EXW Unit Total EXW Measurement. Sets 2

Transcription

1 1 2 (I) SWITCHYARD PART Supply and Erection of 220kV Switch Yard Equipments (as per respective Technical Specifications and relevant special conditions A ) suitable for 2 Bus system 220 KV Indoor GIS Equipment (Separate Enclosure for Each Phase 1 shall be considered) 3- Ø 220 kv, 2000 A, 40 ka-3 sec, metal enclosed SF6 Gas Insulated 1.1 Switchgear - Line bay Module comprising Sets 6 Circuit breaker Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Current transformer /1A ( no. of cores as per TS) -1 no for each phase Line side Disconnector with one maintenance earthing switch High speed/fast Acting Line Earthing switch Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing switch SF6 Gas Insulated Bus Duct (GIB) from respective GIS bay module up to SF6 to Air insulated polymer housed bushings including required support structures and other accessories LCC Panel All other items as per technical specification 3- Ø 220 kv, 4000 A, 40 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Bus bar Module comprising Sets 2 3 X Single phase Voltage transformer 220KV/ SQRT 3//110V/ SQRT 3 -( no. of cores as per TS) sagrigated from bus bar unit High speed/fast Acting Earthing switch Bus Disconnector with Earthing switch All other items as per technical specification 3- Ø 220 kv, 2000 A, 40 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Bus Coupler bay Module comprising Set 1 Circuit breaker Current transformer /1A ( no. of cores as per TS) -1 no for each phase Bus Disconnector with one Earthing switch -2 nos. LCC Panel All other items as per technical specification 3 4 5=3X4 6 = % Excise Duty 7= (3X4X6) 8= % sales & other taxes 9=(5+7) X 8 10=(5+7+9) Ø 220 kv, 2000 A, 40 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - 220/132 KV Transformer bay Module comprising Circuit breaker Sets 2

2 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Current transformer /1A ( no. of cores as per TS)-1 no for each phase Transformer side Disconnector with one maintenance earthing switch Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing switch SF6 Gas Insulated Bus Duct (GIB) from respective GIS bay module up to SF6 to Air insulated polymer housed bushings including required support structures and other accessories LCC Panel All other items as per technical specification Ø 220 kv, 2000 A, 40 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - 220/66 KV Transformer bay Module comprising Circuit breaker Current transformer /1A ( no. of cores as per TS)-1 no for each phase Transformer side Disconnector with one maintenance earthing switch Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing switch SF6 Gas Insulated Bus Duct (GIB) from respective GIS bay module up to SF6 to Air insulated polymer housed bushings including required support structures and other accessories LCC Panel All other items as per technical specification Sets KV Outdoor Equipment 2.1 Polymer housed Surge Arrester 198kV, 10kA, Cl-3 with structure and clamp connectors s kV Bus Post polymer housed Insulator with structure and clamp connectors s kV High Bus Post polymer housed Insulator with structure and clamp connectors s kV SF6 to Air insulated polymer housed bushing 1- Phase with structure and clamp connectors s. 33 Supply and Erection of Material for 220kV Switch Yard (as per B respective Technical Specifications and relevant special conditions ) suitable for 2 Bus scheme. 1 Gantry structures GI as per BOM, Steel & A/B part MT 46 2 Gantry structures GI as per BOM, Bolt nut part MT 2.6 te: The weight of structure may vary as per actual weight of double tier ganty. 3 Lighting Mast structure - Steel & A/B part MT 13.53

3 4 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Lighting Mast structure - Bolt nut part MT 0.54 te: The weight of LM structure may vary as per actual requirement of LMs. Stringing of Flyover bus with Following Conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, spacers provided at every 5.0 mtr. interval (Suitable for 350mm spacing)etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement. 4.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor Rmtr. 360 Silicon Rubber Insulator string-120kn. 48 Double Tension H/W & Acc with Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 12 Double Tension H/W & Acc without Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 12 Spacers suitable for Twin AL59(61/3.50) Cond. (350mm Spacing). 36 Droppers (including required suspension string with hardware & accessories, if any) & Jumpers (including Equipment to Equipment) with 5 Following conductor as per standards and approved drawings with provision of required spacers (Suitable for 350mm spacing) at every 5.0 mtr. interval. 5.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor RMtr 1080 Silicon Rubber Insulator string-120kn. 27 Single Suspension H/W & Acc. Twin AL59(61/3.50) Cond.. 27 Spacers suitable for Twin AL59(61/3.50) Cond.(350mm Spacing). 108 Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to AL59(61/3.50) conductor B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor RMtr 540 Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to Line conductor. 30 C Supply and Erection of 132kV Switch Yard equipments as per respective Technical Specifications and relevant special conditions suitable for Single Main bus Scheme with Twin Zebra ACSR and relevant flyover bus with Twin Zebra ACSR conductor 1 Surge Arrester 120kV, 10kA, Class 3 with str and clamp connectors as per Technical spec. 9 2 PT 132kV/v3-/110V/v3-3C with structure and clamp connectors. 0 3 BPI 6kN with str and clamp connectors as per Technical spec HBPI 6kN with str and clamp connectors as per Technical spec. 6 5 HDB Isolator with ES 1600A 40kA 3S with str and clamp connectors as per Technical spec Set 1 6 HDB Isolator without ES 1600A 40kA 3S with str and clamp connectors as per Technical spec Set 5

4 7 8 9 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country CT /1A, 5C 40kA 3S with str and clamp connectors as per Technical spec. 3 CT /1A, 5C 40kA 3S with str and clamp connectors as per Technical spec. 6 CB 1600A 40kA 3S with str and clamp connectors as per Technical spec Set 3 D Supply and Erection of 132kV Switch Yard Material as per respective Technical Specifications and relevant special conditions suitable for Single Main bus Scheme with Twin AL59(61/3.50) and relevant flyover bus with Twin AL59(61/3.50) conductor 1 Gantry structures GI as per BOM, Steel & A/B part. MT Gantry structures GI as per BOM, Bolt nut part. MT Stringing of Main bus with Following Conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, spacers provided at every 4.0 mtr. interval (Suitable for 350mm spacing)etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement. 3.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor Rmtr. 327 Silicon Rubber Insulator string-120kn. 12 Double Tension H/W & Acc with Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Double Tension H/W & Acc without Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Spacers suitable for Twin AL59(61/3.50) Cond. (350mm Spacing) Stringing of Flyover bus with Following Conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, 4 spacers provided at every 4.0 mtr. interval (Suitable for 350mm spacing)etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement. 4.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor Rmtr. 189 Silicon Rubber Insulator string-120kn. 12 Double Tension H/W & Acc with Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Double Tension H/W & Acc without Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Spacers suitable for Twin AL59(61/3.50) Cond. (350mm Spacing) Droppers (including required suspension string with hardware & accessories, if any) & Jumpers (including Equipment to Equipment) with 4 Following conductor as per standards and approved drawings with provision of required spacers (Suitable for 350mm spacing) at every 4.0 mtr. interval. 4.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor RMtr 540 Silicon Rubber Insulator string-120kn. 9

5 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Single Suspension H/W & Acc. Twin AL59(61/3.50) Cond.. 9 Spacers suitable for Twin AL59(61/3.50) Cond.(350mm Spacing) Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to AL59(61/3.50) conductor B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor RMtr 120 Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to Line conductor. 18 Supply and Erection of 66 kv Switch Yard Equipments (as per respective Technical Specifications and relevant special conditions E ) suitable for 2 Bus system 1 66 KV GIS Indoor Equipment Ø 66 kv, 1600 A, 25 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Line bay Module comprising Sets 7 Surge Arrester 60kV, 10kA, Class 3 suitable for connection of 66kV Power Cable-1 no for each phase Circuit breaker Current transformer /1A ( no. of cores as per TS) Line side Disconnector with one maintenance earthing switch High speed/fast Acting Line Earthing switch Voltage Transformer, 66KV/ 3//110V/ 3, 3 C Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing Switch LCC Panel All other items as per technical specification 3- Ø 66 kv, 2000 A, 25 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Bus bar Module comprising Sets 2 3 X Single phase Voltage transformer 66KV/ SQRT 3//110V/ SQRT 3 - sagrigated from bus bar unit High speed/fast Acting Earthing switch Bus Disconnector with Earthing switch All other items as per technical specification 3- Ø 66 kv, 1600 A, 25 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Bus Coupler bay Module comprising Set 1 Circuit breaker Current transformer /1 ( no. of cores as per TS) Bus Disconnector with one Earthing switch -2 nos. LCC Panel All other items as per technical specification Ø 66 kv, 1600 A, 25 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - 220/66 KV Transformer bay Module comprising Sets 3

6 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Surge Arrester 60kV, 10KA, Class 3 suitable for connection of 66kV Power Cable -1 no for each phase Circuit breaker Current transformer /1A ( no. of cores as per TS) Transformer side Disconnector with one maintenance earthing switch Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing Switch LCC Panel All other items as per technical specification F Ø 66 kv, 1600 A, 25 ka-3 sec, metal enclosed SF6 Gas Insulated Switchgear - Interconnecting Line bay Module comprising Surge Arrester 60kV, 10kA, Class 3 suitable for connection of 66kV Power Cable-1 no for each phase Circuit breaker Current transformer /1A ( no. of cores as per TS) Line side Disconnector with one maintenance earthing switch High speed/fast Acting Line Earthing switch Voltage Transformer, 66KV/ 3//110V/ 3, 3 C Bus Disconnector with Earthing switch (Bus side common earthing switch for two bus) Bus Disconnector without Earthing Switch LCC Panel All other items as per technical specification Sets 2 66kV High Bus Post Insulator with structure and clamp connectors suitable for connection of 66kV Power Cable and Single/Twin AL59(61/3.50) Cond. s. 9 Supply and Erection of 66kV Switch Yard Equipments as per respective technical specifications and relevant special conditions suitable for One Main Bus with Twin AL59(61/3.50) conductor scheme Surge Arrester 60kV, 10KA, Class 3 with structure and clamp connectors suitable for Twin AL59(61/3.50) Cond.. 6 BPI 4kN with structure and clamp connectors suitable for Twin AL59(61/3.50) Cond.. 6 HDB Isolator without ES 2000 A 25kA 3s with structure and clamp connectors suitable for Twin AL59(61/3.50) Cond. Set. 4 CT /1 3C 31.5KA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) Cond.. 6 CB 1600A 25kA 3S with structure and clamp connectors suitable for Twin AL59(61/3.50) Cond. Set. 2

7 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country G Supply and Erection of 66kV Switch Yard Materials as per respective technical specifications and relevant special conditions suitable for One Main Bus with Twin AL59(61/3.50) conductor scheme Stringing of Flyover bus with Following Conductor for all the three phases with required Silicon Rubber Insulators, hardwares & accessories, 1 spacers provided at every 4.0 mtr. interval (Suitable for 350mm spacing)etc. complete as per relevant standards and approved drawings with Jumpers for continuous Bus Arrangement. 1.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor Rmtr Silicon Rubber Insulator string-120kn. 12 Double Tension H/W & Acc with Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Double Tension H/W & Acc without Turn Buckle suitable for Twin AL59(61/3.50) cond. & 120kN SRI. 3 Spacers suitable for Twin AL59(61/3.50) Cond. (350mm Spacing) Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to Existing Bus conductor. 12 Droppers (including required suspension string with hardware & accessories, if any) & Jumpers (including Equipment to Equipment) with 2 Following conductor as per standards and approved drawings with provision of required spacers (Suitable for 350mm spacing) at every 5.0 mtr. interval. 2.1-B Break Up of Supply Items for Erection of above work AL59(61/3.50) Conductor RMtr 360 Spacers suitable for Twin AL59(61/3.50) Cond.(350mm Spacing). 30 Fire Wedge Connectors suitable for AL59(61/3.50) Conductor to AL59(61/3.50) conductor. 30 H Supply and Laying of (6+1) X 630sq.mm 66kv Aluminium XLPE power cable with end termination kit and three phase earth link without SVL in ground as per approved drawings with providing and fixing of brick and sand layer covering the cable in any type of soil & Terminal connection, clamp & connectors, support structure arrangement for satisfactory functioning Including required terminations. Job includes excavation of all type of soils, Backfilling and necessary civil work. Rmtr. 225 I 1 2 Testing & Maintenance Equipment shall be provided as per Annexure-B as below Testing & Maintenance Equipment for GIS Gas filling and Evacuating Plant for GIS as per - DILO make (Model R002) Gas Recovery unit, DILO make (Model B057R17) with required accessories namely Pressure tank storage capacity 70Kg, Rubber Hose and packing with heat treatment set 1 set 1

8 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr 3 Dew point measurement meter- DILO Make (Model R020) set 1 4 SF6 gas leakage detector - DILO Make (Model R002) set 1 Computer set with UPS dust cover etc as per technical specifications ( for set 1 5 officer in charge) A-4 size mono laser printer as per technical specifications.( for officer In set 1 6 charge) Earth Resistance Tester Digital GE-OHM C make Model no EN /VDE 0413 or updated version with better features. Insulation Resistance Tester (Test volt upto 5kV, Range 100kohm to Tohm), Megger Make, Model-S1568 LCM Kit (Range :Total leakage current- 200µA to 9mA, Resistive leakage 1 9 current- 1µA to 9mA) Make : Doble- LCM 500(Wireless) 10 Insulation Diagnostic Analyzer, Model: IDAX300 Megger make 1 system for testing overhead lines and high voltage cables 1 to determine parameters of voltage class upto 400KV namely, Impedence(Z), line angle(φ), k-factor (k0) and mutual coupling complete with supply cord, accessories like Laptop, software etc. Make: Omicron 1] CPC Line impedance test system with CPC 100, CP CU1,CP GB1 with cables. 2] CP Sequence test card with different states. 11 Clip on meter AC/DC V/I/OHM V, 0-25A Meco/Rishabh/ Motwane 1 12 Make Motor and manual Operated Oil BDV testing Kit Megger(OTS 1 100AF)/BAUR (DTA100C) make with 0-100kV range, auto cut off feature, 13 with standard ball -cup and measuring gauge as per IS. Hydraulic Platform with Loading Capcity of 350kg. and height of 10m. 1 (Firefly Energy Ltd Make,Model-A.N.I.L)/(VANJAX Make, Model-VXLTM /11000) Emergency Power Supply Unit (Make- Aux Power- Wavelength system & solution,output voltage-220v DC) Portable hand-held PD measurement kit with all required accessories suitable for GIS- Doble make (Model DFA100) CB Analyzer with 6-Channel DCRM kit with all required accessories. 1 suitable for GIS Model: HiSAC-Ultima SCOPE make with suitable 17 Laptop 18 Tan Delta Kit- Doble Make (Model-M4100)/ Megger (Delta-4000) GPS Instrument (Trimble JUNO SA handheld GPS) Hydraulic Pallet Truck (Wont Ind Equip.-Type: W-HOPT 25). 1 EOT Crane of suitable capacity (minimum 5T safe working load) s. 1 with single hook and double girder arrangement. Contractor shall submit the capacity calculation of the crane. There shall be J provision for lifting arrangement of EOT crane for maintenance purpose. However, Contractor shall submit the capacity calculation of the crane considering erection and maintenance of largest GIS component / assembly.

9 K Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Visual Monitoring System (VMS) as per technical specification. (Alongwith local PC monitoring set up, remote end PC monitoring set up shall be in the scope of supply) Lump sum LS L Online Transformer Intelligent condition monitoring system (OTICM) as per Technical Specification Lump sum LS Ventilation system (for maintaining positive pressure) shall be provided for following building as per Technical Specifications M a) 220 & 66KV GIS Hall Lump sum LS N Fire Detection and Alarm System as per Technical Specification Lump sum LS O Dismantling of following items: 1) Equipments,Cables,MKs,Panels etc. of 132kV Dhrol Line bay 2) 132kV Bus Span.1 no. 3) 66kV Bus Spans. 1 no. 4) Transformers, Equipments,Cables,MKs,Panels etc. of 03 s. of 132/66kV Transformer bays 5) DPs,Gantry Structures,Cables,Earthmat,Fencing or any obstacle creating hurdles in proposed scope of work.

10 P Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Supply and installation of Portable and wheel/trolley mounted fire extinguishers for Control room, 220kV GIS Hall, Relay panel room of GIS Hall,Transformers,Reactors and other Strategic locations as per Technical Specification. 1) Dry chemical powder type of 9 Kg. capacity.. 6 2) Dry chemical powder type of 25 Kg. capacity.. 4 3) Dry chemical powder type of 50 Kg. capacity.. 4 4) Carbon dioxide ( CO2) gas type of capacity 6.5 Kg. capacity. 9 5) Carbon dioxide (CO2) gas type of capacity 22.5 Kg. capacity. 6 6) Mechanical Foam type of capacity 9 LT.. 4 7) Mechanical Foam type of capacity 50 LT.. 4 Q Supply and installation of Tower/Split Air Conditioner Machine at following Locations. A) 3 Ton Capacity Split AC (5 star rating and reputed make) 1) LCC Room of 220kV GIS s. 5 B) 1.5 Ton Capacity Split AC (5 star rating and reputed make) 1) Testing Lab s. 2 2) Admin. Offices s. 7 3) Reception cum Waiting Room s. 3 C) 3 Ton Capacity Tower AC (3 star rating and reputed make) 1) SCADA Control Room s. 2 2) Conference Room s. 2 R 1 2 Supply and Erection of General purpose equipments and materials as per respective technical specifications and relevant special conditions. Suitable arrangement of 11kv connections (A) from 11 KV Control room of existing Wankaner SS to one no. of 11kV/415V, 500 kva distribution transformer and (B) from separate 11 KV express feeder to another 11kV/415V, 500 kva distribution transformer Which comprises of: 1) 22 kv outdoor Isolator, 630A, STC: 25 ka 3 sec. 2) 9 KV LA with support structure, insulated conductor and DP structure with DO fuse, 22kV BPIs arrangement including Dist box suitable to dist transformer. (11KV Power Cable shall be supplied by GETCO, however Laying of cable is in the scope of bidder) Package LS Distribution Transformer 11kV/415V,500 kva with suitable Dist. Box and its fixing -mounting arrangement as per drg.. GETCO/E/2S-STD/P- 031/LTD R0,Dtd Required LT Distribution boxes with LT cable and changeover switch supply is in the scope of bidder. Set 2

11 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr DG set 250 KVA suitable for Outdoor plinth mounting with required panels 3 and accessories as per Technical Specification. Set 1 Providing major spares and Tools & Tackles as per 'Annexure-A' as 4 below te: Bidder has to quote against the following spares as applicable. Quantities against the spares shall be finalized during detailed Engineering and bidder has to supply the same. If any item not quoted against spares, but required during detailed engineering shall be supplied by the successful bidder at no extra cost to GETCO. (A) 220 kv Gas Insulated Switchgear s. 3 1 General s SF6 gas Pressure Relief Devices, 3 s. - One each used in Bay Set 1 Module,CB Module and Bus Bar Module 1.2 SF6 Pressure gauge cum switch or density monitors and pressure switch Set 1 3 s. - One each used in Bay Module,CB Module and Bus Bar Module 1.3 O Rings or Seals of original material & Size used in Single Phase GIS Module of each type (Bay Module,CB Module and Bus Bar Module) s Molecular sieve in tamper,moisture & leak proof packing. Weight of each Set 1 packing shall be equal to that to be used in GIS Module consists of 3 phase 1 bay 1.5 All types of Control Valves for SF6 gas with coupler, 3 s. - One each used in Bay Module,CB Module and Bus Bar Module Set Covers/Shields with all accessories necessary to close a compartment Set 1 in case of dismantling of any part of the Enclosure so that system can be pressurised and dielectrically tested for all 3 Phase. ( 3 phase required, one complete bay) 1.7 Locking device to keep the Dis-connectors (Isolators) and Earthing s. 3 switches in close or open position in case of removal of the driving Mechanism for one complete bay.(3 Phase) 1.8 Each type of Insulator cones which support bus bar used in single bay for Set 1 line, Transformer & Bus bar module 1.9 SF6 to air bushing Set Motor of Each type and rating used in CB,Disconnector,HSE and Earth switch used in 1-phase module 1.11 Limit switches and Aux. Switches of each type used in CB,Disconnector,HSE and Earth switch used in 1-phase module

12 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr 2.0 For GIS 220 kv Circuit Breaker Complete Circuit Breaker pole with interrupter, main circuit, enclosure s. 6 and operating mechanism 2.2 Trip coil assembly used in CB Module (3 Phase) s Closing coil assembly used in CB Module (3 Phase) Set Relays, Power contactors, push buttons, timers & MCBs etc of each type & rating provided in LCC of one bay module 3 For GIS 220 kv ISOLATORS s Complete set of single phase dis-connector including main circuit,. 1 enclosure, driving mechanism etc. 3.2 High speed/fast acting fault making grounding switch (3 nos of single. 1 phase) including main circuit, enclosure and driving mechanism etc. 3.3 Single phase Earthing switch including main circuit, enclosure, driving mechanism etc. 4.0 For GIS 220 KV CURRENT TRANSFORMER Set CTs used in one module - complete for Transformer Bay and Line Bay/Bus Coupler Bay with enclosure (Single phase requirement) 5.0 For GIS 220kV Potential Transformer Gas Insulated Complete 1-Ph PT (Single phase requirement) 6 Spares for E O T crane 6.1 Hoist Motor C.T. Motor L.T.Motor All type of Limit switches used in EOT crane Set All type of brakes used in EOT crane Set 1 (B) 66 kv Gas Insulated Switchgear 1 General 1.1 SF6 gas Pressure Relief Devices, 3 s. - One each used in Bay Module,CB Module and Bus Bar Module s SF6 Pressure gauge cum switch or density monitors and pressure switch 3 s. - One each used in Bay Module,CB Module and Bus Bar Module s O Rings or Seals of original material & Size used in GIS Module of one bay (Bay Module,CB Module and Bus Bar Module) Set 1

13 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr 1.4 Molecular sieve in tamper,moisture & leak proof packing. Weight of each Set 1 packing shall be equal to that to be used in GIS Module for 1 bay 1.5 All types of Control Valves for SF6 gas with coupler, 3 s. - One each used in Bay Module,CB Module and Bus Bar Module 1.6 Covers/Shields with all accessories necessary to close a compartment in case of dismantling of any part of the Enclosure so that system can be pressurised and dielectrically tested for one complete bay s. 3 Set Locking device to keep the Dis-connectors (Isolators) and Earthing switches in close or open position in case of removal of the driving Mechanism for one complete bay. 1.8 Each type of Insulator cones which support bus bar used for line, Transformer & Bus bar module 1.9 Motor of Each type and rating used in CB,Disconnector,HSE and Earth switch used in one complete bay 1.10 Limit switches and Aux. Switches of each type used in CB,Disconnector,HSE and Earth switch used in one complete bay Set 1 Set 1 Set 1 Set For GIS 66 kv Circuit Breaker 2.1 Complete Circuit Breaker pole with interrupter, main circuit, enclosure and operating mechanism Trip coil assembly used in CB Module s Closing coil assembly used in CB Module s Relays, Power contactors, push buttons, timers & MCBs etc of each Set 1 type & rating provided in LCC of one bay module 3 For GIS 66 kv ISOLATORS s Complete set of 3 phase dis-connector including main circuit, enclosure,. 1 driving mechanism etc.for one bay 3.2 High speed/fast acting fault making grounding switch including main. 1 circuit, enclosure and driving mechanism etc. for one complete bay. 3.3 Three phase Earthing switch including main circuit, enclosure, driving mechanism etc. 4.0 For GIS 66 KV CURRENT TRANSFORMER 4.1 CTs used in one module - complete for Transformer Bay and Line Set 1 Bay/Bus Coupler Bay with enclosure 5.0 For GIS 66kV Potential Transformer 5.1 Gas Insulated Complete 1-Ph PT. 1 (C) DG set ( portable three phase 415V 10 KVA Honda / Kirlosakar set 1 make) (D) Welding M/C: Input volt v(single/two phase), 50Hz, Insulation class A, 200 Amp. With 30 m welding cable set 1 (E) Tools & Tackles (General) 1 Earthing Rod (Highly insulated FRP telescopic Earthing/ Discharge Rod. with cable suitable for 400 & 220kV Switchyard- National Make s 18

14 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr 2 Spanner [Ring, Fixed, Box] Set 3 Fix=10x11,12x13,14x15,,16x17Ring=10x11,12x13,14x15,16x17 Tubular=12x13,14x15,16x17,18x19 Screw driver=827i,927 Nut driver= 7mm - Taparia/Gedore/Zalani Make 3 Steel Roller -Size 1" s 10 4 Aluminium Roller -Size 4" s 5 5 One/two/three Wheel pulley -Size 1" (Gadore) s 2 6 Winch Machine with Handle -05 Ton Capacity s 2 7 Hydraulic Press Machine with Dog, panther, zebra & moose dye sets-- s Ton Capacity ( Hydraulic force ent. / Techno spent ) 8 Hand drill Wolf Make 240 V Capacity :-Hole up to 31 mm, Single Phase s 1 9 Drill Machine -5/8" Dia Wolf Make Standing Drill machine having 3 Feet s 2 Pillar & suitable for making Holes up to ¾. Motor 10 Chain pulley block -5 tonne capacity (Morries) s 2 11 Wire rope pulley block -02 Tonne (Morries) Set 1 12 Tent-Standard quality water proof Tent made from H.D.P.E. Materials with 5 s of bamboos Rods and having capacity of 8 to 10 Person to stay & size 10 Ft x 10Ft Multipurpose Set 1 13 Water pump (Crompton Make) Set -5 HP with hose pipe of 30 m s 2 Crompton Make 15 Crowbar -1.5 Mtr s 5 16 Crowbar -1.0 Mtr s 5 17 Hammer with wooden handle -10Kg s 1 18 Pickaxe ( Trikam) -2 '' width with handle s 5 19 Pawda[shovel] -12 '' width with handle s 5 20 Axe (Kuhadi) with handle s 5 21 Sythe (Dharia) with handle s Tar Poline (Tad Patri) 5X5 m (HDPE), 200 GSM s 5 23 Nylon Rope -0.5" Dia -100 mtrs (Garware Make) Bundle 1 24 Nylon Rope 0.75" Dia -100 mtrs (Garware Make) Bundle 1 25 Nylon Rope -1" Dia -100 mtrs (Garware Make) Bundle 1 26 Aluminium Ladder -15 ft. Aluminium folding factory ladder (Heavy duty) Set 1 made from high tensile aluminium alloy design no 152 AFFL 15 Ft height (4.56 mtrs) specification section= 15/8 X 1.1/4 Steps= 15/8 X 1.1/4 12 Center to Center 27 Telescopic aluminium ladder(3 sections) with platform -25 ft s 1 28 Hot air blower (Wolf Make)

15 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Small Capacity =1.5m3/min, s 1 Big Capacity =2.0m3/min s 1 29 Vaccum cleaner -Eureka Forbes Make (Industrial) s 1 Safety Tools 1 Full body Harness as per technical specification s 15 2 Halmet with ISI mark of reputed make s 10 3 Hand Gloves Hand gloves of quality as per IS certification 4770 & test Pair 6 potential 7500Volt 4 Gum boot (Pair) -Size 8,9,10. -Standard make Pair for each 3 size Display Boards and others 1 Single line diagram drawn with radium paint on a board of approx size of Set x900 mm with fixing arrangement on control room wall. 2 Gas Single line diagram drawn with radium paint on a board of approx size of 1200x900 mm with fixing arrangement on wall of 220kV GIS Hall. Set 1 3 Key board with hook for different keys of each equipments/panels/cubicles with SLD drawn with color approx size 2'x2' Set 1 5 Supply of Furniture, RO Water Filter System, Water Cooler Etc. as per 'Annexure-C' as below Set 1 Supply of Furniture, RO Water Filter System, Water Cooler Etc. 1 Furniture for 400/220/66KV S/S a) Cushioned chair of Godrej make no. Ch-1018D NO 15 b) Steel rack of size 30"X36"X15" with three partitions, prepared 20 NO 2 gauges c) Providing Control Room Table modular 5X5 Panta work surface with NO 1 pedestal CPU Trolley & Key Board tray of Godrej or equivalent d) Office table with SDU & pedestal 5026 Godrej make NO 4 e) Modular workstations of Godrej make or equivalent 4X2 Panta work surface with pedestal CPU trolley & keyboard Tray or equivalent NO 2

16 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country f) Revolving chair PCH -5D02-STAR R-MID BACK NO 40 g) Wooden sofa set- 3 seated as per drawing. NO 2 g) Wooden sofa set- 2 seated as per drawing. NO 2 h) Conference table of 'Godrej' make of "Encarta conference table' of NO 1 approved design and make. FOR 25 SEAT. i) providing and fixing laminated table as per design with laminated post Sq.meter 40 formed top, drawers/shutters with facility of lock, key, board tray, wire manger, t.w. foot rest. The same shall be made with 12mm thick ply wood. All exposed edges shall be finished with 1mm thick laminated as approved. Providing and fixing t.w beading upto 25mm size. All t.w surface shall be polished with matching colour malemine polished of 3 coats. all exposed area shall be finished with laminate as per drawing j) T.W. partition 75mm thick with vinyl polished, soft board, electrical Sq.meter 10 rack way etc complete as per drawing. k)providing and fixing laminated reception table with premium black Sq.meter 1.75 granite top as per detail drg. All edges shall be mirror polished.( 5 feet x 3.5 feet) m) Providing t.w corner/central tepoy as per design with laminated top no 2 with 9mm thick bronze glass etc with malemine polish etc complete.(size 2.5 feet x 2.5 feet) 2 RO water filter system 25Ltr. Capacity Reputed make. 1 3 Water Cooler Providing & installing SHRIRAM USHA or equivalent make water cooler of 40Ltr./hr. capacity suitable to operate on 230V+10%, 50Hz. Single phase AC supply with hermetically sealed type suction cooled compressor with overload protection confirming to IS ", Sony or equivalent make flat LCD TV. 1 6 Supply and Erection of Fire stand with 4 buckets including concreting as per our drawing & Instruction of E. I. C. Set 2 7 Providing of Insulating Mat (Size2000x1000x2mm) as per Technical Specification. 200 Supply and installation of materials for Illumination system in all respect as per respective specifications and special conditions (Important te: Concealed wiring shall be considered for Indoor S Illumination)

17 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr Indoor Illumination Providing & Fixing of Energy Efficient LED type (Techhnical spec Cl I LED 3 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point,Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp, DC Plug etc all items as per Ann-4 in following rooms (with safety device ELCB) 1 i SCADA Control Room Package LS ii Lab Package LS iii Reception Package LS iv Conference Room Package LS v Admin Offices Package LS vi LCC Room Package LS vii Security Officer Cabin Package LS Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp, DC Plug etc all items as per Ann-4 in following rooms (with safety device 2 ELCB) i LV Room Package LS ii Store Room Package LS iii Ramp Slope Package LS iv Pantry Package LS v Passage (Corridor) Package LS vi Ramp Slopes Package LS vii Veranda Package LS viii WCs Package LS ix Toilets Package LS

18 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr x AHU Rooms Package LS xi Security Cabin Package LS xii Battery Room Package LS Providing & Fixing of Energy Efficient LED type (Techhnical spec Cl I LED4 Type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs., and required industrial grade point wiring as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point,Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp, DC Plug etc all items as per Ann-4 3 in following rooms (with safety device ELCB) i GIS Room Package LS Providing & Fixing of Energy Efficient LED Type (Techhnical spec Cl I LED 1 or I LED 2 type) Indoor decorative luminaries as per design calculation, with respect to required lux level & relevant tender drgs.as per technical spec. Scope also includes providing and fixing of 15/5 A plug, Portable Emergency Light, Bell, Fan, Ex- Fan, DC Point, Occupancy & Light Level Sensor with requisite MCBs and DC 100W lamp, DC Plug etc all items as per Ann-4 in following room. 4 i Store building Package LS Outdoor Illumination Providing and fixing of flood light luminaries as per design for whole switch yard area (Tender Scope only) with Energy Efficient LED type (Techhnical spec Cl I LED 5 Type) Outdoor luminaries as per design calculation, with respect to required lux level & relevant tender drgs., and required industrial grade point wiring as per technical spec.& ancillaries and suitable for mounting on structure at appropriate height as per specifications TS illuminations cl. no with necessary GI fabrication & GI bolt nuts to fix control gear box at the structure with complete internal and external wiring to J. box,dist panel/section feeder pillar etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec ).The scope includes supply and erection of all the materials 5 required for satisfactory functioning of above work. Package LS

19 6 7 8 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Providing and installation of Energy efficient LED type post top lantern for main gate and road from main gate to switchyard via control room as per design with Philips/CGL/Bajaj/GE/Oshram make & ancillaries suitable for mounting on Gate pillars and 4.5 mtr poles with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J.box,Dist panel/section feeder pillar, fixing terminal etc. with supply of required 3 c x 2.5 mm2 copper armoured cable as per spec.this also includes the supply and erection of required 4.5 mtr poles and its foundation work as per spec and earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work. Package LS Providing and fixing of street light luminaries for reamaining area (like road, near whole compound wall/fencing area etc.) of switch yard complete as per design with Philips/CGL/Bajaj/GE/Oshram or Similar make LED lamp & ancillaries suitable for mounting on 7.0 mtr swaged poles as per spec.ts illuminations cl. no (S-LED) at appropriate height with necessary GI fabrication & GI bolt nuts to fix control gear box with complete internal and external wiring to J. box,dist panel/section feeder pillar, fixing terminal etc with supply of required 3 c x 2.5 mm2 copper armoured cable (as per spec). This also includes the supply and erection of 7.0 mtr swaged pole and foundation work as per spec. and panting with two coats of primer and two priming of zinc chromate as well as earthing with main mesh. The scope includes supply and erection of all the materials required for satisfactory functioning of above work. Package LS Supply and Erection of main lighting Panel ACP-1 as per Specifications. Set comprises minimum 2 nos.of such panels qty may be more if required as per design. Scope also includes the providing and erection of cable (size as per design requirement) and 25x6 GI strip for earthing with main mesh Set 1

20 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Supply and Erection of main lighting Panel ACP-2 as per Specifications Set comprises minimum 4 nos.of such panels qty may be more if required as per design. Scope also includes the providing and erection of cable (size as per design requirement) and 25x6 GI strip for earthing with main mesh Set 1 Supply and Erection of main lighting Panel ACP-3 as per Specifications Set comprises minimum 4 nos.of such panels qty may be more if required as per design. Scope also includes the providing and erection of cable (size as per design requirement) and 25x6 GI strip for earthing with main mesh Set 1 Supply and Erection of main lighting Panel ACP-4 as per Specifications Set comprises minimum 2 nos.of such panels qty may be more if required as per design.scope also includes the providing and erection of cable (size as per design requirement) and 25x6 GI strip for earthing with main mesh Set 1 Supply and Erection of main Yard light Dist. Board as per designed capacity ratings.scope also includes providing and erection of cable (size as per design requirement) and 50x6 GI strip for earthing with main mesh s 2 Supply and Erection of Lighting Transformers as per designed capacity.scope also includes the providing and erection of 50x6 GI strip for earthing with main mesh. Please refer the drawing "General Schematic for Illumination" in the TS Illumination. Set 1 Providing of concreting in 1:2:4 mix including muffing for erection of pole & Dist boxes panels including excavation of HR/SR as per approved drawing. Package LS Providing & fixing of ' B ' Class ISI marked GI pipe of 25 mm inner diameter for cable looping, road crossing with necessary elbow / band to J. Box etc. Package LS Providing and fixing of GI clamp (25mm wide GI strip with 6 mm GI nut bolts) on structure at approx. 1 or 2 Mtr. Interval for clamping of cable. Clamp should be fix in such a way that cable can be easily mount inside it & sustain standing on structure. This also includes required other materials,accessories etc.required for complete functioning of Illumination system of whole project. Please refer the drawing "General Schematic for Illumination" in the TS Illumination. Package LS

21 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country te: The quantities of the ACP's mentioned in the schedule of requirement are based on std. requirement, which shall be finalized during detail engineering. The bidder has to assess the qty. of ACP's at the time of quoting the bid. The qty of ACP's finalized during detail engineering is binding to the bidder & no any extra payment shall be made. In all the case the decision of GETCO will be final. T U Supply and installation of materials for Earthing system in all respect as per respective specifications and special conditions (Successful bidder has to submit the complete design and BOQ for approval) Supply and Installation of earthing strips/round bars as shown below including digging of 600 mm depth and 450 mm wide trench fixing on structure as per std equipment earthing philosophy including fixing arrangement with two bolt arrangement, jointing, welding etc. complete. a) 75 x 10 mm GI strip. RMt b) 50 x 6 mm GI strip. RMt c) 40 mm dia steel rod RMt d) 40mm dia 3mtr long steel rod s. 110 Providing and installing Check pit as per drawing and instruction of Engineer In charge with provision of earth chamber. s. 6 Supply, Installation, Testing and Commissioning of maintenance free treated earth electrodes, as per attached drawing no. GETCO/E/P-021 (2 OF 2) R2 dated and Technical specifications GETCO/E/TS- Maintenance free earth pits /R1 dated s. 100 Providing BB masonry inspection chamber (man hole) incl.light type CI cover as per GETCO drawing no P021 s. 100 Design of earthgrid for switchyard using computer algorithms for modeling grounding systems as per Cl of IEEE-80. Package LS Earthing Adequacy study for whole switchyard after commisioning earthmat in all respect (Scope as per annexure-e) Package LS te: Extra earth should be removed away from the site s/s premises or refilling earthing pits if required. All required materials for this job such as Copper Bonded Earthing Steel Rods, CI cover with frame,cement,sand, Ground Enhancement Material, gravel, bricks etc. to be supplied by the contractor. Supply and Erection of Ladder Type Cable Trays and Accessories as per respective Technical Specifications and relevant special conditions.

22 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Width of tray 450mm Rmtr. 350mm Rmtr. Length: Standard length of tray is 2500mm, Height is 75mm, Thickness is 2mm (min.) te: Cross, Tees, Elbows, Coupler plates, Bends, Reducer etc. required for complete installation of Ladder Type Tray are included in the Scope. SPECIAL NOTES: Supply & Erection of any 220/132kV & 220/66kV Transformers are not in the scope of bidder, but bidder will erect the items other than the scope of transformer manufacturer and witness during the erection and testing of the same and provide all the result in as built drawings/documents. Lightning cum Lighting Masts shall be provided for GIS Buildings, Switchyard area,control room area etc. as per DSLP Calculation. These LMs shall be utilized for Illuminaton of Switchyard also. Stringing of Earth Wire with 7/3.15 GS wire with required hardwares accessories etc. complete as per standards and approved drawings shall be provided free of cost, if required. Submission of study report of Very Fast Transient Over Voltage (VFTO) shall be in the scope of bidder. Successful bidder has to depute his expert to visit site annually for the period of five years from the date of commissioning to inspect GIS for carrying out status evaluation of GIS performance.this is intended to share the operational challenges and confirming the maintenances followed by GETCO. 6 LCC of 220kV and 66kV GIS shall be front openable. LCC shall be installed in such a way that facing of front side of LCC and GIS module is same. Opposite to LCC panel, C&R panels shall be arranged exactly in line with GIS module. Sufficient maintenance space shall be kept between LCC & C&R panel. 7 Mounting channels to be grouted in flooring for GIS support shall be designed and verified by GIS OEM only. local fabrication is allowed for such fixing arrangement. Sr (II) PLCC PART 1 220kV CHI CVT with CC=4400PF (with two windings having VA burden 50 & 50 and having accuracy of 0.2 & 3P class for metering & protection core respectively. The simultaneous burden shall be 100VA at both 0.2/3P accuracy class.the terminal for metering core shall be brought out in separate sealable compartment/box. with HF terminal for PLCC purpose along with supporting structure, Clamps/Connectors. ( For providing connection from CVT HF terminal to MCD-80 the stranded (non flexible strands) PVC insulated copper cable of size 16 sq. mm shall be used.) 3 FSK Data Modem Make: ABB & Type: NSK 5 with stand alone 19" rack with power supply module with 220V DC to 48V DC converter, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency. 6. 1

23 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country Sr 4 FSK Data Modem,Make: ABB & Type: NSK 5, Programmable for both Baud Rate (50 to 2400 Baud) and VFT Channel Centre Frequency. 0 5 PLCC Exchange of Make: MATRIX, Type Eternity 10S suitable for both PLCC Dialling and Express Communication connectivity with Universal slot architecture and Hot stand by Power supply with 220V DC to 48V DC converter, switch and CPU card having configuration for 16 s. of Trunks & 16 s. of Subscribers along with Digital Key phones- 2 s. & 2 Wire telephone instruments- 8 s. of reputed make. 1 6 DAS Meters network wiring complete up to RS 485 to RS 232 Convertor of DAS PC using a) 3 core communication cable Mtr. 100 b) RS 485 to RS 232 Converter. 1 7 PC for DAS as per specification. 1 (III) Protection Part PROTECTION BOQ of 220kV Wankaner Sub Station (132kV & 66kV Existing System) Sr V 1 2 W 1 X 1 Supply, Erection, Testing and Commissioning of Protection equipments and materials as per respective technical specifications and relevant special conditions and suitable for Single Main Bus system on 132kV side Control & Relay Panels for 132KV Bays ( Control Voltage - 110V DC ) as per tech specifications with following break up 1) Control & Relay panel for line Set 1 3) Control & Relay panel for Transformer without Differential Set 2 Integration of new bays (i.e. 3 s.) with existing numerical busbar protection scheme Alstom make MiCOM P741/2 in all respect Set 1 Supply, Erection, Testing and Commissioning of Protection equipments and materials as per respective technical specifications and relevant special conditions and suitable for Single Main Bus system on 66kV side Control & Relay Panels for 66kV bays ( Control Voltage - 110V DC ) as per tech specifications with following break up. 2) Control & Relay Panel for Interconnecting bay Set 2 Supply and installation of materials/item for Power Cable and control Cable wiring including preparation of wiring schedule. Supply and Laying of 1.1 kv PVC armoured copper/aluminum control/lt power cable in trench including binding/clamping of cable with PVC locable wire tie as per requirement including supply and fixing of identification tags on both ends and at distance of every 100mtr. (te :- Aluminium cables of size 185 mm 2 & above shall be XLPE type) 1) 2c x 2.5 mm 2, armoured copper control cable Mtr ) 4cx2.5 mm 2, armoured copper control cable Mtr. 500

24 2 3 Schedule. 2 - Plant and Mandatory Spare Parts Supplied from Within the Employer s Country 4) 4c x 4 mm 2, armoured copper control cable Mtr ) 7c x 2.5 mm 2, armoured copper control cable Mtr ) 12c x 2.5 mm 2, armoured copper control cable Mtr ) 12c x 4 mm 2, armoured copper control cable Mtr ) 19c x 2.5 mm 2, armoured copper control cable Mtr ) 27c x 2.5 mm 2, armoured copper control cable Mtr ) 4 x 10 mm 2, Al. armoured LT cable Mtr ) 3.5 x 50 mm 2, Al. armoured LT cable Mtr. 300 Termination of the control cable at panel / MK box/equipment including PVC binding dressing/shaping drilling of holes in panels for glands nuts for following size. The work also includes Looping in panel and MK box with using crimping type of lugs of suitable size with ferruling with proper size of copper cable wire. The loops should be bunched with using button tape and proper shaping etc. 1) cables from 2 core to 7 core of 2.5 & 4.0 Sq.mm size ) cables above 7 core. 140 Laying of 1.1kv PVC/XLPE armored Al. LT power cable in ground by digging trench of suitable width and 450 mm depth with providing and fixing of brick and sand layer covering the cable in any type of soil and Laying of 1.1kv PVC armored copper control cable in heavy duty PVC pipe of suitable size buried in ground by digging trench of suitable width and 450 mm depth in any type of soil including supply and fixing of Pipe and identification tags at distance of every 100 Mtrs for following size 1) Control Cables upto 7 core Mtr ) Control Cables above 7 core and all LT cables Mtr. 230 Providing and fixing of 50mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CT, PT/CVT 4 etc.equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 132 kv switch yard Mtr. 50 2) 66 kv switch yard Mtr. 25 Providing and fixing of 100mm dia 'B' class GI pipes with necessary size of band and couplings for control cable protection of CB, Isolator 4a etc.equipments including fixing with structures as per instruction of Engineer-in-charge. 1) 132 kv switch yard Mtr. 50 2) 66 kv switch yard Mtr Providing and fixing bay MK as per tech spec. 3 7 Providing and fixing Yard LT ACDB as per tech spec -with 12 OG feeders. 1 8 Providing and fixing of all weather proof, cold rolled sheet steel junction box for CVT & PT, CT terminations with 30 s. of disconnecting type, 'Elmex' make CATDM 4 or equivalent type connectors and required no of fuses, links etc.as per instruction of Engineer-in-charge.. 2