EZ-LIGHT Indicators 4-Color, Multi-Function

Transcription

1 EZ-LIGHT Indicators -olor, Multi-Function Datasheet D-Operated Indicators with olors and Multiple Flashing Frequencies Rugged, cost-effective. and easy-to-install indicators available in K0, K0 Flat Pack, or K80 housing style Displays colors and multiple flashing frequencies: steady ON, flashing, or alternating Illuminated dome provides easy-to-see operator guidance and indication of equipment status ompact devices are completely self-contained, no controller needed hoose NPN or PNP input, depending on model Immune to ambient light, EMI, and RFI interference 8 Vdc to 0 V dc operation QPM ontact factory for more information. EURO-STYLE PIGTIL PUR LE LL FTORY WRNING: Not To e Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Models onstruction onnection LED Function Inputs K0LGRYPQ K0LGRYNQ 0 mm dome/ 0 mm mount polycarbonate PNP NPN K0FLGRYPQ K0FLGRYNQ 0 mm polycarbonate dome/ polycarbonate base Integral -pin M/Euro-style male quick disconnect (QD) olor: hoose Green, Red, Yellow or lue ON, flashing or alternative PNP NPN K80LGRYPQ K80LGRYNQ 0 mm dome/ Flat or DINmount polycarbonate PNP NPN For the K0L and K0FL Models: To order the 0 mm PV cable with QD model, replace the Q with a QP in model number (example, K0LGRYPQP). To order the m (6. ft) cable model, omit the suffix Q from model number (example, K0LGRYP). Models with a QD require a mating cable. For the K80L Models: To order the terminal-wired model, omit the suffix Q from model number (example, K80LGRYP). ontact fhe factory for other colors and color combinations. Original Document 79 Rev. D February 07 79

2 EZ-LIGHT Indicators -olor, Multi-Function Wiring Diagrams Function PNP Wiring NPN Wiring Wiring Key: = rown = White = lue = lack = Gray Indicator olor G R Y 8-0V dc Indicator olor G R Y 8-0V dc Green steady Green flashes Red steady Red flashes Yellow steady Yellow flashes lue steady lue flashes Green, Red flash cycle Red, lue flash cycle Green, Yellow flash cycle Green, lue flash cycle Red, Yellow flash cycle - Tel: P/N 79 Rev. D

3 EZ-LIGHT Indicators -olor, Multi-Function Function PNP Wiring NPN Wiring Yellow, lue flash cycle Green, Red, Yellow, lue flash cycle Specifications Supply Voltage and urrent 8 V dc to 0 V dc at 0 m maximum Indicators Entire translucent diffuser or dome provides indication. LEDs are independently selected: Green, Red, Yellow, or lue; ON steady or flashing, alternating or rotating Input Response Time Indicator ON: 0 ms maximum Indicator OFF: 0 ms maximum Operating onditions 0 to +0 ( 0 F to + F) Environmental Rating K0L and K0FL models: fully encapsulated, rated IE IP67and IP69K, per DIN abled models also meet IP69K if the cable and cable entrance are protected from high-pressure spray. K80L models: IE IP67 (encapsulated electronics) ertifications ll models: K0L models only: Indicator Flash Rate -olor: -second flash rate (00 ms ON) - and -olor Flash: 00 ms per color onstruction See Models table onnections Integral -pin M/Euro-style male quick disconnect (QD); 0 mm (6 in) PV cable with a -pin M/Euro-style male quick disconnect (QD); or m (6. ft) unterminated -wire PV cable depending on the model ordered Required Overcurrent Protection WRNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via urrent Limiting, lass Power Supply. Supply wiring leads < WG shall not be spliced. For additional product support, go to Supply Wiring (WG) Required Overcurrent Protection (mps) P/N 79 Rev. D - Tel:

4 EZ-LIGHT Indicators -olor, Multi-Function Dimensions K0L K0FL 0.0 mm (.97") Ø0 [.97"].6 [.76"] M0 x. (mounting nut included) Max. Torque. Nm (0 in-lbf) Internal Threads ½ - NPSM Max. Torque. Nm (0 in-lbf) 8 mm (.0")* 0 mm (0.79") mm (0.") 6.0 [0.6"] 60.0 [.6"] 0.0 [.8"].0 [.8"] x.0 [0.0"] x.0 [0.0"] x. [0."] 7.0 [0.67"] K80L 80.8 mm (.8") 6.0 mm (.6") 66. mm (.6") 09. mm (.") 6.0 mm (.6") X Ø. mm (Ø 0.") Max. Torque. Nm (0 in lbf) with supplied screws X 8 UN Max. Torque. Nm (0 in lbf) 6.0 mm (.0") M X Internal Threads ½ - NPSM Max. Torque. Nm (0 in lbf) ccessories -Pin Euro-Style ordsets -Pin Threaded M/Euro-Style ordsets Single Ended Model Length Style Dimensions Pinout (Female) MQD-0. MQD-06 MQD- MQD m (. ft).8 m (6 ft).7 m ( ft) 9. m (0 ft) Straight Typ. M x ø. = rown = White = lue = lack = Gray - Tel: P/N 79 Rev. D

5 EZ-LIGHT Indicators -olor, Multi-Function -Pin Threaded M/Euro-Style ordsets Single Ended Model Length Style Dimensions Pinout (Female) MQD-06R.8 m (6 ft) MQD-R.7 m ( ft) Typ. [.6"] Right-ngle 0 Typ. [.8"] MQD-0R 9. m (0 ft) M x ø. [0.7"] Mounting rackets ll measurements are listed in millimeters, unless noted otherwise. rackets for the K0L and K0FL Models Note: K0FL models include a 8 mm (.9 in) circular velcro mounting kit for easy mounting with no additional hardware SM0 Right-angle bracket with curved slot for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 0 mm sensor -ga. stainless steel 6 69 SM0S Swivel bracket with 0 mm mounting hole for sensor lack reinforced thermoplastic polyester Stainless steel mounting and swivel locking hardware included Hole center spacing: to =0 Hole size: =ø 6., = 7. x 6., =ø 0. Hole center spacing: =ø 0.8 Hole size: =ø 7.0, =ø 0.0 SM0F Swivel bracket with tilt and pan movement for precise adjustment Mounting hole for 0 mm sensor -ga. 0 stainless steel Easy sensor mounting to extrude rail T-slot Metric and inch size bolt available olt thread: SM0F, = /8-6 x in; SM0FM0, = M0 -. x 0 Hole size: = ø 0. SMMS0R Right-angle SMMS series bracket 0 mm hole for mounting rticulation slots for 90 + rotation -ga. (.6 mm) cold-rolled steel Hole center spacing: =6.0, to =.0 Hole size: =6.8 x 7.0, =ø 6., =ø.0 8 SM0MM -ga. stainless steel bracket with curved mounting slots for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 0 mm sensor SMMS0P Flat SMMS series bracket 0 mm hole for mounting rticulation slots for 90 + rotation -ga. 00 series stainless steel 9 Hole center spacing: =, to =. Hole size: =.6 x 7, = ø 6., = ø 0. Hole center spacing: =6.0, to =.0 Hole size: =6.8 x 7.0, =ø 6., =ø.0 P/N 79 Rev. D - Tel:

6 EZ-LIGHT Indicators -olor, Multi-Function SM0FVK V-clamp, flat bracket and fasteners for mounting to pipe or extensions lamp accommodates 8 mm dia. tubing or in. square extrusions 0 mm hole for mounting 6 8 Hole size: = ø SM0RVK V-clamp, right-angle bracket and fasteners for mounting to pipe or extrusion lamp accommodates 8 mm dia. tubing or in. square extrusions 0 mm hole for mounting Hole size: = ø 0. rackets for the K80L Models SMDX80D DIN-mount bracket for K80L models, mounts on mm DIN rail Hardware included to mount to K80L housing lack reinforced thermoplastic anner Engineering orp. Limited Warranty anner Engineering orp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. anner Engineering orp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the anner product. THIS LIMITED WRRNTY IS EXLUSIVE ND IN LIEU OF LL OTHER WRRNTIES WHETHER EXPRESS OR IMPLIED (INLUDING, WITHOUT LIMITTION, NY WRRNTY OF MERHNTILITY OR FITNESS FOR PRTIULR PURPOSE), ND WHETHER RISING UNDER OURSE OF PERFORMNE, OURSE OF DELING OR TRDE USGE. This Warranty is exclusive and limited to repair or, at the discretion of anner Engineering orp., replacement. IN NO EVENT SHLL NNER ENGINEERING ORP. E LILE TO UYER OR NY OTHER PERSON OR ENTITY FOR NY EXTR OSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR NY INIDENTL, ONSEQUENTIL OR SPEIL DMGES RESULTING FROM NY PRODUT DEFET OR FROM THE USE OR INILITY TO USE THE PRODUT, WHETHER RISING IN ONTRT OR WRRNTY, STTUTE, TORT, STRIT LIILITY, NEGLIGENE, OR OTHERWISE. anner Engineering orp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by anner Engineering orp. ny misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. ny modifications to this product without prior express approval by anner Engineering orp will void the product warranties. ll specifications published in this document are subject to change; anner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: anner Engineering orp. ll rights reserved