The Annubar Flowmeter Series. Rosemount 3051SFA ProBar Flowmeter. Product Data Sheet , Rev EA Catalog

Transcription

1 , Rev EA Rosemount 3051SFA ProBar Flowmeter SPECIFICATIONS Performance System Reference Accuracy Percentage (%) of volumetric flow rate Classic Ultra Ultra for Flow (8:1 flow turndown) (8:1 flow turndown) (10:1 flow turndown) ±1.10% ±0.90% ±0.80% Repeatability ±0.1% Line Sizes Sensor Size 1: 2-in. to 8-in. (50 to 200 mm) Sensor Size 2: 6-in. to 96-in. (150 to 200 mm) Sensor Size 3: 12-in. to 96-in. (300 to 200 mm) NOTE Some mounting types are not available in larger line sizes. TABLE 1. Reynolds Number and Probe Width Sensor Size Output Minimum Rod Reynolds Number (R d ) Probe Width ( d ) in. (1.99 mm) in. (26.92 mm) in. (9.15 mm) d V p R d = Where d = Probe width (feet) V = Velocity of fluid (ft/sec) p = Density of fluid (lb m /ft 3 ) = Viscosity of the fluid (lb m /ft-sec) HART 20 ma ADC, flow rate output. Digital HART protocol superimposed on 20 ma signal, available to any host that conforms to the HART protocol. FOUNDATION Fieldbus (output code F) 17.5 ma for all configurations (including LCD display option) Performance Statement Assumptions Measured pipe I.D Electronics are trimmed for optimum flow accuracy Sizing Contact an Emerson Process Management representative for assistance. A Configuration Data Sheet is required prior to order for application verification. Annubar Sensor Surface Finish The front surface of the Annubar primary is textured for high Reynolds number applications (typically gas and steam). The surface texture creates a more turbulent boundary layer on the front surface of the sensor. The increased turbulence produces a more predictable and repeatable separation of flow at the edge of the sensor. The appropriate surface finish will be determined for each application by the Emerson Process Management sizing program. Functional Service Liquid Gas Steam 20 ma/hart Zero and Span Adjustment Zero and span values can be set anywhere within the range. Span must be greater than or equal to the minimum span. Output Two-wire 20 ma is user-selectable for linear or square root output. Digital process variable superimposed on 20 ma signal, available to any host that conforms to the HART protocol. Power Supply External power supply required. Standard transmitter ( 20 ma): 10.5 to 2. V dc with no load 3051S SIS Safety transmitter: 12 to 2 Vdc with no load 3051S HART Diagnostics transmitter: 12 to 2 Vdc with no load

2 , Rev EA The Annubar Flowmeter Series Load Limitations Maximum loop resistance is determined by the voltage level of the external power supply, as described by: Standard Transmitter Maximum Loop Resistance = 3.5 * (Power Supply Voltage 10.5) Load (Ohms) Operating Region Voltage (V dc) 2. The HART communicator requires a minimum loop resistance of 250 for communication. 3051S SIS Safety Transmitter (output code B) 3051S HART Diagnostics Transmitter (option code DA1) Maximum Loop Resistance = 3.5 * (Power Supply Voltage 12.0) Load (Ohms) Operating Region Voltage (V dc) 2. The HART communicator requires a minimum loop resistance of 250 for communication. HART Diagnostics Suite (Option DA1) The 3051S HART Diagnostics Transmitter provides Abnormal Situation Prevention (ASP) indication, device operating hours, variable logging, loop output readback diagnostic, and enhanced EDDL graphic displays for easy visual analysis. The integral statistical process monitoring (SPM) technology calculates the mean and standard deviation of the process variable 22 times per second and makes them available to the user. The 3051S ASP algorithm uses these values and highly flexible configuration options for customization to detect many user-defined or application specific abnormal situations (e.g. plugged impulse line detection). The device operating hours are logged along with the occurrence of diagnostic events to enable quick troubleshooting of application and installation issues. FOUNDATION fieldbus Power Supply External power supply required; transmitters operate on 9.0 to 32.0 V dc transmitter terminal voltage. Current Draw 17.5 ma for all configurations (including LCD display option) FOUNDATION fieldbus Parameters Schedule Entries Links Virtual Communications Relationships (VCR) 1 (max.) 30 (max.) 20 (max.) Standard Function Blocks Resource Block Contains hardware, electronics, and diagnostic information. Transducer Block Contains actual sensor measurement data including the sensor diagnostics and the ability to trim the pressure sensor or recall factory defaults. LCD Block Configures the local display. 2 Analog Input Blocks Processes the measurements for input into other function blocks. The output value is in engineering or custom units and contains a status indicating measurement quality. PID Block with Auto-tune Contains all logic to perform PID control in the field including cascade and feedforward. Auto-tune capability allows for superior tuning for optimized control performance. Backup Link Active Scheduler (LAS) The transmitter can function as a Link Active Scheduler if the current link master device fails or is removed from the segment. Software Upgrade in the Field Software for the 3051S with FOUNDATION fieldbus is easy to upgrade in the field using the FOUNDATION fieldbus Common Device Software Download procedure. PlantWeb Alerts Enable the full power of the PlantWeb digital architecture by diagnosing instrumentation issues, communicating advisory, maintenance, and failure details, and recommending a solution. Advanced Control Function Block Suite (Option A01) Input Selector Block Selects between inputs and generates an output using specific selection strategies such as minimum, maximum, midpoint, average, or first good. Arithmetic Block Provides pre-defined application-based equations including flow with partial density compensation, electronic remote seals, hydrostatic tank gauging, ratio control and others. Signal Characterizer Block Characterizes or approximates any function that defines an input/output relationship by configuring up to twenty X, Y coordinates. The block interpolates an output value for a given input value using the curve defined by the configured coordinates. Integrator Bock Compares the integrated or accumulated value from one or two variables to pre-trip and trip limits and generates discrete output signals when the limits are reached. This block is useful for calculating total flow, total mass, or volume over time. 5

3 , Rev EA Output Splitter Block Splits the output of one PID or other control block so that the PID will control two valves or other actuators. Control Selector Block Selects one of up to three inputs (highest, middle, or lowest) that are normally connected to the outputs of PID or other control function blocks. Block Execution Time Resource - Transducer - LCD Block - Analog Input 1, 2 20 milliseconds PID with Auto-tune 25 milliseconds Input Selector 20 milliseconds Arithmetic 20 milliseconds Signal Characterizer 20 milliseconds Integrator 20 milliseconds Output Splitter 20 milliseconds Control Selector 20 milliseconds Fully Compensated Mass Flow Block (Option H01) Calculates fully compensated mass flow based on differential pressure with external process pressure and temperature measurements over the fieldbus segment. Configuration for the mass flow calculation is easily accomplished using the Rosemount 3095 Engineering Assistant. FOUNDATION fieldbus Diagnostics Suite (Option D01) 3051S FOUNDATION fieldbus Diagnostics provide Abnormal Situation Prevention (ASP) indication and enhanced EDDL graphic displays for easy visual analysis. The integral statistical process monitoring (SPM) technology calculates the mean and standard deviation of the process variable 22 times per second and makes them available to the user. The 3051S ASP algorithm uses these values and highly flexible configuration options for customization to detect many user-defined or application specific abnormal situations (e.g. plugged impulse line detection). Process Temperature Limits Direct Mount Electronics 500 F (260 C) 750 F (00 C) when used with a direct mount, high temperature 5-valve manifold (Electronics Connection Platform code 6) Remote Mount Electronics 1250 F (677 C) Hastelloy Sensor Material 850 F (5 C) Stainless Steel Sensor Material Electronics Temperature Limits Ambient 0 to 185 F ( 0 to 85 C) With Integral Mount LCD Display: to 175 F ( 20 to 80 C) Storage 50 to 230 F ( 6 to 110 C) With Integral Mount LCD Display: 0 to 185 F ( 0 to 85 C) Pressure Limits (1) Direct Mount Electronics Pressure retention per ANSI B # or DIN PN Static Pressure Limits Range 1A: Operates within specification between static line pressures of 0.5 psia to 2000 psig (0.03 to 138 bar) Ranges 2A 3A: Operates within specifications between static line pressures of 0.5 psia and 3626 psig (0.03 bar-a to 250 bar-g) Burst Pressure Limits Coplanar or traditional process flange psig (689,5 bar). Overpressure Limits Flowmeters withstand the following limits without damage: Range 1A: 2000 psig (138 bar) Ranges 2A 3A: 3626 psig (250 bar) TABLE 2. Overpressure Limits (1) Standard Type Humidity Limits 0 100% relative humidity Carbon Steel Rating Stainless Steel Rating ANSI/ASME Class (20) 275 (19) ANSI/ASME Class (51) 720 (50) ANSI/ASME Class (102) 10 (99) At 100 F (38 C), the rating decreases with increasing temperature. DIN PN 10/0 580 (0) 580 (0) DIN PN 10/ (16) 232 (16) DIN PN 25/0 580 (0) 580 (0) At 28 F (120 C), the rating decreases with increasing temperature. (1) Carbon Steel and Stainless Steel Ratings are measured in psig (bar). Turn-On Time Performance within specifications less than 2 seconds (typical) after power is applied to the transmitter Damping Analog output response to a step input change is user-selectable from 0 to 60 seconds for one time constant. This software damping is in addition to sensor module response time Failure Mode Alarm HART -20mA (output option codes A and B) If self-diagnostics detect a gross transmitter failure, the analog signal will be driven offscale to alert the user. Rosemount standard (default), NAMUR, and custom alarm levels are available (see Table 3). High or low alarm signal is software-selectable or hardware-selectable via the optional switch (option D1). (1) Static pressure selection may effect pressure limitations. 6

4 , Rev EA The Annubar Flowmeter Series TABLE 3. Alarm Configuration High Alarm Low Alarm Default ma 3.75 ma NAMUR compliant (1) 22.5 ma 3.6 ma (2) (3) Custom levels ma ma (1) Analog output levels are compliant with NAMUR recommendation NE 3, see option codes C or C5. (2) Low alarm must be 0.1 ma less than low saturation and high alarm must be 0.1 ma greater than high saturation. (3) Not available with the 3051S SIS Safety Transmitter. 3051S SIS Safety Transmitter Failure Values Safety accuracy: 2.0% (1) Safety response time: 1.5 seconds (1) A 2% variation of the transmitter ma output is allowed before a safety trip. Trip values in the DCS or safety logic solver should be derated by 2%. Dynamic Performance Total Response Time (Td + Tc) (3) : 3051S_C, Ranges 2A - 3A: Range 1A: - 20 ma (HART ) (1) Fieldbus protocol (2) Typical Transmitter Response Time 100 milliseconds 255 milliseconds 152 milliseconds 307 milliseconds Transmitter Output vs. Time Process Variable Response Time 3051S SIS, Ranges 2A - 3A: Range 1A: 220 milliseconds 375 milliseconds Not Applicable Not Applicable Dead Time (Td) () 5 milliseconds (nominal) 97 milliseconds Update Rate 3051S 3051S SIS 22 times per second 11 times per second 22 times per second Not Applicable Pressure Released T d 100% 36.8% 0% T c Time T d = Dead Time T c = Time Constant Response Time = T d +T c 63.2% of Total Step Change _17A (1) Dead time and update rate apply to all models and ranges; analog output only (2) Transmitter fieldbus output only, segment macro-cycle not included. (3) Nominal total response time at 75 F (2 C) reference conditions. For option code DA1, add 0 milliseconds (nominal) to -20 ma (HART ) total response time values. () For option code DA1, dead time (Td) is 85 milliseconds (nominal). 7

5 , Rev EA Straight Run Requirements Flowmeter Orientation Upstream Dimensions Gas (Horizontal) Without Vanes (1) In Plane A With Vanes (2) Out of Plane A A C C Downstream Recommended Zone 120 degrees 30 degrees 30 degrees 8 2 Liquid and Steam (Horizontal) degrees 30 degrees degrees Recommended Zone Gas (Vertical) Flow degrees Steam (Vertical) degrees Flow (1) In Plane A means the bar is in the same plane as the elbow. Out of Plane A means the bar is perpendicular to the plane of the elbow. (2) Use straightening vane to reduce the required straight run length. Drill Hole Size According to Sensor Size Sensor Size Diameter 1 3 /-in. (19 mm) /16-in. (3 mm) /2-in. (6 mm) 8

6 , Rev EA The Annubar Flowmeter Series Physical Temperature Measurement Integral RTD 100 Ohm platinum RTD -wire RTD ( = ) Remote RTD 100 Ohm platinum RTD, spring loaded with 1 /2-in. NPT nipple and union (078 series with Rosemount 6 housing) Thermowell with Remote RTD 1 /2-in. x 1 /2-in NPT, 316 Stainless Steel with 1 /2-in. weld couplet to match pipe material Electronic Connections 1 /2 1 NPT, G 1 /2, and M (CM20) conduit. HART interface connections fixed to terminal block for output code A Annubar Sensor Material 316 Stainless Steel Hastelloy 276 Annubar Type See Dimensional Drawings on page 1 Pak-Lok Model (option P) Provided with a compression sealing mechanism rated up to 600# ANSI (10 psig at 100 F (99 bar at 38 C)) Graphite Packing ( 300 to 850 F ( 18 to 5 C)) Flanged with Opposite Side Support Model (option F) Provided with opposite side support, which is the same material as the pipe and requires a second pipe penetration Sensor flange is the same material as the Annubar sensor and the mounting flange is the same material as the pipe material Flanged mounting hardware: nuts, bolts and gaskets (constructed from the same material as the pipe material) SST: ( 300 to 850 F ( 18 to 5 C)) Hastelloy: ( 300 to 1250 F ( 18 to 677 C)) Flange Lok Model (option L) Flange Lok assembly is supplied in 316 SST material. Flange-Lok mounting hardware: nuts, bolts and gaskets (constructed from the same material as the pipe material) 300 to 850 F ( 18 to 5 C) Flo-Tap Models (options G and M) Opposite side support is not available Threaded connection is not available with Sensor Size 3 Gear Drive is not available with Sensor Size 1 Packing gland required Packing Gland Material Temperature Limits Teflon (PTFE): 0 to 00 F ( 0 to 20 C) Graphite: 300 to 850 F ( 18 to 5 C) Isolation valve included The isolation valve will carry the same pressure rating as the sensor flange and mounting flange specified in the mounting type Ball valves have a 300# limitation For threaded flo-tap models, the isolation valve NPT size is 1 1 /-in. (Sensor Size one) and 2-in. (Sensor Size 2). Annubar Type Specification Chart Option Description Pak-Lok (1) Flange-Lok Flange (1) Available up to 600# ANSI (10 psig at 100 F (99 bar at 38 C)) rating. Instrument Connections Temperature Ranges TABLE. Minimum / Maximum Temperature Range Manual and Gear Drive Flo-Tap T1 (1) Pak-Lok Body X Threaded connection X A1 150# RF ANSI X X X A3 300# RF ANSI X X X A6 600# RF ANSI X X X A9 (2) 900# RF ANSI X AF (2) 1500# RF ANSI X AT (2) 2500# RF ANSI X D1 DN PN 16 X X X D3 DN PN 0 X X X D6 DN PN 100 X X X R9 (2) 900# RTJ Flange X RF (2) 1500# RTJ Flange X RT (2) 2500# RTJ Flange X (2) Remote mount only. Description Temperature G1 Needle Valves, Carbon Steel 20 to 500 F ( 29 to 260 C) G2 Needle Valves, Stainless Steel 0 to 600 F ( 0 to 316 C) G3 Needle Valves, Hastelloy 0 to 600 F ( 0 to 316 C) G5 OS&Y Gate Valve, Carbon Steel 20 to 775 F ( 29 to 13 C) G6 OS&Y Gate Valve, Stainless Steel 0 to 850 F ( 0 to 5 C) G7 OS&Y Gate Valve, Hastelloy 0 to 1250 F ( 0 to 677 C) 9

7 , Rev EA Flowmeter Installed in Flanged Pipe Spool Section (option codes H3, H, and H5) All pipe spool sections are flanged pipe sections The flanged pipe spool section is constructed from the same material as the pipe Consult the factory for remote temperature measurement and ANSI ratings above 600# and DIN flanges TABLE 5. Flanged Pipe Spool Section Schedule ANSI 150# ANSI 0 300# ANSI 0 600# ANSI 80 Schedule TABLE 6. Flange Pipe Spool Section Length Nominal Pipe Size 2-in. (50 mm) 3-in. (80 mm) -in. (100 mm) 6-in. (150 mm) 8-in. (200 mm) Length in. (267.2 mm) in. (288.8 mm) 12.7-in. (323.6 mm) 1.33-in. (36.0 mm) in. (21.1 mm) Process-Wetted Parts Integral Manifolds 316 SST Hastelloy C-276 Remote Manifolds 316 SST Hastelloy C-276 Transmitter Vent Valves and Process Flanges 316 SST Hastelloy C-276 Process Isolating Diaphragms 316L SST Hastelloy C-276 O-rings Glass-filled TFE Integral Manifold O-Rings Teflon (PTFE) / Graphite Non-Wetted Parts Sensor Module Fill Fluid Silicone oil Inert Fill optional Cover O-rings Buna-N Remote Mounting Brackets SST Sensor mounting (including nuts, bolts, and gasket) Match Process Pipe material Electronic Housing Low copper aluminum, NEMA x, IP65 SST (optional) Paint Polyurethane Bolts CS 10

8 , Rev EA The Annubar Flowmeter Series PRODUCT CERTIFICATIONS Approved Manufacturing Locations Rosemount Inc. Chanhassen, Minnesota USA Emerson Process Management GmbH & Co. Wessling, Germany Emerson Process Management Asia Pacific Private Limited Singapore Beijing Rosemount Far East Instrument Co., LTD Beijing, China European Directive Information The EC declaration of conformity for all applicable European directives for this product can be found at A hard copy may be obtained by contacting an Emerson Process Management representative. ATEX Directive (9/9/EC) Emerson Process Management complies with the ATEX Directive. European Pressure Equipment Directive (PED) (97/23/EC) Models 3051S_CA; 3051S_CD2, 3,, 5; (also with P9 option) Pressure Transmitters QS Certificate of Assessment - EC No. PED-H-20, Module H Conformity Assessment All other Model 3051S Pressure Transmitters Sound Engineering Practice Transmitter Attachments: Diaphragm Seal - Process Flange - Manifold Sound Engineering Practice Primary Elements, Flowmeter See appropriate Primary Element QIG Electro Magnetic Compatibility (EMC) (89/336/EEC) All Models: EN : 1992; EN :1995; EN :1997 Industrial Ordinary Location Certification for FM As standard, the transmitter has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA). Hazardous Locations Certifications North American Certifications FM Approvals E5 Explosion-proof for Class I, Division 1, Groups B, C, and D; dust-ignition proof for Class II and Class III, Division 1, Groups E, F, and G; hazardous locations; enclosure Type X, conduit seal not required when installed according to Rosemount drawing I5/IE Intrinsically Safe for use in Class I, Division 1, Groups A, B, C, and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1; Class I, Zone 0 AEx ia IIC when connected in accordance with Rosemount drawing ; Non-incendive for Class I, Division 2, Groups A, B, C, and D Enclosure Type X For entity parameters see control drawing Canadian Standards Association (CSA) E6 Explosion-proof for Class I, Division 1, Groups B, C, and D; Dust-Ignition-Proof for Class II and Class III, Division 1, Groups E, F, and G; suitable for Class I, Division 2, Groups A, B, C, and D, when installed per Rosemount drawing , CSA Enclosure Type X; conduit seal not required. I6/IF Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D when connected in accordance with Rosemount drawings ; For entity parameters see control drawing European Certifications I1/IA ATEX Intrinsic Safety Certificate No.: BAS01ATEX1303X EEx ia IIC T5 (-60 C T a 0 C) T (-60 C T a 70 C) T (-60 C T a 0 C) (FISCO) 1180 TABLE 7. Input Parameters Loop / Power U i = 30 V U i = 17.5 V I i = 300 ma I i = 380 ma P i = 1.0 W P i = 1.3 W P i = 5.32 W C i = 30 nf C i = 11. nf C i = 0 L i = 0 L i = 60 µh II 1G Groups HART / FOUNDATION fieldbus/ Remote Display / SIS FISCO HART / FOUNDATION fieldbus/ Remote Display / SIS FISCO HART / Remote Display / SIS FOUNDATION fieldbus FISCO SuperModule Platform HART / SIS FOUNDATION fieldbus / Remote Display / FISCO HART / FOUNDATION fieldbus/ SIS / FISCO Remote Display Special conditions for safe use (x) 1. The apparatus, excluding the Types 3051 S-T and 3051 S-C (In-line and Coplanar SuperModules respectively), is not capable of withstanding the 500V test as defined in Clause of EN This must be considered during installation. 2. The terminal pins of the Types 3051 S-T and 3051 S-C must be protected to IP20 minimum. 11

9 , Rev EA N1 ND E1 ATEX Type n Certificate No.: BAS01ATEX330X II 3 G EEx nl IIC T5 (T a = -0 C TO 70 C) Ui = 5 Vdc max IP66 Special conditions for safe use (x) The apparatus is not capable of withstanding the 500V insulation test required by Clause 9.1 of EN 50021: This must be taken into account when installing the apparatus. ATEX Dust Certificate No.: BAS01ATEX137X II 1 D T105 C (-20 C T amb 85 C) V max = 2. volts max A = 2 ma IP Special conditions for safe use (x) 1. The user must ensure that the maximum rated voltage and current (2. volts, 22 milliampere, DC) are not exceeded. All connections to other apparatus or associated apparatus shall have control over this voltage and current equivalent to a category ib circuit according to EN Cable entries must be used which maintain the ingress protection of the enclosure to at least IP Unused cable entries must be filled with suitable blanking plugs which maintain the ingress protection of the enclosure to at least IP66.. Cable entries and blanking plugs must be suitable for the ambient range of the apparatus and capable of withstanding a 7J impact test. 5. The 3051S must be securely screwed in place to maintain the ingress protection of the enclosure. ATEX Flameproof Certificate No.: KEMA00ATEX213X II 1/2 G EEx d IIC T6 (-50 C T amb 65 C) EEx d IIC T5 (-50 C T amb 80 C) V max = 2.V 1180 Special conditions for safe use (x) This device contains a thin wall diaphragm. Installation, maintenance and use shall take into account the environmental conditions to which the diaphragm will be subjected. The manufacturer s instructions for installation and maintenance shall be followed in detail to assure safety during its expected lifetime. The Model 3051S pressure transmitter must include a Series 300S housing integrally mounted to a Series Model 3051S Sensor module as per Rosemount drawing Japanese Certifications E JIS Flameproof Ex d IIC T6 Australian Certifications E7 Certificate TC15682 TC15683 TC1568 TC15685 TC15686 TC15687 TC15688 TC15689 TC15690 Description Coplanar with Junction Box Housing Coplanar with PlantWeb Housing Coplanar with PlantWeb Housing and LCD Display In-Line SST with Junction Box Housing In-Line Hastelloy with Junction Box Housing In-Line SST with PlantWeb Housing In-Line Hastelloy with Plantweb Housing In-Line SST with Plantweb Housing and LCD Display In-Line Hastelloy with PlantWeb Housing and LCD Display SAA Explosion-proof and DIP Certification No.: AUS Ex 3798X Ex d IIC T6 (T a = 60 C) IP66 DIP A21 TA T6 (T a = 60 C) IP66 Special conditions for safe use (x) 1. It is a condition of manufacture that each transmitter module shall be pressure tested in accordance with clause.3 of AS at minimum pressure of 150 kpa. As the model 300S housing passed tests at times the reference pressures (00 kpa for single and 3800 kpa for dual compartment housing) and are not of welded construction, they may be exempted from the routing pressure test of clause.3 of AS It is a condition of manufacture that each transmitter module and housing combination shall be subjected to a routine high voltage test in accordance with clause 6.2 of AS , with the following variation. The test voltage applied to each single or dual compartment housing shall not be less than 500 V, 7 to 62 Hz, for a period of not less than one minute, with a breakdown current of less than 5 ma. 3. It is a condition of safe use that each housing shall be connected to external circuits via suitable conduit or Standards Australia certified cable glands. Where only one entry is used for connection to external circuits, the unused entry shall be closed by means of the blanking plug supplied by the equipment manufacturer or by a suitable Standards Australia certified blanking plug.. It is a condition of safe use that a dielectric strength test shall be applied whenever the terminal block is changed or replaced in either the dual compartment or single compartment housings. The breakdown current shall be less than 5 ma, when 500 V, 7 to 62 Hz, is applied for one minute. Note: if tested with an optional T1 transient protector terminal block fitted, the protection will operate and hence there will be no current indicated. 5. It is a condition of safe use that each transmitter module shall be used with a Model 300S housing, in order to comply with flameproof requirements. 12

10 , Rev EA The Annubar Flowmeter Series 6. It is a condition of safe use that each model 300S housing fitted with a transmitter module shall be marked with the same certification marking code information. Should the housing be replaced after initial supply to another model 300S housing, the replacement housing shall have the same certification marking code information as the housing it replaces. IECEx Certifications I7/IG IECEx Intrinsic Safety Certificate No.: IECExBAS0.0017X Ex ia IIC T5 (T a = -60 C to 0 C) -HART/SIS/Remote Meter Ex ia IIC T (T a = -60 C to 70 C) -HART/SIS/Remote Meter Ex ia IIC T (T a = -60 C to 70 C) -FOUNDATION Fieldbus Ex ia IIC T (T a = -60 C to 0 C) -FISCO IP66 TABLE 8. Input Parameters Loop / Power U i = 30 V U i = 17.5 V I i = 300 ma I i = 380 ma P i = 1.0 W P i = 1.3 W P i = 5.32 W C i = 30 nf C i = 11. nf C i = 0 L i = 0 Groups HART / FOUNDATION fieldbus/ Remote Display / SIS FISCO HART / FOUNDATION fieldbus/ Remote Display / SIS FISCO HART / Remote Display / SIS FOUNDATION fieldbus FISCO SuperModule Platform HART / SIS FOUNDATION fieldbus / Remote Display / FISCO HART / FOUNDATION fieldbus/ SIS / FISCO N7 IECEx Type n Certificate No.: IECExBAS0.0018X Ex nc IIC T5 (Ta = -0 C to 70 C) Ui = 5 Vdc MAX IP66 Special conditions for safe use (x) The apparatus is not capable of withstanding the 500 V insulation test required by Clause 8 of IEC 79-15: Combinations of Certifications Stainless steel certification tag is provided when optional approval is specified. Once a device labeled with multiple approval types is installed, it should not be reinstalled using any other approval types. Permanently mark the approval label to distinguish it from unused approval types. K1 Combination of E1, I1, N1, and ND K5 Combination of E5 and I5 K6 Combination of E6 and I6 K7 Combination of E7, I7, and N7 KA Combination of E1, I1, E6, and I6 KB Combination of E5, I5, I6 and E6 KC Combination of E5, E1, I5 and I1 KD Combination of E5, I5, E6, I6, E1, and I1 Special conditions for safe use (x) 1.The Models 3051S HART -20mA, 3051S Fieldbus, 3051S Profibus and 3051S FISCO are not capable of withstanding the 500V test as defined in clause of IEC This must be taken into account during installation. 2.The terminal pins of the Types 3051S-T and 3051S-C must be protected to IP20 minimum. 13

11 , Rev EA DIMENSIONAL DRAWINGS Pak-Lok ProBar Flowmeter (1) Front View Side View Top View D B C A (1) The Pak-Lok Annubar model is available up to 600# ANSI (10 psig at 100 F (99 bar at 38 C)). TABLE 9. Pak-Lok ProBar Flowmeter Dimensional Data Sensor Size A (Max) B (Max) C (Max) D (Max) (190.5) (07.2) 9.00 (228.6) 6.90 (175.3) (235.0) (51.6) 9.00 (228.6) 6.90 (175.3) (30.8) (508.8) 9.00 (228.6) 6.90 (175.3) Dimensions are in inches (millimeters) 1

12 , Rev EA The Annubar Flowmeter Series Flange-Lok ProBar Flowmeter (1) Front View Side View Top View E C D B A (1) The Flange-Lok Annubar model can be direct mounted up to 600# ANSI (10 psig at 100 F (99 bar at 38 C)). TABLE 10. Flange-Lok ProBar Flowmeter Dimensional Data Sensor Size Flange Size and Rating A ± (3.2) B ± 0.25 (6.) C (Max) D (Max) E (Max) /2 150# 3.88 (98.6) (311.2) (527.8) 9.00 (228.6) (285.8) /2 300#.13 (10.9) (311.2) (527.8) 9.00 (228.6) (285.8) /2 600#. (112.8) (311.2) (527.8) 9.00 (228.6) (285.8) 1 DN0/PN (78.5) (311.2) (527.8) 9.00 (228.6) (285.8) 1 DN0/PN (81.5) (311.2) (527.8) 9.00 (228.6) (285.8) 1 DN0/ PN (98.6) (311.2) (527.8) 9.00 (228.6) (285.8) #.13 (10.9) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) #.38 (111.3) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) #.76 (120.9) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) 2 DN50/PN (86.) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) 2 DN50/PN (89.2) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) 2 DN50/ PN (109.2) 1.25 (362.0) (578.6) 9.00 (228.6) (285.8) #.63 (117.6) (.5) (661.2) 9.00 (228.6) (285.8) # 5.00 (127.0) (.5) (661.2) 9.00 (228.6) (285.8) # 5.38 (136.7) (.5) (661.2) 9.00 (228.6) (285.8) 3 DN80/PN (97.5) (.5) (661.2) 9.00 (228.6) (285.8) 3 DN80/PN0.16 (105.7) (.5) (661.2) 9.00 (228.6) (285.8) 3 DN80/ PN (125.7) (.5) (661.2) 9.00 (228.6) (285.8) Dimensions are in inches (millimeters) 15

13 , Rev EA Flanged ProBar Flowmeter Front View Side View Top View E B C D A F TABLE 11. Flanged ProBar Flowmeter Dimensional Data Flange Size and A ± B ± 0.25 C ± 0.25 Sensor Size Rating (3.2) (6.) (6.) D (Max) E (Max) F (Max) /2 150# 3.88 (98.6) (279.) (96.1) 9.00 (228.6) 6.30 (160.0) 3.50 (88.9) /2 300#.13 (10.9) (279.) (96.1) 9.00 (228.6) 6.86 (17.2) 3.50 (88.9) /2 600#. (112.8) (279.) (96.1) 9.00(228.6) 6.86 (17.2) 3.50 (88.9) 1 DN0/PN (78.5) (279.) (96.1) 9.00 (228.6) 6.86 (17.2) 3.50 (88.9) 1 DN0/PN (81.5) (279.) (96.1) 9.00 (228.6) 6.86 (17.2) 3.50 (88.9) 1 DN0/ PN (98.6) (279.) (96.1) 9.00(228.6) 6.86 (17.2) 3.50 (88.9) /2 900#.9 (125.5) 9.32 (236.6) 3.50 (88.9) /2 1500#.9 (125.5) 9.32 (236.6) 3.50 (88.9) /2 2500# 6.76 (171.7) 11.6 (295.5).00 (101.6) #.13 (10.9) (30.8) (521.5) 9.00 (228.6) 6.80 (172.7) 5.00 (127.0) #.38 (111.3) (30.8) (521.5) 9.00 (228.6) 7.05 (179.1) 5.00 (127.0) #.76 (120.9) (30.8) (521.5) 9.00 (228.6) 7.05 (179.1) 5.00 (127.0) 2 DN50/PN (86.) (30.8) (521.5) 9.00 (228.6) 7.05 (179.1) 5.00 (127.0) 2 DN50/PN (89.2) (30.8) (521.5) 9.00 (228.6) 7.05 (179.1) 5.00 (127.0) 2 DN50/ PN (109.2) (30.8) (521.5) 9.00 (228.6) 7.05 (179.1) 5.00 (127.0) # 5.88 (19.) (266.8) 5.00 (127.0) # 5.88 (19.) (266.8) 5.00 (127.0) # 9.87 (250.7) (396.7).50 (11.3) #.63 (117.6) (32.9) (559.6) 9.00 (228.6) 7.55 (191.8).00 (101.6) # 5.00 (127.0) (32.9) (559.6) 9.00 (228.6) 7.93 (201.3).00 (101.6) Table 11 Continued on Next Page 16

14 , Rev EA The Annubar Flowmeter Series TABLE 11. Flanged ProBar Flowmeter Dimensional Data Flange Size and A ± B ± 0.25 C ± 0.25 Sensor Size Rating (3.2) (6.) (6.) D (Max) E (Max) F (Max) # 5.38 (136.7) (32.9) (559.6) 9.00 (228.6) 7.93 (201.3).00 (101.6) 3 DN80/PN (97.5) (32.9) (559.6) 9.00 (228.6) 7.93 (201.3).00 (101.6) 3 DN80/PN0.16 (105.7) (32.9) (559.6) 9.00 (228.6) 7.93 (201.3).00 (101.6) 3 DN80/ PN (125.7) (32.9) (559.6) 9.00 (228.6) 7.93 (201.3).00 (101.6) 3 900# 8.19 (208.0) 13. (31.3) 7.00 (177.8) # 8.56 (217.) (350.8) 7.00 (177.8) # (28.2) (39.8) 7.00 (177.8) Dimensions are in inches (millimeters) 17

15 , Rev EA Flanged Flo-Tap ProBar Flowmeter (1) Front View Side View Top View F D E C B A (1) The Flanged Flo-Tap ProBar Flowmeter is available with both the manual and gear drive options. TABLE 12. Flanged Flo-Tap ProBar Flowmeter Dimensional Data Sensor Size Flange Size and Rating A ± (3.2) B ± 0.25 (6.) Note: Customer Supplied. Inserted, C Dimension = Pipe I.D. + Wall Thickness + B + C I Retracted, C Dimension = 2 x (Pipe I.D. + Wall Thickness + B) + C I C I (Max) (Gear Drive) C I (Max) (Manual) D (Max) E (Max) F (Max) /2 150# 3.88 (98.5) (266.7) 17.9 (5.7) C (216.7) (266.7) (285.8) /2 300#.13 (10.9) (298.5) 17.9 (5.7) C (216.7) (266.7) (285.8) /2 600#. (112.8) 1.06 (357.2) 17.9 (5.7) C (216.7) (266.7) (285.8) 1 DN0/PN (78.5) See Note (5.7) C (216.7) (266.7) (285.8) 1 DN0/PN (81.5) See Note (5.7) C (216.7) (266.7) (285.8) 1 DN0/PN (98.6) See Note (5.7) C (216.7) (266.7) (285.8) #.13 (10.9) (285.8) 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) #.38 (111.3) (330.2) 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) #.76 (120.9) (16.0) 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) 2 DN50/PN (86.) See Note. 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) 2 DN50/PN (89.2) See Note. 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) 2 DN50/PN (109.2) See Note. 2.6 (62.8) 21. (53.6) C (216.7) (319.0) (285.8) #.63 (117.6) (323.9) 26.5 (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) # 5.00 (127.0) (12.8) 26.5 (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) # 5.38 (136.7) (95.) 26.5 (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) 3 DN80/PN (97.5) See Note (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) 3 DN80/PN0.16 (105.7) See Note (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) 3 DN80/PN (125.7) See Note (673.1) 23.3 (591.8) C (216.7) 1.13 (358.9) (285.8) Dimensions are in inches (millimeters) 18

16 , Rev EA The Annubar Flowmeter Series Threaded Flo-Tap ProBar Flowmeter (1) Front View Side View Top View E C D B A (1) The Flanged Flo-Tap ProBar Flowmeter is available with both the manual and gear drive options. TABLE 13. Threaded Flo-Tap ProBar Flowmeter Dimensional Data Sensor Size A ± 0.50 (12.7) B I (Max) (Gear Drive) B I (Max) (Manual) C (Max) D (Max) E (Max) (171.8) 17.0 (2.0) B (216.7) (266.7) 6.90 (175.3) (207.5) (602.0) (528.3) B (216.7) (319.0) 6.90 (175.3) Sensor Size 3 is not available in a Threaded Flo-Tap. Dimensions are in inches (millimeters) Inserted, B Dimension = Pipe I.D. + Wall Thickness + A + B I Retracted, B Dimension = 2 x (Pipe I.D. + Wall Thickness + A) + B I 19

17 , Rev EA ORDERING INFORMATION Rosemount 3051SFA ProBar Flowmeter Ordering Information Model 3051SFA D L G S Product Description ProBar Flowmeter Measurement Type Differential Pressure Fluid Type Liquid Gas Steam Line Size Line Size in. (50 mm) in. (50 mm) /2-in. (63.5 mm) in. (500 mm) in. (80 mm) 20 2-in. (600 mm) /2-in. (89 mm) in. (750 mm) 00 -in. (100 mm) in. (900 mm) in. (125 mm) 20 2-in. (1066 mm) in. (150 mm) 80 8-in. (1210 mm) in. (175 mm) in. (1520 mm) in. (200 mm) in. (1820 mm) in. (250 mm) in (1950 mm) in. (300 mm) 80 8-in. (2100 mm) 10 1-in. (350 mm) in. (2250 mm) in. (00 mm) in (200 mm) Pipe I.D. Range (Refer to the Pipe I.D. Range measured in inches (millimeters) on page 26) A Range A from the Pipe I.D. table B Range B from the Pipe I.D. table C Range C from the Pipe I.D. table D Range D from the Pipe I.D. table E Range E from the Pipe I.D. table Z Non-standard Pipe I.D. Range or Line Sizes greater than 12 inches Pipe Material / Mounting Assembly Material C Carbon steel S 316 Stainless Steel G Chrome-Moly Grade F-11 N Chrome-Moly Grade F-22 J Chrome-Moly Grade F-91 0 (1) No Mounting (Customer Supplied) H D U P F L G M Piping Orientation Horizontal Piping Vertical Piping with Downwards Flow Vertical Piping with Upwards Flow Annubar Type Pak-Lok Flanged with opposite side support Flange-Lok Gear-Drive Flo-Tap Manual Flo-Tap Sensor Material S 316 Stainless Steel H Hastelloy C

18 , Rev EA The Annubar Flowmeter Series Rosemount 3051SFA ProBar Flowmeter Ordering Information Sensor Size 1 Sensor size 1 Line sizes 2-in. (50 mm) to 8-in. (200 mm) 2 Sensor size 2 Line sizes 6-in. (150 mm) to 96-in. (200 mm) 3 Sensor size 3 Line sizes greater than 12-in. (300 mm) Mounting Type T1 Compression or Threaded Connection A1 150# RF ANSI A3 300# RF ANSI A6 600# RF ANSI A9 (2) 900# RF ANSI AF (2) 1500# RF ANSI AT (2) 2500 # RF ANSI D1 DN PN16 Flange D3 DN PN0 Flange D6 DN PN100 Flange R9 (2) 900# RTJ Flange RF (2) 1500# RTJ Flange RT (2) 2500# RTJ Flange Opposite Side Support and Packing Gland 0 No opposite side support or packing gland (Required for Pak-Lok and Flange-Lok models) Opposite Side Support Required for Flanged Models C NPT Threaded Opposite Support Assembly Extended Tip D Welded Opposite Support Assembly Extended Tip Packing Gland Required for Flo-Tap Models Packing Gland Material Rod Material Packing Material J Stainless Steel Packing Gland / Cage Nipple Carbon Steel Teflon K Stainless Steel Packing Gland / Cage Nipple Stainless Steel Teflon L Stainless Steel Packing Gland / Cage Nipple Carbon Steel Graphite N Stainless Steel Packing Gland / Cage Nipple Stainless Steel Graphite R Hastelloy Packing Gland / Cage Nipple Stainless Steel Graphite Isolation Valve for Flo-Tap Models 1 Gate Valve, Carbon Steel 2 Gate Valve, Stainless Steel 5 Ball Valve, Carbon Steel 6 Ball Valve, Stainless Steel 0 (1) Not Applicable or Customer Supplied Temperature Measurement T Integral RTD not available with Flanged model greater than class 600 R Remote Thermowell and RTD 0 No Temperature Sensor Electronics Connection Platform 3 Direct-mount, Integral 3-valve manifold not available with Flanged model greater than class Direct -mount, 5-valve manifold not available with Flanged model greater than class Direct-mount, high temperature 5-valve manifold not available with Flanged model greater than class Remote-mount NPT Connections 8 Remote-mount SW Connections 1A 2A 3A Differential Pressure Ranges 0 to 25 in H 2 O (0 to 62.2 mbar) 0 to 250 in H 2 O (0 to 623 mbar) 0 to 1000 in H 2 O (0 to 2.5 bar) 21

19 , Rev EA Rosemount 3051SFA ProBar Flowmeter Ordering Information Output Protocol A 20 ma with digital signal based on HART protocol B (3) 20 ma Safety Certified with digital signal based on HART protocol F () FOUNDATION fieldbus protocol Electronics Housing Style Material Conduit Entry Size 1A PlantWeb Housing Aluminum 1 /2-1 NPT 1B PlantWeb Housing Aluminum M20 x 1.5 (CM20) 1C PlantWeb Housing Aluminum G 1 /2 1J PlantWeb Housing 316L SST 1 /2-1 NPT 1K PlantWeb Housing 316L SST M20 x 1.5 (CM20) 1L PlantWeb Housing 316L SST G 1 /2 2A Junction Box Housing Aluminum 1 /2-1 NPT 2B Junction Box Housing Aluminum M20 x 1.5 (CM20) 2C Junction Box Housing Aluminum G 1 /2 2E Junction Box housing with output for remote display and interface Aluminum 1 /2-1 NPT 2F Junction Box housing with output for remote display and interface Aluminum M20 x 1.5 (CM20) 2G Junction Box housing with output for remote display and interface Aluminum G 1 /2 2J Junction Box Housing 316L SST 1 /2-1 NPT 2M Junction Box housing with output for remote display and interface 316L SST 1 /2-1 NPT 7J (5) Quick Connect (A size Mini, -pin male termination) 316L SST Electronics Performance Class 3 (6) Ultra for Flow: up to 0.8% flow rate accuracy, 10:1 flow turndown, 10-year stability. limited 12-year warranty 1 (6) Ultra: up to 0.9% flow rate accuracy, 8:1 flow turndown, 10-year stability, limited 12-year warranty 2 Classic: up to 1.1% flow rate accuracy, 8:1 flow turndown, 5-year stability Options Pressure Testing P1 (7) Hydrostatic Testing with Certificate PX (7) Extended Hydrostatic Testing Special Cleaning P2 Cleaning for Special Processes PA Cleaning per ASTM G93 level D (section 11.) Material Testing V1 Dye Penetrant Exam Material Examination V2 Radiographic Examination Flow Calibration W1 Flow Calibration (Average K) WZ Special Calibration Special Inspection QC1 Visual and Dimensional Inspection with Certificate QC7 Inspection and Performance Certificate Surface Finish RL Surface finish for Low Pipe Reynolds Number in Gas and Steam RH Surface finish for High Pipe Reynolds Number in Liquid Material Traceability Certification Q8 (8) Material Certificate per ISO B and EN B 22

20 , Rev EA The Annubar Flowmeter Series Rosemount 3051SFA ProBar Flowmeter Ordering Information Conformance J1 Canadian Registration J2 (9) ANSI B31.1 J3 (9) ANSI B31.3 J (9) ANSI B31.8 J5 (10) NACE MR-0175 / ISO J6 European Pressure Directive (PED) Installed in Flanged Pipe Spool Section H3 150# Flanged Connection with Rosemount Standard Length and Schedule H 300# Flanged Connection with Rosemount Standard Length and Schedule H5 600# Flanged Connection with Rosemount Standard Length and Schedule Instrument Connections for Remote Mount Option G1 Needle Valves, Carbon Steel G2 Needle Valves, Stainless Steel G3 Needle Valves, Hastelloy G5 OS&Y Gate Valve, Carbon Steel G6 OS&Y Gate Valve, Stainless Steel G7 OS&Y Gate Valve, Hastelloy Special Shipment Y1 Mounting Hardware Shipped Separately Special Dimensions VM Variable Mounting VT Variable Tip VS Variable length Spool Section V9 Special Dimension Transmitter Calibration Certification Q Calibration Data Certificate for Transmitter QP Calibration Data Certificate and Tamper Evident Seal Safety Certification QS Certificate of FMEDA data Product Certifications E1 ATEX Flameproof I1 ATEX Intrinsically Safe N1 ATEX Type n IA (11) ATEX FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only K1 ATEX Flameproof, Intrinsically Safe, Type n, and Dust (combination of E1, I1, N1, and ND) ND ATEX Dust E5 FM Explosion-proof I5 FM Intrinsically Safe, Non-incendive IE (11) FM FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only K5 FM Explosion-proof, Intrinsically Safe, Non-incendive (combination of E5 and I5) E6 CSA Explosion-proof, Division 2 I6 CSA Intrinsically Safe IF (11) CSA FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only K6 CSA Explosion-proof, Intrinsically Safe, Division 2 (combination of E6 and I6) E7 (11) SAA Flameproof, Dust Ignition-proof I7 IECEx Intrinsically Safe IG (11) IECEx FISCO Intrinsically Safe N7 IECEx Type n K7 SAA Flameproof, Dust Ignition-proof, IECEx Intrinsically Safe, and Type n (combination of E7, I7, and N7) KA ATEX and CSA Flameproof, Intrinsically Safe (combination of E1, I1, E6, and I6) Note: Only available on Housing Style codes IA, IJ, 2A, 2J, 2E, or 2M. KB FM and CSA Explosion-proof, Intrinsically Safe, Division 2 (combination of E5, E6, I5, and I6) Note: Only available on Housing Style codes IA, IJ, 2A, 2J, 2E, or 2M. KC FM and ATEX Explosion-proof, Intrinsically Safe, Non-incendive (combination of E5, E1, I5, and I1) Note: Only available on Housing Style codes IA, IJ, 2A, 2J, 2E, or 2M. KD FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of E5, I5, E6, I6, E1, and I1) Note: Only available on Housing Style codes IA, IJ, 2A, 2J, 2E, or 2M. 23

21 , Rev EA Rosemount 3051SFA ProBar Flowmeter Ordering Information Alternate Transmitter Materials of Construction L1 Inert Sensor Fill Fluid L2 Graphite-Filled Teflon (PTFE) O-Ring LA Inert Sensor Fill Fluid and Graphite-Filled Teflon (PTFE) O-ring Display (12) M5 PlantWeb LCD display M7 (6)(13) Remote mount LCD display and interface, PlantWeb housing, no cable, SST bracket M8 (6)(13) Remote mount LCD display and interface, PlantWeb housing, 50 foot cable, SST bracket M9 (6)(13) Remote mount LCD display and interface, PlantWeb housing, 100 foot cable, SST bracket Terminal Blocks T1 (12) Transient terminal block T2 (1) Terminal block with WAGO spring clamp terminals T3 (1) Transient terminal block with WAGO spring clamp terminals Manifold for Remote Mount Option F1 3-Valve Manifold, Carbon Steel F2 3-Valve Manifold, Stainless Steel F3 3-Valve Manifold, Hastelloy C F5 5-Valve Manifold, Carbon Steel F6 5-Valve Manifold, Stainless Steel F7 5-Valve Manifold, Hastelloy C PlantWeb Control Functionality A01 (15) FOUNDATION fieldbus Advanced Control Function Block Suite PlantWeb Diagnostic Functionality D01 (15) FOUNDATION fieldbus Diagnostics Suite DA1 (16) HART Diagnostic Suite PlantWeb Enhanced Measurement Functionality H01 (15)(17) Fully Compensated Mass Flow Block Special Configuration (Software) C (18) NAMUR alarm and saturation signal levels, high alarm C5 (18) NAMUR alarm and saturation signal levels, low alarm C6 (6)(18) Custom alarm and saturation signal levels, high alarm Note: Requires option code C1, custom software configuration. A Configuration Data Sheet must be completed, see page 59. C7 (6)(18) Custom alarm and saturation signal levels, low alarm Note: Requires option code C1, custom software configuration. A Configuration Data Sheet must be completed, see page 59. C8 (18) Low alarm (standard Rosemount alarm and saturation signal levels) Special Configuration (Hardware) D1 (18) Hardware Adjustment (zero, span, security) D External Ground Screw DA (18) Hardware Adjustment (zero, span, security) and External Ground Screw Conduit Electrical Connector GE (19) M12, -pin, Male Connector (eurofast ) GM (19) A size Mini, -pin, Male Connector (minifast ) Typical Model Number: 3051SFA D L 060 D C H P S 2 T A A 1A 3 (1) Provide the A dimension for Flanged, Flange-Lok, and Threaded Flo-Tap models. Provide the B dimension for Flange Flo-Tap models. (2) Available in remote mount applications only. (3) Requires PlantWeb housing and Hardware Adjustments option code D1. () Requires PlantWeb housing. (5) Available with output code A only. Available approvals are FM Intrinsically Safe, Non-incendive (option code I5) or ATEX Instrinsically Safe (option code I1). Contact an Emerson Process Management representative for additional information. (6) Not available with output protocol code B. (7) Applies to assembled flowmeter only, mounting not tested. (8) Isolation and Instrument valves not included in Traceability Certification. 2

22 , Rev EA The Annubar Flowmeter Series (9) Not available with Electronics Connection Platform 6. (10) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments. (11) Consult factory for availability. (12) Not available with Housing code 7J. (13) Not available with Output Protocol code F or option code DA1. (1) Available with Output Protocol code A and Plantweb housing only. (15) Requires PlantWeb housing and output code F. (16) Requires PlantWeb housing and output code A. Includes Hardware Adjustments as standard. Contact an Emerson Process Management representative regarding availability. (17) Requires Rosemount 3095 Engineering Assistant to configure. (18) Not available with Output Protocol code F. (19) Not available with Housing code 7J. Available with Intrinsically Safe approvals only. For FM Intrinsically Safe, Non-incendive approval (option code I5) or FM FISCO Intrinsically Safe approval (option code IE), install in accordance with Rosemount drawing to maintain NEMA X rating. 25

23 , Rev EA Pipe I.D. Range measured in inches (millimeters) See Rosemount 3051SFA ProBar Flowmeter Ordering Information on page 20 For pipes with an Inner Diameter (I.D.) Range / Pipe Wall Thickness not found in this table or with a line size greater than 12-in. (300 mm), choose option code Z and specify the exact pipe dimensions (I.D. and Pipe Wall Thickness) on the HART Configuration Data Sheet (CDS) on page 59. The Emerson process Management Sizing program will determine this code, based on the application piping. Sensor Size 1 Sensor Size 2 Sensor Size 1 Sensor Size 2 Sensor Size 1 Sensor Size 2 Nominal 2-in. (50 mm) 2 1 /2-in. (63.5 mm) 3-in. (80 mm) 3 1 /2-in. (89 mm) -in. (100 mm) 5-in. (125 mm) 6-in. (150 mm) 6-in. (150 mm) 7-in. (180 mm) 7-in. (180 mm) 8-in. (200 mm) 8-in. (200 mm) 10-in. (250 mm) 12-in. (300 mm) Line Size Max. O.D in. (66.68 mm) in. (80.98 mm) 3.75-in. (95.25 mm).25-in. ( mm) in. ( mm) 6.09-in. (15.79 mm) 6.93-in. ( mm) 6.93-in. ( mm) 7.93-in. (201.2 mm) 7.93-in. (201.2 mm) in. (26.08 mm) in. (26.08 mm) in. (298.5 mm) in. ( mm) Pipe Wall Thickness I.D. Option Inner Diameter (I.D.) Range ANSI Pipes Non-ANSI Pipes Range 1.78 to 1.81-in. (5.31 to 6.76 mm) to 0.55-in to 0.88-in. (1.7 to 12. mm) A to in. (6.79 to 9.23 mm) (1.7 to 13.8 mm) to 0.9-in. (1.7 to 11. mm) B to in. (9.25 to mm) to 0.17-in. (1.7 to 10.6 mm) C to in. (52.53 to mm) to 0.07-in. (1.7 to 10.3 mm) D to in. (56.06 to mm) to in to 0.8-in. (2.1 to 11. mm) B to 2.69-in. (59.00 to mm) (2.1 to 1.3 mm) to 0.17-in. (2.1 to 10.6 mm) C 2.70 to in. (62.7 to mm) to 0.35-in. (2.1 to 11.0 mm) D to 2.67-in. (66.01 to mm) to in. (2.1 to 13.1 mm) E 2.68 to in. (67.26 to mm) to in to 0.60-in. (2.1 to 11.7 mm) A to in. (69.90 to mm) (2.1 to 1.3 mm) to 0.16-in. (2.1 to 10.6 mm) B to in. (73.66 to mm) to in. (2.1 to 10.0 mm) C to in. (77.95 to mm) to 0.0-in (2.1 to 10.3 mm) D to in. (82.02 to 8.66 mm) to in to 0.96-in. (3.0 to 12.6 mm) B to 3.58-in. (8.68 to mm) (3.0 to 15.2 mm) to in. (3.0 to 9.8 mm) C 3.59 to 3.73-in. (90.1 to 9.8 mm) to 0.15-in. (3.0 to 10.5 mm) D to in. (9.87 to mm) to in to in. (3.0 to 13.0 mm) B to.026-in. (97.18 to mm) (3.0 to 15.2 mm) to 0.00-in. (3.0 to 10.2 mm) C.027 to.237-in. ( to mm) to in. (3.0 to 9.9 mm) D.238 to.37-in. ( to mm) to 0.01-in. (3.0 to 10.2 mm) E.38 to.571-in. ( to mm) 0.13 to 0.61-in to 0.81-in. (3. to 12.2 mm) A to.812-in. ( to mm) (3. to 15.6 mm) 0.13 to 0.37-in. (3. to 9.5 mm) B.813 to 5.07-in. ( to mm) 0.13 to in. (3. to 9.7 mm) C 5.08 to 5.29-in. ( to mm) 0.13 to 0.13-in. (3. to 10.5 mm) D to 5.72-in. ( to mm) 0.13 to 0.61-in to in. (3. to 9.9 mm) A to in. ( to mm) (3. to 15.6 mm) 0.13 to in. (3. to 8.3 mm) B to in. (16.33 to mm) 0.13 to 0.31-in. (3. to 7.9 mm) C to in. (15.08 to mm) 0.13 to in. (3. to 7.5 mm) D to 5.72-in. ( to mm) 0.13 to 1.35-in to in. (3. to 28.7 mm) A to in. ( to mm) (3. to 3. mm) 0.13 to in. (3. to 27.1 mm) B to in. (16.33 to mm) 0.13 to 1.05-in. (3. to 26.7 mm) C to in. (15.08 to mm) 0.13 to in. (3. to 26.3 mm) D 6.38 to 6.62-in. ( to mm) 0.13 to 0.61-in to 0.37-in. (3. to 9.5 mm) B to in. ( to mm) (3. to 15.6 mm) 0.13 to in. (3. to 5.5 mm) C 7.02 to in. (178.1 to mm) 0.13 to 0.26-in. (3. to 6.2 mm) D to 6.62-in. ( to mm) 0.13 to 1.35-in to 1.11-in. (3. to 28.3 mm) B to in. ( to mm) (3. to 3. mm) 0.13 to in. (3. to 2.3 mm) C 7.02 to in. (178.1 to mm) 0.13 to in. (3. to 25.0 mm) D to 7.62-in. ( to mm) to 0.73-in to 0.99-in. (6. to 12.6 mm) B to in. ( to mm) (6. to 18.5 mm) to 0.37-in. (6. to 9.5 mm) C to 8.00-in. (202.7 to mm) to in. (6. to 7.9 mm) D 8.01 to in. ( to mm) to 0.36-in. (6. to 9.2 mm) E to 7.62-in. ( to mm) to 1.7-in to in. (6. to 31. mm) B to in. ( to mm) (6. to 37.3 mm) to 1.11-in. (6. to 28.3 mm) C to 8.00-in. (202.7 to mm) to in. (6. to 26.7 mm) D 8.01 to in. ( to mm) to 1.10-in. (6. to 28.0 mm) E to in. ( to mm) to 1.70-in to in. (6. to 27.1 mm) A to in. ( to mm) (6. to 37.3 mm) to in. (6. to 27.5 mm) B to in. (22.87 to mm) to in. (6. to 25.7 mm) C to in. (25.53 to mm) to 0.95-in. (6. to 2.0 mm) D to in. ( to mm) to in. (6. to 25.9 mm) E to in. (279.0 to mm) to 1.70-in to in. (6. to 27.9 mm) B to in. ( to mm) (6. to 37.3 mm) to in. (6. to 23.0 mm) C to in. ( to mm) to in. (6. to 29. mm) D 26