ETA. Corolla Verso RHD ELECTRONIC TRAFFIC AVOIDANCE. INSTALLATION INSTRUCTIONS for ETA ANTENNA (*) MAIN KIT ETA PZ445-T ANTENNA KIT

Size: px

Start display at page:

Download "ETA. Corolla Verso RHD ELECTRONIC TRAFFIC AVOIDANCE. INSTALLATION INSTRUCTIONS for ETA ANTENNA (*) MAIN KIT ETA PZ445-T ANTENNA KIT"

Ashley Hampton
6 years ago
Views:

ETA ELECTRONIC TRAFFIC AVOIANCE INSTALLATION INSTRUCTIONS for Corolla Verso REQUIRE PARTS ALREAY PREWIRE ETA ANTENNA (*) NOT PREWIRE MAIN KIT ETA PZ445-T933-00 ANTENNA KIT - PZ445-T928-00 ETA BRACKET

1 ETA ELECTRONIC TRAFFIC AVOIANCE INSTALLATION INSTRUCTIONS for Corolla Verso REQUIRE PARTS ALREAY PREWIRE ETA ANTENNA (*) NOT PREWIRE MAIN KIT ETA PZ445-T ANTENNA KIT - PZ445-T ETA BRACKET - PZ425-E FAKRA CONNECTOR - PZ445-E A-PILLAR CLIPS: / (*) Verify whether the vehicle has a prewired ETA by checking the presence of the ETA-antenna in the proximity of the rear view mirror. FOR **R*R RH Manual Ref. no. AIM

2 ELECTRONIC TRAFFIC AVOIANCE PRES PLEASE REA THOROUGHLY THESE PRES BEFORE THE INSTALLATION Be sure to disconnect the negative (-) lead from the battery terminals. Confirm that lamps, horn, wiper and other car accessories operate normally. o not pinch the rear wiring or harness in the tightened part. Protect your car using wing covers, seat and so on. When passing the wires through the bulkhead or other panels, use a grommet to ensure waterproofing. Protect the wiring using tape when it is passed through a hole. Use the correct tool when tightening bolts or nuts. waterproof - O.K.!! Grommet Taping When disconnecting the connectors, be sure to grip the connector body. o not tug on the wiring. Before drilling a hole, check that the rear of the mounting wall is clear. Stop it! Be sure to firmly tighten connectors and terminals. o not forcibly pull any car wiring harness. Rough tugging may result in opened connections, or a broken wire or harness. Insert completely Before connecting the power wiring to the battery, check the wiring connections, harness, etc. to see that they are properly secured. Check body and trim near area of installation to be certain no dirt or scratches resulted from the installation Corolla Verso (RH) - 2

3 ELECTRONIC TRAFFIC AVOIANCE TABLE OF CONTENTS Precautions... 2 Main Kit ETA... 4 ETA Bracket Kit (only in case of a prewired ETA-antenna)... 4 RS-Antenna Kit... 5 Installation Overview... 6 For vehicles without prewired ETA-antenna Vehicle isassembly... 7 Installation of the RS-Antenna Wire... 0 Installation of the RS-Antenna Strip... 2 Installation of the RS-Tuner... 3 For vehicles with prewired ETA-antenna Installation of the RS-Tuner... 5 (For installation of navigation, please refer to the navigation installation manual AIM ) Corolla Verso (RH)

4 ELECTRONIC TRAFFIC AVOIANCE MAIN KIT ETA PZ445-T No. Part Name Part No. Qty RS-TUNER PZ445-T SUBWIRE HARNESS PZ445-T ETA BRACKET KIT(only in case of a prewired ETA-antenna) PZ425-E c e f No. Part Name Part No. Qty 7 ETA BRACKET c BOLT (M 5X8) 2 e f FOAM TAPE 2 BUTYL TAPE Corolla Verso (RH) - 4

5 ELECTRONIC TRAFFIC AVOIANCE RS-ANTENNA KIT PZ445-T No. Part Name Part No. Qty 6 ANTENNA STRIP PZ445-E RS-ANTENNA WIRE PZ445-T928-0 FAKRA CONNECTOR PZ445-E TAPPING SCREW A-PILLAR CLIPS / No. Part Name Part No. Qty CLIPS FOR A-PILLAR (see p. 8) / Corolla Verso (RH)

6 ELECTRONIC TRAFFIC AVOIANCE INSTALLATION OVERVIEW IMPORTANT: Please verify whether the vehicle has a prewired ETA-antenna or not. In case of a prewired ETA-antenna, the ETA bracket kit is necessary. 6 (**) 9 (*) 6 9 RS-ANTENNA WIRE RS-TUNER (*) In case of a non-prewired RS-tuner (**) In case of a prewired RS-tuner ANTENNA STRIP NAVIGATION ECU Corolla Verso (RH) - 6

7 ELECTRONIC TRAFFIC AVOIANCE VEHICLE ISASSEMBLY For vehicles without prewired ETA-antenna. Remove the front door scuff plate (L). : Hook (9x) Fig Remove the passenger seat : Bolt (5x) 0 : Cover (3x) : Hook 3 x (2x) Fasten the bolts with specified torque wrench (37 Nm) when reassembling Fig. 2 Corolla Verso (RH)

8 ELECTRONIC TRAFFIC AVOIANCE 3. Remove the kick panel (L) 4. : Hook (2x) 02 : Nut (x) 4 02 Fig Remove the left front pillar garnish 5. : Clip (2x) o not reuse the removed clips. Order new clips (part nrs and ). 5 Fig a) Remove the map lamp assembly 8. : Clip (2x) : Bolt (2x) b) isconnect the connector. ON OFF OOR ON OFF OOR Fig Corolla Verso (RH) - 8

9 ELECTRONIC TRAFFIC AVOIANCE Remove the holder 9 of the sun visor 0 by turning it counterclockwise. ON OFF OOR 90 9 Fig Pull the sun visor 0 to the LH side of the vehicle. Fig. 7 Corolla Verso (RH)

10 ELECTRONIC TRAFFIC AVOIANCE INSTALLATION OF THE RS-ANTENNA WIRE For vehicles without prewired ETA-antenna Ground wire. If not yet insulated, do so with the complete ground wire of the RS-antenna wire by wrapping it into tape 2. 2 Fig Before routing the RS-antenna wire, protect the RS-antenna black wired pin and the RS-antenna connector by wrapping it into tape 2. Fig (*) 3. a) Tuck the RS-antenna wire through the space between the roof headliner and windshield. b) Route and attach the RS-antenna wire along the vehicle wire harness 3 using wire ties 5 (3x) (*) and tape 2 (2x) (*). (*) 2 Be sure to attach the RS-antenna wire as far as possible against the border of the roof headliner. (*) Included in the navigation kit. Fig Corolla Verso (RH) - 0

11 ELECTRONIC TRAFFIC AVOIANCE 4. Route and attach the RS-antenna wire down the instrument panel into the left kick panel section of the vehicle. Use 4 wire ties 5 (*). (*) Included in the navigation kit. 5 (*) Fig. 5 (*) a) Route the antenna wire along the front scuff plate area under the carpet (along the cross member 6) to the navigation-ecu location 9. b) Attach the antenna wire to the vehicle wire harness using wire ties 5 (3x) (*). c) Bundle up the excess antenna wire under the carpet. (*) Included in the navigation kit. Excess wire Fig Route and attach the ground wire using a bolt 05 as shown. 05 : Bolt (M6x0) (x) Ground wire 05 Fig. 3 Corolla Verso (RH)

12 ELECTRONIC TRAFFIC AVOIANCE INSTALLATION OF THE RS-ANTENNA STRIP For vehicles without prewired ETA-antenna Centre 70 mm 20 mm Coated area Fig a) Thoroughly clean the mounting surface of the front window to which the antenna strip 6 is to be affixed. b) Remove the release paper of the antenna strip 6. c) Attach the antenna strip 6 to the front window as shown. Ensure that the antenna strip 6 is attached horizontally. ONLY FOR VEHICLES WITH RAIN SENSOR 6 Ensure that the top of the antenna is pushed against the body of the roof. 2. Peel off the release paper at the back of the RS-antenna and attach it to the coated area of the antenna strip 6 as shown. Fig. 5 Centre FOR VEHICLES WITHOUT RAIN SENSOR Centre 6 Ensure that the top of the antenna is pushed against the body of the roof. 3. Peel off the release paper at the back of the RS-antenna and attach it to the coated area of the antenna strip 6 as shown. Fig Corolla Verso (RH) - 2

13 ELECTRONIC TRAFFIC AVOIANCE INSTALLATION OF THE RS-TUNER For vehicles without prewired ETA-antenna FOR INSTALLATION OF NAVIGATION, PLEASE REFER TO THE NAVIGATION INSTALLATION MANUAL AIM Fit the RS-tuner to the RH side a bracket a using bolts c. c : Bolt (M5x8) (2x) Make sure that the RS-tuner installed at the lowest position. is c Fig a) Connect the P and 8P connector of the navigation harness to the navigation ECU 9. b) Connect the navigation 3P female connector to the RS-subwire harness 2 3P male connector. c) Connect the RS-subwire harness 2 3P female connector to the navigation ECU 9. Navigation harness 2 Fig. 8 WIRE SIE VIEW 3. a) Connect the RS-antenna black wired pin to the RS-subwire harness 2 2P connector to the second position from the left on the top row (wires face you and tab is on top). b) Connect the RS-subwire harness 2 2P connector to the RS-tuner. 2 2P Black wired pin Fig. 9 Corolla Verso (RH)

14 ELECTRONIC TRAFFIC AVOIANCE Turn 4. a) Connect the RS-antenna connector to the fakra connector 5 as shown. 5 Be careful not to close the fakra connector 5 before the RS-antenna connector is inserted till it clicks. b) Insert the fakra connector 5 with antenna to the RS-tuner. 5 Fig. 20 d 5. Fold the carpet and fit the navigation ECU 9 with the RS-tuner on the floor as shown using bolts d. d : Bolt (M8x2) (2x) Use foam tape e to mask the RStuner from view and place it between the floor and the RS-tuner for protection of the seat-wire harness. 9 d e Fig Corolla Verso (RH) - 4

15 ELECTRONIC TRAFFIC AVOIANCE For vehicles with prewired ETA-antenna c f 9. a) Release the navigation ECU 9 from the vehicle. b) Fit the RS-tuner to the ETAbracket 7 using the bolts c. c : Bolt (M5x8) (2x) c) Fit the RS-tuner between the cross member and the navigation ECU as shown. Use butyl tape f to attach the RS-unit to the navigation ECU. d) Place foam tape e to protect the lower corners of the RS-tuner as to protect the wire harness. e 7 Fig P WIRE SIE VIEW 2 Fig a) Connect the 3P and 8P connector of the navigation harness to the navigation ECU 9. b) Connect the navigation 3P female connector to the RS-subwire harness 2 3P male connector. c) Connect the RS-subwire harness 2 3P female connector to the navigation ECU 9. d) Connect the RS-antenna black wired pin to the RS-subwire harness 2 2P connector to the second position from the left on the top row (wires face you and tab is on top). e) Connect the RS-subwire harness 2 2P connector to the RS-tuner. f) Insert the RS-antenna connector in the fakra connector 5 as shown. Be careful not to close the fakra connector 5 before the RS-antenna connector is inserted till it clicks. g) Connect the fakra connector 5 with antenna to the RS-tuner. Corolla Verso (RH)

16 ELECTRONIC TRAFFIC AVOIANCE 3. Refit the navigation ECU Fig. 24 AFTER INSTALLATION AN FUNCTION CHECK, BE CERTAIN TO RE-FIT PANELS AN CONNECTORS CORRECTLY AN TIGHTEN ALL BOLTS TO THE SPECIFIE TORQUE SETTINGS IN LINE WITH THE REPAIR MANUAL Corolla Verso (RH) - 6

17 TOYOTA MOTOR CORPORATION

RAV4 TNS310 (Traffic) Plus

RAV4 TNS310 (Traffic) Plus TNS310 (Traffic) Plus RHD installation instructions Model year: 005 Vehicle code: **A3***-*****W Part number TNS310 Plus: Sub wire harness No 1: 08673-64801 Sub wire harness No : 08673-64800 Part number