DSG Commercial. 3-5 Ton Packaged Gas/ Electric Units 14 SEER / up to 12.0 EER Up to 81% Efficient

Transcription

1 DS ommercial - 5 Ton Packaged as/ Electric Units 4 SEE / up to 2.0 EE Up to 8% Efficient ooling apacity: 5,000 58,000 BTU/h Heating apacity: 46,000 8,000 BTU/H ontents Nomenclature... 2 Product Specifications... 4 Expanded ooling Data... Airflow Data... 9 rankercase Heater Electrical Data Dimensions iring Diagrams... for Models with DD ontrols... 5 Accessories Standard Features Patented tubular heat exchanger High-efficiency scroll compressor High and low-pressure switches opper tube / aluminum fin coils ontactor with lugs High-capacity, steel-cased filter drier 24-volt terminal strip onvertible airflow orientation Easy to service Built-in filter rack with standard 2" filters Bottom utility entry omplies with alifornia Low NOx emissions standards -5 Tons with single speed blower motor units meet the performance specified in Table of ASHAE Standard AHI ertified; ETL Listed abinet Features Heavy-gauge, galvanized-steel cabinet with UV-resistant powder-paint finish Full Perimeter ail Sloped drain pan * omplete warranty details available from your local distributor or manufacturer s representative or at SS-DS 2/7 Supersedes 8/7

2 Nomenclature D S B * * * A * 2 4,5,6 7,8, evision Levels Major & Minor Brand Factory-Installed Options D Daikin X No Options A Non-powered convenience outlet onfiguration B Powered convenience outlet Standard Efficiency (6-25 Tons) Low-ambient kit S Standard Efficiency ( - 5 Tons) D eturn air smoke detector T High Efficiency ( - 5 Tons) E Supply air smoke detector F Non-powered convenience outlet; Application Low-ambient kit ooling Non-powered convenience outlet; as Heat eturn air smoke detector H Heat Pump H Non-powered convenience outlet; Supply air smoke detector Nominal ooling apacity J Non-powered convenience outlet; 06 Tons 02 8½ Tons Tons eturn & Supply air smoke detectors Tons 20 0 Tons K Non-powered convenience outlet; Tons 50 2½ tons Low-ambient kit; Supply air smoke detector Tons 80 5 Tons L Non-powered convenience outlet; 090 7½ Tons Tons Low-ambient kit eturn & Supply air smoke detectors Nominal Heating apacity M Powered convenience outlet; as/electric A/ H/P Factory-Installed Electric Heat Low-ambient kit ,000 BTU/h XXX No Heat N Powered convenience outlet; ,000 BTU/h 00 0 k 00 0 k eturn air smoke detector ,000 BTU/h 05 5 k 0 0 k O Powered convenience outlet; 5 5,000 BTU/h 06 5 k k eturn & Supply air smoke detectors 40 40,000 BTU/h 08 8 k k P Powered convenience outlet; 20 20,000 BTU/h k k Supply air smoke detector 50 50,000 BTU/h k Q Powered convenience outlet; Low-ambient ,000 BTU/h kit; eturn air smoke detector See product specifications for heat size(s) available for each capacity. Powered convenience outlet; Low-ambient Voltage kit; Supply air smoke detector // //60 T Powered convenience outlet; Low-ambient // //60 kit; eturn & Supply air smoke detectors U Non-powered convenience outlet; Supply Fan/Drive Type/Motor Low-ambient kit; eturn air smoke detector B Belt Drive (single speed) V Two-Speed Belt Drive (also designates 6-Ton V Low-ambient kit; eturn air smoke detector D Direct Drive (-5 Tons) with two-stage compressor) Low-ambient kit; Supply air smoke detector H High Static (single-speed Belt Drive models only) Y Low-ambient kit; eturn & Supply Factory-Installed Options air smoke detectors A Ultra Low-Leak Downflow Economizer Ultra Low-Leak Downflow Economizer; Z eturn & Supply air smoke detectors B DD-BAnet protocol DD-BAnet protocol; F Ultra Low-Leak Downflow Economizer; Disconnect Switch (non-fused) DD-BAnet protocol V Low-Leak Downflow Economizer Factory-Installed Options H Disconnect Switch (non-fused) Low-Leak Downflow Economizer X Standard Aluminized Heat Exchanger J Ultra Low-Leak Downflow Economizer; Disconnect Switch (non-fused) S Stainless-Steel Heat Exchanger Disconnect Switch (non-fused) X No Options D Hinged Panels M Disconnect Switch (non-fused); DD-BAnet protocol K Stainless-Steel Heat Exchanger; Hinged Panels Note: Not all options available for all products. B Phase Monitor X= No Options in character th J Stainless Steel Heat Exchanger; Phase Monitor M Hinged Panel; Phase Monitor L Stainless-Steel Heat Exchanger; Hinged Panels; Phase Monitor 2 SS-DS

3 Factory-Installed Options Stainless-Steel Heat Exchanger (as only units): A tubular heat exchanger made of 409-type stainless steel is installed in the unit. Low-Ambient Kit: Allows for cooling operation at lower outdoor temperatures. On the - to 6-ton units, cooling operation is extended from 60 F ambient temperature to 5 F outside air temperature. On 7½ -20 ton units, cooling operation is extended from 5 F ambient temperature to 0 F outside air temperature. For 25 ton units, cooling operation is extended from 24 F ambient temperature to 0 F outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (heat pump and cooling units only): Available in all voltage options. Non-powered onvenience Outlet: A 20V, 5A, FI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 20V, 5A, FI outlet powered with a transformer built into the unit. hen a factory-installed powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.2A/6.5A for 208/20V units, increase by.a for 460V units, and by 2.6A for 575V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (non-fused; -phase units only): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning and heat pump models, the appropriate electric heat kit must be ordered to be factory-installed along with the disconnect switch (non-fused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (non-fused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (non-fused) is in the off position. eturn Air and/or Supply Air Smoke Detectors: eturn air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all units. Two-speed indoor fan blower models are available on 6, 7½, 8½, 0, 2½, 5, 20 & 25 ton units. Section b of ASHAE Standard and Section a of ASHAE Standard require a minimum of two fan speeds. Section 40.4(m) of alifornia Energy ommission Title contains a similar provision. hen the units with the two-speed indoor fan blowers operate on a call for the first stage of cooling, the fan operates at low speed, which is 66% of full speed. hen the units operate on a call for the second stage of cooling, the fan operates at full speed. In heating operation, the fan operates at full speed. During ventilation operation, the fan operates at low speed. eturn Air and/or Supply Air Smoke Detectors: eturn air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all models. Phase Monitor: Phase monitor ( phase only), available for - 25 ton DS, D and DT series models. Phase monitor shall provide protection for motors and compressors against problems caused by phase loss, phase reversal and phase unbalance. Phase monitor is equipped with an LED that provides an ON or FAULT indicator. DD ontroller: DD communicating controller, available for - 25 ton DS, D and DT series models with on-board BAnet communication interface. SS-DS

4 Product Specifications Tons DS06 045D***A* DS06 045D***A* DS06 045B***A* DS B***A* ooling apacity Total BTU/h 6,000 6,000 5,000 5,000 Sensible BTU/h 26,640 26,640 25,600 25,600 SEE / EE 4 / 2 4 / 2 4 / 2 4 / 2 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 46 / / / / 6.8 Low Input / Output BTU/h Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Indoor Nominal FM,250,250,200,200 Motor Speed Tap (ooling) Low Speed Low Speed Indoor Motor FLA (ooling) Horsepower - PM / - 90 / Piston Size (ooling) Filter Size (") (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") Motor Sheave VL4 X ⅝ VL4 X ⅝ Blower Sheave / Belt AK6 x / AX5 AK6 x / AX5 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ -,050 Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22/4 22/4 Outdoor Nominal FM,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch / 24 / 24 / 24 / 24 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 6.7 / / / / 8.0 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA / / 2.46 / / 2.46 /.4 /.7 Max. External Static 0.5" 0.5".0".0" Outdoor Fan HP / FLA ¼ /.4 ¼ /.4 ¼ /.4 ¼ / 0.7 Min. ircuit Ampacity¹ 24.7 / / / Max. Overcurrent Protection (amps)² 40 / / / 25 5 Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. 4 SS-DS

5 Product Specifications Tons (cont.) DS06 070B***A* DS B***A* ooling apacity Total BTU/h 5,000 5,000 Sensible BTU/h 25,600 25,600 SEE / EE 4 / 2 4 / 2 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 69 / / 55 Low Input / Output BTU/h 5 / 4 5 / 4 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low / / 5-45 No. of Burners Evaporator Motor / oil Motor Type Belt Drive Belt Drive Indoor Nominal FM,200,200 Motor Speed Tap (ooling) Indoor Motor FLA (ooling).4.7 Horsepower - PM ,725 Piston Size (ooling) Filter Size (") (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") Motor Sheave VL4 x ⅝ VL4 x ⅝ Blower Sheave / Belt AK6 x / AX5 AK6 x / AX5 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,050 Fan Diameter/ # Fan Blades 22/4 22 / 4 Outdoor Nominal FM,800,800 Face Area (ft²) ows Deep/ Fins per Inch / 24 / 24 ompressor Quantity / Type/ Stage / Scroll/Single / Scroll/Single ompressor LA / LA 0.4 / / 8.0 Electrical Data Voltage-Phase-Frequency 208/ Indoor Blower HP / FLA /.4 /.7 Max. External Static.0".0" Outdoor Fan HP / FLA ¼ /.4 ¼ / 0.7 Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² 25 5 Power Supply onduit Hole Low-Voltage onduit Hole ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. SS-DS 5

6 Product Specifications Tons (cont.) DS06 090D***A* DS06 090D***A* DS06 090B***A* DS B***A* DS B***A* ooling apacity Total BTU/h 6,000 6,000 5,000 5,000 5,000 Sensible BTU/h 26,640 26,640 25,600 25,600 25,600 SEE / EE 4 / 2 4 / 2 4 / 2 4 / 2 4 / 2 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 92 / / / / / 74 Low Input / Output BTU/h 69 / / / / / 55 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low 0-60 / / / No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Belt Drive Indoor Nominal FM,250,250,200,200,200 Motor Speed Tap (ooling) LO LO Indoor Motor FLA (ooling) Horsepower - PM ⅓ - 90 ⅓ , ,725 Piston Size (ooling) Filter Size (") (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") (" x 0") Motor Sheave VL4 x ⅝ VL4 x ⅝ VL4 x ⅝ Blower Sheave / Belt AK6 x / AX5 AK6 x / AX5 AK6 x / AX5 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ -,050 ¼ -,050 Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22/4 22 / 4 22 / 4 Outdoor Nominal FM,800,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch / 24 / 24 / 24 / 24 / 24 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 6.7 / / / / / 6.5 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA / / 2.46 / / 2.46 /.4 /.7.5 / 2. Max. External Static 0.5" 0.5".0".0".0" Outdoor Fan HP / FLA ¼ /.4 ¼ /.4 ¼ /.4 ¼ / 0.7 ¼ / 0.55 Min. ircuit Ampacity¹ 24.7 / / / Max. Overcurrent Protection (amps)² 40 / / / Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. 6 SS-DS

7 Product Specifications 4 Tons DS B***A* DS B***A* ooling apacity Total BTU/h 47,000 47,000 Sensible BTU/h 5,000 5,000 SEE / EE 4 /.8 4 /.8 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 69 / / 55 Low Input / Output BTU/h 5 / 4 5 / 4 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low / / 0-40 No. of Burners Evaporator Motor / oil Motor Type Belt Drive Belt Drive Indoor Nominal FM,600,600 Motor Speed Tap (ooling) Indoor Motor FLA (ooling).4.7 Horsepower - PM.0 /,725.0 /,725 Piston Size (ooling) Filter Size (") (4)4 x 20 x 2 (4)4" x 20" x 2" Drain Size (NPT) ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) () x 0 () x 0 Motor Sheave VL40 X ⅝ VL40 X ⅝ Blower Sheave / Belt AK66 X / AX52 AK66 X / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ Fan Diameter/ # Fan Blades 22 / 4 22 / 4 Outdoor Nominal FM,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll/Single / Scroll/Single ompressor LA / LA. / / 4 Electrical Data Voltage-Phase-Frequency 208/ Indoor Blower HP / FLA.0 /.4.0 /.7 Max. External Static.0".0" Outdoor Fan HP / FLA ¼ /.4 ¼ / 0.7 Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² 0 5 Power Supply onduit Hole Low-Voltage onduit Hole ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. SS-DS 7

8 Product Specifications 4 Tons (cont.) DS D***A* DS D***A* DS B***A* DS B***A* ooling apacity Total BTU/h 48,000 48,000 47,000 47,000 Sensible BTU/h 5,520 5,520 5,000 5,000 SEE / EE 4 / 2 4 / 2 4 /.8 4 /.8 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 92 / / / / 74 Low Input / Output BTU/h 69 / / / / 55 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low 25-50/ / / / 5-45 No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Indoor Nominal FM,600,600,600,600 Motor Speed Tap (ooling) LO LO Indoor Motor FLA (ooling) Horsepower - PM ¾ -,025 ¾ -,025.0 /,725.0 /,725 Piston Size (ooling) Filter Size (Qty) (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4)4 x 20 x 2 (4)4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) 0 0 Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) () x 0 () x 0 Motor Sheave VL40 X ⅝ VL40 X ⅝ Blower Sheave / Belt AK66 X / AX52 AK66 X / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22 / 4 22 / 4 Outdoor Nominal FM,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 9.9 / 09./ 8.. / / 4 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA ¾ / 2.8 ¾ / /.4.0 /.7 Max. External Static 0.5" 0.5".0".0" Outdoor Fan HP / FLA Min. ircuit Ampacity¹ 29 / / / Max. Overcurrent Protection (amps)² 45 / 45 0 / 0 0 / 0 5 Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. 8 SS-DS

9 Product Specifications 4 Tons (cont.) DS048 5D***A* DS048 5D***A* DS048 5B***A* DS048 54B***A* DS048 57B***A* ooling apacity Total BTU/h 48,000 48,000 47,000 47,000 47,000 Sensible BTU/h 5,520 5,520 5,000 5,000 5,000 SEE / EE 4 / 2 4 / 2 4 /.8 4 /.8 4 /.8 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 5 / 9 5 / 92 5 / 92 5 / 92 5 / 92 Low Input / Output BTU/h 86 / / / / / 69 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low / / / / / No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Belt Drive Indoor Nominal FM,600,600,600,600,600 Motor Speed Tap (ooling) LO LO Indoor Motor FLA (ooling) Horsepower - PM ¾ -,025 ¾ -,025.0 /,725.0 /,725.5 /,725 Piston Size (ooling) Filter Size (Qty) (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4)4" x 20" x 2" (4)4" x 20" x 2" (4)4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) 0 0 Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) () x 0 () x 0 () x 0 Motor Sheave VL40 X ⅝ VL40 X ⅝ VL40 X ⅝ Blower Sheave / Belt AK66 X / AX52 AK66 X / AX52 AK66 X / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ ¼ Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22 / 4 22 / 4 22 / 4 Outdoor Nominal FM,800,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 9.9 / 09./ 8.. / / /.0 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA ¾ / 2.8 ¾ / /.4.0 /.7.5 / 2. Max. External Static 0.5" 0.5".0".0".0" Outdoor Fan HP / FLA Min. ircuit Ampacity¹ 29 / / / Max. Overcurrent Protection (amps)² 45 / 45 0 / 0 0 / Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. SS-DS 9

10 Product Specifications 5 Tons DS D***A* DS D***A* DS B***A* DS B***A* ooling apacity Total BTU/h 58,000 58,000 58,000 58,000 Sensible BTU/h 42,40 42,40 42,800 42,800 SEE / EE 4 /.6 4 /.6 4 /.6 4 /.6 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 92 / / / / 74 Low Input / Output BTU/h 69 / / / / 55 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low 25-55/ / / / 5-45 No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Indoor Nominal FM,800,800,800,800 Motor Speed Tap (ooling) T T Indoor Motor FLA (ooling) Horsepower - PM -,050 -, Piston Size (ooling) Filter Size (Qty) (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") Motor Sheave VL40 x ⅞ VL40 x ⅞ Blower Sheave / Belt AK6 x / AX52 AK6 x / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ -,075 Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22 / 4 22 / 4 Outdoor Nominal FM,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 26.4 / / / / 52 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA.0 / / /.2.0 /.5 Max. External Static 0.9" 0.9".0".0" Outdoor Fan HP / FLA ¼ /.40 ¼ /.40 ¼ /.40 ¼ / 0.7 Min. ircuit Ampacity¹ 4. / / / Max. Overcurrent Protection (amps)² 60 / / / 40 5 Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. 0 SS-DS

11 Product Specifications 5 Tons (cont.) DS060 5B***A* DS060 54B***A* ooling apacity Total BTU/h 58,000 58,000 Sensible BTU/h 4,200 4,200 SEE / EE 4 /.6 4 /.6 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 5 / 92 5 / 92 Low Input / Output BTU/h 86 / / 69 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low 5-65 / / No. of Burners 5 5 Evaporator Motor / oil Motor Type Belt Drive Belt Drive Indoor Nominal FM,800,800 Motor Speed Tap (ooling) Indoor Motor FLA (ooling) Horsepower - PM Piston Size (ooling) Filter Size (") (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") Motor Sheave VL40 x ⅞ VL40 x ⅞ Blower Sheave / Belt AK6 X / AX52 AK6 X / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 Fan Diameter/ # Fan Blades 22 / 4 22 / 4 Outdoor Nominal FM,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll/Single / Scroll/Single ompressor LA / LA 6.0/ / 52.0 Electrical Data Voltage-Phase-Frequency 208/ Indoor Blower HP / FLA.0 /.2.0 /.5 Max. External Static.0".0" Outdoor Fan HP / FLA ¼ /.40 ¼ / 0.7 Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² 40 5 Power Supply onduit Hole.25".25" Low-Voltage onduit Hole ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. SS-DS

12 Product Specifications 5 Tons (cont.) DS060 40D***A* DS060 40D***A* DS060 40B***A* DS B***A* DS B***A* ooling apacity Total BTU/h 58,000 58,000 58,000 58,000 58,000 Sensible BTU/h 42,40 42,40 4,200 4,200 42,500 SEE / EE 4 /.6 4 /.6 4 /.6 4 /.6 4 /.6 Decibels AHI eference #s Heating apacity High Input / Output BTU/h 8 / 2 8 /0 8 /0 8 /0 8 /0 Low Input / Output BTU/h 04 / 84 0 / 8 0 / 8 0 / 8 0 / 8 Thermal Efficiency (T.E.) Annual Fuel Utilization Efficiency (AFUE) Temperature ise ange ( F) Hi / Low 5-65 / / / / / No. of Burners Evaporator Motor / oil Motor Type Direct Drive Direct Drive Belt Drive Belt Drive Belt Drive Indoor Nominal FM,800,800,800,800,800 Motor Speed Tap (ooling) T T Indoor Motor FLA (ooling) Horsepower - PM.0 -, , Piston Size (ooling) Filter Size (") (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" (4) 4" x 20" x 2" Drain Size (NPT) ¾" ¾" ¾" ¾" ¾" -40A efrigerant harge ir # (oz.) Evaporator oil Face Area (ft²) ows Deep / Fins per Inch 4 / 6 4 / 6 4 / 6 4 / 6 4 / 6 Belt Drive Evap Fan Data # of heels (D x ) (" x 0") (" x 0") (" x 0") Motor Sheave VL40 x ⅞ VL40 x ⅞ VL40 x ⅞ Blower Sheave / Belt AK6 X / AX52 AK6 X / AX52 AK6 X / AX52 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - PM ¼ -,075 ¼ -,075 ¼ -,075 ¼ -,075 ¼ -,075 Fan Diameter/ # Fan Blades 22 / 4 22 / 4 22 / 4 22 / 4 22 / 4 Outdoor Nominal FM,800,800,800,800,800 Face Area (ft²) ows Deep/ Fins per Inch 2 / 27 2 / 27 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type/ Stage / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 26.4 / / / / / 8.9 Electrical Data Voltage-Phase-Frequency 208/ / / Indoor Blower HP / FLA.0 / / / /.5.0 /.2 Max. External Static 0.9" 0.9".0".0".0" Outdoor Fan HP / FLA ¼ /.40 ¼ /.40 ¼ /.40 ¼ / 0.7 ¼ / 0.55 Min. ircuit Ampacity¹ 4. / / / Max. Overcurrent Protection (amps)² 60 / / / Power Supply onduit Hole.25".25".25".25".25" Low-Voltage onduit Hole ½" ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Notes Always check the S& plate for electrical data on the unit being installed. 2 SS-DS

13 Expanded ooling Data Tons Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) SS-DS

14 Expanded ooling Data Tons (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) 4 SS-DS

15 Expanded ooling Data 4 Tons Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) SS-DS 5

16 Expanded ooling Data 4 Tons (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) 6 SS-DS

17 Expanded ooling Data 5 Tons Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) SS-DS 7

18 Expanded ooling Data 5 Tons (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P MBh S/T Delta T K AMPS HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI ating conditions k = Total system power High and low pressures are measured at the liquid and suction service valves. Amps = outdoor unit amps (comp.+fan) 8 SS-DS

19 Airflow Data Tons ESP ( H2O) Standard Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP ESP ( H2O) High-Static Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Note: Tables represent dry coil without filter; to compensate for filter, add 0.08 to measured E.S.P. SFM correction for wet coil = 4%. SS-DS 9

20 Airflow Data Tons (cont.) Standard Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Note: Tables represent dry coil without filter; to compensate for filter, add 0.08 to measured E.S.P. SFM correction for wet coil = 4% SS-DS

21 Airflow Data Tons (cont.) Standard Direct Drive Horizontal Standard Direct Drive Down Shot FM Static Amps atts PM Speed Tap FM Static Amps atts PM Low Med Med Note: Assumes dry coil with filter in place; SFM correction for wet coil = 4% Speed Tap Low Med High Airflow Data 4 Tons Standard Direct Drive Horizontal Standard Direct Drive Down Shot FM Static Amps atts PM Speed Tap FM Static Amps atts PM Low Med High Speed Tap Low Med High Note: Assumes dry coil with filter in place; SFM correction for wet coil = 4% SS-DS 2

22 Airflow Data 4 Tons (cont.) Standard Belt Drive Down Shot ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Down Shot ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Note: Tables represent dry coil without filter; to compensate for filter, add 0.08 to measured E.S.P. SFM correction for wet coil = 4% SS-DS

23 Airflow Data 4 Tons (cont.) Standard Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Note: Tables represent dry coil without filter; to compensate for filter, add 0.08 to measured E.S.P. SFM correction for wet coil = 4%. SS-DS 2

24 Airflow Data 5 Tons Standard Direct-Drive Horizontal Standard Direct-Drive Down Shot FM Static Amps atts PM Speed Tap FM Static Amps atts PM T T T Speed Tap T T4 T5 Notes Assumes dry coil with filter in place; SFM correction for wet coil = 4% Five-ton models are shipped from the factory with speed tap set on T SS-DS

25 Airflow Data 5 Tons (cont.) ESP ( H2O) Standard Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP ESP ( H2O) High-Static Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Note: Tables represent dry coil without filter; to compensate for filter, add 0.08 to measured E.S.P. SFM correction for wet coil = 4%. SS-DS 25

26 Airflow Data 5 Tons (cont.) Standard Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Horizontal ESP ( H2O) Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Air Flow Pressure Drop of Down Flow Economizer Airflow Pressure Drop of Downflow Economizer for to 6 Ton offtop Units (00% eturn Air) SF, in SS-DS

27 rankcase Heater, High Efficiency MEV Air Filter Option High Efficiency MEV Air Filter Option 0.50 Flanders Pre Pleat M Air Velocity vs esistance (Test Size: 24" x 24" x 2" High apacity) " Deep esistance (in. w.g.) Air Velocity (FPM) Tonnage: Filter Nominal Size: Part Number: Order QTY: 24 x 24 x 2 060L x 20 x 2 060L x 20 x 2 060L rankcase Heater Selection Table ompressor Voltage rankcase ZP/ZPS ompressor Diameter 20V 460V 575V Heater atts 6-5.5" S 06000S S /7." 00L0007S 00L0008S 00L0009S L00020S 00L0002S 00L00022S 90 D*,DT* & DS* Tonnage ompressor Voltage 20V 460V 575V rankcase Heater atts Ton S 06000S S 40 4 Ton-5 Ton 00L0007S 00L0008S 00L0009S 70 *Includes,&H models. SS-DS 27

28 Electrical Data Tons Model Number Electrical ating ompressor ircuit ompressor ircuit 2 Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DS06XXXD 208/ DS06XXXB 208/ DS06XXXD 208/ DS06XXXH 208/ DS06XXX4B DS06XXX4H DS06XXX7B Standard - Direct Drive Standard - Direct Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive / / / /.2 45 / / / / / / / / / / / 0-9. / / / / / Tons Model Number Electrical ating ompressor ircuit ompressor ircuit 2 Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DS048XXXD 208/ DS048XXXD 208/ DS048XXXB 208/ DS048XXXH 208/ DS048XXX4B DS048XXX4H DS048XXX7B Standard - Direct Drive Standard - Direct Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive / / / / / / / / / / / / / / / / / / / / Tons Model Number Electrical ating ompressor ircuit ompressor ircuit 2 Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DS060XXXD 208/ DS060XXXD 208/ DS060XXXB 208/ DS060XXXH 208/ DS060XXX4B DS060XXX4H DS060XXX7B Standard - Direct Drive Standard - Direct Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive High Static - Belt Drive Standard - Belt Drive / / / / / / / / / / / / / /. 45 / / / / / / SS-DS

29 Dimensions TOP VIE FLUE/VENT OUTLET OMBUSTION AI INLET (AS UNITS) AS LINE ENTANE FONT VIE ALL DIMENSIONS IVEN AE IN INHES ALL DIMENSIONS AND SPEIFIATIONS AE SUBJET TO HANE ITHOUT NOTIE SUPPLY AI DUT DS THU 5 TON OMMEIAL ONDENSATE DAIN OUTLET LIFTIN SHAKLE HOLES BOTH SIDES AND ENDS FK HOLES BOTH SIDES AND BOTH ENDS IHT END VIE ETUN AI DUT SS-DS 29

30 Dimensions (cont.) ONDENSATE DAIN BOTTOM EXIT MOD TON AS, HT M 4 TON AS, HT M 5 TON AS, HT M 6 TON AS, HT M SUPPLY AI DUT ETUN AI DUT BASE PAN VIE (VIEED FOM TOP) ONDENSATE DAIN BOTTOM EXIT MODEL TONNAES "A" "B" "" TON OMMEIAL AS, HT MP, AI ONDITIONE TON OMMEIAL AS, HT MP, AI ONDITIONE TON OMMEIAL AS, AI ONDITIONE TON OMMEIAL HT MP LINE IE ENTANE "A" "" "B" T IE ENTANE LEFT END VIE UN AI DUT SS-DS ASE PAN VIE ED FOM TOP)

31 Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a clearance of 48" on all sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit Beneath any obstruction. Install the unit away from all building exhausts to inhibit ingestion of exhaust air into the unit s fresh-air intake. 48" 48" Electrical Entrance Locations 48" 48" High-Voltage Entrance (emove Plug) Low-Voltage Entrance 2⅜ ½ Dia. 0¼ Power Thru the urb Low-Voltage Entrance 47½ 7½ orner & enter-of-ravity Locations Unit eights -Ton eights 4-Ton eights 5-Ton eights 0 ondenser oil eturn Evaporator oil Supply orner eight (A) 09 orner eight (B) orner eight () orner eight (D) Unit Shipping eight Unit Operating eight ompressor 7 Note: eights are calculated without accessories installed. SS-DS

32 oof urb Installation igging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 60. Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. emove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. efer to rigging label on the unit. Important: If using bottom discharge with roof curb, duct-work should be attached to the curb prior to installing the unit. Duct-work dimensions are shown in oof urb Installation Instructions Manual. efer to the oof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National oofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. hile rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. ith condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. hen a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. To assist in determining rigging requirements, unit weights are shown below. urb installations must comply with local codes and should follow the established guidelines of the National oofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Duct-work must be constructed using industry guidelines. The duct-work must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antilevered-type curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. -D View Insulated Panels Top View 70¾ 40¼ 4 x 20 Supply Opening ⅝ x 4 eturn Opening ¾ 4 ⅜ 2 SS-DS