HURRICANESHIELD IMPACT-RESISTANT GLASS SECTION DIRECTORY. Size and performance summary. Glazing performance. Grille profiles and patterns.

Transcription

1 ECTIN DIRECTRY ize and performance summary Glazing performance Grille profiles and patterns ize tables Design Data Detailed Product Description Cross sections The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are subject to change without notice. Consult your local Pella representative for up-to-date product information. CM-HIG-1

2 BRAND UMMARY Pella 350 eries Casement windows feature extruded, rigid PVC (polyvinyl chloride) frames and sash with heat-fused mitered corners for a fully welded corner assembly. The mootheam welded corners on the interior of the sash are virtually invisible. Casement windows meet industry standards for water infiltration and wind resistance and meet ENERGY TAR guidelines with dual-pane insulated glass. BLCK FRAME DEIGN 4- Block 4- block frame can be used in new construction block or concrete walls. They may also be used in replacement of old aluminum or steel frame windows or pocket replacement into wood frames from the exterior. The block frames include interior and exterior accessory grooves. Custom sizes are available in 1/8" increments for a perfect fit. 4- Block Frame DUBLE-WALL FLUH FLANGE Replacement Frame Design The flush flange frame allows for easy replacement of old aluminum or steel frame windows without removing the existing frame head or jambs typically used with stucco exteriors in southwest arid climates. The frame depth is 4- (overall wall depth of 4-1/16") includes interior accessory groove. Custom sizes are available in 1/8" increments for a perfect fit. NAIL FIN FRAME DEIGN With or Without Integrated J-Channel Continuous fin with welded corners adds a protective weather barrier and allows for hassle-free installation. The standard 4- frame depth includes interior and exterior accessory grooves. Nailing fin has a 1-7/16" setback from exterior face of window frame. Custom sizes are available in 1/8" increments for a perfect fit. 4-9/16" and 6-9/16" factory applied primed or clear jamb extensions are available. INTEGRAL 5/8" FLANGE FRAME The integral 5/8" flange frame can be used in new construction block or concrete walls. Commonly used in Florida and often referred to as "Florida Flange" frame. The frame depth is 4- (overall wall depth of 3-7/8") includes interior accessory groove. Custom sizes are available in 1/8" increments for a perfect fit. With J-Channel Without J-Channel CM-HIG-2

3 PRDUCT ELECTIN GUIDE ize and Performance Data, ound Transmission Class IZE tandard izes pecial izes Available Built on 1/8" Increments FRAME Nail Fin nly Nail Fin with J-Channel 4- Block Double-Wall Flush Flange Integral 5/8" Flange PERFRMANCE 1 tandard Performance Meets or Exceeds AAMA/WDMA Ratings CW-PG70 Hallmark Certified Air Infiltration (cfm / ft 2 of 1.57 psf wind pressure.) 0.05 Design Pressure 70 psf Water Penetration Resistance psf ther Performance Criteria Forced Entry Resistance (Minimum ecurity Grade) 2 40 Maximum perating Force (lbs) (Initiate Motion / Maintain Motion) 15/6 Certification Results 1 Product Design Pressure Large Missile Rating D Minimum Maximum Hallmark Certified Miami-Dade County Approved (NA) Florida Product Approval ystem (FPA) Texas Department of Insurance (TDI) VENT UNIT 1" Insulated Glass PVB + 70 / / H FL16053 WIN-1773 UND TRANMIIN CLA AND UTDR-INDR TRANMIIN CLA Frame ize Tested 3 verall Glazing Thickness Exterior Glass Thickness Glazing ystem Interior Glass Thickness Third Pane Thickness TC Rating ITC Rating HURRICANEHIELD IMPACT-REITANT LAMINATED INULATING GLA 24" x 60" 1" 3mm 9mm PVB " x 60" 1" 5mm 9mm PVB = tandard; = ptional; ( ) = Not Available (1) Published performance data is for single unit only. ee Design Data pages in this section for specific product performance class and grade values. (2) The higher the level, the greater the product's abilbity to resist forced entry. (3) ATM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration. The presence of low-e or argon have negligible effect on sound attenuation characteristics. CM-HIG-3

4 PRDUCT ELECTIN GUIDE Features and ptions GLAZING (INULATING GLA) Glazing Type Dual-pane impact-resistant insulating glass Insulated Glass ptions / Low-E Types Advanced Low-E undefense Low-E Gray Low-E Bronze-tinted Advanced Low-E Additional Glazing ptions Annealed glass Tempered glass paque glass 1 Gas Fill / High Altitude Argon High altitude INTERIR / EXTERIR CLR White Interior/White Exterior Almond Interior/Almond Exterior White Interior/Brown Exterior White Interior/Fossil Exterior White Interior/Black Exterior White Interior/Brick Red Exterior White Interior/Hartford Green Exterior White Interior/Morning ky Gray Exterior White Interior/Poplar White Exterior White Interior/Portobello Exterior White Interior/Tan Exterior HARDWARE Color matched hardware Bright Brass, atin Nickel or il-rubbed Bronze CREEN Conventional black fiberglass screens - flat InView screens GRILLE Grilles-Between-the-Glass Contour 1" Contour Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided imulated-divided-light Grilles 1 (without spacer) 7/8" contour profile Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided = tandard; = ptional (1) Contact your local Pella sales representative for current offering. CM-HIG-4

5 GLAZING PERFRMANCE - TTAL UNIT 1" Impact-Resistant Insulating Glass Glass Thickness NFRC Certified Product # Glass (mm) Gap Fill U-Factor Performance Values 1 HGC VLT CR haded Areas Meet ENERGY TAR Performance Criteria in Zones hown Type of Glazing U.. Canada 2 Ext. Int. Zone ER Zone VENT N NC C " Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N VENT WITH BCURE GLAZING 1" Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " undefense Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N R-Value = 1/U-Factor HGC = olar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY TAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY TAR 2015 initiative. Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown. ee the Product Performance section for more detailed information or visit for Energy tar guidelines. Rev. 01/03/2019 CM-HIG-5

6 GLAZING PERFRMANCE - TTAL UNIT 1" Impact-Resistant Insulating Glass Glass Thickness NFRC Certified Product # Glass (mm) Gap Fill U-Factor Performance Values 1 HGC VLT CR haded Areas Meet ENERGY TAR Performance Criteria in Zones hown Type of Glazing U.. Canada 2 Ext. Int. Zone ER Zone VENT N NC C " Bronze Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Bronze Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Gray Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Gray Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Bronze Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Bronze Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Gray Advanced Low-E IG PVB PEL-N air with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N " Gray Advanced Low-E IG PVB PEL-N argon with or 1" grilles-between-the-glass PEL-N with 7/8" imulated Divided Light grilles PEL-N R-Value = 1/U-Factor HGC = olar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY TAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY TAR 2015 initiative. Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown. ee the Product Performance section for more detailed information or visit for Energy tar guidelines. CM-HIG-6

7 GRILLE TYPE Grille Profiles HURRICANEHIELD Grilles-Between-the-Glass Impact-Resistant Glazing imulated Divided Light 1" 7/8" Contour GBG 1" Contour GBG 7/8" DL Grille Patterns PRAIRIE LITE PATTERN Prairie - Approximately 4" from edge of sash to center of bar - Minimum actual glass is 13" 9-Lite Prairie THER AVAILABLE PATTERN Traditional - pecify number of lites. - Grilles must be equally divided on visible glass. - Minimum 6" x 6". Traditional Top Row Custom Equally Divided Top Row - tandard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller. For traditional patterns, see size tables. CM-HIG-7

8 PECIAL IZE FRAME DIMENIN Miscellaneous Formulas 1-WIDE VENT UNIT MINIMUM 13- W x 17- H (343 x 445) MAXIMUM 35- W x 71- H (889 x 1 803) General Notes: To convert areas to square meters (m 2 ), multiply square feet by Rough pening = Frame Dimension +. Unit Height must be > Unit Width Keep frame di men sions to the near est 1/8" increment. Tempered glass must measure 18- diagonally. If glass width to height ratio is > 5 to 1, then unit must be tempered. Miscellaneous Formulas 1-WIDE VENT VIIBLE GLA ACTUAL GLA VGW = FW 7" VGH = FH 7" AGW = FW 5-7/8" AGH = FH 5-7/8" VENT AREA [(FH - 5.5) x (CW - 2.5)] / 144 Clear pening Formulas 1-WIDE VENT IDE PIVT HARDWARE TANDARD HARDWARE HEAVY DUTY HARDWARE ((FH-5.5) x CW) /144 ((FH-5.5) x (CW )) /144 ((FH-5.5) x (CW )) /144 KEY: AGW = Actual Glass Width AGH = Actual Glass Height FW = Frame Width FH = Frame Height VGW = Visible Glass Width VGH = Visible Glass Height CW = Clear opening width CH = Clear opening height ide pivot hardware only available on frame widths of 28" to 32" The clear opening formulas do not apply to units with FW < CM-HIG-8

9 IZE TABLE 1-Wide Vent (457) (610) (711) (445) (597) (699) (762) (749) (813) (800) (914) (902) pening 1' 6" Frame 17 2' 0" 23 2' 4" 27 2' 6" 29 2' 8" 31 3' 0" 35 (762) (749) (1 067) (914) (1 054) (902) (1 219) (1 207) (1 372) (1 359) (1 524) (1 511) (1 676) (1 664) (1 829) (1 816) 3' 6" 3' 0" 2' 6" 4' 0" 4' 6" 5' 0" 5' 6" 6' 0" 29 1 /2" 65 1 /2 " 59 1 /2 " 53 1 /2 " 47 1 /2 " 41 1 /2 " 35 1/2 " / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /5-6 E E E E E 1-6/ / / / / /6-0 E Egress Notes: Check all applicable local codes for emergency egress requirements. E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2. Not to scale. CM-HIG-9

10 DEIGN DATA VENT UNIT Call ut Egress Width (Inches) Frame Height (Inches) Width (Inches) Clear pening (Vent Units nly) Height (Inches) Vent Area Ft 2 Egress Notes: Check all applicable local codes for emergency egress requirements. E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. To convert areas to square meters (m²), multiply square feet by Visible Glass Ft 2 Frame Area Ft 2 Design Pressure (tructural nly) Performance Class & Grade 1 1-6/ /2 29-1/2 5-11/ / -75 CW70 1-6/ /2 35-1/2 5-11/ / -75 CW70 1-6/ /2 41-1/2 5-11/ / -75 CW70 1-6/ /2 47-1/2 5-11/ / -75 CW70 1-6/ /2 53-1/2 5-11/ / -75 CW70 1-6/ /2 59-1/2 5-11/ / -75 CW70 1-6/ /2 65-1/2 5-11/ / -75 CW70 1-6/ /2 71-1/2 5-11/ / -75 CW70 2-0/ /2 29-1/ / / -75 CW70 2-0/ /2 35-1/ / / -75 CW70 2-0/ /2 41-1/ / / -75 CW70 2-0/ /2 47-1/ / / -75 CW70 2-0/ /2 53-1/ / / -75 CW70 2-0/ /2 59-1/ / / -75 CW70 2-0/ /2 65-1/ / / -75 CW70 2-0/ /2 71-1/ / / -75 CW70 2-4/ /2 29-1/ / / -75 CW70 2-4/ /2 35-1/ / / -75 CW70 2-4/ /2 41-1/ / / -75 CW70 2-4/ /2 47-1/ / / -75 CW70 2-4/ /2 53-1/ / / -75 CW70 2-4/ /2 59-1/ / / -75 CW70 2-4/ /2 65-1/ / / -75 CW70 2-4/ /2 71-1/ / / -75 CW70 2-6/ /2 29-1/ / / -75 CW70 2-6/ /2 35-1/ / / -75 CW70 2-6/ /2 41-1/ / / -75 CW70 2-6/ /2 47-1/ / / -75 CW70 2-6/ /2 53-1/ / / -75 CW70 2-6/ /2 59-1/ / / -75 CW70 2-6/ /2 65-1/ / / -75 CW70 2-6/ /2 71-1/ / / -75 CW70 2-8/ /2 35-1/ / / -75 CW70 2-8/ /2 41-1/ / / -75 CW70 2-8/ /2 47-1/ / / -75 CW70 2-8/ /2 53-1/ / / -75 CW70 2-8/ /2 59-1/ / / -75 CW70 2-8/ /2 65-1/ / / -75 CW70 2-8/ /2 71-1/ / / -75 CW70 3-0/ /2 35-1/ / / -75 CW70 3-0/3-6 E 35-1/2 41-1/ / / -75 CW70 3-0/4-0 E 35-1/2 47-1/ / / -75 CW70 3-0/4-6 E 35-1/2 53-1/ / / -75 CW70 3-0/5-0 E 35-1/2 59-1/ / / -75 CW70 3-0/5-6 E 35-1/2 65-1/ / / -75 CW70 3-0/6-0 E 35-1/2 71-1/ / / -75 CW70 Ft 2 (1) Maximum performance when glazed with the appropriate glass thickness. Refer to the Product Performance section in election and olutions for more information. CM-HIG-10

11 DETAILED PRDUCT DECRIPTIN FRAME verall frame depth: 4- on all frame types. Frame members are mitered and heat fused to provide a fully welded corner assembly with mootheam virtually invisible interior welds. Frame: [1-7/16" setback nail fin for 3-1/16" wall depth] [Block frame for 4- wall depth] [Flush flange for 4" wall depth] [Integral flange for 3-7/8" wall depth]. Interior and exterior frame surfaces are extruded rigid PVC. AH ash members are extruded, rigid PVC. Panel members are mitered and heat-fused to provide a fully welded corner assembly with mootheam virtually invisible interior welds. Contains sealed insulating glass. WEATHERTRIPPING Vent is weather stripped around the sash with rainstrip and the frame perimeter is weather stripped with an extruded bulb weatherstrip in two locations. GLAZING YTEM Quality float glass complying with ATM C Exterior face-glazed sealed, impact-resistant insulating glass. ilicone-glazed 1" dual-pane impact-resistant insulating glass PVB. Laminated [clear] [Bronze 2] [paque 3] interior light. [Tempered] [Annealed] exterior light is [Advanced Low-E coated [with argon]] [undefense Low-E coated [with argon]] [Gray Low-E coated with argon] [High Altitude 1]]. INTERIR / EXTERIR Window frame and sash members are [[White] [Almond] with integral color extruded throughout the profiles] [[Brown] [Black] [Brick Red] [Hartford Green] [Morning ky Gray] [Poplar White] [Portobello] [Tan] [Fossil] exterior, consisting of a solar reflective coating exceeding AAMA 613 test requirements, with White integral color extruded throughout the profiles on the interior]. All exposed PVC surfaces are smooth, glossy and uniform in appearance. HARDWARE Multipoint unison lock with single handle is factory-installed zinc die cast. Lock tie-bars are stainless steel. High quality stainless steel dual-arm roto operator with fold down crank handle on sill. Hinge arms are stainless steel. Corrosion-resistant fasteners of PVC-compatible material. Hardware finish [White] [Almond] [Bright Brass] [atin Nickel] [il-rubbed Bronze]. CREEN tandard creen Black vinyl coated 18 / 14 mesh fiberglass screen cloth complying with ATM D 3656 and MA et in aluminum extruded frame and fitted to interior of window. Insect screen frame finish is baked enamel, color to match interior. -or- InView creens Vinyl-coated 18/18 mesh fiberglass screen cloth complying with MA 1201, set in aluminum extruded frame fitted to inside of window, supplied complete with all necessary hardware. Insect screen frame finish is baked enamel, color to match interior. PTINAL PRDUCT Grilles Grilles-Between-the-Glass Insulating glass contains [] [1"] contoured aluminum grilles permanently installed between two panes of glass. Patterns are [Traditional] [9-Lite Prairie] [Top Row] [Custom Equally Divided]. Interior grille color matches interior frame. Exterior grille color [ Grille is [White] [Almond 4] [Brown] [Black] [Brick Red] [Hartford Green] [Morning ky Gray] [Poplar White] [Portobello] [Tan] [Fossil]] [1" Grille is [White] [Almond 4] [Brown]]. imulated-divided-light grilles without spacer 7/8" Grilles permanently bonded to the interior and exterior of glass. Patterns are [Traditional] [9-Lite Prairie] [Top Row] [Custom Equally Divided]. Grilles match color of interior and exterior frame Hardware ptional limited opening hardware available for vent units in stainless steel; nominal 3" opening. ptional window opening control device available for field installation. Device allows window to open less than 4 with normal operation, with a release mechanism that allows the sash to open completely. Complies with ATM F (1) Dual Pane IG High Altitude glazing is available without Argon. (2) Bronze glass not available with undefense or Gray Low-E. (3) paque glass not available with Gray Low-E. (4) Almond grilles only available on almond units. Almond units with grilles will have an almond grille color. Rev. 06/26/2018 CM-HIG-11

12 UNIT ECTIN Installation Types 1 7/16" [37] 3 1/16" [78] 4 AW [114] 1 [44] TANDARD BLCK FRAME [19] 1 1/4" [32] TANDARD NAIL FIN 2 [63] [19] 2 [63] 1 1/4" [32] [19] 2 [63] 2 [63] 2 [63] 13/16" [21] 7/8" [22] 3 1/16" [78] 5/8" [16] 5/8" [17] 3 7/8" [98] [19] 7/16" [11] 4 1/16" [103] 3 2 1/4" [57] 3 1 1/4" [32] [19] 3 [19] 1 [44] 1 1/4" [32] 3 3 BLCK FRAME with 5/8" INTEGRAL FLANGE NAIL FIN with J-CHANNEL DUBLE WALL FLUH FLANGE 1 1/4" [32] cale 3" = 1' 0" All dimensions are approximate. CM-HIG-12

13 UNIT ECTIN tandard Nail Fin H 4 AW [114] LJ H HEAD FRAME HEIGHT 2 3/8" [60] ILL ptional Factory Applied Wood Jamb Extensions 1 [38] 3 5/8" [16] 4 9/16" 6 9/16" 3 2 1/4" [57] 1 1/4" [32] 1 7/16" [37] 2 3/8" [60] 3 1/16" [78] [20] 2 [69] 1 [44] HJ 3 1 7/16" [37] 3 1/16" [78] 4 9/16" [116] 6 9/16" [167] 1 [44] HJ HINGE JAMB FRAME WIDTH LJ LCK JAMB 1 [44] cale 3" = 1' 0" All dimensions are approximate. CM-HIG-13