Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # )

Size: px
Start display at page:

Download "Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # )"

Transcription

1 Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # ) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts Program Module 22--pin white connector w/ video T15 & T20 Torx Bits 7mm & 10mm Sockets Phillips Screwdriver Plastic Trim Removal Tool Soldering Iron, Solder, & Heat Shrink Tubing (RECOMMENDED) or T-taps as an alternate splicing method Electrical Tape These instructions Please read so you do not VOID the warranty: If the camera harness is ran though the center on the camera bracket, it will cut the camera harness. This will VOID the warranty on the camera. Safety Precautions: Work in a well-ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions.

2 Install Camera: Wheel Alignment for Camera Clearance Step 1: Loosen lug nuts to remove spare tire. Step 2: Slide Camera on studs placing harness end on top of tire carrier. Do not run harness through the camera bracket opening. Step 3: Temporarily replace spare tire to check wheel clearance to Camera. Step 4: Remove spare tire and slide (3) supplied Push Nuts on the studs.

3 Install Chassis Harness: Step 5: Plug the Camera connector into the gray Chassis Harness connector, and insert RCA connector end of supplied Chassis Harness through the rear gate vent behind tire carrier. Step 8: Use supplied Wire Ties to secure Chassis Harness to existing harness. Step 9: Use supplied Wire Ties to secure Chassis Harness to fabric factory wire cover. CAUTION: Leave enough slack to allow gate to open fully. Step 6: Using a plastic trim removal tool, remove interior panels on inside of rear gate. Step 10: Use a T20 Torx bit to remove subwoofer box. Step 11: Using a plastic trim removal tool, pry off rear seat belt closeout. Step 7: Pull harness through the rear gate openings.

4 Step 12: Using a plastic trim removal tool, remove rear access panel to expose 10mm bolt, and remove bolt. Step 16: Use a 10mm socket to remove the existing nut located behind the passenger kick panel and attach ground eyelet of Chassis Harness to chassis ground. Step 13: Pull out subwoofer box slightly to gain access to run Chassis Harness along existing harness. Step 14: Pull back carpet and continue running Chassis Harness forward. Step 18: Remove rubber bin insert from top of dash. Step 15: Run Chassis Harness under B-pillar cover to passenger door sill. Use a plastic trim removal tool to remove the (2) plastic push pins and remove passenger sill plate/kick panel. Step 19: Remove 7mm bolt.

5 Step 20: Using a plastic trim removal tool, remove window switch panel. Step 21: Disconnect harness from window switches. Step 23: Remove driver knee bolster cover. Step 24: Remove (2) 7mm bolts on both sides of the steering column. Step 25: Remove center stack/cluster surround. Step 26: Remove glove box for access and run Chassis Harness toward center of dash. Step 22: Remove 7mm bolt.

6 Step 27: Using a plastic trim removal tool, remove HVAC panel. Step 31: Plug in the 22 pin white connector to the open connector on the back of the radio. Step 28: Run Red 12v+ ignition power wire and green trigger wire of supplied Chassis Harness to ignition controlled power point on HVAC panel power point. Step 32: Connect White 22-pin Connector to radio along with all remaining radio connectors before reinstalling radio head unit and all trim removed. Step 29: Splice Red power wire and the green trigger wire from the chassis harness to Blue/Red wire on back of power point. RECOMMENDED: Use solder and cover with heat shrink tubing or use T-taps as an alternate connection method. Step 33: Connect male RCA of camera into female RCA of jumper harness and proceed to the Programming Instructions. Step 30: Plug the Chassis Harness RCA connector into your aftermarket display.

7 Programing Instructions PLEASE NOTE: These modules are VIN locked for single use. a) With the module not plugged in, key on the ignition and wait 10 seconds for the chimes and lights to stop flashing. b) Plug module into OBDII port, located under the dash on the driver s side, and wait to hear honk honk. Programming is completed. c) Unplug the module from the OBDII port. Step 35: Test the system. Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your aftermarket display. Step 36: Reassemble vehicle. Follow your disassembly steps in reverse order, taking care not to bind the harness wiring when reinstalling trim.

8 Factory Display Camera Harness for Chrysler Town & Country, Dodge Durango, Grand Caravan, & Ram Tradesman, Jeep Commander, Grand Cherokee and Wrangler Factory Displays (Kit part number ) NOTE: Requires Chrysler/Dodge dealer to activate; see below Applications: 2011 current Chrysler Town & Country (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Durango (RHR, RHB, RHZ, RHP radios) 2011 current Dodge Grand Caravan (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Ram Tradesman (RBZ, RHB, RER, REZ, RBZ, REW radios) Jeep Commander (430, 730 radios) 2008 current Jeep Grand Cherokee (430, 730, RHR, RHB, RB2, RHP radios) 2007 current Jeep Wrangler (display radios) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Factory Display RCA Jumper Harness Loose red and black wires (if needed) White 22-pin Connector These Instructions Tools & Supplies Needed: Delphi Terminal Removal Tool # or Small Flat Watch Repair Screwdriver 10mm Socket Plastic Trim Removal Tool Vehicle Service Manual (If needed) Safety Precautions: Work in well ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions. IMPORTANT: Use of this camera with the factory display requires activation by a Chrysler/Dodge dealer. See below for Dealer Programming Instructions. If possible, have the dealer enable the camera option prior to installation.

9 Step 1: Use a Plastic Trim Removal Tool to remove console and dash trim pieces to gain access to the radio bezel. Step 2: Use a Plastic Trim Removal Tool to remove radio bezel. Step 3: Unplug all radio connectors from the radio head unit and set radio aside. Only complete Step 4 and 5 for Dodge Durango, Jeep Grand Cherokee, RAM Truck vehicles with 52-pin radio connectors. Step 4: Insert terminal from red wire on supplied jumper harness into position 31 of black 52-pin radio connector and insert terminal from black wire on supplied chassis harness into position 32 of black 52-pin radio connector. Continue with steps 6 through 9 for vehicles with 22-pin radio connector. IMPORTANT: If the White 22-pin connector is present in the vehicle and Pin 3 and/or Pin 4 are already populated, remove the terminal(s) using Delphi Terminal Removal Tool # or a Small Flat Watch Repair Screwdriver and isolate with Electrical Tape. Step 6: Remove both terminals from chassis harness. Splice provided loose red wire to chassis harness red wire and insert terminal into pin position 3 on the white 22-pin radio connector (Figure 1) until it clicks securely. Figure 1 Step 5: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included). Step 7: Splice provided loose black wire to chassis harness black wire and insert terminal into pin position 4 on the white 22-pin radio connector (Figure 1) until it clicks securely. Step 8: Connect White 22-pin Connector to radio along with all remaining radio connectors before reinstalling radio head unit and all trim removed. Step 9: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included).

10 Dealer Programming Instructions PARK VIEW REAR BACK-UP CAMERA VEHICLE CONFIGURATION Vehicle VIN must be updated with the sales code of the added accessory in order to enable system functionality. Using the DealerCONNECT and the scan tool, complete the procedure below: A. In the Vehicle Option screen under Global Claims System category in the Service tab, enter the VIN and add the following sales code: XAC (PARK VIEW REAR BACK-UP CAMERA) as a Dealer Installed Option. B. Confirm that the new sales code has been successfully added to the VIN. With the scan tool connected to both the internet (via Ethernet port or wireless connection) and the vehicle, perform the following steps: C. Using the scan tool, select VEHICLE PREPARATION and then select RESTORE VEHICLE CONFIGURATION. D. Follow the step by step instructions on the scan tool to complete the Park View Rear Back-Up Camera vehicle configuration. Step 23: Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your factory display. If you re looking for quality cameras & driver safety products by Brandmotion, we ve you covered.

INSTALLATION INSTRUCTIONS. Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # )

INSTALLATION INSTRUCTIONS. Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # ) Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # 9002-8847) Items Included in the Kit Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA

More information

Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # )

Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # ) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions 22--pin white connector w/ video RCA (for factory display radio) Jeep Wrangler Rear Vision

More information

Jeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # )

Jeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # ) Items Included in the Kit Jeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # 9002-8848) Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA (for factory display radio)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies

More information

Jeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # )

Jeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # ) Jeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # 9002-8857) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Power

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 9002-6513 Rear Vision System W/ Zoom Aftermarket and Factory 8.4 Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 2012 RAM (Part B) 2013 Current RAM (Part A) NOTE:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Aftermarket display (Kit # AVMS-3700v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Factory Display Radios (Kit # AVMS-3701) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2007-Current Jeep Wrangler 360º System for Factory MyGig Display (Kit # AVMS-3701) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2015 Silverado Qi Wireless Charging Kit (Kit # FDMC-1276) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless Charging Module

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Recessed Lip Camera with Harness and Auto Dimming Mirror (Kit part number 9002-8721) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Recessed Lip Camera with Harness and Slimline Mirror (Kit part number 9002-8724) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2015 - Ford Mustang Qi Wireless Charging Kit (Kit # FDMC-1222) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless Charging

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2015 Tahoe/Suburban/Yukon Qi Wireless Charging Kit (Kit # FDMC-1273) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Dual Camera Blind Spot Monitoring System w/multi-camera Switcher (Kit # 9002-2904) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Ford 4 MyFord factory display interface for backup camera (Kit # 9002-2750v2) Please read thoroughly before starting installation and check that kit contents are complete. ***SEE PAGES 5-6 TO DETERMINE

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Toyota 24-pin Dual Camera Blind Spot Monitoring System (Kit # 9002-2911) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 2 Adjustable

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Toyota 24-pin Dual Camera Blind Spot Monitoring System (Kit # 9002-2911) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 2 Adjustable

More information

OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number )

OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number ) OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8723) Items Included in the Kit: Bubble bag containing: Camera with Mount Mirror Mirror

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Recessed Lip Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS OEM Tailgate Camera/Bezel Assembly with Chassis Harness 2014-current Chevrolet Silverado and GMC Sierra (Kit part number 9002-1005) Kit Contents: Chassis Harness 1 bubble bag containing: Tailgate Handle

More information

Rear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )

Rear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number ) Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some

More information

Please read thoroughly before starting installation and check that kit contents are complete.

Please read thoroughly before starting installation and check that kit contents are complete. Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear

More information

Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number )

Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number ) Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)

More information

Please read thoroughly before starting installation and check that kit contents are complete.

Please read thoroughly before starting installation and check that kit contents are complete. Radar Blind Spot Brackets for 2015-Current Toyota RAV4 (Part # RDBS-1411) ***REQUIRES RDBS-1400 UNIVERSAL RADAR BLIND SPOT SYSTEM*** Please read thoroughly before starting installation and check that kit

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2012-2014 F-150 4 MyFord factory display 360º Vision System (Kit # AVMS-3604) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Video

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Qi Wireless Charging Installer Kit (Kit # FDMC-1210) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi

More information

or Chrysler Multikit 2007-up* TABLE OF CONTENTS See page 2 KIT FEATURES

or Chrysler Multikit 2007-up* TABLE OF CONTENTS See page 2 KIT FEATURES 95-6511 or 99-6511 INSTALLATION INSTRUCTIONS 95-6511 ISO DDIN radio provision Textured 99-6511 DIN radio provision with pocket ISO DIN radio provision with pocket KIT COMPONENTS 95-6511 A) Long nose (wide)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System NAV Display 2009-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9501) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness NAV Harness 1

More information

Chrysler Multi-kit TABLE OF CONTENTS Dash Disassembly...2 Kit Assembly

Chrysler Multi-kit TABLE OF CONTENTS Dash Disassembly...2 Kit Assembly 99-650345 INSTALLATION INSTRUCTIONS Chrysler Multi-kit 1998-2010 INTRODUCTION This instruction booklet will cover (3) different kits, yet carry the same applications and dash disassembly. After dash disassembly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA

More information

INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chrysler Multi Kit. A) Radio Housing B) ISO Trim Plate C) ISO Snap in Brackets

INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Chrysler Multi Kit. A) Radio Housing B) ISO Trim Plate C) ISO Snap in Brackets INSTALLATION INSTRUCTIONS FOR PART 99-60 APPLICATIONS Chrysler Multi Kit 99-60 KIT FEATURES DIN Head Unit Provision with pocket ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing B)

More information

Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)

Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 360º Vision System for Aftermarket Radio/Display (Kit # AVMS-3690) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING Please read

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Multi Camera Interface (Kit # 9002-6118) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Interface module Video input harness These

More information

# ) THERE ARE 2 DIFFERENT HEIGHT BRACKETS. MAKE SURE THAT THIS IS THE CORRECT ONE FOR YOUR FAIRLEAD!

# ) THERE ARE 2 DIFFERENT HEIGHT BRACKETS. MAKE SURE THAT THIS IS THE CORRECT ONE FOR YOUR FAIRLEAD! SummitView Winch Mount Front Camera (SHORT) (Kit # 9002-8850) THERE ARE 2 DIFFERENT HEIGHT BRACKETS. MAKE SURE THAT THIS IS THE CORRECT ONE FOR YOUR FAIRLEAD! Please read thoroughly before starting installation

More information

INSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number )

INSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number ) Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number 1009-6503) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA extension may be required to connect to your

More information

Chrysler/Dodge/Jeep (without NAV)

Chrysler/Dodge/Jeep (without NAV) Installation instructions for part 99-6507 Chrysler/Dodge/Jeep (without NAV) 2005-2010 99-6507 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket WIRING & ANTENNA CONNECTIONS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic

More information

AEV30229AD Last Updated: 06/17/14 REAR VISION SYSTEM INSTALLATION GUIDE

AEV30229AD Last Updated: 06/17/14 REAR VISION SYSTEM INSTALLATION GUIDE AEV30229AD Last Updated: 06/17/14 REAR VISION SYSTEM INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Mirror Display 2004 onwards Ford F-150 and 2008 onwards Ford Super Duty (Kit part numbers 1008-9520 and 1008-9525) Kit Contents: RVS Interior (shorter) Harness RVS Chassis (longer) Harness

More information

CONTENTS: TOOLS REQUIRED:

CONTENTS: TOOLS REQUIRED: CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N RBI77KICK37 1EA. POWER HARNESS P/N RH41PMP 1EA. OVERLAY HARNESS P/N RH41PM 3EA. NUT P/N RFM6NUT 6EA. WIRE TIE P/N RFZIP6 1EA. FUSE 30 AMP P/N

More information

INSTALLATION MANUAL

INSTALLATION MANUAL INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Universal Radar Blind Spot System (Part # RDBS-1400) Please read thoroughly before starting installation and check that kit contents are complete. NOTE: VEHICLE-SPECIFIC INSTRUCTIONS ARE INCLUDED WITH

More information

TOYOTA tc HANDS FREE BLU LOGIC Preparation

TOYOTA tc HANDS FREE BLU LOGIC Preparation TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

GM TRUCK BACKUP CAMERA INSTALLATION

GM TRUCK BACKUP CAMERA INSTALLATION GM TRUCK 07-13 BACKUP CAMERA INSTALLATION Thank you for your purchase! These instructions are intended for the do-it-yourselfer who decides to install the camera without professional assistance. Keep in

More information

INSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number )

INSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number ) Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number 1009-6503) Kit Contents: Chassis Harness with RCA Endgate Handle with Camera 1 bag containing: Wire Ties (Qty: 17) Bottle

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness with

More information

Audio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only)

Audio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only) 2005-2006 Dodge Magnum, Chrysler 300C, Dodge Charger 2005-2006 Jeep Commander (Premium Audio Only) 2005-2006 Dodge Ram (Regular Cab, Quad Cab, Mega Cab) 2005-2007 Jeep Grand Cherokee (Premium sound) TOOLS

More information

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools

TOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number

More information

Dodge Ram 09-Current CS-DTR SERIES BACKUP CAMERA INSTALLATION

Dodge Ram 09-Current CS-DTR SERIES BACKUP CAMERA INSTALLATION Dodge Ram 09-Current CS-DTR SERIES BACKUP CAMERA INSTALLATION Thank you for your purchase! These instructions cannot possibly cover every option group for every model year of RAM trucks so you may find

More information

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation

TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Mirror Display Dodge Ram Kit Contents: Instruction Sheets Template Chassis Harness Endgate Handle with Camera Wire Ties (Qty: 17) Bottle of ZTech Plug for Non-Locking Endgates (Optional)

More information

Installation Instructions for 2018 Jeep Grand Cherokee Laredo & Altitude and 2018 Dodge Durango SXT & SXT Plus

Installation Instructions for 2018 Jeep Grand Cherokee Laredo & Altitude and 2018 Dodge Durango SXT & SXT Plus Thank you for purchasing the SmartStopStart module! Please read this important information and keep this document with your vehicle owner's manual. Installation Instructions for 2018 Jeep Grand Cherokee

More information

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation

TOYOTA VENZA HANDS FREE BLU LOGIC Preparation TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

Honda Accord 2013-up B

Honda Accord 2013-up B Installation Instructions for 99-7804B REV. 3/17/2015 INST99-7804B KIT FEATURES ISO DIN radio provision with pocket DDIN radio provision Painted two tone to match factory Retains factory color screen Honda

More information

SP EVO-CHR4 (A)

SP EVO-CHR4 (A) TIP SHEET Installation Tips for SP-502 + EVO-CHR4 (A) Remote Start / Alarm T1630 Chrysler 300 (2008-2011) Dodge Magnum (2008) Chrysler Town and Country (2008-2015) Dodge RAM (2009-2012) Dodge Challenger

More information

INSTALLATION INSTRUCTIONS. Rear Vision System Mirror Display 2010 onwards Camaro (Kit part number )

INSTALLATION INSTRUCTIONS. Rear Vision System Mirror Display 2010 onwards Camaro (Kit part number ) Rear Vision System Mirror Display 2010 onwards Camaro (Kit part number 1018-9540) Kit Contents: RVS Interior (shorter) harness RVS Chassis (longer) harness Camera with mounting bracket Mirror 1 bag containing:

More information

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools

General Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

Jeep JK Wrangler XHD Rear Tire Carrier

Jeep JK Wrangler XHD Rear Tire Carrier Contents: 1. Frame (1) 2. Pivot Mount (1) 3. Latch Mount (1) 4. Lug Nuts (3) 5. Catch Pin (1) 6. M12 Washer (18) 7. M12 x 30 Hex Bolt (14) 8. Brake Light Mount (1) 9. Snap Ring (1) 10. Rub Strip (1) 11.

More information

Jeep Wrangler PSS-20WRA Sound System Installation Manual Model: Wrangler Unlimited Model Year:

Jeep Wrangler PSS-20WRA Sound System Installation Manual Model: Wrangler Unlimited Model Year: UNLIMITED 1/20 Jeep Wrangler PSS-20WRA Sound System Installation Manual Model: Wrangler Unlimited Model Year: 2007 2014 *Not compatible with factory amplified systems Jeep Model Year Wrangler Unlimited

More information

TIP SHEET. Step 1: Prepare the Vehicle

TIP SHEET. Step 1: Prepare the Vehicle TIP SHEET Installation Tips for LC + EVO-CHR4 (C) Remote Start Kit Pre-wired Txxxx Chrysler 300 (2011) Chrysler Town and Country (2011-2015) Dodge RAM (2011-2012) Dodge Challenger (2011-2014) RAM CV (2011-2016)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM

More information

Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up B

Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up B Installation instructions for 99-6518B Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B KIT FEATURES ISO DIN radio provision

More information

Nissan Pathfinder (without NAV) (with color screen) HG

Nissan Pathfinder (without NAV) (with color screen) HG Installation instructions for part 99-7627HG Nissan Pathfinder 2013-2016 (without NAV) (with color screen) 99-7627HG KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted to

More information

SCION TC HANDS FREE BLU LOGIC Preparation

SCION TC HANDS FREE BLU LOGIC Preparation SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Bongiovi Acoustics DPS GM 30-Pin Harness (Kit part number 2000-3802) Applications Covered: 2008 Current Buick Enclave (6 speaker) 2007 Current Chevy Avalanche (6 speaker) 2006

More information

(1) Remote Control with (2) AAA Batteries

(1) Remote Control with (2) AAA Batteries TOOLS REQUIRED: KIT CONTENTS: E14 Torx (1) Remote Control with (2) AAA Batteries (2) Wireless Headphones with (4) AAA Batteries (2) DVD Headrest Units Owner s Manual (1) Owner s Manual (1) Power / Audio

More information

Installation Instructions

Installation Instructions Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket

More information

80703 & Backside License Plate Mount for Jeep JK Wrangler (80707) & 10+ (80703)

80703 & Backside License Plate Mount for Jeep JK Wrangler (80707) & 10+ (80703) 80703 Backside Mount 80707 Backside Mount REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

CONTENTS TOOLS REQUIRED:

CONTENTS TOOLS REQUIRED: CONTENTS 1EA. FIVE CHANNEL AMPLIFIER P/N MPDSP033AA 1EA. AMPLIFIER BRACKET P/N RM11JK41 1EA. POWER HARNESS P/N RH41JKP 1EA. OVERLAY HARNESS P/N RH41JK 1EA. FUSE 30 AMP P/N RFUSE30 6EA. WIRE TIE P/N RFZIP6

More information

INSTALLATION GUIDE AOI0020. aoielectrical.com IMPALA, 2011+CHEVY CAPRICE FORD F FORD EXPLORER

INSTALLATION GUIDE AOI0020. aoielectrical.com IMPALA, 2011+CHEVY CAPRICE FORD F FORD EXPLORER INSTALLATION GUIDE AOI0020 2001-2014 IMPALA, 2011+CHEVY CAPRICE 2007-2013 FORD F150 2007-2013+ FORD EXPLORER 2013+ FORD UTILITY/ SEDAN INTERCEPTOR 2007-2013+ DODGE CHARGER 2007-2013+DURANGO 2008-2013+

More information

Tools Needed: 7mm Socket socket wrench socket extension interior removal tool wire cutter electical tape Wrangler Raxiom Navigation

Tools Needed: 7mm Socket socket wrench socket extension interior removal tool wire cutter electical tape Wrangler Raxiom Navigation 2007-2010 Wrangler Raxiom Navigation Contents: (1) - Raxiom Head Unit (1) - Headphone Jack With Wire (A) (1) - GPS Antennae With Wire (B) (1) - Amplifier Pre-Outs Wire Harness (C) (1) - External Microphone

More information

Jeep Cherokee Latitude/Limited 2014-up

Jeep Cherokee Latitude/Limited 2014-up Installation instructions for part 99-6526 REV. 5/23/2017 INST99-6526 KIT FEATURES ISO DDIN radio provision Included interface shows climate and menu info on the aftermarket radio screen. Painted scratch-resistant

More information

TOOLS REQUIRED: Panel Removal Tool Phillips Screwdriver 10mm Nut Driver Ratchet 10mm Socket 7mm Wrench 7mm Nut Driver Straight Screwdriver

TOOLS REQUIRED: Panel Removal Tool Phillips Screwdriver 10mm Nut Driver Ratchet 10mm Socket 7mm Wrench 7mm Nut Driver Straight Screwdriver CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N MPDSP039AA 1EA. OVERLAY HARNESS P/N RH41LX10 3EA. 7MM SCREWS P/N RF7MM 6EA. WIRE TIE P/N RFZIP6 1EA. 30 AMP FUSE P/N RFUSE30 1EA. INSTRUCTIONS

More information

CJ1278 IN-DASH INSTALLATION KIT FOR SELECT 1974-UP CHRYSLER AND JEEP VEHICLES INTRODUCTION PRELIMINARY PARTS LIST ASSEMBLING THE KIT

CJ1278 IN-DASH INSTALLATION KIT FOR SELECT 1974-UP CHRYSLER AND JEEP VEHICLES INTRODUCTION PRELIMINARY PARTS LIST ASSEMBLING THE KIT INTRODUCTION The Scosche in-dash Installation Kit for 1974-UP Chrysler and Jeep Vehicles provides the parts you need to mount your car stereo/cassette player into your vehicle's dash. Refer to the individual

More information

Installation of Auto Meter Cobalt Boost/Vacuum Gauge:

Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:

More information

Mazda-CAM 2. Reverse camera kit for select Mazda NTV-KIT812 BHM 04/06/17 NTV-DOC294

Mazda-CAM 2. Reverse camera kit for select Mazda NTV-KIT812 BHM 04/06/17 NTV-DOC294 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 Mazda-CAM 2 Reverse camera kit for select Mazda NTV-KIT812 BHM Overview The Mazda-CAM 2 integrates a single reverse camera

More information

Installation Instructions

Installation Instructions Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic

More information

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback) Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting

More information

CONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED:

CONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED: CONTENTS: 1EA. SUBWOOFER ENCLOSURE 1EA. SUBWOOFER HARNESS 2PIECE 2EA. T-TAP 1EA. FUSE 30 AMP 6EA. WIRE TIES 1EA. INSTRUCTIONS P/N 77KICK14SUBASSEMBLY P/N RHPM1 P/N RFTTAPB P/N RFUSE30 P/N RFZIP6 P/N RBI77KICK14

More information

SCION XB HANDS FREE BLU LOGIC Preparation

SCION XB HANDS FREE BLU LOGIC Preparation SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

CAR STEREO CONNECTORS

CAR STEREO CONNECTORS 1996-98 Jeep Grand Cherokee 1. Extract (5) screws from along top of dash instrument bezel. 2. Carefully pop out wood grain trim panel around a/c heater control. 3. Carefully pop out wood grain trim panel

More information

Required Parts and Tools

Required Parts and Tools Welcome to the installation guide for the 2004 to 2009 CLK Class Mercedes Benz. Please thoroughly review this manual before installation as there are details that are essential to operation of the vehicle.

More information

TOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation

TOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured

More information

Backside License Plate Mount for Jeep JK Wrangler

Backside License Plate Mount for Jeep JK Wrangler REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH LEDS PLASTIC PASS-THROUGH GROMMET STAINLESS

More information

SCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools

SCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00090 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item 1 Item 2 Item

More information

Nissan Maxima (with Technology Package) Nissan Maxima (with NAV) 2009 KIT FEATURES. ISO DIN radio provision with pocket...

Nissan Maxima (with Technology Package) Nissan Maxima (with NAV) 2009 KIT FEATURES. ISO DIN radio provision with pocket... 99-7633 INSTALLATION INSTRUCTIONS KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted high gloss black KIT COMPONENTS A) Radio trim panel with climate controls B) Radio brackets

More information

SCION tc ILLUMINATED DOOR SILLS Preparation

SCION tc ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill

More information

INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT

INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT PART NUMBER: 0000-89-N30 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TRAILER HITCH MAIN HARNESS KIT APPLICABLE MODELS: 2016 > CX-9 PACKAGE CONTENTS: INSTALLATION INSTRUCTIONS QTY 1 CABLE TIE MOUNT QTY

More information