Reverse Camera Installation Instructions

Transcription

1 Reverse Camera Installation Instructions XUV500 Issue: 1-01/03/2013 Page 1 of 12

2 Fitting Time: 45 Minutes Parts Supplied: Reverse Camera Wiring Harness Tools and Materials Flat Blade Screw driver Phillips head screw driver Power Drill Cable Ties XUV500 Flashing Tool Issue: 1-01/03/2013 Page 2 of 12

3 Step 1: Remove the following panels Always refer to vehicle workshop manual when removing vehicle components Left side kick trim: Remove plastic nut at front, remove Phillips head screw behind oval cover place. Remove front and rear scuff trims. Remove Screw Issue: 1-01/03/2013 Page 3 of 12

4 Step 2: Remove the following panels Always refer to vehicle workshop manual when removing vehicle components Left side tail light assembly: Pull back boot pinch mould, Remove black cover above tail light and Remove tail light. Pull out wiring rubber boot behind tail light. Remove Tail light bolts Remove Screws Wiring boot removed Issue: 1-01/03/2013 Page 4 of 12

5 Step 3: Remove the following panels Tailgate trim cover: Remove top and side panels by hand. Undo screws and remove pocket along bottom of main trim then remove tailgate trim, taking care to unplug interior light. Issue: 1-01/03/2013 Page 5 of 12

6 Step 4: Fitting Overview Looking at wiring kit, the short section with Male/Female plugs gets inserted behind tail light. The section with the cylindrical plug runs into the tailgate for the camera. The long section with single square plug runs into LHS kick as video input for dash display Issue: 1-01/03/2013 Page 6 of 12

7 Gain Access to the inside of the cargo area, remove hidden screw behind cover, and the manual fuel flap opener override. You will now be able to unclip the top of the panel and lever it out enough to work behind XUV500 Wiring the kit in From inside the car, pass the tailgate T harness out behind the LHS tail light. Make a small cut In the wiring body grommet, then feed the cable through. Reseat the grommet correctly into the body. Then plug the harness in line with the existing vehicle harness and the tail light. Refit tail light and top trim piece Issue: 1-01/03/2013 Page 7 of 12

8 Camera Mounting. Remove numberplate light housing, by undoing 2 x 10mm bolts from inside the tailgate, then unclipping the housing from outside the vehicle Remove switch from light housing Remove passenger Side screw, then Refit screw with camera Attached to assembly Run camera cable back under metal bracket, run camera cable adjacent to switch wiring. Place a small cut in rubber grommet to allow camera lead to pass through. Fit Surround to vehicle as a reverse of removal. Issue: 1-01/03/2013 Page 8 of 12

9 Wiring the Camera Run Camera lead up towards the tailgate behind interior trims. Remove LHS wiring conduit, run cable through. Use lubricant to assist pulling through if needed Reseat grommets for wiring conduit. Run camera lead to camera cable, securing with cable ties. Plug cable end together, tape connection and secure with ties. Reassemble tailgate. Issue: 1-01/03/2013 Page 9 of 12

10 Wiring to the front of vehicle Run the remaining lead behind the LHS cargo bay trim, being sure to locate it low behind the trim to avoid fouling on mounting clips upon reassembly. Run lead behind pinchmould on wheel-arch and under rear and front scuff trims. Secure the cable so it avoids mounting clips on reassembly. Using a screw driver, push the lead under the bottom of the B pillar trim. Plug lead into video access plug in kick panel, tape connection and cable tie off. Test system and reassemble vehicle in full. Issue: 1-01/03/2013 Page 10 of 12

11 Step 5: Reverse Camera Activation To activate the camera in the vehicle, enable the RVC in IS (Infotainment System) using XUV500 flashing tool as mentioned below: 1. Connect XUV500 flashing tool and select IS (Infotainment system) 2. Select CONFIG 3. In Feature Selection, select Rear View Camera and click Enable 4. Switch OFF the ignition, wait for 20 seconds and switch ON ignition Issue: 1-01/03/2013 Page 11 of 12

12 Step 6: Final test and image alignment With the engine running and the handbrake engaged, place the vehicle into reverse. The reverse image should look similar to the below image. Some slight adjustment to the camera may be necessary by loosening the camera in its housing adjusting to the correct angle and re-tightening. Please note this reverse camera option activates in reverse only and is not accessible via the Car Info / Reverse Camera Sub menu from the vehicles main screen. This feature is inactive and will yield a black screen unless the vehicle is in reverse. Photo of reverse image on screen Once the desired image is achieved, perform a physical reversing test Issue: 1-01/03/2013 page 12 of 12.