Ball Sector Valve 4040

Transcription

1 D 25 up to D 300 D 25 up to D300 High Kvs-values up to 3840 xcellent control characteristics Suitable for abrasive media asily exchangeable seat ring Low maintenance Actuators can be easily fitted fficient and easy to install optional Volume booster Type 4090 (from D50) in order to reduce the response time optional with face to face dimension acc. ASI ISA Technical Information Valve Packing tested according to TA-Luft as defined in DI ISO and VDI 2440 Design D 25 - D 250 flangeless wafertype D 300 flange connection ominal sizes D 25 up to D 300 Body material cast parts.4408 (C8) turned parts.4404 (36L) aterial of the bearing shaft.422 Bearing material high temperature plain bearing (Iglidur Z) Connection to the actuator mounting kit DI/ISO 52 ominal pressure D 25 - D 50 P40 (for flanges P 0 - P 40), ASI300, ASI50 D 80 - D00 P25 (for flanges P 0 - P 25), ASI50 D 50 - D 300 P6 (for flanges P 0 - P 6), ASI50 luid Temperature -40 C up to +220 C according to the sealings Ambient temperature -40 C up to +80 C according to the acuator special version on request Characteristic almost equal percentage Rangeability 300: Schubert & Salzer Control Systems GmbH, Bunsenstr. 38, Ingolstadt, Tel: +49 (0) , ax: +49 (0) info.cs@schubert-salzer.com,

2 Valve sizes, Kvs-Values, Torques D Kvs hole rotation angle max. max. req. torque [m] mounting kit mm nominal* press. nomial press. nomial on/off- control DI/ISO DI ASI operation operation series series % 2, P40 ASI /SW 05/SW P40 ASI /SW 05/SW % P40 ASI /SW4 07/SW P40 ASI /SW4 07/SW P40 ASI /SW4 07/SW P25 ASI /SW7 0/SW P25 ASI /SW7 0/SW P6 ASI /SW22 2/SW P6 ASI /SW27 4/SW P6 ASI /SW27 4/SW P6 ASI /SW36 6/SW46 * All Valves can be rotated 90 when actuated. Though for valves with reduced bore holes a smaler angle of rotation is sufficient. Valve seat combinations Seat ring Ball sector Leakage min. temp [ C]* PT stainless steel polished or hard chrome plated or lapped 5x0-7 of max. Kvs -40 up to +70 C PK stainless steel polished or hard chrome plated or lapped 5x0-7 of max. Kvs -40 up to +220 C Stellit stainless steel, hard chrome plated and lapped Class IV-S acc. 349 (IC 534-4) 5x0-6 of max. Kvs -40 up to +220 C PT stainless steel, hard chrome plated and lapped Class VI acc. 349 (IC 534-4) -40 up to +70 C Stellit stainless steel, hard chrome plated and lapped, seat holding ring hard chrome plated * Please note the restrictions of the o-ring material! 5x0-6 of max. Kvs -40 up to +220 C Shaft seals (o-ring) min. temp [ C] max. temp [ C] comment Viton (Standard) PD suitable for steam BR (P700) K (Perlast/Kalrez) suitable for steam special material on request Actuators Actuators for mounting according DI/ISO52, pilot pressure 5-6 bar (for less than 5 bar pilot pressure, please inform us) Working pressure max. ominal size maximum differential pressure (delta p) seat ring PT seat ring PK seat ring Stellit D up to 80 C 20 C 70 C up to 80 C 20 C 70 C 220 C up to 80 C 70 C 220 C bar bar bar bar bar bar bar bar bar bar /5

3 Ordering umber System ominal Size e.g. D 25 = 025 Article valve repair-kit seat kit Connection flangeless design according DI 092- flangeless design according AS B 6.5, ASI 50 flangeless design according AS B 6.5, ASI 300 flangeless design for flange AS B 6.5, ASI 50, fitting length acc. ASI ISA flangeless design for flange AS B 6.5, ASI 300, fitting length acc. ASI ISA Body material stainless steel.4408 (C8) /.4404 aterial combination seat ring: PT; ball sector:.4408, polished seat ring: PT; ball sector:.4408, hard chrome plated seat ring: Stellit; ball sector:.4408, hard chrome plated and lapped seat ring: PT; ball sector:.4408, hard chrome pated and lapped seat ring: TCAPK; ball sector:.4408, hard chrome plated Seal combination all seals (part 3-6) from VITO, medium temperature: -5 C to +200 all seals (part 3-6) from K (Perlast/Kalrez), medium temperature: -5 C to +220 C all seals (part 3-6) from PD, medium temperature: -30 C to +40 C all seals (part 3-6) from BR(P700), medium temperature: -40 C to +00 C Actuator without mounting kit, without actuator without actuator, with standard mounting kit according DI/ISO 52 pneumatic quater-turn actuator (Air Torque) with mounting kit according DI/ISO 52 hand lever Safety position: without single acting, spring to close double acting, without safety position single acting, spring to open ounting standard PT thread connection in stainless steel pneumatical connection PT, cable screw metrical 2 x 6x,5 PT-thread Ordering umber: 4040/ Z Positioner without - without positoner, with mounting kit according VDI/VD 3845 for positioners 0 i/p-positioner SIPART PS2 2 i/p-positioner PV Typ P5 8 digital positioner Schubert & Salzer Type 8049, 4-wire L digital positioner Schubert & Salzer Type 8049, 2-wire R Additional specifications for the positioner without - positioner single acting positioner double acting 2 positioner single acting with gauge 3 positioner double acting with gauge 4 Positioner settings standard - double acting 20-4 ma (20mA closed, 4mA open) single acting 20-4 ma (inverse function, safety position at 20mA) 2 Kvs-value 00% - 50% xxx V R D A B P A D 0 T H K 3/5

4 Dimensions with AirTorque actuator (designed for a pilot pressure of 5-6 bar) L4 L3 C D L H O B O A G L2 H3 2 2 (ASI ISA ) single acting double acting D A B C D G L weight weight L2 L3 L4 H L2 L3 L4 H (kg) (kg) (5) , , , (25) ,5 56, , , ,5 56, , , , ,5 56,8 282, , , , ,5 9,5 43 4, , , ,5 73, ,5 9, , , , ,9 D ASI ISA Dimensions for D300 on request. Dimension in mm 4/5

5 Dimensions without actuator (with mounting kit ISO 52) C D L O B O A G d D 3 SW 2 2 (ASI ISA ) D A B C D G L d D3 SW DI/ISO weight 52 (kg) (5) , , (25) , , , , , , , , , , D ASI ISA Dimensions for D300 on request. Dimension in mm Text and pictures are not binding. We reserve the right, to alter the equipment. Data sheet 4040e/Version: /5