VS1RN5CV10 VS1RN5C10 NPN/DO 10 mm (0.4 in) VS1AP5CV10 VS1AP5C10 PNP/LO VS1RP5CV10 VS1RP5C10 PNP/DO

Transcription

1 V eries ensors Datasheet elf-contained Miniature ensors V to V dc operation Visible red or infrared sensing beam, depending on model (. in) or 5 mm (.6 in) convergent point, depending on model P (sinking) or PP (sourcing) output, and dark or light operate, depending on model -wire connection; output load capacity to 5 m hoice of integral cable or quick-disconnect connector WR: ot To Be Used for Personnel Protection. Power O ndicator 2. Received ignal ndicator. 2 m able or 5 mm (6 inch) Quick-Disconnect ever use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Visible Red (86 nm) Beam Models nfrared (865 nm) Beam Models Focus Output Type able OVRT VBL RD OVRT V5V V5 P/LO VR5V VR5 P/DO (. in) VP5V VP5 PP/LO VRP5V VRP5 PP/DO V5V2 V52 P/LO 2 m (6.5 ft) VR5V2 VR52 P/DO 5 mm (.6 in) VP5V2 VP52 PP/LO VRP5V2 VRP52 PP/DO Overview V eries miniature self-contained sensors are designed for precision sensing in small areas previously accessible only to remote or fiber optic models. Typical applications include mounting inside vibrating feeders and electronic component handling equipment, where larger sensors will not fit. The sensing energy of a convergent-mode sensor is concentrated at the specified focus point. onvergent-mode sensors are less sensitive to background reflections, compared with diffuse-mode sensors. ontact the factory if background reflections are a problem. To order 9 m cables models, add suffix W/ to the model number (e.g., V5V W/). To order 5 mm (6 inch) cable with threaded -pin Pico-style quick disconnect fitting models, add suffix Q to the model number (e.g., V5VQ). model with a QD connector requires a mating cable; see ccessories on page. Original Document 5665 Rev. 8 ovember

2 V eries ensors nstallation otes ncluded with each sensor is a hardware packet containing two stainless steel M2. Phillips pan-head machine screws, flat washers, lock washers, and hex nuts. To mount the sensor, use the supplied flat washer against the front surface of the sensor housing, between it and the screw head. f mounting to one of the optional brackets, place the lock washer against the back of the bracket, followed by the nut. f mounting directly to a threaded hole, place the lock washer between the screw head and the flat washer. For best results, mount the V where it is protected from moisture, high humidity and dirt.. Hex ut (2) 2. Lock Washer (2). Washer (2). M2. Phillips Pan-head Machine crew (2) 2 Wiring Diagrams P Outputs PP Outputs Key: - V dc V dc = Brown = Blue = Black = Load Load Load OT: QD hookups are shown. abled hookups are functionally identical Tel: P/ 5665 Rev.

3 V eries ensors pecifications upply Voltage and urrent V to V dc (% maximum ripple) at less than 25 m (exclusive of load) upply Protection ircuitry Protected against reverse polarity and transient voltages Output Protection ircuitry Protected against false pulse on power-up and continuous overload or short circuit of outputs. Overload trip point m. Output onfiguration PT solid-state switch P (current sinking) or PP (current sourcing), depending on model Light operate (.O.) or dark operate (..), depending on model Output Rating 5 m maximum OFF-state leakage current: < microamp at 2 V dc O-state saturation voltage: <.25 V at m dc; <.5 V at 5 m dc Output Response Time millisecond O and OFF Repeatability 25 microseconds ndicators reen O: sensor power O reen flashing: output overload mber O: light is sensed mber flashing: marginal excess gain ( to.5 times) in light condition onstruction Black B/polycarbonate housing with clear acrylic lens nvironmental Rating P5; M onnections 2 m (6.5 ft) attached cable: three #28 ga stranded conductors with P insulation; PV outer cable jacket; or 5 mm (6 inch) cable with -pin Pico-style quick-disconnect fitting. QD cables are ordered separately. Operating onditions 2 to +55 ( F to + F) 8% at +5 maximum relative humidity (non-condensing) pplication otes M2 stainless steel mounting hardware included (see nstallation otes). Optional mounting brackets are available (see ccessories list). ertifications Performance urves Table : Visible Red Beam Models 2 xcess ain Beam Pattern V...V."." V eries Visible Red onvergent Mode DT."." V eries Visible Red onvergent Mode.6" 8 mm.".7" DT.6".79".2".8".".".8".2" V...V2."." V eries Visible Red onvergent Mode DT."." V eries Visible Red onvergent Mode.".8".2" DT.6" 5 mm 2.".2".6".8".8".6".2" 2 Performance based on 9% reflectance white card test P/ 5665 Rev. - Tel:

4 V eries ensors Table 2: nfrared Beam Models 2 xcess ain Beam Pattern V...."." V eries nfrared onvergent Mode DT." ".6" V eries nfrared onvergent Mode 8 mm.".7" DT.6".79".2".8".".".8".2" V...2."." V eries nfrared onvergent Mode DT." "." V eries nfrared onvergent Mode.8".2" DT.6" 5 mm 2.".2".6".8".8".6".2" Dimensions 25.7 mm (.") 5 mm (.59").5 mm (.5"). (.6") 8. (.") 9. (.6"). (.6") Ø2. (.9"). 5 mm (6 in) able ccessories -Pin Threaded M8/Pico-tyle ordsets Model Length tyle Dimensions Pinout (Female) PKM-2 PKM-5 PKM-7 2 m (6.56 ft) 5 m (6. ft) 7 m (22.97 ft) 5 Typ. traight ø 9.5 PKM-9 PKM- 9 m (29.5 ft) m (2.8 ft) M8 x = Brown = Blue = Black - Tel: P/ 5665 Rev.

5 V eries ensors Brackets MBVT Tall right-angle bracket tainless steel Hole center spacing: = 6.8 Hole size: =.5 x 2. 2 MBVT Tall right-angle compact bracket stainless steel Hole center spacing: = 5.5 Hole size: = ø MBV hort right-angle bracket 8-ga. stainless steel Hole center spacing: = 6.8 Hole size: =.5 x 2. 2 MBV hort right-angle bracket 8-ga. stainless steel Hole center spacing: =. Hole size: = ø Banner ngineering orp. Limited Warranty Banner ngineering orp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner ngineering orp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. TH LMTD WRRTY LUV D LU OF LL OTHR WRRT WHTHR PR OR MPLD (LUD, WTHOUT LMTTO, Y WRRTY OF MRHTBLTY OR FT FOR PRTULR PURPO), D WHTHR R UDR OUR OF PRFORM, OUR OF DL OR TRD U. This Warranty is exclusive and limited to repair or, at the discretion of Banner ngineering orp., replacement. O VT HLL BR R ORP. B LBL TO BUYR OR Y OTHR PRO OR TTY FOR Y TR OT, P, LO, LO OF PROFT, OR Y DTL, OQUTL OR PL DM RULT FROM Y PRODUT DFT OR FROM TH U OR BLTY TO U TH PRODUT, WHTHR R OTRT OR WRRTY, TTUT, TORT, TRT LBLTY, L, OR OTHRW. Banner ngineering orp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner ngineering orp. opyright otice ny misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. ny modifications to this product without prior express approval by Banner ngineering orp will void the product warranties. ll specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. For the most recent version of any documentation, refer to: Banner ngineering orp. ll rights reserved. Banner ngineering orp. ll rights reserved