SPECIAL TOOLS. For all industries ALL ITEMS DIRECT DELIVERY

Transcription

1 SPECIAL TOOLS For all industries ALL ITEMS DIRECT DELIVERY

2 Content Content Chassis/Axles 3 19 Brakes Engine Wheels/Tires Body Universal Commercial vehicles: Mercedes MAN DAF Scania Volvo Iveco Renault Vans Trailers: Schmitz Cargobull Krone Kögel Fliegl Also suitable for passenger cars, buses and agricultural machinery. 2 SPECIAL TOOLS

3 CHASSIS BALL JOINT STUD REMOVER SET, 3-PIECE For passenger cars and vans, in case. To remove ball joint studs from tie rods, steering knuckles, and stabilizers, incl. reinforced version for vans. Especially suitable for work in hard-to-reach places. Suitable for: Audi, VW, BMW, Citroen Jumper, Fiat Ducato, Peugeot Boxer, MB Sprinter, Renault, Rover, Saab, Volvo, buses, agricultural machinery Art. no ,99 Also available individually: BALL JOINT STUD REMOVER To remove ball joint studs from tie rods, steering knuckles, and stabilizers, incl. reinforced version for vans. Especially suitable for work in hard-to-reach places. Jaw opening Suitable for Art. No. PU Price 23 x 55 mm Audi, VW, BMW, Citroen Jumper, Fiat Ducato, Peugeot Boxer, MB Sprinter, Renault, Rover, Saab, Volvo, various Japanese passenger car brands, agricultural machinery 28 x 55 mm Audi A4, A6, A8, VW Passat models from 1997 and Mercedes Benz, agricultural machinery x 63 mm MB Sprinter, VW LT, Opel Movano, agricultural machinery, etc SPECIAL TOOLS 3

4 CHASSIS DRIVE SHAFT SOCKET CV 41 MM HEX, ¾" DRIVE Especially adapted, impact-resistant design. For the removal and mounting of Cardan shafts. Suitable for: Citroen C25, Fiat Ducato, Peugeot J5, agricultural machinery Art. no AXLE NUT SOCKET CV 57 MM BIHEX, ¾" DRIVE Length 70 mm Suitable for: Ford Transit from 1991, axle no. 34, agricultural machinery Art. no DRIVE SHAFT SOCKET SET 6-PIECE, ½" DRIVE, BIHEX + HEX Impact wrench design consisting of: deep impact sockets sizes 30, 32, 36 mm (bihex) and impact screwdriver bits 14, 17, 19 mm (hex bits) for drive shafts. Suitable for: Any type of vehicle, agricultural machinery Art. no DRIVE SHAFT IMPACT SOCKET SET 9-PIECE, ½" DRIVE, BIHEX + HEX Thin-walled version of art. no Profile and single-piece extra-short screwdriver bits. For removal and mounting. Scope of delivery: Size 24, 27, 30, 32, 34, 36 x 85 mm (bihex socket); Size 14, 17, 19 x 43 mm (hex screwdriver bit) Suitable for: VW (Golf IV - Polo - Passat etc.), Audi, Seat, Skoda, Opel, BMW, Mercedes, Renault, Toyota, agricultural machinery Art. no SPECIAL TOOLS

5 CHASSIS GROOVE LOCK NUT SOCKET, REAR AXLE ¾" DRIVE, 6 STUDS Length x width: 52 x 8 mm Inner stud Ø 61 mm Inner Ø of base body 50 mm Outer Ø 70 mm For rear axles Suitable for: VW LT, MB Sprinter 412 D Art. no BALL JOINT SEPARATOR Heavy-duty design, ruggedized and workshop-tested For pressing out ball joint studs With hydraulic pressure spindle 10t Studs Jaw sizes Maximum Suitable for Art. No. PU Price mm Max. 90 mm 12 t MB, e.g. ATEGO up to 17t, MAN M 2000, Iveco, Renault, Scania, Volvo, DAF. Vans, e.g. VW T4, Ford Transit, MB Sprinter, Fiat Ducato, heavy-duty passenger cars, e.g. off-road vehicles mm Max. 115 mm 20 t MB, e.g. Actros, Atego from 18t, SK, O405, O405 - N (low-floor bus), MAN F 2000, TGA, low-floor articulated bus, Iveco Eurostar, Eurotech, Turbostar, Scania series 3 and 4, coaches on Scania chassis such as Icarus, DAF, Renault, Volvo PULLER FOR TIE ROD ENDS BELL SHAPE Art. No. Price Fig. Jaw opening Max. height Surface Drive Weight Application Type Art. No. PU 1 30 mm 58 mm Burnished Hex 19 mm 1.10 kg Bolt suitable for impact Light trucks t mm 90 mm Hex 26 mm 2.5 kg screwdrivers, pressure piece rotates on bolt. 39 mm 58 mm Hex 26 mm 3.85 kg Trucks, e.g. MB 1424, Actros2 SPECIAL TOOLS 5

6 CHASSIS AXLE NUT SOCKET, FLAT OVAL 36 MM HEX DRIVE, HEAVY-DUTY DESIGN For flat-oval axle nuts on BPW axles and ECO axle. Size Suitable for Art. No. PU Price 65 mm BPW axles, ECO axle 9, 10, 12t mm BPW axles, ECO axle 9, 10, 12t HUB CAP AND AXLE NUT SOCKET ¾" / 1" DRIVE, IMPACT NUT For removal/mounting of flat-oval hub cap nuts and axle nuts. Size Suitable for Art. No. PU Price ¾"/95 mm BPW axles 9t, 12t/10t ECO axle "/110 mm BPW axle 12t HUB CAP AND AXLE NUT SOCKET, FLAT OVAL ¾" DRIVE, IMPACT SOCKET For flat-oval grease caps. Size Suitable for Art. No. PU Price 65 mm BPW axles 9t, 12t and 10t ECO axle mm mm BPW axle 13 t ECO front axle mm BPW axle 9t mm BPW axle 12 t mm BPW-ECO axle AXLE NUT SOCKET CV ¾" DRIVE, 80 MM, OCTAGON, IMPACT SOCKET Suitable for: MAN, DAF 106, Scania 124 I 144 I etc. Art. no SPECIAL TOOLS

7 CHASSIS AXLE NUT SOCKET WITH OR W/O GUIDE BAND 36 MM, HEX DRIVE, HEAVY-DUTY DESIGN For rear-axle hubs with brake drums and wheels. Fig. Size Suitable for Art. No. PU Price 1 85 mm SAF trailer axles mm IVECO - Cargo rear axle mm DC trailer axle Dicos Trailers from 2005 with compact bearing HUB unit (DB no. W ) mm IVECO Euro Cargo - rear axle type 120 E15 98 with double nut mm Kässbohrer/Setra coaches Without guide band AXLE NUT SOCKET HEXAGON AND OCTAGON Fig. Drive Size Suitable for Art. No. PU 1 ¾"/square 77 mm/hex Renault ¾"/square 80 mm/hex DAF/Volvo ¾"/square 95 mm/hex Volvo ¾"/square 105 mm/hex Volvo ¾"/square 95 mm/octagon Scania ¾"/square 100 mm/octagon Scania ¾"/square 115 mm/octagon DAF/Volvo (309) (310) SPECIAL TOOLS 7

8 CHASSIS AXLE NUT SOCKET CV ¾" DRIVE, 95 MM HEX Suitable for: IVECO EUROCARGO Art. no AXLE NUT SOCKET WITH GUIDE BAND FOR USE WITH 36 MM HEX SOCKET, 110 MM BIHEX Suitable for: IVECO Eurotech - Cursor, Stralis rear axle Art. no AXLE NUT SOCKET ¾" DRIVE, 205 MM, OCTAGON Heavy-duty version for removal/mounting of dust caps and axle nuts. Size Suitable for Art. No. PU Price 60 mm Any type of truck/commercial vehicle mm mm mm Scania axle nut 124 L/144 L VA mm Any type of truck/commercial vehicle mm mm mm mm mm mm VA Volvo FH 12 and FH 16 models from SPECIAL TOOLS

9 CHASSIS AXLE NUT SOCKET FOR USE WITH 46 MM HEX SOCKET, 140 MM HEX Impact design for rotation-angle-monitored tightening, 32 mm drive for pre-tightening. Suitable for: SAF axles, 9t RSM 9042, SKRS/RZ 9042, 11242, 9037, Art. no GROOVE LOCK NUT SOCKET ¾" DRIVE Stud width No. of studs Inner Suitable for Art. No. PU Price 7.5 mm 4 52/60 mm MB M Class; front and rear axle mm / MB Actros, Atego (heavy-duty design) mm / MAN-TGA front axle, V9-82L-01 (disc * * with additional 60 mm hex BEARING SHELL ASSEMBLY KIT For the exact and centered removal and mounting of bearing shells, especially for mounting tapered roller bearings in wheel hubs without jamming them. The specially shaped jaws are spread by an adjustment bolt for optimal placing. This allows for damage-free mounting without jamming. Robust forged design, can be disassembled easily. Also suitable for use in the workshop press. Working range Ø mm. Suitable for: Passenger cars, vans, commercial vehicles, buses, agricultural and construction machinery, mechanical and plant engineering Art. no SPECIAL TOOLS 9

10 CHASSIS IMPACT SOCKET ¾" DRIVE, 27 MM BIHEX Length 112 mm Burnished for spring U bolt connections Suitable for: MB - trucks, Actros with air suspension, agricultural machinery Art. no DEEP IMPACT SOCKET ¾" DRIVE, E24, 110 MM Heavy-duty version for works on axles and brakes. Suitable for: Universal Art. no IMPACT SCREWDRIVER BIT ¾" DRIVE, 17 MM HEX For removal and mounting of the retaining screw of the upper control arm of the rear axle. Length 170 mm For hex socket screws Suitable for: MAN TGA and F2000, Citaro, MB Actros Art. no SPECIAL TOOLS

11 CHASSIS GROOVE LOCK NUT SOCKET SET MAN TGA For rear axles, with guide tube and base body Drive ¾", 60 mm hex With 6 inner studs 11.5 mm Dimensions inner stud - inner stud: mm Dimensions inner edge- inner edge: mm Total length: mm Suitable for: MAN-TGA rear axle, e.g., HY 1350 Base body Art. no Guide tube Art. no GUIDE TUBE For TGA rear axle groove lock nut socket/base body art. no Ø mm, length 140 mm Suitable for: MAN-TGA rear axle Art. no ASSEMBLY SLEEVE For MB/MAN rear axles. Outer Ø 76 mm With internal thread M 75 x 1.5 Length 185 mm Suitable for: Rear axle HL2 in MAN L series and MB Atego and Vario Art. no SPECIAL TOOLS 11

12 CHASSIS EXTENSION TUBE FOR REAR AXLE For TGA axles Length 360 mm, knurled Outer Ø 105 mm With internal thread to guide the bearing for mounting on the rear axle Thread size M 100 x 1.5 mm Suitable for: MAN rear axle HY 1350 Art. no Further groove nuts sets, base bodies and guide tubes available for the following makes: Mercedes hypoid rear axle, HL2/2, HL2/3, HL2/5, HL2/9, HL2/11, HL2/12, HL2/15, MB hypoid rear axle HL 2/14, KL2/16, KL4/1, HL4/16, HL4/17, HL4/23, HL4/28-HL4/30, HL4/4, HL4/8, HD4/6G, HO4/2, HO4/1, HO4/18 Nr. 4/4, MB hypoid axle HO 4/10, HO 4/10DL, HO 4/11DL, HO 5/3, HO 5/4, HO 5/8, HD 4/21G, HD 4/2G, HD 4/22, HD 5/3, HL 5/2, HL 5/6, MB hypoid axle HO 5/5, HL 4/01, HL4/05, HL4/06, HD4/02, HD4/03, MB palloid front axle AL 3/6, AL 3/9, MB trailing rocker shaft axles NS4/2, NS4/10, and for pinion axles HL6/1, HL6/2, HL6/3, HD6/3, MAN - VW 8.138, 8.150, 9.136, L2000, MAN hypoid (banjo-type) rear axles of the G series VW2, VW4, VW6.1, VW 6.8, MB hypoid rear axle HL2/2, HL2/7, HL2/13, MAN front axle (front drive) M series - 3 ME DI and planetary hub reduction rear axle 5 MR, 3 MR GROOVE LOCK NUT SET REAR AXLE COMMERCIAL VEHICLES ¾" DRIVE With exchangeable guide tube for removal and mounting works on the rear axle. Studs: 6, Stud width: 10.0 mm Inner Ø base body: 87.0 mm Length 65 mm Art. no Suitable accessories: Description Type Art. No. PU Price Base body of groove lock nut socket w/o guide tubes MAN, MB Atego rear axle (pinion shafts) HL2, 814 Guide tube outer Ø 49 mm, length 140 mm Vitaro Guide tube outer Ø 57 mm, length 140 mm SPECIAL TOOLS

13 GROOVE LOCK NUT SET COMMERCIAL VEHICLES ¾" DRIVE CHASSIS GROOVE LOCK NUT SET FRONT AXLE/REAR AXLE COMMERCIAL VEHICLES ¾" DRIVE With exchangeable guide tube for removal and mounting works on the front and rear axle. Studs: 6, Stud width: 11.4 mm Inner Ø base body: mm Length 140 mm Art. no With exchangeable guide tube for removal and mounting works on the front and rear axle. Suitable accessories: Description Type Art. No. PU Price Base body of socket "without" guide tubes MAN planetary hub reduction rear axle Guide tube outer Ø 51.5 mm, length 135 mm F series H7, HD7 and Guide tube outer Ø 66.5 mm, length 135 mm Hypoid rear axles F series HY-1175, HDY- 1175, HY-13110, Studs: 6, Stud width: 9.8 mm Inner Ø base body: 117 mm Suitable accessories: Description Type Art. No. PU Price Base body of socket "without" guide tubes MB Actros rear axle, HL, HL 8 Guide tube outer Ø 60 mm, length 185 mm (hypoid axle) GROOVE LOCK NUT SET REAR AXLE COMMERCIAL VEHICLES ¾" DRIVE With exchangeable guide tube for removal and mounting works on the front and rear axle. Studs: 12, Stud width: 11.4 mm Inner Ø base body: mm Suitable accessories: Description Type Art. No. PU Price Base body groove lock nut socket "without" guide tube MB planetary hub reduction Guide tube outer Ø 50 mm, length 135 mm MB planetary hub reduction rear axle (European Guide tube outer Ø 51 mm, length 85 mm axles) 10t and 13t, HL7/0, HL7/1, HL7/2, HL7/3, Guide tube outer Ø 53 mm, length 135 mm HL7/18, HO7/8, HO7/9, HL7/015, HL7/021, HD7/2, HD7/19DG, HD7/016DG, MB hub re- SPECIAL TOOLS 13

14 CHASSIS TIE ROD WRENCH SET ½" DRIVE WITH ADDITIONAL 30 MM HEX Self-clamping adapters for the safe and damagefree removal and mounting of almost all types of tie rods also in enclosed spaces. Scope of delivery: Tool mount with ½" square socket and 30 mm hex head, length 435 mm; two interchangeable adapters Ø mm and mm Suitable for: Passenger cars/vans Art. no CLAMP NUT WRENCH ½" + ¾" DRIVE Please refer to the manufacturer's specifications on how to use with torque wrench. For clamp nuts on steering knuckles. Size Type Suitable for Art. No. PU Price 32 x 36 1 Light trucks MB, 200 and 300 series x 50 2 MB commercial vehicle axles: VL /7-8, VL 1/3, 5, 6, 7, VL 1/4, from 1979, VL /8, 9, 10, VL /5, 6, 7, 8, 9, VL 2/10, 1013 S-K, 1017 S-K, e.g., Atego x 52 3 MAN/VW G series, axle V7-26l-36L, types and x 62 4 MB commercial vehicle axles: VL 2/11 in type (new lightweight series) x 68 5 Mercedes SETRA bus S 215 HDH from 1990, NEOPLAN bus from x 71 ¾" drive 60 x 76 ¾" drive 6 DAF, Kässbohrer Setra, MAN, MB axles: VL 3/8, 13, VO 3/10, VL 4/7, 9, 10 VD 4/14, VO 4/11, 13, 18, VL 4/15, 16, 19, VD 4/20 MB series: 36, 385, 387, 389, 391, 393, 395, 617, 620, 621, 622, 623, 625, 649, VO 3/10, 4/11, 13, 19 omnibus, 0303, 0305-G, 0305, Kässbohrer Setra: front axle 6.5t + 7.5t S series, SG , trailing axle S216 HDS, S228 DT 7 MAN and MB, reinforced 9t front axle VL5, MB SK front axle VL 5/1 D-9, VL 5/2 D-9, 2629 series/6x4, 2635 K/6x4, 3535 K8/x4/4, e.g., Actros with disc brakes, as well as FAUST front axle SPECIAL TOOLS

15 CHASSIS UNIVERSAL AXLE AND GROOVE NUT WRENCH HEAVY-DUTY DESIGN For the removal and mounting of axle nuts or grease caps, e.g., on truck or trailer wheel hubs. Suitable for octagon or hex nuts, groove nuts, face nuts, round nuts with drilled holes, capstan nuts, etc. Wrench with ¾" drive. Clamping range hex: mm Clamping range groove nut: mm Tightening torques of up to 700Nm possible. Scope of delivery: 1x axle and groove nut wrench, 2x adapters, round, 6 mm, 2x adapters, round, 8 mm, 2x adapters, round, 10 mm, 2x adapters, square, 6 mm, 2x adapters, square, 8 mm, 2x adapters, square, 10 mm, 1x tension chain, 1x pin key Tools delivered in plastic foam insert Art. no INSERTION TOOL Description Type Art. No. PU Dimensions Fig. Design 1 Shaft seal insertion tool for cassette seal A MB Actros front axle rear axle /30 MB front axle + tag axle ABS Design 2 Shaft seal insertion tool for sealing rings in the wheel hub Planetary hub reduction rear axle MB truck HL 7/1, HL 7/3, HL 7/18, HL 7/07, HL 7/015, HL 7/021, HD 7/2, HD 7/19DG, HD 7/01DG, HO 7/8 Series: 1219, 1413, 1417, 1419, 1424, 1617, 1619, 1621, 1624, 1926, 2219, 2226, 2626, Design 3 Shaft seal insertion tool for planetary hub reduction axles equipped with ABS and simple shaft seal in tone ring For MB, MAN, DAF and other Design 4 Insertion tool for tone ring without shaft seal on MB Actros MB Actros front axle with ABS and disc brakes, e.g., axle no For tone rings without shaft seal! SPECIAL TOOLS 15

16 CHASSIS PNEUMATIC HYDRAULIC PUMP WITH QUICK-RELEASE COUPLING ¼" NPT Pressure 700 bar 1 liter volume 2.20 m pivoted hose Suitable for: Hydraulic cylinder set 16t, 22t, 32t Art. no Using the pump allows for the hydraulic tools to be operated by a single person. With matching quick-release coupling and return stop. 1, HYDRAULIC CYLINDER SET 32T For pushing and pulling, with an operating range of approx. 113 mm. The special design allows for hitting the tie rod inserted into the piston rod while pressing to increase the loosening torque, e.g., for corroded or glued components Spindle for pulling and pressing are integrated into the piston rod A compact hydraulic unit of low weight (8.5kg) Universal tool kit for pressing out and pulling in steering knuckle bolts, joint bolts and silent blocks. Accessories included in delivery: Thread protection ring, pressure spindle M24 x 3, tie rod M22 x 2.5, nut M22 x 2.5 Suitable for: Commercial vehicles, buses, agricultural machinery, plant engineering, mechanical engineering 1, Art. no SPECIAL TOOLS

17 CHASSIS UNIVERSAL TOOL KIT For pressing out and inserting steering knuckle bolts, joint bolts and silent blocks. This kit contains all press sleeves and pieces required for works on steering knuckle bolts, joint bolts and silent blocks (also tapered types) and is suitable for most vehicles and agricultural machinery available on the market. Delivery does not include pneumatic hydraulic pump, art. no nor hydraulic cylinder set 32t, art. no ! Inside frame height 500 mm Clamping range 130, 210, 295 mm Push rods 140 x Ø 31 mm, 250 x Ø 31 mm Press piece, impact adapter, step plate to mount the pressure pipes Pressure pipes Length Inside Ø Outside/offset Ø 42 mm mm 65 mm 145 mm mm 65 mm 42 mm mm 80/90 mm 130 mm mm 80/90 mm Suitable for: Any type of commercial vehicle, buses, agricultural machinery, construction machines, plant engineering, mechanical engineering Tool kit without case Art. no , Tool kit including sturdy plastic case Art. no , Sample application of hydraulic cylinder set 32t on steering knuckle bolts, joint bolts and silent blocks SPECIAL TOOLS 17

18 CHASSIS UNIVERSAL SILENT BLOCK SET 36- OR 44-PIECE Tool kit for pulling out and in, e.g., silent blocks, anti-vibration mountings, bushes, ball bearings, shaft seals. Due to the different diameters of the pressure sleeves and matching adapters, the tool can be easily adjusted to different diameters. If required, the different sleeves can also be reshaped individually. The spindles included allow for mechanical use of the tool kit. Guide adapter and bearing ensure a safe and smooth operation. In many cases the support and pressure sleeves can also be used together with the 22t hydraulic cylinder, art. no , and the pneumatic hydraulic pump, art. no In combination with the workshop press, only the pressure sleeves and adapters are used. Delivery in high-quality blow-molded case. Operation with workshop press Suitable for: Passenger cars, commercial vehicles, buses, agricultural and construction machinery, also suitable for SUV/off-road vehicles, e.g., BMW X3, X5, X6, MB M series, Porsche Cayenne, VW Touareg Hydraulic operation with spindle 36-piece Inside Ø mm Art. no piece Inside Ø mm Art. no Mechanical operation with spindle Hydraulic cylinder set 22t For pushing and pulling, with an operating range of 70 mm Art. no SPECIAL TOOLS

19 CHASSIS UNIVERSAL COMPACT WHEEL BEARING MOUNTING TOOL Suitable for all vehicle types. For the quick, precise and damage-free mounting of compact wheel bearings. Due to its shape, the universal mounting tool can be used mechanically with a spindle, with any common hydraulic cylinder and with an arbor press. With the adjustable jaws, the tool can be quickly mounted on any compact wheel bearing diameter. Type: Can be used universally for passenger cars such as VW, Audi, Seat, Skoda, Ford, Mazda, Porsche, Volvo etc. For compact wheel bearings with a diameter of the outer bearing ring of Ø 50 mm to Ø 80 mm max. Also suitable for VW T5, VW Touareg, Porsche Cayenne, VW Crafter and MB Sprinter from Without hydraulic cylinder and spindle Art. no Sample application with spindle and open bell Compact wheel bearing bell mounted VW T5 Polo 9N Lupo Sample application with spindle and hydraulic cylinder SPECIAL TOOLS 19

20 BRAKES IMPACT SCREWDRIVER BIT ¾" DRIVE, 14 MM HEX BIT, 170 MM For hexagon socket screws. For the removal and installation of brake caliper screws on the rear axle. Suitable for: MB Actros, Citaro with HL7 + HL8 axles Hypoid Neoplan ZF and TGA wheel hubs. Art. no IMPACT SCREWDRIVER BIT ¾" DRIVE, XZN M16 X 80 MM For the removal and installation of the rear brake caliper and flywheel screws. Suitable for: VW Touareg, Mercedes Benz Atego flywheel Art. no SPECIAL TOOLS

21 BRAKES DEEP IMPACT SOCKET ¾" DRIVE, E 22 X 110 MM Designed for axles and brakes, heavy-duty version for highest demands. Suitable for: Any type of commercial vehicle Art. no (size E24 on page 10) AIR FILTER CARTRIDGE WRENCH, THREE-LEGGED ½" DRIVE For desiccant air drier cartridges of truck brakes Adjusts from mm Milled, black oxide finish Suitable for: Any type of commercial vehicle or agricultural machinery Art. no DAF RING STRIKING WRENCH 26 MM, LENGTH 160 MM For loosening the brake caliper when changing the brake discs. Suitable for: DAF trucks XF95 and XF105 Art. no SPECIAL TOOLS 21

22 BRAKES BRAKE CALIPER WRENCH ¾" DRIVE, BIHEX, 340 MM For the removal and installation of front caliper screws. Size Suitable for Art. no. PU Price 24 mm MB Atego and Actros mm MB Atego and Actros, Kässbohrer buses BRAKE DISC THICKNESS GAUGE, 0-50 MM STAINLESS STEEL, MATT FINISH, CHROME- PLATED Designed to measure the thickness of brake discs while still installed Certified according to DIN 862 Hardened, with retaining screw Suitable for: Vans, agricultural machinery Art. no BRAKE PISTON RETRACTOR SOCKET, STEEL VERSION 12 MM HEX DRIVE WITH MAGNET To reset (retract) the automatic brake piston adjustment when changing brake pads or making other repairs to the brake caliper. Suitable for: SAF, KNORR brake calipers on commercial vehicles Size Art. no. PU Price 8mm/square socket mm/hex socket mm/hex socket mm/triple square socket SPECIAL TOOLS

23 BRAKES BRAKE SHOE SPRING PLIERS HARDENDED, 500 MM Heavy-duty version For riveted and bonded brake shoes, for the removal of drum shoe return springs Suitable for: Any type of commercial vehicle or agricultural machinery Art. no GREASE CAP PLIERS For the simple and safe removal of axle grease caps. Maximum width 75 mm Length 280 mm Suitable for: Cars, vans, trailers and agricultural machinery Art. no BRAKE CALIPER HEX SOCKET FOR MAN Special extra short version, 30 mm external hex drive with spring ball retention Length 40 mm For the removal and installation of brake caliper screws without removal of the steering knuckle arm E20 for MAN TGM/Atego 9 t Art. no E24 for MAN TGM/Atego 12 t Art. no SPECIAL TOOLS 23

24 BRAKES BRAKE PISTON SPREADER Size of spreader plates: Width 100 mm, height 60 mm, thickness 7.5 mm Suitable for: Vans and light commercial vehicles Art. no SELF-LOCKING PLIERS FOR POLYAMIDE BRAKE HOSES For the installation of polyamide brake hoses Suitable for: Any type of commercial vehicle, Mercedes Benz*, trailers Ø Art. no. PU Price mm * mm mm BRAKE HOSE CUTTER FOR PLASTIC HOSES AND PROFILES Max. diameter: 25 mm, 175 mm length Suitable for: Any type of commercial vehicle Art. no SPECIAL TOOLS

25 ENGINE CYLINDER HEAD WRENCH CV ¾" DRIVE, BIHEX, NOT OFFSET, IMPACT DESIGN For loosening and tightening cylinder head bolts of commercial vehicles. Suitable for: Mercedes-Benz, MAN Size Length Art. no. PU Price 17 mm 110 mm mm 110 mm CYLINDER HEAD WRENCH CV ½" DRIVE, E 20, IMPACT DESIGN For loosening and tightening cylinder head bolts. Length: 132 mm Suitable for: MAN models F2000/F90/F8 and buses with D25/D28 engines (MAN no ) Art. no SPECIAL TOOLS 25

26 ENGINE CYLINDER HEAD WRENCH CV ¾" DRIVE, 110 MM, NOT OFFSET, IMPACT DESIGN For loosening and tightening cylinder head bolts of commercial vehicles. Size Suitable for Art. no. PU Price E18 MAN model M 2000 and buses with D08 engines E20 MAN models F8, F90, F2000 and buses with D25/D28 engines, TGA GROOVE LOCK NUT SOCKET SET CV ½" DRIVE, 4-PIECE For tightening the pressure screw on the nozzle holder. Suitable for: MAN, any type of Mercedes-Benz truck Art. no GROOVE LOCK NUT SOCKET CV ½" DRIVE, WITH 4 STUDS, 70 MM For loosening and tightening the pressure screw on the nozzle holder. 8 mm wide Inside/outside Ø: 22/29 mm Suitable for: Commercial MAN and Mercedes-Benz vehicles: M 401/421, LA, A, M 403/423, M 470h Art. no SPECIAL TOOLS

27 ENGINE GROOVE LOCK NUT SOCKET CV 32 MM HEX DRIVE, WITH 4 STUDS, 8 MM For loosening and tightening the pressure screw on the nozzle holder. Length Properties Suitable for Art. no. PU Price 125 mm With hole to lead through the connecting MAN engines and Mercedes-Benz Euro II engines of cable for EDC engines the 400 series mm With 22 mm counter nut for a secure and Commercial MAN and Mercedes-Benz vehicles: OM stable grip , 407, 409 h/ha, , /A/LA, CV SOCKET ½" DRIVE, 19 MM HEX, 200 MM For tensioning of the V-belt on the alternator. Suitable for: MAN F90, F2000, Mercedes-Benz up to SK series Art. no TS SCREWDRIVER BIT SET (5-POINT STAR) 9-PIECE, ¼" DRIVE, WITH TAMPER-PROOF HOLE On socket rail in plastic case. Suitable for: For instance, for unit pumps of Mercedes-Benz Atego, Actros and Rover immobilizer Content: TS10/15/20/25/27/30/40/45/50 Art. no SPECIAL TOOLS 27

28 ENGINE CLUTCH CENTERING MANDREL SET 6-PIECE For the quick and precise centering of the clutch. For universal use on single- and dual-plate clutches. Content: 1x each Mandrel, adjustable from Ø mm and Ø mm; Pilot bearing adapters Ø 20, 25, 27 and 30 mm Supplied in a plastic case. Suitable for: Any type of commercial vehicle, buses, agricultural or construction machinery Art. no INJECTOR LINE WRENCH, HEX ⅜" DRIVE, 70 MM, IMPACT DESIGN 90 for injection lines. Size Suitable for Art. no. PU Price 10 mm Universal mm mm mm mm mm mm mm INJECTOR LINE WRENCH, BIHEX ½" DRIVE, 100 MM, IMPACT DESIGN 90 for injection lines. Size Suitable for Art. no. PU Price 14 mm Universal mm mm mm mm mm SPECIAL TOOLS

29 ENGINE CAMSHAFT ROTATOR For the manual, precise adjustment of the engine by the recess in the ring gear. MB and MAN ½" square drive with 2 gear wheels Suitable for: Mercedes-Benz OM h/ha, , /A/LA, 427, 429, 4289, 447/h/hA and all types of 12-cylinder MAN engines Art. no MB and MAN ½" square drive with 3 gear wheels and thick sandwich plate Suitable for: Mercedes-Benz 900 series, OM , e.g. Actros and Atego as well as all 5-, 6- and 8-cylinder MAN engines (no 12-cylinder engines), equivalent to MB , MAN Art. no Scania ½" square drive Suitable for: L series type 94/114/124/144 from and R series from 2004 Art. no Volvo ½" square drive Suitable for: 6- and 12-liter engines, D9A, D12, D16C Art. no DAF ½" square drive Suitable for: XF 105 Euro 5 Art. no DAF 24 mm hex drive Suitable for: F65, F75, F85, F95, CF 65, CF 75, CF 85, XF 95 Art. no SPECIAL TOOLS 29

30 ENGINE TRANSMISSION GEAR SWITCH IMPACT SOCKET ½" DRIVE, 27 MM OCTAGON, 75 MM For instance, for electrical switches of transmissions and other applications. Suitable for: Mercedes-Benz, MAN transmissions: 16S/112/130, 160/190, Art. no CV SOCKET ½" DRIVE, 27 MM OCTAGON, 60 MM For operating transmission and axle switches. Suitable for: MAN, Mercedes-Benz Actros, SK series Art. no GEARBOX FLANGE SOCKET CV ½" DRIVE, 36 MM BIHEX, 77 MM Suitable for: Mercedes-Benz passenger car rear axle bearing W140/ truck transmissions, MB transmission G2/24/26 coupling flange Art. no SPECIAL TOOLS

31 ENGINE TRANSMISSION ENGINE OIL DIPSTICK SET 4-PIECE To measure the oil level of engines and automatic transmissions. Suitable for: Mercedes Benz engine codes: M112, 113, 646, 647, 648, 103, 104, 943, 984, 985, 111, 119, 120, 137, 603, 913, 963, 97, 604, 605, 606, 611, and Mercedes Benz transmission codes: 716.5, 722.6, Art. no Absolutely necessary after an oil change, as vehicles are now supplied by manufacturers without any oil dipsticks and instead only feature a closing plug. SEAL PULLER WITH TWO HOOK SHAPES For the removal of sealing rings, O rings and shaft seals of any type. Length x width: 315 x 85 mm Suitable for: Any type of passenger car or commercial vehicle, buses, agricultural and construction machinery, mechanical and plant engineering Art. no SPECIAL TOOLS 31

32 ENGINE FUEL INJECTION SYSTEM/FUEL INJECTION PUMP SOCKET CV ½" DRIVE, 10 MM BIHEX, 110 MM For removal and mounting of the fuel injection pump. Suitable for: Mercedes-Benz Actros Art. no FUEL FILTER WRENCH ½" DRIVE, 95 MM 14PT For removal and mounting of the fuel filter in accordance with the torque values specified by the manufacturer. Suitable for: MAN-TGA, Mercedes-Benz Actros, agricultural machinery Art. no Ad-Blue FILTER SOCKET ⅜" DRIVE, 45 MM HEX, 65 MM For removal and mounting of the filter housing cap, for changing the filter element of Ad-Blue filters in commercial Mercedes-Benz vehicles with Blue Tec engine technology. Please observe the tightening torque of 23Nm recommended by the manufacturer. Suitable for: Mercedes-Benz new Actros, Atego, Axor, Econic Art. no SPECIAL TOOLS

33 ENGINE RADIATOR ENGINE COOLING SYSTEM TESTER SET FOR COMMERCIAL VEHICLES ALUMINUM VERSION, 9-PIECE For leakage tests of cooling systems. Scope of delivery: 1 Pressure pump with quick-release coupling, 1 flexible hose with quick-release coupling, 6 adapters Supplied in a plastic case Suitable for: Scania 113/114/124/125, DAF XF 95/XF 105, Mercedes-Benz Actros/Atego/Axor, Iveco Daily 2000-C series, MAN L 200-TGA, Volvo FH 12, MB Sprinter up to 2006 Art. no FILTER STRAP WRENCH FOR COMMERCIAL VEHICLES ½" For removal and mounting of air and water filter cartridges. Suitable for: Any type of commercial vehicle, construction and agricultural machinery Clamping range Art. no. PU Ø mm Ø mm SPECIAL TOOLS 33

34 ENGINE OIL SERVICE EXTRA STRONG OIL FILTER CHAIN WRENCH ½" DRIVE Suitable for: Universal Chain links Ø Art. no. PU Price mm mm mm OIL FILTER STRAP WRENCH ½" DRIVE Clamping range: mm Band width: mm Suitable for: Universal Art. no OIL FILTER WRENCH ½" DRIVE For removal and mounting. Size Suitable for Art. no. PU Price 94 mm, 14pt MAN 403, * mm, 15pt MAN 8 10t types: L2000, LE, M2000, ME, also suitable for, e.g., MANN filter W mm, 18pt MAN 18 48t types: TGA, F 2000, FE, , , also suitable for, e.g., MANN filter HU 1381x * Please observe maximum torque of 25Nm during installation 34 SPECIAL TOOLS

35 ENGINE OIL SERVICE/EXHAUST ENGINE OIL FILTER CAP SET 9-PIECE, 36 MM 108 MM Scope of delivery: 1x each oil filter strap wrench, single-end box wrench size 22 mm, cap wrench size 36/hex, size 76/14pt., size 106/15pt., size 107/15pt., size 108/15pt. and size 108/18pt., all oil filter wrenches with hex head drive size 22 SW22 mm and ½" socket square drive Suitable for: Universal Art. no OIL FILTER CAP WRENCH ⅜" DRIVE, 36 MM HEX For removal and mounting of the oil filter housing cap when changing the oil filter cartridge. Suitable for: Mercedes-Benz Actros MP1, MP2; 100D van engine 116 MB, E 250 D, M 605, M 606, E 300 D, E 220 D, C 220 D, C 250 D; MAN, e.g. TGA (fuel filter); BMW M5 2 6 cylinders, 3 series + 09/95, 5 series + 96, M6 0 8 cylinders, M cylinders, 8 series, 118 D, 120 D, 1 series (E87); VW Lupo 1.2 TDI, VW Touareg TDI, VW T5 2.5 D Art. no CHAIN PIPE CUTTER SPECIAL STEEL, NICKEL-PLATED For copper, brass and thin-walled steel pipes, plastic-coated pipes and exhaust silencers Stainless steel pipes with up to 2.5 mm wall thickness and Ø 60 mm Extra long chain allows for larger cutting diameter Suitable for: Universal Art. no Replacement chain: Art. no SPECIAL TOOLS 35

36 WHEELS/TIRES FOUR-WAY CV LUG WRENCH HEXAGON For loosening and tightening wheel nuts of commercial vehicles. Welded and hardened version, painted Heavy-duty version for professional use Suitable for: Commercial vehicles, buses, construction and agricultural machinery Drive Length Art. no. PU Price 19 x 22 x 24 x 27 mm 550 mm (¾ x ⅞ x ¹⁵ ₁₆ x ¹ ¹ ₁₆") 24 x 27 x 32 x 38 mm 750 mm x 27 x 30 x 32 mm + ¹³ ₁₆" 750 mm x 30 x 32 x 33 mm 750 mm x 30 x 32 x 33 mm (¹ ¹ ₁₆ x ¹ ³ ₁₆ x ¹ ¹ ₄ x ¹ ⁵ ₁₆" ) 750 mm * * Robust, welded version, DIN 3119, fully hardened, chrome-plated, designed for heavy-duty applications. IMPACT SOCKET CV ¾" DRIVE, 33 MM HEX, 90 MM LENGTH For loosening and tightening wheel nuts of commercial vehicles. Suitable for: Any type of commercial vehicle, especially Scania Art. no SPECIAL TOOLS

37 WHEELS/TIRES WHEEL NUT SOCKET DEEP IMPACT HEXAGON SOCKET For loosening and tightening wheel nuts of commercial vehicles, buses, construction or agricultural machinery without extension. Suitable for: Any type of commercial vehicle or truck Size Drive Length Art. no. PU Price 27 mm ¾" 270 mm mm ¾" 270 mm mm ¾" 270 mm mm ¾" 400 mm mm ¾" 400 mm mm ¾" 400 mm mm ¾" 400 mm mm 1" 400 mm mm 1" 400 mm mm 1" 400 mm mm 1" 400 mm CENTERING PIN SET ½" 3-PIECE, 115 MM LENGTH For the removal and mounting of centered drop-center wheels of commercial vehicles. No damage to the thread and exact centering of the rim due to tapered pins. Bolt hole Lug bolt Suitable for Art. no. PU Price 21 mm M18 x 1.5 mm DAF, IVECO, MAN, RVI (Renault), Unimog, Volvo mm mm M20 x 1.5 mm Scania M22 x 2.50 mm M22 x 1.5 mm DAF, Ford, MAN, Mercedes-Benz, Renault, Scania, Volvo ⁷ ₈" 11G Scania, Volvo ⁷ ₈" 14G Volvo alloy rims SPECIAL TOOLS 37

38 BODY SPECIAL BODY SEAM SPLITTER SET, EXTRA SLIM FOR LEFT- AND RIGHT-HAND USE OFFSET For the separation of body parts and spot-welded panels, especially back doors, side doors, etc. Concave side edge Dimensions L x W x H: 290 x 25 x 7 Suitable for: Passenger cars, commercial vehicles, buses, agricultural machinery, mechanical and plant engineering Art. no TS STAR SCREWDRIVER SET (5-POINT) WITH TAMPERP-ROOF HOLE, 8-PIECE SET For TS five-point screws, 220 mm length, with ergonomic plastic handle For loosening and tightening security screws. Content: TS 10, 15, 20, 25, 27, 30, 40, 45 Suitable for: Injection pumps, rear lights of MB Atego, Actros, MAN, Rover immobilizer system, Smart interior and exterior panels, Audi, VW and Fiat air flow meters Art. no SPECIAL TOOLS

39 BODY MECHANIC TORQUE WRENCH ¾" DRIVE Precision setting, according to DIN EN ISO 6789:2003 Easy and accurate settings due to turnable handle, robust steel version Reversible square drive for left- and right-hand operation Reaching the desired torque is indicated by an acoustic and palpable click, preventing additional tightening After use, relax spring and set to lowest torque value With calibration certificate, Quality "Made in Germany" Fig. Drive Measuring range Scale div. Length Weight Head Ø Art. no. PU Nm lbf. in. Nm mm g mm 1 ¾" ,010 4, SPECIAL TOOLS 39

40 BODY WIPER ARM PULLER WITH SPECIAL HOOKS AND LOCKING FEATURE Max. opening/clearance: 0 60 mm/up to 50 mm Perfect wiper arm removal due to integrated locking feature. The locking bolt securely fastens the hooks to the wiper arm ensuring safe removal of the wiper arm. Suitable for: Passenger vehicles, vans, buses, construction and agricultural machinery Art. no IMPACT SOCKET ½" DRIVE, 25 MM BIHEX, 45 MM LENGTH For the attachment of metal bumpers Suitable for: Any type of commercial vehicle, especially MAN trucks Art. no PROFESSIONAL HAND RIVET TOOL For aluminum and steel rivets as well as threaded rivets. Foldable handles, supplied with plastic case, incl. accessories. Aluminum/steel: 3.2; 4.0; 4.8; 5.0; 6.4 mm/m4; M5; M6; M8; M10 Suitable for: Any type of passenger vehicle, commercial vehicle, metalworking applications, installations, construction, maintenance workshops, fittings Art. no SPECIAL TOOLS

41 BODY PRY BAR SET 4-PIECE Available in four different versions: Straight, 930 mm length Straight, 30 offset and extra-wide blade, 920 mm length Straight, 60 offset, 650 mm length Straight, 90 offset, 640 mm length Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, maintenance workshops Art. no TAPER PIN PUNCH, US ALLOY STEEL, EXTRA LONG HEXAGON SHAFT AND TAPERED TIP Suitable for: Any type of passenger vehicle, commercial vehicle, metalworking applications, installations, construction, maintenance workshops Ø Length Art. no. PU Price mm 280 mm mm 460 mm PARALLEL PIN PUNCH SET, 5-PIECE US ALLOY STEEL 3, 4, 5, 6, 8, EXTRA LONG TIPS, 110 MM Suitable for: Any type of passenger vehicle, commercial vehicle, metalworking applications, installations, construction, maintenance workshops Art. no SPECIAL TOOLS 41

42 UNIVERSAL IMPACT BIT SET CV 10-PIECE, ¾" DRIVE Suitable for: universal applications Contains: one bit each for 14mm, 17mm, 19mm, 22mm and 24mm hexagon socket screws; for Torx screws T70, T80, T90 and T100 plus ¾" bit holder Art. no IMPACT BIT SET 16-PIECE, ¾" AND 1" DRIVE Bits made from chrome molybdenum steel, black oxide finish. Contains: 13 bits with 22mm hexagon drive, Torx T60/T70/T80/ T90/100, 17/19/22/24 mm hex bits, external Torx E18/E20/E22/ E24, 2 bit holders with ¾" and 1" drive, 1 hex key to fasten the bits. Suitable for air impact drivers. Art. no SPECIAL TOOLS

43 UNIVERSAL STANDARD DRUM KEY 320 MM For all standard drum caps. Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, company workshops, fittings, woodworking applications Art. no FLEXIBLE RATCHET EXTENSION DRIVE WITH REINFORCED HINGES To access hard-to-reach locations and still apply high torques! Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, company workshops, fittings, woodworking applications ⅜" drive, 235 mm length, max. angle 180, 178 Nm Art. no ½" drive, 225 mm length, max. angle 90, 351 Nm Art. no SPECIAL TOOLS 43

44 UNIVERSAL SPECIAL SCREWDRIVER BIT SET CV 38-PIECE, ¼" + ½" DRIVE Contains: 1 piece each ¼" drive: TS drive (five-point) TS10/15/20/25/27/30/40/45/50 x 30 mm ½" drive: Ribe profile R7 x 240/R8 x 240/R9 x 100/R10 x 140 mm Torx drive T40/T45/T50/T55/T60/T70 x 140 mm XZN drive M9 x 100/M10 x 140/M12 x 140/M14 x 140 mm Hex drive 7mm x 230/10 mm x 140/11 mm x 140/13 mm x 140/14 mm x 55/17 mm x 55/19 mm x 55/22 mm x 55/24 mm x 55 mm Special ½" bits: Tamper-proof XZN bit M16 x 55 mm, XZN bit M16 x 100, impact XZN bit M18 x 78 mm, Torx bits T80 x 100/T30 x 300 mm both tamper-proof, hex bit 5 x 160 mm with ball head Art. no IMPACT SCREWDRIVER BIT SET 9-PIECE, ½" DRIVE With ball-retaining groove and hole Suitable for impact wrenches, 78 mm length Torx Contains: 1 piece each Torx drive T20/T25/T30/T40/T45/T50/T55/T60/T70 For Torx screws Art. no Hex Contains: 1 piece each 4/5/6/8/10/12/14/17/19 mm Art. no SPECIAL TOOLS

45 UNIVERSAL IMPACT SCREWDRIVER BIT SET CV 6-PIECE, ½" DRIVE XZN drive M14/M16/M18 Black oxide finish 43 and 75 mm lengths on socket rail Art. no IMPACT SCREWDRIVER BIT ¾" DRIVE, 76 MM For hexagon socket screws. Size Suitable for Art. no. PU Price 12 mm Mercedes-Benz: e.g. brake pads/ brake discs Audi/Seat/Skoda/VW: e.g. drive train components 14 mm Universal mm Mercedes-Benz: e.g. brake pads/ brake discs 19 mm Audi/Seat/Skoda/VW: e.g. drive train components IMPACT SCREWDRIVER BIT ¾" DRIVE, BLACK OXIDE FINISH, EXTRA LONG For highest demands Applications include: axles and brakes For use on hard-to-reach fasteners Size Suitable for Art. no. PU Price T 60 x 130 Various applications, especially Mercedes-Benz Actros brake discs, brake calipers, pitman arms T 70 x For Torx drives SPECIAL TOOLS 45

46 UNIVERSAL IMPACT SCREWDRIVER BIT ½" DRIVE, SOLID, DESIGNED FOR SPECIAL APPLICATIONS, TORX Suitable for: Any type of commercial vehicle, especially Mercedes-Benz and MAN Size Length Art. no. PU Price T30 55 mm mm IMPACT SCREWDRIVER BIT ¾" DRIVE, TORX For fasteners on brake calipers/brake discs, differential housings/drive shafts and steering gears. Suitable for: Any type of commercial vehicle, especially Mercedes-Benz and MAN Size Length Art. no. PU Price T mm mm T70 80 mm T80 80 mm T90 80 mm T mm IMPACT SCREWDRIVER BIT CV ½" DRIVE, TORX Heavy-duty version with exchangeable bit For the highest quality requirements Suitable for: Any type of commercial vehicle or truck Size Length Art. no. PU PRICE T30 80 mm T40 80 mm T45 80 mm T50 80 mm T55 80 mm T60 80 mm SPECIAL TOOLS

47 UNIVERSAL IMPACT SOCKET ¾" DRIVE, BIHEX, HEAVY-DUTY VERSION Suitable for: Any type of commercial vehicle, especially Mercedes-Benz Atego Size Length Art. no. PU Price 17 mm 50 mm mm 50 mm mm 53 mm mm 100 mm mm 100 mm EXTERNAL THREAD REPAIR SET NES123 FOR EXTERNAL THREADS MM + ⁵ ₃₂" 6" Easy to adjust to any thread diameter and any thread pitch No additional calibration necessary Suitable for left- and right-hand threads For metric and American thread standards with 60 thread angles Delivered in blow-mold case Also available individually: NES1, 4-18 mm + 5/32" - 11/16" Art. no Suitable for: Various applications, passenger vehicles, commercial vehicles, metalworking applications, installations, construction, maintenance workshops Contains: 3 external thread repair tools: 1 NES mm + ⁵ ₃₂" ¹¹ ₁₆" 1 NES mm + ¹¹ ₁₆" 1 ½" 1 NES mm + 1 ¼" 6" 3 pairs of replacement blades and one manual deburring tool NES2, mm + 11/16" - 1 ½" Art. no Art. no NES3, mm + 1 ¼" - 6" Art. no SPECIAL TOOLS 47

48 UNIVERSAL CIRCLIP PLIERS, MAXI For internal and external circlips Robust design, made of US spring steel With ratchet mechanism and exchangeable, hardened, smoothed and polished tips for greater durability Contains: straight nose pliers Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, maintenance workshops Version Ø Tips mm Length mm Ø int./ext. circlip in mm Art. no. PU Price Internal int External ext Internal int External ext UNIVERSAL EXTENSION FORGED STEEL For the loosening of overtightened bolt connections in hard-to-reach places. Suitable for spanners, ring spanners, offset ring spanners, etc. also suitable as extension for hexagon keys such as inside hex, Torx, XZN or Ribe Integrated ½" square socket in the handle Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, maintenance workshops Total length: 340 mm for spanner sizes of up to 27 mm Art. no Total length: 580 mm for spanner sizes of up to 50 mm Art. no SPECIAL TOOLS

49 UNIVERSAL SQUARE SOCKET KEY 60 MM Made from malleable cast iron Nickel-plated with oval handle Suitable for: Mercedes-Benz and MAN buses 8 mm; length: 60 mm Art. no Suitable for: Truck storage cabinets 9 mm; length: 60 mm Art. no TRIANGLE SERVICES KEY 7 MM, ALUMINUM For the removal of the upper housing of fuel truck connectors Art. no STRIKING RING WRENCH Material: special steel Standards: DIN 7444 Size Length Art. no. PU Price 75 mm 330 mm mm 360 mm mm 360 mm mm 390 mm mm 390 mm mm 420 mm SPECIAL TOOLS 49

50 UNIVERSAL INSPECTION CAMERA, BASIC 7-PIECE, WITH 5.5 MM X 1 M SEMI-RIGID CAMERA CABLE Quick and simple visual inspection of damage in hard-to-reach places without any expensive or time-consuming disassembly being required (e.g. rocker panels, engines, gearboxes, axles, cavities, cable ducts and many other applications). 4 powerful mini LEDs with brightness control Portable, battery-powered system Direct connection through AV socket and connecting cable Camera head made of scratch-resistant sapphire glass to ensure maximum image quality and protect camera and lens Additional mirror extensions to increase the field of vision Digital zoom and mirror effect Art. no Contains Description Art. no. PU Price Video camera head, 5.5 mm, semi-rigid, Mirror attachment 70 x 5.5 mm Mirror attachment 90 x 5.5 mm Mirror attachment 110 x 5.5 mm Hook attachment 5.5 mm Magnet attachment 5.5 mm Hand-held device 1 AV cable V AA alkaline battery Technical data 2,4 TFT LCD QVGA color display Resolution: 320 x 240 pixels Weight 1,704 grams/set Video out format NTSC & PAL Angle of view: Horizontal angle 46 Vertical angle 34 Diagonal angle 56 Depth of field (DOF) At a distance of 1-6 cm Camera head IP67-certified water-resistant Suitable accessories: Description Art. no. PU Price Video camera head, 5.5 mm, flexible, Video camera head, 3.9 mm, semi-rigid, SPECIAL TOOLS

51 UNIVERSAL INSPECTION CAMERA PRO 10-PIECE, WITH 5.5 MM X 1 M SEMI-RIGID CAMERA CABLE For the inspection and documentation of hard-to-reach areas in the automotive, HVAC, construction, industry and aviation sector as well as for police and customs authorities with video recordings and/or photos as well as a live view through the TFT color screen and storage directly on the SD card. Recording function: Images in JPG and videos in NTSC or PAL format Powerful battery: 2 hours charging for 4 hours continuous use Optimum image quality due to 4 powerful mini LEDs with brightness control Portable, battery-powered system USB connection Direct connection through AV socket and connecting cable Camera head made of scratch-resistant sapphire glass to ensure maximum image quality and protect camera and lens Additional mirror extensions to increase the field of vision Digital zoom and mirror effect Art. no Contains Description Art. no. PU Price Video camera head, 5.5 mm, semi-rigid, Mirror attachment 70 x 5.5 mm Mirror attachment 90 x 5.5 mm Mirror attachment 110 x 5.5 mm Hand-held device - 1 AV cable - 1 Charger: output 5.5 V, 1.8 A (10 Watt max.) - 1 Input: V/50 60 Hz/0.5 A USB cable GB memory card - 1 Cleaning set - 1 Plastic case 535x300x85 mm - 1 Suitable accessories: Description Art. no. PU Price Hook attachment 5.5 mm Magnet attachment 5.5 mm Video camera head, 5.5 mm, flexible, Video camera head, 3.9 mm, semi-rigid, Technical data Battery Li-polymer 3.7 V (AC V/50 60 Hz) Display 3.5 TFT LCD QVGA Image format JPEG (640 x 480) Resolution H/V (325/250) Operating temperature 0 55 C Menu languages 26 Camera head 1 m x 5.5 mm semi-rigid, IP67 water-resistant Angle of view: Horizontal angle 46 Vertical angle 34 Diagonal angle 56 Mirror attachments 70, 90, 110 angle Depth of field (DOF) At a distance of 1-6 cm Weight 2250 grams/set SPECIAL TOOLS 51