DCG Commercial. 15- & 20-Ton, Three-Phase

Transcription

1 DG ommercial 5- & 0-Ton, Three-Phase Packaged Gas/Electric Standard eatures -0A chlorine-free refrigerant Patented tubular heat exchanger High-efficiency scroll compressor opper tube / aluminum fin coils High- and low-pressure switches High-capacity, steel-cased filter drier Built-in filter rack with standard filters (convertible to filters) -volt terminal strip ontactor with lugs Easy to service Bottom utility entry omplies with alifornia Low NOx emissions standards AHI ertified; ETL Listed abinet eatures Heavy-gauge, galvanized-steel cabinet with UV-resistant powder-paint finish ondenser hail guards ull perimeter rail Sloped drain pan ooling apacity: 5 Tons :80,000 BTU/H 0 Tons: 0,000 BTU/h Heating apacity: 5 Tons: 50,000 BTU/H 0 Tons: 00,000 BTU/h ontents Nomenclature... Product Specifications... Expanded ooling Data... 5 Airflow Data... 9 Dimensions... 0 Wiring Diagrams... Accessories... 0 * omplete warranty details available from your local dealer or at SS-DG5 7/

2 Nomenclature D G B * * * A *,5, 7,8,9 0 5 evision Levels Major & Minor Brand actory-installed Options D Daikin X No Options A Non-powered convenience outlet onfiguration B Powered convenience outlet ommercial Low-ambient kit D eturn air smoke detector Application E Supply air smoke detector ooling Non-powered convenience outlet; G Gas Heat Low-ambient kit H Heat Pump G Non-powered convenience outlet; eturn air smoke detector Nominal ooling apacity H Non-powered convenience outlet; 0 Tons 0 8½ Tons Supply air smoke detector 08 Tons 0 0 Tons J Non-powered convenience outlet; 00 5 Tons 50 ½ tons eturn & Supply air smoke detectors 07 Tons 80 5 Tons K Non-powered convenience outlet; 090 7½ Tons 0 0 Tons Low-ambient kit; Supply air smoke detector L Non-powered convenience outlet; Nominal Heating apacity Low-ambient kit Gas/Electric A/ HP (actory-installed Electric Heat) eturn & Supply air smoke detectors 05 5,000 BTU/h XXX No Heat M Powered convenience outlet; ,000 BTU/h 00 0 kw 00 0 kw Low-ambient kit 5 5,000 BTU/h 05 5 kw 0 0 kw N Powered convenience outlet; 0 0,000 BTU/h 0 5 kw 05 5 kw eturn air smoke detector 0 0,000 BTU/h 08 8 kw 0 5 kw O Powered convenience outlet; 50 50,000 BTU/h 00 0 kw 00 0 kw eturn & Supply air smoke detectors 00 00,000 BTU/h 05 5 kw P Powered convenience outlet; See product specifications for heat size(s) available for each capacity. Supply air smoke detector Q Powered convenience outlet; Low- Voltage ambient kit; eturn air smoke detector 08-0//0 0//0 Powered convenience outlet; Low- 08-0// //0 ambient kit; Supply air smoke detector T Powered convenience outlet; Supply an/drive Type/Motor Low-ambient kit; eturn & Supply B Belt Drive air smoke detectors D Direct Drive U Non-powered convenience outlet; Low-ambient kit; eturn air smoke detector actory-installed Options V Low-ambient kit; eturn air smoke detector X No Options W Low-ambient kit; Supply air smoke detector A Downflow Economizer Y Low-ambient kit; eturn & Supply H Disconnect Switch (non-fused) air smoke detectors J Downflow Economizer; Disconnect Switch (non-fused) Z eturn & Supply air smoke detectors Note: Not all options available for all products. actory-installed Options X Standard Aluminized Heat Exchanger S Stainless-Steel Heat Exchanger actory-installed Options Stainless-Steel Heat Exchanger (PG units only): A tubular heat exchanger made of 09-type stainless steel is installed in the unit. Low-Ambient Kit: Allows for cooling operation at lower outdoor temperatures. On the - to -ton units, cooling operation is extended from 0 ambient temperature to 5 outside air temperature. On 7½- to 0-ton units, cooling operation is extended from 5 ambient temperature to 0 outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (P and PH units only): Available in all voltage options. Non-powered onvenience Outlet: A 0V, 5A, GI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 0V, 5A, GI outlet powered with a transformer built into the unit; for use when unit is not running. When a factory-installed powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.5A for 08/0V units, increase by.75a for 0V units, and by A for 575V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (non-fused): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning (P units) and heat pump models (PH units), the appropriate electric heat kit must be ordered to be factory-installed along with the disconnect switch (non-fused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (non-fused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (non-fused) is in the off position. eturn Air and/or Supply Air Smoke Detectors: eturn air and/or supply air smoke detectors are installed in the unit. SS-DG5

3 Product Specifications 5 Tons DG80 50B***A* DG80 50B***A* DG80 507B***A* ooling apacity Total, BTU/h 80,000 80,000 80,000 Sensible BTU/h 7,500 7,500 7,500 EE / IEE 0.8 / / /.0 Decibels AHI eference #s Heating apacity High Input / Output (KBTU/h) 50 / / / 80 Low Input / Output (KBTU/h).5 / 0.5 / 0.5 / 0 Steady State Efficiency (%) Temperature ise ange ( ) High/Low 0-0 / / / 0-50 No. of Burners Evaporator Motor / oil Motor Type (Belt Drive) Std Static Std Static Std Static Indoor Nominal M 5,00 5,00 5,00 Indoor Motor LA (ooling) Horsepower - PM 5.0 -, , ,75 Metering Device TXV TXV TXV ilter Size (#) 0 x 5 x () 0 x 5 x () 0 x 5 x () Drain Size (NPT) " " " -0A efrigerant harge ir # A efrigerant harge ir # Evaporator oil ace Area (ft²) ows Deep / ins per Inch / / / Belt Drive Evap an Data # of Wheels (D x W) (5" x ") (5" x ") (5" x ") Motor Sheave VP50 x ⅛" VP50 x ⅛" VP50 x ⅛" Blower Sheave 90 x ³ ₁₆" 90 x ³ ₁₆ 90 x ³ ₁₆ Belt BX BX BX ondenser an / oil Quantity of ondenser an Motors Horsepower - PM ⅓ -,075 ⅓ -,075 ⅓ -,075 an Diameter / # an Blades / / / Outdoor Nominal M 9,000 9,000 9,000 ace Area (ft²) ows Deep / ins per Inch / 7 / 7 / 7 ompressor Quantity / Type / Scroll / Scroll / Scroll ompressor LA / LA ea. 5 /. / / 78 Electrical Data / Static Voltage / Phase / requency 08-0//0 0//0 575//0 Outdoor an LA / LA. / 5.. /..9 /. Total Unit Amps Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² Entrance Power Supply ⅛" ⅛" ⅛" Entrance ontrol Voltage ⅞" ⅞" ⅞" Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Note: Always check the S& plate for electrical data on the unit being installed. SS-DG5

4 Product Specifications 0 Tons DG0 00B***A* DG0 00B***A* DG0 007B***A* ooling apacity Total, BTU/h 0,000 0,000 0,000 Sensible BTU/h 70,000 70,000 70,000 EE / IEE 9.8 / / / 0.0 Decibels AHI eference #s Heating apacity High Input / Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Low Input / Output (KBTU/h) 00 / 0 00 / 0 00 / 0 Steady State Efficiency (%) Temperature ise ange ( ) High/Low 5-55 / / / 5-5 No. of Burners Evaporator Motor / oil Motor Type (Belt Drive) Std Static Belt Drive Std Static Belt Drive Std Static Belt Drive Indoor Nominal M 7,000 7,000 7,000 Indoor Motor LA (ooling) Horsepower - PM 5.0 -, , ,75 Metering Device TXV TXV TXV ilter Size (#) 0 x 5 x () 0 x 5 x () 0 x 5 x () Drain Size (NPT) " " " -0A efrigerant harge ir #s & 00 ozs. 00 ozs. 00 ozs. Evaporator oil ace Area (ft²) ows Deep / ins per Inch / / / Belt Drive Evap an Data # of Wheels (D x W) (5" x 5") (5" x 5") (5" x 5") Motor Sheave VP0 x ⅛" VP0 x ⅛" VP0 x ⅛" Blower Sheave 00 x ⁷ ₁₆" 00 x ⁷ ₁₆ 00 x ⁷ ₁₆ Belt BX BX BX ondenser an / oil Quantity of ondenser an Motors Horsepower - PM ⅓ -,075 ⅓ -,075 ⅓ -,075 an Diameter / # an Blades / / / Outdoor Nominal M 9,000 9,000 9,000 ace Area (ft²) ows Deep / ins per Inch / 7 / 7 / 7 ompressor Quantity / Type / Scroll / Scroll / Scroll ompressor LA / LA ea.. / / 5.8 / 80 Electrical Data / Static Voltage / Phase / requency 08-0//0 0//0 575//0 Outdoor an LA / LA. / 5.. /..9 /. Total Unit Amps Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² Entrance Power Supply ⅛" ⅛" ⅛" Entrance ontrol Voltage ⅞" ⅞" ⅞" Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HA-type circuit breakers of the same size as noted. Note: Always check the S& plate for electrical data on the unit being installed. SS-DG5

5 Expanded ooling Data 5 Tons Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-DG5 5

6 Expanded ooling Data 5 Tons (cont.) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-DG5

7 Expanded ooling Data 0 Tons Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-DG5 7

8 Expanded ooling Data 0 Tons (cont.) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P MBh S/T T HI P LO P IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. 8 SS-DG5

9 Airflow Data 5 Tons ESP In" H₂O Standard Belt Drive Turns Open 0 5 M BHP M BHP M BHP M BHP M BHP M BHP M BHP ,87.75,9.79 5, ,079.09,.755,. 5, , ,90.8, ,9.0 5,.09, ,77.9, ,8.5 5, , , , ESP In" H₂O High-Static Belt Drive Turns Open 0 5 M BHP M BHP M BHP M BHP M BHP M BHP M BHP ,90.895, , , ,9.98 5, ,.80 5, , ,8.55 5,808.0, ,8.9 5,78.950, ,80.7, Airflow Data 0 Tons ESP In" H₂O Standard Belt Drive Down Shot Turns Open 0 5 M BHP M BHP M BHP M BHP M BHP M BHP M BHP , , ,.5 8,88.9 7, ,08.8 8,.858 8, ,87.5 7,.88, , , , , , ,5.70 7, ,79.09, , High-Static Belt Drive Down Shot Turns Open ESP In" H₂O 0 5 M BHP M BHP M BHP M BHP M BHP M BHP M BHP , , , , , ,.50 7, , ,8.8 8,8.50 7,95 5.8, , , , , , Notes Airflow table represent dry coil with filters installed; SM correction factor for wet coil is %. Any adjustment made to the blower should not cause the motor to draw more than the motor rated LA. Application that exceed the above could require a larger motor. Minimum rated SM is 50 per ton. High-static airflow requires installation of high kit (HSKT0) or factory-built high-static model. Unit factory shipped with the sheave set at.5 turns open. SS-DG5 9

10 Dimensions 88⁷/₃₂ ½ 50⁹/₃₂ 5⁵/₃₂ x x eturn Supply Gas Inlet Location (¾ NPT) Vertical Discharge (Top of Unit) 9⅔ ¹ ₁₀ lue Vent 0 SS-DG5

11 Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a total clearance of 75 on the main control panel side of the unit for possible removal of fan shaft, coil, electric heat, and gas furnace. Leave a clearance of 8 on all other sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit beneath any obstruction. Install the unit away from all building exhausts to inhibit Ingestion of exhaust air into the unit s fresh-air intake. minimum roof overhang Electrical Entrance Locations ¹/₈ ³/₅ High-Voltage Entrance ⁴/₅ Low- Voltage Entrance SS-DG5

12 EVAPAT OILS Product Specifications oof urb Installation igging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 0. Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. emove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. efer to rigging label on the unit. Important: If using bottom discharge with roof curb, duct-work should be attached to the curb prior to installing the unit. Ductwork dimensions are shown in oof urb Installation Instructions Manual. efer to the oof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National oofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. A Y 0 B OMPESS ompressor ompressor OMPESS 58 X G Supply Evaporator oil orner & enter-of-gravity Locations eturn D 5-Ton Units Weights 0-Ton Units Weights Weight A 58 Weight A 5 Weight B 75 Weight B 57 Weight 55 Weight 589 Weight D Weight D 8 Shipping Weight 98 Shipping Weight 57 Operating Weight 08 Operating Weight To assist in determining rigging requirements, unit weights are shown to the right. Note: These weights are calculated without installed accessories. SS-DG5

13 oof urb Installation urb installations must comply with local codes and should follow the established guidelines of the National oofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. ull perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Duct-work must be constructed using industry guidelines. The duct-work must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antilevered-type curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. urb Top O.D. 9¾ urb Top O.D. 7²/₂₅ 7²/₂₅ 7²/₂₅ 7¾ urb O.D. ⅞ ⅞ ⅞ 78 urb Top O.D. Insulated Panels ¼ ⅝ Typ. ¾ urb Bottom O.D. ⅜ Typ. ¾ 77½ urb Bottom O.D. SS-DG5

14 Product Specifications Wiring Diagram DG 5 & 0 Tons (0V Three-Phase Belt Drive) PB L L L L L L L L L POWE SUPPLY SEE NOTE 08V / 0V - ph - 0Hz SEE NOTE PL H ND VM 9 8 H 5 7 ALS S H GV EM OMP OMP T T T T T VM B T T LPS T OOL HEAT L UNUSED V HPS HPS S S G Y Y W W O H LPS T 0 08 L T DI PS TB M M M S LS II High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. ailure to do so may cause property damage, personal injury, or death. Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. EPLAE JUMPE WITH SMOKE/IE DETET SEE NOTE 5 S IGN TO THEMOSTAT SEE NOTE 7 00L0579-A SS-DG5

15 Wiring Diagram DG 5 & 0 Tons (0V Three-Phase Belt Drive) Product Specifications SUPPLY VOLTAGE 08-0//0 OMPONENT LEGEND L L L ALS AUXILLAY LIMIT SWITH T T T B OMP OWE ONTAT OMPESS T OMP M ONDENSE MOT OMPESS ONTAT H H ANK ASE HEATE ANK ASE HEATE ELAY OMPESS ONTAT ELAY EM EVAPAT MOT M USE L 5 9 B H H NOTE II T 7 EON 8 0 T EM T OMP T 08-0v PS ALS T T B V B T S IGN S S H B VM D LS M LPS LPS HPS GV M VM HPS NOTE II L AN APAIT S LAME SENS GND EQUIPMENT OUND GV GAS VALVE HPS HIGH PESSUE SWITH I INDO OWE ELAY II INTEATED IGNITION ONTOL IGN IGNIT LPS LOW PESSUE SWITH LS LIMIT SWITH PB POWE DISTUBTION OK PL EMALE PLUG/ONNET PS PESSUE SWITH S OLLOUT SWITH TB TEMINAL OK (V SIGNAL) TB TEMINAL OK (L) T TANSME VM VENT MOT VM VENT MOT ELAY NOTES. EPLAEMENT WIE MUST BE THE SAME SIZE AND TYPE O INSULATION AS IGINAL. (USE OPPE ONDUT ONLY).. AESSY EONOMIZE PLUG ADJAENT TO OWE HOUSING IN ETUN AI OMPATMENT. EMOVE MALE PLUG AND ATTAH EMALE PLUG TO THE EONOMIZE AESSY.. L AND L ON II ONTOL IS V INT.. USE OPPE ONDUTS ONLY. USE NE LASS WIE. 5. TWO STAGE OPEATION EMOVE 5. TWO STAGE OPEATION EMOVE W TO W WIE JUMPE. W TO W WIE JUMPE.. 08V OPEATION MOVE AK WIE OM TEMINAL TO TEMINAL ON THE TANSME. 7. I DD ONTOL OPTON IS INSTALLED, THEMOSTAT IELD WIING IS NOT EQUIED. SEE DD ONTOL WIING DIAAM AND INSTUTIONS. High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. ailure to do so may cause property damage, personal injury, or death. S S W Y W Y G O TO THEMOSTAT SEE NOTE 7 TB STATUS LIGHT ON O INK INKS NOTE 5 EQUIPMENT STATUS NMAL OPEATION NO POWE INTENAL ONTOL IGNITION AILUE OPEN OLLOUT SWITH OPEN AUX. LIMIT SWITH PESSUE SWITH OPEN H INSTALLE/SEVIEMAN THE STATUS LIGHT ON THE UNAE ONTOL MAY BE USED AS A GUIDE TO TOUESHOOTING THIS APPLIANE. STATUS LIGHT ODES AE AS OLLOWS: H PL SEE NOTE HEK HEK INT POWE HEK USE ON ONTOL 5 EPLAE ONTOL GAS LOW GAS PESSUE GAS VALVE LAME SENS LAME OLLOUT BAD SWITH AUX. LIMIT OPEN HEK PESSUE SWITH ATY WIING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE IELD WIING HIGH VOLTAGE LOW VOLTAGE WIE ODE AK UE OWN EEN ANGE PINK PLE ED ITE YELLOW / YELLOW WITH THEMOSTAT IELD WIING STAGE OOLING W G Y Y O TB W G Y Y O STAT Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. INKS PESSUE SWITH LOSED WITHOUT INDUE ON HEK PESSUE SWITH PINK STIP / UE WITH INKS OPEN LIMIT SWITH MAIN LIMIT OPEN BAD SWITH PINK STIP 5 INKS ALSE LAME SENSED STIKING GAS VALVE INKS OMPESS OUTT DELAY MIN. OMP. ANTI-YLE TIME SEE UNIT ATING PLATE TYPE AND SIZE O OVE UENT POTETION 00L0580-A SS-DG5 5

16 Wiring Diagram DG 5 & 0 Tons (0V/ 575V Three-Phase Belt Drive) Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. ailure to do so may cause property damage, personal injury, or death. GND H H EM OMP OMP T T T T T L L L B T L T L T L L L T T L H VM ALS S GV VM HPS HPS LPS LPS V H L L UNUSED OOL HEAT DI PS EON TO THEMOSTAT ++ 00L058-A 0 APPOPIATE INT VOLTAGE 0 0 II SEE NOTE POWE SUPPLY 0V / ph - 0 Hz SEE NOTE NOTE SEE NOTE PL TB M M M LS S S G W W Y Y O S IGN SEE NOTE 5 EPLAE JUMPE WITH SMOKE/IE DETET TB S SS-DG5

17 Wiring Diagram DG 5 & 0 Tons (0V/ 575V Three-Phase Belt Drive) L T SUPPLY VOLTAGE 08-0//0 L L T T T OMP OMPONENT LEGEND ALS AUXILLAY LIMIT SWITH B OWE ONTAT OMP OMPESS M ONDENSE MOT OMPESS ONTAT H H EM ANK ASE HEATE ANK ASE HEATE ELAY OMPESS ONTAT ELAY EVAPAT MOT M USE L 5 9 NOTE H NOTE B B T H II II 7 EON T 8 0 T EM S OMP T PS T T B V ALS B 0V 575V T H B VM D LS M NOTE T S IGN S LPS 0V 575V LPS GV HPS M VM HPS NOTE II II L AN APAIT S LAME SENS GND EQUIPMENT OUND GV GAS VALVE HPS HIGH PESSUE SWITH I INDO OWE ELAY II INTEATED IGNITION ONTOL IGN IGNIT LPS LOW PESSUE SWITH LS LIMIT SWITH PL EMALE PLUG/ONNET PS PESSUE SWITH S OLLOUT SWITH TB TEMINAL OK (V SIGNAL) TB TEMINAL OK (L) T TANSME VM VENT MOT VM VENT MOT ELAY NOTES. EPLAEMENT WIE MUST BE THE SAME SIZE AND TYPE O INSULATION AS IGINAL. (USE OPPE ONDUT ONLY).. AESSY EONOMIZE PLUG ADJAENT TO OWE HOUSING IN ETUN AI OMPATMENT. EMOVE MALE PLUG AND ATTAH EMALE PLUG TO THE EONOMIZE AESSY.. L AND L ON II ONTOL IS V INT.. USE OPPE ONDUTS ONLY. USE NE LASS WIE. 5. TWO STAGE OPEATION EMOVE W TO W WIE JUMPE. W TO W WIE JUMPE.. 575V OPEATION MOVE AK WIE OM TEMINAL TO TEMINAL ON 0V High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. ailure to do so may cause property damage, personal injury, or death. TB S S G W W Y Y O EPLAE JUMPE WITH SMOKE/IE DETET INSTALLE/SEVIEMAN THE STATUS LIGHT ON THE UNAE ONTOL MAY BE USED AS A GUIDE TO TOUESHOOTING THIS APPLIANE. STATUS LIGHT ODES AE AS OLLOWS: STATUS LIGHT ON O INK INKS INKS INKS INSTALLE/SEVIEMAN THE STATUS LIGHT ON THE UNAE ONTOL MAY BE USED AS A GUIDE TO TOUESHOOTING THIS APPLIANE. STATUS LIGHT ODES AE AS OLLOWS: STATUS LIGHT ON O INK INKS INKS INKS TO THEMOSTAT ++ SEE NOTE 5 EQUIPMENT STATUS EQUIPMENT STATUS NMAL OPEATION NMAL OPEATION NO POWE NO POWE INTENAL ONTOL INTENAL ONTOL IGNITION AILUE IGNITION AILUE OPEN OLLOUT OPEN OLLOUT SWITH SWITH OPEN AUX. LIMIT OPEN AUX. LIMIT SWITH SWITH PESSUE SWITH PESSUE SWITH OPEN OPEN PESSUE SWITH LOSED PESSUE SWITH LOSED WITHOUT INDUE ON WITHOUT INDUE ON OPEN LIMIT SWITH OPEN LIMIT SWITH H H PL NOTE 7 HEK HEK HEK INT POWE HEK INT POWE HEK USE ON ONTOL HEK USE ON ONTOL EPLAE ONTOL EPLAE ONTOL GAS LOW GAS LOW GAS PESSUE GAS PESSUE GAS VALVE GAS VALVE LAME SENS LAME SENS LAME OLLOUT LAME OLLOUT BAD SWITH BAD SWITH AUX. LIMIT OPEN AUX. LIMIT OPEN HEK HEK PESSUE SWITH PESSUE SWITH HEK HEK PESSUE SWITH PESSUE SWITH MAIN LIMIT OPEN BAD SWITH BAD SWITH ATY WIING LINE VOLTAGE LOW VOLTAGE IELD WIING HIGH VOLTAGE WIE ODE AK UE OWN EEN ANGE PINK PLE ED ITE YELLOW / YELLOW WITH PINK STIP / UE WITH PINK STIP THEMOSTAT IELD WIING STAGE OOLING W G Y Y O TB NO EONOMIZE W G Y Y O TB WITH EONOMIZE OPTION W G Y Y O TB W G Y Y O STAT W G Y O STAT W G Y O STAT Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. 5 INKS 5 INKS ALSE LAME SENSED ALSE LAME SENSED STIKING GAS VALVE STIKING GAS VALVE INKS INKS OMPESS OMPESS OUTT DELAY OUTT DELAY MIN. OMP. MIN. OMP. ANTI-YLE TIME ANTI-YLE TIME SEE UNIT ATING PLATE TYPE AND SIZE O OVE UENT POTETION 00L058-A SS-DG5 7

18 Accessories iled-installed Item # Description its Model Sizes ield- Installed B800 " oof urb 5-0 tons D5D800 5% Manual resh Air Damper 5-0 tons D5MD800 5% Motorized resh Air Damper 5-0 tons DDNBB800 Burglar Bar Sleeves with Supply and eturn All Models DK80 oncentric Duct Kit 5 tons DK0 oncentric Duct Kit 0 tons actory- Installed onvenience Outlet: Powered All Models onvenience Outlet: Non Powered All Models Disconnect Switch (non-fused) All Models DDNENJ800 Downflow Economizer 5-0 tons HAK00 High-Altitude Kit All Models HSKT80G High-Static Kit (0/0v) 5 tons HSKT80G-7 High-Static Kit (575v) 5 tons HSKT0 High-Static Kit (0/0v) 0 tons HSKT0-7 High-Static Kit (575v) 0 tons HZUB800ED Horizontal Discharge urb End Discharge 5-0 tons HZUB800SDN Horizontal Discharge urb Side Discharge; duct openings on non-service side 5-0 tons HZUB800SDS Horizontal Discharge urb Side Discharge; duct openings on service side 5-0 tons GH- Hurricane estraint lips All Models LAKT0 Low-Ambient Kit 5-0 tons LT800 LP onversion Kit 5-0 tons DPE800 Power Exhaust (08/0v) 5-0 tons DPE800 Power Exhaust (0v) 5-0 tons Smoke Detector All Models 8 SS-DG5

19 Notes SS-DG5 9

20 Notes Our continuing commitment to quality products may mean a change in specifications without notice. 0 Houston, Texas Printed in the USA. 0 SS-DG5