOR IRC COD. TAT AND LOCAL GR COD MAY DIFFR. ALWAY RFR TO LOCAL BUILDING COD FOR COMPLT RQUIRMNT. CHCK WITH LOCAL OFFICIAL TO NUR COMPLIANC BFOR INTALLING TH UNIT. ** BAIC UNIT RQUIR LIMIT DVIC ON AH WHN OPRATING. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/4 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-27

28 XTNDD QUARTR ROUND UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) 31 3/4 (806) 34 13/16 (884) 28 3/4 (730) 28 (586) 21 7/8 (556) 33 3/4 (857) 36 13/16 (935) 30 3/4 (781) 30 (762) 23 7/8 (607) 33 27/32 (860) 35 3/8 (899) 35 27/32 (910) 37 3/8 (949) 39 27/32 (1012) 41 3/8 (1051) 30 3/4 (781) 30 (762) 32 3/4 (832) 32 (813) 36 3/4 (933) 36 (914) 23 7/8 (607) 25 7/8 (657) 29 7/8 (759) CWCQ1830 CWCQ2030 CWCQ2430 CWCQ1832 CWCQ2032 CWCQ2432 CWCQ1836 CWCQ2036 CWCQ2436 CWCQ2836 CWCQ /32 (1114) 45 3/8 (1153) 40 3/4 (1035) 40 (1016) 33 7/8 (860) CWCQ1840 CWCQ2040 CWCQ2440 CWCQ2840 CWCQ /32 (1164) 45 3/8 (1203) 42 3/4 (1086) 42 (1067) 35 7/8 (911) CWCQ1842 CWCQ2042 CWCQ2442 CWCQ2842 CWCQ /32 (1317) 53 3/8 (1356) 48 3/4 (1238) 48 (1219) 41 7/8 (1064) CWCQ1848 CWCQ2048 CWCQ2448 CWCQ2848 CWCQ /32 (1469) 59 3/8 (1508) 54 3/4 (1391) 54 (1372) 47 7/8 (1216) CWCQ1854 CWCQ2054 CWCQ2454 CWCQ2854 CWCQ /32 (1520) 61 3/8 (1559) 56 3/4 (1441) 56 (1422) 49 7/8 (1267) CWCQ1856 CWCQ2056 CWCQ2456 CWCQ2856 CWCQ /32 (1622) 65 3/8 (1660) 60 3/4 (1543) 60 (1524) 53 7/8 (1368) CWCQ1860 CWCQ2060 CWCQ2460 CWCQ2860 CWCQ /32 (1723) 69 3/8 (1762) 64 3/4 (1645) 64 (1626) 57 7/8 (1470) CWCQ1864 CWCQ2064 CWCQ2464 CWCQ2864 CWCQ3064 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. TATIONARY UNIT. Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/8 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-28

29 XTNDD QUARTR ROUND UNIT M.O. BRICKMOULD M.O. ADAM/FLAT CAING ROUGH OPNING FRAM IZ DAYLIGHT OPNING 21 3/4 (552) 24 13/16 (630) 18 3/4 (476) 18 (457) 11 7/8 (302) 23 3/4 (603) 26 13/16 (681) 20 3/4 (527) 20 (508) 13 7/8 (352) 27 3/4 (705) 30 13/16 (783) 24 3/4 (629) 24 (610) 17 7/8 (454) 31 3/4 (806) 34 13/16 (884) 28 3/4 (730) 28 (586) 21 7/8 (556) 33 3/4 (857) 36 13/16 (935) 30 3/4 (781) 30 (762) 23 7/8 (607) 69 27/32 (1774) 71 3/8 (1813) 66 3/4 (1695) 66 (1676) 59 7/8 (1520) CWCQ1866 CWCQ2066 CWCQ2466 CWCQ2866 CWCQ /32 (1926) 77 3/8 (1965) 72 3/4 (1848) 72 (1829) 65 7/8 (1673) CWCQ1872 CWCQ2072 CWCQ2472 CWCQ2872 CWCQ /32 (2079) 83 3/8 (2118) 78 3/4 (2000) 78 (1981) 71 7/8 (1826) CWCQ1878 CWCQ2078 CWCQ2478 CWCQ2878 CWCQ /32 (2231) 89 3/8 (2270) 84 3/4 (2153) 84 (2134) 77 7/8 (1978) LO LO CWCQ1884 CWCQ2084 CWCQ2484 LVATION YMBOL LGND: M.O. = MAONRY OPNING VALU IN () AR IN MILLIMTR CONVRION. ##* NUMBR INDICAT DIGN PRUR (DP) RATING WITH TANDARD GLAZING. TATIONARY UNIT. LO LIMITD OPRATION. CWCQ2884 CWCQ3084 Note: levations shown DO NOT have exterior trim. ubtract 1/2 (12.7) from M.O. (Masonry Opening) for Unit izes. Masonry Openings above include ill Nose, see Trim Options page for ill Nose specifications. For other Trim Options refer to the Unit izing, Rough Opening & Masonry Openings page. CAL: 1/8 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-29

30 GLAZING OPTION CAMNT INTRIOR GLAZD INULATD 3/4 [19] GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL BAR (PUTTY/BAD) 7/8 DL BAR (PUTTY/BAD) 11/8 DLBAR (PUTTY/BAD) 5/8 [16] 5/8 DL BAR 7/8 DL BAR 11/8 DLBAR 13/8 [35] 2 5/16 [59] 7/8 DL BAR (BAD TOP) 11/8 DLBAR (BAD TOP) 13/8 DLBAR (BAD TOP) 2 5/16 DL BAR (BAD TOP) 3/16 [5] 7/32 [6] 5/16 [8] 5/8 [16] 23/32 [18] 1 [25] 5/8 FLAT GBG 23/32 CONTOUR GBG 1 CONTOUR GBG CAL: NT November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-30

31 GLAZING OPTION CAMNT INTRIOR GLAZD INGL GLAZD 1/8 [3] GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-31

32 GLAZING OPTION CAMNT INTRIOR GLAZD IMPACT RITANT GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-32

33 GLAZING OPTION TATIONARY CAMNT INTRIOR GLAZD INULATD 3/4 [19] GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL BAR (PUTTY/BAD) 7/8 DL BAR (PUTTY/BAD) 11/8 DLBAR (PUTTY/BAD) 5/8 [16] 5/8 DL BAR 7/8 DL BAR 11/8 DLBAR 13/8 [35] 2 5/16 [59] 7/8 DL BAR (BAD TOP) 11/8 DLBAR (BAD TOP) 13/8 DLBAR (BAD TOP) 2 5/16 DL BAR (BAD TOP) 3/16 [5] 7/32 [6] 5/16 [8] 5/8 [16] 23/32 [18] 1 [25] 5/8 FLAT GBG 23/32 CONTOUR GBG 1 CONTOUR GBG CAL: NT November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-33

34 GLAZING OPTION TATIONARY CAMNT INTRIOR GLAZD INGL GLAZD 1/8 [3] GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-34

35 GLAZING OPTION TATIONARY CAMNT INTRIOR GLAZD IMPACT RITANT GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-35

36 GLAZING OPTION CTOR TOP CAMNT INTRIOR GLAZD INULATD 15/16 [24} GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL BAR (PUTTY/BAD) 7/8 DL BAR (PUTTY/BAD) 11/8 DLBAR (PUTTY/BAD) 5/8 [16] 5/8 DL BAR 7/8 DL BAR 11/8 DLBAR 13/8 [35] 2 5/16 [59] 7/8 DL BAR (BAD TOP) 11/8 DLBAR (BAD TOP) 13/8 DLBAR (BAD TOP) 2 5/16 DL BAR (BAD TOP) 3/16 [5] 7/32 [6] 5/16 [8] 5/8 [16] 23/32 [18] 1 [25] 5/8 FLAT GBG 23/32 CONTOUR GBG 1 CONTOUR GBG CAL: NT November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-36

37 GLAZING OPTION CTOR TOP CAMNT INTRIOR GLAZD INGL GLAZD 1/8 [3] GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-37

38 GLAZING OPTION CTOR TOP CAMNT INTRIOR GLAZD IMPACT RITANT GLA 13/8 [35] 7/8 GRILL BAR 1 1/8 GRILL BAR 1 3/8 GRILL BAR 5/8 [16] 5/8 DL (PUTTY/BAD) 7/8 DL (PUTTY/BAD) 11/8 DL (PUTTY/BAD) 5/8 [16] 5/8 DL 7/8 DL 11/8 DL 13/8 [35] 2 5/16 [59] 7/8 DL (BAD TOP) 11/8 DL (BAD TOP) 13/8 DL (BAD TOP) 2 5/16 DL BAR (BAD TOP) CAL: 3 = 1 November 2013 JLD-WN reserves the right to change specifications without notice. Page 4-38

39 TRIM OPTION CAMNT WOOD XTRIOR TRIM 1 5/32 [29] 1 5/32 [29] 1 5/32 [29] 1 31/32 [50] 13/8 [35] 31/2 [89] 2 29/32 [74] 31/2 [89] 2 29/32 [74] BRICKMOULD 31/2 FLAT CAING ADAM CAING 1 5/32 [29] 1 5/32 [29] 1 7/32 [31] 5 1/2 [140] 4 29/32 [125] 4 1/2 [114] 3 29/32 [99] 4 1/2 [114] 3 29/32 [99] 51/2 FLAT CAING 41/2 FLAT CAING 1X4 BACKBAND CAING WOOD UBILL OPTION 11/4 [32] 2 7/32 [57] 1 15/32 [37] 3 [76] 2 11/32 [59] 3 [76] WOOD UBILL WOOD HITORICAL UBILL CAL: 3 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-39

40 TRIM OPTION TATIONARY CAMNT WOOD XTRIOR TRIM 1 5/32 [29] 1 5/32 [29] 1 5/32 [29] 1 31/32 [50] 13/8 [35] 31/2 [89] 2 29/32 [74] 31/2 [89] 2 29/32 [74] BRICKMOULD 31/2 FLAT CAING ADAM CAING 1 5/32 [29] 1 5/32 [29] 1 7/32 [31] 5 1/2 [140] 4 29/32 [125] 4 1/2 [114] 3 29/32 [99] 4 1/2 [114] 3 29/32 [99] 51/2 FLAT CAING 41/2 FLAT CAING 1X4 BACKBAND CAING WOOD UBILL OPTION 11/4 [32] 2 7/32 [57] 1 15/32 [37] 3 [76] 2 11/32 [59] 3 [76] WOOD UBILL WOOD HITORICAL UBILL CAL: 3 = 1 December 2011 JLD-WN reserves the right to change specifications without notice. Page 4-40