DCG Commercial Tons Packaged Gas / Electric Units

Transcription

1 DG ommercial - Tons Packaged Gas / Electric Units Tons ooling apacity: 80,000 BTU/h 0 Tons ooling apacity: 0,000 BTU/h Tons ooling apacity: 90,000 BTU/h Tons Heating apacity: 0,000 BTU/h 0 Tons Heating apacity: 00,000 BTU/h Tons Heating apacity: 00,000 BTU/h ontents Nomenclature... Product Specifications... Expanded ooling Data... Airflow Data... rankcase Heater... Electrical Data... Dimensions... Wiring Diagrams... for Models with DD ontrols...8 Accessories... Standard Features Patented tubular heat exchanger High-efficiency scroll compressor Aluminum micro-channel indoor coil on -ton units -ton units contain two outdoor fans opper tube / aluminum fin coils High- and low-pressure switches High-capacity, steel-cased filter drier -volt terminal strip ontactor with lugs Units meet the performance outlined in Table.8.- of ASHRAE Standard AHRI ertified; ETL Listed abinet Features Heavy-gauge, galvanized-steel cabinet with UV-resistant powder-paint finish ondenser hail guards Full perimeter rail Built-in filter rack with standard " filters (convertible to " filters) Sloped drain pan * omplete warranty details available from your local dealer or at SS-DG / Supersedes 9/

2 Nomenclature D G B * * * A *,,,8,9 0 Revision Levels Major & Minor Brand Factory-Installed Options D Daikin X No Options A Non-powered convenience outlet onfiguration B Powered convenience outlet Standard Efficiency ( - Tons) Low-ambient kit S Standard Efficiency ( - Tons) D Return air smoke detector T High Efficiency ( - Tons) E Supply air smoke detector F Non-powered convenience outlet; Application Low-ambient kit ooling G Non-powered convenience outlet; G Gas Heat Return air smoke detector H Heat Pump H Non-powered convenience outlet; Supply air smoke detector Nominal ooling apacity J Non-powered convenience outlet; 0 Tons 0 8½ Tons 00 Tons Return & Supply air smoke detectors 08 Tons 0 0 Tons K Non-powered convenience outlet; 00 Tons 0 ½ tons Low-ambient kit; Supply air smoke detector 0 Tons 80 Tons L Non-powered convenience outlet; 090 ½ Tons 0 0 Tons Low-ambient kit Return & Supply air smoke detectors Nominal Heating apacity M Powered convenience outlet; Gas/Electric A/ H/P Factory-Installed Electric Heat Low-ambient kit 0,000 BTU/h XXX No Heat N Powered convenience outlet; ,000 BTU/h 00 0 kw 00 0 kw Return air smoke detector,000 BTU/h 0 kw 0 0 kw O Powered convenience outlet; 0 0,000 BTU/h 0 kw 0 kw Return & Supply air smoke detectors 0 0,000 BTU/h 08 8 kw 0 kw P Powered convenience outlet; 0 0,000 BTU/h 00 0 kw 00 0 kw Supply air smoke detector 00 00,000 BTU/h 0 kw Q Powered convenience outlet; Low-ambient See product specifications for heat size(s) available for each capacity. kit; Return air smoke detector R Powered convenience outlet; Low-ambient Voltage kit; Supply air smoke detector 08-0//0 0//0 T Powered convenience outlet; Low-ambient 08-0//0 //0 kit; Return & Supply air smoke detectors U Non-powered convenience outlet; Supply Fan/Drive Type/Motor Low-ambient kit; Return air smoke detector D Direct Drive (- Tons) V Low-ambient kit; Return air smoke detector V Two-Speed Belt Drive (also designates -Ton with two-stage compressor) W Low-ambient kit; Supply air smoke detector W High Static (two-speed Belt Drive) Y Low-ambient kit; Return & Supply air smoke detectors Factory-Installed Options Z Return & Supply air smoke detectors A Ultra Low-Leak Downflow Economizer R Ultra Low-Leak Downflow Economizer; B DD-BAnet protocol DD-BAnet protocol; Factory-Installed Options F Ultra Low-Leak Downflow Economizer; Disconnect Switch (non-fused) X Standard Aluminized Heat Exchanger DD-BAnet protocol V Low-Leak Downflow Economizer S Stainless-Steel Heat Exchanger H Disconnect Switch (non-fused) W Low-Leak Downflow Economizer D Hinged Panels J Ultra Low-Leak Downflow Economizer; Disconnect Switch (non-fused) K Stainless-Steel Heat Exchanger; Disconnect Switch (non-fused) X No Options Hinged Panels M Disconnect Switch (non-fused); DD-BAnet protocol B Phase Monitor J Stainless Steel Heat Exchanger; Phase Monitor Note: Not all options available for all products. M Hinged Panel; Phase Monitor X= No Options in character th L Stainless-Steel Heat Exchanger; Hinged Panels; Phase Monitor SS-DG

3 Nomenclature Factory-Installed Options Stainless-Steel Heat Exchanger (Gas units only): A tubular heat exchanger made of 09-type stainless steel is installed in the unit. Low-Ambient Kit: Allows for cooling operation at lower outdoor temperatures. On the - to -ton units, cooling operation is extended from 0 F ambient temperature to F outside air temperature. On ½ -0 ton units, cooling operation is extended from F ambient temperature to 0 F outside air temperature. For ton units, cooling operation is extended from F ambient temperature to 0 F outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (A and heat pump units only): Available in all voltage options. Non-powered onvenience Outlet: A 0V, A, GFI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 0V, A, GFI outlet powered with a transformer built into the unit. When a factory-installed powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by.a/.a for 08/0V units, increase by.a for 0V units, and by.a for V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (non-fused; -phase units only): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning (DS units) and heat pump models (DSH units), the appropriate electric heat kit must be ordered to be factory-installed along with the disconnect switch (non-fused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (non-fused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (non-fused) is in the off position. Return Air and/or Supply Air Smoke Detectors: Return air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all units. Two-speed indoor fan blower models are standard on, ½, 8½, 0, ½,, 0 & ton units. Section...0.b of ASHRAE Standard and Section...a of ASHRAE Standard require a minimum of two fan speeds. Section 0.(m) of alifornia Energy ommission Title 0 contains a similar provision. When the units with the two-speed indoor fan blowers operate on a call for the first stage of cooling, the fan operates at low speed, which is % of full speed. When the units operate on a call for the second stage of cooling, the fan operates at full speed. In heating operation, the fan operates at full speed. During ventilation operation, the fan operates at low speed. Phase Monitor: Phase monitor ( phase only), available for - ton DS, D and DT series models. Phase monitor shall provide protection for motors and compressors against problems caused by phase loss, phase reversal and phase unbalance. Phase monitor is equipped with an LED that provides an ON or FAULT indicator. DD ontroller: DD communicating controller, available for - ton DS, D and DT series models with on-board BAnet communication interface. High static blower assembly, factory-installed SS-DG

4 Product Specifications Tons DG80 0V***A* DG80 0V***A* DG80 0V***A* ooling apacity Total, BTU/h 80,000 80,000 80,000 Sensible BTU/h,00,00,00 EER / IEER 0.8 /. 0.8 /. 0.8 /. Decibels AHRI Reference #s Heating apacity High Input/Output (KBTU/h) 0 / 80 0 / 80 0 / 80 Low Input/Output (KBTU/h). / 0. / 0. / 0 Steady State Efficiency (%) Temperature Rise: High / Low ( F) 0-0 / / / 0-0 No. of Burners Evaporator Motor / oil Motor Type (Belt Drive) -speed Belt Drive -speed Belt Drive -speed Belt Drive Indoor Nominal FM,00,00,00 Indoor Motor FLA (ooling).. Horsepower - RPM.0 -,/8.0 -,/8.0 -,0/8 Metering Device TXV TXV TXV Filter Size (#) 0 x x () 0 x x () 0 x x () Drain Size (NPT) R-0A Refrigerant harge ir # R-0A Refrigerant harge ir # Evaporator oil Face Area (ft²) Rows Deep / Fins per Inch / / / Belt Drive Evap Fan Data # of Wheels (D x W) ( x ) ( x ) ( x ) Motor Sheave VP0 x ⅜ VP0 x ⅜ VP0 x ⅜ Blower Sheave 0 x ³/₁₆ 0 x ³/₁₆ 0 x ³/₁₆ Belt BX8 BX8 BX8 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - RPM ⅓ -,0 ⅓ -,0 ⅓ -,0 Fan Diameter / # Fan Blades / / / Outdoor Nominal FM 9,000 9,000 9,000 Face Area (ft²)... Rows Deep / Fins per Inch / / / ompressor Quantity / Type / Scroll / Scroll / Scroll ompressor RLA / LRA IR. # /. / / 8 ompressor RLA / LRA IR. # /. / / 8 Electrical Data Voltage / Phase / Frequency 08/ Standard Max Static... Outdoor Fan FLA / LRA.0/. 0.8 /. 0. /.8 Total Unit Amps Min. ircuit Ampacity¹. /... Max. Overcurrent Protection (amps)² 00 / 00 Entrance Power Supply ⅛ ⅛ ⅛ Entrance ontrol Voltage ⅞ ⅞ ⅞ Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-DG

5 Product Specifications 0 Tons DG0 00V***B* DG0 00V***B* DG0 00V***B* ooling apacity Total, BTU/h 0,000 0,000 0,000 Sensible BTU/h 0,000 0,000 0,000 EER / IEER 9.8 /. 9.8 /. 9.8 /. Decibels AHRI Reference #s Heating apacity High Input/Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Low Input/Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Steady State Efficiency Temperature Rise Range ( F) High/Low - / - - / - - / - No. of Burners Evaporator Motor / oil Motor Type (Belt Drive) -speed Belt Drive -speed Belt Drive -speed Belt Drive Indoor Nominal FM,000,000,000 Indoor Motor FLA (ooling).. Horsepower - RPM.0 -,/8.0 -,/8.0 -,0/8 Metering Device TXV TXV TXV Filter Size (#) 0 x x () 0 x x () 0 x x () Drain Size (NPT) R-0A Refrigerant harge ir #s & & 9 ozs. & 9 ozs. & 9 ozs. Evaporator oil Face Area (ft²) Rows Deep / Fins per Inch / / / Belt Drive Evap Fan Data # of Wheels (D x W) ( x ) ( x ) ( x ) Motor Sheave VP0 x ⅜ VP0 x ⅜ VP0 x ⅜ Blower Sheave 00 x ⁷/₁₆ 00 x ⁷/₁₆ 00 x ⁷/₁₆ Belt BX BX BX ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - RPM ⅓ -,0 ⅓ -,0 ⅓ -,0 Fan Diameter / # Fan Blades / / / Outdoor Nominal FM 9,000 9,000 9,000 Face Area (ft²)... Rows Deep / Fins per Inch / / / ompressor Quantity / Type / Scroll / Scroll / Scroll ompressor RLA / LRA ea..0 / / / 0. Electrical Data Voltage / Phase / Frequency 08/ Standard Max Static... Outdoor Fan FLA / LRA.0 /. 0.8 /. 0. /.8 Total Unit Amps Min. ircuit Ampacity¹ 9. / 9... Max. Overcurrent Protection (amps)² / 0 Entrance Power Supply ⅛ ⅛ ⅛ Entrance ontrol Voltage ⅞ ⅞ ⅞ Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-DG

6 Product Specifications Tons DG00 00V***A* DG00 00V***A* DG00 00V***A* ooling apacity Total, BTU/h 90,000 90,000 90,000 Sensible BTU/h 9,000 9,000 9,000 EER / IEER 9.8 /. 9.8 /. 9.8 /. Decibels AHRI Reference #s Heating apacity High Input/Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Low Input/Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Steady State Efficiency Temperature Rise Range ( F) High/Low - / - - / - - / - No. of Burners Evaporator Motor / oil Motor Type (Belt Drive) -speed Belt Drive -speed Belt Drive -speed Belt Drive Indoor Nominal FM 8,00 8,00 8,00 Indoor Motor FLA (ooling) Horsepower - RPM. - 0/. - 0/. - 0/ Metering Device TXV TXV TXV Filter Size (#) 0 x 0 x (8) 0 x 0 x (8) 0 x 0 x (8) Drain Size (NPT) " " " R-0A Refrigerant harge ir #s & & 98 ozs. & 98 ozs. & 98 ozs. Evaporator oil Face Area (ft²)... Rows Deep / Fins per Inch / / / Belt Drive Evap Fan Data # of Wheels (D x W) (" x ") (" x ") (" x ") Motor Sheave VP8 x ⅜" VP8 x ⅜" VP8 x ⅜" Blower Sheave 0 x ⁷/₁₆" 0 x ⁷/₁₆" 0 x ⁷/₁₆" Belt BX BX BX ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - RPM Fan Diameter / # Fan Blades 0 / 0 / 0 / Outdoor Nominal FM,000,000,000 Face Area (ft²)... Rows Deep / Fins per Inch / / / ompressor Quantity / Type / Scroll / Scroll / Scroll ompressor RLA / LRA IR. # 8. / 8. /. / 00 ompressor RLA / LRA IR. # 8. / 8. /. / 00 Electrical Data Voltage / Phase / Frequency 08/ Outdoor Fan FLA / LRA./../../. Total Unit Amps Min. ircuit Ampacity¹ /.. Max. Overcurrent Protection (amps)² / 0 0 Entrance Power Supply ⅛" ⅛" ⅛" Entrance ontrol Voltage ⅞" ⅞" ⅞" Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-DG

7 Expanded ooling Data Tons (two-speed motor at high speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T 8 0 HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-DG

8 Expanded ooling Data Tons (two-speed motor at high speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T 0 9 HI PR LO PR MBh S/T T 0 HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T 0 HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. 8 SS-DG

9 Expanded ooling Data 0 Tons (two-speed motor at high speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T 0 HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-DG 9

10 Expanded ooling Data 0 Tons (two-speed motor at high speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T 0 HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T 0 HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. 0 SS-DG

11 Expanded ooling Data Tons (Two-Speed Motor at High Speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) Rating onditions. kw = Total system power High and low pressures are measured at the liquid and suction access fittings. Amps: Unit amps (comp.+ evaporator + condenser fan motors) Design Subcooling, - 9 the liquid access fitting connection ARI 9 test conditions. Design Superheat 8 - the compressor suction access fitting connection. SS-DG

12 Expanded ooling Data Tons (Two-Speed Motor at High Speed) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T 9. kw HI PR LO PR MBh S/T T 0.0 kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T 9.9 kw HI PR LO PR MBh S/T T kw HI PR LO PR MBh S/T T kw HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) Rating onditions. kw = Total system power High and low pressures are measured at the liquid and suction access fittings. Amps: Unit amps (comp.+ evaporator + condenser fan motors) Design Subcooling, - 9 the liquid access fitting connection ARI 9 test conditions. Design Superheat 8 - the compressor suction access fitting connection. SS-DG

13 Airflow Data & 0 Tons DG Tons Standard Two-Speed Belt Drive at High Speed ESP In" H₂O Turns Open 0 FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP ,8.,9.9, ,09.09,.,.,0.98, ,90.8,0.80,9.0,.09, ,.9,98.99,8., ,9.989, , DG Tons High-Static Belt Drive Two-Speed at High Speed ESP In" H₂O Turns Open 0 FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP DG 0 Tons Standard Two-Speed Belt Drive at High Speed ESP In" H₂O Turns Open 0 FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP ,9.9 8, ,. 8,88.9, ,08.8 8,.88 8,.89,8.,.88, ,9.98,89.8,8.999, ,9.880,.0, ,9.09, , Notes Airflow table represent dry coil with filters installed; SFM correction factor for wet coil is %. Any adjustment made to the blower should not cause the motor to draw more than the motor rated RLA. Application that exceed the above could require a larger motor. Minimum rated SFM is 0 per ton. Unit factory shipped with the sheave set at. turns open. SS-DG

14 Airflow Data 0 & Tons ESP In" H₂O DG 0 Tons High-Static Belt Drive Two-Speed at High Speed Turns Open 0 FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP DG Tons Standard Two-Speed Belt Drive at High Speed Turns Open 0 RPM ESP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP 0. 9,90. 9,.80 8,99. 8,. 8,8. 8,00.00,. 0. 9,.0 8,8. 8,9.9,90.9,0.90,., ,88.0 8,9.,9.0,8.0,00., ,0.,.80,9.9, ,.98,99., , DG Tons High Static Two-Speed at High Speed Turns Open 0 RPM ESP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP SFM BHP ,8. 9, ,8. 9,9. 8, ,. 9,.0 8,.9, ,0.0 8,0.,88., , ,.8,9.8,8., , ,.88,.,088., ,9.,., ,.8,., ,.9, , Notes Airflow table represent dry coil with filters installed; SFM correction factor for wet coil is %. Any adjustment made to the blower should not cause the motor to draw more than the motor rated RLA. Application that exceed the above could require a larger motor. Minimum rated SFM is 0 per ton. Unit factory shipped with the sheave set at. turns open. Airflow Pressure Drop of Downflow Economizer for - to -Ton Rooftop Units (00% Return Air FM,00,000,00,000,00,000,00 8,000 8,00 9,000 9,00 0,000 (In. WG) SS-DG

15 rankcase Heater, High Efficiency MERV Air Filter Option High Efficiency MERV Air Filter Option 0.0 Flanders Pre Pleat M Air Velocity vs Resistance (Test Size: " x " x " High apacity) " Deep Resistance (in. w.g.) Air Velocity (FPM) Tonnage: Filter Nominal Size: Part Number: Order QTY:, 0 0 x x 00L000 0 X 0 X 00L000 8 rankcase Heater Selection Table ompressor Voltage rankcase ZP/ZPS ompressor Diameter 0V 0V V Heater Watts -." 0R0000S 0R000S 0R000S /." 00L000S 00L0008S 00L0009S L0000S 00L000S 00L000S 90 D* Tonnage ompressor Voltage 0V 0V V rankcase Heater Watts -0 Ton** 00L000S 00L0008S 00L0009S 0 Ton 00L0000S 00L000S 00L000S 90 *Includes,G&H models. **If ompressor Diameter is 9. then use Ton rankcase heaters. SS-DG

16 Electrical Data Tons Model Number 0 Tons Tons Electrical Rating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply RLA LRA RLA LRA QTY HP FLA Type HP FLA FLA MA MOP DG80***W 08/ speed High Static Belt Drive.0 0. DG80***V 08/ speed Belt Drive.00.0 DG80***W speed High Static Belt Drive.0 9. DG80***V speed Belt Drive.00. DG80***W speed High Static Belt Drive.0. DG80***V speed Belt Drive.00. Model Number Electrical Rating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor - 8. / / 00. / / / 0 -. /. 00 / 00. /. 8. / / Optional Powered onvienience Outlet Power Supply RLA LRA RLA LRA QTY HP FLA Type HP FLA FLA MA MOP DG0***W 08/ speed High Static Belt Drive.0 0. DG0***V 08/ speed Belt Drive.00.0 DG0***W speed High Static Belt Drive.0 9. DG0***V speed Belt Drive.00. DG0***W speed High Static Belt Drive.0. DG0***V speed Belt Drive.00. Model Number Electrical Rating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor - 0 / 0 /. /. 0 / 09 / - 9. / 9. /. /. 0 / 0 / Optional Powered onvienience Outlet Power Supply RLA LRA RLA LRA QTY HP FLA Type HP FLA FLA MA MOP DG00***W 08/ speed High Static Belt Drive.0.0 DG00***V 08/ speed Belt Drive.0.0 DG00***W speed High Static Belt Drive.0 0. DG00***V speed Belt Drive.0 0. DG00***W speed High Static Belt Drive.0 8. DG00***V speed Belt Drive / 8 /. /. / / - 8 / 8 /. /. / / SS-DG

17 Dimensions & 0 Tons TOP VIEW FK HOLES BOTH SIDES AND ONDENSER END LIFT SHAKLE HOLES BOTH SIDES AND ENDS ONDENSATE DRAIN OUTLET THIS SIDE ONLY.. BAK VIEW ALL DIMENSIONS ARE GIVEN IN INHES ALL DIMENSIONS AND SPEIFIATIONS ARE SUBJET TO HANGE WITHOUT NOTIFIATION LINE WIRE ENTRANE 88. LEFT END VIEW D*80/0*** AND 0 TON OMERIAL DISONNET SWITH LOATION (if applicable) TSTAT WIRE ENTRANE SS-DG

18 Dimensions, 0, & Tons ONDENSATE DRAIN BOTTOM EXIT X X RETURN AIR DUT SUPPLY AIR DUT.000 BASE PAN VIEW (VIEWED FROM TOP DOWN) 8 SS-DG

19 Dimensions Tons TOP VIEW. FK HOLES BOTH SIDES AND ONDENSER END ONDENSATE DRAN OUTLET THIS SIDE ONLY LEFT SHAKLE HOLES BOTH SIDES AND ENDS. BAK VIEW ALL DIMENSION GIVEN ARE IN INHES ALL DIMENSIONS AND SPEIFIATIONS ARE SUBJET TO HANGE WITHOUT NOTIE LEFT END VIEW LINE WIRE ENTRANE TSTAT WIRE ENTRANE D*00*** -TON OMMERIAL SS-DG 9

20 Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a total clearance of on the main control panel side of the unit for possible removal of fan shaft, coil, electric heat, and gas furnace. Leave a clearance of 8 on all other sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit beneath any obstruction. Install the unit away from all building exhausts to inhibit Ingestion of exhaust air into the unit s fresh-air intake. 8" " " 8" " MINIMUM " MINIMUM ROOF OVERHANG ROOF OVERHANG Electrical Entrance Locations ¹/₈ ³/₅ High-Voltage Entrance ⁴/₅ 0 LowVoltage Entrance SS-DG

21 EVAPAT OILS Roof urb Installation Rigging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 0". Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. Remove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. Refer to rigging label on the unit. Important: If using bottom discharge with roof curb, ductwork should be attached to the curb prior to installing the unit. Duct-work dimensions are shown in Roof urb Installation Instructions Manual. Refer to the Roof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National Roofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. To assist in determining rigging requirements, unit weights are shown below. A Y 0 B OMPRESS ompressor OMPRESS ompressor 0" X G Supply Evaporator oil orner & enter-of-gravity Locations Return D -Ton Units Weights (bls.) 0-Ton Units Weights (lbs.) -Ton Units Weights (lbs.) Weight A 8 Weight A Weight A Weight B Weight B Weight B Weight Weight 89 Weight 0 Weight D Weight D 8 Weight D Shipping Weight 98 Shipping Weight Shipping Weight Operating Weight 08 Operating Weight Operating Weight 8 Note: These weights are calculated without installed accessories. SS-DG

22 Roof urb Installation urb installations must comply with local codes and should follow the established guidelines of the National Roofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Duct-work must be constructed using industry guidelines. The duct-work must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antilevered-type curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. urb Top O.D. 9¾ urb Top O.D. ²/₂₅ ²/₂₅ ²/₂₅ ¾ urb O.D. ⅞ ⅞ ⅞ 8 urb Top O.D. Insulated Panels ¼ ⅝ Typ. ¾ urb Bottom O.D. ⅜ Typ. ¾ ½ urb Bottom O.D. SS-DG

23 9 8 Wiring Diagram DG & 0 Tons (0V Two-Speed Belt Drive) H HR OMP T T T T T T L L L PB HR VM SEE NOTE PLF HPS LPS H HPS LPS T OMP T T HIGH EM LOW VMR R R T T T T T T B HIGH SPEED L L L B LOW SPEED L L L T T T T T T T T T L L L L L B L L L B L TR 08 0 V SEE NOTE NO N NO N ND POWER SUPPLY SEE NOTE 08V / 0V - ph - 0Hz F F F F F F TB M M High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. ALS RS GV S S G R Y Y W W O OOL HEAT L UNUSED L DI PS PLF M FS LS II Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. REPLAE JUMPER WITH SMOKE/FIRE DETET SEE NOTE FS IGN TO THERMOSTAT SEE NOTE 00L00-A SS-DG

24 Wiring Diagram DG & 0 Tons (0V Two-Speed Belt Drive) (cont.) SUPPLY VOLTAGE 08-0//0 L L L OMPONENT LEGEND T T T ALS AUXILLARY LIMIT SWITH T OMP T T B OWER ONTAT OWER RELAY B OMP IRUIT EAKER OMPRESS F F M M H ONDENSER MOT OMPRESS ONTAT RANK ASE HEATER F HR RANK ASE HEATER RELAY F R OMPRESS ONTAT RELAY M EM EVAPAT MOT F F F FUSE M F FAN APAIT L 9 F B B H H NOTE II B B EON H T 8 0 T HIGH SPEED HR HR FS D OMP T T EM LS PS ALS T V TR RS HPS LOW SPEED B B 08-0v B B R R T IGN B VMR FS B B B VMR LPS GV VM HPS LPS B B R L FS FLAME SENS EQUIPMENT OUND GV GAS VALVE HPS HIGH PRESSURE SWITH I INDO OWER RELAY II INTEATED IGNITION ONTROL IGN IGNIT LPS LOW PRESSURE SWITH LS LIMIT SWITH PB POWER DISTRUBTION OK PLF FEMALE PLUG/ONNET PS PRESSURE SWITH RS ROLLOUT SWITH TB TERMINAL OK (V SIGNAL) TB TERMINAL OK (L) TR TRANSFMER VM VENT MOT VMR VENT MOT RELAY NOTES. REPLAEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS IGINAL. (USE OPPER ONDUT ONLY).. AESSY EONOMIZER PLUG ADJAENT TO OWER HOUSING IN RETURN AIR OMPARTMENT. REMOVE MALE PLUG AND ATTAH FEMALE PLUG TO THE EONOMIZER AESSY.. L AND L ON II ONTROL IS V INT.. USE OPPER ONDUTS ONLY. USE NE LASS WIRE.. F TWO STAGE OPERATION REMOVE. F TWO STAGE OPERATION REMOVE W TO W WIRE JUMPER. W TO W WIRE JUMPER.. F 08V OPERATION MOVE AK WIRE FROM TERMINAL TO TERMINAL ON THE TRANSFMER. High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. R THERMOSTAT S R S W Y W Y G O TO THERMOSTAT SEE NOTE TB STATUS LIGHT ON OFF INK INKS NOTE EQUIPMENT STATUS NMAL OPERATION NO POWER INTERNAL ONTROL IGNITION FAILURE OPEN ROLLOUT SWITH OPEN AUX. LIMIT SWITH HR INSTALLER/SERVIEMAN THE STATUS LIGHT ON THE FURNAE ONTROL MAY BE USED AS A GUIDE TO TROUESHOOTING THIS APPLIANE. STATUS LIGHT ODES ARE AS FOLLOWS: PRESSURE SWITH OPEN HR SEE NOTE 9 8 HEK HEK INT POWER HEK FUSE ON ONTROL REPLAE ONTROL GAS FLOW GAS PRESSURE GAS VALVE FLAME SENS FLAME ROLLOUT BAD SWITH AUX. LIMIT OPEN HEK PRESSURE SWITH FATY WIRING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE WIRE ODE AK UE OWN EEN ANGE PINK RPLE RED ITE YELLOW / YELLOW WITH FIELD WIRING STAGE OOLING W G R Y Y O TB W G R Y Y O STAT Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. INKS PRESSURE SWITH LOSED WITHOUT INDUER ON HEK PRESSURE SWITH PINK STRIP / UE WITH INKS OPEN LIMIT SWITH MAIN LIMIT OPEN BAD SWITH PINK STRIP INKS FALSE FLAME SENSED STIKING GAS VALVE INKS OMPRESS OUTT DELAY MIN. OMP. ANTI-YLE TIMER SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION 00L09-A SS-DG

25 9 8 Wiring Diagram DG & 0 Tons (0V/ V Two-Speed Belt Drive) H HR OMP T T T T T T L L L PB HR VM SEE NOTE PLF HPS LPS H HPS LPS T OMP T T HIGH EM LOW VMR R R T T T T T T B HIGH SPEED L L L B LOW SPEED 0 APPROPRIATE INT VOLTAGE 0 L L L T T T T T T T T T L L L L L B L L L B L TR 0 V SEE NOTE NO N NO N ND POWER SUPPLY SEE NOTE 0V / V - ph - 0Hz F F F F F F TB M M High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. 00L00-B ALS RS GV S S REPLAE JUMPER WITH SMOKE/FIRE DETET G R Y Y W W O TO THERMOSTAT ++ SEE NOTE SEE NOTE OOL HEAT L UNUSED L DI FS IGN PS 9 8 PLF 0 WIRING ODE FATY WIRING HIGH VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE OPTIONAL LOW VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE ++ USE N.E.. LASS WIRE M FS LS II OL ODE AK UE OWN ANGE RPLE RED ITE YELLOW PINK EEN Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. SS-DG

26 Wiring Diagram DG & 0 Tons (0V/ V Two-Speed Belt Drive) (cont.) L SUPPLY VOLTAGE 0///0 L L OMPONENT LEGEND T T OMP T T T T ALS B OMP AUXILLARY LIMIT SWITH OWER ONTAT OWER RELAY OMPRESS M ONDENSER MOT F F M H HR R OMPRESS ONTAT RANK ASE HEATER RANK ASE HEATER RELAY OMPRESS ONTAT RELAY F F EM F EVAPAT MOT FUSE M F F FAN APAIT F FS FLAME SENS NOTE L 9 F B B H H NOTE II II B B EON H T 8 0 T HIGH SPEED HR HR FS D OMP T T EM LS PS T 0V V ALS IGN FS TR T LOW SPEED B B B B R R RS B HPS VMR TR 0V V B B B VMR LPS GV M HPS LPS VM B B R L EQUIPMENT OUND GV GAS VALVE HPS HIGH PRESSURE SWITH I INDO OWER RELAY II INTEATED IGNITION ONTROL IGN IGNIT LPS LOW PRESSURE SWITH LS LIMIT SWITH PLF FEMALE PLUG/ONNET PS PRESSURE SWITH RS ROLLOUT SWITH TB TERMINAL OK (V SIGNAL) TB TERMINAL OK (L) TR TRANSFMER VM VENT MOT VMR VENT MOT RELAY NOTES. REPLAEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS IGINAL. (USE OPPER ONDUT ONLY).. AESSY EONOMIZER PLUG ADJAENT TO OWER HOUSING IN RETURN AIR OMPARTMENT. REMOVE MALE PLUG AND ATTAH FEMALE PLUG TO THE EONOMIZER AESSY.. L AND L ON II ONTROL IS V INT.. USE OPPER ONDUTS ONLY. USE NE LASS WIRE.. F TWO STAGE OPERATION REMOVE W TO W WIRE JUMPER. W TO W WIRE JUMPER. High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. TB REPLAE JUMPER WITH SMOKE/FIRE DETET S S R G W W Y Y O STATUS LIGHT ON OFF INK INKS INKS INSTALLER/SERVIEMAN THE STATUS LIGHT ON THE FURNAE ONTROL MAY BE USED AS A GUIDE TO TROUESHOOTING THIS APPLIANE. STATUS LIGHT ODES ARE AS FOLLOWS: STATUS LIGHT ON OFF INK INKS INKS TO THERMOSTAT ++ SEE NOTE EQUIPMENT STATUS EQUIPMENT STATUS NMAL OPERATION NMAL OPERATION NO POWER INTERNAL ONTROL NO POWER INTERNAL ONTROL IGNITION FAILURE IGNITION FAILURE OPEN ROLLOUT SWITH OPEN ROLLOUT SWITH OPEN AUX. LIMIT SWITH OPEN AUX. LIMIT SWITH PRESSURE SWITH OPEN PRESSURE SWITH OPEN PRESSURE SWITH LOSED WITHOUT INDUER ON PRESSURE SWITH LOSED WITHOUT INDUER ON HR R HR 9 8 PLF NOTE HEK HEK HEK INT POWER HEK INT POWER HEK FUSE ON ONTROL HEK FUSE ON ONTROL REPLAE ONTROL REPLAE ONTROL GAS FLOW GAS FLOW GAS PRESSURE GAS PRESSURE GAS VALVE GAS VALVE FLAME SENS FLAME SENS FLAME ROLLOUT FLAME ROLLOUT BAD SWITH BAD SWITH AUX. LIMIT OPEN AUX. LIMIT OPEN HEK HEK PRESSURE SWITH PRESSURE SWITH HEK HEK PRESSURE SWITH PRESSURE SWITH FATY WIRING LINE VOLTAGE LOW VOLTAGE FIELD WIRING HIGH VOLTAGE WIRE ODE AK UE OWN EEN ANGE PINK RPLE RED ITE YELLOW / YELLOW WITH PINK STRIP / UE WITH PINK STRIP THERMOSTAT FIELD WIRING STAGE OOLING W G R Y Y O TB NO EONOMIZER W G R Y Y O TB WITH EONOMIZER OPTION W G R Y Y O TB W G R Y Y O STAT W G R Y O STAT W G R Y O STAT Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. INKS INKS INKS INKS OPEN LIMIT SWITH OPEN LIMIT SWITH FALSE FLAME SENSED FALSE FLAME SENSED MAIN LIMIT OPEN BAD SWITH BAD SWITH STIKING GAS VALVE STIKING GAS VALVE INKS INKS OMPRESS OMPRESS OUTT DELAY OUTT DELAY MIN. OMP. MIN. OMP. ANTI-YLE TIMER ANTI-YLE TIMER SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION 00L09-A SS-DG

27 Wiring Diagram DG Tons (0V/0V/V, Speed Belt Drive - ontrols Diagram) FIELD ONTROL WIRING LASS TB W W G R Y YI S S THERMOSTAT WIRING STAGE OOLING W W G G R R Y Y Y Y O O STAT TB SMOKE DETET 0 9 V A/D Y Y SENS R B AUX A Y Y SENS R 8 AUX B B 8 Y Y R B Y Y R B SEN SEN SMK DET OPTION SUPPLY (LINE) VOLTAGE TR VA TB R HPS LPS TB PLM PLF R MR EON EON SHRT PLF PLM FM FM EON PLM HPS LAM PLF PLM 8 9 PLF PLM PLF G LUG PLM LPS -t -t -t EON MODULE MAT AUX-I MAT O E- OAT OAT EXH AUX-O S-BUS S-BUS Y-I Y-O IAQ -0 Y-I IAQ OM Y-O IAQ V AT OM R AT V M M B LOW SPEED MAS OD ENTH EON AT B HIGH SPEED EON OPTION High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. A II V V OM GV LIMIT SW PRESSURE SW G IN PRESSURE SW R W IN Y IN OMP OUT OOL HEAT L L FS D L NOTES:. REPLAEMENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (USE OPPER ONDUTS ONLY).. IF OPTIONAL EONOMIZER IS INSTALLED, REMOVE EON SHRT PLM AND ONNET EON PLM TO EON PLF.. TB LOW VOLTAGE TERMINAL OK. TERMINALS F VA PWR (,, WIRE) AND TERMINALS F VA OM ( WIRE).. ONNETIONS SHOWN ARE F -STAGE HEAT OPERATION. EN -STAGE OPERATION IS REQUIRED REMOVE JUMPER WIRE ONNETING W TO W ON TB.. IF OPTIONAL SMOKE DETET IS INSTALLED, REMOVE JUMPER WIRE ONNETING S TO S ON TB AND MAKE THE FOLLOWING WIRE ONNETIONS: WIRE TO S, WIRE TO TB (V/PWR), WIRE TO TB (V/OM). FS LAR VMR LS LAM LAT T T T. IF LOW AMBIENT KIT IS INSTALLED, ONNET WIRE FROM LAM- TO MR-. ALSO ONNET OM WIRES FROM LAT-T AND LAM - TO TB (V OM).. LAT ON/OFF TIME SETTINGS : ON - TIME (LEFT OLUMN) :,8 = ON OFF - TIME (RIGHT OLUMN) : 8 = ON ALL - OTHER DIP SWITHES = OFF PS ALS ONTROLS DIAAM DG00***(,,) V SPD EM PLF PLM RS -t LA M GV ND STG ST STG LOW AMB OPTION OM 00L0-A Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. SS-DG

28 WIRING DIAAMS F MODELS WITH DD ONTROLS For complete information and installation instructions for models with DD controls, see manual DK-DD-TGD-XXX 8 SS-DG

29 Wiring Diagram with DD DG080*/ DG0* 08-0, 0, / / 0 SP ontrol ONTROL WIRING DIAAM DG(80-0) ****V DD TB (LASS) AG (OMP IN) (OMP OUT) (OMP OUT) (OMP IN) SMK/EMG LINE VOLTAGE TR DAT TB T T T T (LASS) VA T PS ES XS DA S -t V BS DD (LASS) OM RLY HPS LPS RLY / / / / OM (OWER STAGE ) RLY RLY (HEAT ) RLY HPS LPS (HEAT ) RLY 8 / / / RLY 9 / RLY8 0 (V IN) OM-8 (EON PWR) OM-8 RSS 8 BI (EMER) BI (FAN PROV) LDS BI (OMP PRESS ) BI (OMP PRESS ) BI (RMT STRT/STP) FS BI (SHED) (BA R+ BI (FS) NET) SH BA NET BI8 T- EON PLF OAT -t (EON DMPR) AO OAH AO VA VOUT (D) (PWR) (EXF) AO (ALRM) AO O VA VOUT (D) (PWR) 0 AI (SUPPLY AIR TMP) TWISTED VA 9 AI SPTEMP (OAT) EXF NTL RLY PAIR (OM) (EON FB) TEMP 8 AI 0VD STPT OFFSET AI (OAH) G AI (O) AI (SP TMP) IAH AI (SP SLIDE ADJ) VA VOUT (D) AI8 (SP HUM) (PWR) A (ISOL ) A ALRM NTL RLY 0VD G VA (OWER STAGE ) B (LO SPD) HTR PLF HTR PLM B (HI SPD) High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. NOTES: II VA PWR F VA OM A GV OUT F TMP LMT OUT TMP LMT IN PRESS SW IN PRESS SW OUT 8 HEAT IN FLAME SENSE VA L PWR L L VA L OM L L VENT MTR D IGNIT HEAT 0 GV RS ST STG OM ND STG ALS LS PS FS VMR Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring.. REPLAEMENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (AT LEAST 0 ). USE OPPER ONDUTS ONLY. USE N.E.. LASS WIRE F ALL LOW VOLTAGE FIELD ONNETIONS. IF OPTIONAL SMOKE DETET IS INSTALLED, REMOVE RED JUMPER WIRE ONNETIONS TB-XS TO TB-ES. DISHARGE AIR TEMPERATURE SENS SHIPPED WITH UNIT IN ONTROL BOX. INSTALL AND ONNET PER THE ATTAHED INSTRUTIONS/WIRING DIAAM. IF OPTIONAL EONOMIZER IS INSTALLED, ONNET EON PLF TO EONOMIZER. EONOMIZER PLUG LOATED IN THE RETURN AIR OMPARTMENT. SEE POWER DIAAM F ONTROL TRANSFMER (TR) HIGH VOLTAGE ONNETIONS. 00L08-A SS-DG 9

30 Wiring Diagram with DD DG080*/ DG0* 08-0 / / 0 SP Power LINE VOLTAGE L L L POWER WIRING DIAAM DG(80-0) **** DD II DIAGNOSTI INK ODES EQUIPMENT STATUS HEK STATUS LIGHT ON NMAL OPERATION HEK INT POWER NO POWER OFF HEK FUSE ON ONTROL INTERNAL ONTROL REPLAE ONTROL INK IGNITION FAILURE OPEN ROLLOUT SWITH OPEN AUX LIMIT SWITH GAS FLOW GAS PRESSURE GAS VALVE FLAME SENSER FLAME ROLLOUT BAD SWITH AUX.LIMIT OPEN INKS PRESSURE SWITH OPEN HEK PRESSURE SWITH INKS PRESSURE SWITH LOSED WITHOUT INDUER ON HEK PRESSURE SWITH L L L PB AS INKS OPEN LIMIT SWITH MAIN LIMIT OPEN BAD SWITH H INKS INKS FALSE FLAME SENSED OMPRESS OUTT DELAY STIKING GAS VALVE MIN. OMP. ANTI-YLE TIMER, TR VMR LINE VOLTAGE NOTES:. REPLAEMENT WIRE MUST BE SAME SIZE AND TYPE OF INSULATION AS IGINAL (USE OPPER ONDUTS ONLY).. THE ONTROL TRANSFMER HAS MULTIPLE HIGH VOLTAGE TAPS. ENSURE WIRE ONNETIONS ARE RET F UNIT SUPPLY VOLTAGE RATING. 08/0V SUPPLY POWER UNITS ARE FATY ONNETED TO THE ONTROL TRANSFMER 0V TAP. MOVE WIRE ONNETION FROM 0V TAP TO 08V TAP EN 08V POWER SUPPLY IS USED.. SEE ONTROL DIAAM F ONTROL TRANSFMER LOW VOLTAGE ONNETIONS. OPTIONAL; B,B,B AND ASSOIATED WIRING IS PRESENT ONLY WITH -SPEED EVAPAT MOT.. USE OPPER ONDUTS ONLY. UNIT TERMINALS ARE NOT DESIGNED F OTHER ONDUTS. THE USE OF OTHER TYPE ONDUTS MAY AUSE DAMAGE TO THE UNIT.. SEE AESSY KIT LITERATURE F OPTIONAL ONVENIENE OUTLET WIRING DIAAM. AS II IGN VM IGN L L L L L L B B H T T T T T T L L L F F F B HIGH SPEED T T T B LOW SPEED L T L T L T ALS ALRM B BS BM B AS H F FS OMP O DAT DD EON EXF F FS GV HH HPS HVTB IAH II LS LDS LPS OAT OAH PB PLF PLM PS RS RSS SMK SP TEMP TB TR VM VMR L L L L L L T T T T T T F HVTB OMPONENT LEGEND AUXILIARY LIMIT SWITH ALARM OWER ONTAT OWER URRENT SWITH OWER MOT IRUIT EAKER OMPRESS ONTAT OMPRESS ONTAT AUXILIARY SWITH RANK ASE HEATER ONDENSER FAN LOGGED FILTER SWITH OMPRESS ARBON DIOXIDE SENS DISHARGE AIR TEMPERATURE SENS DIRET DIGITAL ONTROL EONOMIZER EXHAUST FAN FAN APAIT FLAME SENSE EQUIPMENT OUND GAS VALVE HOT GAS REHEAT HIGH PRESSURE SWITH HIGH VOLTAGE TERMINAL BOA INDO AIR HUMIDITY SENS INTEATED IGNITION ONTROL LIMIT SWITH LOAD SHEDDING LOW PRESSURE SWITH OUTDO AIR TEMPERATURE SENS OUTDO AIR HUMIDITY SENS POWER DISTRIBUTION OK FEMALE PLUG/ONNET MALE PLUG/ONNET PRESSURE SWITH ROLL-OUT SWITH REMOTE START/STOP SMOKE DETET SPAE TEMPERATURE SENS TERMINAL OK (V SIGNAL) TRANSFMER VENT MOT VENT MOT RELAY L L OMP L L L OMP L BM F F F FATY WIRING HIGH VOLTAGE LOW VOLTAGE OPTIONAL LOW VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE OPTIONAL AESSIES FIELD SUPPLIED WIRE ODE AK UE OWN EEN AY ANGE PINK RPLE RED ITE YELLOW / YELLOW WITH PINK STRIPE / UE WITH PINK STRIPE High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. Wiring is subject to change. Always refer to the wiring diagram on the Warning unit for the most up-to-date wiring. 00L08-A 0 SS-DG