F-2700 SERIES INSERTION VORTEX FLOW METER

Size: px

Start display at page:

Download "F-2700 SERIES INSERTION VORTEX FLOW METER"

Rosamund Paul
6 years ago
Views:

F-2700 SERIES INSERTION VORTEX FLOW METER APPLICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F

1 F-2700 SERIES INSERTION VORTEX FLOW METER APPLICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F (260 C) standard 750 F (400 C) optional Compressed air Industrial gases CALIBRATION MADE IN THE USA Vortex flow meters detect the frequency of alternating low pressure vortices that are formed as flow is diverted around a bluff body. These swirling low pressure zones apply lateral pressure first to one side and then to the other of sensors located downstream of the bluff body. This causes the sensors to vibrate. The frequency of this vibration is directly proportional to the flow velocity. DESCRIPTION The ONICON F-2700 Series Insertion Vortex Flow Meter is a flexible design that delivers accurate, reliable flow measurement in a wide variety of applications. The integral temperature sensor and optional integral pressure sensor allow for direct mass flow measurement in steam and compensated flow measurement in compressed air and gases. A volumetric flow version of the meter is also available for liquid flow applications. ONICON insertion style vortex meters can be installed without disrupting flow making them ideal for retrofit applications. They are also a cost effective option in larger pipes as they are priced independent of the pipe diameter. A version of the F-2700 with temperature and optional pressure compensation is available as a DC loop powered (2-wire) device with analog and pulse outputs. Optional external DC and AC powered versions of the meter are also available. These versions offer additional options for serial communications and additional analog, pulse, frequency and alarm outputs. Every ONICON flow meter is wet calibrated in a flow laboratory against standards that are directly traceable to N.I.S.T. A certificate of calibration accompanies every meter. FEATURES Mass flow measurement from a single instrument Optional steam energy flow measurement Integral 1,000 W platinum RTD for precise temperature measurement Optional integral pressure transducer for accurate pressure readings at the meter location DC loop powered operation Maintenance free non-moving parts design Wear resistant bluff body/sensor design Advanced signal processing algorithms ensure stable flow readings and reject noise. Easy-to-install meter arrives fully programmed and ready to use. Optional multi-analog output versions available. HART serial communication Optional BACnet MS/TP or MODBUS RTU RS485 serial communication GENERAL SPECIFICATIONS ACCURACY Steam and gases (Reynolds Number 10,000) Percent of reading accuracy to within: ± 1.0% for steam and gases (volumetric) ± 1.5% for steam and gases (mass) Repeatability: ± 0.2% Long term stability: ±0.2% over a period of 1 year Liquids ± 0.7% for liquids (volumetric) Repeatability: ± 0.2% Long term stability: ±0.2% over a period of 1 year Belcher Road South, Largo, FL USA Tel +1 (727) Fax +1 (727) sales@onicon.com 02-15

2 EXIT SENSING METHOD Vortex shedding with integral piezoelectric sensors Integral 1,000 W platinum RTD (optional) provides instantaneous temperature Integral pressure transducer (optional) provides instantaneous pressure. OPERATING TEMPERATURE RANGE Ambient: -40 F (-40 C) to +185 F (+85 C) Process: -330 F (-200 C) to +500 F (+260 C) Optional high temperature limit +750 F (+400 C) MAXIMUM OPERATING PRESSURE Flange rating or 1500 psi (103 bar) PRESSURE LOSS loss varies with meter size and flow rate. Please contact ONICON for detailed information. CONNECTION TYPE NPT threads with Packing Gland 2" ANSI Class 150 Flange with Packing Gland 2" ANSI Class 300 Flange with Packing Gland MATERIALS Wetted Metal Parts Electronics Enclosure: 316L Stainless Steel Epoxy painted aluminum INPUT POWER OPTIONS Loop Power: VDC, 22 ma maximum current External DC Power: VDC, 300 ma maximum current Eternal AC power: VAC 50/60 Hz, 5W. maximum power ENCLOSURE NEMA 4X (IP66) DISPLAY 2-line, 16 character alphanumeric LCD with backlighting option. Standard saturated steam display menu provides: Mass Flow Rate, Temperature, (calculated), Mass Total and Alarms (if active). Optional remote mount transmitter version available (Standard cable length 50 ft., maximum 150 ft.) OUTPUT SIGNALS PROVIDED DC loop powered version Analog Rate: 2-wire, 4-20 ma, VDC, maximum loop resistance = RL ((V supply - 12 V) /.020 A) Totalization: 2-wire open collector scaled pulse, 50 ms duration, 5-36 VDC and 40 ma / 320 mw maximum Frequency: 2-wire open drain FET, 10 khz maximum frequency, 5-36 VDC and 40 ma / 200 mw maximum Digital: HART serial communications Optional Backlight Connection: Requires external VDC power supply, 35 ma maximum current Optional DC or AC powered version Analog Rate: Up to (3) 2-wire, 4-20 ma, VDC, maximum loop resistance = RL ((V supply - 12 V) /.020 A) Totalization: (1) 2-wire open collector scaled pulse, 50ms duration, 5-36 VDC and 40 ma / 320 mw maximum Frequency: (1) 2-wire open drain FET, 10 khz maximum frequency, 5-36 VDC and 40 ma / 200 mw maximum Alarm: Up to (3) opto-coupled relay alarm outputs Digital: HART serial communications Optional on DC or AC powered version BACnet MS/TP or MODBUS RTU RS485 serial communications in place of HART Specifications subject to change without notice. REMOTE MOUNT INSTALLATION 2.1 in 3.0 in 5.0 in 8.3 in 5.7 in 3.0 in REMOTE CABLE, 50 FT STANDARD LENGTH 5.0 in 0.6 in 2.8 in REMOTE ELECTRONICS OPTION AVAILABLE ON ALL MODELS.34 in DIA. U Bolt Provided F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 2

3 EXIT STRAIGHT RUN REQUIREMENTS Insertion Vortex Flow Meter (for pipes 2 in diameter) PIPE RUN ECCENTRIC REDUCER UPSTREAM OPTIONAL FLOW STRAIGHTENER ECCENTRIC EXPANSION DOWNSTREAM PIPE RUN FLOW DIRECTION 2 DIAMETERS UPSTREAM STRAIGHT PIPE RUN TO FLOW STRAIGHTENER * MINIMUM UPSTREAM STRAIGHT PIPE RUN TO FIRST OBSTRUCTION MINIMUM DOWNSTREAM STRAIGHT PIPE RUN 5 DIAMETERS Obstruction Single bend preceded by 9 diameters of straight pipe * Upstream Straight Pipe Run Requirements Straight pipe run without flow straightener Straight pipe run to flow straightener 10 Dia NA Outflowing tee 10 Dia NA Pipe size reduction before meter 10 Dia NA Single bend preceded by 9 diameters of straight pipe 15 Dia 8 Dia Expansion before meter 20 Dia 8 Dia Multiple bends out of plane 30 Dia 13 Dia Partially open valve 30 Dia 13 Dia Control valve / P.R.V. 50 Dia 23 Dia F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 3

4 FLOW METER OPERATING RANGES Insertion Meter Flow Rates for Saturated Steam Nominal diameter in inches and Saturated Steam Flow Specific Operating s Insertion Meter Flow Rates in lb/hr Nominal Diameter (in), Schedule (psig) Density (lb/ft 3 ) lbs / hr " " " " " Flow Rates for Water Rate Water and Flow Rates (GPM) Nominal Diameter (in) Min GPM Max GPM F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 4

5 METER ORDERING INFORMATION Insertion Vortex Meter Codification = F-2700-ABC-DEFG A = Connection Type 0 = 2 Male NPT threads with retractor 1 = 2 ANSI class 150 flange with retractor 3 = 2 ANSI class 300 flange with retractor 6 = 2 ANSI class 600 flange with retractor 7 = 2 Male NPT threads without retractor ( 50psig maximum pressure) 8 = 2 ANSI class 150 flange without retractor ( 50psig maximum pressure) 9 = 2 ANSI class 300 flange without retractor ( 50psig maximum pressure) B = Integral or Remote Mount Transmitter 1 = Integral Mount 2 = Remote Mount C = Temperature / Compensation 0 = Integral temperature compensation 1 = Integral temperature & pressure sensor, 30 psia maximum 2 = Integral temperature & pressure sensor, 100 psia maximum 3 = Integral temperature & pressure sensor, 300 psia maximum 4 = Integral temperature & pressure sensor, 500 psia maximum 9 = None D = Input Power 0 = Loop powered (Only available with Output Signals option F=0) 1 = External VDC powered 2 = External VAC powered E = Output Signals 0 = 4-20mA output*, pulse output & frequency output 1 = 4-20mA output, pulse output & frequency output, alarm output & MODBUS 2 = 4-20mA output, pulse output & frequency output, alarm output & BACnet 3 = (3) 4-20mA outputs, (3) alarm outputs, (1) pulse output (1) frequency output & MODBUS 4 = (3) 4-20mA outputs, (3) alarm outputs, (1) pulse output (1) frequency output & BACnet 5 = (3) 4-20mA outputs*, (3) alarm outputs, (1) pulse output (1) frequency output 6 = 4-20mA output*, pulse output & frequency output, alarm output F = Operating Temperature 0 = 500 F 1 = 750 F G = Energy Meter 0 = None 1 = Gross energy meter 2 = Net energy meter (requires additional remote temperature sensor.) * Available with HART serial communications Remote Temperature Sensor and Thermowell Installation Kit (Required for Net Energy Meter) Part Number Description Remote Temperature Sensor, 1,000 Ohm 4-wire Class A Platinum RTD Remote Thermowell Kit for 1½" Welded Steel Pipe Remote Thermowell Kit for 2-5" Welded Steel Pipe Remote Thermowell Kit for 6-14" Welded Steel Pipe Note: Net energy meter requires 1 temperature sensor and 1 thermowell installation kit sized to pipe. F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 5

6 EXIT EXIT INSERTION METER DIMENSIONS & WEIGHTS Retractor REMOVABLE Required RETRACTOR for Applications REQUIRED Over FOR 50 APPLICATIONS PSIG OVER 50 PSIG 8.0 in ( inmm) (203 mm) 5.0 in ( inmm) (127 mm) 3.0 in 3.0 (76 inmm) (76 mm) A A transducer transducer housing housing (empty on some (empty models) on some models) * Orientation Orientation lever lever 3/4" NPT 3/4" Conduit NPT Conduit entry entry Electronics Electronics enclosure enclosure clamp clamp Packing Packing gland gland 2 inch 2 inch Male 2 inch NPT B max. 2 male inch NPT Male NPT B max. male NPT Vortex Vortex sensor sensor head head *This dimension is the same for integral and remote mount meters. 2 inch 2 Mounting inch flange Mounting flange Depth marker Depth marker arrow arrow Stanchion Stanchion Scribe mark Scribe mark Insertion tool Insertion tool Upper retractor bracket Upper retractor bracket lock bolt lock (center) bolt Sensor (center) Sensor alignment alignment pointer pointer clamp nuts clamp nuts clamp bolts clamp bolts Packing gland nuts Packing (covered gland by stem nuts clamp) (covered Lower retractor by stem clamp) Lower bracket retractor bracket housing housing Mounting Option Standard Length Extended Length in (mm) A B A B Mounting Option in (mm) Standard Length Male NPT 40.5 (1029) 21.5 (546) 52.5 A(1334) 33.5 B(851) ANSI Packing Class Gland 150 Flange & Male NPT 40.5 (1029) 21.1 (536) 52.5 (1334) 40.5 (1029) 33.1 (841) 21.5 (546) ANSI Class 300 Flange 40.5 (1029) 21.1 (536) Packing Gland & ANSI Class 150 Flange 52.5 (1334) 40.5 (1029) 33.1 (841) 21.1 (536) Packing Gland & ANSI APPROXIMATE Class 300 Flange WEIGHT, LB (KG) 40.5 (1029) 21.1 (536) SL EL APPROXIMATE WEIGHT, LB (KG) NPT 16 (7.1) 17 (7.6) SL EL Class (9.4) NPT 22 (9.9) 16 (7.1) 17 (7.6) Class (11.3) 26 (11.8) Class (9.4) 22 (9.9) Add 11 LB (5 KG) for remote electronics Class (11.3) 26 (11.8) Add 11 LB (5 KG) for remote electronics Extended Len A 52.5 (1334) (1334) (1334) 33. Sensor head Sensor head F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 6

FLOW STRAIGHTENER Gasket Thickness, Nominal Serrations show located under gasket, if provided. 0.1250 Note: Dimension C indicates ID for serrations. Dim B Dim C Dim A 1.

98 14386 PRE-CUT GASKETS Pre-cut ⅛ gaskets for use with class 300 raised face flanges. Gaskets are suitable for use with water, inert gases and saturated steam up to 150 psig.

7 FLOW STRAIGHTENER Gasket Thickness, Nominal Serrations show located under gasket, if provided Note: Dimension C indicates ID for serrations. Dim B Dim C Dim A # of holes - 35 Diameter Dim A Dim B Dim C Part # Each 2 (50mm) (80mm) (100mm) (150mm) (200mm) PRE-CUT GASKETS Pre-cut ⅛ gaskets for use with class 300 raised face flanges. Gaskets are suitable for use with water, inert gases and saturated steam up to 150 psig. For saturated steam applications above 150 psig, contact ONICON for assistance. Diameter Part # Each 2 (50mm) (80mm) (100mm) (150mm) (200mm) PRESSURE TRANSDUCER OPTIONS Full Scale Operating PSIa Overrange PSIa F-2700 Series Insertion Vortex Flow Meter Catalog Sheet Page 7

F-2700 SERIES INSERTION VORTEX FLOW METER

F-2700 SERIES INSERTION VORTEX FLOW METER CALIBRATION Every ONICON flow meter is wet calibrated in a flow laboratory against standards that are directly traceable to N.I.S.T. A certificate of calibration