Rosemount Product Data Sheet , Rev GA Catalog FIELDBUS PROTOCOL. Hazardous Locations Certifications

Transcription

1 Product Data Sheet Rosemount 3051 FIELDBUS PROTOCOL Hazardous Locations Certifications North American Certifications FM Approvals E5 Explosion-Proof for Class I, Division 1, Groups B, C, and D. Dust-Ignition-Proof for Class II, Division 1, Groups E, F, and G. Dust-Ignition-Proof for Class III, Division 1. T5 (Ta = 85 C), Factory Sealed, Enclosure Type 4X I5 Intrinsically Safe for use in Class I, Division 1, Groups A, B, C, and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 when connected per Rosemount drawing ; Non-incendive for Class I, Division 2, Groups A, B, C, and D. Temperature Code:T4 (Ta = 40 C), T3 (Ta = 85 C), Enclosure Type 4X For input parameters see control drawing Canadian Standards Association (CSA) E6 Explosion-Proof for Class I, Division 1, Groups B, C, and D. Dust-Ignition-Proof for Class II and Class III, Division 1, Groups E, F, and G. Suitable for Class I, Division 2 Groups A, B, C, and D for indoor and outdoor hazardous locations. Enclosure type 4X, factory sealed C6 Explosion-Proof and intrinsically safe approval. Intrinsically safe for Class I, Division 1, Groups A, B, C, and D when connected in accordance with Rosemount drawings Temperature Code T3C. Explosion-Proof for Class I, Division 1, Groups B, C, and D. Dust-Ignition-Proof for Class II and Class III, Division 1, Groups E, F, and G. Suitable for Class I, Division 2 Groups A, B, C, and D hazardous locations. Enclosure type 4X, factory sealed For input parameters see control drawing European Certifications I1 ATEX Intrinsic Safety and Dust Certification No.: BAS 98ATEX1355X II 1 GD EEx ia IIC T4 (T amb = 60 to +60 C) Dust Rating: T70 C (T amb 20 to 40 C) IP TABLE 7. Input Parameters U i = 30V I i = 300 ma P i = 1.3 W C i = 0 µf The device is not capable of withstanding the 500V insulation test required by Clause of EN50020:1994. This must be taken into account when installing the apparatus. IA N1 E8 ATEX FISCO Intrinsic Safety Certification No.: BAS 98ATEX1355X EEx ia IIC T4 (T amb = 60 to +60 C) IP TABLE 8. Input Parameters U i = 17.5 V I i = 380 ma P i = 5.32 W C i = 5 µf L i = 10 µh II 1 G The device is not capable of withstanding the 500V insulation test required by Clause of EN50020:1994. This must be taken into account when installing the apparatus. ATEX Type n and Dust Certification No.: BAS 98ATEX3356X II 3 GD EEx nl IIC T5 (T amb = 40 to +70 C) U i = 40 Vdc max Dust rating: T80 C (T amb = 20 to 40 C) IP66 The device is not capable of withstanding the 500V insulation test required by Clause of EN50020:1994. This must be taken into account when installing the apparatus. ATEX Flame-Proof and Dust Certification No.: KEMA 00ATEX2013X II 1/2 GD EEx d IIC T6 (T amb = 50 to 65 C) EEx d IIC T5 (T amb = 50 to 80 C) Dust rating T90 C, IP Vmax = 55 V dc This device contains a thin wall diaphragm. Installation, maintenance, and use shall take into account the environmental conditions to which the diaphragm will be subjected. The manufacturer s instructions for installation and maintenance shall be followed in detail to assure safety during its expected lifetime. 15

2 Rosemount 3051 Product Data Sheet Japanese Certifications E4 JIS Flame-Proof Ex d IIC T6 Australian Certifications I7 Certificate C15852 C15853 C15858 C15859 C15860 C15861 Description 3051C/D/1 FOUNDATION Fieldbus no meter 3051C/D/1 FOUNDATION Fieldbus with meter 3051T/G/1 FOUNDATION Fieldbus, SST, Silicon no meter 3051T/G/1 FOUNDATION Fieldbus, Hastelloy C276, Silicon no meter 3051T/G/1 FOUNDATION Fieldbus, SST, Silicon with meter 3051T/G/1 FOUNDATION Fieldbus, Hastelloy C276, Silicon with meter SAA Intrinsic Safety Certification No.: AUS Ex 1249X Ex ia IIC T4 (T amb = 60 C) IP66 When connected per Rosemount drawing TABLE 9. Input Parameters U i = 30 V I i = 300 ma P i = 1.3 W C i = 0 µf L i = 0 µh The apparatus may only be used with a passive current limited power source Intrinsic Safety application. The power source must be such that Po (Uo * Io) / 4. Modules using transient protection in the terminal assembly (T1 transient protection models) the apparatus enclosure is to be electrically bonded to the protective earth. The conductor used for the connection shall be equivalent to a copper conductor of 4 mm2 minimum cross-sectional area. E7 N7 SAA Explosion-Proof (Flame-Proof) Certification No.: AUS Ex 1347X Ex d IIC T6 (T amb = 40 C) Ex d IIC T5 (T amb = 80 C) DIP A21 T6 (T amb = 40 C) DIP A21 T5 (T amb = 80 C) IP65 It is a condition of safe use for transmitter enclosures having cable entry thread other than metric conduit thread that the equipment be utilized with an appropriate certified thread adaptor. SAA Type n (Non-sparking) Certification No.: AUS Ex 1249X Ex n IIC T4 (T amb = 70 C) Ex n IIC T5 (T amb = 40 C) IP66 Where the equipment is installed such that there is an unused conduit entry, it must be sealed with a suitable blanking plug to maintain the IP40 degree of protection. Any blanking plug used with the equipment shall be of a type which requires the use of a tool to effect its removal. Voltage source shall not exceed 60V ac or 75V dc. Combinations of Certifications Stainless steel certification tag is provided when optional approval is specified. Once a device labeled with multiple approval types is installed, it should not be reinstalled using any other approval types. Permanently mark the approval label to distinguish it from unused approval types. K5 KB KD K6 K8 K7 E5 and I5 combination K5 and C6 combination K5, C6, I1, and E8 combination C6, I1, and E8 combination E8 and I1 combination E7, I7, and N7 combination 16

3 Product Data Sheet Rosemount 3051 Dimensional Drawings 3051 Exploded View Certification Label Span and Zero Adjustments (1) (Standard) Electronics Housing Cover O-ring Terminal Block Cover Electronics Board Sensor Module Housing Rotation Set Screw (180 Maximum Housing Rotation without Further Disassembly) Coplanar Flange Drain/Vent Valve Process O-Ring Flange Adapter O-Ring Flange Alignment Screw (Not Pressure Retaining) Flange Adapters Flange Bolts 3031B08A 1) Span and Zero Adjustments are not available with fieldbus or profibus protocols. 17

4 Rosemount 3051 Product Data Sheet 3051C Coplanar Flange Dimensional Drawing (Differential Pressure Transmitter Shown) 0.75 (20) Clearance for Cover Removal 5.0 (127) 4.3 (110) 0.75 (20) Clearance for Cover Removal 1 /2 14 NPT Conduit Connection Conduit (Two Places, Connection Other (Two Sizes Places, Available) Other 4.1 (105) Certification Label PANEL MOUNTING Transmitter Circuitry Drain/Vent Valve 6.4 (163) Terminal Connections Coplanar Flange Process Connection Per IEC (54) ±0.012 in. Connection Centers 1 /2 14 NPT on Optional Flange Adapters. Adapters can be rotated to give connection centers of 2.00 (51), (54), or 2.25 (57). 6.2 (156) Housing Rotation Set Screw ¼ 18 NPT on Coplanar Flange for Pressure Connection without the Use of Flange Adapters Coplanar Flange Mounting Configurations with Optional Bracket (B4) for 2-in. Pipe or Panel Mounting 2.8 (72) 2.8 (71) 4.8 (120) 4.3 (110) 7.1 (181) 1.1 (28) 2.8 (71) 3 / /4 Bolts for Mounting to Transmitter 3.4 (85) (181) ( (209) 5 / /2 Bolts for Panel Mounting (Not Supplied) 2-inch U-Bolt for Pipe Mounting A06A, B06A PIPE MOUNTING 6.0 (152) 3.3 (83) A04H,I04A,M04A,L04A,J04A 18

5 Product Data Sheet Rosemount 3051 Traditional Flange Mounting Configurations with Optional Brackets for 2-in. Pipe or Panel Mounting Traditional Flange Panel Mounting Bracket (option B2/B8) Traditional Flange 2-in. Pipe Mounting Bracket (option B1/B7/BA) 2.7 (67) 10.1 (257) 4.2 (106) Impulse Piping 1.1 (28) 3.8 (95) 5 /16 x 7 /8 Bolts for Panel Mounting (Not Supplied) 2.81(71) PANEL MOUNTING BRACKET 6.2 (158) PIPE MOUNTING BRACKET 4.6 (116) 2.7 (67) 1.4 (33) J19D, I19C, E19C, C19A 9.6 (243) Traditional Flange (Options H2 H7) Dimensional Drawing 0.75 (20) Clearance for Cover Removal 5.0 (127) 4.3 (110) 1 /2 14 NPT Conduit Connection (Two Places Other Sizes Available) 4.1 (105) Certification Label Terminal Connections Transmitter Circuitry Housing Rotation Set Screw 7.9 (202) 1 /4 18 NPT on Traditional Flange for Pressure Connection Without the Use of Flange Adapters. Connection Per IEC (54) ±0.12 in. Connection Centers (54) 1.7 (43) 1 /2 14 NPT on Optional Flange Adapters. Adaptors Can Be Rotated to Give Connection Centers of 2.00 (51), (54), or 2.25 (57). 1.1 (28) 3.4 (87) 1.1 (28) Drain/ Vent Valve E30A, D30B 19

6 Rosemount 3051 Product Data Sheet 3051T Dimensional Drawings 5.0 (127) 4.3 (110) 1 /2 14 NPT Conduit Connection (Two Places, Other Sizes Available) 4.1 (105) Certification Label 0.75 (20) Clearance for Cover Removal 0.75 (20) Clearance for Cover Removal Transmitter Circuitry Terminal Connections 7.2 (183) Housing Rotation Set Screw TC6A, TB6A 3051T Typical Mounting Configurations with Optional Mounting Bracket Pipe Mounting Panel Mounting 2.9 (72) 4.3 (110) 5.1 (130) 2 (50) 6.2 (156) 2.8 (71) 3.5 (90) 6.3 (160) 4.8 (120) 6.9 (175) 20

7 Product Data Sheet Rosemount H Pressure Transmitter Exploded View and Dimensional Drawings Secondary Filled System Sensor Module Process Isolating Diaphragm High Side Process Flange Flange Bolts Drain/Vent Valve Low Side Process Flange HB2G 5.0 (127) 4.3 (110) 1 /2 14 NPT Conduit Connection (Two Places, Other Sizes Available) 4.1 (105) Certification Label 0.75 (19) Clearance for Cover Removal 0.75 (19) Clearance for Cover Removal Transmitter Circuitry Terminal Connections Housing Rotation Set Screw 9.0 (228) 10.8 (275) 1 /2 18 NPT on Process Flange for Pressure Connection Without the Use of Mounting Adapters Drain/Vent Valve 1.2 (30) 3.4 (86) 1.1 (28) 1 /2 14 NPT on Optional Mounting Adapters. Adapters Can Be Rotated to Give Adapter Connection Centers of 2.00 (51), (54), or 2.25 (57) i01A, H01B TA4A, TB4A, TC4A 21

8 Rosemount 3051 Product Data Sheet 3051H Mounting Brackets for 2-in. Pipe and Panel Mount (Option Code B5/B6) Impulse Piping PIPE MOUNTING CONFIGURATIO 0.7 (16) 2.7 (67) 4.4 (109) PANEL MOUNTING CONFIGURATION 7 / /4 Bolts Supplied for Attaching Bracket to Transmitter 2.7 (67) Impulse Piping G19A, F19B, 3051HB3A, HA3B 22