Price List. All Prices F.O.B. Plant Issued October 1, 2017 Supersedes March 1, 2017 INDUSTRIAL (ASTM) TANKS

Transcription

1 Price List All Prices F.O.B. Plant Issued October 1, 2017 Supersedes March 1, 2017 INDUSTRIAL (ASTM) TANKS Phone: Fax:

2 INDEX PAGE ORDER INFORMATION PAGE VERTICAL STORAGE TANKS PAGE CAPTOR S/DCT s, CHEMICAL FEED STATIONS, RECTANGULAR CONTAINMENT BASINS, OPEN TOP TANK SYSTEMS & ACCESSORIES, VOTs PAGE HORIZONTAL TANKS & SUPPORTS & PCO TANKS PAGE TOTAL DRAIN TANKS with Plastic Stands PAGE CONE BOTTOM TANKS & STANDS PAGE INTERMEDIATE BULK CONTAINERS (IBC s) PAGE TANK ACCESSORIES Flexmaster, Insulation, Seismic Tie Down Systems, Ladders Gallonage Indicators, External Downpipe Assemblies, Sight Glass Assemblies & Valves, Lateral Restraints, Ultrasonic, Nameplates Internal Downpipe Support Assemblies, PVC & CPVC Piping, Hydrostatic Testing, Hole Cuts Manway and Fill Caps, PVC & CPVC Siphon Tubes, PVC & CPVC U-Vents Flange Adapters, Gaskets PAGE FITTINGS (THREADED) CPVC Fittings, U-Vents w/ BH Fittings, Siphon Tubes w/ BH Fittings PVC, PP & PE Threaded Fittings w/ EPDM or VITON Gaskets Snyder Unitized Molded Outlet -SUMO Fittings & Adapters, Self-Aligning PVC Fittings PAGE FITTINGS (BOLTED) Bolted Double Flanged Fittings (PVC), (SS), (PP) with Stainless Steel Bolts Bolted Double Flanged Fittings (PVC) OR (CPVC) with Stainless Steel, Titanium or Hastelloy Bolts PAGE COMMERCIAL PRICE LISTS Packaging Part No. LIST PRICE GALLONS... $ GALLONS... $ GALLONS... $ (90",102")... $ (120")... $ ,500 (142"& 144 ) See below for 8700 & 10,000 CCS... $ ,500-18,800 (165 ) & 8,700-12,500 CCS (142 ) $1, NOTE: Packaging (protective shrink wrap) not available for tanks shipping out of Washington Court House, OH. 2

3 ORDER INFORMATION APPLICATION REVIEW Chemical Buyer, and user, if different, are solely responsible for making product selection and assuring chemical to be stored is suitable for the use of the product in the application. Capacity: It is recommended that tanks only be filled to their rated capacity, not brimful capacity. Temperature Prevent excessive heat near or inside the tank. Standard polyethylene tanks are designed for a maximum continuous temperature of 100 F / 37.7 C. Pressure Tanks are not pressure vessels and are designed for atmospheric pressure only. Venting venting equipment should be sized to limit pressure or vacuum in the tank to a maximum of ½ water (0.018 psi). Additional precautions may be required if the tank will be filled pneumatically (using air pressure). Failure to provide proper venting will void your warranty. Installation Do not rigidly pipe tanks. Flexible connectors are required at fitting connections to maintain warranty. Consult Snyder s Guidelines for Use and Installation prior to receiving and installing tanks. GENERAL ORDERING INFORMATION FOB Locations: All shipments are FOB factory. L= Lincoln, NE; M= Marked Tree, AR; P=Philippi, West Virginia; C=Chowchilla, CA; W=Washington Court House, OH UPS Orders: All UPS orders ship out of Lincoln, Nebraska Minimum Order: $150. $35 surcharge will be added to all orders under $150. Prices and specifications are subject to change without notice. Dimension may vary +/- 3% (standard rotational molding tolerance) Specify part numbers, tank styles, capacity, materials, color and specific gravity when ordering. Drawing Approvals: For tanks ordered with factory installed fittings supply a marked up Snyder tank drawing showing fitting placement locations. Make sure fittings identified on your PO and marked up drawing match to reduce order processing time. We will generate approval drawings for review and approval (sign off) Supply chemical name, percent concentration, weight (specific gravity or lbs/gal) and temperature. We recommend that all tanks be PROTECTIVE PLASTIC WRAPPED (see page 2 for packaging pricing). Review Snyder order confirmations sent for accuracy of order for both items to be supplied and pricing. Receiving and Inspection: Receiving personnel should inspect tanks and accessories prior to acceptance. Note any damage or missing items on receiving paperwork and immediately notify the appropriate freight carrier. Do not drop tanks off of trucks onto the ground. Refer to Snyder s Guidelines for Use and Installation for proper unloading instructions.

4 SNYDER PART NUMBERS The part numbers listed in the price book each end with two dashes (--) at the end. Use the part number suffix chart below to properly identify the tank being ordered. Using complete part numbers help assure you get the correct tank on your order. *Add the proper code to the end of each tank part number to specify the correct material, color, and specific gravity. SP GR COLOR XLPE HDLPE 1.35 SG NAT SG BLK SG NAT SG NAT SG BLK SG BLK SG Sulfuric HDLPE # SG Opaque HDLPE # PRICING ADDERS Some applications require special resins or pigmented resin that have price adders. Please refer to the chart below to make price adjustment for each application as necessary. ASTM D1998* (1) HDLPE/XLPE No adjustment necessary Black Tanks HDLPE/XLPE Add 10% to pricing Sulfuric Acid*** Sulfuric Resin # Add 15% to HDLPE 1.9 SG pricing for VSTs Add 10% to HDLPE 1.9 SG pricing for Captors & DCTs Sodium Hypochlorite (outdoors)** Opaque White # Add 35% to HDLPE 1.9 SG pricing for VSTs Add 20% to HDLPE 1.9 SG pricing for Captors & DCTs * Does not apply to 15,000 XLPE (1.5 or 1.9 SG ) or 16,500 XLPE (1.5 or 1.9 SG) or HDLPE (1.9 SG) ** Not available on 13,800, 15,000, 16,500 or 18,800 VSTs. These tanks (except for the 16,500) can be used in Sodium Hypochlorite outdoor applications using 1.9 SG HDLPE tanks with 1 insulation. See page 34 for insulation pricing. *** Not available on 16,500 VST (1) ASTM D1998 CERTIFICATION ALL SNYDER INDUSTRIAL VERTICAL SINGLE WALL AND DOUBLE WALL TANKS ARE MANUFACTURED TO MEET ASTM D1998 DESIGN STANDARDS AT 600 PSI HOOP STRESS WHERE APPLICABLE. IF CERTIFICATION IS REQUIRED A HYDROSTATIC WATER TEST AND ASTM DOCUMENTATION MUST BE ORDERED (SEE PAGE 39). THE 13,800 AND 18,800 (165 DIAMETER) TANKS ARE DESIGNED TO ASTM D1998 WALL THICKNESS STANDARDS AT 760 PSI HOOP STRESS. HOWEVER HYDROTESTES ARE NOT AVAILABLE FOR THESE TANKS AND THEY CANNOT BE CERTIFIED TO ASTM D1998.

5 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N L " $259 $ N C " $384 $ N M " $267 $ N C " $397 $ N M,L,C " $330 $ N L " N/A $ N C " $528 $ N L " $528 $ N M " $572 $ N P " $684 $ N M " $684 $ N C " $666 $ N L,M " $708 $ N C " $642 $ N L " $642 $ N P " $708 $ N L,M " $708 $ N L " $679 $ N C " $943 $ N C " $756 $622 Black and Opaque White and XLPE FOB Marked Tree, Arkansas Only. 5

6 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N L " $794 $ N M " $878 $ N L " $830 $ N C " $794 $ N P " $878 $ N C " 0.02 $916 $ N M " $962 $ N M " 0.02 $1,110 $ N P " 0.02 $1,124 $ N L " 0.03 $1,124 $ N C " $1,124 $ N M " $1,124 $ N M " $1,124 $ N M " $1,085 $ N C " 0.02 $1,087 $ N P " 0.02 $1,115 $ N M " $1,129 $1, N C " $1,141 $1, N M " 0.02 $1,209 $1, N L " $1,148 $1, N M " $1,464 $1, N M " $1,621 $1, N C " $1,370 $ N L,M,P " $1,370 $918 6

7 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N L,C " $1,100 $ N M,P " $1,100 $ N C " $2,213 $2, N L,M,P " 0.05 $2,185 $2, N C " $1,783 $1, N C " $2,544 $1, N L,M,P " 0.1 N/A $1, N L,M,P " 0.1 $2,150 $1, N L,P,C " $1,947 $1, N M " $1,947 $1, N C " $2,256 $1, N C " $3,334 $1, N C " 0.1 $2,721 $2, N C " 0.1 $4,117 $2, N C " 0.2 $2,729 $2, N C " 0.2 $4,126 $2, N L,P,C " 0.1 $2,135 $1, N M " 0.01 $2,134 $1, N L,M,P " 0.2 N/A $2, N L,M,P " 0.2 $3,220 $2, N C " 0.2 $3,800 $2, N C " 0.2 $5,479 $3, N P " 0.25 $3,800 $2, N P " 0.25 $5,479 $3,422 7

8 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N L,P " N/A $2, N L,P " $3,286 $2, N L,P " $4,645 $2, N C " N/A $2, N C " $3,286 $2, N C " $4,645 $2, N M " N/A $2, N M " $3,286 $2, N M " $4,645 $2, N L,P " N/A $2, N L,P " $4,016 $2, N L,P " $4,840 $3, N M " N/A $2, N M " $4,016 $2, N M " $4,840 $3, N C " N/A $2, N C " $4,016 $2, N C " $4,840 $3, N M " $4,216 $2, N M " $5,083 $3, N L,P " 0.2 N/A $3, N L,P " 0.2 $5,335 $4, N L,P " 0.2 $6,726 $5, N C " Flatbed N/A $3, N C " Flatbed $5,335 $4, N C " Flatbed $6,726 $5,352 8

9 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N M " 0.2 N/A $3, N M " 0.2 $5,335 $4, N M " 0.2 $6,726 $5, N L,P,C " N/A $3, N L,P,C " $4,518 $3, N L,P,C " $6,410 $4, N M " Flatbed $7,302 $6, N M " Flatbed $9,836 $7, N L " 0.25 $7,869 $6, N L " 0.25 $9,748 $8, N C " Wide $7,929 $6, N C " Wide $9,435 $8, N P " Flatbed $7,302 $6, N P " Flatbed $9,458 $7, N M " Wide $7,929 $6, N M " Wide $9,435 $7, N L " 0.28 $10,660 $8, N L " 0.28 $12,745 $11, N L,C " Flatbed $8,987 $6, N L,C " Flatbed $11,078 $7, N C " Wide $8,549 $7, N C " Wide $10,058 $8, N C " Wide $12,016 $9, N C " Wide $9,010 $8, N C " Wide $10,362 $10,037 = sumo not available on this tank. 9

10 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N M " Flatbed $10,010 $8, N M " Flatbed $12,184 $10, N L " Flatbed $13,659 $10, N L " Flatbed $16,310 $12, N P " Flatbed $10,010 $8, N P " Flatbed $12,184 $10, N L " Flatbed $15,366 $11, N L " Flatbed $18,435 $12, N L,P " Wide $9,586 $8, N L,P " Wide $10,847 $10, N P " Wide $10,058 $7, N P " Wide $12,016 $10, N C " Wide $10,844 $8, N C " Wide $12,801 $11, N L,P,C " Flatbed N/A $8, N L,P,C " Flatbed $12,238 $10, N L,P,C " Flatbed $15,215 $12, N M " Wide N/A $8, N M " Wide $11,070 $9, N M " Wide $13,534 $12, N L,P " Wide N/A $8, N L,P " Wide $12,116 $9, N L,P " Wide $14,184 $12, N C " Wide $12,117 $9, N C " Wide $14,184 $12, N L " Wide $10,702 $10, N L " Wide $14,229 $13, N L " Flatbed $21,854 $18, N L " Flatbed $28,226 $25,467 = sumo not available on this tank. 10

11 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N L " Wide $20,356 $13, N L " Wide $21,015 $17, N C " Wide $19,044 $14, N C " Wide $22,403 $20, N L " Wide $21,203 $14, N L " Wide $26,525 $19, N L " Wide $14,369 $13, N L " Wide $19,180 $18, N L " Wide $21,854 $18, N L " Wide $27,672 $25, N-- 10, L,P " Wide $16,651 $13, N-- 10, L,P " Wide $20,868 $15, N-- 10, L,P " Wide $25,026 $21, N-- 10,500 10,500 C " Wide $16,650 $13, N-- 10,500 10,500 C " Wide $20,869 $15, N-- 10,500 10,500 C " Wide $25,026 $21, N-- 12,500 12,750 L " Wide N/A $19, N-- 12,500 12,750 L " Wide $24,339 $20, N-- 12,500 12,750 L " Wide $31,103 $26,546 NEW N-- 13,800 15,000 W " Wide N/A $22,253 ** NEW N-- 13,800 15,000 W " Wide N/A $26,393 ** NEW N-- 13,800 15,000 W " Wide N/A $29,808 ** ** Meets ASTM D1998 wall thickness standards (760 psi hoop stress). No hydrotest available/cannot be certified ASTM D

12 VERTICAL STORAGE TANKS Tank Tank Tank Cylinder Tank % of Snyder Capacity Brimful Diameter Height Height Specific Manway 53' XLPE HDLPE Part No. (Gallons) Capacity F.O.B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink Linear N-- 15,000 15,250 L " Wide N/A $22, N-- 15,000 15,250 L " Wide $33,733 * $26, N-- 15,000 15,250 L " Wide $42,876 * $29, N-- 16,500 16,800 L " Wide N/A $29, N-- 16,500 16,800 L " Wide $41,473 * $35, N-- 16,500 16,800 L " Wide $56,275 * $39,744 * NEW N-- 18,800 20,000 W " Wide N/A $29,498 ** NEW N-- 18,800 20,000 W " Wide N/A $35,190 ** NEW N-- 18,800 20,000 W " Wide N/A $39,744 ** * = does not meet ASTM standards. ** Meets ASTM D1998 wall thickness standards (760 psi hoop stress). No hydrotest available/cannot be certified ASTM D1998. Tank Saver Platform System (TSPS) Tank Platform Only L 102" Available in Grey only $4, Cable System for above L $ Ladder attachement for base L $104 12

13 CAPTOR CONTAINMENT SYSTEMS (CCS) Tank Nominal Tank Tank % of SUGGESTED LIST Snyder Tank Capacity Tank Height Specific Manway 53' XLPE HDLPE Part No. Style (Gallons) F.O.B. Diameter (") (Inches) Gravity Fill Truck Crosslink Linear N-- CCS 550 L " $5,113 $4, N-- CCS 1100 L $7,115 $5, N-- CCS 1550 L $7,512 $6, N-- CCS 2000 L,P FLATBED $9,276 $8, N-- CCS 2500 L,P FLATBED $10,822 $10, N-- CCS 3000 L,P FLATBED $11,947 $11,477 ** N-- CCS 3000 L,P FLATBED $14,477 $13, N-- CCS 3500 L,P FLATBED $14,946 $14, N-- CCS 3500 L,P FLATBED $16,938 $16, N-- CCS 4000 L,P FLATBED $18,032 $17, N-- CCS 4000 L,P FLATBED $21,687 $19, N-- CCS 4500 L FLATBED $21,719 $20, N-- CCS 4500 L FLATBED $24,336 $22, N-- CCS 5000 L FLATBED $25,158 $24, N-- CCS 5000 L FLATBED $28,048 $26, N-- CCS 5500 L WIDE $22,066 $21, N-- CCS 5500 L WIDE $25,212 $23, N-- CCS 6500 L WIDE $28,110 $27, N-- CCS 6500 L WIDE $30,780 $29, N-- CCS 8700 L " WIDE $39,202 $32, N-- CCS 8700 L " WIDE $42,924 $35, N-- CCS 10,000 L " WIDE $52,905 $45, N-- CCS 10,000 L " WIDE $62,346 $50, N-- CCS 12,500 L " WIDE $66,948 $58, N-- CCS 12,500 L " WIDE Not Available $64,395 NOTE: See page 16 for double wall tanks from Gallons. Note: all primary tanks have specific gravity and material listed, with secondary outer containment manufactured from HDLPE/Nat/1.5 and includes a standard 18" threaded manway (Note exceptions). Note: gallon CCS have a standard secondary outer containment manufactured from HDLPE/Nat/1.9 gravity. ** Note: The 3000 gallon CCS in 1.9 specific gravity has a secondary outer containment in 1.9/HDLPE/Nat included in the price. Upcharge for secondary outer HDPE/Natural/1.9 = Add 12% XLPE/Natural/1.9 = Add 40% containment made of: XLPE/Natural/1.5 = Add 25% Black Primary - Add 10% Black Both Tanks - Add 15% Upcharge for Sulfuric Acid Resin #880046: HDPE/Natural/1.9 = Add 10% (for the primary tank) Upcharge for Sodium Hypochlorite opaque white Resin #880059: HDPE/Natural/1.9 = Add 20% (for the primary tank) *XLPE Containment not available for 8700 CCS and larger. 1.9 S.G. containments not available for 5000, 10,000, and 12,500 CCS. 13

14 CAPTOR CONTAINMENT SYSTEM ACCESSORIES UFO (Unified Fitting Outlet) Assembly - **DOES NOT INCLUDE FITTING** design allows BOLTED side wall fittings to be installed and sealed through both walls of the CCS (fittings on pages 50-55). Snyder Suggested Part No. Fitting Gasket List N--2E Transition for 2" bolted ftg. - EPDM $ N--3E Transition for 3" bolted ftg. - EPDM $ N--4E Transition for 4" bolted ftg. - EPDM $566 * N--6E Transition for 6" bolted ftg. - EPDM $793 Snyder Suggested Part No. Fitting Gasket List N--2V Transition for 2" bolted fitting - VITON $ N--3V Transition for 3" bolted fitting - VITON $ N--4V Transition for 4" bolted fitting - VITON $915 * N--6V Transition for 6" bolted fitting - VITON $1,560 You must ADD the required size bolted fitting in conjunction with the UFO to arrive at the assembly price. THREADED BULKHEAD FITTINGS CANNOT BE USED WITH THE UFO FITTING ARRANGEMENT. * 6" UFO only available on tanks 120" diameter and larger. ADDITIONAL ACCESSORIES UFO fitting locations are: 0, 90, 180, and 270 only. Snyder Suggested Part No. Description List Leak Detection Sensor - Can be used on all Captors and on DCTs gallons. $ Leak Detection Sensor - for 12,500 gallon Captor only. $ Ultrasonic Level Indicator includes fitting. For tanks 79" or taller only. $3, Ultrasonic Level Indicator includes fitting. For tanks 78" or shorter only. $3,215 Snyder Suggested Part No. Seismic Restraints List gal., Galv. Steel* $1, gal., Galv. Steel* $2, ,000 gal. Galv. Steel* $2, ,500 gal. Galv.Steel* $4,375 *Call for pricing on 304 & 316 Stainless Steel seismic systems. **Call for pricing on Heat Trace. CAPTOR CONTAINMENT SYSTEM ACCESSORIES 14

15 CAPTOR CONTAINMENT SYSTEM ACCESSORIES Snyder Part No. Suggested Suggested EPDM VITON Sight Glass Assemblies List-EPDM List-VITON Captor Sight Glass Assy with PVC Tee- 2" $242 $ Captor Sight Glass Assy with CPVC Tee- 2" $ Captor Sight Glass Assy with PVC Tee- 3" $353 $ Captor Sight Glass Assy with CPVC Tee- 3" $ Captor Sight Glass Assy with PVC Tee- 4" (EPDM) $ Captor Sight Glass Assy with CPVC Tee- 4" (EPDM) $764 Sight Glass assemblies to be used with UFO fitting assembly Reverse Float Indicators (PVC/PP) - HDLPE Tanks Only Captors $2, ,000 Captors $3,287 12,500-13,700 Captors $3,532 Adder for Sulfuric $ Reverse Stenciled Calibration Board (optional) $488 CAPTOR: External Fill Pipe Assemblies - Ground Supported FOR CAPTOR CONTAINMENT SYSTEMS - but can be used on VST's (does not include fitting) Snyder Part No. List Price List Price PVC CPVC Description PVC CPVC " External Fill Pipe Assembly $654 $ " External Fill Pipe Assembly $1,205 $1, " External Fill Pipe Assembly $1,374 $2, " Valve/Elbow Assy for External Fill Assy- PVC, PP $213 $ " Valve/Elbow Assy for External Fill Assy - PVC, PP $514 $696 15

16 October 1, 2017 DUAL CONTAINMENT TANKS (DCT) NEW Snyder Part No N N N N N N N N N N-- Tank Style DCT DCT w/pump recess DCT DCT w/pump recess DCT DCT DCT DCT DCT DCT Tank Capacity (Gallons) F.O.B. M M M M M M M M M L Nominal Tank Diameter (") Tank Height (Inches) Tank Specific Gravity Manway Fill 6" 6" 14" 6" 14" 14" 18" 18" 18" 18" % of 53' Truck SUGGESTED LIST XLPE HDLPE Crosslink Linear $665 $484 $664 $484 $787 $627 $788 $627 $1,333 $1,000 $1,510 $1,027 $2,229 $1,455 $2,638 $1,555 $3,571 $1,830 $4,732 $3,043 Note: For DCT sidewall outlets, use a bolted double flanged fitting or a PVC, CPVC, or PP bulkhead fitting. An extra gasket of appropriate material (page 43) is also required. Sidewall fitting locations at 0, 90, 180, and 270 only. Exception 1000 DCT which is limited to 2 outlets within 90 of each other. Note: all primary tanks have specific gravity and material listed, with secondary outer containment manufactured from HDLPE/1.9/Nat. Upcharge for secondary outer containment made of: Upcharge for Sulfuric Acid Resin #880046: Upcharge for Sodium Hypochlorite opaque white Resin #880059: Snyder Part No XLPE/Natural/1.9 = Add 40% Black Primary - Add 10% Black Both Tanks - Add 15% HDPE/Natural/1.9 = Add 10% (for the primary tank) HDPE/Natural/1.9 = Add 20% (for the primary tank) Seismic Restraints DCT Seismic Restraint System Gal. DCT LIST PRICE HDLPE $1, Snyder Part No DCT LIQUID LEVEL GAUGE 35 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 60 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 120 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 150 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 275 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 360 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 500 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC 1000 Gallon DCT Level Gauge - hinged float, Kynar/PE/PVC LIST PRICE HDLPE $585 $597 $608 $615 $619 $619 $657 $657 Snyder Part No DCT LIQUID DRAW TUBE 1.5"/2" DCT Draw Tube Assy, EPDM 1.5"/2" DCT Draw Tube Assy, VITON LIST PRICE HDLPE $177 $ Note: Assembly consists of HDPE float, Kynar rods, PVC bushing & Gauge guard. Note: 2" THREADED Fitting required for installation (not included in pricing). Note: Consult factory for fitting placement to ensure freedom of movement of hinged mechanism. Note: Assembly consists of 1.5" PP draw tube, 2" PP 90 elbow & 2" PP male camlock adapter & cap. Note: 2" Threaded fitting required for installation (not incluced in pricing). Note: If ordering without a DCT specify size of tank for draw tube length.

17 CHEMICAL FEED STATIONS Snyder Tank Capacity Overall Tank Overall Specific % OF 53 XLPE HDLPE Part No. Style Gallons F.O.B. Overall Width Length Height Gravity Manway Fill Truck Crosslink Linear CF-- CFS 35 M " $746 $ CFWS-- CFS w/stand 35 M " $1,212 $1, CF-- CFS 60 M " $809 $ CFWS-- CFS w/stand 60 M " $1,276 $1, CF-- CFS 90 M " $1,207 $1, CFWS-- CFS w/stand 90 M " $1,912 $1, CF-- CFS 120 M " $1,344 $1, CFWS-- CFS w/stand 120 M " $2,050 $1, CF-- CFS 150 M " $1,373 $1, CFWS-- CFS w/stand 150 M " $2,078 $1, CF-- CFS 200 M " $1,767 $1, CFWS-- CFS w/stand 200 M " $2,616 $2, CF-- CFS 250 M " $1,901 $1, CFWS-- CFS w/stand 250 M " $2,750 $2, CF-- CFS 275 M " $2,052 $1, CFWS-- CFS w/stand 275 M " $3,041 $2, CF-- CFS 330 M " $2,070 $1, CFWS-- CFS w/stand 330 M " $3,059 $2, CF-- CFS 440 M " $2,773 $2, CFWS-- CFS w/stand " $3,950 $3,704 M * Price includes Tank, Rectangular Containment Basin (black color) and Pump Shelf. All fitting accessories are priced separately. * The pump shelf on the 200 to 330 gallon size are two corner triangular shaped shelves. All other sizes have pump shelves full across the end of the containment. * XLPE systems have XLPE tank and HDLPE rectangular containment basin. * Stands are 12" Height - HDLPE polyethylene (red color). Chemical Feed Station assemblies include protective wrap packaging for shipment. Suggested List 17

18 CHEMICAL INJECTION TANK SYSTEMS Snyder Tank Capacity Overall Overall Overall Specific Manway % of 53' Part No. Style Gallon F.O.B. Width Length Height Gravity Fill Truck XLPE HDLPE CITS-- CITS 65 M " $958 $ CITS-- CITS 125 M " $1,125 $1, CITS-- CITS 225 M " 0.03 $1,525 $1, CITS-- CITS 335 M " $1,937 $1,753 * Price includes Tank, Rectangular Containment Basin (Black HDPE) and Stand (Black HDPE). Fittings & Accessories priced separately. * XLPE systems have XLPE tank and HDLPE containment basin and stands. * stands have molded-in metal inserts for attaching banding and pumps. Snyder Part No. Item Fits Tank Size F.O.B. List Price Bands 65 M $ Bands 125 M $ Bands 225 M $ Bands 335 M $168 * Band Assemblies include (2) SS bands and (4) 3/8" SS hex head bolts and washers USED OIL COLLECTION TANKS (UOCT) Tank Capacity (gallons) Tank Specific Gravity Nominal Tank Tank Height % of 53' Snyder Part No. Tank Style F.O.B. Diameter (") (Inches) Manway Fill Truck N95703 UOCT 120 M " hinged $1, N95703 UOCT 150 M " hinged $1, N95703 UOCT 275 M " hinged $2, N95703 UOCT 360 M " hinged $2, N95703 UOCT 500 M " hinged $3,082 NEW! N95703 UOCT 1000 L " hinged $3,811 * UOCT's consist of a black primary storage tank, a Safety Yellow Containment tank with "Used Oil Only" stenciled in black on the front, Hinged lockable manway with 1" deep strainer basket and 2" bulkhead fitting on top with 1.5" internal draw tube assembly with 2" external male camlock connection. 275, 360 & 500 gallon models have fork-lift access bases. LIST PRICE HDLPE Linear Optional Level Gauges (price includes 2" fitting # ) Part # LIST PRICE Assembly consists of HDPE float, galvanized rod, and bushing Fits 120 UOCT $ Fits 150 UOCT $ Fits 275 UOCT $ Fits 360 UOCT $ Fits 500 UOCT $ Fits 1000 UOCT $386 18

19 RECTANGULAR CONTAINMENT BASINS Tank Tank Tank Tank Maximum HDLPE HDLPE Capacity Width Length Height Specific Tank % OF 53' WITHOUT WITH Snyder Part No. Gallons F.O.B. (inches) (inches) (inches Gravity Diameter TRUCK PUMP SHELF PUMP SHELF N-- 90 M $319 $ N M $690 NA N M $426 $ N M $920 NA N C $920 NA N M $978 NA N M $605 $ N M $916 $1, N M $834 NA N M $942 NA N L $1,141 NA * Containment basins are supplied in HDLPE in black color OPEN TOP TANKS (VOT) Open Top Tanks are ideal for secondary containments. Snyder Part No. Tank Style Tank Capacity (Gallons) F.O.B. Tank Diameter (inches) Tank Height (inches) 1.35 XLPE HDLPE N-- VOT 175 C $709 N/A N/A $618 NA NA N-- VOT 290 C $918 N/A N/A $794 NA $ N-- VOT 345 C $1,046 N/A N/A $947 NA $1, N-- VOT 650 C $1,866 N/A N/A $1,615 NA $2, N-- VOT 700 L NA N/A $1,962 NA NA $1,658 Note: All VOT tank systems have an inward lip flange at tank opening. Not to be used with heat traced and insulated tanks. 19

20 OPEN TOP TANKS (VOT) Open Top Tanks are ideal for secondary containments. Snyder Part No. Tank Style Tank Capacity (Gallons) F.O.B. Tank Diameter (inches) Tank Height (inches) 1.35 XLPE HDLPE N-- VOT 775 C $2,061 N/A N/A $1,658 N/A $2, N-- VOT 975 C $2,243 N/A N/A $1,893 N/A $2, N-- VOT 1000 L N/A $2,662 $3,303 N/A $2,297 $2, N-- VOT 1250 P N/A $2,662 $3,303 N/A $2,388 $2, N-- VOT 1350 C $2,683 N/A N/A $2,312 N/A $2, N-- VOT 1450 C $2,842 N/A N/A $2,579 N/A $2, N-- VOT 1550 C $2,866 N/A N/A $2,691 N/A $3, N-- VOT 1800 P N/A $3,216 $4,016 N/A $2,997 $3, N-- VOT 1850 C $3,258 N/A N/A $2,833 N/A $3, N-- VOT 1900 C $3,082 N/A N/A $2,751 N/A $3, N-- VOT 2500 P N/A $4,965 $6,211 N/A $4,374 $5, N-- VOT 2500 C $4,780 N/A N/A $4,206 N/A $4, N-- VOT 2850 C $5,297 N/A N/A $4,657 N/A $6, N-- VOT 3000 C $4,280 N/A N/A $3,865 N/A $4, N-- VOT 3600 P N/A $6,481 $8,268 N/A $5,846 $7, N-- VOT 4000 C $5,965 N/A N/A $5,011 N/A $7, N-- VOT 4900 C $6,803 N/A N/A $6,408 N/A $9, N-- VOT 5800 L N/A $10,707 $13,079 N/A $9,880 $12, N-- VOT 6100 C $10,707 N/A N/A $9,784 N/A $14, N-- VOT 6900 L N/A $12,013 $15,962 N/A $11,249 $13,912 Note: All VOT tank systems have an inward lip flange at tank opening. Not to be used with heat traced and insulated tanks. 20

21 OPEN TOP TANK SYSTEMS PRICE INCLUDES COVER ONLY, PLASTIC STANDS OPTIONAL - STANDS PRICED ON PAGE 22 Tank Nominal Tank & Lid Nominal Tank SUGGESTED SUGGESTED Snyder Tank Capacity Tank Overall Height Specific LIST LIST Part No. Style (Gallons) F.O.B. Diameter(") Diameter (") (Inches) Gravity Lid XLPE HDLPE Linear * 10001VOT-- VOT 30 L,M " $229 $188 * 56800VOT-- VOT 55 C,L,M " $287 $237 * 56900VOT-- VOT 90 M " $450 $370 * 57000VOT-- VOT 120 C,L,M " $575 $473 * 57100VOT-- VOT 150 C,L,M " $661 $544 * 57200VOT-- VOT 200 C,M " $774 $638 * 57300VOT-- VOT 250 M " $868 $716 * 57400VOT-- VOT 275 C,M " $999 $823 * 57500VOT-- VOT 330 M " $1,202 $990 * 57600VOT-- VOT 360 C,M " $1,202 $990 * 57700VOT-- VOT 440 M " $1,654 $1,363 * 57800VOT-- VOT 500 C,M " $1,805 $1,487 *XLPE, Black, and Opaque White available FOB Marked Tree, AR. OPEN TOP TANKS SYSTEMS - TOTAL DRAIN PRICE INCLUDES STANDARD COVER, DOES NOT INCLUDE STAND PRICE, WHICH IS REQUIRED -stands are priced on page 22 Tank Nominal Overall Overall Tank Overall SUGGESTED Snyder Tank Capacity Diameter Height Height Specific Diameter LIST Part No. Style (Gallons) F.O.B. (Inches) w/12" stand w/18" stand Gravity w/stand (") HDLPE Linear 568TDVOT-- CB15VOT 55 L /2 $ TDVOT-- CB15VOT 90 L /2 $ TDVOT-- CB15VOT 120 L /2 $ TDVOT-- CB15VOT 150 L /2 $ TDVOT-- CB15VOT 200 L /2 $ TDVOT-- CB15VOT 250 L /2 $985 Total Drain tanks not available in XLPE. All Total Drain tanks must be ordered with stands listed on page 22 - NO EXCEPTIONS. Packaging included on tank products listed on this page. When stand ordered with tank - both will be wrapped as one piece 21

22 OPEN TOP TANKS SYSTEMS - TOTAL DRAIN PRICE INCLUDES STANDARD COVER ONLY - PLASTIC STANDS OPTIONAL - stands are priced on page 22 Tank Nominal Overall Overall Overall Overall SUGGESTED Snyder Tank Capacity Diameter Height Height Height Diameter LIST Part No. Style (Gallons) F.O.B. (Inches) (Inches) w/12" stand w/18" stand w/stand (") HDLPE Linear 574TDVOT-- CB15VOT 275 L /2 $1, TDVOT-- CB15VOT 330 L /2 $1, TDVOT-- CB15VOT 360 L /2 $1, TDVOT-- CB15VOT 440 L /2 $1, TDVOT-- CB15VOT 500 L /2 $1,771 Total Drain tanks not available in XLPE. All Total Drain tanks must be ordered with stands listed below - NO EXCEPTIONS. Packaging included on tank products listed on this page. When stand ordered with tank - both will be wrapped as one piece TANK STANDS REQUIRED ON OPEN TOP TOTAL DRAIN TANKS Nominal LIST PRICE Snyder Nominal Bottom HDLPE Part No. Stand F.O.B. Diameter Clearance Linear N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $985 Patent # N " Dia. L,M $ N " Dia. L,M $1, N " Dia. L,M $1, N " Dia. C,L,M $1,367 *Tank Stands can also be utilized with closed top tanks in diameters up to 48" Packaging included on tank products listed on this page. When stand ordered with tank - both will be wrapped as one piece 22

23 OPEN TOP TANK SYSTEMS COVERS HINGED Must be ordered at same time as tank Snyder LIST PRICE LIST PRICE Part No. Description XLPE HDLPE F.O.B N-- Hinged Lid Assembly for 90, 120, 150 VOTs $390 $278 M N-- Hinged Lid Assembly for 200 & 250 VOTs $515 $368 M N-- Hinged Lid Assembly for 275 & 330 VOTs $682 $488 M N-- Hinged Lid Assembly for 360, 440 & 500 VOTs $850 $608 M Sulfuric Acid add - 15%. Opaque white - Add 35%. BOLTED & SEALED Snyder SUGGESTED Part No. Description LIST F.O.B Bolted & Sealed Lid Assembly for 55 VOT $207 M Bolted & Sealed Lid Assembly for 90, 120 & 150 VOTs $276 M Bolted & Sealed Lid Assembly for 200 & 250 VOTs $353 M Bolted & Sealed Lid Assembly for 275 & 330 VOTs $840 M Bolted & Sealed Lid Assembly for 360, 440, & 500 VOTs $902 M PLASTIC STAND ACCESSORIES - Closed Top Tanks (Page 27) and Open Top Tanks (Page 21). Snyder **Strapping must be factory installed** SUGGESTED Part No. Description LIST Tie-down strapping - 22" Stand $ Tie-down strapping - 30" Stand $ Tie-down strapping - 36" Stand $ Tie-down strapping - 42" Stand $ Tie-down strapping - 48" Stand $136 23

24 Mixer Mounts Snyder SUGGESTED Part No. Description LIST Mixer Mount Assembly for open/closed top tanks (Maximum mixer weight of 150 lbs.) $860 Must use with Sii Plastic Stand only. Not available for use with Gallon tanks. TOTAL DRAIN FITTINGS & Vents Snyder SUGGESTED Part No. Description LIST " PP BF200 Bolted Drain w/epdm $ " PP BF200 Bolted Drain w/epdm $ " PP BF200 Bolted Drain w/viton $ " PP BF200 Bolted Drain w/viton $ /2" Welded HDPE Female NPT Thread $ /4" Welded HDPE Female NPT Thread $ " Welded HDPE Female NPT Thread $ /2" Welded HDPE Female NPT Thread $ " Welded HDPE Female NPT Thread $ " Welded HDPE Female NPT Thread $ " Threaded Vent - does not include fitting $ " Threaded Vent with Mesh Screen - does not include fitting $ " Threaded Vent - does not include fitting $ " Threaded Vent with Mesh Screen - does not include fitting $71 Welded fitting available on open top tanks only - Fittings can only be placed on the bottom of these tanks. 24

25 October 1, 2017 HORIZONTAL TANKS (HLT) Snyder Part No N N N N N N N N N N N N N N--T N N--T N--T N N--T N N--T N--T N--T Tank Style HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT HLT Tank Capacity (Gallons) Tank Tank Diameter Length F.O.B. L,P,M,C L,P,C M M L,P,C M L,P,C L,P C M C L,P M L,P,C L L,P,C M,C L P,C L L,P,M,C L,P,M,C L Tank Height (Inches) (Inches) (Inches) XLPE, Black & opaque - F.O.B. Lincoln, & Philippi only. The hoop assemblies are required and included in the above prices on 730 gallons and above. NOTE: Only (1) hoop supplied and only available in HDLPE, Natural color. NOTE: Opaque white Sodium Hypochlorite resin # and Sulfuric Acid resin # are not available on HLT's above 525 gallons. 25 Tank Specific Manway Gravity Fill 1.9 6" 1.9 6" 1.9 6" 1.9 6" " 1.9 6" " " " 1.9 6" " " " " " " " " " " " " % of SUGGESTED LIST 53' XLPE HDLPE Truck Crosslink Linear N/A $ $372 $ $373 $ $539 $ $539 $ $679 $ $680 $ $967 $ $967 $ $966 $ $1,317 $1, $1,317 $1, $1,317 $1, N/A $2, N/A $2, N/A $3, N/A $6, N/A $5, N/A $6, N/A $9, $11,513 $9, $11,702 $10, N/A $15,454 T= tank mold is transferred from plant to plant. Availability/lead time at plants dependent on available stock and mold location.

26 HORIZONTAL TANK BANDS, HOOP ASSEMBLIES Note: Hoop Assemblies required for tanks 730 gallons and above and included in tank pricing. Stainless Tank List Steel Bands Style Tank Size Available Price-ea. POLY STANDS FOR HLTS (65, 125, 225 & 335 GALLONS) HLT 30 gallon L,M,P,C $67 Part No. Stand for HLT Height F.O.B. List Price HLT 60 gallon L,M,P,C $ N97802 Poly Stand for 65 HLT # N-- 32 M $ HLT 125 gallon L,P,C $ N97802 Poly Stand for 125 HLT # N-- 32 M $ HLT 230 gallon L,P,C $ N97802 Poly Stand for 225 HLT # N-- 30 M $ HLT 300 gallon L,M,P $ N97802 Poly Stand for 335 HLT # N-- 35 M $ HLT 525 gallon L,M,P $94 *Same stand is used for the 65 and 125 HLT HLT 730 gallon L,M $ J-Bolt Pkg. $37 Note: Stainless Steel Bands (optional) - 2 bands plus (1) J-bolt package needed per tank HOOP ASSEMBLY - 2 hoop assembly unless noted. Galvanized Tank Tank Size List Hoop Assembly Style Size F.O.B Price HLT 300 gallon C $ HLT 500 gallon C $ HLT 525 gallon L,P,M $ HLT 730 gallon L,M,C $174 each RECTANGULAR (PCO) TANKS Tank Tank Overall Overall Tank List Snyder Tank Capacity Length Width Height Specific Manway HDLPE Part No. Style (Gallons) Available (Inches) (Inches) (Inches) Gravity Fill Linear N--43 PCO 30 L,P,C " $ N--43 PCO 50 L,P,C " $ N--43 PCO 100 L,P,C $ N--43 PCO 150 L,P,C $ N--43 PCO 200 L,P,C $ N--43 PCO 325 C " $1,255 Note: For mobile applications banding or straps are required. These are not currently offered by Snyder Industries. 26

27 October 1, 2017 TOTAL DRAIN TANKS WITH PLASTIC STANDS Closed Top Tanks All Total Drain tanks must be ordered with stands listed on page 28. NO EXCEPTIONS TANKS HDPE, NATURAL TANKS Tank Snyder Tank Capacity Part No. Style (Gallons) N-- CB15VCT 60 Gallon N-- CB15VCT 90 Gallon N-- CB15VCT 120 Gallon N-- CB15VCT 150 Gallon N-- CB15VCT 200 Gallon N-- CB15VCT 250 Gallon N-- CB15VCT 275 Gallon N-- CB15VCT 330 Gallon N-- CB15VCT 360 Gallon N-- CB15VCT 440 Gallon N-- CB15VCT 500 Gallon N-- CB15VCT 550 Gallon N-- CB15VCT 850 Gallon Nominal Overall Dia. Dia. F.O.B. (Inches) (Inches) L L L L L L L L L L L L L Available with 12" stand only. Note: All tanks above rated 1.9 specific gravity. Exceptions: Height (Inches) Top Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Flat Domed Domed Lid 14" 14" 14" 14" 14" 14" 18" 18" 18" 18" 18" 18" 18" O.D SUGGESTED LIST 12" Ht. 18" Ht. HDLPE $ $ $ $ $ $ $1, $1, $1, $1, $1, $1, N/A $2,636 Total Drain tanks not available in XLPE. 850 gallon is limited to 1.1 specific gravity in standard weight 12" stand. 550 is limited to 1.7 specific gravity. 27

28 STANDS (Required on Tanks listed on page 27) Nominal Nominal SUGGESTED Snyder Diameter Bottom LIST Part No. Stand Available (Inches) Clearance(") HDLPE N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L,M $ N " Dia. L $ N " Dia. L,M $ N " Dia. L $1, N " Dia. L $1,189 Patent # N " Dia. C,L $1,367 28

29 CONE BOTTOM TANKS (CBT) Tank Tank Tank F. Tank Height Height Tank % of Snyder Style/ Capacity O. Diameter w/o Stand w/stand Specific Manway 53' XLPE HDLPE Part No. Degree (Gallons) B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink** Linear N-- CBT L " N/A $ N-- CBT L " N/A $ N-- CBT L " N/A $ N-- CBT L " N/A $ N-- CBT L " N/A $570 * N-- CBT C " N/A $1,358 * N-- CBT C " N/A $2, N-- CBT L " 0.1 $1,493 $1, N-- CBT L " $2,417 $1, N--T CBT L " $2,417 $1, N--T CBT M " 0.14 $2,722 $1, N--T CBT L " $2,722 $1, N-- CBT L " 0.21 $3,160 $2, N--T CBT M " 0.14 $4,069 $2, N--T CBT L " $4,068 $2, N-- CBT L " $3,162 $2, N-- CBT L " $4,050 $3, N--T CBT M " 0.33 $3,754 $2, N--T CBT M " 0.33 $4,575 $4,331 T= tank mold is transferred from plant to plant. Availability/lead time at plants are dependent on available stock and mold location. *Tanks come complete with polyethylene stands only. Tank Snyder recommends cone bottom tank applications DO NOT EXCEED 100º F. Note: Cone Bottom tanks are not ASTM D1998 design. Issued 29

30 CONE BOTTOM TANKS (CBT) Tank Tank Tank Tank F. Tank Height Height Tank % of Snyder Style/ Capacity O. Diameter w/o Stand w/stand Specific Manway 53' XLPE HDLPE Part No. Degree (Gallons) B. (Inches) (Inches) (Inches) Gravity Fill Truck Crosslink** Linear N--T CBT L " 0.2 $3,789 $2, N--T CBT L " 0.2 $4,619 $4, N-- CBT L " 0.25 $5,029 $4, N-- CBT L " 0.25 $5,741 $4, N--T CBT M " 0.33 $4,949 $3, N--T CBT M " 0.33 $5,879 $4, N--T CBT L " 0.25 $4,949 $3, N--T CBT L " 0.25 $5,879 $4, N-- CBT L " 0.29 $7,578 $6, N-- CBT L " 0.29 $8,730 $7, N-- CBT L " 0.33 $8,934 $7, N-- CBT L " 0.33 $10,304 $9, N-- CBT L " 0.33 $11,472 $8, N-- CBT L " 0.33 $13,240 $10, N-- CBT L " 0.37 $15,815 $12, N-- CBT L " 0.37 $17,230 $14, N-- CBT L " Wide $13,485 $10, N-- CBT L " Wide $16,391 $13, N-- CBT L " 0.45 $17,662 $16, N-- CBT L " 0.45 $20,891 $19, N-- CBT L " Wide $14,342 $11, N-- CBT L " Wide $17,046 $14, N-- CBT L " Wide $29,876 $28, N-- CBT L " Wide $37,344 $36, N-- CBT L " Wide N/A $34,469 Snyder recommends cone bottom tank applications DO NOT EXCEED 100º F. Note: Cone Bottom tanks are not ASTM D1998 design. 30 Issued

31 CONE BOTTOM TANK STANDS Small Cone Bottom Stands Snyder Part # Tank Capacity List Price $ $ , 65 & 110 $ Cone Stands Standard Seismic Snyder Part # Snyder Part # Tank Stand No. of Recommended Stand Stand Std. Stand Seismic Stand Diameter Capacity Legs Tank Capacity List Price List Price " 14 Tons 4 CBT 500, 1000 $1,822 $1, " 14 Tons 4 CBT 1400, 1650 $1,822 $2, " 65 Tons 12 CBT 2000, 2500, 3000 $2,921 $2, " 65 Tons 12 CBT $2,921 $3, N/A 90" 65 Tons 12 CBT 5500,6500* $2,921 N/A N/A 95" 50 Tons 8 CBT 1250, 1600, 2500, 3000 $2,921 N/A " 100 Tons 12 CBT 6000, 7400 $6,048 $6, " 100 Tons 12 CBT 11,500, 13,000 $6,047 **Call *Seismic stand not available on 90" CBT over 4400 Gallons. Note: See page 35 for CBT Seismic Restraint System information. **Call for Price. 45 Degree Cone Stands Standard Seismic Snyder Part# Snyder Part # Tank Stand No. of Recommended Tank Stand Stand Std. Stand Seismic Stand Diameter Capacity Legs Capacity List Price List Price " 12 Tons 4 CBT 500, 1000, 1500 (1.6) $1,783 $1, " 12 Tons 4 CBT 1500 (1.9) $1,784 $2, " 60 Tons 12 CBT 2600 $3,147 $3, " 60 Tons 12 CBT 4100 $3,148 $7,400 Note: See page 35 for CBT Seismic Restraint System information. 31

32 INTERMEDIATE BULK CONTAINERS-IBCs Distributors Note: Your discount on IBC s may differ from your standard discount for the Industrial product line. IBCs are not available for sale in all states due to distribution agreements in place. Contact Snyder if located in these states: AK, AL, AR,CO, FL, GA, LA, MS, NM, SC, TX WY, and in these Candian Provinces: AB, BC, MB, SK. Standard Square Stackable - F.O.B. Lincoln, NE 4 way heavy duty black, 2 2 Bung, 2 ball valve, 6 cap & vacuum vent. Snyder Lid List* Part No. Gallon Weight Length Width Height Opening Price ½ 6 $1, ½ 6 $1, ½ 6 $1, ½ 6 $1,434 Premium Square Stackable - F.O.B. Lincoln, NE 4 way premium red base, 2-2" bungs, 2" ball valve, 6" cap, vacuum vent ½" 6 $1, ½" 6 $1, " 6 $1, ½" 6 $1,572 Standard Ultratainer - F.O.B. Lincoln, NE Blue base, 2-2" bungs, 2" ball valve, 6" cap, vacuum vent " 6 $2, " 6 $2, " 6 $2,296 32

33 Wide Mouth Ultratainer - F.O.B. Lincoln, NE Blue base, 2-2" bungs, 2" ball valve, 20" lid, vacuum vent " 22 /6 $2, " 22 /6 $2, " 22 /6 $2,609 Megatainer** - F.O.B. Mancelona, MI Red base, 1-2" bung, 6" cap, vacuum vent. LX version not top lift capable " 6 $4, LX " 48" 60" 6" $3,121 Excalibur - F.O.B. Lincoln, NE S.G $ S.G $1, S.G $1,324 Saf-Tainer* - F.O.B. Lincoln, NE ½" Basin $ Stand " Stand $1,506 *Grating for Saf-Tainer required for steel or steel-caged IBC s. Add $ List Price **Grating for Megatainer Add $ List Price Viton Gasket Package (Lid & Top Bung Locations) Add $78.00 List Price / Stacked Discharge Vent & Hose Assembly Set $560 Spil-Tainer Drum Containment Units - F.O.B. Bensenville, IL Part # Product Description Weight Length Width Height List Price T88701 Spil-Tainer - One Drum Unit 23 lbs. 30" 30" 26" Basin $ T88701 Optional One Drum Cover 22 lbs. Cover $ T88701 Spil-Tainer - Two Drum Unit 44 lbs. 50" 40" 24" Basin $ T88701 Optional Two Drum Cover 33 lbs. Cover $ T88701 Spil-Tainer - Four Drum Unit 53 lbs. 50" 50" 17" Basin $ T88701 Optional Four Drum Cover 50 lbs. Cover $350 33

34 Tank Accessories Flexmaster* Recommended to extend tank life Snyder Part No. Product Description List Price Gaskets for Flexmaster's are not N Flange Connector Assembly HDLPE $531 included in price. See page N Flange Connector Assembly XLPE $693 for gasket pricing N Flange Connector Assembly HDLPE $ N Flange Connector Assembly XLPE $882 *For Sulfuric applications specify resin # , and add 15% to list price. *For Opaque White Flexmasters for use with Sodium Hypochlorite (outdoors) specify Opaque resin # , and add 35% to list price. Insulation* - (VST, CCS, DCT) (Grey) Price/Gal. List Price/Gal. Snyder Part No. Available: Lincoln, NE. Only VSTs DCT & Captor and below Gallon capacity (Vertical Storage Tanks only - Lincoln, NE only) $3.11 $ Gallon capacity (Vertical Storage Tanks only - Lincoln, NE only) $2.03 $ Gallon capacity (Vertical Storage Tanks only Lincoln, NE only) $1.37 $ ,500 Gallon capacity (Vertical Storage Tanks only - Lincoln, NE only) $0.87 $ ,800 Gallon tank insulation (transfers from Ohio to Lincoln and then ships from Lincoln) $22, Insulation Repair Kit $74 Factory installed nominal 2" thick polyurethane foam insulation with two coats of grey latex mastic coating. Consult Factory for Heat System Pricing- Be able to provide tank size, temperature to be maintained & minimum ambient temperature. For 1" insulation - use 0.71 multiplier. (2" List x.71 = 1" List) *Minimum charge $ List Ladders/Safety Cage All Captor Containment Systems (CCS) and Vertical Storage Tank 2000 gallons & above. Contact factory for special applications To price ladders, take the overall height of the tank and round up to the nearest foot, and take that number x the per foot pricing. Then add the appropriate ladder attachment price. Ladder Part Number List Price/foot List Price/foot Gav. Steel FRP Ladders Galv. Steel Ladder FRP Ladder 339--GS 339-FRP Ladder for Vertical Storage Tanks (2,000-20,000 gallons)* $173 (min. $900) $292 (min.$1500) Ladder Attachment Kit (must add one per ladder) $562 $ Laddder Attachment Kit (13,800 & 18, " diameter tanks). $562 $ STLCAGE 347-FRPCAGE Cage** (Vertical Storage Tank only) - starts 7' up from ground $188 (min. $752) $328 (min. $1312) FRP ladders are supplied in safety yellow. *Ladders are available for tanks with molded-in lifting lugs only. **Cage not required on tanks less than 20' high. *Insulated tanks must be wrapped for shipment. (See page 2 for wrap pricing). *Insulated tanks shipping LTL should be crated for shipment. 34

35 Tank Accessories Seismic Restraint Systems & 316 Stainless Steel - call factory for pricing. Snyder Part No. Vertical Single Wall Tanks (see page 8-9 for double wall tanks) System Add'l Anchors ,35,55,60,120,150,275,360,500 VFT, VOT Tanks $1,025 N/A gallon capacity Vertical StorageTank $1,024 $159 ea gallon capacity Vertical Storage Tank $1,473 $235 ea ,800 gallon capacity Vertical Storage Tank $2,183 $293 ea ,000-20,000 gallon capacity Vertical Storage Tank $3,598 $293 ea. System includes: Galvanized steel anchors, cable, U-bolt clips, thimbles and sheathing. ANCHOR BOLTS ARE NOT INCLUDED AND MUST BE PURCHASED SEPARATELY. Seismic Tie-down System is also available in stainless steel; contact Sii for pricing. For 5500x90" VST out of Lincoln and all 86" & 102" diameter VSTs out of Marked Tree - NO SEISMIC RESTRAINT SYSTEMS AVAILABLE. For Seismic Systems on tanks without any molded in tie-down lugs and for 165" diameter tanks - Contact Sii for system pricing. System meets IBC 2015 / CBC 2016 code with seismic loads.445g (Seismic Design Category "D" - Fa=1.0, Fv=1.5, Ss=1.4, S1=0.5) Snyder Part No. Cone Bottom Tanks - (not available on Marked Tree or Chowchilla tanks) List Price gallon capacity Cone Bottom Storage Tank $ ,000 gallon capacity Cone Bottom Storage Tank (not available for 5500 & 6500)* $1,971 System includes: Coated carbon steel anchors, cable, sheathing, U-bolt clips, thimble, eye bolt, complete instructions. Seismic Tie-down System is also available in stainless steel; contact Sii for pricing. SYSTEMS DO NOT INCLUDE ANCHOR BOLTS. System meets IBC 2006 / CBC 2007 code with seismic loads.33g (Seismic Design Category "D"- Fa=1.0, Fv=1.5, SDS=1.105, SD1=0.597). *Seismic System not available on 90" CBT over 4400 gallons. Snyder Part No. Original Wet Stamp Original Wet Stamp Calculations VST/CCS/DCT/CBT - Standard Calculation $1, Original Wet Stamp Calculations VST/CCS/DCT-Site specific - Standard Format $3, Original Wet Stamp Calculations CBT-Site specific - Standard Format $5,028 Wet stamps available for CA, AZ, OR, WA, and NV on VST & CCS only. DCT & CBT stamps available for CA, WA, NV only. Other states can be stamped but additional fees may apply. Contact factory for wet stamp prices in other states. Call for pricing on all non-molded in lug tank seismic calculations. Some applications may require the use of additional anchors due to fitting, sumo, or ladder location. 35

36 TANK ACCESSORIES Lateral Restraints - vertical tanks only Snyder Part # Product Description List Price Assembly tie down 48" & 64" Lateral, Black $ Assembly tie down 86", 90" & 102" Lateral, Black $ Assembly tie down 120" & 142" Lateral, Black $405 Gallonage Indicators Adhesive Decals- Vertical Storage Tanks Only Snyder Part # Note: Indicates capacity in 100 gallon increments, identifies gallons in 500 gallon increments. List Price " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks Gallon Maximum $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $ " Diameter Vertical Storage Tanks $68 Snyder Part # NAME PLATES - F.O.B. Lincoln, NE List Price Nameplate, 304SS, 8"x5" (5 lines) Add $44.00 list per additional line (if space available) $ Nameplate, 304SS, 12"x8" (8 lines) Add $44.00 list per additional line (if space available) $ Welded-on mounting block for name plate $391 Snyder Part # Ultrasonic Level Indicator List Price Ultrasonic Level Indicator includes fitting. For tanks 79" or taller only. $3, Ultrasonic Level Indicator includes fitting. For tanks 78" or shorter only. $3,215 Snyder Part # Sight Gauge Assembly (PVC) See page 9 on sightglass assembly for double wall tanks. List Price Sight Gauge Assembly Bulkhead Threaded Fittings w/epdm gaskets w/o valves $ Sight Gauge Assembly Bulkhead Threaded Fittings w/viton gaskets w/o valves $ Sight Gauge Assembly Bolted Fittings w/epdm gaskets w/o valves (SS bolts Encap.) $ Sight Gauge Assembly Bolted Fittings w/viton gaskets w/o valves (SS bolts Encap.) $1,103 Note: Above assembly includes (2) ¾ fittings (PVC); (2) ¾ Nipples (PVC); (2) Hose barbs & clamps; flex tube; gaskets. 36

37 TANK ACCESSORIES Snyder Part # Sight Gauge Assembly (CPVC) EPDM VITON EPDM VITON Sight Gauge Assembly Bulkhead Threaded Fittings w/o valves $338 $445 Note: Above assembly includes (2) ¾ fittings (CPVC); (2) ¾ Nipples (CPVC); (2) Hose barbs & clamps; flex tube; gaskets. List Price List Price PVC CPVC Valves for Sight Gauge Assembly PVC CPVC (1) ¾ Valve (includes valve, nipple and sealant) VITON O Rings $122 $ (1) ¾ Drain Valve w/tee (includes valve w/ VITON gasket, tee, nipple and sealant) $153 $ (1) ¾ Valve (includes valve, nipple and sealant) EPDM O Rings $106 $ (1) ¾ Drain Valve w/tee (includes valve w/ EPDM gasket, tee, nipple & sealant) $136 $163 Snyder Part # Reverse Float Indicators Vertical Storage Tanks Only List Price List Price EPDM Viton for Captors (CCS) see Page 9. EPDM Viton Reverse Action Float Level Gallonage Indicator - PVC/PP $1,594 $1, Reverse Action Float Level Gallonage Indicator-CPVC/PVC/PP - for sulfuric acid tanks Reverse Stenciled Calibration Board (Optional) $488 Snyder Part # PVC/CPVC External Downpipe Assembly Tank Supported List Price List Price PVC/epdm PVC/viton CPVC/viton Schedule 80 PVC/CPVC w/viton Gaskets PVC(epdm or viton) CPVC Downpipe Assembly 2" (Fitting not included) $338 $ Downpipe Assembly 3" (Fitting not included) $601 $ Downpipe Assembly 4" (Fitting not included) $695 $1, NA Downpipe Assembly 6" (Fitting not included) $1,072 N/A Note: Includes PVC/CPVC male adapter, (2) 90 PVC/CPVC elbows, 10' PVC/CPVC pipe, 1 saddle clamp support assembly - saddle clamp (PVC). PVC/CPVC: External Fill Pipe Assemblies Ground Supported List Price List Price Snyder Part # FOR CAPTOR CONTAINMENT SYSTEMS but can be used on VST s (Does Not Include Fitting.) PVC CPVC " External Fill Pipe Assembly - with FRP strut $654 $ " External Fill Pipe Assembly - with FRP strut $1,205 $1, " External Fill Pipe Assembly - with FRP strut $1,375 $2, / " Valve/Elbow Assembly for External Fill Assembly - PVC, PP $214 $ / " Valve/Elbow Assembly for External Fill Assembly - PVC, PP $514 $696 Note: Includes 1 PVC/CPVC Male Adapter, (10 ft. Schedule 80 PVC/CPVC Pipe), 2 90 Elbows, 1 FRP Strut Assembly. $3,408 37

38 TANK ACCESSORIES Downpipe Support Saddle Clamp Assembly (Schedule 80 PVC) Does not include top fitting Snyder Part # Product Description List Price Downpipe Saddle Clamp Assembly 2" (PVC) w/epdm (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 3" (PVC) w/epdm (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 4" (PVC) w/epdm (Includes 2" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 6" (PVC) w/epdm (Includes 2" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 2" (PVC) w/viton (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 3" (PVC) w/viton (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 4" (PVC) w/viton (Includes 2" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 6" (PVC) w/viton (Includes 2" Bulkhead threaded fitting for sidewall support) $139 $153 $245 $384 $169 $184 $277 $428 Includes: Bulkhead threaded fitting, male adaptor, 4' of PVC support pipe, PVC slip plug, & PVC saddle clamp. Downpipe Support Saddle Clamp Assembly(Schedule 80 CPVC) Does not include top fitting Snyder Part # Product Description List Price Downpipe Saddle Clamp Assembly 2" (CPVC) w/viton (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 3" (CPVC) w/viton (Includes 1" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 4" (CPVC) w/viton (Includes 2" Bulkhead threaded fitting for sidewall support) Downpipe Saddle Clamp Assembly 6" (CPVC) w/viton (Includes 2" Bulkhead threaded fitting for sidewall support) $206 $230 $351 $414 Includes: Bulkhead threaded fitting, male adaptor, 4' of CPVC support pipe, CPVC slip plug, & PVC saddle clamp. 38

39 TANK ACCESSORIES Welded Internal Support Saddle Clamp Assembly (PE/PVC) on HDLPE tanks only Snyder Part # Product Description Note: Internal Use Only List Price Welded support saddle clamp assembly (PE/PVC) $ Welded support saddle clamp assembly (PE/PVC) $ Welded support saddle clamp assembly (PE/PVC) $ " Welded support saddle clamp assembly (PE/PVC) $ ", 2, 3" or 4 Welded support assembly (PE/PE)* $246 * Pipe installed during shipment PVC PIPE - Schedule 80 CPVC PIPE - Schedule 80 List Price PVC CPVC Product Description PVC CPVC Pipe 1" (PVC) Schedule 80 Pipe 1" (CPVC) Schedule 80 $2 $ Pipe 2" (PVC) Schedule 80 Pipe 2" (CPVC) Schedule 80 $6 $ Pipe 3" (PVC) Schedule 80 Pipe 3" (CPVC) Schedule 80 $12 $ Pipe 4" (PVC) Schedule 80 Pipe 4" (CPVC) Schedule 80 $17 $ Pipe 6" (PVC) Schedule 80 $53 $136 Note: Per foot pricing. Factory Testing Snyder Part # VST's, VOT's, CCS's, & DCT's only List Price Hydrotest - Below 2000 Gallon capacity - 4 hour $ Hydrotest ,500 Gallon capacity - 4 hour $ Gel Test (XLPE tanks only) - all sizes (allow 2-4 weeks) $ ASTM Documentation (VST, VOT, CCS & DCT 500 Gal. and above) $54 Must be ordered to comply with testing requirements for ASTM D1998 certification. *Hydrotest not available for tanks out of Washington Court House, Ohio Hole Cut Charges Snyder Part # (For customer supplied fittings) List Price Threaded Fitting - hole cut only $ Bolted Fitting - hole cut only $ Custom hole cuts or cutting top off tank $310 39

40 TANK ACCESSORIES Siphon Tube - Schedule 40 PVC Slip Fit (Does not include fitting) Snyder Part # Product Description List Price Siphon Tube 1" - (PVC) Slip Fit $ Siphon Tube 1 1/2" - (PVC) Slip Fit $ Siphon Tube 2" - (PVC) Slip Fit $ Siphon Tube 3" - (PVC) Slip Fit $ Siphon Tube 4" - (PVC) Slip Fit $ Siphon Tube 6" - (PVC) Slip Fit $ Siphon Tube 8" - (PVC) Slip Fit $509 Siphon Tube Poly Pro Threaded (Does not include fitting) Snyder Part # Product Description List Price Siphon Tube 2 Poly Pro Threaded $ Siphon Tube 3 Poly Pro Threaded $157 NOTE: Can be utilized on thread by thread fittings. Siphon Tube - Schedule 80 CPVC Slip Fit (Does not include fitting) List Price Siphon Tube 1" - (CPVC) Slip Fit $ Siphon Tube 1 1/2" - (CPVC) Slip Fit $ Siphon Tube 2" - (CPVC) Slip Fit $ Siphon Tube 3" - (CPVC) Slip Fit $ Siphon Tube 4" - (CPVC) Slip Fit $ Siphon Tube 6" - (CPVC) Slip Fit $313 Mushroom Vents - PP and HDPE List Price " Threaded Vent w/mesh Screen - does not include fitting $ " Threaded Vent w/mesh Screen - does not include fitting $ N " Mushroom Vent Assy w/mesh screen - no fitting required. $373 U-Vent Schedule 40 PVC (Does not include fitting) List Price U Vent 1" (PVC) $ U Vent 1-1/2" (PVC) $ U Vent 2" (PVC) $ U Vent 3" (PVC) $ U Vent 4" (PVC) $ U Vent 6" (PVC) $365 * Manways listed as fitting most tanks will fit tanks if enough flat space permits - check tank drawings 40 Note: Optional 17x17 Mesh Bug Screen (Part # $25.00 list.)

41 TANK ACCESSORIES Siphon U-Vent Tube - Schedule - 80 CPVC 40 PVC (Does Slip not Fit include (Does fitting) not include fitting) List Price U Vent 1" (CPVC) $ U Vent 1-1/2" (CPVC) $ U Vent 2" (CPVC) $ U Vent 3" (CPVC) $ U Vent 4" (CPVC) $ U Vent 6" (CPVC) $771 Access Manway and Fill Caps Style Opening October 1, 2017 Fits all Captors & VSTs Listed " Removeable Vent (replacement for ) $ " Cap (PE) - Vented Threaded Cap 4-1/2" molded fill neck $ " Manway (PE) - Vented Threaded 8" most tanks* $ " Cap (PE) - Vented Threaded Cap 7" molded fill neck $ " Manway (PE) - Vented Threaded 11-1/4" most tanks* $ " Manway (PE) - No Vent Threaded 11-1/4" most tanks* $ " Manway (PP) - Vented Hinged - no lock 11" most tanks* $ " Manway (PP) - Vented Hinged - with lock 11" most tanks* $ " Manway (PP) - "Air Surge" Hinged - Air Surge 11" most tanks* $ " Manway (PP) - "Air Surge" w/insect screen Hinged - Air Surge 11" most tanks* $ " Manway (PE) - Fume Tight Bolted Sealed 10" most tanks* $ " Manway (PE) - Vented Threaded 15" 48" - 143" dia. $ " Manway (PE) - No Vent Threaded 15" 48" - 143" dia. $ " Manway (PP) - Vented Hinged - with lock 15" 48" - 143" dia. $ " Manway (PP) - "Air Surge" Hinged - Air Surge 15" 48" - 143" dia. $ " Manway (PE) - Fume Tight Bolted Sealed 13 1/2" 48" - 143" dia. $ " Manway (PE) - Fume Tight Bolted Sealed 17" 90" - 143" dia. $ " Manway (PE) - Vented Threaded 22" 90" - 143" dia. $ " Manway (PE) - No Vent Threaded 22" 90" - 143" dia. $ " Manway (PP) - Vented** Hinged - with lock 22" 90" - 143" dia. $ " Manway (PE) - Fume Tight Bolted Sealed 20" 90" - 143" dia. $602 * Manways listed as fitting most tanks will fit tanks if enough flat space permits - check tank drawings ** 24" hinged manway will not work on 90" diameter tanks if there is a ladder assembly installed. Note: Optional 17x17 Mesh Bug Screen (Part # $25.00 list.) Note: If 6" CPVC male adapter is needed for 6" CPVC U-vent, add # ($487 list) List Price 41

42 TANK ACCESSORIES Flange Adaptor (Schedule 80 PVC) (Does Not Include Fitting) Bolted Fitting Flange Adaptor Bulkhead Threaded Fitting Flange Adaptor (Includes Flange, 12 Pipe for Bolted Fittings) List Price (Includes Flange, 12" Pipe & Male Adaptor) List Price Flange Adaptor 1" - PVC Slip Fit $ Flange Adaptor 1/2" (PVC) $ Flange Adaptor 1 1/2" - PVC Slip Fit $ Flange Adaptor 3/4" (PVC) $ Flange Adaptor 2" - PVC Slip Fit $ Flange Adaptor 1" (PVC) $ Flange Adaptor 3" - PVC Slip Fit $ Flange Adaptor 1-1/2" (PVC) $ Flange Adaptor 4" - PVC Slip Fit $ Flange Adaptor 2" (PVC) $ Flange Adaptor 6" - PVC Slip Fit $ Flange Adaptor 3" (PVC) $ Flange Adaptor 8" - PVC Slip Fit $ Flange Adaptor 4" (PVC) $ Flange Adaptor 6" (PVC) $346 Flange Adaptor (Schedule 80 CPVC) Does not include Fitting Bolted Fitting Flange Adaptor Bulkhead Threaded Fitting Flange Adaptor (Includes Flange, 12 Pipe for Bolted Fittings) List Price (Includes Flange, 12 Pipe & Male Adaptor) List Price Flange Adaptor 1" - CPVC Slip Fit $ Flange Adaptor 3/4" (CPVC) $ Flange Adaptor 1 1/2" - CPVC Slip Fit $ Flange Adaptor 1" (CPVC) $ Flange Adaptor 2" - CPVC Slip Fit $ Flange Adaptor 1-1/2" (CPVC) $ Flange Adaptor 3" - CPVC Slip Fit $ Flange Adaptor 2" (CPVC) $ Flange Adaptor 4" - CPVC Slip Fit $ Flange Adaptor 3" (CPVC) $ Flange Adaptor 6" - CPVC Slip Fit $ Flange Adaptor 4" (CPVC) $ Flange Adaptor 8" - CPVC Slip Fit $ Flange Adapter 6" (CPVC) $876 8" Flange Adapter in CPVC is not available 42

43 TANK ACCESSORIES GASKETS Threaded - (For use with PVC, CPVC or PP Bulkhead Fittings) Snyder Part No. Size Material List Price Snyder Part No. Size Material List Price /2" Threaded EPDM $ /2" VITON $ /4" Threaded EPDM $ /4" VITON $ " Threaded EPDM $ " VITON $ /2" Threaded EPDM $ /2" VITON $ " Threaded EPDM $ " VITON $ " Threaded EPDM $ " VITON $ " Threaded EPDM $ " VITON $ " Threaded EPDM $ " VITON $400 Bolted - (For use with PVC or CPVC Bolted Fittings & Flexmasters) Snyder Part No. Size Material List Price Snyder Part No. Size Material List Price " Bolted EPDM $ " VITON $ /2" Bolted EPDM $ /2" VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $919 Bolted - (For use with 316 S.S. Fittings) Snyder Part No. Size Material List Price Snyder Part No. Size Material List Price /2" Bolted EPDM $ /2" VITON $ /4" Bolted EPDM $ /4" VITON $ " Bolted EPDM $ " VITON $ /2" Bolted EPDM $ /2" VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $ " Bolted EPDM $ " VITON $147 43

44 FITTINGS U-Vent Assembly (Schedule 40 PVC) w/bulkhead Fitting (Threaded) U-Vent w/bulkhead Fitting U-Vent w/bulkhead Fitting Threaded w/epdm Threaded w/viton Gasket List Gasket List Size Part No. Material Price Size Part No. Material Price 1" EPDM $95 1" VITON $111 2" EPDM $137 2" VITON $161 3" EPDM $204 3" VITON $302 4" EPDM $450 4" VITON $675 6" EPDM $955 6" VITON $1,153 Note: Above prices include U-vent, bulkhead fitting (threaded), gasket material, hole cut. Note: Optional 17X17 Mesh Bug Screen (Part # $25.00 List). Mushroom Vent (HDPE) - Ideal for pneumatic fill applications. Snyder Part No. Product Description List Price N " Mushroom Vent Assembly, HDPE $373 Note: minimum 19" diameter of flat area on top of tank required for installation. Note: comes standard with 1/8" Mesh Bug Screen. 44

45 Siphon Tube Assembly (Schedule 40 PVC) w/bulkhead Fitting Siphon Tube w/bulkhead Fitting Threaded w/epdm Siphon Tube w/bulkhead Fitting Threaded w/viton Size Part No. Gasket List Price Part Gasket List Material Size No. Material Price 2" EPDM $167 2" VITON $196 3" EPDM $299 3" VITON $390 Note: Above items include siphon tube, bulkhead fitting (threaded), gasket material, hole cut. Note: Siphon tube 9" long. Note: 3" siphon tube to be installed on flat spot. Threaded Fittings (CORZAN CPVC) Socket by Thread Bulkhead Fitting (CPVC) Threaded w/epdm Bulkhead Fitting (CPVC) Threaded w/viton Part Gasket List Part Gasket List Size No. Material Price Size No. Material Price 1/2"` EPDM $100 1/2" VITON $113 3/4" EPDM $100 3/4" VITON $115 1" EPDM $106 1" VITON $ /2" EPDM $ /2" VITON $171 2" EPDM $156 2" VITON $181 3" EPDM $220 3" VITON $291 4" EPDM $399 4" VITON $587 6" EPDM $1,319 6" VITON $1,558 Note: Above prices include fitting, gasket material and hole cut. Note: Designated units should not be installed on vertical tank wall outside of flat locations. Note: Add 10% for thread by thread or socket by socket. 45

46 FITTINGS Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with additional questions. BULKHEAD THREADED FITTINGS Threaded Fitting (PVC) - NSF Socket by Thread Bulkhead Fitting Bulkhead Fitting (PVC) Threaded w/epdm (PVC) Threaded w/viton Part Gasket List Part Gasket List Size No. Material Price Size No. Material Price 1/2" EPDM $71 1/2" VITON $92 3/4" EPDM $79 3/4" VITON $93 1" EPDM $82 1" VITON $94 1-1/2" EPDM $94 1-1/2" VITON $108 2" EPDM $113 2" VITON $152 3" EPDM $170 3" VITON $237 4" EPDM $317 4" VITON $535 6" EPDM $820 6" VITON $1,072 Note: Above prices include fitting, gasket material, hole cut. Units should not be installed on vertical tank wall outside of flat locations. Note: Add 10% for thread by thread or socket by socket. Note: Threaded Bulkhead Fittings 46 Tank Dia. Max. Sidewall Fitting Size Allowed 18" 1" 22", 30" 1.5" 36", 45" 2" 48"- 165" 2"

47 Threaded Fitting (Natural PP) - Thread x Thread Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. Bulkhead Fitting Bulkhead Fitting (PP) Threaded w/epdm (PP) Threaded w/viton Part Gasket List Part Gasket List Size No. Material Price Size No. Material Price 1/2" EPDM $70 1/2" VITON $100 3/4" EPDM $82 3/4" VITON $106 1" EPDM $98 1" VITON $ /2" EPDM $ /2" VITON $142 2" EPDM $166 2" VITON $195 3" EPDM $327 3" VITON $391 4" EPDM $530 4" VITON $704 Note: Above prices include fitting, gasket material, hole cut. Units should not be installed on vertical tank wall outside of flat locations. Threaded Fitting (PE) - Thread by Thread Bulkhead Fitting (P.E.) Threaded w/epdm (P.E.) Threaded w/viton Part Gasket List Part Gasket List Size No. Material Price Size No. Material Price 1" EPDM $66 1" VITON $ /2" EPDM $86 1 1/2" VITON $120 2" EPDM $111 2" VITON $164 3" EPDM $129 3" VITON $240 Note: Above prices include fitting, gasket & hole cut. Note: Threaded Bulkhead Fittings 3" size is glass filled polypropylene. Max. Sidewall Fitting Units should not be installed on vertical Tank Dia. Size Allowed tank wall outside of flat locations. 18" 1" Tank wall thickness may not allow some sizes on sidewall 22", 30" 1.5" 47 36"- 45" 2" 48"- 165" 2" Bulkhead Fitting

48 Snyder Unitized Molded Outlet - SUMO Fitting ( ,500 Gallons) Stainless SUMO Product Description List Price Steel (includes PVC adapter & Viton O-rings as standard) Stainless List Price List Price EPDM VITON Titanium Hastelloy Applies to Vertical Storage Tanks Only Steel Titanium Hastelloy " Encapsulated Bottom Drain Outlet $354 $1,017 $ " Encapsulated Bottom Drain Outlet $512 $1,239 $ * 4" Encapsulated Bottom Drain Outlet $1,530 $1,933 $3, * 6" Encapsulated Bottom Drain Outlet $2,164 $3,685 $3,826 NOTE: Available in 4 (90 ) locations on ,500 Vertical Storage Tanks. Not available on 1.35 and 1.5 Specific Gravity VSTs. Not available on 4500x142 or 5600x142. For Marked Tree tanks, SUMOs are available on 90" and 102" diameter VSTs only. For California tanks, SUMOs are available on 2000 VST 10,500 VST. NOTE: (2) SUMO Maximum per tank within 90 of each other on 90 diameter and above. * Available on ,500, 120" and 142" diameter tanks. Only (1) 4" or 6" per tank. 48

49 Snyder Unitized Molded Outlet Sumo Adapters SUMO ADAPTERS MPT x SOC PVC SUMO ADAPTERS MPT x MPT Part List 316 Stainless Steel Size No. Price Part List 2" $79 Size No. Price 3" $108 2" $580 4" $270 3" $720 6" $532 SUMO ADAPTERS MPT x SOC SUMO O-RINGS(replacement) List CPVC Part No. Size Gasket Price Part List / " EPDM $29 Size No. Price / " Viton $31 2" $ / " EPDM $34 3" $ / " Viton $36 4" $ / " EPDM $43 6" $ / " Viton $ / " EPDM $54 Replacement SUMO adapters / " Viton $109 Note: O-rings not included. 2 required per SUMO. Includes both O-rings Bulkhead Self-Aligning Fittings - (PVC) Threaded Thread by Thread Bulkhead Self-Aligning Fitting (PVC) Threaded w/ VITON Bulkhead Self-Aligning Fitting Note: Install on Part Gasket List (PVC) Threaded w/ EPDM top of tank Size No. Material Price Part Gasket List 1" VITON $309 Size No. Material Price 2" VITON $471 1" EPDM $285 3" VITON $797 2" EPDM $420 CPVC 3" EPDM $631 1" VITON $486 Note: Above prices include fitting, gasket material, hole cut. Note: Indicated gasket material standard is one (1) size larger than requested fitting. 2" VITON $748 3" VITON $1,143 49

50 FITTINGS BOLTED DOUBLE FLANGED FITTINGS (PP) Bolted SS Bolts October 1, 2017 Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. Double Flanged Fitting-(PP) Bolted Thread by Thread Double Flanged Fitting-(PP) Bolted w/epdm Stainless Steel Bolts w/viton Stainless Steel Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 3/4" EPDM 4 3/8" $98 3/4" VITON 4 3/8" $183 1" EPDM 4 3/8" $136 1" VITON 4 3/8" $ /2" EPDM 4 3/8" $ /2" VITON 4 3/8" $256 2" EPDM 4 3/8" $148 2" VITON 4 3/8" $266 3" EPDM 6 3/8" $220 3" VITON 6 3/8" $459 4" EPDM 8 5/8" $869 4" VITON 8 5/8" $1,285 Note: All fittings consist of (2) PP flanges, (2) gaskets, designated number of SS bolts, gaskets, hole cut. Note: Outside/Inside ID: 3/4"x 1"; 1 1/2" x 2" PP BOLTED TOTAL DRAIN FITTINGS-SS BOLTS Double Flanged Total Drain Fitting-(PP) FOR CBT & TOTAL DRAIN TANKS Double Flanged Total Drain Fitting-(PP) Bolted w/epdm Stainless Steel Bolts Bolted w/viton Stainless Steel Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 2" EPDM 4 3/8" $155 2" VITON 4 3/8" $279 3" EPDM 6 3/8" $235 3" VITON 6 3/8" $482 Thread x Thread 50 Max. size sidewall bolted fitting allowed. Tank PVC Diameter CPVC PP SS 18" 1" 2" 1 1/2" 22"-29" 1 1/2" 2" 2" 30" 2" 2" 2" 36"-45" 2" 2" 2" 48"-86" 3" 3" 4" 90"-102" 6" 3" 4" 120"-165" 8" 3" 4"

51 FITTINGS Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. Double Flanged Fitting-(SS) Bolted w/epdm Stainless Steel Bolts w/viton Stainless Steel Bolts Part Gasket No. of Dia. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1/2" EPDM 4 3/8" $134 1/2" VITON 4 3/8" $179 3/4" EPDM 4 3/8" $139 3/4" VITON 4 3/8" $182 1" EPDM 4 3/8" $142 1" VITON 4 3/8" $ /2" EPDM 4 3/8" $ /2" VITON 4 3/8" $255 2" EPDM 4 3/8" $203 2" VITON 4 3/8" $261 3" EPDM 6 3/8" $339 3" VITON 6 3/8" $378 4" EPDM 8 3/8" $496 4" VITON 8 3/8" $676 Note: All fittings consist of (2) SS flanges, (1) gasket, designated number of SS bolts, hole cut. Double Flanged Fitting-(PVC) Bolted w/epdm Stainless Steel Bolts Socket by Socket w/viton Stainless Steel Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" EPDM 4 1/2" $223 1" VITON 4 1/2" $ /2" EPDM 4 1/2" $ /2" VITON 4 1/2" $450 2" EPDM 4 5/8" $264 2" VITON 4 5/8" $445 3" EPDM 4 5/8" $309 3" VITON 4 5/8" $577 4" EPDM 8 5/8" $503 4" VITON 8 5/8" $836 *6" EPDM 8 3/4" $641 *6" VITON 8 3/4" $1,351 *8" EPDM 8 3/4" $1,040 *8" VITON 8 3/4" $2,190 Cannot be used on tanks with a 14" or smaller manway or 18" bolted manway. Note: All fittings consist of (2) PVC flanges, (2) gaskets, STAINLESS STEEL Thread by Thread Double Flanged Fitting-(SS) Bolted PVC-SS Bolts Double Flanged Fitting-(PVC) Bolted Max. size sidewall bolted fitting allowed. designated number of SS bolts with gaskets, hole cut. Tank PVC Add 10% for thread by thread. Diameter CPVC PP SS *Thread by thread not available. 18" 1" 2" 1 1/2" 22"-29" 1 1/2" 2" 2" 30" 2" 2" 2" 36"-45" 2" 2" 2" 48"-86" 3" 3" 4" Note: If ordering loose uninstalled fittings, specify tank size and S.G. to ensure bolt length provided 90"-102" 6" 3" 4" is adequate. 120"-165" 8" 3" 4" 51

52 FITTINGS DOUBLE FLANGED FITTINGS - PVC Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. (PVC) Bolted Encapsulated SS Bolts Socket by Socket DBL Flanged Fitting-(PVC) Bolted DBL Flanged Fitting-(PVC) Bolted w/epdm Stainless Steel Encapsulated Bolts w/viton Stainless Steel Encapsulated Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" EPDM 4 1/2" $278 1" VITON 4 1/2" $ /2" EPDM 4 1/2" $ /2" VITON 4 1/2" $501 2" EPDM 4 5/8" $305 2" VITON 4 5/8" $479 3" EPDM 4 5/8" $358 3" VITON 4 5/8" $616 4" EPDM 8 5/8" $592 4" VITON 8 5/8" $962 *6" EPDM 8 3/4" $723 *6" VITON 8 3/4" $1,487 *8" EPDM 8 3/4" $1,137 *8" VITON 8 3/4" $2,205 Note: All fittings consist of (2) PVC flanges, (2) gaskets, designated number of polyethylene encapsulated stainless bolts with gaskets, hole cut. Add 10% for thread by thread. Max. size sidewall bolted fitting allowed. *Thread by thread not available. Tank PVC Diameter CPVC PP SS 18" 1" 2" 1 1/2" 22"-29" 1 1/2" 2" 2" 30" 2" 2" 2" 36"-45" 2" 2" 2" 48"-86" 3" 3" 4" 90"-102" 6" 3" 4" 120"-165" 8" 3" 4" 52

53 FITTINGS DOUBLE FLANGED FITTINGS - PVC Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. (PVC) Encapsulated Titanium Bolts Socket by Socket October 1, 2017 DBL Flanged Fitting-(PVC) Bolted DBL Flanged Fitting-(PVC) Bolted w/epdm - Encapsulated Titanium Bolts w/viton - Encapsulated Titanium Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" EPDM 4 1/2" $618 1" VITON 4 1/2" $ /2" EPDM 4 1/2" $ /2" VITON 4 1/2" $877 2" EPDM 4 5/8" $799 2" VITON 4 5/8" $1,019 3" EPDM 4 5/8" $865 3" VITON 4 5/8" $1,171 4" EPDM 8 5/8" $1,583 4" VITON 8 5/8" $1,972 *6" EPDM 8 3/4" $2,062 *6" VITON 8 3/4" $2,901 *8" EPDM 8 3/4" $2,261 *8" VITON 8 3/4" $3,624 Note: All fittings consist of (2) PVC flanges, (2) gaskets, designated number of polyethylene encapsulated Titanium bolts with gaskets, hole cut. Add 10% for thread by thread. (PVC) Encapsulated Hastelloy Bolts *Thread by thread not available. Socket by Socket DBL Flanged Fitting-(PVC) Bolted DBL Flanged Fitting-(PVC) Bolted w/epdm - Encapsulated Hastelloy Bolts w/viton - Encapsulated Hastelloy Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" EPDM 4 1/2" $905 1" VITON 4 1/2" $1, /2" EPDM 4 1/2" $ /2" VITON 4 1/2" $1,165 2" EPDM 4 5/8" $921 2" VITON 4 5/8" $1,182 3" EPDM 4 5/8" $967 3" VITON 4 5/8" $1,271 4" EPDM 8 5/8" $2,173 4" VITON 8 5/8" $2,580 *6" EPDM 8 3/4" $2,720 *6" VITON 8 3/4" $3,554 *8" EPDM 8 3/4" $2,913 *8" VITON 8 3/4" $4,284 Note: All fittings consist of (2) (PVC) flanges, (2) gaskets, designated number of polyethylene encapsulated Hastelloy bolts with gaskets, hole cut. Add 10% for thread by thread. *Thread by thread not available. 53

54 FITTINGS DOUBLE FLANGED FITTINGS - CPVC Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. (CPVC) Encapsulated SS Bolts Socket by Socket Double Flanged Fitting-(CPVC) Bolted Double Flanged Fitting-(CPVC) Bolted w/epdm - Encapsulated 316 Stainless Steel Bolts w/viton - Encapsulated 316 Stainless Steel Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" EPDM 4 1/2" $354 1" VITON 4 1/2" $ /2" EPDM 4 1/2" $ /2" VITON 4 1/2" $582 2" EPDM 4 5/8" $409 2" VITON 4 5/8" $625 3" EPDM 4 5/8" $536 3" VITON 4 5/8" $726 4" EPDM 8 5/8" $869 4" VITON 8 5/8" $1,285 *6" EPDM 8 3/4" $1,156 *6" VITON 8 3/4" $2,009 *8" EPDM 8 3/4" $1,733 *8" VITON 8 3/4" $2,965 Note: All fittings consist of (2) CPVC flanges, (2) gaskets, designated number of polyethylene encapsulated SS bolts with gaskets, hole cut. Add 10% for thread by thread. Max. size sidewall bolted fitting allowed. *Thread by thread not available. Tank PVC Diameter CPVC PP SS 18" 1" 2" 1 1/2" 22"-29" 1 1/2" 2" 2" 30" 2" 2" 2" 36"-45" 2" 2" 2" 48"-86" 3" 3" 4" 90"-102" 6" 3" 4" 120"-165" 8" 3" 4" 54

55 FITTINGS DOUBLE FLANGED FITTINGS - CPVC Note: Recommended minimum centerline height for fitting installation on vertical storage tanks is approximately 6 inches for October 1, 2017 tanks up to 2650 gallons and 9 inches for tanks 3000 gallons and above, depending on fitting size. Consult factory with questions. (CPVC) Encapsulated Titanium Bolts Socket by Socket Double Flanged Fitting-(CPVC) Bolted Double Flanged Fitting-(CPVC) Bolted w/viton - Encapsulated Titanium Bolts w/viton - Encapsulated Titanium Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" VITON 4 1/2" $852 4" VITON 8 5/8" $2,107 2" VITON 4 5/8" $1,048 *6" VITON 8 3/4" $3,153 3" VITON 4 5/8" $1,266 *8" VITON 8 3/4" $4,091 Note: All fittings consist of (2) CPVC flanges, (2) gaskets, designated number of polyethylene encapsulated Titanium bolts with gaskets, hole cut. Add 10% for thread by thread. *Thread by thread not available. (CPVC) Encapsulated Hastelloy Bolts Socket by Socket Double Flanged Fitting-(CPVC) Bolted Double Flanged Fitting-(CPVC) Bolted w/viton - Encapsulated Hastelloy Bolts w/viton - Encapsulated Hastelloy Bolts Part Gasket No. of Diam. List Part Gasket No. of Diam. List Size No. Material Bolts Bolts Price Size No. Material Bolts Bolts Price 1" VITON 4 1/2" $1,142 4" VITON 8 5/8" $2, /2" VITON 4 1/2" $1,191 *6" VITON 8 3/4" $3,801 2" VITON 4 5/8" $1,238 *8" VITON 8 3/4" $4,676 3" VITON 4 5/8" $1,340 Note: All fittings consist of (2) CPVC flanges, (2) gaskets, Max. size sidewall bolted fitting allowed. designated number of polyethylene encapsulated Tank PVC Hastelloy bolts with gaskets, hole cut. Diameter CPVC PP SS Add 10% for thread by thread. 18" 1" 2" 1 1/2" *Thread by thread not available. 22"-29" 1 1/2" 2" 2" 55 30" 2" 2" 2" 36"-45" 2" 2" 2" 48"-86" 3" 3" 4" 90"-102" 6" 3" 4" 120"-165" 8" 3" 4"

56 PRICE LIST All Prices F.O.B. Plant Issued October 1, COMMERCIAL TANKS Corporate Office: 6940 O Street, Suite 100 Lincoln, NE Phone: Fax: Other manufacturing locations: Chowchilla, California Marked Tree, Arkansas Philippi, West Virginia

57 COMMERCIAL TANKS All prices F.O.B. Plant Issued: October 1, 2017 WHAT'S THE DIFFERENCE BETWEEN INDUSTRIAL & COMMERCIAL TANKS? The Snyder Industrial (ASTM) Tank Price List is for engineered tanks. Industrial (ASTM) tanks are thicker walled tanks based on a 600 hoop stress calculation to determine the specific gravity rating. Industrial (ASTM) tanks are designed based on the criteria developed by the American Society for Testing and Materials (ASTM). Multiple fittings at many locations can be added to tanks listed in the Industrial (ASTM) Tank Price List. The Snyder Commercial Tanks Price List is for tanks in less severe chemical applications. These tanks are thinner walled based on higher hoop stress calculation to determine the specific gravity rating. (Note: hoop stress is a dividing factor in the calculation so the higher the hoop stress the thinner the wall of the tank). These tanks come with either no fittings (other than a manway) or a predetermined fitting package as outlined in the standard outlet specifications in the commercial price list. To determine which tanks you should quote (Industrial or Commercial) will depend on the application. Our published Chemical Resistance Recommendations chart outlines the design information (specific gravity and hoop stress) for several chemical applications. Another determining factor is fittings required on the tank. If the fittings required are other than the predetermined fitting package offered in the commercial price list, then the Industrial (ASTM) Tank line should be used. Part Number Key * Add the proper two or three digit code to the end of each tank part number to specify the correct material. NATURAL BLACK Specific Gravity Std Fitting Pkg Add digits Std Fitting Pkg Add digits **1.5 Yes 37 Yes 33 **1.5 No 137 No Yes 26 Yes No 126 No 134 **NOTE: 37 or 137 may be 1.9 where indicated. ORDER GUIDELINES How To Order: Tanks are available in Natural Color, or Black with a 10% up-charge. Only (1) installed fitting per tank at standard location of 90 clockwise from manway If a tank is ordered using the 137 or 126 three digit codes and no fitting is ordered, the tank will be supplied with no hole cuts or fittings. Outlets are PP or PE with EPDM gaskets For NSF Label, add $50 list use Part # Products have minor differences depending on F.O.B. point. See specification sheets for specific products. FOB Locations: All shipments are FOB factory. L = Lincoln, NE; M = Marked Tree, AR; P = Philippi, West Virginia; C = Chowchilla, CA; W = Washington Court House, OH

58 October 1,2017 COMMERCIAL TANKS VERTICAL STORAGE TANKS (VST) % of SUGGESTED LIST Snyder Tank Tank Tank Tank Cylinder Outlet Manway 53' HDLPE HDLPE Part No. Style Capacity F.O.B. Diameter Height Height Size Fill Truck C-- VST 70 C 23" 42" 39" 1" 8" N/A $ C-- VST 70 L 23" 41" 38" 1" 8" N/A $ C-- VST 100 L 35" 30" 28" 1" 8" N/A $ C-- VST 100 P 30" 41" 32" 1" 18" N/A $ C-- VST 130 C 29" 51" 44" 1" 8" N/A $ C-- VST 130 L 29" 49" 46" 1" 8" N/A $ C-- VST 150 P 30" 59" 50" 1" 18" N/A $ C-- VST 175 L 29" 66" 64" 1" 8" N/A $ C-- VST 200 L 35" 56" 54" 2" 8" N/A $ C-- VST 200 C 36" 53" 47" 2" 18" N/A $ C-- VST 210 P 36" 55" 46" 2" 18" N/A $ C-- VST 250 C 36" 64" 58" 2" 18" 0.02 N/A $ C-- VST 290 P 36" 72" 63" 2" 18" 0.02 N/A $ C-- VST 300 M 35" 80" 72" 2" 18" N/A $ S NST 300 M,P 66" length 49" 29" deep 1 1/4" 18" $973 N/A C-- VST 300 L 35" 82" 81" 2" 8" 0.03 N/A $ C-- VST 330 C 47" 50" 39" 2" 18" 0.02 N/A $ C-- VST 330 P 44" 58" 48" 2" 18" 0.02 N/A $ S NST 400 M,P 66" length 70" 29" deep 1 1/4" 18" $1,135 N/A C-- VST 550 C 48" 75" 76" 2" 18" N/A $ C-- VST 550 L,M,P 48" 75" 70" 2" 18" N/A $ C-- VST 550 L,C 64" 47" 38" 2" 18" N/A $ C-- VST 550 M,P 64" 46" 36" 2" 18" N/A $ C-- VST 560 M 65" 45" 36" 2" 8" 0.07 N/A $ C-- VST 750 C 72" 50" 40" 2" 18" 0.08 N/A $1, C-- VST 850 L,M,P 48" 117" 107" 2" 18" 0.05 N/A $1, C-- VST 1000 C 72" 65" 55" 2" 18" 0.09 N/A $1, C-- VST 1000 C 60" 89" 80" 2" 18" 0.05 N/A $1,287 58

59 October 1,2017 COMMERCIAL TANKS % of SUGGESTED LIST Snyder Tank Tank Tank Tank Cylinder Outlet Manway 53' HDLPE HDLPE Part No. Style Capacity F.O.B. Diameter Height Height Specs Fill Truck C-- VST 1100 L,M,P 64" 90" 79" 2" 18" N/A $1, C-- VST 1100 L,P,C 86" 55" 36" 2" 10" N/A $ C-- VST 1100 M 86" 55" 39" 2" 18" N/A $ C-- VST 1500 C 60" 137" 126" 2" 18" 0.1 N/A $1, C-- VST 1500 C 72" 93" 83" 2" 18" 0.17 N/A $1, C-- VST 1500 L,P,C 86" 72" 53" 2" 10" 0.1 N/A $1, C-- VST 1500 M 86" 72" 55" 2" 18" 0.1 N/A $1, C-- VST 1550 L,M,P 64" 124" 113" 2" 18" 0.2 N/A $1, C-- VST 2000 L,P 90" 88" 72" 2" 18" $1,848 $2, C-- VST 2000 M 90" 88" 72" 2" 18" $1,848 $2, C-- VST 2000 C 96" 84" 68" 2" 18" $1,848 $2, C-- VST 2100 P 102" 72" 55" 2" 18" $1,815 $2, C-- VST 2500 L,P 90" 107" 92" 2" 18" $2,131 $2, C-- VST 2500 M 90" 107" 92" 2" 18" $2,131 $2, C-- VST 2500 C 96" 98" 81" 2" 18" $2,131 $2, C-- VST 2650 M 102" 97" 79" 2" 18" $2,302 $2, C-- VST 3000 L,P 90" 127" 111" 3" 18" 0.2 $2,619 $2, C-- VST 3000 M 90" 127" 111" 3" 18" 0.2 $2,619 $2, C-- VST 3000 C 96" 111" 95" 3" 18" $2,619 $2, C-- VST 3000 L,P,C 102" 96" 88" 3" 18" $2,595 $2, C-- VST 3650 M 102" 126" 109" 3" 18" Flatbed $4,591 $5, C-- VST 4100 C 102" 124" 108" 3" 18" Flatbed $4,591 $5, C-- VST 4100 P 102" 130" 120" 3" 18" Flatbed $4,569 $5, C-- VST 4300 C 120" 104" 85" 3" 18" Wide $5,552 $6, C-- VST 4500 L,C 102" 142" 133" 3" 18" Flatbed $4,854 $5,533 59

60 October 1,2017 COMMERCIAL TANKS % of SUGGESTED LIST Snyder Tank Tank Tank Tank Cylinder Outlet Manway 53' HDLPE HDLPE Part No. Style Capacity F.O.B. Diameter Height Height Specs Fill Truck C-- VST 5000 P 102" 154" 138" 3" 18" Flatbed $6,192 $7, C-- VST 5000 C 120" 116" 96" 3" 18" Wide $7,266 $8, C-- VST 5300 C 102" 164" 148" 3" 18" Flatbed $6,581 $8, C-- VST 5400 C 143" 86" 63" 3" 18" 0.17 $6,134 $7, C-- VST 5400 C 142" 91" 66" 3" 18" Wide $6,503 $7, C-- VST 6000 L,P 120" 132" 118" 3" 18" Wide $6,784 $7, C-- VST 6000 L,P,C 102" 188" 179" 3" 18" Flatbed $7,245 $8, C-- VST 6200 M 120" 140" 128" 3" 18" Wide $7,299 $8, C-- VST 6500 C 120" 145" 126" 3" 18" Wide $7,299 $8, C-- VST 6900 L,P 120" 153" 140" 3" 18" Wide $7,299 $8, C-- VST 7650 L 142" 122" 105" 3" 18" Wide $8,574 $9, C-- VST 8150 L 120" 177" 164" 3" 18" Wide $9,828 $11, C-- VST 8300 C 120" 186" 166" 3" 18" Wide $9,828 $11, C-- VST 8900 L 120" 194" 180" 3" 18" Wide $11,837 $13, C-- VST 9800 L 120" 215" 201" 3" 18" Wide $12,277 $14, C-- VST 10,500 L,P 142" 169" 152" 3" 18" Wide $11,549 $13, C-- VST 10,500 C 143" 177" 152" 3" 18" Wide $11,549 $13, C-- VST 12,500 L 142" 198" 182" 3" 18" Wide $14,591 $16, C-- VST 15,000 W 165" 184" 155" 3" S.S. 24" Wide $17,518 $19, C-- VST 15,000 L 142" 234" 217" NO FTG 18" Wide $17,518 $19, C-- VST 16,500 L 142" 257" 240" NO FTG 18" Wide $27,965 $31, C-- VST 20,000 W 165" 242" 213" 3" S.S. 24" Wide $27,965 $31,968 Stress Reliever Tank Adapter Snyder Part No. Stress Reliever Tank Adapter - VSTs List Price " PP Stress Reliever (for connection to 2" PP bolted fitting) $ " PP Stress Reliever (for connection to 3" PP bolted fitting) $53 sales@snydernet.com You must use Industrial tanks and the Industrial price list for tanks where additional fittings are required. PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 60 Note: price is an addon price. The fitting and siphon are not included in pricing. Stress Reliever

61 October 1,2017 COMMERCIAL TANKS COMMERCIAL-Horizontal Tanks (HTL) F.O.B. LOCATIONS: L=LINCOLN, NE; M-MARKED TREE, AR; P=PHILIPPI, WV; C=CHOWCHILLA, CA % of Suggested Snyder Tank Tank Tank Tank Tank Outlet Manway 53' List Tank No. Style Capacity F.O.B. Diameter Length Height Size Fill Truck HDLPE C-- HLT 30 L,M,P,C 23" 20" 26" N/A 6" $ C-- HLT 60 L,P,C 23" 39" 26" 3/4" 6" $ C-- HLT 65 M 32" 44" 20" 3/4" 6" $ C-- HLT 125 L,P,C 30" 49" 35" 1 1/4" 10" $ C-- HLT 125 M 32" 44" 35" 1 1/4" 6" $ C-- HLT 225 M 38" 52" 42" 1 1/4" 6" $ C-- HLT 230 L,P,C 38" 52" 43" 1 1/4" 10" $ C-- HLT 300 L,P 38" 72" 43" 1 1/4" 10" $ C-- HLT 300 C 38" 68" 44" 1 1/4" 10" $ C-- HLT 335 M 44" 56" 49" 1 1/4" 6" $ C-- HLT 500 C 49" 72" 55" 2" 18" $ C-- HLT 525 L,P 48" 75" 53" 2" 10" $ C-- HLT 535 M 47" 78" 52" 2" 18" $842 * C--T HLT 730 L,P,C 54" 80" 58" 2" 10" $1, C-- HLT 750 L 46" 117" 48" 2" 18" 0.05 $1, C--T HLT 1025 L,P,C 48" 139" 50" 2" 18" $2, C--T HLT 1650 M,C 71" 142" 55" 3" 18" 0.25 $4, C-- HLT 1685 L 62" 159" 62" 3" 18" $3, C-- HLT 2000 L 62" 160" 70" 3" 18" $5, C--T HLT 2000 (1.5) P,C 84" 142" 55" 3" 18" $4, C--T HLT 2600 L,M,P,C 82" 155" 70" 3" 24" 0.25 $7, C--T HLT 3000 (1.5) L,M,P,C 92" 142" 76" 3" 18" 0.25 $7, C--T HLT 3400 (1.5) L 82" 155" 86" 3" 24" $11,889 * only (1) hoop required and provided NOTE: All HLT/HST tanks are 1.9 S.G. rated except Part Numbers C--,750000C--, C--. NOTE: The hoop assemblies are required and included in the above prices on 730 gallons and above T=Tank mold is transferred from plant to plant. Availability/lead time at plants dependent on available stock and mold location. 61

62 October 1,2017 COMMERCIAL TANKS RECTANGULAR (PCO) TANKS Snyder Tank Tank Tank Tank Tank Manway Suggested Part No. Style Capacity F.O.B. Length Width Height Fill List Price C-137 PCO 30 L,P,C 25" 19" 22 6" $ C-137 PCO 50 L,P,C 38 20" 22" 6" $ C-137 PCO 100 L,P,C " 10" $ C-137 PCO 150 L,P,C " 10" $ C-137 PCO 200 L,P,C 49" 37 39" 10" $ C-137 PCO 325 C " 18" $920 SPECIALTY TANKS Tank Tank Tank Tank Manway Suggested Part No. Desc. & Outlet Specs Capacity F.O.B. Length Width Height Fill List Price C-- L&G - 1/2" ID MOLDED 8 L,P,C 12" 16" 15" 6" $ C-- L&G - 1/2" ID MOLDED 12 L,P,C 12" 16" 19" 6" $ C-- SADDLE - no outlet 15 L,C 14" 32" 13" 6" $ C-- SADDLE - no outlet 25 L,C 18" 36" 16" 6" $ C-- PICKUP - 2" outlet 150 P 54" 54" 26" 10" $ C-- PICKUP - 2" outlet 300 P 64" 64" 33" 10" $ C-- PICKUP - 2" outlet 450 P 64" 64" 48" 10" $660 HORIZONTAL TANK BANDS, HOOP ASSEMBLIES Stainless Tank Tank Hoop Tank Tank Hoop Steel Bands Style Size F.O.B. Bands Assembly Style Size F.O.B. Assembly HLT 30 L,M,P,C $ HLT 300 X 38 C $ HLT 60 L,M,P,C $ HLT 500 X 49 C $ HLT 125 L,P,C $ HLT 525 X 48 L,M,P $ HLT 230 L,P,C $ HLT 730 X 54 L,M,C $174 each HLT 300 L,M,P $78 HOOP ASSEMBLIES REQUIRED FOR 730 GALLONS AND HLT 525 L,M,P $94 ABOVE INCLUDED IN TANK PRICING HLT 730 L $118 OPTIONAL FOR LINCOLN 300, 500, & 525 LEG TANKS. Need two bands per tank. HOOP PRICE NOT INCLUDED IN TANK PRICING. Stainless Steel Bands (Optional) 2 Bands and 1 J-Bolt Package needed per tank. sales@snydernet.com # J Bolt Package = $37.00 each. See specification sheets for specific products. 62

63 Snyder Manufacturing Locations Tank Drawings available online at Tank Specifications available at Corporate Office: 6940 O Street, Suite 100 Lincoln, NE Phone: Fax: Other manufacturing locations: Chowchilla, California Philippi, West Virginia Marked Tree, Arkansas Mancelona, MI West Chicago, IL Bensenville, IL sales@snydernet.com