Card Edge Connectors Catalog Issued 7-03

Transcription

1 Catalog Issued 7-03

2 Introduction This catalog contains product descriptions of MP Card Edge Connectors. These connectors are presented in three groups: Solder Type Board-to- Board, Press-fit Board-to- Board, and Wire-to-Board connectors. To assist you in the selection of the appropriate connector for your application, a selection guide is provided at the beginning of each section. See the Table of Contents on the following page for the exact location. comprehensive description and features of a particular printed circuit board connector family are provided at the beginning of that section. Various technical documents are referenced in the connector family sections and are listed and described at the rear of this catalog. The Tyco Electronics products presented in this catalog are designed and manufactured according to the highest possible standards of quality and craftsmanship. They offer optimum reliability at the lowest possible cost. Need more information? Call Technical Support at the numbers listed at the bottom of the catalog pages. Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with: Technical Support Catalogs Technical Documents Product Samples Tyco Electronics uthorized Distributor Locations Dimensioning: Dimensions are in inches and millimeters unless specified otherwise. Values in brackets are metric equivalents. Metric symbols used are: m (meter) mm (millimeter) mm2 (square millimeter) kg (kilogram) C (Celsius) N (newton) Note: Dimensions in this catalog are for reference purposes only. Customer drawings are available upon request. Copyright 1992, 1996 and 2002 by Tyco Electronics. ll Rights Reserved. MP, CTION PIN, MP-DURGOLD, MP-LEF, MP-O-LECTRIC, MP-O-MTIC, MPOMTOR, MP PCE, CERTI-CRIMP, DUO-TYNE, ECONOMTE, TELEDENSITY, and TYCO are trademarks. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. Produced under a Quality Management System certified to ISO 9001 copy of the certificate is available upon request 2

3 Table of Contents Solder Type Board-to-Board Connectors Introduction 2 Selection Guide 4-6 Standard Edge Series Connectors Standard Edge.050 PCI Card Edge Connectors 7-10 Standard Edge.050 Series Connectors Standard Edge II Connectors Cantilever Beam Dip Solder Tails Overview 28 " [2.54] Centerline " [3.18] Centerline " [3.96] Centerline Modified Bellows Contact Overview 41 " [2.54] Centerline " [3.18] Centerline " [3.96] Centerline Polarization Keys 57 Standard Daughter Card Layout 57 Low Profile Connectors Twin Leaf Mother Board Connectors Rotary Cam ZIF Connectors Linear ZIF Connectors Press-Fit Board-to-Board Connectors CTION PIN Press-Fit Contacts 97 MP PCE Connectors TELEDENSITY Connectors ECONOMTE Connectors Cantilever Beam Press-Fit Connectors Overview " [1.27] High Density " [2.54] Centerline " [3.18] Centerline " [3.96] Centerline pplication Tooling Wire-to-Board Connectors Introduction 152 Selection Guide 153 Crimp Snap Twin Leaf Connectors MP-LEF Connectors High Current Connectors DUO-TYNE Flag Connectors Printed Circuit Board Connector Hood ssemblies pplication Tooling 184,185 Technical Documents 186,187 Part Number Index Tyco Electronics Related Product Information 202 3

4 Selection Guide, Board-to-Board Connectors Introduction Board-to-board (mother/ daughter board) connectors are ideally suited to backplane wiring or any other application requiring the circuit connection of one printed circuit board to another. Designed to shorten manufacturing time and reduce applied costs, these one-step, pre-assembled connectors are ready for mounting and mass insertion. Many of the connectors are available with the proven and reliable CTION PIN contact. This unique contact has superior electrical and physical characteristics that are top of the line in the industry. Board-to-board connectors come in a range of contact centerline spacings of.050 [1.27] to.156 [3.96]. wide range of dual position sizes and post styles are available. One family of connectors features zero insertion force of the daughter board, along with a choice of actuating devices. variety of housing and contact materials further expands the choice of connectors available to meet many application requirements. To help in choosing a connector for your application, a Selection Guide is provided on pages 4 through 6. Standard Edge.050 Series PCI Connectors (Pages 7-10) Standard Edge.050 Series Connectors (Pages 11-14) Standard Edge II Connectors ( and Centerline) (Pages 15-27).350 [8.89].368 [9.35].610 [15.49].300 [7.62].170±.020 [4.32±0.51].300 [7.62].170±.020 [4.32±0.51].610 [15.49].155 [3.94].315 [8.00].610 [15.49] Centerlines.050 [1.27] X X [2.54] X [3.18] X.150 [3.81].156 [3.96] 4 Tail Styles Solder X X X Right-ngle Solder X Wrap-Type X Card Extender X Solder Eyelet Press-Fit Surface-Mount

5 Selection Guide, Board-to-Board Connectors (Continued) Standard Edge II Connectors (.150 Centerline) (Pages 15-27) Cantilever Beam Connectors Standard Housing (Pages 28-40) Cantilever Beam Connectors Scoop Housing (Pages 28-40).365 [9.27].135±.020 [3.43±0.51].200 [.508] [ ].045 [1.14].015 [0.33].200±.020 [5.08±0.51].015 [0.41] X.008 [.203].610 [15.49].370 [9.40].145 [3.68].020±.010 [.51±.25].300 [7.62].705 [17.91].390 [9.91].054 to.071 [1.37 to 1.80].395 or.510 [10.03 or 12.95] Centerlines.050 [1.27].0625 [1.588] X X [2.54] X X [3.18].150 [3.81] X X.156 [3.96] Tail Styles X X X Solder Right-ngle Solder Wrap-Type Card Extender Solder Eyelet X X Press-Fit Surface-Mount Modified Bellows Connector (Pages 41-56).610 [15.49].368 [9.35] [ ].300 [7.62] [3.18] Low Profile Connectors (Pages 58-63).437 [11.10].460 [11.68] Twin Leaf Mother Board Connectors (Pages 64-72).610 [15.49].150 [3.81].400 [10.16].025 [.63].200 [5.08].165 [4.19] Centerlines.050 [1.27] X X [2.54] X X X [3.18] X.150 [3.81] X X X.156 [3.96].235 [5.97] Tail Styles X X X Solder X Right-ngle Solder X Wrap-Type Card Extender X Solder Eyelet Press-Fit Surface-Mount 5

6 Selection Guide, Board-to-Board Connectors (Continued).848 [21.54].150 [3.81].598 [15.19] Rotary Cam ZIF Connectors (Pages 73-82).440 [11.18].845 [21.46].815 [20.70].140 [3.56] Linear ZIF Connectors (Pages 83-96).475 [12.07].450 [11.43].490 [12.45].460 [11.68].370 [9.40].345 [8.76] MP PCE Connectors, Card Scoop Housing (Pages ).234 [5.94].130 [3.30] x.200 =.390 [9.91] x =.420 [10.67] x.200 =.420 [10.67].645 [16.38] 6 Centerlines.050 [1.27].0625 [1.588] [2.54] X X X [3.18] X X X.150 [3.81].156 [3.96] X Tail Styles Solder X X Right-ngle Solder X Wrap-Type X X X Card Extender Solder Eyelet Press-Fit X X Surface-Mount Centerlines.050 [1.27] X.0625 [1.588] [2.54] X X [3.18] X.150 [3.81].156 [3.96] X X Tail Styles MP PCE Connectors, Standard Housing (Pages ).234 [5.94].130 [3.30] x =.380 [9.65] x.200 =.360 [9.14] x.250 =.410 [10.41].156 x.200 =.360 [9.14].545 [13.84] ECONOMTE Connectors (Pages ).181 [4.60].415 [10.54].545 [13.84] High Density Press Fit Connector For.093 Cards (Pages ).400 [10.16].066 [1.68].610 [15.49] [10.69] [11.71] Solder Right-ngle Solder Wrap-Type X Card Extender Solder Eyelet Press-Fit X X X Surface-Mount

7 (Solder Type Board-to-Board) Standard Edge.050 Series PCI Card Edge Connectors Product Facts High density.050 [1.27] centerline contact spacing Easy mating of high circuit count daughter boards Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Connectors that support PCI expansion cards are derived from those on the MicroChannel rchitecture (MC) bus. The MC connectors are well defined and have proven value and reliability. There are four connectors that can be used depending upon the PCI implementation. The differences between these connectors are 32 bit and 64 bit, and the 5 volt and 3.3 volt signaling environments. PCI-X is a version of PCI at 133 MHz which is under development and employs standard PCI connectors. PCI-X is limited to 1 slot versus 4 slots of PCI. key differentiates the signaling environment voltages. The same physical connector is used for the 32 bit signaling environments. In one orientation, the key accepts 5 volt boards. When rotated 180, the connector accepts 3.3 volt signaling boards. The pin numbering of the connector changes for the different signaling environments to maintain the same relative position of signals on the connector. Performance Specifications: Durability Tested to 100 mating cycles Mating Force 8 oz [2.22 N] max. per contact pair Unmating Force.5 oz [0.14 N] min. per contact pair Contact Resistance 20 milliohms max. (initial) 30 milliohms max. (final) Insulation Resistance 1000 megohms min. Dielectric Withstanding Voltage 500 VC (at sea level) Capacitance 2 picofarads max. Current Rating 1 ampere max. Voltage Rating 203 VC Thermal Shock 55 C to +85 C for 5 cycles Mixed Flowing Gas Class II with mated board for 20 days Technical Documents: Product Specification pplication Specification Qualification Test Report

8 (Solder Type Board-to-Board) Standard Edge.050 Series PCI Card Edge Connectors 64 Bit, 5 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns Material and Finish: Housing High temperature thermoplastic 94V-0 rated, white Contacts Phosphor bronze, plated as follows: Plating B Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Plating C Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Related Product Data: Performance Specifications page 7 W ±.010 [±0.25] Typ. L L See Note Spaces at [1.27] [128.02].035 [0.89] (2 Plcs.).350 [8.89].610 [15.49].060 [1.52] 35 (2 Plcs.).075 [1.90].150 (2 Plcs.) [3.81] Typ Spaces.050 at [1.27] 31 Spaces.050 at [1.27] [3.81] (2 Plcs.) Section L-L.300 [7.62].170±.020 [4.32±0.51].050 [1.27] Solder Tail C L (2 Plcs.) Technical Documents: Product Specification pplication Specification Metal Holddowns L.035 [0.89] (2 Plcs.) 35 (2 Plcs.) Through Hole.170±.020 [4.32±0.51] Surface Mount W ±.010 [±0.25] Typ. L 48 Spaces at.050 [1.27].075 [1.90] (2 Plcs.) 10 Spaces.050 at [1.27] See Note..150 [3.81] 31 Spaces.050 at [1.27].610 [15.49].060 [1.52] Typ..150 [3.81] (2 Plcs.).300 [7.62].078 [1.98] Ref..003 [.076].050 [1.27] Solder (2 Plcs.) Tail C L Section L-L.180 [4.57].300 [7.62] [ ].180 [4.57] Part Numbers W Contact 5 Volt (Post Length) Finish 3 Plastic 3 Metal Pylons Holddowns Plating B Plating C Surface Mount Plating C Plating C Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 8

9 (Solder Type Board-to-Board) Standard Edge.050 Series PCI Card Edge Connectors 32 Bit, 3.3 and 5 Volt Signaling Plastic Pylons 60 Dual Positions with 2 Plastic Pylons or 2 Metal Holddowns [84.84].350 [8.89] Material and Finish: Housing Y High temperature thermoplastic 94V-0 rated, white Housing Z Nylon 6/6, white Contacts Phosphor bronze, plated as follows: Plating Duplex plated gold flash in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Plating B Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Plating C Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel W ±.010 [±0.25] Typ..075 [1.90] (2 Plcs.) 10 Spaces.050 at [1.27] L L 48 Spaces at.050 [1.27].035 [0.89] (2 Plcs.) See Note. 35 (2 Plcs.).610 [15.49].060 [1.52] Typ..150 [3.81] (2 Plcs.).170±.020 [4.32±0.51] Section L-L.300 [7.62].050 [1.27] Solder Tail C L (2 Plcs.) Related Product Data: Performance Specifications page 7 Metal Holddowns L.035 [0.89] (2 Plcs.) 35 (2 Plcs.) Through Hole.170±.020 [4.32±0.51] Surface Mount Technical Documents: Product Specification pplication Specification W ±.010 [±0.25] Typ..075 [1.90] (2 Plcs.) 10 Spaces.050 at [1.27] L 48 Spaces at See Note..050 [1.27].610 [15.49].060 [1.52] Typ..150 [3.81] (2 Plcs.).300 [7.62].078 [1.98].003 Ref. [.076].050 [1.27] Solder (2 Plcs.) Tail C L Section L-L.180 [4.57].300 [7.62] [ ].180 [4.57] Part Numbers W Housing Contact (Post Length) Material Finish 2 Plastic 2 Metal Pylons Holddowns Plating Y Plating B Plating C Plating Z 3.00 Plating B Surface Mount Y Plating C Y Plating C Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 9

10 (Solder Type Board-to-Board) Standard Edge.050 Series PCI Card Edge Connectors 64 Bit, 3.3 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns [128.02].350 [8.89] Material and Finish: Housing High temperature thermoplastic 94V-0 rated, white Contacts Phosphor bronze, plated as follows: Plating B Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Plating C Duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel W ±.010 [±0.25] Typ..075 [1.90] (2 Plcs.) 10 Spaces.050 at [1.27] See Note..150 [3.81] Spaces at [1.27] L L.035 [0.89] (2 Plcs.) 31 Spaces.050 at [1.27].610 [15.49].060 [1.52] Typ. 35 (2 Plcs.).150 [3.81] (2 Plcs.).170±.020 [4.32 ±0.51 ] Section L-L.300 [7.62].050 [1.27] Solder Tail C L (2 Plcs.) Related Product Data: Performance Specifications page 7 Technical Documents: Product Specification pplication Specification Metal Holddowns W ±.010 [±0.25] Typ. L L 10 Spaces at.050 [1.27] See Note..075 [1.90] (2 Plcs.).150 [3.81] Spaces at [1.27].035 [0.89] (2 Plcs.) 31 Spaces at.050 [1.27].610 [15.49].060 [1.52] Typ. 35 (2 Plcs.).150 [3.81] (2 Plcs.) Through Hole.170±.020 [4.32 ±0.51 ].300 [7.62].078 [1.98].003 Ref. [.076].050 [1.27] Solder (2 Plcs.) Tail C L Section L-L Surface Mount.180 [4.57].300 [7.62] [ ].180 [4.57] Part Numbers W Contact 3.3 Volt (Post Length) Finish 3 Plastic 3 Metal Pylons Holddowns Plating B Plating C Surface Mount Plating C Plating C Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 10

11 (Solder Type Board-to-Board) Standard Edge.050 Series Connectors Product Facts High density.050 [1.27] centerline spacing of contacts Easy mating of high-circuit count daughter boards Compatible with infrared reflow (IR) soldering techniques Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Recognized under the Component Program of Underwriter Laboratories Inc. File No. E28476 Certified by Canadian Standards ssociation, File No. LR 7189 Performance Specifications: Contact Current Rating* 1 ampere Termination Resistance 20 milliohms max. (initial) 30 milliohms max. (final) Dielectric Withstanding Voltage 500 VC min. Insulation Resistance 1000 megohms min. Mating Force.5 oz. [0.14 N] per contact pair Unmating Force 1 oz. [0.3 N] per contact pair Durability (Tested to) 100 mating cycles pplication Temperature +215 C for 120 seconds max. Temperature Range 55 C to +85 C *Consult Tyco Electronicsengineering when paralleling contacts for power applications. The need to conserve space and pack more function into a given area has demanded that.050 [1.27] centerline spacing become a reality. MP Standard Edge.050 Series connectors are the ideal vehicle for mother/daughter board applications requiring this real estate. These rugged connectors have two rows of contacts on.050 [1.27] centerlines. Polarizing webs provide positive board-to-connector registration, while insertion force allows even high circuit-count daughter boards to mate easily. The connectors accept.054 to.070 [1.37 to 1.78] thick daughter boards and feature an overstress protected contact design. MP Standard Edge.050 Series connectors are ideal for fast automated robotic assembly with registration features and dimensional tolerancing for more accurate pickup and placement, and are packaged in roboticscompatible trays. Plastic guide posts or metal holddowns align the connector with the mother board and retain it for soldering. To make circuit routing easy, connector solder posts are arranged in a four-row [2.54] staggered grid. Hightemperature tolerant materials promote that these connectors withstand infrared reflow (IR) soldering, while standoffs ease flux cleaning. High Density for DataBus pplications 11

12 (Solder Type Board-to-Board) Standard Edge.050 Series Connectors Configuration; 1 Key 2 Plastic Pylons.350 [8.89] Material and Finish: Housing High temperature thermoplastic, brown Contacts Phosphor bronze, duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Related Product Data: Performance Specifications page 11 Technical Documents: Product Specification pplication Specification W (Post Length).075 [1.90] (2 Plcs.) Spaces.050 at [1.27] L L C.016 [0.41] Typ. B Spaces.050 at [1.27].035 [0.89] (2 Plcs.) 35 (2 Plcs.).610 [15.49].060 [1.52] Typ..300 [7.62].170±.020 [4.32±0.51].150 [3.81] (2 Plcs.).050 [1.27] (2 Plcs.) Section L-L.012 [0.30] Typ. No. of Dimensions W PC Board Dual (Post Hole Positions B C Length) Layout Connector Part Numbers B B B B B C Connector used for VLLocal Bus and MC Bus applications. 2 Connector used for MC Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. [3.18] post length is available, consult Tyco Electronics. 12

13 (Solder Type Board-to-Board) Standard Edge.050 Series Connectors Configuration; 1 Key 2 Plastic Pylons Material and Finish: Housing High temperature thermoplastic, brown Contacts Phosphor bronze, duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Related Product Data: Performance Specifications page 11 Technical Documents: Product Specification pplication Specification W (Post Length).075 [1.90] (2 Plcs.) Spaces.050 at [1.27] D B Spaces.050 at [1.27] L L.150 [3.81].035 [0.89] (2 Plcs.) C Spaces.050 at [1.27].350 [8.89] 35 (2 Plcs.).610 [15.49].060 [1.52] Typ..170±.020 [4.32±0.51].300 [7.62].150 [3.81] (2 Plcs.).050 [1.27] (2 Plcs.) Section L-L.012 [0.30] Typ..096 Dia. Max. [2.44].016 [0.41] Typ. No. of Dimensions W PC Board Dual (Post Hole Connector Positions B C D Length) Layout Part Numbers * *Connectors used for MC Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. [3.18] post length is available, consult Tyco Electronics. 13

14 (Solder Type Board-to-Board) Standard Edge.050 Series Connectors Configuration; 1 Key/1 Web 3 Metal Holddowns.350 [8.89] 120 Dual Positions Material and Finish: Housing High temperature thermoplastic, brown Holddowns Brass, plated [ ] min. tin-lead over [ ] min. nickel Contacts Phosphor bronze, duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel Related Product Data: Performance Specifications page 11 W (Post Length).075 [1.90] (2 Plcs.) 10Spaces.050 at [1.27] [163.58].150 [3.81] 44Spaces.050 at [1.27] L L.035 [0.89] (2 Plcs.) 63 Spaces.050 at [1.27] 35 (2 Plcs.).610 [15.49].060 Typ. [1.52].150 [3.81] (2 Plcs.) Section L-L.300 [7.62].170 ±.020 [4.32 ±0.51 ].180 [4.57].050 Solder Tail C [1.27] L (2 Plcs.) Technical Documents: Product Specification pplication Specification No. of W Connector Dual (Post Part Positions Length) Numbers Note: Other connector sizes can be made available, consult Tyco Electronics. Configuration; End Key Material and Finish: Housing High temperature thermoplastic, brown Contacts Phosphor bronze, duplex plated [ ] min. gold in contact area, [ ] min. tin-lead on solder tails, with entire contact underplated [ ] min. nickel L B.035 [0.89].350 [8.89] [2.44] Dia. Max..170±.020 [4.32±0.51].016 [0.41] Typ..099 [2.52] Max. Related Product Data: Performance Specifications page [15.49].300 [7.62] Technical Documents: Product Specification pplication Specification Post Length L.075 [1.90] Spaces.050 at [1.27].060 [1.52] Typ..150 [3.81] (2 Plcs.) Section L-L.012 [0.30] Typ..050 [1.27] (2 Plcs.) No. of Dimensions Dual Post Connector Positions B C D Length Part Numbers Note: Other connector sizes can be made available, consult Tyco Electronics. 14

15 Standard Edge II Connectors Product Facts Maximum number of dual positions [2.54] Centerlines-70, [3.18] Centerlines-50,.150 [3.81] Centerlines-31 Selective gold plating of contacts for high performance at low cost.025 [0.64] square solid posts meet standard wraptype specifications For flow solder applications Glass-filled polyester housing is 94V-0 rated ccepts double sided PC boards, [ ] thick Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards ssociation, File No. LR 7189 Performance Specifications Contact Rating*: 3 amperes continuous (UL and CS) Contact Resistance: 10 milliohms max. Operating Temperature: 55 C to +85 C Voltage Rating (Sea Level): [2.54] centerline 1000 VC (test) [3.18] centerline 1500 VC (test).150 [3.81] centerline 1500 VC (test) Insulation Resistance: 5000 megohms min., after exposure to humidity Vibration Tolerance: 10 to 500 hertz Contact Engagement Force: 12 oz [3.3 N] average per pair with.062 [1.57] PC board Contact Separation Force: 2 oz [0.6 N] average per pair with.062 [1.57] PC board MP Standard Edge II Connectors provide high reliability and economy in packages compatible with industry standards for double sided printed circuit boards. Tyco Electronics offers Standard Edge II Connectors with or without mounting ears, for rack mounting and soldering. Contacts are arranged on [2.54] centers, [3.18] centers,.150 [3.81] centers,.200 [5.08] row-to-row; and.250 [6.35] row-to-row. Right-angle connectors are also available with contacts arranged on [2.54] centers,.150 [3.81] row-to-row or.200 [5.08] row-to-row. Card extenders with contacts on [2.54] and [3.18] centers also are available. Precision formed phosphor bronze contacts are selectively gold plated. Phosphor bronze has excellent strength characteristics which help the connector absorb load deflection movement of a PC board while maintaining sufficient contact force for good electrical connection. Bifurcated cantilever beam contacts provide redundant contact. Humidity Tolerance: 90%-95% for 96 hours *Consult Tyco Electronics engineering when paralleling contacts for power applications. 15

16 Standard Edge II Connectors Styles [2.54] and [3.18] Centerline Solder Posts without Mounting Ears Pages 17 and 18 [2.54] Centerline Right-ngle Posts with Low and No Mounting Ears Page 23 [2.54] and [3.18] Centerline Solder Posts with Low and Mid-High Mounting Ears Page 20 [2.54] and [3.18] Centerline Wrap-Type Posts with Mid-High Mounting Ears Page 21 [2.54] Centerline Solder Posts with Board Retention Feature, without Mounting Ears Page 24 [2.54] and [3.18] Centerline Card Extenders Page [3.81] Centerline Solder Posts (with Board Retention Feature), without Mounting Ears Page 19 16

17 Standard Edge II Card Edge Connectors [2.54] Centerline, Vertical Solder Posts, Without Mounting Ears.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp. Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, duplex plated as follows: Plating [ ] gold in contact area, tin on posts, with entire contact nickel underplated Plating B [ ] gold in contact area, tin on posts, with entire contact nickel underplated Plating C Gold flash in contact area, tin on posts, with entire contact nickel underplated Technical Documents: [2.54].610 [15.49] [2.54] Typ. D C** B.368 [9.35].550 [13.97].060 [1.52].141/.153 [3.58/3.88] Retention Feature (Open End Card Slot) ccepts.054/.070 [1.37/1.77] PC Board.191 [4.85].295 [7.49].155 [3.94] Post Length Product Specification Intercontact Keying Plug Material: Natural color polyester Part Number ( [2.54] Centerline) No. of Dimensions Post Part Numbers Dual Positions B C** D Length* Plating Plating B Plating C Open End **Metric equivalent for post lengths are = 3.18;.187 = **C dimension is card slot length. 1 Connectors with Retention Feature. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 17

18 Standard Edge II Connectors (Continued) [3.18] Centerline, Vertical Solder Posts, Without Mounting Ears.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp. Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated with [ ] gold in contact area, tin on posts, with entire contact nickel underplated [3.18] D C**.368 [9.35].191/.203 [4.85/5.16] Retention Feature Related Product Data: Performance Specifications page 15 PC Board Hole Layout page 26 PC Board Edge Pattern page 27 Special pplication page [15.49].550 [13.97] ccepts.054/.070 [1.37/1.77] PC Board.155 [3.94].295 [7.49] Technical Documents: (pages 186, 187): Product Specification [3.18] B.060 [1.52].241 [6.11] Post Length Intercontact Keying Plug Material: Natural color polyester Part No ( [3.18] Centerline) No. of Dimensions Dual Post Positions B C** D Length* Part Numbers **Metric equivalent for post lengths are = [3.18];.187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. Note: Other connector sizes can be made available, consult Tyco Electronics. 18

19 Standard Edge II Connectors (Continued).150 [3.81] Centerline, Vertical Solder Posts, Retention Feature, Without Mounting Ears Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated with [ ] gold in contact area, tin on posts, with entire contact nickel underplated Inter-Contact Keying Slot B ±.010 [±0.25] Card Slot ccepts [ ] Printed Circuit Board [10.97] [9.27].035±.020 [3.430±0.51].200 [5.08].045 [1.14] Contact rea.015 [0.38].080 [.203] Lead in.200±.020 rea [5.08±0.51].016 [0.41].020 [0.51] Related Product Data: Performance Specifications page 15 PC Board Hole Layout page 26 PC Board Edge Pattern page 27 Special pplication page [0.61].020 [0.51] Spaces at.150 = Dim Ref. [3.81].025 [0.63].600 [15.21] [ ] No. of Dimensions Retention Post Part Dual Location Numbers Positions B Length* , , , , , ,53-56 **Metric equivalent for post length is.135 = [3.43] **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics

20 Standard Edge II Connectors (Continued) [2.54] and [3.18] Centerline, Vertical Solder Posts, Low and Mid-High Mounting Ears.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp..150 [3.81] Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated with [ ] gold in contact area, tin on posts, with entire contact nickel underplated Related Product Data: Performance Specifications page 15 PC Board Hole Layout page 26 PC Board Edge Pattern page 27 Special pplication page [9.35].610 [15.49].250 [6.35] H G D C** F B E Low Mounting Ears.128 [3.25] Dia..360 [9.14].060 [1.52].300 [7.62].550 [13.97] ccepts.054/.070 [1.37/1.77] PC Board.180 [4.57] J.295 [7.49].155 [3.94] Post Length Technical Documents: (pages 186, 187): Product Specification Intercontact Keying Plugs Material: Natural color polyester Part No ( [2.54] Centerline) [2.54] Centerline No. of Dimensions Post Part Dual Positions B C** D E F G H J Length* Numbers , 2 **Metric equivalent for post lengths are = [3.18];.187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics. [3.18] Centerline Mid-High Mounting Ears.250 [6.35].141/.153 [3.58/3.88] Retention Feature No. of Dimensions Post Part Dual Positions B C** D E F G H J Length* Numbers Part No ( [3.18] Centerline) **Metric equivalent for post lengths are = [3.18];.187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics.

21 Standard Edge II Connectors (Continued) [2.54] and [3.18] Centerline, Vertical Wrap- Type Posts, Mid-High Mounting Ears.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp..150 [3.81] Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated with [ ] gold in contact area, tin on posts, with entire contact nickel underplated Related Product Data: Performance Specifications page 15 PC Board Hole Layout page 26 PC Board Edge Pattern page 27 Special pplication page [9.35].610 [15.49].250 [6.35] H G D C F.128 [3.25] Dia..180 [4.57].300 [7.62].550 [13.97].060 [1.52] ccepts.054/.070 [1.37/1.77] PC Board.295 [7.49].155 [3.94] Technical Documents: (pages 186, 187): Product Specification B E J Post Length Intercontact Keying Plugs Material: Natural color polyester [2.54] Centerline Part No ( [2.54] Centerline) No. of Dimensions Post Part Dual Positions B C** D E F G H J Length* Numbers **Metric equivalent for post length is.570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics [3.18] Centerline Part No ( [3.18] Centerline) No. of Dimensions Post Part Dual Positions B C** D E F G H J Length* Numbers **Metric equivalent for post length is.570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics

22 Standard Edge II Connectors (Continued) [2.54] and [3.18] Centerlines, Card Extender Contacts.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp..128 [3.25] Dia. Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated with [ ] gold in contact area, tin on posts, with entire contact nickel underplated.368 [9.35].180 [4.67] H G D C.150 [3.81].300 [7.62] Related Product Data: Performance Specifications page 15 PC Board Hole Layout page 26 PC Board Edge Pattern page 27 Technical Documents: (pages 186, 187): Product Specification Mounting Block Material: Natural color nylon.062 [1.57] Dia. Roll Pin Card Extender Connector Housing Ref. #5 Self Tapping Screws.610 [15.49] E F B.060 [1.52].180 [4.57].550 [13.97] ccepts.054/.070 [1.37/1.77] PC Board.250 [6.35] Fits.054/.070 [1.37/1.77] PC Board.340 [8.63].295 [7.49].155 [3.94] [2.54] Centerline Mounting Block.062 [1.57] PC Board Ref. Kit Part No Each kit includes 2 mounting blocks, 2 self tapping screws, #5 x.437 [11.10] and 2 roll pins,.075 x.250 [1.57 x 6.35] Intercontact Keying Plugs Material: Natural color polyester Part No ( [3.18] Centerline) No. of Dimensions Dual Positions B C** D E F G H *C dimension is card slot length. 1No mounting ears. Note: Other connector sizes can be made available, consult Tyco Electronics. [3.18] Centerline No. of Dimensions Dual Positions B C** D E F G H *C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. Part Numbers Part Numbers Part Number ( [2.54] Centerline)

23 Standard Edge II Card Edge Connectors [2.54] Right-ngle Solder Posts, with Low and No Mounting Ears.064 [1.63] Sq. x.130 [3.30] Dp. Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp. ccepts.054/.070 [1.37/1.77] PC Board Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, duplex plated as follows: Plating [ ] gold in contact area, tin on posts, with entire contact nickel underplated Plating B [ ] gold in contact area, tin on posts, with entire contact nickel underplated Related Product Data: Performance Specifications page 15 Technical Documents: Product Specification [9.35].610 [15.49].250 [6.25] [2.54].128 [3.25] Dia. [2.54] D C E F B.080 [1.82].300 [7.62].550 [13.97].295 [7.49] G With Board Locks ccepts.054/.070 [1.37/1.77] PC Board G Post Length Post Length.155 [3.94].295 [7.49].155 [3.94] Low Mounting Ears Intercontact Keying Plug Material: Natural color polyester Part Number ( [2.54] Centerline) Low Mounting Ears No. of Dimensions Post Part Numbers Dual Positions B C* D E F G1 Length2 (Plating ) No Mounting Ears xx xx xx *C dimension is card slot length. 1 Metric equivalent for x.150 and x.200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is.090 = [2.27]. 3 Connector with Board Locks. Note: Other connector sizes can be made available, consult Tyco Electronics No. of Dimensions Post Part Numbers Dual Positions B C* D G1 Length2 Plating Plating B x x x x x x *C dimension is card slot length. 1 Metric equivalent for x.150 and x.200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is.090 = [2.27]. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 23

24 Standard Edge II Card Edge Connectors [2.54] Centerline Vertical Solder Posts, Retention Feature, Without Mounting Ears Intercontact Key Slot.064 [1.63] Sq. x.130 [3.30] Dp. Material and Finish: Housing Black glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, duplex plated as follows: Plating [ ] gold in contact area, tin on posts, with entire contact nickel underplated Plating B [ ] gold in contact area, tin on posts, with entire contact nickel underplated Plating C Gold flash in contact area, tin on posts, with entire contact nickel underplated Technical Documents: Product Specification [1.63] Sq. x.130 [3.30] Dp. [2.54].610 [15.49] [2.54] Typ. D C B.060 [1.52].368 [9.35].550 [13.97] ccepts.054/.070 [1.37/1.77] PC Board.191 [4.85].155 [3.94].295 [7.49] Post Length Intercontact Keying Plug Material: Natural color polyester.141/.153 [3.58/3.88] Retention Feature Part Number ( [2.54] Centerline) No. of Dimensions Post Retention PartNumbers Dual Positions B C** D Length* Feature Plating , , or 31-34, , 49-52, , 55-58, 63-66, **Metric equivalent for post length is = [3.18]. **C dimension is card slot length. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 24

25 Standard Edge II Card Edge Connectors [2.54] Centerline, Special 18/31 Dual Combination Connector, Vertical Solder Posts, Without Mounting Ears [2.54].200 [5.08].368 [9.35] Material and Finish: Housing Black glass-filled polyester, 94V-0 rated, except where noted Contacts Phosphor bronze, plated with [ ] gold in contact area (except where noted), tin on posts, with entire contact nickel underplated Technical Documents: Product Specification Intercontact Keying Plug [2.54] [48.26].610 [15.49].400 [10.16] [138.68] [135.89] [81.28].550 [13.97].060 [1.52] Retention Feature ccepts.054/.070 [1.37/1.77] PC Board.191 [4.85] Solder Posts.141/.153 [3.58/3.88].295 [7.49] Material: Natural color polyester Part Number ( [2.54] Centerline) No. of Dual Positions 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts Post Dimension Retention Type Feature Part Numbers 3-6, 41, 42, , 52, None , 41, 42, 51, 52, , 6, 31, 32, , 42, 93, None Housing material is high temperature glass-filled polyester, gray. 2 Contact area is gold flash. Notes: 1. Card slot length is [134.62]. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 25

26 Standard Edge II Connectors (Continued) Recommended PC Board Hole Layouts Vertical Post Connectors D C ±.003 Dia. [±0.08] B.128 [3.25] Dia. F Connector Type Solder Post/Retention Solder Post/Retention Solder Post, Mounting Ears Solder Post, W/O Mounting Ears Wrap-Type Post Wrap-Type Post Dimensions B C D F /.200/ / / Notes: 1. Refer to page 24 for D Dimensions and Dual Positions. 2. No mounting ears. Dimensions do not apply. 3. Refer to page 20 for D and F Dimensions and Dual Positions. 4. Refer to pages 18 and 19 for D Dimensions and Dual Positions. 5. Refer to page 21 for D and F Dimensions and Dual Positions. See Note 1 See Note 2 See Note 4 See Note 2 See Note 3 See Note 3 See Note 4 See Note 2 See Note 5 See Note 5 See Note 5 See Note 5 Right-ngle Post Connectors F D B.128 [3.25] Dia. C ±.003 Dia. [±0.08].337 [8.56] G Connector Type Right-ngle Posts, Mounting Ears Right-ngle Posts, No Mounting Ears Notes: 1. Refer to page 23 for D and F Dimensions and Dual Positions. 2. Refer to page 23 for D Dimensions and Dual Positions. 3. No Mounting Ears, Dimensions do not apply. Dimensions B C D F G See Note 1 See Note or or See Note 2 See Note 3 See Note 3 26

27 Standard Edge II Connectors (Continued) Recommended PC Board Edge Pattern PC Board Edge Pattern for [2.54] and [3.18] Centerline Datum C L.050 [1.27] Intercontact Key Slot.015 [0.38] x 45 Chamfer.295 [7.49] Min. Engagement Depth.310 [7.87] Min. B D ±.005 [±0.13].054/.070 [1.37/1.77] C ±.005 [±0.13] [2.54] Centerline [3.18] Centerline No. of =.093 [2.36] =.118 [3.00] Dual B =.050 [1.27] B =.075 [1.90] Positions C D C D

28 Cantilever Series Card Edge Connectors Product Facts Double readout Card Edge connectors use dip solder contacts Large lead-in chamfers allow easy PC board installation Insulator standoffs prevent solder from wicking Various lengths for custom applications Contact option, single or dual row Description The Cantilever Beam Series products from Tyco Electronics are double readout cardedge connectors, using dip solder contacts. Tooled for flexible manufacturing, these Card Edge connectors are readily available in a broad assortment of sizes and mounting styles. Our connectors meet industry standards. Design dvantages Circuit Integrity: Robust cantilever contacts are designed to promote optimal normal forces at the lowest possible cost. Our uniquely contoured contact mating surface gives you constant engagement, even when subjected to continuous vibration. Ease of ssembly: Generous lead-in chamfers let your P.C. board slide easily into the connector. Insulator standoffs are provided to facilitate cleaning and prevent solder from wicking. vailability, flexibility, performance and very low cost make the Cantilever Series from Tyco Electronics the clear choice in Card Edge connectors. Cantilever Beam The Cantilever Beam Card Edge connector comes with standard high temperature plastic insulators. Contacts are available in a variety of lengths to accommodate various custom applications. Standoffs allow for cleaning and draining and are available as an option on most insulator bodies. Cantilever Beam Card Edge offers a variety of card slot depths. full scoop option is available for ease of installation in applications where visibility is limited. Contact options vary in this series from dual row standard contacts, single row options and press-fit. 28

29 Cantilever Series Connectors x.200 [2.54 x 5.08] Centerline Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR ±.010 Contact Gap [.51±.25] Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method [9.40] [2.54] [48.26] [2.54] Ref [43.18].400 [10.16].145 [3.68].13 [3.30].040±.003 [1.02±.080] Dia [138.68] [134.62].200 [5.08] Ref. 5 [129.54] [76.20] [81.28].200 [5.08].300 Card Slot Depth [7.62].200 [5.08].300 [7.62].610 [15.49].06 [1.52].06 [1.52] [2.54] Typ. Ordering Information cquired Part Number C8D52DS29C1M191 Insulator with molded-in polarizing key with card guide chamber. The card slot lengths are [48.26] and [81.28]. Includes retention tails for.062 [1.57] PCB to hold connectors securely during handling. C8D52DS29C1M195 Same as above. No retention tails. 29

30 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Cantilever Series Connectors x.200 [2.54 x 5.08] Centerline Dip Solder Tails,.300 [7.62] Card Slot Depth D Physical Properties: E.020±.010 Contact Gap [.51±.25] Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: [2.54] Typ. B C.250 [6.35].370 [9.40].610 [15.49].145 [3.68] J.300 Card Slot Depth [7.62].200 [5.08] Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: E [1.52] [4.57].020 Typ. Dia. [0.51] Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method [3.25] Dia..040±.003 [1.02±.08] Dia. Dim E Dim B Related Product Data: Daughter Card Edge Pattern page 57 [2.54].200 [5.08] Mounting Styles [3.18] Dia. #4-40 [3.18] Dia..250 [6.35].250 [6.35] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 30

31 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row Mounting Ear Options No. of D u a l D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h R e a d o u t Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear B C D E P o s i t i o n s " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.130" [3.30] (DIM J ) C 8 D 06 D S 29 1 C 8 D 06 D S 29 B 1 C 8 D 06 D S 29 C 1 C 8 D 06 D S 29 D 1 C 8 D 06 D S 29 E C 8 D 10 D S 29 1 C 8 D 10 D S 29 B 1 C 8 D 10 D S 29 C 1 C 8 D 10 D S 29 D 1 C 8 D 10 D S 29 E C 8 D 12 D S 29 1 C 8 D 12 D S 29 B 1 C 8 D 12 D S 29 C 1 C 8 D 12 D S 29 D 1 C 8 D 12 D S 29 E C 8 D 15 D S 29 1 C 8 D 15 D S 29 B 1 C 8 D 15 D S 29 C 1 C 8 D 15 D S 29 D 1 C 8 D 15 D S 29 E C 8 D 18 D S 29 1 C 8 D 18 D S 29 B 1 C 8 D 18 D S 29 C 1 C 8 D 18 D S 29 D 1 C 8 D 18 D S 29 E C 8 D 20 D S 29 1 C 8 D 20 D S 29 B 1 C 8 D 20 D S 29 C 1 C 8 D 20 D S 29 D 1 C 8 D 20 D S 29 E C 8 D 22 D S 29 1 C 8 D 22 D S 29 B 1 C 8 D 22 D S 29 C 1 C 8 D 22 D S 29 D 1 C 8 D 22 D S 29 E C 8 D 25 D S 29 1 C 8 D 25 D S 29 B 1 C 8 D 25 D S 29 C 1 C 8 D 25 D S 29 D 1 C 8 D 25 D S 29 E C 8 D 28 D S 29 1 C 8 D 28 D S 29 B 1 C 8 D 28 D S 29 C 1 C 8 D 28 D S 29 D 1 C 8 D 28 D S 29 E C 8 D 30 D S 29 1 C 8 D 30 D S 29 B 1 C 8 D 30 D S 29 C 1 C 8 D 30 D S 29 D 1 C 8 D 30 D S 29 E C 8 D 31 D S 29 1 C 8 D 31 D S 29 B 1 C 8 D 31 D S 29 C 1 C 8 D 31 D S 29 D 1 C 8 D 31 D S 29 E C 8 D 35 D S 29 1 C 8 D 35 D S 29 B 1 C 8 D 35 D S 29 C 1 C 8 D 35 D S 29 D 1 C 8 D 35 D S 29 E C 8 D 36 D S 29 1 C 8 D 36 D S 29 B 1 C 8 D 36 D S 29 C 1 C 8 D 36 D S 29 D 1 C 8 D 36 D S 29 E C 8 D 40 D S 29 1 C 8 D 40 D S 29 B 1 C 8 D 40 D S 29 C 1 C 8 D 40 D S 29 D 1 C 8 D 40 D S 29 E C 8 D 43 D S 29 1 C 8 D 43 D S 29 B 1 C 8 D 43 D S 29 C 1 C 8 D 43 D S 29 D 1 C 8 D 43 D S 29 E C 8 D 50 D S 29 1 C 8 D 50 D S 29 B 1 C 8 D 50 D S 29 C 1 C 8 D 50 D S 29 D 1 C 8 D 50 D S 29 E C 8 D 60 D S 29 1 C 8 D 60 D S 29 B 1 C 8 D 60 D S 29 C 1 C 8 D 60 D S 29 D 1 C 8 D 60 D S 29 E 1 Tail Length.160" [4.06] (DIM J ) C 8 D 06 D S 29 2 C 8 D 06 D S 29 B 2 C 8 D 06 D S 29 C 2 C 8 D 06 D S 29 D 2 C 8 D 06 D S 29 E C 8 D 10 D S 29 2 C 8 D 10 D S 29 B 2 C 8 D 10 D S 29 C 2 C 8 D 10 D S 29 D 2 C 8 D 10 D S 29 E C 8 D 12 D S 29 2 C 8 D 12 D S 29 B 2 C 8 D 12 D S 29 C 2 C 8 D 12 D S 29 D 2 C 8 D 12 D S 29 E C 8 D 15 D S 29 2 C 8 D 15 D S 29 B 2 C 8 D 15 D S 29 C 2 C 8 D 15 D S 29 D 2 C 8 D 15 D S 29 E C 8 D 18 D S 29 2 C 8 D 18 D S 29 B 2 C 8 D 18 D S 29 C 2 C 8 D 18 D S 29 D 2 C 8 D 18 D S 29 E C 8 D 20 D S 29 2 C 8 D 20 D S 29 B 2 C 8 D 20 D S 29 C 2 C 8 D 20 D S 29 D 2 C 8 D 20 D S 29 E C 8 D 22 D S 29 2 C 8 D 22 D S 29 B 2 C 8 D 22 D S 29 C 2 C 8 D 22 D S 29 D 2 C 8 D 22 D S 29 E C 8 D 25 D S 29 2 C 8 D 25 D S 29 B 2 C 8 D 25 D S 29 C 2 C 8 D 25 D S 29 D 2 C 8 D 25 D S 29 E C 8 D 28 D S 29 2 C 8 D 28 D S 29 B 2 C 8 D 28 D S 29 C 2 C 8 D 28 D S 29 D 2 C 8 D 28 D S 29 E C 8 D 30 D S 29 2 C 8 D 30 D S 29 B 2 C 8 D 30 D S 29 C 2 C 8 D 30 D S 29 D 2 C 8 D 30 D S 29 E C 8 D 31 D S 29 2 C 8 D 31 D S 29 B 2 C 8 D 31 D S 29 C 2 C 8 D 31 D S 29 D 2 C 8 D 31 D S 29 E C 8 D 35 D S 29 2 C 8 D 35 D S 29 B 2 C 8 D 35 D S 29 C 2 C 8 D 35 D S 29 D 2 C 8 D 35 D S 29 E C 8 D 36 D S 29 2 C 8 D 36 D S 29 B 2 C 8 D 36 D S 29 C 2 C 8 D 36 D S 29 D 2 C 8 D 36 D S 29 E C 8 D 40 D S 29 2 C 8 D 40 D S 29 B 2 C 8 D 40 D S 29 C 2 C 8 D 40 D S 29 D 2 C 8 D 40 D S 29 E C 8 D 43 D S 29 2 C 8 D 43 D S 29 B 2 C 8 D 43 D S 29 C 2 C 8 D 43 D S 29 D 2 C 8 D 43 D S 29 E 2 31

32 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row Mounting Ear Options No. of D u a l D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h R e a d o u t Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear P o s i t i o n s B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.160" [4.06] (DIM J ) (Continued) C 8 D 50 D S 29 2 C 8 D 50 D S 29 B 2 C 8 D 50 D S 29 C 2 C 8 D 50 D S 29 D 2 C 8 D 50 D S 29 E C 8 D 60 D S 29 2 C 8 D 60 D S 29 B 2 C 8 D 60 D S 29 C 2 C 8 D 60 D S 29 D 2 C 8 D 60 D S 29 E 2 Tail Length.220" [5.59] (DIM J ) C 8 D 06 D S 29 3 C 8 D 06 D S 29 B 3 C 8 D 06 D S 29 C 3 C 8 D 06 D S 29 D 3 C 8 D 06 D S 29 E C 8 D 10 D S 29 3 C 8 D 10 D S 29 B 3 C 8 D 10 D S 29 C 3 C 8 D 10 D S 29 D 3 C 8 D 10 D S 29 E C 8 D 12 D S 29 3 C 8 D 12 D S 29 B 3 C 8 D 12 D S 29 C 3 C 8 D 12 D S 29 D 3 C 8 D 12 D S 29 E C 8 D 15 D S 29 3 C 8 D 15 D S 29 B 3 C 8 D 15 D S 29 C 3 C 8 D 15 D S 29 D 3 C 8 D 15 D S 29 E C 8 D 18 D S 29 3 C 8 D 18 D S 29 B 3 C 8 D 18 D S 29 C 3 C 8 D 18 D S 29 D 3 C 8 D 18 D S 29 E C 8 D 20 D S 29 3 C 8 D 20 D S 29 B 3 C 8 D 20 D S 29 C 3 C 8 D 20 D S 29 D 3 C 8 D 20 D S 29 E C 8 D 22 D S 29 3 C 8 D 22 D S 29 B 3 C 8 D 22 D S 29 C 3 C 8 D 22 D S 29 D 3 C 8 D 22 D S 29 E C 8 D 25 D S 29 3 C 8 D 25 D S 29 B 3 C 8 D 25 D S 29 C 3 C 8 D 25 D S 29 D 3 C 8 D 25 D S 29 E C 8 D 28 D S 29 3 C 8 D 28 D S 29 B 3 C 8 D 28 D S 29 C 3 C 8 D 28 D S 29 D 3 C 8 D 28 D S 29 E C 8 D 30 D S 29 3 C 8 D 30 D S 29 B 3 C 8 D 30 D S 29 C 3 C 8 D 30 D S 29 D 3 C 8 D 30 D S 29 E C 8 D 31 D S 29 3 C 8 D 31 D S 29 B 3 C 8 D 31 D S 29 C 3 C 8 D 31 D S 29 D 3 C 8 D 31 D S 29 E C 8 D 35 D S 29 3 C 8 D 35 D S 29 B 3 C 8 D 35 D S 29 C 3 C 8 D 35 D S 29 D 3 C 8 D 35 D S 29 E C 8 D 36 D S 29 3 C 8 D 36 D S 29 B 3 C 8 D 36 D S 29 C 3 C 8 D 36 D S 29 D 3 C 8 D 36 D S 29 E C 8 D 40 D S 29 3 C 8 D 40 D S 29 B 3 C 8 D 40 D S 29 C 3 C 8 D 40 D S 29 D 3 C 8 D 40 D S 29 E C 8 D 43 D S 29 3 C 8 D 43 D S 29 B 3 C 8 D 43 D S 29 C 3 C 8 D 43 D S 29 D 3 C 8 D 43 D S 29 E C 8 D 50 D S 29 3 C 8 D 50 D S 29 B 3 C 8 D 50 D S 29 C 3 C 8 D 50 D S 29 D 3 C 8 D 50 D S 29 E C 8 D 60 D S 29 3 C 8 D 60 D S 29 B 3 C 8 D 60 D S 29 C 3 C 8 D 60 D S 29 D 3 C 8 D 60 D S 29 E 3 32

33 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Cantilever Series Connectors 100 x.200 [2.54 x 5.08],.510 [12.95] and.395 [10.03] Card Slot Depth, Full Scoop.054 to.071 ccepts [3.37 to 1.80] Thk. PC Board Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum.390 [9.91] [2.54] B C.180 [4.57].02 [.51] Contact Gap Electrical Properties: Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms.705 [17.91] Card Slot Depth Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 C.180 [4.57] Vibration MIL-STD-202 method 204 Related Product Data Daughter Card Edge Pattern page ±.003 [1.02±.08] Dia. Dim C.200 [5.08] [2.54] 33

34 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row Full Scoop No. of Dual D i m e n s i o n s cquired Part Readout Pos. B C N u m b e r.510" [12.95] Card Slot Depth " [10.03] Card Slot Depth W 8 D 1 8 D S W 8 D 2 0 D S W 8 D 2 2 D S W 8 D 2 5 D S W 8 D 2 8 D S W 8 D 3 0 D S W 8 D 3 5 D S W 8 D 3 6 D S W 8 D 4 0 D S W 8 D 4 3 D S W 8 D 4 5 D S W 8 D 5 0 D S W 8 D 6 0 D S W 8 D 1 8 D S W 8 D 2 0 D S W 8 D 2 2 D S W 8 D 2 5 D S W 8 D 2 8 D S W 8 D 3 0 D S W 8 D 3 5 D S W 8 D 3 6 D S W 8 D 4 0 D S W 8 D 4 3 D S W 8 D 4 5 D S W 8 D 5 0 D S W 8 D 6 0 D S

35 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: Operation Voltage 1000 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling.128 MIL-STD-202 method 107 [3.25] Dia. Vibration MIL-STD-202 method 204 Related Product Data: Daughter Card Edge Pattern page 57 Cantilever Series Connectors x.250 [3.18 x 6.35] Centerline, Dip Solder Tails,.300 [7.62] Card Slot Depth [3.18] [2.54] Typ..040±.003 [1.02±.08] Dia. D E B E C Dim E Dim B.250 [6.35].370 [9.40].250 [6.35] [1.52] [4.57].145 [3.68].020 Typ. Dia. [0.51] J.610 [15.49].020±.010 Contact Gap [.51±.25].300 Card Slot Depth [7.62].250 [6.35] Mounting Styles [3.18] Dia. #4-40 [3.18] Dia..250 [6.35].250 [6.35] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 35

36 Ordering Information " [3.18] Centerline /.250" [6.35] Row-to-Row Mounting Ear Options No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear R e a d o u t B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.130 [3.30] (DIM. J ) C 7 D 06 D S 29 1 C 7 D 06 D S 29 B 1 C 7 D 06 D S 29 C 1 C 7 D 06 D S 29 D 1 C 7 D 06 D S 29 E C 7 D 10 D S 29 1 C 7 D 10 D S 29 B 1 C 7 D 10 D S 29 C 1 C 7 D 10 D S 29 D 1 C 7 D 10 D S 29 E C 7 D 15 D S 29 1 C 7 D 15 D S 29 B 1 C 7 D 15 D S 29 C 1 C 7 D 15 D S 29 D 1 C 7 D 15 D S 29 E C 7 D 18 D S 29 1 C 7 D 18 D S 29 B 1 C 7 D 18 D S 29 C 1 C 7 D 18 D S 29 D 1 C 7 D 18 D S 29 E C 7 D 22 D S 29 1 C 7 D 22 D S 29 B 1 C 7 D 22 D S 29 C 1 C 7 D 22 D S 29 D 1 C 7 D 22 D S 29 E C 7 D 25 D S 29 1 C 7 D 25 D S 29 B 1 C 7 D 25 D S 29 C 1 C 7 D 25 D S 29 D 1 C 7 D 25 D S 29 E C 7 D 28 D S 29 1 C 7 D 28 D S 29 B 1 C 7 D 28 D S 29 C 1 C 7 D 28 D S 29 D 1 C 7 D 28 D S 29 E C 7 D 30 D S 29 1 C 7 D 30 D S 29 B 1 C 7 D 30 D S 29 C 1 C 7 D 30 D S 29 D 1 C 7 D 30 D S 29 E C 7 D 31 D S 29 1 C 7 D 31 D S 29 B 1 C 7 D 31 D S 29 C 1 C 7 D 31 D S 29 D 1 C 7 D 31 D S 29 E C 7 D 35 D S 29 1 C 7 D 35 D S 29 B 1 C 7 D 35 D S 29 C 1 C 7 D 35 D S 29 D 1 C 7 D 35 D S 29 E C 7 D 36 D S 29 1 C 7 D 36 D S 29 B 1 C 7 D 36 D S 29 C 1 C 7 D 36 D S 29 D 1 C 7 D 36 D S 29 E C 7 D 40 D S 29 1 C 7 D 40 D S 29 B 1 C 7 D 40 D S 29 C 1 C 7 D 40 D S 29 D 1 C 7 D 40 D S 29 E C 7 D 43 D S 29 1 C 7 D 43 D S 29 B 1 C 7 D 43 D S 29 C 1 C 7 D 43 D S 29 D 1 C 7 D 43 D S 29 E C 7 D 50 D S 29 1 C 7 D 50 D S 29 B 1 C 7 D 50 D S 29 C 1 C 7 D 50 D S 29 D 1 C 7 D 50 D S 29 E 1 Tail Length.160 [4.06] (DIM. J ) C 7 D 06 D S 29 3 C 7 D 06 D S 29 B 3 C 7 D 06 D S 29 C 3 C 7 D 06 D S 29 D 3 C 7 D 06 D S 29 E C 7 D 10 D S 29 3 C 7 D 10 D S 29 B 3 C 7 D 10 D S 29 C 3 C 7 D 10 D S 29 D 3 C 7 D 10 D S 29 E C 7 D 15 D S 29 3 C 7 D 15 D S 29 B 3 C 7 D 15 D S 29 C 3 C 7 D 15 D S 29 D 3 C 7 D 15 D S 29 E C 7 D 18 D S 29 3 C 7 D 18 D S 29 B 3 C 7 D 18 D S 29 C 3 C 7 D 18 D S 29 D 3 C 7 D 18 D S 29 E C 7 D 22 D S 29 3 C 7 D 22 D S 29 B 3 C 7 D 22 D S 29 C 3 C 7 D 22 D S 29 D 3 C 7 D 22 D S 29 E C 7 D 25 D S 29 3 C 7 D 25 D S 29 B 3 C 7 D 25 D S 29 C 3 C 7 D 25 D S 29 D 3 C 7 D 25 D S 29 E C 7 D 28 D S 29 3 C 7 D 28 D S 29 B 3 C 7 D 28 D S 29 C 3 C 7 D 28 D S 29 D 3 C 7 D 28 D S 29 E C 7 D 30 D S 29 3 C 7 D 30 D S 29 B 3 C 7 D 30 D S 29 C 3 C 7 D 30 D S 29 D 3 C 7 D 30 D S 29 E C 7 D 31 D S 29 3 C 7 D 31 D S 29 B 3 C 7 D 31 D S 29 C 3 C 7 D 31 D S 29 D 3 C 7 D 31 D S 29 E C 7 D 35 D S 29 3 C 7 D 35 D S 29 B 3 C 7 D 35 D S 29 C 3 C 7 D 35 D S 29 D 3 C 7 D 35 D S 29 E C 7 D 36 D S 29 3 C 7 D 36 D S 29 B 3 C 7 D 36 D S 29 C 3 C 7 D 36 D S 29 D 3 C 7 D 36 D S 29 E C 7 D 40 D S 29 3 C 7 D 40 D S 29 B 3 C 7 D 40 D S 29 C 3 C 7 D 40 D S 29 D 3 C 7 D 40 D S 29 E C 7 D 43 D S 29 3 C 7 D 43 D S 29 B 3 C 7 D 43 D S 29 C 3 C 7 D 43 D S 29 D 3 C 7 D 43 D S 29 E C 7 D 50 D S 29 3 C 7 D 50 D S 29 B 3 C 7 D 50 D S 29 C 3 C 7 D 50 D S 29 D 3 C 7 D 50 D S 29 E 3 36

37 Ordering Information " [3.18] Centerline /.250" [6.35] Row-to-Row Mounting Ear Options No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear R e a d o u t B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.220 [5.59] (DIM. J ) C 7 D 06 D S 29 4 C 7 D 06 D S 29 B 4 C 7 D 06 D S 29 C 4 C 7 D 06 D S 29 D 4 C 7 D 06 D S 29 E C 7 D 10 D S 29 4 C 7 D 10 D S 29 B 4 C 7 D 10 D S 29 C 4 C 7 D 10 D S 29 D 4 C 7 D 10 D S 29 E C 7 D 15 D S 29 4 C 7 D 15 D S 29 B 4 C 7 D 15 D S 29 C 4 C 7 D 15 D S 29 D 4 C 7 D 15 D S 29 E C 7 D 18 D S 29 4 C 7 D 18 D S 29 B 4 C 7 D 18 D S 29 C 4 C 7 D 18 D S 29 D 4 C 7 D 18 D S 29 E C 7 D 22 D S 29 4 C 7 D 22 D S 29 B 4 C 7 D 22 D S 29 C 4 C 7 D 22 D S 29 D 4 C 7 D 22 D S 29 E C 7 D 25 D S 29 4 C 7 D 25 D S 29 B 4 C 7 D 25 D S 29 C 4 C 7 D 25 D S 29 D 4 C 7 D 25 D S 29 E C 7 D 28 D S 29 4 C 7 D 28 D S 29 B 4 C 7 D 28 D S 29 C 4 C 7 D 28 D S 29 D 4 C 7 D 28 D S 29 E C 7 D 30 D S 29 4 C 7 D 30 D S 29 B 4 C 7 D 30 D S 29 C 4 C 7 D 30 D S 29 D 4 C 7 D 30 D S 29 E C 7 D 31 D S 29 4 C 7 D 31 D S 29 B 4 C 7 D 31 D S 29 C 4 C 7 D 31 D S 29 D 4 C 7 D 31 D S 29 E C 7 D 35 D S 29 4 C 7 D 35 D S 29 B 4 C 7 D 35 D S 29 C 4 C 7 D 35 D S 29 D 4 C 7 D 35 D S 29 E C 7 D 36 D S 29 4 C 7 D 36 D S 29 B 4 C 7 D 36 D S 29 C 4 C 7 D 36 D S 29 D 4 C 7 D 36 D S 29 E C 7 D 40 D S 29 4 C 7 D 40 D S 29 B 4 C 7 D 40 D S 29 C 4 C 7 D 40 D S 29 D 4 C 7 D 40 D S 29 E C 7 D 43 D S 29 4 C 7 D 43 D S 29 B 4 C 7 D 43 D S 29 C 4 C 7 D 43 D S 29 D 4 C 7 D 43 D S 29 E C 7 D 50 D S 29 4 C 7 D 50 D S 29 B 4 C 7 D 50 D S 29 C 4 C 7 D 50 D S 29 D 4 C 7 D 50 D S 29 E 4 37

38 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Cantilever Series.156 x.200 [3.96 x 5.08] Centerline, Dip Solder Tails,.300 [7.62] Card Slot Depth D.145 [3.68] J.020±.010 Contact Gap [.51±.25].300 Card Slot Depth [7.62] Physical Properties: E.200 [5.08] Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties:.156 [3.96] Typ. B C.250 [6.35].370 [9.40].610 [15.49] Operation Voltage 1500 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: E [1.52] [4.57].020 Typ. Dia. [0.51] Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method [3.25] Dia..040±.003 [1.02±.08] Dia. Dim E Dim B Related Product Data: Daughter Card Edge Pattern page [3.96].200 [5.08] Mounting Styles [3.18] Dia. #4-40 [3.18] Dia..250 [6.35].250 [6.35] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 38

39 Ordering Information.156" [3.96] Centerline /.200" [5.08] Row-to-Row Mounting Ear Options No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear R e a d o u t B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.130 [3.30] (DIM. J ) C 6 D 06 D S 29 1 C 6 D 06 D S 29 B 1 C 6 D 06 D S 29 C 1 C 6 D 06 D S 29 D 1 C 6 D 06 D S 29 E C 6 D 10 D S 29 1 C 6 D 10 D S 29 B 1 C 6 D 10 D S 29 C 1 C 6 D 10 D S 29 D 1 C 6 D 10 D S 29 E C 6 D 12 D S 29 1 C 6 D 12 D S 29 B 1 C 6 D 12 D S 29 C 1 C 6 D 12 D S 29 D 1 C 6 D 12 D S 29 E C 6 D 15 D S 29 1 C 6 D 15 D S 29 B 1 C 6 D 15 D S 29 C 1 C 6 D 15 D S 29 D 1 C 6 D 15 D S 29 E C 6 D 18 D S 29 1 C 6 D 18 D S 29 B 1 C 6 D 18 D S 29 C 1 C 6 D 18 D S 29 D 1 C 6 D 18 D S 29 E C 6 D 20 D S 29 1 C 6 D 20 D S 29 B 1 C 6 D 20 D S 29 C 1 C 6 D 20 D S 29 D 1 C 6 D 20 D S 29 E C 6 D 22 D S 29 1 C 6 D 22 D S 29 B 1 C 6 D 22 D S 29 C 1 C 6 D 22 D S 29 D 1 C 6 D 22 D S 29 E C 6 D 25 D S 29 1 C 6 D 25 D S 29 B 1 C 6 D 25 D S 29 C 1 C 6 D 25 D S 29 D 1 C 6 D 25 D S 29 E C 6 D 28 D S 29 1 C 6 D 28 D S 29 B 1 C 6 D 28 D S 29 C 1 C 6 D 28 D S 29 D 1 C 6 D 28 D S 29 E C 6 D 30 D S 29 1 C 6 D 30 D S 29 B 1 C 6 D 30 D S 29 C 1 C 6 D 30 D S 29 D 1 C 6 D 30 D S 29 E C 6 D 31 D S 29 1 C 6 D 31 D S 29 B 1 C 6 D 31 D S 29 C 1 C 6 D 31 D S 29 D 1 C 6 D 31 D S 29 E C 6 D 35 D S 29 1 C 6 D 35 D S 29 B 1 C 6 D 35 D S 29 C 1 C 6 D 35 D S 29 D 1 C 6 D 35 D S 29 E C 6 D 36 D S 29 1 C 6 D 36 D S 29 B 1 C 6 D 36 D S 29 C 1 C 6 D 36 D S 29 D 1 C 6 D 36 D S 29 E C 6 D 40 D S 29 1 C 6 D 40 D S 29 B 1 C 6 D 40 D S 29 C 1 C 6 D 40 D S 29 D 1 C 6 D 40 D S 29 E C 6 D 43 D S 29 1 C 6 D 43 D S 29 B 1 C 6 D 43 D S 29 C 1 C 6 D 43 D S 29 D 1 C 6 D 43 D S 29 E C 6 D 50 D S 29 1 C 6 D 50 D S 29 B 1 C 6 D 50 D S 29 C 1 C 6 D 50 D S 29 D 1 C 6 D 50 D S 29 E 1 Tail Length.160 [4.06] (DIM. J ) C 6 D 06 D S 29 3 C 6 D 06 D S 29 B 3 C 6 D 06 D S 29 C 3 C 6 D 06 D S 29 D 3 C 6 D 06 D S 29 E C 6 D 10 D S 29 3 C 6 D 10 D S 29 B 3 C 6 D 10 D S 29 C 3 C 6 D 10 D S 29 D 3 C 6 D 10 D S 29 E C 6 D 12 D S 29 3 C 6 D 12 D S 29 B 3 C 6 D 12 D S 29 C 3 C 6 D 12 D S 29 D 3 C 6 D 12 D S 29 E C 6 D 15 D S 29 3 C 6 D 15 D S 29 B 3 C 6 D 15 D S 29 C 3 C 6 D 15 D S 29 D 3 C 6 D 15 D S 29 E C 6 D 18 D S 29 3 C 6 D 18 D S 29 B 3 C 6 D 18 D S 29 C 3 C 6 D 18 D S 29 D 3 C 6 D 18 D S 29 E C 6 D 20 D S 29 3 C 6 D 20 D S 29 B 3 C 6 D 20 D S 29 C 3 C 6 D 20 D S 29 D 3 C 6 D 20 D S 29 E C 6 D 22 D S 29 3 C 6 D 22 D S 29 B 3 C 6 D 22 D S 29 C 3 C 6 D 22 D S 29 D 3 C 6 D 22 D S 29 E C 6 D 25 D S 29 3 C 6 D 25 D S 29 B 3 C 6 D 25 D S 29 C 3 C 6 D 25 D S 29 D 3 C 6 D 25 D S 29 E C 6 D 28 D S 29 3 C 6 D 28 D S 29 B 3 C 6 D 28 D S 29 C 3 C 6 D 28 D S 29 D 3 C 6 D 28 D S 29 E C 6 D 30 D S 29 3 C 6 D 30 D S 29 B 3 C 6 D 30 D S 29 C 3 C 6 D 30 D S 29 D 3 C 6 D 30 D S 29 E C 6 D 31 D S 29 3 C 6 D 31 D S 29 B 3 C 6 D 31 D S 29 C 3 C 6 D 31 D S 29 D 3 C 6 D 31 D S 29 E C 6 D 35 D S 29 3 C 6 D 35 D S 29 B 3 C 6 D 35 D S 29 C 3 C 6 D 35 D S 29 D 3 C 6 D 35 D S 29 E C 6 D 36 D S 29 3 C 6 D 36 D S 29 B 3 C 6 D 36 D S 29 C 3 C 6 D 36 D S 29 D 3 C 6 D 36 D S 29 E C 6 D 40 D S 29 3 C 6 D 40 D S 29 B 3 C 6 D 40 D S 29 C 3 C 6 D 40 D S 29 D 3 C 6 D 40 D S 29 E C 6 D 43 D S 29 3 C 6 D 43 D S 29 B 3 C 6 D 43 D S 29 C 3 C 6 D 43 D S 29 D 3 C 6 D 43 D S 29 E C 6 D 50 D S 29 3 C 6 D 50 D S 29 B 3 C 6 D 50 D S 29 C 3 C 6 D 50 D S 29 D 3 C 6 D 50 D S 29 E 3 39

40 Ordering Information.156" [3.96] Centerline /.200" [5.08] Row-to-Row Mounting Ear Options No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear R e a d o u t B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded P o s i t i o n s T h r uh o l e i n s e r t Thru Hole i n s e r t Tail Length.220" [5.59] (DIM. J ) C 6 D 06 D S 29 4 C 6 D 06 D S 29 B 4 C 6 D 06 D S 29 C 4 C 6 D 06 D S 29 D 4 C 6 D 06 D S 29 E C 6 D 10 D S 29 4 C 6 D 10 D S 29 B 4 C 6 D 10 D S 29 C 4 C 6 D 10 D S 29 D 4 C 6 D 10 D S 29 E C 6 D 12 D S 29 4 C 6 D 12 D S 29 B 4 C 6 D 12 D S 29 C 4 C 6 D 12 D S 29 D 4 C 6 D 12 D S 29 E C 6 D 15 D S 29 4 C 6 D 15 D S 29 B 4 C 6 D 15 D S 29 C 4 C 6 D 15 D S 29 D 4 C 6 D 15 D S 29 E C 6 D 18 D S 29 4 C 6 D 18 D S 29 B 4 C 6 D 18 D S 29 C 4 C 6 D 18 D S 29 D 4 C 6 D 18 D S 29 E C 6 D 20 D S 29 4 C 6 D 20 D S 29 B 4 C 6 D 20 D S 29 C 4 C 6 D 20 D S 29 D 4 C 6 D 20 D S 29 E C 6 D 22 D S 29 4 C 6 D 22 D S 29 B 4 C 6 D 22 D S 29 C 4 C 6 D 22 D S 29 D 4 C 6 D 22 D S 29 E C 6 D 25 D S 29 4 C 6 D 25 D S 29 B 4 C 6 D 25 D S 29 C 4 C 6 D 25 D S 29 D 4 C 6 D 25 D S 29 E C 6 D 28 D S 29 4 C 6 D 28 D S 29 B 4 C 6 D 28 D S 29 C 4 C 6 D 28 D S 29 D 4 C 6 D 28 D S 29 E C 6 D 30 D S 29 4 C 6 D 30 D S 29 B 4 C 6 D 30 D S 29 C 4 C 6 D 30 D S 29 D 4 C 6 D 30 D S 29 E C 6 D 31 D S 29 4 C 6 D 31 D S 29 B 4 C 6 D 31 D S 29 C 4 C 6 D 31 D S 29 D 4 C 6 D 31 D S 29 E C 6 D 35 D S 29 4 C 6 D 35 D S 29 B 4 C 6 D 35 D S 29 C 4 C 6 D 35 D S 29 D 4 C 6 D 35 D S 29 E C 6 D 36 D S 29 4 C 6 D 36 D S 29 B 4 C 6 D 36 D S 29 C 4 C 6 D 36 D S 29 D 4 C 6 D 36 D S 29 E C 6 D 40 D S 29 4 C 6 D 40 D S 29 B 4 C 6 D 40 D S 29 C 4 C 6 D 40 D S 29 D 4 C 6 D 40 D S 29 E C 6 D 43 D S 29 4 C 6 D 43 D S 29 B 4 C 6 D 43 D S 29 C 4 C 6 D 43 D S 29 D 4 C 6 D 43 D S 29 E C 6 D 50 D S 29 4 C 6 D 50 D S 29 B 4 C 6 D 50 D S 29 C 4 C 6 D 50 D S 29 D 4 C 6 D 50 D S 29 E 4 40

41 Modified Bellows Card Edge Connectors Product Facts Sizes from 6 to 65 dual positions. Contact mating surface optimizes reliability by concentrating the normal force in the actual contact area. Mounting ear options accommodate both Panel and PC Board attachment. Solder stand-offs facilitate cleaning. Bifurcated contact design provides redundant points of contact to maximize reliability. Tail lengths available to accommodate.062" [1.57] through " [3.18] thick PCB Boards and Wire Wrap termination. Straight or Right ngle contact configurations. Description/pplication The modified bellows card edge connectors are dual readout and are designed for reliable termination to double sided PCB boards. Modified Bellows The modified bellows card edge connector offers a variety of tail lengths for solder and wire wrap applications. Contacts are available in straight tail or right angle configurations to meet your individual purpose. The modified bellows line of connectors offers a variety of card slot depths and has optional high temperature plastic insulators. Bifurcated contact design provides maximum reliability 41

42 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method 204 Related Product Data: Polarization Key page 57 Daughter Card Edge Pattern page 57 Modified Bellows Connectors x.200 [2.54 x 5.08], Straight Dip Solder nd Wire Wrap Tails.368 [9.53].128 [3.25] Dia. [2.54] C [2.54] Ref. B Dim E D Dim B.610 [15.49] SECTION X-X ROTTED 90º SECTION X-X E.025 [.64] Sq.200 [5.08] P=.040 [1.02] Dip Solder pplications P=.042 [1.07] For Wire Wrap pplications.200 [5.08] [ ] P.C. Board.300 [7.62] Card Depth J.250 [6.35] Mounting Styles.610 [15.49] Ref [4.57] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert

43 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row D i m e n s i o n s No. of D u a l R e a d o u t P o s i t i o n s B C D E Tail Length.160" [4.06] (DIM J ) Tail Length.220" [5.59] (DIM J ) Mounting Ear Options C e n t e r e d C e n t e r e d N o Flush F l u s h Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t 8 D 10 D S D 10 D S 29 B 2 8 D 10 D S 29 C 2 8 D 10 D S 29 D 2 8 D 10 D S 29 E 2 8 D 12 D S D 12 D S 29 B 2 8 D 12 D S 29 C 2 8 D 15 D S D 15 D S 29 B 2 8 D 15 D S 29 C 2 8 D 15 D S 29 D 2 8 D 15 D S 29 E 2 8 D 18 D S D 18 D S 29 B 2 8 D 18 D S 29 C 2 8 D 18 D S 29 D 2 8 D 18 D S 29 E 2 8 D 20 D S D 20 D S 29 B 2 8 D 20 D S 29 C 2 8 D 22 D S D 22 D S 29 B 2 8 D 22 D S 29 C 2 8 D 25 D S D 25 D S 29 B 2 8 D 25 D S 29 C 2 8 D 25 D S 29 D 2 8 D 25 D S 29 E 2 8 D 28 D S D 28 D S 29 B 2 8 D 28 D S 29 C 2 8 D 30 D S D 30 D S 29 B 2 8 D 30 D S 29 C 2 8 D 30 D S 29 D 2 8 D 30 D S 29 E 2 8 D 31 D S D 31 D S 29 B 2 8 D 31 D S 29 C 2 8 D 31 D S 29 D 2 8 D 31 D S 29 E 2 8 D 35 D S D 35 D S 29 B 2 8 D 35 D S 29 C 2 8 D 36 D S D 36 D S 29 B 2 8 D 36 D S 29 C 2 8 D 40 D S D 40 D S 29 B 2 8 D 40 D S 29 C 2 8 D 43 D S D 43 D S 29 B 2 8 D 43 D S 29 C 2 8 D 44 D S D 44 D S 29 B 2 8 D 44 D S 29 C 2 8 D 50 D S D 50 D S 29 B 2 8 D 50 D S 29 C 2 8 D 50 D S 29 D 2 8 D 50 D S 29 E 2 8 D 60 D S D 60 D S 29 B 2 8 D 60 D S 29 C 2 8 D 65 D S D 65 D S 29 B 2 8 D 65 D S 29 C 2 8 D 65 D S 29 D 2 8 D 65 D S 29 E 2 8 D 10 D S D 10 D S 29 B 3 8 D 10 D S 29 C 3 8 D 10 D S 29 D 3 8 D 10 D S 29 E 3 8 D 12 D S D 12 D S 29 B 3 8 D 12 D S 29 C 3 8 D 15 D S D 15 D S 29 B 3 8 D 15 D S 29 C 3 8 D 15 D S 29 D 3 8 D 15 D S 29 E 3 8 D 18 D S D 18 D S 29 B 3 8 D 18 D S 29 C 3 8 D 18 D S 29 D 3 8 D 18 D S 29 E 3 8 D 20 D S D 20 D S 29 B 3 8 D 20 D S 29 C 3 8 D 22 D S D 22 D S 29 B 3 8 D 22 D S 29 C 3 8 D 25 D S D 25 D S 29 B 3 8 D 25 D S 29 C 3 8 D 35 D S 29 D 3 8 D 35 D S 29 E 3 8 D 28 D S D 28 D S 29 B 3 8 D 28 D S 29 C 3 8 D 30 D S D 30 D S 29 B 3 8 D 30 D S 29 C 3 8 D 30 D S 29 D 3 8 D 30 D S 29 E 3 8 D 31 D S D 31 D S 29 B 3 8 D 31 D S 29 C 3 8 D 31 D S 29 D 3 8 D 31 D S 29 E 3 8 D 35 D S D 35 D S 29 B 3 8 D 35 D S 29 C 3 8 D 36 D S D 36 D S 29 B 3 8 D 36 D S 29 C 3 8 D 40 D S D 40 D S 29 B 3 8 D 40 D S 29 C 3 8 D 43 D S D 43 D S 29 B 3 8 D 43 D S 29 C 3 43

44 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row D i m e n s i o n s No. of D u a l R e a d o u t P o s i t i o n s B C D E Tail Length.220" [5.59] (DIM J ) (Continued) Tail Length.560" [14.22] (DIM J ) for Wire Wrap Termination Mounting Ear Options C e n t e r e d C e n t e r e d N o Flush F l u s h Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t 8 D 44 D S D 44 D S 29 B 3 8 D 44 D S 29 C 3 8 D 50 D S D 50 D S 29 B 3 8 D 50 D S 29 C 3 8 D 50 D S 29 D 3 8 D 50 D S 29 E 3 8 D 60 D S D 60 D S 29 B 3 8 D 60 D S 29 C 3 8 D 65 D S D 65 D S 29 B 3 8 D 65 D S 29 C 3 8 D 65 D S 29 D 3 8 D 65 D S 29 E 3 8 D 10 W W D 10 W W 29 B 3 8 D 12 W W D 12 W W 29 B 3 8 D 15 W W D 15 W W 29 B 3 8 D 18 W W D 18 W W 29 B 3 8 D 20 W W D 20 W W 29 B 3 8 D 22 W W D 22 W W 29 B 3 8 D 25 W W D 25 W W 29 B 3 8 D 28 W W D 28 W W 29 B 3 8 D 30 W W D 30 W W 29 B 3 8 D 31 W W D 31 W W 29 B 3 8 D 35 W W D 35 W W 29 B 3 8 D 36 W W D 36 W W 29 B 3 8 D 40 W W D 40 W W 29 B 3 8 D 43 W W D 43 W W 29 B 3 8 D 44 W W D 44 W W 29 B 3 8 D 50 W W D 50 W W 29 B 3 8 D 60 W W D 60 W W 29 B 3 8 D 65 W W D 65 W W 29 B 3 44

45 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Modified Bellows Connectors x.200 [2.54 x 5.08] and x.150 [2.54 x 3.81] Right ngle Dip Solder Tails.14±.01 [3.56±.25].025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method 204 Related Product Data: Polarization Key page 57 Daughter Card Edge Pattern page [9.35].128 [3.25] Dia. Dim G Dim K [2.54] [2.54] Ref..040±.003 [1.02±.08] Dia. SECTION X-X Dim G - Centered Mounting Ear [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear [3.18] Cross Drilled Hole Only C B Dim E D Dim B E Dim H Row to Row Spacing SECTION X-X ROTTED 90º.054±.071 [1.37±1.890] PC Board.250 [6.35] Mounting Styles.250 [6.35].610 [15.49] Ref..610 [15.49] Ref..610 [15.49] Ref..180 [4.57] Centered Mounting Ear [3.18] Thru Hole No Mounting Ears.180 [4.57] Centered Mounting Ear [3.18] Cross Drilled Hole.250 [6.35] Flush Mounting Ear [3.18] Cross Drilled Hole 45

46 Ordering Information " [2.54] Centerline /.200" [5.08] Row-to-Row (Dim. H ) Spacing D i m e n s i o n s Mounting Ear Options No. of D u a l C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h R e a d o u t M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear B C D E P o s i t i o n s Ear Only Ear Only " [3.18] E a r s " [3.18] " [3.18] G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole D 10 R 29 8 D 10 R 29 C 8 D 10 R 29 E 8 D 10 R 29 F D 12 R 29 8 D 12 R 29 C 8 D 12 R 29 E D 15 R 29 8 D 15 R 29 C 8 D 15 R 29 E 8 D 15 R 29 F D 18 R 29 8 D 18 R 29 C 8 D 18 R 29 E 8 D 18 R 29 F D 20 R 29 8 D 20 R 29 C 8 D 20 R 29 E D 22 R 29 8 D 22 R 29 C 8 D 22 R 29 E D 25 R 29 8 D 25 R 29 C 8 D 25 R 29 E 8 D 25 R 29 F D 28 R 29 8 D 28 R 29 C 8 D 28 R 29 E D 30 R 29 8 D 30 R 29 C 8 D 30 R 29 E 8 D 30 R 29 F D 31 R 29 8 D 31 R 29 C 8 D 31 R 29 E 8 D 31 R 29 F D 35 R 29 8 D 35 R 29 C 8 D 35 R 29 E D 36 R 29 8 D 36 R 29 C 8 D 36 R 29 E D 40 R 29 8 D 40 R 29 C 8 D 40 R 29 E D 43 R 29 8 D 43 R 29 C 8 D 43 R 29 E D 44 R 29 8 D 44 R 29 C 8 D 44 R 29 E D 50 R 29 8 D 50 R 29 C 8 D 50 R 29 E 8 D 50 R 29 F D 60 R 29 8 D 60 R 29 C 8 D 60 R 29 E D 65 R 29 8 D 65 R 29 C 8 D 65 R 29 E 8 D 65 R 29 F 46

47 Ordering Information " [2.54] Centerline /.150" [3.81] Row-to-Row (Dim. H ) Spacing D i m e n s i o n s Mounting Ear Options No. of D u a l C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h R e a d o u t M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear B C D E P o s i t i o n s Ear Only Ear Only " [3.18] E a r s " [3.18] " [3.18] G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole D 10 R 29 M D 10 R 29 C M D 10 R 29 E M D 10 R 29 F M D 12 R 29 M D 12 R 29 C M D 12 R 29 E M D 15 R 29 M D 15 R 29 C M D 15 R 29 E M D 15 R 29 F M D 18 R 29 M D 18 R 29 C M D 18 R 29 E M D 18 R 29 F M D 20 R 29 M D 20 R 29 C M D 20 R 29 E M D 22 R 29 M D 22 R 29 C M D 22 R 29 E M D 25 R 29 M D 25 R 29 C M D 25 R 29 E M D 25 R 29 F M D 28 R 29 M D 28 R 29 C M D 28 R 29 E M D 30 R 29 M D 30 R 29 C M D 30 R 29 E M D 30 R 29 F M D 31 R 29 M D 31 R 29 C M D 31 R 29 E M D 31 R 29 F M D 35 R 29 M D 35 R 29 C M D 35 R 29 E M D 36 R 29 M D 36 R 29 C M D 36 R 29 E M D 40 R 29 M D 40 R 29 C M D 40 R 29 E M D 43 R 29 M D 43 R 29 C M D 43 R 29 E M D 44 R 29 M D 44 R 29 C M D 44 R 29 E M D 50 R 29 M D 50 R 29 C M D 50 R 29 E M D 50 R 29 F M D 60 R 29 M D 60 R 29 C M D 60 R 29 E M D 65 R 29 M D 65 R 29 C M D 65 R 29 E M D 65 R 29 F M

48 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Modified Bellows Connectors x.250 [3.18 x 6.35], Centerline Straight Dip Solder and Wire Wrap Ta i l s.610 [5.49].054±.071 [1.37±1.890] PC Board.300 [7.62] Card Depth Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum.368 [9.35] C [3.18] Ref. D SECTION X-X SECTION X-X ROTTED 90º.025 [.64] Sq..250 [6.35] J Electrical Properties: Operation Voltage 600 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: B E Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method [3.25] Dia. P ±.003 [±.080] Dia. Dim E Dim B Related Product Data: Polarization Key page 57 Daughter Card Edge Pattern page 57 [3.18] P=.040 [1.02] Dip Solder pplications P=.042 [1.07] For Wire Wrap pplications.250 [6.35].250 [6.35].610 [15.49] Ref. Mounting Styles.250 [6.35].180 [4.57] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 48

49 Ordering Information " [3.18] Centerline /.250" [6.35] Row-to-Row Dip Solder Mounting Ear Options No. of D u a l D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h R e a d o u t Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear P o s i t i o n s B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.160" [4.06] (DIM J ) D 06 D S D 06 D S 29 B 2 7 D 06 D S 29 C 2 7 D 06 D S 29 D 2 7 D 06 D S 29 E D 10 D S D 10 D S 29 B 2 7 D 10 D S 29 C 2 7 D 10 D S 29 D 2 7 D 10 D S 29 E D 15 D S D 15 D S 29 B 2 7 D 15 D S 29 C 2 7 D 15 D S 29 D 2 7 D 15 D S 29 E D 18 D S D 18 D S 29 B 2 7 D 18 D S 29 C 2 7 D 18 D S 29 D 2 7 D 18 D S 29 E D 22 D S D 22 D S 29 B 2 7 D 22 D S 29 C D 25 D S D 25 D S 29 B 2 7 D 25 D S 29 C 2 7 D 25 D S 29 D 2 7 D 25 D S 29 E D 28 D S D 28 D S 29 B 2 7 D 28 D S 29 C D 30 D S D 30 D S 29 B 2 7 D 30 D S 29 C 2 7 D 30 D S 29 D 2 7 D 30 D S 29 E D 35 D S D 35 D S 29 B 2 7 D 35 D S 29 C D 36 D S D 36 D S 29 B 2 7 D 36 D S 29 C D 40 D S D 40 D S 29 B 2 7 D 40 D S 29 C D 43 D S D 43 D S 29 B 2 7 D 43 D S 29 C D 50 D S D 50 D S 29 B 2 7 D 50 D S 29 C 2 7 D 50 D S 29 D 2 7 D 50 D S 29 E 2 " [3.18] Centerline /.250" [6.35] Row-to-Row Wire Wrap Mounting Ear Options No. of D u a l D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h R e a d o u t Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear P o s i t i o n s B C D E " [3.18] 4-40 Threaded E a r s " [3.18] 4-40 Threaded Thru Hole i n s e r t Thru Hole i n s e r t Tail Length.560" [14.22] (DIM J ) D 06 W W D 06 W W 29 B D 10 W W D 10 W W 29 B D 15 W W D 15 W W 29 B D 18 W W D 18 W W 29 B D 22 W W D 22 W W 29 B D 25 W W D 25 W W 29 B D 28 W W D 28 W W 29 B D 30 W W D 30 W W 29 B D 35 W W D 35 W W 29 B D 36 W W D 36 W W 29 B D 40 W W D 40 W W 29 B D 43 W W D 43 W W 29 B D 50 W W D 50 W W 29 B 3 49

50 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Modified Bellows Connectors x.250 [3.18 x 6.35], x.150 [3.18 x 3.81], x.200 [3.18 x 5.08] Centerline, Right ngle Ta i l s.14±.01 [3.56±.25].025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties: Operation Voltage 1000 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method 204 Related Product Data: Polarization Key page 57 Daughter Card Edge Pattern page [9.35].128 [3.25] Dia. Dim G Dim K [3.18] [3.18] REF SECTION X-X Dim G - Centered Mounting Ear [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear [3.18] Cross Drilled Hole Only C B Dim E.040±.003 [1.02±.08] Dia. D Dim B.054±.071 [1.37±1.890] PC Board SECTION X-X ROTTED 90º E Dim H Row to Row Spacing Mounting Styles.250 [6.35].250 [6.35].610 [15.49] Ref..610 [15.49] Ref..610 [15.49] Ref..180 [4.57] Centered Mounting Ear [3.18] Thru Hole No Mounting Ears Centered Mounting Ear.180 [3.18] Thru Hole [4.57] [6.35] Flush Mounting Ear [3.18] Cross Drilled Hole

51 Ordering Information " [3.18] Centerline /.200" [5.08] and.150" [3.81] Row-to-Row (Dim. H ) Spacing D i m e n s i o n s Mounting Ear Options No. of D u a l C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h R e a d o u t M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear B C D E P o s i t i o n s Ear Only Ear Only " [3.18] E a r s " [3.18] " [3.18] G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole.150" [3.81] Row-to-Row (Dim. H ) Spacing D 06 R 29 M D 06 R 29 C M D 06 R 29 E M D 06 R 29 F M D 10 R 29 M D 10 R 29 C M D 10 R 29 E M D 10 R 29 F M D 15 R 29 M D 15 R 29 C M D 15 R 29 E M D 15 R 29 F M D 18 R 29 M D 18 R 29 C M D 18 R 29 E M D 18 R 29 F M D 22 R 29 M D 22 R 29 C M D 22 R 29 E M D 22 R 29 F M D 25 R 29 M D 25 R 29 C M D 25 R 29 E M D 25 R 29 F M D 28 R 29 M D 28 R 29 C M D 28 R 29 E M D 28 R 29 F M D 30 R 29 M D 30 R 29 C M D 30 R 29 E M D 30 R 29 F M D 35 R 29 M D 35 R 29 C M D 35 R 29 E M D 35 R 29 F M D 36 R 29 M D 36 R 29 C M D 36 R 29 E M D 36 R 29 F M D 40 R 29 M D 40 R 29 C M D 40 R 29 E M D 40 R 29 F M D 43 R 29 M D 43 R 29 C M D 43 R 29 E M D 43 R 29 F M D 50 R 29 M D 50 R 29 C M D 50 R 29 E M D 50 R 29 F M " [5.08] Row-to-Row (Dim. H ) Spacing D 06 R 29 M D 06 R 29 C M D 06 R 29 E M D 06 R 29 F M D 10 R 29 M D 10 R 29 C M D 10 R 29 E M D 10 R 29 F M D 15 R 29 M D 15 R 29 C M D 15 R 29 E M D 15 R 29 F M D 18 R 29 M D 18 R 29 C M D 18 R 29 E M D 18 R 29 F M D 22 R 29 M D 22 R 29 C M D 22 R 29 E M D 22 R 29 F M D 25 R 29 M D 25 R 29 C M D 25 R 29 E M D 25 R 29 F M D 28 R 29 M D 28 R 29 C M D 28 R 29 E M D 28 R 29 F M D 30 R 29 M D 30 R 29 C M D 30 R 29 E M D 30 R 29 F M D 35 R 29 M D 35 R 29 C M D 35 R 29 E M D 35 R 29 F M D 36 R 29 M D 36 R 29 C M D 36 R 29 E M D 36 R 29 F M D 40 R 29 M D 40 R 29 C M D 40 R 29 E M D 40 R 29 F M D 43 R 29 M D 43 R 29 C M D 43 R 29 E M D 43 R 29 F M D 50 R 29 M D 50 R 29 C M D 50 R 29 E M D 50 R 29 F M

52 Ordering Information " [3.18] Centerline /.250" [6.35] Row-to-Row (Dim. H ) Spacing D i m e n s i o n s Mounting Ear Options No. of D u a l C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h R e a d o u t M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear B C D E P o s i t i o n s Ear Only Ear Only " [3.18] E a r s " [3.18] " [3.18] G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole.250" [6.35] Row-to-Row (Dim. H ) Spacing D 06 R 29 7 D 06 R 29 C 7 D 06 R 29 E 7 D 06 R 29 F D 10 R 29 7 D 10 R 29 C 7 D 10 R 29 E 7 D 10 R 29 F D 15 R 29 7 D 15 R 29 C 7 D 15 R 29 E 7 D 15 R 29 F D 18 R 29 7 D 18 R 29 C 7 D 18 R 29 E 7 D 18 R 29 F D 22 R 29 7 D 22 R 29 C 7 D 22 R 29 E 7 D 22 R 29 F D 25 R 29 7 D 25 R 29 C 7 D 25 R 29 E 7 D 25 R 29 F D 28 R 29 7 D 28 R 29 C 7 D 28 R 29 E 7 D 28 R 29 F D 30 R 29 7 D 30 R 29 C 7 D 30 R 29 E 7 D 30 R 29 F D 35 R 29 7 D 35 R 29 C 7 D 35 R 29 E 7 D 35 R 29 F D 36 R 29 7 D 36 R 29 C 7 D 36 R 29 E 7 D 36 R 29 F D 40 R 29 7 D 40 R 29 C 7 D 40 R 29 E 7 D 40 R 29 F D 43 R 29 7 D 43 R 29 C 7 D 43 R 29 E 7 D 43 R 29 F D 50 R 29 7 D 50 R 29 C 7 D 50 R 29 E 7 D 50 R 29 F 52

53 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Modified Bellows Connectors,.156 x.200 [3.96 x 5.08] Centerline, Straight Dip Solder and Wire Wrap Ta i l s.610 [5.49] SECTION X-X ROTTED 90º.054±.071 [1.37±1.890 ] PC Board.300 [7.62] Card Depth J Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum.368 [9.35] C.156 [3.96] Ref. D.025 [.64] Sq. SECTION X-X.200 [5.08] Electrical Properties: Operation Voltage 1500 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms B E Environmental Properties: Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method 204 Related Product Data: Polarization Key page 57 Daughter Card Edge Pattern page [3.25] Dia..156 [3.25] Dim E P±.003 [.08] Dia. Dim B P=.040 [1.02] Dip Solder pplications P=.042 [1.07] For Wire Wrap pplications.200 [5.08].250 [6.35] Mounting Styles.610 [15.49] Ref..180 [4.57] Centered Mounting Ear [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears 53

54 Ordering Information.156" [3.96] Centerline /.200" [5.08] Row-to-Row Mounting Ear Options No. of D u a l D i m e n s i o n s C e n t e r e d C e n t e r e d N o R e a d o u t Mounting Ear Mounting Ear M o u n t i n g B C D E P o s i t i o n s " [3.18] Thru 4-40 Threaded E a r s H o l e I n s e r t Tail Length.160" [4.06] (DIM J ) D 06 D S D 06 D S 29 B 2 6 D 06 D S 29 C D 10 D S D 10 D S 29 B 2 6 D 10 D S 29 C D 12 D S D 12 D S 29 B 2 6 D 12 D S 29 C D 15 D S D 15 D S 29 B 2 6 D 15 D S 29 C D 18 D S D 18 D S 29 B 2 6 D 18 D S 29 C D 22 D S D 22 D S 29 B 2 6 D 22 D S 29 C D 25 D S D 25 D S 29 B 2 6 D 25 D S 29 C D 28 D S D 28 D S 29 B 2 6 D 28 D S 29 C D 36 D S D 36 D S 29 B 2 6 D 36 D S 29 C D 43 D S D 43 D S 29 B 2 6 D 43 D S 29 C 2 Tail Length.220" [5.59] (DIM J ) D 06 D S D 06 D S 29 B 3 6 D 06 D S 29 C D 10 D S D 10 D S 29 B 3 6 D 10 D S 29 C D 12 D S D 12 D S 29 B 3 6 D 12 D S 29 C D 15 D S D 15 D S 29 B 3 6 D 15 D S 29 C D 18 D S D 18 D S 29 B 3 6 D 18 D S 29 C D 22 D S D 22 D S 29 B 3 6 D 22 D S 29 C D 25 D S D 25 D S 29 B 3 6 D 25 D S 29 C D 28 D S D 28 D S 29 B 3 6 D 28 D S 29 C D 36 D S D 36 D S 29 B 3 6 D 36 D S 29 C D 43 D S D 43 D S 29 B 3 6 D 43 D S 29 C 3 Tail Length.560" [14.22] (DIM J ) For Wire Wrap Termination D 06 W W D 06 W W 29 B D 10 W W D 10 W W 29 B D 12 W W D 12 W W 29 B D 15 W W D 15 W W 29 B D 18 W W D 18 W W 29 B D 22 W W D 22 W W 29 B D 25 W W D 25 W W 29 B D 28 W W D 28 W W 29 B D 36 W W D 36 W W 29 B D 43 W W D 43 W W 29 B 3 54

55 Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 Certified by Canadian Standards ssociation, File No. LR49571 Modified Bellows Connectors.156 x.200 [3.96 x 5.08] Centerline,.156 x.150 [3.96 x 3.81], Right ngle, Dip Solder Ta i l s.14±.01 [3.56±.25].025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card) 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using.0620 [1.57] steel blade. Insulator Body Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color Black Contacts High strength copper alloy. Contact Plating [ ] nickel underplate with [ ] gold in the mating area, tin/lead on tails, [ ] minimum Electrical Properties:.368 [9.35] C.156 [3.96] REF SECTION X-X D.054±.071 [1.37±1.890] PC Board SECTION X-X ROTTED 90º Operation Voltage 1500 VDC (sea level) Current Rating 3 mperes Initial Contact Resistance 10 milliohms Environmental Properties: B E Operating Temperature -55 C to +125 C Temperature Cycling MIL-STD-202 method 107 Vibration MIL-STD-202 method 204 Related Product Data:.128 [3.25] Dia. Dim E.040±.003 [1.02±.08] Dia. Dim B Polarization Key page 57 Daughter Card Edge Pattern page 57 Dim G Dim K.156 [3.96] Dim H Row to Row Spacing Dim G - Centered Mounting Ear [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear [3.18] Cross Drilled Hole Only.250 [6.35].250 [6.35] Mounting Styles.610 [15.49] Ref..610 [15.49] Ref..610 [15.49] Ref..180 [4.57] Centered Mounting Ear [3.18] Thru Hole No Mounting Ears Centered Mounting Ear [3.18] Thru Hole Flush Mounting Ear [3.18] Cross Drilled Hole 55

56 Ordering Information.156" [3.96] Centerline /.200" [5.08] and.150" [3.81] Row-to-Row (Dim. H ) Spacing D i m e n s i o n s Mounting Ear Options No. of D u a l C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h R e a d o u t B C D E M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear P o s i t i o n s Ear Only Ear Only " [3.18] E a r s " [3.18] " [3.18] G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole.200" [5.08] Row-to-Row (Dim. H ) Spacing D 06 R 29 6 D 06 R 29 C 6 D 06 R 29 E 6 D 06 R 29 F D 10 R 29 6 D 10 R 29 C 6 D 10 R 29 E 6 D 10 R 29 F D 12 R 29 6 D 12 R 29 C 6 D 12 R 29 E 6 D 12 R 29 F D 15 R 29 6 D 15 R 29 C 6 D 15 R 29 E 6 D 15 R 29 F D 18 R 29 6 D 18 R 29 C 6 D 18 R 29 E 6 D 18 R 29 F D 22 R 29 6 D 22 R 29 C 6 D 22 R 29 E 6 D 22 R 29 F D 25 R 29 6 D 25 R 29 C 6 D 25 R 29 E 6 D 25 R 29 F D 28 R 29 6 D 28 R 29 C 6 D 28 R 29 E 6 D 28 R 29 F D 36 R 29 6 D 36 R 29 C 6 D 36 R 29 E 6 D 36 R 29 F D 40 R 29 6 D 40 R 29 C 6 D 40 R 29 E 6 D 40 R 29 F D 43 R 29 6 D 43 R 29 C 6 D 43 R 29 E 6 D 43 R 29 F.150" [3.81] Row-to-Row (Dim. H ) Spacing D 06 R 29 M D 06 R 29 C M D 06 R 29 E M D 06 R 29 F M D 10 R 29 M D 10 R 29 C M D 10 R 29 E M D 10 R 29 F M D 12 R 29 M D 12 R 29 C M D 12 R 29 E M D 12 R 29 F M D 15 R 29 M D 15 R 29 C M D 15 R 29 E M D 15 R 29 F M D 18 R 29 M D 18 R 29 C M D 18 R 29 E M D 18 R 29 F M D 22 R 29 M D 22 R 29 C M D 22 R 29 E M D 22 R 29 F M D 25 R 29 M D 25 R 29 C M D 25 R 29 E M D 25 R 29 F M D 28 R 29 M D 28 R 29 C M D 28 R 29 E M D 28 R 29 F M D 36 R 29 M D 36 R 29 C M D 36 R 29 E M D 36 R 29 F M D 40 R 29 M D 40 R 29 C M D 40 R 29 E M D 40 R 29 F M D 43 R 29 M D 43 R 29 C M D 43 R 29 E M D 43 R 29 F M

57 Card Edge Polarization Keys Description/pplication Tyco Electronics can provide polarization keys in the basic configuration shown on this page. Our Modified Bellows and Cantilever Beam Series Card Edge Connectors use these keys. The part number and the connector series for which it was designed are listed in the table below. Break Off Point [6.10].033 [.84].19 [4.83] Ordering Information cquired Part Used on Connector Shown on Number Series Pages Modified Bellows Cantilever Beam Card Edge Connectors Recommended Daughter Card Edge Pattern Per MIL-C-21097E.062 [1.57] Board Thickness 30 Slot Depth Min. Dim. Dim. B Contact Spacing (Per pplicable Catalog Page).015 [.38] See Note 3 Daughter Card Contact Spacing Dim Non-ccum. ±.005 (.13) Dim B [2.54].093 [2.36].052 [1.32] [3.18].093 [2.36].052 [1.32].156 [3.96].105* [2.67].094 [2.39] * Except MIL-C-21097E 8 4 which is.070 [1.78] NOTES: 1. Dimensions are in inches 2. Unless otherwise specified, tolerance is ±.005 [0.13 mm] for three place decimals. 3. Number of contact fingers shall be the same as the corresponding printed wiring connector. 57

58 Low Profile Connectors Product Facts Low profile housing is.460 [11.68] deep 6 through 43 dual positions on.156 [3.96] centerline; 6 though 50 dual positions on [3.18] centerline Solder eyelet for wire-toboard or solder post for mother-daughter board application Selective gold plating of contact area for high performance at low cost lternate platings are available on request Contacts bifurcated for redundancy Tin plate for high solderability of solder eyelets and posts ccepts [ ] thick printed circuit boards Housings available with or without mounting ears Intercontact keying available UL 94V-0 rated, glass-filled polyester housings Variety of solder post lengths 5 ampere current rating per contact* Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 For printed circuit board packaging, MP Low Profile Edge Connectors provide high performance, low cost connections on [3.18] and.156 [3.96] centerline spacings. [2.54] centerline connectors can be made available, consult Tyco Electronics. Mounted connector housings extend only.460 [11.68] from the mother board to allow efficient use of available space. These low profile connectors are available in 6 through 43 dual position sizes on.156 [3.96] centerline spacing and with 6 through 50 dual positions on [3.18] centers. Connectors are supplied with either solder posts for mother-daughter board applications or solder eyelet contacts for wire-toboard use. Low Profile Edge Connectors feature clear slot entry and accept [ ] thick doublesided printed circuit boards. Solder posts are available with.150 [3.18] and.180 [4.57] long tails on.140 [3.56] or.200 [5.08] rowto-row spacing. Impact-resistant thermoplastic housing, UL rated 94V-0, have molded-in cavity identification and are available with or without mounting ears. dditional features of the housings include intercontact keying provisions, probe slots and identification of number one position. The precision formed contacts made of phosphor bronze are gold plated on the contact mating surface only. This selective plating provides high reliability while maintaining low cost. Solder eyelets and posts are tin plated for excellent solderability. The contact is bifurcated for redundancy. Shorting contacts are available. ll connector configurations are furnished preloaded. Selectively loaded connectors can be made available for added economy. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 58

59 Low Profile Connectors, [3.18] Centerline Material and Finish: Housing Green, glass-filled polyester Contacts Phosphor bronze, duplex plated [ ] gold in contact area; [ ] bright tin on posts, with entire contact underplated [ ] nickel Related Product Data: Keying Plug page 63 PC Board Hole Layouts See below PC Board Edge Pattern page 63 Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [3.18] PCBoard Thickness [ ] [3.18] Typ. B D.128 [3.25] Dia. 2 (Plcs.).150 [3.81].300 [7.62].460 [11.68].250 [6.35] C #1 Cavity Identification [3.18] Typ. Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) B C D E F E.295 [7.49] [3.18] R e f..295 [7.49] [3.18] R e f..295 [7.49] [3.18] R e f..165 [4.19] Post Length (See Chart).200 [5.08] Flow Solder Post.200 [5.08] Row-to-Row Spacing.165 [4.19] Post Length (See Chart).140 [3.56] Flow Solder Post.140 [3.56] Row-to-Row Spacing.165 [4.19].280 [7.11] Ref..235 [5.97] Ref. Solder Eyelet Contact.235 [5.97] Row-to-Row Spacing [3.25] Dia..052 [1.32] Dia..128 [5.08] [3.25] Dia..052 [1.32] Dia..140 [3.56].335 [8.51] Typ. [3.18] B [2.54].335 [8.51] Typ. [3.18] B.070 [1.78] Recommended PC Board Hole Layout Recommended PC Board Hole Layout 59

60 Low Profile Connectors, [3.18] Centerline (Continued) Flow Solder Post.200 [5.08] Row-to-Row Spacing No. of Dimensions Post With Without Dual Mounting Mounting Positions B C D E Length* Ears Ears Flow Solder Post.140 [3.56] Row-to-Row Spacing No. of Dimensions Post With Without Dual Mounting Mounting Positions B C D E Length* Ears Ears Solder Eyelet Contact.235 [5.97] Row-to-Row Spacing No. of Dimensions With Dual Mounting Positions B C D E Ears *Metric equivalents for post length are.150 = [3.81];.180 = [4.57]. Note: Other connector sizes can be made available, consult Tyco Electronics. 60

61 Low Profile Connectors,.156 [3.96] Centerline Material and Finish: Housing Green, glass-filled polyester Contacts Phosphor bronze, duplex plated [ ] gold in contact area; [ ] bright tin on posts, with entire contact underplated [ ] nickel Insert Brass Related Product Data: Keying Plug page 63 PC Board Hole Layouts See below PC Board Edge Pattern page 63 Mounting Ear with Insert Threaded Inserts 4-40 NC-2B (2 per connector) PCBoard Thickness [ ].160 [4.06].156 [3.96] Typ. B D.128 [3.25] Dia. (2 Plcs.).150 [3.81].300 [7.62] C Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [6.35].460 [11.68] #1 Cavity Identification.156 [3.96] Typ. Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) B C D E F E.295 [7.49] [3.18] Ref..295 [7.49] [3.18] Ref..295 [7.49] [3.18] Ref..165 [4.19] Post Length (See Chart).200 [5.08] Flow Solder Post.200 [5.08] Row-to-Row Spacing.165 [4.19] Post Length (See Chart).140 [3.56] Flow Solder Post.140 [3.56] Row-to-Row Spacing.165 [4.19].280 [7.11] Ref..235 [5.97] Ref. Solder Eyelet Contact.235 [5.97] Row-to-Row Spacing [3.25] Dia..052 [1.32] Dia..128 [5.08] [3.25] Dia..052 [1.32] Dia..140 [3.56].378 [9.59] Typ..156 [3.96] B [2.54].378 [9.59] Typ..156 [3.96] B.070 [1.78] Recommended PC Board Hole Layout Recommended PC Board Hole Layout 61

62 Low Profile Connectors,.156 [3.96] Centerline (Continued) Flow Solder Post.200 [5.08] Row-to-Row Spacing No. of Dimensions Post With With Without Dual Mounting Mounting Ears Mounting Positions B C D E Length* Ears and Inserts Ears Flow Solder Post.140 [3.56] Row-to-Row Spacing and Solder Eyelet Contact.235 [5.97] Row-to-Row Spacing Flow Solder Post Solder Eyelet Contact No. of Dimensions Dual Post With Without With Without Positions B C D E Length* Mounting Mounting Mounting Mounting Ears Ears Ears Ears *Metric equivalents for post length are.150 = [3.81];.180 = [4.57]. 1For.040 [1.02] diameter hole. Note: Other connector sizes can be made available, consult Tyco Electronics

63 Low Profile Connectors (Continued) Keying Plug Intercontact Key Material: Glass-filled nylon Part No Recommended PC Board Edge Patterns [3.18] Centerline Boards Intercontact KeySlot.050 [1.27].300 [7.52] Min..400 [10.16] [3.18] [3.18].078± [1.98± 0.13 ] [4.45] Min. Recommended Gold rea.156 [3.96] Centerline Boards Intercontact KeySlot.050 [1.27].300 [7.52] Min..400 [10.16].160 [4.06].156 [3.96].094± [2.39± 0.13 ] [4.45] Min. Recommended Gold rea 63

64 Twin Leaf Mother Board Connectors Product Facts Wide variety of sizes available from 3 dual positions and up no initial tooling investment required for new versions Connectors can be selectively loaded with contacts in custom patterns Connectors tooled on all standard centerlines [2.54], [3.18],.150 [3.81],.156 [3.96], and.200 [5.08] Note:.200 [5.08] centerline capabilities provided by loading every-other dual position of [2.54] centerline housings. Closed card entry protects contacts and daughter board pads dapts to a wide range of mother board thicknesses to.104 [2.64] maximum Phosphor bronze contacts selectively plated for top performance and maximum economy Protective channel helps prevent overstress of contacts Daughter board keying available in intercontact or on-contact styles Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 *Consult Tyco Electronics engineering when paralleling contacts for power applications. The MP Twin Leaf Connector is a highly reliable, low-cost mother/ daughter board connector designed for solid-state circuitry. The one-piece, multi-contact connector requires no front-end tooling. This versatile connector for double-sided printed circuit boards uses preloaded contacts and selective plating to give lowest applied cost. Critical contact areas are gold-over-nickel plated to provide positive electrical connection between contacts and daughter board pads. Contact posts are tin plated for efficient dip soldering to mother boards up to.104 [2.64] thick. The Twin Leaf Connector delivers high reliability because the contacts possess superior tolerance of environmental stresses including shock, vibration and variations of temperature and humidity. Other characteristics such as high insulation resistance, low termination resistance, long life and moderate contact separation force meet industry requirements for reliability. Connectors are tooled in sizes from 3 through 80 dual-contact positions with contacts on [2.54], [3.18],.150 [3.81],.156 [3.96] or.200 [5.08] centers. Other sizes and customloaded contact patterns are available on request. The connector housing, made of glass-filled polyester with a UL 94V-0 rating, features a standoff which facilitates the use of a probe for electrical continuity checks without risk of damage to the contacts. closed card-entry design of the housing protects the contacts and daughter board pads. Housings accept daughter boards ranging from.055 [1.40] to.070 [1.78] in thickness. Intercontact and on-contact keys are available for polarization of the housings. Card guides or end caps make alignment of daughter board pads with Twin Leaf Connector contacts quick and easy. Performance Specifications Contact Rating*: 3 amperes continuous Temperature Rating: 55 C to +105 C Insulation Resistance: 5,000 megohms Dielectric Withstanding Voltage: Test Voltage (C, RMS) ltitude Contact Spacing [2.54].150 [3.81] Sea Level 1,000 1,500 50,000 ft m ,000 ft m Termination Resistance: 10 milliohms, max. Durability: Tested to 100 cycles (engage/withdraw) Contact Plating: [ ] selective gold plating on contact area; bright tin on solder tine 64

65 Twin Leaf Mother Board Connectors Without End Caps [2.54], [3.18],.150 [3.81] and.156 [3.96] Centerlines, With Solder Posts.400 [10.16] Fit for [ ] PCBoard Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold in contact area; tin on posts, with entire contact underplated [ ] nickel, except where noted Related Product Data: Performance Specifications page 64 Card Guides pages 70, 71 Keying Plugs page 72 PC Board Hole Layouts page 71 Card Slot Depth.400 [10.16] Max..135*.170* [3.43] or [4.32] *Post length: B D.010 x.024 [0.25 x 0.61] Post for.035 [0.89] Dia. Hole.135 [3.43] for.150 [3.81] and.156 [3.96] centerlines, except where noted;.170 [4.32] for [2.54] and [3.18] centerlines, except where noted..225 [5.72].200 [5.08].610 [15.49] Technical Documents: (pages 186, 187): Product Specification Instruction Sheets , ,

66 Twin Leaf Mother Board Connectors Without End Caps = [2.54] = [3.18] =.150 [3.81] =.156 [3.96] No. of Centerline Spacing Centerline Spacing Centerline Spacing Centerline Spacing Dual Positions B D Part B D Part B D Part B D Part Numbers Numbers Numbers Numbers , , , Contacts are plated [ ] gold in contact area, tin on posts, with entire contact underplated [ ] nickel. 2Post length.135 [3.43] 3Post length.170 [4.32] Note: Other connector sizes can be made available, consult Tyco Electronics. 66

67 Twin Leaf Mother Board Connectors With End Caps [2.54], [3.18],.150 [3.81] and.156 [3.96] Centerlines, With Solder Posts Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold in contact area; tin on posts, with entire contact underplated [ ] nickel Related Product Data: Performance Specifications page 64 Keying Plugs page 72 PC Board Hole Layouts page 71 Technical Documents: (pages 186, 187): Product Specification Instruction Sheets , , Card Slot Depth.400 [10.16] Max..062 [1.58] F B G E** ccepts #2 Self-tapping Screw **Post length:.135 [3.43] for.150 [3.81] and.156 [3.96] centerlines;.170 [4.32] for [2.54] and [3.18] centerlines. **See page 27 for dimensions..135*.170* [3.43] or [4.32].400 [10.16].200 [5.08] Fit for [ ] PCBoard.225 [5.72].610 [15.49].010 x.024 [0.25 x 0.61] Post for.035 [0.89] Dia. Hole 67

68 Twin Leaf Mother Board Connectors With End Caps No. of = [2.54] Centerline Spacing = [3.18] Centerline Spacing =.150 [3.81] Centerline Spacing =.156 [3.96] Centerline Spacing Dual Part Part Part Part Pos. B F G B F G B F G B F G Numbers Numbers Numbers Numbers Note: Other connector sizes can be made available, consult Tyco Electronics. 68

69 Twin Leaf Mother Board Connectors With End Caps (Continued) Typical Connector and Card Guide ssembly Single Slotted Card Guide Double Slotted Card Guide (Without Stand-off) Double Slotted Card Guide (With Stand-off) End Cap Daughter Board Stand-off Mother Board.104 [2.64] Max. Thickness* Self-tapping #2 Screw (2 Reqd.) Self-tapping #2 Screw (2 Reqd.) Self-tapping #2 Screw (1 Reqd.) *Must be.063 [1.59] thick for use with Double Slotted Card Guides. 69

70 Twin Leaf Mother Board Connectors (Continued) Card Guides Single Slotted Material: Glass-filled nylon, black Part No [5.33] [95.76].170 [4.32] [13.28].225 [1.88] Dia. [5.72] Thru Hole Related Product Data: Connectors used with page [91.06].137 [3.48].074 [1.88] Dia. x.175 [4.45] Deep Technical Documents: (pages 186, 187): Instruction Sheets , Single Slotted Card Guide and Connector Mounting.200 [5.08] [2.54] Connector Centerline.035 [0.89] Dia. Mounting Hole Contact Centerline.091 [2.31] Dia. E Min..225 [5.72] Dimensions E

71 Twin Leaf Mother Board Connectors (Continued) Card Guides (Continued) Material: Nylon, natural Part No Related Product Data: Connectors used with page 65 Technical Documents: (pages 186, 187): Instruction Sheets , Double Slotted Without Stand-off.080 [2.03].540 [13.72].300 [7.62] [42.67] [38.10].400 [10.16].150 [3.81] Double Slotted Card Guide and Connector Mounting.200 [5.08] [2.54] Connector Centerline.035 [0.89] Dia. Mounting Hole Contact Centerline E Min..175 [4.45].310 [7.87] Dimensions E Note: Mother Board must be.063 [1.59] thick for use with Double Slotted Card Guides. Recommended PC Board Layout for Connectors With End Caps.200 [5.08] [2.54] Contact Centerline Connector Centerline.035 [0.89] Dia. Mounting Hole E [2.54] Dia. Dimensions E

72 Twin Leaf Mother Board Connectors (Continued) Keying Plugs Material: Nylon, natural Technical Documents: (pages 186, 187): Instruction Sheet Type Type B Intercontact On-Contact In-Row Type Connector Style* Intercontact Keying Plug On-Contact Keying Plug Contact of with without Type Type B Insertion/Extraction Part Insertion/Extraction Spacing Contact End Caps End Caps Part Numbers Part Numbers Tool Numbers Tool Solder Post Card Extender Solder Post Card Extender Solder Post Wrap-Type Post Card Extender Solder Post Wrap-Type Post Card Extender *Refer to pages 66-68, as applicable, for specific connector sizes..475 [12.06] Min. Connector Dimension Centerlines Intercontact On-Contact Recommended PC Board Cutout for Keying Plugs Other Twin Leaf Mother Board Connectors For more information on the connectors shown here, consult Tyco Electronics. Card Extender Connectors.400 [10.16] Fits for [ ] PCBoard.225 [5.72].610 [15.49] Connectors With End Caps Centerlines Part Number Series* *Consult Tyco Electronicsfor specific connector sizes. 72

73 Rotary Cam ZIF Connectors Product Facts Zero insertion force; little or no effort required to insert and withdraw PC boards Reduced pad wear for extended board life llows all four sides of board to be used for input/output functions ccepts double-sided boards Three contact styles to choose from: vertical solder post, right-angle solder post and wrap-type post (2 and 3 high) vailable in [2.54], [3.18] and.156 [3.96] centerlines Three configurations available: open one end, open both ends and closed both ends Products indicated are recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30 C Operating Temperature: 55 C to +105 C Contact Resistance: 20 milliohms max. Durability: Tested to 5000 cycles MP Rotary Cam Zero Insertion Force (ZIF) Card Edge Connectors are available in sizes to fit most industry-standard printed circuit boards. clockwise rotation of the cam handle opens contacts to allow zero-force insertion or removal of PC boards even boards with a large number of contacts. Turning the cam handle to close the connector locks the board securely in place. Rotary Cam ZIF Connectors accept double-sided PC boards [ ] thick, with contact centerline intervals of [2.54], [3.18] and.156 [3.96]. Row-to-row spacing of connector posts is.200 [5.08] for [2.54] and.156 [3.96] connectors and.250 [6.35] for [3.18] connectors. Contacts are nickel underplated phosphor bronze with gold plate in the contact area and tin-lead plated posts. Contact configurations include vertical and right-angle solder posts and wrap-type posts. Preassembled connectors feature housings made from 94V-0 rated glass-filled polyester and mounting ears for easy mounting to the mother board. Housings are available with one end open, both ends open and both ends closed for side and top daughter board insertion. Integral board locks secure boards in the connectors. ccessories include dust covers, cam rods (with and without boots) and cam keys for nut-driver actuation and for tandem operation of connectors. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 73

74 Rotary Cam ZIF Connectors, x.200 [2.54 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold per MIL-G in contact area; [ ] tin-lead per MIL-P on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Board Lock Feature On connectors open one end and open both ends Daughter PC Board [ ] thick Performance Specifications page 73 Dust Cover page 79 PC Board Hole Layout and Edge Patterns pages 81, 82 Special pplication pages 82, 96 Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [11.18] [27.81] Ref..210 [5.33] Closed End B D C [2.54] Typ..850 [21.60].025 [0.64] Typ..370 [9.40].130 [3.3] Dia. Holes.250 [6.35] Dia. C Bore.080 [2.03] Deep.150 [3.81] E.200 [5.08] Closed Position.250 [6.35].050 [1.27].018 [0.46] Typ. 74 No. of Dimensions Part Numbers Dual Open Open Closed Positions B C D E* One End1 Both Ends1 Both Ends *Metric equivalents in millimeters for post lengths E are = [3.18];.160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. 2Connectors without cam rod and boardlock. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics.

75 Rotary Cam ZIF Connectors, x.200 [2.54 x 5.08] Centerline (Continued) Right-ngle Connector, Solder Post Terminals Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold per MIL-G in contact area; [ ] tin-lead per MIL-P on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Board Lock Feature On connectors open one end and open both ends Daughter PC Board [ ] thick Performance Specifications page 73 Dust Cover page 79 PC Board Hole Layout and Edge Patterns pages 81, 82 Special pplication page 82, [11.18] Closed End B.370 [9.40].130 [3.3] Dia. Holes.250 [6.35] Dia. C Bore.080 [2.03] Deep Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [27.81] Ref..850 [21.60].150 [3.81] Closed Position.250 [6.35].160 [4.06].050 [1.27].210 [5.33] D C [2.54] Typ..025 [0.64] Typ..025 [0.64] Typ..200 [5.08] [2.54] Bend Right Shown No. of Dimensions Dual Bend Part Numbers Positions B C D Right (Open End1) Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. Open both ends. R R L R

76 Rotary Cam ZIF Connectors, x.200 [2.54 x 5.08] Centerline (Continued) Vertical Connector, Wrap-Type Post Terminals Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold per MIL-G in contact area; [ ] tin-lead per MIL-P on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Board Lock Feature On connectors open one end and open both ends Daughter PC Board [ ] thick Performance Specifications page 73 Dust Cover page 79 PC Board Hole Layout and Edge Patterns pages 81, 82 Special pplication pages 82, [11.18] B Closed End.370 [9.40].130 [3.3] Dia. Holes.250 [6.35] Dia. C Bore.080 [2.03] Deep.150 [3.81] Closed Position Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [27.81] Ref..850 [21.60].250 [6.35].050 [1.27].210 [5.33].025 [0.64] Typ. [2.54] Typ. E.025 [0.64] Typ. D.200 [5.08] C No. of Dimensions Part Numbers Dual Open Open Positions B C D E* One End1 Both Ends *Metric equivalents in millimeters for post lengths E are = [14.73] (3-high wrap-type); = [9.65] (2-high wrap-type). 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 76

77 Rotary Cam ZIF Connectors, x.250 [3.18 x 6.35] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold per MIL-G in contact area; [ ] tin-lead per MIL-P on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Board Lock Feature On connectors open one end and open both ends Daughter PC Board [ ] thick Performance Specifications page 73 Dust Cover page 79 PC Board Hole Layout and Edge Patterns pages 81, 82 Special pplication pages 82, [11.18] Closed End B.130 [3.3] Dia. Holes.250 [6.35] Dia. C Bore.080 [2.03] Deep.370 [9.40] Technical Documents: (pages 186,187): Product Specification Instruction Sheet [27.81] Ref..150 [3.81] Closed Position.250 [6.35].850 [21.60].050 [1.27].210 [5.33] D C [3.18] Typ..025 [0.64] Typ. E.250 [6.35].018 [0.46] Typ. No. of Dimensions Part Numbers Dual Open Open Positions B C D E* One End1 Both Ends *Metric equivalents in millimeters for post lengths E are = [3.18]; = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 77

78 Rotary Cam ZIF Connectors,.156 x.200 [3.96 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing Glass-filled polyester, 94V-0 rated Contacts Phosphor bronze, plated [ ] gold per MIL-G in contact area; [ ] tin-lead per MIL-P on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Board Lock Feature On connectors open one end and open both ends Daughter PC Board [ ] thick Performance Specifications page 73 Dust Cover page 79 PC Board Hole Layout and Edge Patterns pages 81, 82 Special pplication pages 82, 96 Technical Documents: (pages 186, 187): Product Specification Instruction Sheet [11.18] [27.81] Ref. Closed End B.850 [21.60].130 [3.3] Dia. Holes.250 [6.35] Dia. C Bore.080 [2.03] Deep.370 [9.40].150 [3.81] Closed Position.250 [6.35].050 [1.27].210 [5.33] D C.156 [3.96] Typ..025 [0.64] Typ. E.200 [5.08].018 [0.46] Typ. 78 No. of Dimensions Part Numbers Dual Open Open Closed Positions B C D E* One End1 Both Ends1 Both Ends *Metric equivalents in millimeters for post lengths E are = [3.18]; = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics

79 ccessories Dust Covers Material: Rigid vinyl, black Dimension Part Numbers Note: Other lengths can be made available upon request, consult Tyco Electronics. Cam Rods with Boot.348 [8.84] Material: Cam Rod Stainless steel Boot Glass-filled polyester, yellow.835 [21.21].654 [16.61] [5.08] [5.08].400 [10.16] Dimension Part Numbers Dimension Part Numbers Note: Other lengths can be made available upon request, consult Tyco Electronics. 79

80 ccessories (Continued) Cam Rods without Boot [3.18] Material: Stainless steel.775 [19.69].055 [1.40].200 [5.08].045 [1.14] Dimension Part Numbers Dimension Part Numbers Note: Other lengths can be made available upon request, consult Tyco Electronics. [3.18].252 [6.40].055 [1.40].260 [6.60].045 [1.14] 80 Dimension Part Numbers Note: Other lengths can be made available upon request, consult Tyco Electronics.

81 Recommended PC Board Hole Layouts Mother Board Hole Layout, Vertical Through-Board Connectors.128 [3.25] Dia. (2 Plc.).048 Dia. Typ. [1.22] W CL X * *Refer to individual connector specifications. B* CL W X Mother Board Hole Layout, Right-ngle Through-Board Connectors.200 [5.08] [2.54] Typ. Pin No. 1 (Ref.).048 [1.22] Dia. Typ..400 [10.16] Max. * PCBoard Edge *Refer to individual connector specifications. 81

82 Recommended PC Board Edge Pattern Daughter Board Edge Pattern.700 [17.78] Min..270 [6.86] Min. CL Minus.006 [0.15] CL B ±.005 [±0.13] C [+0.13] No. of CL = [2.54] CL = [3.18] CL =.156 [3.96] Dual C =.050 [1.27] C =.078 [1.98] C =.094 [2.39] Positions B B B Special pplication Tandem pplication Special Rod (Part No. Series ) llows Customer Supplied Nut Driver ctuation (Refer to page 80.) 82 Note: Contact Tyco Electronics for information concerning special tandem connectors.

83 Linear ZIF Connectors Product Facts Minimizes force needed to install and remove printed circuit boards vailable in lever and bell crank styles Lever styles allow side and top card entry Wiping action contacts enhance electrical properties Contacts on x [2.54 x 2.54] or x [3.18 x 3.18] centers.025 [0.64] square posts ccepts PC boards from.054 to.070 [1.37 to 1.78] in thickness Normally closed design leaves springs in relaxed position 50 to 175 dual positions available on [2.54] centerline connectors and 40 to 140 dual positions available on [3.18] centerline connectors Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30 C Operating Temperature: 65 C to +85 C Contact Resistance: 16 milliohms max. Durability: Tested to 250 cycles (board-to-contact actuation) *Consult Tyco Electronicsengineering when paralleling contacts for power applications. MP Linear Zero Insertion Force (ZIF) PC Board Edge Connectors are available in both lever and bell crank actuated styles and can be provided as panel assemblies, separate housings and contacts or as preassembled with solder post terminals. Panel assemblies include a housing with CTION PIN press-fit solderless contacts mounted on an epoxy board for rack application. Separate housing assemblies and CTION PIN contacts allow customer assembly. These can be mounted as close as.625 [15.88]. More design latitude for high density application is provided by the side entry lever-type connector, permitting use of all sides of the PC board for edge-type I/O connections (see page 133). Where solder applications are required, Tyco Electronics has a line of preassembled connectors with tin-plated solder terminals. ll these configurations are available in a broad range of sizes. With ZIF style connectors, intermittencies can occur if a contact comes to rest on a piece of foreign matter (dust and dirt particles) found on PC boards. To decrease the probability of this happening, all connectors have been designed to include a wiping contact which produces a wiping action. This action, produced by the geometry and bending movements of the beam, pushes aside debris and allows for good electrical connection by cleaning the actual point of contact. In addition, all connectors have removable wings which make it possible to repair or replace damaged cam rails, handles, contacts and housing modules without removing the entire housing assembly from the board. 83

84 Linear ZIF Connectors, x [2.54 x 2.54] Centerline Housing with Solder Posts Lever Style, Side Entry Material and Finish: Housing Glass-filled polyester, black Contacts Copper alloy 725, plated [ ] min. gold per MIL-G in contact area; [ ] min. tin-lead on post with entire contact underplated [ ] min. nickel per QQ-N-290 Related Product Data: Daughter PC Board [ ] thick Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 88 Special pplication page 96 Technical Documents: (pages 186, 187): Product Specification pplication Specification Instruction Sheets , , [11.43].355 [9.02]* Closed C L Last Contact Position B C L First Contact Position.500 [12.70] Max..600 [15.24].845 [21.46] C Open Open End P Closed End.103 [2.62] [2.54].190 [4.83] Mounting Hole CL [27.31] [2.54] Typ..206 [5.23] P.175 [4.45] Mounting Hole CL.845 [21.46] Section P-P 84 *Card slot depth. No. of Dimensions Part Dual Positions B C Number Note: Other connector sizes can be made available, consult Tyco Electronics

85 Linear ZIF Connectors, x [2.54 x 2.54] Centerline (Continued) Panel ssembly Lever Style, Side Entry Material and Finish: Housing Glass-filled polyester, black Contacts Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Daughter PC Board [ ] thick Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 88 CTION PIN Contacts pages 88, 94 Tooling page 95 Special pplication page 96 PC Board Channel C.343 [8.71] Max. Open End.355 [9.02] Card Slot Depth Closed End Technical Documents: (pages 186, 187): [39.50] Product Specification pplication Specification Instruction Sheets , , [3.18].150 [3.81] Countersunk Hole (2 Plcs.) [36.16] [2.54] Typ. [2.54] D.812 [20.62].750 [19.05] B No. of Dimensions Part Dual Positions B C D Numbers Note: Other connector sizes can be made available, consult Tyco Electronics

86 Linear ZIF Connectors, x [2.54 x 2.54] Centerline (Continued) Panel ssembly Lever Style, Top Entry Material and Finish: Housing Glass-filled polyester, black Contacts Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Daughter PC Board [ ] thick Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 88 CTION PIN Contacts pages 88, 94 Tooling page 95 Technical Documents: (pages 186, 187): Product Specifications , pplication Specification Instruction Sheets , , PC Board Channel C [3.18].150 [3.81] Countersunk Hole (2 Plcs.) [36.16].343 [8.71] Max. [2.54] Typ. Closed End.355 [9.02] Card Slot Depth [2.54].615 [15.62] Closed End.812 [20.62] [39.50].750 [19.05] B 86 No. of Dimensions Part Dual Positions B C Numbers Note: Other connector sizes can be made available, consult Tyco Electronics

87 Linear ZIF Connectors, x [2.54 x 2.54] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board [ ] thick Mounting Screws Customer supplies, must be applied before opening connector Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 88 CTION PIN Contacts pages 88, 94 Tooling page 95 Special pplication page 96 Ref. Technical Documents: (pages 186, 187): Product Specifications , pplication Specification Instruction Sheets , , C Open Closed C L Last Contact Position Open End B C L First Contact Position Closed End P.450 [11.43] P.355 [9.02]* Mounting Hole CL.206 [5.23].815 [20.70].600 [15.24] *Card slot depth. Section P-P No. of Dimensions Part Dual Positions B C Numbers Note: Other connector sizes can be made available, consult Tyco Electronics. 87

88 Linear ZIF Connectors, x [2.54 x 2.54] Centerline (Continued) CTION PIN Contacts with Wiping Feature, [2.54] Centerline Recommended PC Board Hole Layout and Edge Pattern, [2.54] Centerline Material and Finish: Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Performance Specifications page 83 CTION PIN Contact Description and pplication Specification page 94 Tooling page 95 Mother Board Hole Layout.120 [3.05] Dia..047 Dia. Typ. [1.19] (Solder Post Only)* Technical Documents: (pages 186, 187): Instruction Sheet B *For CTION PIN post hole diameter, see page 94. C L C (Comb) Connector Dimensions Style C L B C Lever [1.14] Contact rea Prenotched for Breakoff at ssembly Daughter Board Edge Pattern [37.72].745 [18.92] [15.24] Ref. [5.08] Min. B Min..740 [18.80] Post rea Prenotched for Breakoff at ssembly Max. [2.54].098 [2.49] Typ..070 [1.78] (No. of Pos. 1) [2.54 (No. of Pos. 1) +4.98] [2.54].025 [0.64] Sq. Contact Combs Number of Contacts Per Comb* 55 Dimension *t least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Part Number Connector Entry Dimensions Style Style B Side Lever Top Reeled Contacts Number of Contacts Part Per Reel Number 35, Note: Other plating combinations and thicknesses can be made available, consult Tyco Electronics. 88

89 Linear ZIF Connectors, x [3.18 x 3.18] Centerline Panel ssembly Lever Style, Side Entry Material and Finish: Housing Glass-filled polyester, black Contacts Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Daughter PC Board [ ] thick Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 93 CTION PIN Contacts pages 93, 94 Tooling page 95 Special pplication page 96 Technical Documents: (pages 186, 187): Instruction Sheets , , PC Board Channel C.343 [8.71] Max. Open End.355 [9.02] Card Slot Depth.615 [15.62] Closed End [39.50] [3.18].150 [3.81] Countersunk Hole (2 Plcs.) [36.16] [3.18] Typ. [3.18].812 [20.62].750 [19.05] B No. of Dimensions Part Dual Positions B C Numbers Note: Other connector sizes can be made available, consult Tyco Electronics

90 Linear ZIF Connectors, x [3.18 x 3.18] Centerline (Continued) Panel ssembly Bell Crank Style, Top Entry Material and Finish: Housing Glass-filled polyester, black Contacts Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Daughter PC Board [ ] thick Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 93 CTION PIN Contacts pages 93, 94 Tooling page 95 Technical Documents: (pages 186, 187): Instruction Sheets , , [91.95] Ref. (Open).935 [23.75] Max..355 [9.02] Card Slot Depth Closed End [39.50] [3.18].615 [15.62] 2.41 [54.38].609 [15.47] [3.18] Typ. [3.18] B.750 [19.05] 90 No. of Dimensions Part Dual Positions B Numbers Note: Other connector sizes can be made available, consult Tyco Electronics

91 Linear ZIF Connectors, x [3.18 x 3.18] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board [ ] thick Mounting Screws Customer supplied, must be applied before opening connector Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 93 CTION PIN Contacts pages 93, 94 Tooling page 95 Special pplication page 96 Technical Documents: (pages 186, 187): Instruction Sheets , , [12.07] Ref..355 [9.02]* B.815 [20.7].600 [15.24] C Open Closed CL First Contact Position Open End Last Contact Position C L Closed End P.115 [2.92] Section P-P [27.61] P *Card slot depth. Mounting Hole C L.218 [5.54] Mounting Hole C L No. of Dimensions Part Dual Positions B C Number Note: Other connector sizes can be made available, consult Tyco Electronics

92 Linear ZIF Connectors, x [3.18 x 3.18] Centerline (Continued) Housing Bell Crank Style, Top Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board [ ] thick Mounting Screws Customer supplied, must be applied before opening connector Performance Specifications page 83 PC Board Hole Layout and Edge Pattern page 93 CTION PIN Contacts pages 93, 94 Tooling page 95 Technical Documents: (pages 186, 187): Instruction Sheets , , [9.02]*.475 [12.07] [26.97] (Open) [47.60] CL First Contact Position Ref. B Last Contact Position C L.312 [7.92].500 [12.70].815 [20.7].600 [15.24] [65.07] (Closed) [46.23].115 [2.92] P Closed End.115 [2.92] Mounting Hole C L [31.75] P Mounting Hole C L.187 [4.75] Section P-P *Card slot depth. No. of Dimensions Part Dual Positions B Numbers Note: Other connector sizes can be made available, consult Tyco Electronics

93 Linear ZIF Connectors, x [3.18 x 3.18] Centerline (Continued) CTION PIN Contacts with Wiping Feature, [3.18] Centerline Recommended PC Board Hole Layout and Edge Pattern, [3.18] Centerline Material and Finish: Copper alloy 725, plated [ ] gold per MIL-G in contact area; [ ] min. gold flash per MIL-G on post with entire contact underplated [ ] nickel per QQ-N-290 Related Product Data: Performance Specifications page 83 CTION PIN Contact Description and pplication Specification page 94 Tooling page 95 Mother Board Hole Layout.120 [3.05] Dia..047 Dia. Typ. [1.19] (Solder Post Only)* Technical Documents: (pages 186, 187): Instruction Sheet B *For CTION PIN post hole diameter, see page 94. C L C (Comb).045 [1.14] Contact rea Connector Dimensions Style CL B C Lever Bell-Crank Prenotched for Breakoff at ssembly [37.85].750 [19.05].600 [15.24] Ref. Daughter Board Edge Pattern.740 [18.80] Post rea [3.18].025 [0.64] Sq. B Min. Max. [3.18].110 [2.79] Typ..200 [5.08] Min..090 [1.78] Typ. (No. of Pos. 1) [3.18 (No. of Pos. 1) +5.59] Contact Combs Number of Contacts Per Comb* 56 Dimension *t least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Part Number Connector Entry Dimensions Style Style B Side Lever Top Bell-Crank Top

94 Linear ZIF Connectors (Continued) MP CTION PIN Press-Fit Contacts CTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. lso, radial and axial distortion are controlled to meet today s standards for multilayer board applications. PC Board Thickness CTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain CTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ nnular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole 94 CTION PIN Contact/PC Board pplications Connector Type Linear ZIF CTION PIN Contact Material Thickness *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus.020 [0.51]. Drilled Hole Plating Thicknesses Plated Radial Hole Distortion Diameter➁ Through-Hole Copper➂* Tin-Lead➃ Diameter➄ verage Maximum ± ± Min Not Not Specified Specified

95 Linear ZIF Connectors (Continued) Tooling ssembly tooling is not required except when using connectors with CTION PIN contacts. CTION PIN contact assembly requires an arbor-style bench tool with a capacity of 40 lb [178 N] per contact, a support fixture, contact applicator, carrier removal tool and housing assembly tool. Typical procedure is to place a PC board on the support fixture, insert contact combs into the printed circuit board with the contact applicator and seat with the arbor tool. Next, remove the carrier strip from the contact combs with the carrier break-off tool. Place the housing over the contacts with the housing assembly tool, and repeat the entire process until the board is complete. x [2.54 x 2.54] Centerline Connectors No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools Dual Removal ssembly Removal Replacement Insertion Positions pplicator Tool Tool Tool Tool Tool With Housing Without Housing x [3.18 x 3.18] Centerline Connectors No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools Dual Removal ssembly Removal Replacement Insertion Positions pplicator Tool Tool Tool Tool Tool With Housing Without Housing

96 Linear ZIF Connectors (Continued) Special pplication Use Linear and Rotary ZIF Connectors as Card Guides to access more sides of the Daughter Board. Standard Edge II (pages 15 thru 27) or MP PCE Connectors (pages 98 thru 115) 96