EG Series Installation Manual

Transcription

1 EG Series Installation Manual Convenient Micro Connectors (M) speed installation and maintenance Enclosure is fully potted and sealed to eliminate threat of moisture contamination in the wiring and electronics High Intensity red and green LED s indicate electronic switch status Approval Agency Controlled Document. No Changes Authorized Without Prior Agency Approval StoneL 67 US Highway 9 Fergus Falls, MN 67 USA Telephone: (8) Fax: Toll Free in US & Canada: sales@stonel.com Web-site:

2 Eclipse (EG) Model Number Descriptions (Example: EGC6RA) Page Function Enclosure/Approvals Entry Options Visual Indicator Brand Options EG Sensor Modules () SST N.O. Sensors () SST N.C. Sensors () NAMUR Sensors (DIN 9) Bus Communication Modules 9 DeviceNet Communication VCT Module C North American (NEC/CEC) D International (IEC/ATEX) P North American (NEC/CEC) A International (IEC/ATEX) () -pin M Male Connector () -pin M Male Connector () -pin M Female Connector () -pin M Male Connector 6 () -pin M Male Connector () -pin M Female Connector R Red Closed/Green Open G Green Closed/Red Open F Flow Line T Three Way (90 rotation) T Three Way (90 rotation) A StoneL M Metso N Neles -***** Special 9 Foundation Fieldbus VCT Module (Bus Powered Outputs) 9 Foundation Fieldbus VCT Module (VDC Externally Powered Outputs) XX Special Configuration D Red Closed/Green Open N Green Closed/Red Open L Flow Line 9 Modbus Communication VCT Module S T Three Way (90 rotation) 96 AS-i Communication VCT Module T T Three Way (90 rotation) (Standard Addressing Version) X Special 97 AS-i Communication VCT Module (Extended Addressing Version)

3 General Specifications and Ratings Operating Life Unlimited Materials of Construction (User to check the chemical compatibility of the materials used in their process to ensure chemical compatibility) Housing Lexan Polycarbonate Drum Lexan Polycarbonate Fasteners Stainless Steel Triggers & Couplings Stainless Steel Lexan is a registered trademark of General Electric Corporation. Temperature Range -0 C to 80 C (-0 F to 80 F) Enclosure Protection NEMA, X & 6; IP67 Warranty Function Module Five Years Indicator & Triggering Two Years Product Patents,6,96;,67,96 Dimensions - Inches (mm). (60). (60) 0.67 (7) 6.0 () M Micro Connectors

4 Eclipse Basic Mounting and Sensor Setting Mounting to ISO-NAMUR Style Actuators. ( Namur Size & ) Attach Function Module using fasteners provided in the mounting kit and tighten to -0 inch pounds. (Do not over tighten). ( Namur Size and Non-Namur applications ) Attach spacer or bracket to actuator with fasteners provided in the mounting kit and tighten securely. Attach Function Module to spacer or bracket and tighten to -0 inch pounds. (Do not over tighten).. Place the Drive Block into the slot of the actuator shaft. Next, place the Inner Drum over the Drive Block, ensuring the Drive Block goes into the mating recess of the Inner Drum. Now slide both Trigger Adjustment Rings over the Inner Drum (for the Flow Line option, place the yellow flow line bar on top of the Visual Indicator Trigger Assembly). Finally, insert the Drum Fastner (provided with the mounting kit) through the entire Visual Indicator/Trigger Assembly and tighten only a couple of turns into the actuator shaft as to allow the Trigger Adjustment Rings to rotate freely to perform the sensor settings. Ensure the assembly is centered. Sensor Settings. Start with the actuator in the closed position. Ensure the Drum Fastener is loose enough to allow the Trigger Adjustment Rings to rotate. Lift and rotate the lower ring until the stainless steel trigger is in front of the lower bulls-eye on the Function Module (lower trigger activates the Red LED). Rotate the actuator to the open position. Lift and rotate the upper ring until the stainless steel trigger is in front of the upper bulls-eye on the Function Module (upper trigger activates Green LED). For the Flow Line option, lift and rotate the yellow flow line bar on top of the Visual Indicator/Trigger Assembly to indicate desired flow. Securely tighten the Drum Fastener. To adjust simply loosen screw and adjust triggers and indicator to suit your application. LEDs will energize and de-energize when powered, indicating sensor status. Indicator Cover. Install the Visual Indicator Cover. The Cover Alignment Ribs on the Visual Indicator Cover are tapered and cannot be inserted vertically into the mating grooves on the Function Module. Place the Visual Indicator Cover over and as close to the Visual Indicator/Trigger Assembly as possible. When the bottom of the Visual Indicator Cover is flush with the base of the Function Module, slide the Visual Indicator horizontally until the Cover Alignment Ribs fit completely into the mating grooves on the Function Module. Tighten the Visual Indicator Cover securely to the actuator with fastners provided in the mounting kit. (-0 inch pounds. Do not over tighten). Wiring. Control and solenoid wires as connected to the Eclipse Function Module via M micro-connectors as per information located on pages thru 8. Eclipse Function Module Closed Trigger (Red LED) () Function Module Fasteners Visual Indicator Cover* Cover Alignment Ribs * Standard Flow Line Visual Indicator not provided with cover Drive Block () Cover Fasteners Drum Fastener Trigger Adjustment Rings Inner Drum Visual Indicator/Trigger Assembly Open Trigger (Green LED) Flow Line Indicator/Trigger Assembly Open Trigger (Green LED) Flow Line Bar Closed Trigger (Red LED)

5 EG Specifications & Wiring Information Configuration: Indications: EG EG Operating Voltage: Maximum Voltage Drop: Current Ratings: Max Inrush Max Continuous Minimum On Current Leakage Current SST Solid-State Sensors (EG & EG) () Solid State Sensors (Normally Open or Normally Closed) Target On Sensor = LED On Target Off Sensor = LED Off Target On Sensor = LED Off Target Off Sensor = LED On 8- VDC; - VAC 6. 0mA mA.0 VDC/VAC VDC/VAC.0m A <0.mA with DC Voltage <0.mA with AC Voltage To Bench Test a Solid State Sensor Unit: Use StoneL Light Read Tester. Or you may use a VDC or 0 VAC power supply with a series load resistor (K ohm to 6K ohm). Connect to NO and C (EG) or NC and C (EG) male pins. WARNING: FAILURE TO USE A SERIES LOAD RESISTOR WHEN BENCH TESTING WITH A POWER SUPPLY WILL RESULT IN PERMANENT DAMAGE TO THE UNIT. SST Namur Sensors (EG) Configuration: () Namur Sensors (Normally Closed) Indications: Target On Sensor = LED Off Target Off Sensor = LED On Operating Voltage: 6-9 VDC Current Ratings: Target On (LED Off) <.0mA Target Off (LED On) >.0mA Must use intrinsically safe repeater barrier. Namur Sensors conform to EN Standard See Page 9 or Page 0 for Intrinsic Safety Hazardous Location Installation Diagram To Bench Test a Namur Sensor Unit: Use StoneL Light Read Tester or a 6-9 VDC power supply across + and - male pins. No series resistor needed. Pins EG Top + Bottom + Bottom - Top - Pins EG EG Top NO Top NC Bottom NO Bottom NC Bottom Common Bottom Common Top Common Top Common Pins EG6 EG6 Top NO Top NC Bottom NO Bottom NC Solenoid - Solenoid - Solenoid + Solenoid + Top/Btm Common Top/Btm Common N/C N/C N/C Solenoid - Solenoid - Solenoid + Solenoid +

6 EG Specifications & Wiring Information DeviceNet EG Module (EG9) Communication Protocol: DeviceNet I/O: () Discrete Inputs (Sensors) () Discrete Output (Solenoid) Default Address: 6 Bit Assignment: Inputs: ( Bytes) Bit 0 = Input (Red LED; Bottom Sensor) Bit = Input (Green LED; Top Sensor) Bit = Fault Bit (Set when both Input and Input = ) Bits 8- = Not Used Outputs: ( Byte) Bit 0 = Not Used Bit = Output (Solenoid) I/O Messaging: Polling, Cyclic, Change of State Operating Voltage: VDC via DeviceNet network Baud Rates: K, 0K, 00K Output Voltage: VDC Max. Output Current: 60mA Max. Output Power: Watts To Bench Test a DeviceNet Unit: Use VDC power supply across V + (Pin ) and V - (Pin ) of male connector. No series resistor needed. To test communication, a functioning DeviceNet network is required. Pins EG9 Shield V + V- CAN_H CAN_L Pins EG96 Shield V + V- CAN_H CAN_L N/C Solenoid - Solenoid + Foundation Fieldbus EG Module (EG9) Communication Protocol: Foundation Fieldbus I/O: () Discrete Inputs (Sensors) () Discrete Output (Piezo Valve) Function Blocks: DI, DO Channel Reference Channel = DI (Green LED) Channel = DI (Red LED) Channel = DO (OUT ) Operating Voltage: 9- VDC (Foundation Fieldbus Voltage) Max Output Current: 6. VDC. Current limited to ma (Bus Powered). Suitable for StoneL Piezo Valve Indication: Red LED = Bottom Sensor Green LED = Top Sensor See Page and Page for Intrinsic Safety (FISCO) Hazardous Location information and Installation Diagram. See Page for Non-Incendive Field Wiring Apparatus Installation Drawing To Bench Test a Foundation Fieldbus Module: Use VDC power supply across FB - (Pin ) and FB + (Pin ) of male connector. No series resistor needed. To test communication, a functioning Foundation Fieldbus network is required. Pins EG9 FB - FB + N/C Pins EG9 FB - FB + N/C SIM JMPR SIM JMPR Solenoid - Solenoid + 6

7 EG Specifications & Wiring Information Modbus EG Module (EG9) Communication Protocol: Modbus I/O: () Discrete Inputs (Sensors) () Discrete Output (Solenoid) Default Address: 0 Bit Assignment: Inputs: 000= Input (Red LED; Bottom Sensor) 000 = Input (Green LED; Top Sensor) Outputs: 0000 = Not Used 0000 = Output (Solenoid ) Operating Voltage: VDC (The VDC power source should share the same ground reference as the communication line) Baud Rates: 9.6K, 9.K, 8.K Output Voltage: VDC Max. Output Current: 60mA Max. Output Power: Watts To Bench Test a Modbus Unit: Use VDC power supply across V + (Pin ) and V - (Pin ) of male connector. No series resistor needed. To test communication, a functioning DeviceNet network is required. Pins EG9 N/C V + V- BUS + BUS - Pins EG96 N/C V + V- BUS + BUS - N/C Solenoid - Solenoid + AS-Interface EG Module (EG96) Communication Protocol: AS- Interface (AS-i) Configuration: () Discrete Inputs (Sensors) () Discrete Output (Solenoid) Default Address: 00 AS-Interface ID/IO Codes: ID = F; IO = ; ID = F; ID = E Bit Assignment: Inputs: Bit = Not Used Bit = Not Used Bit = (Green LED; Top Sensor) Bit = (Red LED; Bottom Sensor) Outputs: Bit = Not Used Bit = Not Used Bit = Output (Solenoid) Bit = Not Used Operating Voltage: -0 VDC (AS-i Voltage) Output Voltage: VDC Max. Output Current: 60mA Max. Output Power: Watts See Page for Non-Incendive Field Wiring Apparatus Installation Drawing To Bench Test AS-i Module: Use VDC power supply across AS-I + (Pin ) and AS-I - (Pin ) of male connector. No series resistor needed. To test communication, a functioning AS-i network is required. Pins EG96 AS-I + AS-I - Pins EG96 AS-I + AS-I - N/C Solenoid - Solenoid + 7

8 EG Specifications & Wiring Information AS-Interface EG Module (EG97) Communication Protocol: AS- Interface (AS-i) Configuration: () Discrete Inputs (Sensors) () Discrete Output (Solenoid) Default Address: 0A AS-Interface ID/IO Codes: ID = A; IO = ; ID = 7; ID = E Bit Assignment: Inputs: Bit = Not Used Bit = Not Used Bit = (Green LED; Top Sensor) Bit = (Red LED; Bottom Sensor) Outputs: Bit = Not Used Bit = Not Used Bit = Output (Solenoid) Bit = Not Used Operating Voltage: -0 VDC (AS-i Voltage) Output Voltage: VDC Max. Output Current: 00mA Max. Output Power:. Watts See Page for Non-Incendive Field Wiring Apparatus Installation Drawing To Bench Test AS-i Module: Use VDC power supply across AS-I + (Pin ) and AS-I - (Pin ) of male connector. No series resistor needed. To test communication, a functioning AS-i network is required. Pins EG97 AS-I + AS-I - Pins EG97 AS-I + AS-I - N/C Solenoid - Solenoid + 8

9 Installation Diagram for Explosive Atmospheres for Europe EGD or A models approved for Intrinsically Safe Installations: (Ex ia IIC T) EGD or A * *Note: Any Visual Indicator/Trigger Assembly option is approved HAZARDOUS (CLASSIFIED) Ex ia IIC T Intrinsic Safety Barriers (Associated Apparatus) NON-HAZARDOUS (SAFE AREA) Individual Sensor wiring Control Equipment Bottom Sensor Barrier Top Sensor Barrier 6 Shields 7 Intrinsically Safe Ground 8 9 EG Enclosure EG Pin Identifiers Pins EG Top Sensor + Bottom Sensor + Bottom Sensor - Top Sensor - INSTALLATION NOTES Intrinsically Safe Installations: (Ex ia IIC T): EG Entity Parameters: Ui = Vdc; Ii = 0 ma ; Ci = 98 nf; Li =.6 mh; Pi =.0 W The Entity Concept allows interconnection of intrinsically safe apparatus with associated apparatus when the following is true: Ui >Uo; Ii > Io; Pi > Po; Co > Ci + Ccable, Lo > Li + Lcable.. For Installations in Europe, control room equipment connected to intrinsically safe associated apparatus shall not use or generate more than the marked Um of the associated apparatus.. Installation in Europe shall be in accordance with latest editions of the wiring practices for the country of origin.. For Installations in Europe, the Associated Apparatus must be ATEX approved. Associated apparatus manufacturer's installation drawing must be followed when installing this equipment.. To maintain intrinsic safety, wiring associated with each sensor or solenoid coil wiring must be run in separate cables or separate shields connected to intrinsically safe (associated apparatus) ground. Each Sensor and Solenoid coil shall be wired as separate intrinsically safe circuits. 6. Conduit Grounding - Upon installation verify electrical continuity between conduit and ground terminal. 7. Resistance between Intrinsic Safe Ground and earth ground must be less than.0 ohm. WARNING: 8. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in location where it may be subjected to external conditions (such as high-pressure steam) which might cause a build-up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should only be done with a damp cloth. 9. Substitution of components may impair hazardous location safety. 0. No revision to drawing without prior FM Approval. 9

10 Intrinsic Safety Hazardous Location Installation Diagram EGC or P models approved for Intrinsically Safe Installations: IS Class I,II and III; Division, Groups A,B,C,D,E,F,G EGC or P * *Note: Any Visual Indicator/Trigger Assembly option is approved HAZARDOUS (CLASSIFIED) S Cl I,II,III; Div, Groups A,B,C,D,E,F,G Intrinsic Safety Barriers (Associated Apparatus) NON-HAZARDOUS (SAFE AREA) Individual Sensor wiring Control Equipment Bottom Sensor Barrier Top Sensor Barrier 6 Shields 7 Intrinsically Safe Ground 8 EG Enclosure EG Pin Identifiers Pins EG Top Sensor + Bottom Sensor + Bottom Sensor - Top Sensor - INSTALLATION NOTES: EG Entity Parameters: Ui (Vmax) = Vdc; Ii (Imax) = 0 ma ; Ci = 98 nf; Li =.6 mh; Pi =.0 W Uo < Ui (Vmax); Io < Ii (Imax); Ca > Ci + Ccable, La > Li + Lcable.. Control equipment connected to barrier must not use or generate more than 0 Vrms or Vdc.. Installation should be in accordance with ANSI/ISA RPA.6.0 "Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations" and the National Electrical Code (ANSI/NFPA 70) or in accordance with the Canadian Electric Code.. Associated apparatus manufacturer's installation drawing must be followed when installing this equipment.. To maintain intrinsic safety, wiring associated with each sensor or solenoid coil wiring must be run in separate cables or separate shields connected to intrinsically safe (associated apparatus) ground. Each Sensor and Solenoid coil shall be wired as separate intrinsically safe circuits. 6. Shield Grounding - Upon installation verify electrical continuity between shield and ground terminal. 7. Resistance between Intrinsic Safe Ground and earth ground must be less than one ohm. WARNING: 8. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in location where it may be subjected to external conditions (such as high-pressure steam) which might cause a build-up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should only be done with a damp cloth. 9. Substitution of components may impair hazardous location safety. 0

11 Intrinsic Safety (FISCO) Hazardous Location Installation Diagram FISCO Concept The FISCO Concept allows the interconnection of intrinsically safe apparatus to associated apparatus not specifically examined in such combination. The criterion for such interconnection is that voltage (Vmax), the current (Imax), and the power (Pi), which intrinsically safe apparatus can receive and remain intrinsically safe, considering faults, must be equal to or greater than the voltage (Uo, Voc, Vt), the current (Io, Isc, It), and the power (Po) which can be provided by the associated apparatus (supply unit). In addition, the maximum unprotected residual capacitance (Ci) and inductance (Li) of each apparatus (other than the terminators) connected to the Fieldbus must be less than or equal to nf and 0µH respectively. In each I.S. Fieldbus segment only one active source, normally the associated apparatus, is allowed to provide the necessary power for the Fieldbus system. The allowed voltage (Uo, Voc, Vt) of the associated apparatus used to supply the bus must be limited to the range of V d.c. to V d.c. All other equipment connected to the bus cable has to be passive, meaning that the apparatus is not allowed to provide energy to the system, except to a leakage current of 0µA for each connected device. Separately powered equipment needs a galvanic isolation to insure that the intrinsically safe Fieldbus circuit remains passive. The cable used to interconnect the devices must comply with the following parameters: Loop resistance R : - 0 ohm/km Inductance per unit length L : 0. - mh/km Capacitance per unit length C : 80-00nF/KM C = C line to line + ½ C line to shield, if both lines are floating with respect to shield or C = C line to line + C line to shield, if one line is connected to shield Trunk Length: < 000 meters Spur Length: < 0 meters Splice Length: < meters FM Approved line terminators must be used on each end of the trunk cable that have the following parameters: R = ohms C = µf (See Page for Installation Diagram and Notes)

12 Intrinsic Safety (FISCO) Hazardous Location Installation Diagram EG9C or P * models approved for Intrinsically Safe (FISCO) Installations: IS Class I,II and III; Division, Groups A,B,C,D,E,F,G *Note: All Entry options and Visual Indicator/Trigger Assembly options are approved HAZARDOUS (CLASSIFIED) IS (FISCO) Cl I,II,III Div, Groups A,B,C,D,E,F,G NON-HAZARDOUS (SAFE AREA) EG9 Enclosure FM/CSA Approved Control Equipment FM/CSA Approved Termination FM/CSA Approved Fieldbus Device n suitable for FISCO FM/CSA Approved Fieldbus Device suitable for FISCO FB + FB - Quick Connector Pin-out located below Pins EG9 FB - FB + N/C Pins EG9 FB - FB + N/C SIM JMPR SIM JMPR Solenoid - Solenoid + INSTALLATION NOTES: EG9 Entity Parameters (FISCO): Ui (Vmax)=0 Vdc; Ii (Imax)=80 ma; Ci 0.0 nf; Li=0.0 mh; Pi=. W. Installation shall be in accordance with ANSI/ISA RPA.6.0, ANSI/NFPA 70, and the National Electrical Code or in accordance with the Canadian Electric Code.. Control equipment must be FM or CSA Approved Associated Apparatus suitable for FISCO.. Control equipment connected to FISCO barrier must not use or generate more than 0Vrms or Vdc.. Resistance between FISCO Intrinsically Safe Ground and earth ground must be less than.0 Ohm. WARNING:. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in location where it may be subjected to external conditions (such as high-pressure steam) which might cause a build-up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should only be done with a damp cloth. 6. Substitution of components may impair hazardous location safety. 7. Approval Agency controlled Installation Diagram. No revision to diagram allowed without prior Factory Mutual or Approval Agency authority.

13 Non-Incendive Field Wiring Apparatus Installation Drawing EG9C or P * models approved for Non-Incendive Field Wiring Apparatus: NI Class I,II and III; Division, Groups A,B,C,D,F,G *Note: All Entry options and Visual Indicator/Trigger Assembly options are approved HAZARDOUS (CLASSIFIED) Nonincendive Field Wiring Apparatus NI; Cl I,II,III Div Groups A,B,C,D,F,G NON-HAZARDOUS (SAFE AREA) EG9 Enclosure Power Limiting Associated Apparatus Control Equipment Solenoid Connector Bus Connector FB + FB - Quick Connector Pin-out located below Pins EG9 FB - FB + N/C Pins EG9 FB - FB + N/C SIM JMPR SIM JMPR Solenoid - Solenoid + INSTALLATION NOTES: Entity Parameters: EG9 : Ui = 0 Vdc; Ii = 80 ma ; Ci = 0.0 nf; Li = 0.0 mh; Pi =. W. Installation shall be in accordance with ANSI/ISA RPA.6.0, ANSI/NFPA 70, and the National Electrical Code.. Control equipment must be FM approved to supply power in Class I, Division Areas.. Power Limiting Associated Apparatus must satisfy the conditions: Voc or Vt < Ui, Isc or It < Ii, Ca > Ci + Ccable, La > Li + Lcable of the EG9 Entity Parameters. Manufacturer's associated non-incendive field wiring apparatus installation drawing must be followed when installing this equipment.. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in location where it may be subjected to external conditions (such as high-pressure steam) which might cause a build-up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should only be done with a damp cloth. 6. Substitution of components may impair hazardous location safety.

14 Non-Incendive Field Wiring Apparatus Installation Drawing EG96C or P_* and EG97C or P_*models approved for Non-Incendive Field Wiring Apparatus: NI Class I,II and III; Division, Groups A,B,C,D,F,G *Note: All Entry options and Visual Indicator/Trigger Assembly options are approved HAZARDOUS (CLASSIFIED) Nonincendive Field Wiring Apparatus NI; Cl I,II,III Div Groups A,B,C,D,F,G NON-HAZARDOUS (SAFE AREA) EG96 or EG97 Enclosure Power Limiting Associated Apparatus Control Equipment Solenoid Connector Bus Connector ASI + ASI - Quick Connector Pin-out located below Pins EG96 and EG97 AS-I + AS-I - Pins EG96 and EG97 AS-I + AS-I - N/C Solenoid - Solenoid + INSTALLATION NOTES: Entity Parameters: EG96 or EG97 : Ui = 7 Vdc; Ii = 0 ma ; Ci = 0.0 nf; Li = 0.0 mh; Pi =.0 W. Installation shall be in accordance with ANSI/ISA RPA.6.0, ANSI/NFPA 70, and the National Electrical Code.. Control equipment must be FM approved to supply power in Class I, Division Areas.. Power Limiting Associated Apparatus must satisfy the conditions: Voc or Vt < Ui, Isc or It < Ii, Ca > Ci + Ccable, La > Li + Lcable of the EG96 or EG97 Entity Parameters. Manufacturer's associated non-incendive field wiring apparatus installation drawing must be followed when installing this equipment.. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in location where it may be subjected to external conditions (such as high-pressure steam) which might cause a build-up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should only be done with a damp cloth. 6. Substitution of components may impair hazardous location safety.

15 INSTALLATION ADDENDUM EN and EG series SPECIFIC CONDITIONS OF USE / MARKING For EN and EG Series FM08ATEX00X Specific Conditions of Use - Notes. Parts of the enclosure are non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in a location where it may be subjected to external conditions which might cause a build up of electrostatic charge on non-conducting surfaces. Additionally, cleaning of the equipment should be done only with a damp cloth. For EN and EG Series FM7US09X Specific Conditions of Use - Notes. Part of the enclosure is constructed from plastic. To prevent the risk of electrostatic sparking the plastic surface should only be cleaned with a damp cloth. Marking ATEX II G Ex ia IIC T Ga Ta = -0 C to +80 C Marking *NI / I / / ABCD - 09 *S / II / / FG *IS / I, II, III / / ADBCDEFG - 09 *See Approval Certificates for applicable models / type codes. Materials - Enclosure: Polycarbonate - Seal: Buna-N or RTV0 Attention: Replace only with identical factory parts/components. Deviation from the installation conditions in the Installation Manual and this addendum may invalidate this product's conformity with the Explosive Atmospheres, Pressure Equipment, and EMC Directives. Conformity of this product with any other "CE Mark" Directive(s) shall not be assumed. Contact StoneL for help with replacements or emergency maintenance. For installation manuals in a community language other than English, please contact StoneL. DECLARATION OF CONFORMITY Manufacturer: StoneL 67 US Highway 9 Fergus Falls, Minnesota 67 USA Products: Eclipse EN Series Valve Position Monitors and Valve Communication Terminals Eclipse EG Series Valve Position Monitors and Valve Communication Terminals Model - Type Certificates / Directives / Standards Marking EN and EG Series EN and EG Series EU Type Examination Certificate FM08ATEX00X ATEX 0//EU EN :0+A:0, EN :0 EMC 0/0/EU EN :007/A:0 EMC 0/0/EU EN :007/A:0 ATEX II G Ex ia IIC T Ga ATEX Notified Bodies for EU Type Examination Certificates: FM Approvals Ltd. Windsor, Berkshire, UK (Notified Body Number 7) Quality Assurance Certificates: ISO 900:008...TUV SUD America Inc. QAN FM06ATEXQ00.FM Approvals (Notified Body Number 7) QAR GB/FME/QAR.000..FM Approvals (Notified Body Number 7) We declare under our sole responsibility that the products, as described, are in conformity with the listed standards and directives. Fergus Falls, st August 07 Bryan Beckman, Quality Manager Authorized Person of the Manufacturer 0revE