Product Data Sheet Content

Transcription

1 Product Data Sheet Model 8800 Smart Vortex Flowmeter TH MODL 8800 Fully cast, all welded meter body requires no process seals and eliates sources of fugitive emissions. Non-clogging sensor design with no ports or crevices to clog and degrade performance. Superior vibration immunity with mass balanced sensing design and Adaptive Digital Signal Processing. Advanced flow simulation diagnostics has a flow signal generator built in for remote verification of electronics. ommunicates digitally using HART protocol. ontent Specifications page 3 Hazardous Locations ertifications page 9 Dimensional Drawings page 10 Ordering Information page 21 onfiguration Data Sheet page 25

2 Model 8800 Smart Vortex Flowmeter TH MODL 8800 DLIVRS... SUPRIOR PRFORMAN High-accuracy and ambient-temperature immunity improve process control Adaptive digital-signal processing provides clean output in difficult applications Sensing mechanism design imizes vibration effects ROSMOUNT RLIABILITY All-welded meter body requires no process seals and eliates sources of fugitive emissions No ports or crevices to clog and degrade performance APPLIATION FLXIBILITY Smart/HART communications eliate unnecessary trips to the field Wide rangeability eliates the need for more than one flowmeter on a process Microprocessor-based electronics reduce setup time Simultaneous analog, digital, and pulse output signals allow multiple devices to monitor and control the flow xtended temperature range allows measurement of more processes Integral or remote electronics provide mounting flexibility ommon parts reduce spares inventory TH 8800 VORTX FLOWMTR OFFRINGS... The Model 8800A is available with wafer and flanged style meter bodies for ½- through 8-inch line sizes and accepts ASM B16.5 (ANSI), DIN, or JIS flanges. Both wafer and flanged style meter bodies are available in 316L and optional Hastelloy. Alignment rings, provided with each wafer-style flowmeter, ensure that the meter body is properly centered with the adjacent piping. The Dual-Sensor Vortex Flowmeter The dual-sensor vortex flowmeter option is designed for special applications that require redundant flow measurement. This style flowmeter is constructed of two complete vortex meters: sensor, electronics, and shedder bar (see Figure 2). The two flowmeters are welded together to provide one flowmeter with two independent flow measurements. The dual-sensor vortex flowmeter is ideally suited for critical applications requiring redundancy in plant safety shutdown systems. Applications that require two flowmeters in the same process piping and have limited piping requirements are also good applications for this style flowmeter. FIGUR 2. The Dual-Sensor Vortex Flowmeter FIGUR 1. Model 8800A Remote Mount G G910 2

3 Rosemount Inc. Specifications FUNTIONAL SPIFIATIONS Service Liquid, gas, and steam applications. Fluids must be homogeneous and single-phase. Line Sizes Wafer 1 /2, 1, 1 1 /2, 2, 3, 4, 6, and 8 inches (DN 15, 25, 40, 50, 80, 100, 150, and 200) Flanged, and Dual-Sensor Style 1 /2, 1, 1 1 /2, 2, 3, 4, 6, 8, 10, and 12 inches (DN 15, 25, 40, 50, 80, 100, 150, 200, 250, and 300) Pipe Schedules Process piping Schedules 10, 40, and 80 The appropriate bore diameter of the process piping must be entered using the HART ommunicator or AMS. Meters will be shipped from the factory at the Schedule 40 default value unless otherwise specified. TABL 1. Minimum Measurable Reynolds Numbers Line Sizes (Inches / DN) 1 /2 through 4 15 through through through 300 Reynolds Number Limitations imum imum TABL 2. Minimum Measurable Velocities (Use the larger of the two values) Feet per Second Meters per Second Liquids (1) 36/ or / or 0.22 Gases 36/ or / or 2.0 The is the process fluid density at flowing conditions in lb/ft 3 for ft/s and kg/m 3 for m/s (1) The imum measurable velocity for the 10in. line size is 0.9 ft/s (.27m/s) and 1.1 ft/s (.34m/s) for the 12in. line size. TABL 3. Maximum Measurable Velocities (Use the smaller of the two values) Feet per Second Meters per Second Liquids 90,000/ or ,000/ or 7.6 Gases (1) 90,000/ or ,000/ or 76 The is the process fluid density at flowing conditions in lb/ft 3 for ft/s and kg/m 3 for m/s (1) Accuracy limitations for gas and steam for Dual-style meters (all sizes): velocity of 100 ft/s (30.5 m/s). TABL 4. Water Flow Rate Limits in Schedule 40 Pipe Line Size (Inches/ DN) Minimum and Maximum Measurable Water Flow Rates* Gallons/Minute Scalable Frequency Adjustment Value of one pulse can be set to equal desired volume in selected engineering units. Ambient Temperature Limits Operating 58 to 185 F (50 to 85 ) ubic Meters/Hour ½/ to to / to to ½/ to to / to to / to to 130 4/ to to 225 6/ to to 511 8/ to to / to to / to to 2002 *onditions: 77 F (25 ) and 14.7 psia (1.01 bar absolute) 4 to 185 F (20 to 85 ) for flowmeters with local indicator Measurable Flow Rates apable of processing signals from flow applications which meet the sizing requirements below. To detere the appropriate flowmeter size for an application, process conditions must be within the Reynolds number and velocity limitations for the desired line size provided in Table 1, Table 2, and Table 3. onsult your local sales representative to obtain a computer sizing program that describes in greater detail how to specify the correct flowmeter size for an application. The Reynolds number equation shown below combines the effects of density ( ), viscosity ( cp ), pipe inside diameter (D), and flow rate (V). Process Temperature Limits Standard 40 to 450 F (40 to 232 ) xtended 330 to 800 F (200 to 427 ) Output Signals 420 ma Digital HART Signal Superimposed on 420 ma signal Optional Scalable Pulse Output 0 to Hz; transistor switch closure with adjustable scaling via HART communications; capable of switching up to 30 V dc, 120 ma imum Analog Output Adjustment ngineering units and lower and upper range values are user-selected. Output is automatically scaled to provide 4 ma at the selected lower range value, 20 ma at the selected upper range value. No frequency input is required to adjust the range values. Storage 58 to 250 F (50 to 121 ) 50 to 185 F (46 to 85 ) for flowmeters with local indicator Pressure Limits Flange and dual-sensor style rated for ASM B16.5 (ANSI) lass 150, 300, 600, and 900, DIN PN 10, 16, 25, 40, 64, 100, and 160, and, 20K, and 40K Wafer rated for ASM B16.5 (ANSI) lass 150, 300, and 600, DIN PN 10, 16, 25, 40, 64, and 100, and, 20K, and 40K Power Supply xternal power supply required. Flowmeter operates on 10.8 to 42 V dc teral voltage (with 250-ohm imum load required for HART communications, 16.8 V dc power supply is required) Power onsumption One watt imum 3

4 Model 8800 Smart Vortex Flowmeter TABL 5. Air Flow Rate Limits at 59 F (15 ) Process Pressure 0 psig (0 bar G) 50 psig (3,45 bar G) 100 psig (6,89 bar G) 150 psig (10,3 bar G) 200 psig (13,8 bar G) 300 psig (20,7 bar G) 400 psig (27,6 bar G) 500 psig (34,5 bar G) Flow Rate Limits Minimum and Maximum Air Flow Rates for line sizes 1 /2 inch/dn 15 through 3 inch/dn 80 1 /2 Inch/DN 15 1 Inch/DN 25 1½ Inch/DN 40 2 Inch/DN 50 3 Inch/DN 80 AFM AMH AFM AMH AFM AMH AFM AMH AFM AMH TABL 6. Air Flow Rate Limits at 59 F (15 ) Process Pressure 0 psig (0 bar G) 50 psig (3,45 bar G) 100 psig (6,89 bar G) 150 psig (10,3 bar G) 200 psig (13,8 bar G) 300 psig (20,7 bar G) 400 psig (27,6 bar G) 500 psig (34,5 bar G) Flow Rate Limits Minimum and Maximum Air Flow Rates for line sizes 4 inch/dn 100 through 12 inch/dn Inch/DN Inch/DN Inch/DN Inch/DN Inch/DN 300 AFM AMH AFM AMH AFM AMH AFM AMH AFM AMH The Model 8800 measures the volumetric flow under operating conditions (i.e. the actual volume at the operating pressure and temperatureacfm or acmh), as shown above. However, gas volumes are strongly dependent on pressure and temperature. Therefore, gas quantities are typically stated in standard or normal conditions (e.g. Scfm or Ncmh). (Standard conditions are typically 59 F and 14.7 psia. Normal conditions are typically 0 and 1 bar abs.) The flow rate limits in standard conditions are found using the equations below: Standard Flow Rate = Actual Flow Rate X Density Ratio Density Ratio = Density at Actual (Operating) onditions / Density at Standard onditions 4

5 Rosemount Inc. TABL 7. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%) Process Pressure 15 psig (1,03 bar G) 25 psig (1,72 bar G) 50 psig (3,45 bar G) 100 psig (6,89 bar G) 150 psig (10,3 bar G) 200 psig (13,8 bar G) 300 psig (20,7 bar G) 400 psig (27,6 bar G) 500 psig (34,5 bar G) Flow Rate Limits (1) Assumes steam quality is 100% Minimum and Maximum Saturated Steam (1) Flow Rates for line sizes 1 /2 inch/dn 15 through 3 inch/dn 80 ½ Inch/DN 15 1 Inch/DN 25 1½ Inch/DN 40 2 Inch/DN 50 3 Inch/DN 80 lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr TABL 8. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%) Process Pressure 15 psig (1,03 bar G) 25 psig (1,72 bar G) 50 psig (3,45 bar G) 100 psig (6,89 bar G) 150 psig (10,3 bar G) 200 psig (13,8 bar G) 300 psig (20,7 bar G) 400 psig (27,6 bar G) 500 psig (34,5 bar G) Flow Rate Limits Minimum and Maximum Saturated Steam (1) Flow Rates for line sizes 4 inch/dn 100 through 12 inch/dn Inch/DN Inch/DN Inch/DN Inch/DN Inch/DN 300 lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr (1) Assumes steam quality is 100% 5

6 Model 8800 Smart Vortex Flowmeter Load (Ohms) Load Limitations Maximum loop resistance is detered by the voltage level of the external power supply, as described by: HART ommunication requires a imum loop resistance of 250 ohms. Optional LD Indicator Displays flow variable, percent of range, current output, and/or totalized flow. nclosure Rating NMA Type 4X; SA Type 4X; IP66 PRFORMAN SPIFIATIONS Accuracy Operating Region Power Supply (Volts) R = 41.7(V ps 10.8) V ps = Power Supply Voltage (Volts) R = Maximum Loop Resistance (Ohms) Includes linearity, hysteresis, and repeatability. Liquids for Reynolds Numbers over Digital and Pulse Output ±0.65% of rate Analog Output Same as pulse output plus an additional 0.025% of span Gas and Steam for Reynolds Numbers over 15,000 Digital and Pulse Output ±1.35% of rate For 1 /2-in. through 4-in. (15 mm through 100 mm) line sizes, as the Reynolds number decreases below the stated limit to 10000, the positive limit of the accuracy error band will increase to 2.1% for the pulse output. xample: +2.1% to 0.65% for liquids. Repeatability ± 0.1% of actual flow rate Stability Analog Output Same as pulse output plus an additional 0.025% of span Accuracy limitations for gas and steam: - for 1 /2- and 1-in. (DN 15 and DN 25): velocity of 220 ft/s (67.06 m/s) - for Dual-style meters (all sizes): velocity of 100 ft/s (30.5 m/s) ±0.1% of rate over one year Process Temperature ffect Automatic K-factor correction with user-entered process temperature Table 8 indicates the percent change in K-factor per 100 F (50 ) in process temperature from reference temperature of 77 F (25 ) for direct pulse, or user-entered process temperature. TABL 9. Process Temperature ffect Material < 77 F (25 ) > 77 F (25 ) < 77 F (25 ) > 77 F (25 ) Ambient Temperature ffect Digital and Pulse Outputs No effect Analog Output Percent hange in K-Factor per 100 F (50 ) (+ 0,20) (- 0,24) (+ 0,20) (- 0,20) ±0.1% of span from 40 to 185 F (40 to 85 ) Vibration ffect An output with no process flow may be detected if sufficiently high vibration is present. The meter design will imize this effect, and the factory settings for signal processing are selected to eliate these errors for most applications. If an output error at zero flow is still detected, it can be eliated by adjusting the low flow cutoff, trigger level, or low-pass filter. As the process begins to flow through the meter, most vibration effects are quickly overcome by the flow signal. At or near the imum liquid flow rate in a normal pipe mounted installation, the imum vibration should be inch (2,21 mm) double amplitude displacement or 1 g acceleration, whichever is smaller. At or near the imum gas flow rate in a normal pipe mounted installation, the imum vibration should be inch (1,09 mm) double amplitude displacement or 1 /2 g acceleration, whichever is smaller. Mounting Position ffect Meter will meet accuracy specifications when mounted in horizontal, vertical, or inclined pipelines. MI/RFI ffect Output error less than ±0.025% of span with twisted pair from MHz for radiated field strength of 10 V/m and from MHz for conducted RF of 3V (tested per N61326). Magnetic-Field Interference Output error less than ±0.025% of span at 30 A/m (rms); meets I , Section Series Mode Noise Rejection Output error less than ±0.025% of span at 1 V rms, 60 Hz; meets I , Section ommon Mode Noise Rejection Output error less than ±0.025% of span at 30 V rms, 60 Hz; meets I , Section Power Supply ffect Less than 0.005% of span per volt 6

7 Rosemount Inc. where: P f D Q gpm or lpm Q acfm or acmh Pressure Loss The approximate pressure loss from the flowmeter can be detered using the following equations: nglish Metric Pressure loss is 1.8 meter. P for the dual sensor Minimum Back Pressure (Liquids) x x Flow metering conditions that would allow cavitation, the release of vapor from a liquid, should be avoided. This flow condition can be avoided by remaining within the proper flow range of the meter and by following appropriate system design. x x = Pressure loss (psi or kpa) = Density at operating conditions (lb/ft 3 or kg/m 3 ) = Flowmeter bore diameter (in. or mm) = Actual volumetric flow rate (gal/ or l/) = Actual volumetric flow rate (ft 3 / or m 3 /hour) x x x x x x For some liquid applications, incorporation of a back pressure valve should be considered. To prevent cavitation, the imum back pressure should be: P = 2.9 P p v P = Line pressure five pipe diameters downstream of the meter (psia or kpa abs) P= Pressure loss across the meter (psi or kpa) p v = Liquid vapor pressure at operating conditions (psia or kpa abs) Pressure loss is 1.8 meter. Failure Mode Alarm P for the dual sensor If self-diagnostics detect a gross flowmeter failure, the analog signal will be driven either below 3.75 ma or above ma to alert the user. Also, high or low alarm signal is user-selectable through the fail mode alarm jumper on the electronics. NAMUR-compliant alarm limits are available through the 4 or N Option. NAMUR-compliant limits are 3.6 ma (low) or 22.5 ma (high). Saturation Output Values When the operating flow is outside the range points, the analog output continues to track the operating flow until reaching the saturation value listed below; the output does not exceed the listed saturation value regardless of the operating flow. The 420 ma Saturation Values are 3.9 ma (low) or 20.8 ma (high). The NAMUR-ompliant Saturation Values (Option 4 or N) are 3.8 ma (low) or 20.5 ma (high). Damping Adjustable between 0.2 and 255 seconds Response Time Three vortex shedding cycles or 0.2 seconds, whichever is greater, imum required to reach 63.2% of actual input with the imum damping (0.2 seconds). Turn-on Time Less than four (4) seconds plus the response time to rated accuracy from power up. Transient Protection The optional transient teral block prevents damage to the flowmeter from transients induced by lightning, welding, heavy electrical equipment, or switch gears. The transient protection electronics are located in the teral block. The transient teral block meets the following specifications: ASM B16.5 (ANSI)/I (I 587) ategories A, B 3 ka crest (8 20 s) 6 kv crest ( s) 6 kv/0.5 ka (0.5 s, 100 khz, ring wave) Security Lockout When the security lockout jumper is enabled, the electronics will not allow you to modify functions that affect flowmeter output. Output Testing urrent Source Flowmeter may be commanded to set the current to a specified value between 4 and 20 ma. Frequency Source Flowmeter may be commanded to set the frequency to a specified value between 0 and Hz. Low Flow utoff Adjustable over entire flow range. Below selected value, output is driven to 4 ma and zero pulse output frequency (in the scaled pulse mode only). Humidity Limits Operates in 095% relative humidity under noncondensing conditions (tested to I 770, Section ). Overrange apability Analog signal output continues to 105 percent of span, then remains constant with increasing flow. The digital and pulse outputs will continue to indicate flow up to the upper sensor limit of the flowmeter and a imum frequency of Hz. Flow alibration Meter bodies are flow-calibrated and assigned a unique calibration factor (K-factor) at the factory. The calibration factor is entered into the electronics, enabling interchangeability of electronics and/or meter bodies without calculations or compromise in accuracy. 7

8 Model 8800 Smart Vortex Flowmeter PHYSIAL SPIFIATIONS NA ompliance Meets the requirements of NA (National Association of orrosion ngineers) Standard MR (96) lectrical onnections 1 /2 14 NPT, PG 13.5, or M conduit threads; screw terals provided for 420 ma and pulse output connections; communicator connections permanently fixed to teral block Non-Wetted Materials Housing Low-copper aluum (NMA 4X, SA Type 4X, IP66) Paint Polyurethane over O-rings Buna-N Flanges 316/316L lap joint Process-Wetted Materials Meter Body 316L wrought stainless and F-3M cast stainless or -22 and -276 wrought Hastelloy or X2MW and W12MW cast Hastelloy Flanges 316/316L stainless steel ollars Hastelloy -22 Surface Finish of Flanges and ollars Standard: 125 to 250 inches (3.1 to 6.3 meters) Ra roughness Smooth: 63 to 125 inches (1.6 to 3.1 meters) Ra roughness Process onnections Mounts between the following flange configurations: ASM B16.5 (ANSI): lass 150, 300, 600, 900 Mounting DIN: PN 10, 16, 25, 40, 64, 100, 160 JIS: 10K, 20K, and 40K Integral (Standard) lectronics are mounted on meter body Remote (Optional) lectronics may be mounted remote from the meter body. Interconnecting coaxial cable available in nonadjustable 10, 20, and 30 ft (3,0, 6,1, and 9,1 m) lengths. onsult factory for non-standard lengths up to 75 ft (22,9 m). Remote mounting hardware includes a polyurethane painted, carbon steel pipe mount bracket with one carbon steel u-bolt. Pipe Length Requirements The vortex meter may be installed with a imum of ten straight pipe diameters (D) upstream and five straight pipe diameters (D) downstream. Rated accuracy is based on the number of pipe diameters from an upstream disturbance. An additional 0.5% shift in K-factor may be introduced between 10 D and 35 D, depending on disturbance. For more information on installation effects, see Technical Data Sheet Tagging The flowmeter will be tagged at no charge, according to customer requirements. All tags are stainless steel. The standard tag is permanently attached to the flowmeter. haracter height is 1/16-inch (1,6 mm). A wired-in tag is available on request. Flow alibration Information Flowmeter calibration and configuration information is provided with every flowmeter. For a certified copy of flow calibration data, Option Q4 must be ordered in the model number. 8

9 Rosemount Inc. Hazardous Locations ertifications Factory Mutual (FM) Approvals 5 xplosion-proof for lass I, Division 1, Groups B,, and D; Dust-ignition proof for lass II/III, Division 1, Groups, F, and G; factory sealed. I5 Intrinsically safe for use in lass I, Division 1, Groups A, B,, and D; lass II/III, Division 1, Groups, F, and G; temp. code T4 only when connected in accordance with Rosemount drawings and ; non-incendive for lass I, Division 2, Groups A, B,, and D; factory sealed. ntity Parameters: U i = 30 V I i = 300 ma P i = 1.3 W i = 0.0 F L i = 40 H K5 5 and I5 combination U i = 30 V I i = 300 ma i = 0.0 F L i = 40 H anadian Standards Association (SA) Approvals 6 I6 xplosion-proof for lass I, Division 1, Groups B,, and D; Dust-ignition proof for lass II, Division 1, Groups, F, and G; lass III, Division 1 hazardous locations; lass I, Division 2, Groups A, B,, and D; factory sealed. Intrinsically safe for lass I, Division 1, Groups A, B,, and D; Intrinsic safety approval only when connected in accordance with Rosemount drawing ; temperature code T3 (see Table 10) 6 6 and I6 combination (see Table 10) TABL 10. SA ntity Approvals NL Intrinsic Safety and Dust ertification I1 ATX Marking x II 1 GD T 70 ertification No. BAS99ATX1222 x ia II T5 (T amb = -50 to 40 ) x ia II T4 (T amb = -50 to 70 ) ntity Parameters: U i = 30 VD I (1) i = 300 ma P (1) i = 1 W i = 0.0 F L i = 40 H NL Type N ertification N1 Barrier Manufacturer/Model Any SA approved zener barrier 30 V, 330 or 28 V, 300 or 25 V, 200 or 22 V, 180 Foxboro onverters 2AI-12V-GB 2AI-13V-GB 2AS-I3I-GB 3A2-I2D-GB 3A2-I3D-GB 3AD-I3I-GB 3A4-I2D-GB 2AS-I2I-GB 3F4-I2DA Any SA approved zener barrier 30 V, 150 SA Approved for lass I, Division 1, Groups A B D NA NA NA ATX Marking x II 3 GD T70 ertification No. BAS99ATX3221 x nl II T5 (T amb = -40 to 70 ) 42 Vdc NL Flameproof ertification D ATX Marking Remote Mount: x II 2 (1) G T70 ATX Marking Integral Mount x II 1/2 G T70 KMA ertification No. 99ATX3852X x d [ia] II T6 (T amb = -50 to 70 ) Special onditions When installed particular precautions must be taken to ensure taking account with the effect of the fluid temperature, that the ambient temperature of the electrical parts of the apparatus is comprised between -50 and 70. Standards Association of Australia (SAA) (2) ertifications 7 Flameproof: x d [ia] II T6 (T amb = 40 ) x d [ia] II T4 (T amb = 70 ) lass I, Zone 1; IP66 I7 When connected in accordance with Rosemount Drawing Intrinsic Safety: x ia II T6 (T amb = 40 ) x ia II T4 (T amb = 70 ) lass I, Zone 0 ntity Parameters: U i = 30 V I (1) i = 300 ma P (1) i = 1 W i = F L i = 40 H N7 Type N: x n II T6 (T amb = 40 ) x n II T4 (T amb = 85 ) lass I, Zone 2 (1) Total for transmitter (2) Pending final approval 9

10 Model 8800 Smart Vortex Flowmeter Dimensional Drawings FIGUR 1. Flanged-Style Flowmeter Dimensional Drawings ( 1 /2- through 12-in./15 through 300 mm Line Sizes) 3.20 (81) 2.56 (65) 1.10 (28) Teral over 2.85 (72) Diameter 3.06 (78) 1.00 (25) Display Option Diameter B lectrical onnection ASM B16.5 (ANSI) ½14 NPT (2 places) 2.00 (51) 2.00 (51) Dimensions are in inches (millimeters) A A02B, 0002B02B 10

11 Rosemount Inc. TABL 11. Flanged-Style Flowmeter ( 1 /2-through 3in./15 through 80 mm Line Sizes) Noal Size Flange Rating ½ (15) lass 150 PN 16/40 /20K 1 (25) lass 150 lass 900 PN 16/40 PN 160 /20K 1 ½ (40) lass 150 lass 900 PN 16/40 PN 160 /20K 2 (50) lass 150 lass 900 PN 16/40 PN (80) lass 150 lass 900 PN 16/40 PN 160 (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. Face-to-face A (1) 6.9 (175) 7.2 (183) 6.1 (155) 6.6 (168) 6.3 (160) 7.3 (185) 7.5 (191) 8.0 (203) 9.4 (239) 6.3 (160) 7.7 (195) 7.7 (195) 6.5 (165) 7.9 (200) 8.2 (208) 8.7 (221) 9.4 (239) 10.4 (264) 6.9 (175) 8.2 (208) 8.4 (213) 7.3 (185) 8.5 (215) 9.3 (236) 9.8 (249) 10.5 (267) 8.0 (203) 9.2 (234) 10.2 (259) 7.7 (195) 8.3 (210) 9.8 (249) 9.9 (251) 10.6 (269) 11.4 (290) 12.9 (328) 8.9 (226) 10.0 (254) 10.5 (267) 11.2 (284) 7.9 (200) 9.3 (235) 11.0 (280) A-ANSI RTJ 8.0 (203) 9.4 (239) 8.7 (221) 9.2 (234) 9.4 (239) 10.4 (264) 9.8 (249) 10.4 (264) 10.7 (271) 12.9 (328) 10.4 (264) 11.2 (284) 11.5 (292) 13.0 (330) Diameter B (2) Weight (4) (3) lb (kg) 9.1 (4,1) 10.4 (4,7) 10.8 (4,9) 10.4 (4,7) 12.3 (5,6) 10.1 (4,5) 13.5 (6,1) 12.3 (5,6) 15.0 (6,8) 15.8 (7,2) 24.3 (11,0) 13.5 (6,1) 19.5 (8,8) 19.5 (8,8) 13.7 (6,2) 17.4 (7,9) 17.6 (8,0) 23.0 (10,4) 25.3 (11,5) 36.3 (16,5) 19.3 (8,8) 27.9 (12,7) 29.3 (13,3) 18.6 (8,4) 25.6 (11,6) 22.0 (10,0) 26.0 (11,8) 29.6 (13,4) 59.4 (26,9) 23.0 (10,4) 30.6 (13,9) 36.4 (16,5) 38.7 (17,6) 19.5 (8,8) 20.1 (9,1) 28.3 (12,8) 36.9 (16,7) 46.1 (20,9) 52.1 (26,6) 75.5 (34,2) 36.3 (16,5) 45.1 (20,5) 54.4 (24,7) 59.6 (27,0) 27.6 (12,5) 35.0 (15,9) 50.0 (22,7) 11

12 Model 8800 Smart Vortex Flowmeter TABL 12. Flanged-Style Flowmeter (4-through 12-in./100 through 300mm Line Sizes) (Refer to Figure 1) Noal Size Flange Rating 4 (100) lass 150 lass 900 PN 16 PN 40 PN (150) lass 150 PN 16 PN 40 8 (200) lass 150 PN 10 PN 16 PN 25 PN (250) lass 150 PN 10 PN 16 PN 25 PN (300) lass 150 PN 10 PN 16 PN 25 PN 40 Face-to-face A (1) 10.3 (262) 11.0 (279) 13.8 (351) 8.4 (213) 9.4 (239) 10.4 (264) 11.3 (287) 12.1 (307) 8.7 (220) 8.7 (220) 11.8 (300) 11.6 (295) 12.4 (315) 14.3 (363) 8.9 (226) 10.5 (267) 12.1 (307) 10.6 (270) 10.6 (270) 14.2 (360) 13.6 (345) 14.3 (363) 16.6 (422) 10.5 (266) 10.5 (266) 11.9 (302) 12.5 (318) 14.2 (361) 15.8 (401) 12.2 (310) 12.2 (310) 16.5 (420) 14.6 (371) 15.8 (401) 19.1 (485) 11.9 (302) 12.1 (307) 13.5 (343) 14.8 (376) 16.4 (417) 18.9 (480) 14.6 (371) 14.6 (371) 18.1 (460) 16.8 (427) 18.0 (457) 20.5 (521) 13.2 (335) 13.9 (353) 15.0 (381) 16.9 (429) 18.8 (478) 21.2 (538) 15.7 (399) 15.7 (399) 19.7 (500) A ANSI RTJ 11.6 (295) 12.9 (328) 13.9 (353) 12.1 (307) 13.0 (330) 14.5 (368) 14.1 (358) 15.0 (381) 16.7 (424) 15.1 (384) 16.4 (417) 19.2 (488) 17.3 (439) 18.7 (475) 20.7 (526) Diameter B (2) Weight (4) (3) lb (kg) 50.7 (23,0) 70.8 (32,1) 96.5 (43,8) (54,3) 40.1 (18,2) 49.2 (22,3) 62.1 (28,2) 78.5 (35,6) 85.8 (38,9) 37.0 (16,8) 44.9 (20,4) 75.3 (34,2) 90.0 (40,8) (58,7) (88,7) 75.6 (34,3) 95.3 (43,2) (63,0) (76,4) 79.8 (36,2) 97.7 (44,3) (79,8) (63,3) (89,0) (133,8) (49,7) (49,2) (61,8) (70,2) (97,3) (127) (49,9) (60,9) (116) (89) (129) (216) (71) (73) (90) (111) (139) (201) (79) (100) (171) (134) (187) (269) (92) (101) (121) (157) (194) (291) (102) (130) (229) (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. 12

13 Rosemount Inc. FIGUR 2. Wafer-Style Dimensional Drawings ( 1 /2-through 1 1 /2in./15 through 40 mm Line Sizes) Teral over 2.00 (51) 2.00 (51) lectrical onnection ASM B16.5 (ANSI) 1 /2-14 NPT (2 places) 3.20 (81) 2.56 (65) 1.10 (28) 2.85 (72) Diameter 3.06 (78) 1.00 (25) Display Option Diameter D Dimensions are in inches (millimeters) lectronics housing may be rotated in 90 degree increments A Diameter B D01D, TABL 13. Model 8800 Stainless Steel Wafer Noal Size Face-to-face A (1) Diameter B (2) (3) Diameter D Weight lb (kg) (4) ½ (15) 2.56 (65) 0.54 (13,7) 7.63 (194) 1.38 (35,1) 0.23 (5,9) 7.3 (3,3) 1 (25) 2.56 (65) 7.74 (197) 1.98 (50,3) 0.23 (5,9) 7.4 (3,4) 1½ (40) 2.56 (65) 8.14 (207) 0.18 (4,6) 10.0 (4,5) (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. TABL 14. Model 8800A Hastelloy Wafer Noal Size Face-to-face A (1) Diameter B (2) (3) Diameter D Weight lb (kg) (4) ½ (15) 2.44 (62) 7.63 (194) 1.38 (35,1) 0.17 (4,3) 6.8 (3,1) 1 (25) 2.44 (62) 7.74 (197) 1.98 (50,3) 0.17 (4,3) 7.6 (3,4) 1½ (40) 3.11 (79) 8.08 (205) 0.47 (11,9) 10.8 (4,9) (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. 13

14 Model 8800 Smart Vortex Flowmeter FIGUR 3. Wafer-Style Dimensional Drawings (2-through 8-in./50 through 200 mm Line Sizes) 2.00 (51) 2.00 (51) lectrical onnection ASM B16.5 (ANSI) 1 /2-14 NPT (2 places) 3.20 (81) 2.56 (65) Teral over 2.85 (72) 1.10 (28) 1.00 (25) Diameter 3.06 (78) Display Option Diameter D Dimensions are in inches (millimeters) lectronics housing may be rotated in 90 degree increments A Diameter B B01, 0002A01D TABL 15. Model 8800 Stainless Steel Wafer Noal Size Face-to-face A (1) Diameter B (2) (3) Diameter D Weight lb (kg) (4) 2 (50) 2.56 (65) 1.92 (49) 8.85 (225) 3.86 (98) 0.12 (3) 10.6 (4,8) 3 (80) 2.56 (65) 2.87 (73) 9.62 (244) 5.00 (127) 0.25 (6) 13.6 (6,2) 4 (100) 3.42 (87) 3.79 (96) (266) 6.20 (158) 0.44 (11) 21.4 (9,7) 6 (150) 4.99 (127) 5.70 (145) (273) 8.50 (216) 1.11 (28) 49.1 (22,3) 8 (200) 6.60 (168) 7.55 (192) (296) (270) 0.89 (23) 85 (38,6) (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. TABL 16. Model 8800A Hastelloy Wafer Noal Size Face-to-face A (1) Diameter B (2) (3) Diameter D Weight lb (kg) (4) 2 (50) 3.81 (97) 1.92 (49) 8.45 (215) 3.86 (98) 0.86 (22) 10.8 (4,9) 3 (80) 3.92 (100) 2.87 (73) 9.10 (231) 5.00 (127) 0.76 (19) 15.0 (6,8) 4 (100) 4.47 (114) 3.79 (96) 6.20 (158) 0.82 (21) 23.0 (10,4) 6 (150) 4.99 (127) 5.70 (145) (273) 8.50 (216) 1.11 (28) 49.1 (22,3) 8 (200) 6.60 (168) 7.55 (192) (296) (270) 0.89 (23) 85 (38,6) (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.2 lb (0,1 kg) for display option. 14

15 Rosemount Inc. FIGUR 4. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings( 1 /2-through 8-in./15 through 200 mm Line Sizes) 3.20 (81) 2.56 (65) 1.10 (28) Teral over 2.85 (72) 2.00 (51) 2.00 (51) lectrical onnection ASM B16.5 (ANSI) 1 /2-14 NPT (2 places) 3.06 (78) 1.00 (25) Display Option Dimensions are in inches (millimeters) Diameter B A A01A, 0006B01A FIGUR 5. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings(10-through 12-in./250 through 300 mm Line Sizes) lectrical onnection ASM B16.5 (ANSI) 1 /2-14 NPT (2 places) (51) (51) 3.20 (81) 2.56 (65) 1.10 (28) 2.85 (72) Teral over 3.06 (78) 1.00 (25) Display Option Dimensions are in inches (millimeters) A Diameter B _01, 8800_02 15

16 Model 8800 Smart Vortex Flowmeter TABL 17. Vortex Dual-Sensor Style Flowmeter ( 1 /2-through 3-in./15 through 80 mm Line Sizes) Noal Size Flange Rating ½ (15) lass 150 PN 16/40 /20K 1 (25) lass 150 lass 900 PN 16/40 PN 160 /20K 1 ½ (40) lass 150 lass 900 PN 16/40 PN 160 /20K 2 (50) lass 150 lass 900 PN 16/40 PN (80) lass 150 lass 900 PN 16/40 PN 160 (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) (4) Add 0.4 lb (0,2 kg) for display option. Face-to-face A (1) 12.0 (305) 12.3 (312) 11.2 (284) 11.8 (300) 11.4 (290) 12.4 (315) 15.1 (384) 15.6 (396) 16.1 (409) 17.0 (432) 13.9 (353) 15.3 (389) 15.3 (389) 14.1 (358) 15.5 (394) 11.3 (287) 11.8 (300) 12.5 (318) 13.5 (343) 10.0 (254) 11.3 (287) 11.5 (292) 10.4 (264) 11.5 (292) 13.0 (330) 13.6 (345) 14.3 (363) 16.6 (422) 11.8 (300) 12.9 (328) 13.4 (340) 14.0 (356) 11.5 (292) 12.1 (307) 13.6 (345) 14.3 (363) 15.0 (381) 15.8 (401) 17.3 (439) 13.4 (340) 14.5 (367) 14.9 (378) 15.6 (396) 12.3 (312) 15.5 (394) A ANSI RTJ 15.6 (396) 16.1 (409) 16.1 (409) 17.0 (432) 11.8 (300) 12.3 (312) 12.5 (318) 13.5 (343) 13.6 (345) 14.1 (358) 14.3 (363) 16.7 (424) 14.8 (376) 15.7 (399) 15.8 (401) 17.4 (442) Diameter B (2) (3) Weight lb (kg) (4) 16.2 (7,4) 17.4 (7,9) 17.9 (8,1) 17.2 (7,8) 19.2 (8,7) 17.1 (7,8) 20.6 (9,3) 19.8 (9,0) 22.5 (10,2) 23.3 (10,6) 31.8 (14,4) 21.0 (9,5) 27.0 (12,3) 27.0 (12,3) 22.1 (10,0) 25.8 (11,7) 27.0 (12,3) 32.4 (14,7) 34.8 (15,8) 45.7 (20,7) 28.7 (13,0) 37.4 (17,0) 38.8 (17,6) 27.9 (12,6) 34.9 (15,8) 31.9 (14,5) 35.9 (16,3) 39.5 (17,9) 69.2 (31,4) 32.9 (14,9) 40.5 (18,4) 46.2 (21,0) 48.5 (22,0) 29.1 (13,2) 29.7 (13,5) 37.9 (17,2) 50.3 (22,8) 59.5 (27,0) 65.5 (29,7) 88.9 (40,3) 49.7 (22,5) 58.5 (26,5) 67.8 (30,8) 73.0 (33,1) 41.0 (18,6) 48.4 (22,0) 63.4 (28,8) 16

17 Rosemount Inc. TABL 18. Vortex Dual-Sensor Style Flowmeter (4- through 12-in./100 through 300 mm Line Sizes) Noal Size Flange Rating 4 (100) lass 150 lass 900 PN 16 PN 40 PN (150) lass 150 PN 16 PN 40 8 (200) lass 150 PN 10 PN 16 PN 25 PN (250) lass 150 PN 10 PN 16 PN 25 PN (300) lass 150 (1) ±0.14 inch (3.6 mm) (2) ±0.03 inch (0.8 mm) (3) ±0.20 inch (5.1 mm) PN 10 PN 16 PN 25 PN 40 (4) Add 0.4 Lb (0,2 kg) for display option. Face-to-face A (1) 15.2 (386) 16.0 (406) 17.7 (450) 18.7 (475) 13.3 (338) 14.4 (366) 15.4 (391) 16.3 (414) 17.1 (434) 13.6 (345) 13.6 (345) 16.8 (427) 19.4 (493) 20.2 (513) 22.2 (564) 16.8 (427) 18.3 (465) 19.9 (505) 21.5 (546) 18.5 (470) 18.5 (470) 22.0 (559) 24.0 (610) 24.8 (630) 27.0 (686) 20.9 (531) 20.9 (531) 22.3 (566) 22.9 (582) 24.7 (627) 26.3 (668) 22.6 (574) 22.6 (574) 27.0 (686) 14.6 (371) 15.8 (401) 19.1 (485) 11.9 (302) 12.1 (307) 13.5 (343) 14.8 (376) 16.4 (417) 18.9 (480) 14.6 (371) 14.6 (371) 18.1 (460) 16.8 (427) 18.0 (457) 20.5 (521) 13.2 (335) 13.9 (353) 15.0 (381) 16.9 (429) 18.8 (478) 21.2 (538) 15.7 (399) 15.7 (399) 19.7 (500) A ANSI RTJ 15.7 (399) 16.6 (422) 17.7 (450) 18.9 (480) 19.9 (505) 20.8 (528) 22.3 (566) 24.5 (622) 25.4 (645) 27.1 (688) 15.1 (384) 16.4 (417) 19.2 (488) 17.3 (439) 18.7 (475) 20.7 (526) Diameter B (2) (3) Weight lb (kg) (4) 68.1 (30,9) 88.2 (40,0) (51,7) (62,2) 57.6 (26,1) 66.6 (30,2) 79.6 (36,1) 95.9 (43,5) (46,8) 55.4 (25,1) 63.2 (28,7) 93.7 (42,5) (57,3) (75,3) (105,2) (50,8) (59,7) (79,5) (92,9) (56,2) (64,4) (99,8) (86,2) (111,9) (156,7) (72,7) (72,1) (83,4) (93,2) (120,2) (149,9) (80,8) (91,9) (147,0) (91) (131) (218) (73) (75) (96) (113) (141) (203) (81) (102) (173) (136) (189) (271) (94) (103) (123) (159) (196) (293) (104) (132) (231) 17

18 Model 8800 Smart Vortex Flowmeter FIGUR 6. Dimensional Drawings for Remote Mount Transmitters Teral over 3.20 (81) 2.56 (65) 1.10 (28) 2.85 (72) 1.00 (25) 3.06 (78) Display Option 2.65 (68) 2.81 (71) 4.50 (114) 2.81 (71) 4.50 (114) 2.00 (51) 2.00 (51) lectrical onnection ASM B16.5 (ANSI) 1 /2-14 NPT (2 places) 1.80 (46) 4.90 (124) Dimensions are in inches (millimeters) 1 /2-14 NPT (For Remote able onduit) 5.50 (140) A04B, 0002B04B 18

19 Rosemount Inc. FIGUR 7. Dimensional Drawings for Remote Mount Wafer-Style Flowmeters ( 1 /2- through 8-in./15 through 200 mm Line Sizes) 1 /2-14 NPT (For Remote able onduit) Dimensions are in inches (millimeters) B TABL 19. Model Stainless Steel Wafer Noal Size Wafer Style ½ (15) 6.4 (163) 1 (25) 6.5 (165) 1½ (40) 6.9 (175) 2 (50) 3 (80) 8.3 (211) 4 (100) 9.2 (234) 6 (150) 9.5 (241) 8 (200) 10.4 (264) TABL 20. Model 8800A - Hastelloy Wafer Noal Size Wafer Style ½ (15) 6.3 (160) 1 (25) 6.5 (165) 1½ (40) 6.8 (173) 2 (50) 7.2 (183) 3 (80) 7.8 (198) 4 (100) 8.3 (211) 6 (150) 9.5 (241) 8 (200) 10.4 (264) 19

20 Model 8800 Smart Vortex Flowmeter FIGUR 8. Dimensional Drawings for Flanged-and Dual-Sensor Flanged-Style Remote Mount Flowmeters ( 1 /2-through 12-inch/15 through 300 mm Line Sizes) 1 /2-14 NPT (For Remote able onduit) 1 /2-14 NPT (For Remote able onduit) Flanged Flowmeter Dimensions are in inches (millimeters) Dual-Sensor Style Flowmeter B02, A TABL 21. Remote Mount, Flanged-and Dual Sensor Flowmeter Dimensions Noal Size Flange Style ½ (15) 6.4 (162) 1 (25) 6.5 (165) 1½ (40) 6.8 (173) 2 (50) 7.2 (183) 3 (80) 7.8 (198) 4 (100) 8.3 (211) 6 (150) 9.5 (241) 8 (200) 10.4 (264) 10 (250) 11.5 (292) 12 (300) 12.4 (315) 20

21 Rosemount Inc. Ordering Information Model A ode W F D Product Description Vortex Flowmeter Vortex Flowmeter, Hastelloy wafer meters only Meter Style Wafer style Flanged style Dual-sensor style (Flanged style only) ode Line Size /2 Inch (15 mm) Inch (25 mm) /2 Inches (40 mm) Inches (50 mm) Inches (80 mm) Inches (100 mm) Inches (150 mm) Inches (200 mm) Inches (250mm) Inches (300mm) ode Wetted Materials S 316L wrought stainless and F-3M cast stainless H (1) -22 and -276 wrought Hastelloy ; X2MW and W12MW cast Hastelloy ode Flange or Alignment Ring Size A1 ASM B16.5 (ANSI) RF lass 150 A3 ASM B16.5 (ANSI) RF A6 ASM B16.5 (ANSI) RF A7 (2) ASM B16.5 (ANSI) RF lass 900 B1 ASM B16.5 (ANSI) RTJ lass 150 for flange-style only B3 ASM B16.5 (ANSI) RTJ for flange-style only B6 ASM B16.5 (ANSI) RTJ for flange-style only B7 (2) ASM B16.5 (ANSI) RTJ lass 900 for flange-style only 1 ASM B16.5 (ANSI) RF lass 150, smooth finish 3 ASM B16.5 (ANSI) RF, smooth finish 6 ASM B16.5 (ANSI) RF, smooth finish 7 (2) ASM B16.5 (ANSI) RF lass 900, smooth finish D0 DIN PN Type D D1 DIN PN 16 (PN 10/16 for wafer-style)2526-type D D2 DIN PN Type D D3 DIN PN 40 (PN 25/40 for wafer-style) 2526-Type D D4 DIN 2526-Type D D6 (3) DIN 2526-Type D D7 (2) DIN PN Type D G0 DIN PN Type N for flange-style only G1 DIN PN Type N for flange-style only G2 DIN PN Type N for flange-style only G3 DIN PN Type N for flange-style only G4 DIN 2512-Type N for flange-style only G6 DIN 2512-Type N for flange-style only G7 (2) DIN PN Type N for flange-style only ontinued on Next Page 21

22 Model 8800 Smart Vortex Flowmeter ode H0 H1 H2 H3 H4 H6 (3) H7 (2) J1 J2 J4 ode N ode Flange or Alignment Ring Size DIN PN Type DIN PN 16 (PN 10/16 for wafer-style) 2526-Type DIN PN Type DIN PN 40 (PN 25/40 for wafer-style) 2526-Type DIN 2526-Type DIN 2526-Type DIN PN Type Sensor Process Temperature Range Standard: -40 to 450 F (-40 to 232 ) xtended: -330 to 800 F (-200 to 427 ) onduit ntry 1 1 /2-14 NPT 2 M PG 13.5 ode D P ode Outputs 4-20 ma digital electronics (Hart protocol) 4-20 ma digital electronics (Hart protocol) with scaled pulse alibration 1 Flow calibration ode Options Hazardous Locations ertifications 5 Factory Mutual (FM) explosion-proof approval I5 Factory Mutual (FM) intrinsic safety approval K5 Factory Mutual (FM) 5 and I5 combination approval I1 NL intrinsic safety and dust certification N1 NL Type N certification D NL flameproof certification 6 anadian Standards Association (SA) explosion-proof approval I6 anadian Standards Association (SA) intrinsic safety approval 6 anadian Standards Association (SA) 6 and I6 combination approval 7 Standards Association of Australia (SAA) flameproof certification (pending final approval) I7 Standards Association of Australia (SAA) intrinsic safety certification (pending final approval) N7 Standards Association of Australia (SAA) Type N certification (pending final approval) Other Options M5 LD indicator P2 leaning for special services 4 Analog output levels compliant with NAMUR recommendation N43, 18-January-1994 and high alarm level (4) N Analog output levels compliant with NAMUR recommendation N43, 18-January-1994 and low alarm level (4) R10 Remote electronics with 10 ft (3,0 m) cable R20 Remote electronics with 20 ft (6,1 m) cable R30 Remote electronics with 30 ft (9,1 m) cable RXX Remote electronics with customer-specified cable length (up to 75 ft (23 m) imum) (5) T1 Transient protection teral block V5 xternal ground screw assembly (6) 22

23 Rosemount Inc. Options ontinue ertification Options Q4 alibration data sheet per ISO B Q8 Material traceability certification per ISO B Q14 German TRB 801 Nr.45 certification per ISO B (7) Q69 Inspection certificate weld exaation (wafer) per ISO B (8) Q70 Inspection certificate weld exaation (flanged) per ISO B Q71 Inspection certification weld exaation (flanged) per ISO B (includes x-rays) Typical Model Number: 8800 F 020 S A1 N 1 D 1 M5 (1) 1 /2-in. (15 mm) through 4-in. (100 mm) flanged-style meters are with A1, A3, A6, 1, 3, D1, D3, D6, H1, H3, J1, J2, and J4 flange codes only. 6-in, (150mm) and 8-in. (200 mm) are only available in A1, A3, A6, D1, D3, D6, J1, J2, and J4 flange codes. 1 /2-in. (15mm)through 4-in. (100mm) with flange codes A1, A3, A6, 1, and 3; 2-in. (50 mm) through 4-in. (100mm) with flange codes D1, D3, H1, and H3 codes use lap joint flanges; all others use weld-neck flanges. (2) Only available for stainless steel flanged and dual-sensor style meters in line sizes 1-in. (25 mm) through 4-in. (100 mm). (3) D6 and H6 are not available for stainless steel 3-in. (80 mm) wafer meter style). (4) NAMUR compliant operation and the alarm latch options are pre-set at the factory and cannot be changed to standard operation in the field. (5) XX is a customer specified length in feet. (6) V5 only available with no approval or 5, I5, K5, 6, I6, and 6; it is standard with the other approvals. (7) Q14 is not available with flange codes A7, B7, 7, D7, G7, H7 and 10in.-12in. meters. (8) Q69 available for all Hastelloy wafers and stainless steel wafers in line sizes 1 /2-in. (15 mm), 6-in. (150 mm), and 8-in. (200 mm). TABL 22. DS Default onfiguration Item U.S. Unit (SI Unit) Service: liquid Flow rate: 0 to meter imum flow, GPM (AMH) Density: 62.4 lb/ft 3 Operating Temperature: Pipe ID: Service: LD onfiguration: Alarm: Security: Burst Mode: Software Tag: (1000 kg/m 3 ) 77 F (25 ) Schedule 40 line sizes liquid Alternating between % of range and flow rate High Off Off (Blank) 23

24 Model 8800 Smart Vortex Flowmeter 24

25 Rosemount Inc. onfiguration Data Sheet APPLIATION AND ONFIGURATION DATA SHT RQUIRD WITH ORDR Sold to: P.O. #: nd ustomer: Model No: 8800 SST Tag #: (21 characters imum) Software Tag #: (8 characters imum) Default onfiguration** U.S. Units Name: Date: S.I. Units Service: Liquid Gas Steam Fluid Description: Flow Rates: Maximum URV (20 ma value) (Default value is imum). Minimum LRV (4 ma value) 0 (Minimum flow to be measured not LRV) ( If you want LRV 0; enter desired value here ) Flow Rate Units: gal/s igal/s l/s AFM AMM kg/s lb/s gal/ igal/ l/ AFH AMH kg/ lb/ gal/h igal/h l/h AFD AMD kg/h lb/h gal/d igal/d l/d bbl/ MAMD kg/d lb/d ton/h bbl/h ston/h ft/s m/s ton/d bbl/d ston/d (1 bbl = 42 gal., 1 ston = 2000 lb, 1 ton = 1000 kg) If you select one of the following units, be sure to fill out the density ratio information below: NMD SFM SFH NMM NMH Density Ratio (from sizing program) Note: If no density ration is given, calculate the ratio with an assumed base pressure of psia, a base temperature of 59 F, and a base compressibility of one (1) for SFM and SFH. For NMM, NMH, and NMD, calculate with a base pressure of 1,01 bar, a base temperature of 0, and a base compressibility of one (1). Special: Special flow rate units (4 characters) / Second Minute Hour Day Special units conversion number: (1 Base Volume Unit = onversion Number, number of Special Units; ex. 1 gal = 1/31 barrels) Base volume unit: ubic ft Gallons Barrels ubic m Liters Imp. Gal Note: The Model 8800A/ measures actual volumetric flow rates. To use units not shown above, a conversion factor must be entered into the electronics through the use of special units. Use of this special conversion factor or the density value (used in mass flow units) requires that the process density remain constant. hanges in the process density will result in an inaccurate flow output. Operating Temperature F Operating Pressure Gauge Absolute Operating Density or Specific Gravity Viscosity (At operating temperature) Vapor Pressure (At operating temperature required for liquids only) Mating Pipe Schedule Sch 10 Sch 40 Sch 80 (Will default to Sch 40; Pipe I.D., dependent on line size) OR Mating Pipe I.d. inches mm Signal Options - required only if output Option ode P is selected ma and scaled pulse-digital smart electronics with HART protocol Pulse Mode: Direct Scaled (1 Pulse = unit) (e.g. 1 pulse = 1 gal or 1 pulse = 1 lb) Off OR ( Hz= unit) (e.g., 1000 Hz = 10 gal/) For Rosemount Internal Use Only Sales Order Line Item # ID # ont. Ad. Salesperson 25

26 Model 8800 Smart Vortex Flowmeter APPLIATION AND ONFIGURATION DATA SHT (Optional Information) Other Functions LD onfiguration: (Select as many as desired) Damping % of Range* Flow Rate* Output urrent Totalizer 2 seconds* Other (Value between 0.2 and 255 seconds.) Hardware Selectable: Alarm Security High* Low Off* On * Default setting if no options are selected Transmitter Information Descriptor (16 characters imum) Message (32 characters imum) Date: / / or / / : Default is date of calibration (Month/Day/Year) Month / Day / Year or Day / Month / Year HART Output Options The following output options are specifically used for special HART ommunications configurations Burst mode of HART digital process variable (Select one option below.) Primary variable in engineering units Primary variable in percent of range **By selecting Default onfiguration, Rosemount Inc. does not verify flowmeter sizing for your application. 26