A Member of the. Integrated Metering Technologies

Transcription

1 I n s t a l l a t i o n M a n u a l A Member of the Integrated Metering Technologies

2 1.0 General and Safety Do not install, operate or maintain this flow meter without reading, understanding and followingthe factory-supplied instructions. Otherwise, injury or damage may result. Read these instructions carefully before beginning installation and save them for future reference. Observe all warnings and instructions marked on the product. Consider handling and lifting instructions to avoid damage. If the product does not operate normally, refer to the service instructions or to a qualified ARAD service engineer. There are no operator-serviceable parts inside this product. 2.0 Product Liability and Warranty Arad s standard products (the Products ) are sold to Customer and are purchased by Customer under the terms of warranty set forth herein below: 1. Arad warrants that the Products shall, under conditions of normal use and when properly installed, administered, applied and maintained, be free from defects in material and workmanship (the Warranty ), for a period of 12 months following delivery thereof to Customer (the Warranty Period ). 2. Arad s sole obligation and liability under the Warranty shall be limited to the replacement, the repair or the refund of the original purchase price, at Arad s sole discretion, of any defective Products which are proven not to conform to the Products specification and which are returned to the factory or service center designated by Arad during the Warranty Period by the Customer after completing a failure report. All provided that written notice of such defect is given by the Customer to Arad within 21 days after discovery thereof. Freight cost to such factory or service center will be paid by the Customer and freight cost from such factory or service center to Customer will be paid by Arad. 3. Arad will not be responsible for and will have no obligation under the Warranty to any non-conformity of the Products, caused, in whole or in part, as a result of misuse, abuse, tampering with or modification of any of the Products and/ or by accidents, fault or negligence, improper administration, application and/or use, installation, service, repair and/or maintenance of the relevant Products, by act of vandalism or by any causes whatsoever (including but not limited to environmental conditions) that are external thereto. 4. The foregoing warranty is a limited warranty and is exclusive and in lieu of all other warranties, express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose and shall constitute the Customer s sole and exclusive remedy with respect thereto. Replacement or repair in the manner provided above will constitute fulfillment of all of Arad s obligations with respect to the quality and performance of the products. No dealer, distributor, agent or employee of either Arad or customer is authorized to modify these warranties. Such modification shall be null and void and shall not bind Arad for any and all purposes. 5. Except and to the extent provided under the warranty, in no event shall Arad be liable, whether in contract, tort or otherwise, for any damages, whether direct or indirect, consequential, incidental, special or punitive, resulting from any defect in the products, including, without limitation, loss of profits, business, income, anticipated savings, goodwill or other commercial loss, even if Arad had been advised of the possibility of such damages, except to the extent that such liability may not lawfully be excluded. Customer shall be solely responsible for the selection, use, efficiency and suitability of the Products. 3.0 Items Included With Order: One OCTAVE ultrasonic flow meter, size as indicated on the packaging box, pieced together into a complete compact system (flow tube plus electronics). One OUTPUT module, either digital or analog (based on the customer s order). 2

3 4.0 Supplied Documentation: Condensed installation and user manual. Report of factory meter settings. Certificate of calibration data. 5.0 Unpacking and Inspection This product has been thoroughly inspected and tested before shipment and is ready for operation. After carefully unpacking the meter, inspect for shipping damage before attempting to install. If any indication of mechanical damage is found, immediately contact the responsible transportation service and your local ARAD LTD. representative. 6.0 System Description and Measurement Method The OCTAVE s measurement method is based on an ultrasonic, transit-time, dual-beam sensor which determines the length of time it takes an ultrasonic sound wave to travel the distance between the two sensors located on the meter s body. The two sensors function as both the sender and the receiver, each one alternating these functions so that the ultrasonic wave travels both with and against the direction of the flow. Since the ultrasonic wave travels slower against the flow than with the flow, the time difference of two waves traveling with and against the flow leads to determining the velocity of the water. The OCTAVE ultrasonic flow meter is a battery-powered precision flow meter designed for linear, bidirectional flow measurement of water. Flow measurement values can be transferred through the standard digital or analog output. The OCTAVE can be set up for a wide range of applications. 7.0 Mechanical Data Maximum Working Pressure Liquid Temperature 16 bar 0.1 up to 50 º C Precision Class ISO 4064 rev.2005, Accuracy class 2 Configuration Power Source Environmental Protection Display Units Volume Display Options Outputs (optional) Coupling Threads (only 11/2 and 2 ) Compact - The display is built in to the unit 2 D size Li-battery: 10 years life time IP 68, Ambient operation temp. -25 C up to +55 C Multi line 9 digit LC display (Flow rate and volume units are programmable) 1. Net (Forward less reverse) 2. Forward only 3. Forward & reverse alternating 4-20mA (powered loop) Dual digital pulses process (open collector) Dry Contact Encoder output BSP, NPSM (See also instructions for installation of Octave with polymer body) Connections Flanges according to ISO, BS 10 and ANSI 150 Severity levels Pressure Loss ΔP 16 Environmental class C, mechanical class M1 Electromagnetic environment class E1 3

4 Dimensions Model Octave (mm) 40 Threaded 50 Threaded Nominal size (inch) 1½ Threaded 2 Threaded L Length without couplings (mm) W Width (mm) H Height (mm) h Height (mm) Weight (kg) - cast iron body Weight (kg) - polymer body H h L B 8.0 Mechanical Installation 8.1 Handling the Flow Meter Important handling information: Do not lift the Octave by the electronic housing. Do not carry the Octave by his lid. Do not place the Octave on the electronic housing. When handling the Octave, avoid hard blows, jolts or impacts. 8.2 Installation: Location and Position Installation requirements Proper Installation Wrong Installation 4

5 2 DN 2 DN The Following Examples are Arad s Recommendations For Achieving Top Performance When installing the Octave downstream of any hydraulic component (valve, pump) the recommended installation requirements no less than the drawings recommendations. For upstream & downstream straight pipes Please use as much as installation site will allows (longer the better). Install Pressure breaker after the meter - pipe length should be at least 2 pipe diameter (longer the better). 2 DN 2 DN 2 DN 2 DN FLOW DIRECTION 2 pipe diameters before and after elbows (90 ) Minimum of two (2) pipe diameters before and after 2 DN 2 DN 5 DN Minimum of five (5) pipe diameters after pumps Minimum of two (2) pipe diameters before T connections 2 DN FLOW DIRECTION Minimum of two (2) pipe diameters after strainers 2 pipe diameters before and after elbows (90 ) in vertical installations 5

6 9.0 Polymeric Octave Installation General Instructions Basic - Please follow the general instructions for water meters (Check Valve, upstream & down stream and system flushing on new installations). Exsisting and new installations: It is recommended that the meter will NOT be installed in the middle of the system, so the meter will not suffer from the load of all the installed fixtures. Please use rubber gaskets only (not fiberglass)! After adding the gaskets the gap between the end connection and the meter should be 1mm max. Please unscrew the end connection in order to keep the recommended distance. Please do not use force in order to close the gap. X Rubber gasket It is recommended that at least one side of meter will be connected to a PVC (or plastic) pipe. Please start to tighten the end connections by hand. Final tightening will be with no more than 100Nm torque In case it is not possible to use plastic end connections (at least on one side), please support the meter as shown in the drawing below. Please don t do any welding while the meter is connected to the pipe. Support Plastic end connection X Please make sure that the end connections are parallel and inline to each other. X X V V 6

7 10.0 Notes For proper flow measurements, the OCTAVE s measuring tube should be completely full at all times. Non-wetted sensors show loss of signal. Though this will not cause damage to the meter, it will, however, not measure flow and display zero. Flow direction: The OCTAVE is a bidirectional flow meter. Note the indicating arrow on the OCTAVE s display for forward and backward flows. In case of direct sunlight exposure, it is recommended to keep the lid closed, though no direct damage will occur with the lid open. Do not expose the OCTAVE to excessive vibration. To avoid vibration, support the pipeline on both side of the meter Ambient working temperature: -25 to +55 C. Water working temperature: 0.1 to +50 C. To avoid measuring errors due to air in the flow tube, observe the following precautions: Since air collects at the highest point of the system, installation of the flowmeter should be at the lowest point. Always install control valves downstream of the meter in order to avoid cavitation. ever install the meter on a pump suction side in order to avoid cavitation Counter Flanges Refer to the standard dimensional drawings for flange spacing, accommodating for the thickness of gaskets. Install meter in line with the pipe axis. The flange faces must be parallel to each other. Permissible length deviation: Lmax - Lmin 0.5mm (0.02 ) Start-up DDCheck that the meter has been installed correctly. DDCheck that the flow rate and volume units are correctly preprogrammed on the display. DDCheck that the output module is correctly attached Digital Display m 3 m3/h Volume units Flow rate units Leak detector Battery level Flow direction Alarm/Error Output Mode 7

8 14.0 Electrical Outputs The OCTAVE has several outputs options. 1. Dual pulse output for volumes. 2. Analog output (4-20mA) for flo Pulse Module Specification Pulse types: 1. Open collector that allows current loading of 200mA, and up to 50volt. 2. Dry contact. Outputs Diagram Octave Pulse v5.1 Long Cable 100ohm RED 1 Pulse#1 EMI / RFI / OverVoltage PROTECTION 100ohm GREEN BLACK 1 1 Pulse#2 GND Read-out instrument SHIELD 1 GROUND Ground Cable 1 Cables Warning - Signal connection polarity is mandatory! Short Cable Wire Function Red Pulse Out#1 Long cable Green Pulse Out#2 Black GND Open Ground / Shield Short cable Ring Terminal Ground Output Characteristics Outputs Type Cable Length - supplied Maximum Cable Length* Maximum Applied Voltage Open Drain 1.5/5 [meter] 500 [meter] 30 [Vdc] * The maximum Cable length depends on: Cable type, controler and electrical noise level Cable Teldoor PN or similar 8

9 Dry Contact Module Specification Outputs Diagram Long Cable Octave Dry Contact v1.0 Out#1 Out#2 Read-out instrument 24Vdc GROUND Cables Short Cable Long cable Short cable* Wire Function Red + Orange Out#1 Black + Brown Out#2 Red 24V + Black 24V - Yellow GROUND * Signal connection polarity is mandatory! Output Characteristics Outputs Type Cable Length - supplied Maximum Cable Length* Supply Voltage Dry Contact 1.5/5 [meter] 500 [meter] 24 [Vdc] * cable Teldoor PN or similar 9

10 mA Module (Analog) The current output is a passive 4-20mA. 4mA is always 0 (zero) flow and the 20mA is factory programmable according to the customer requirements.. (If the customer did not specify, the 20mA will be the maximum flow rate). Outputs Diagram Long Cable (+) Octave 4/20mA module Shield Read-out + - instrument (-) GROUND GROUND Short Cable Cables Signal connection polarity is mandatory! Wire Function Red current loop + Long cable Black current loop - Open GROUND / SHIELD Short cable Ring Terminal GROUND Output Characteristics Outputs Type 4-20mA current output Supplied Cable Length 1.5/5 [meter] Maximum Cable Length * 500 [meter] Loop supply voltage [Vdc] Output Impedance 25 [M] typ * cable Teldoor PN or similar 10

11 15.0 Output Module Installation If your Octave order includes output module, the following will explain how to attach it to the meter. Output module kit includes (Pic.1). 1. Output module 2. 2 Allen Screws 3mm X 20mm 3. O-ring 4. Sealing cap 5. 3mm Allen key Pic. 1 Stage 1: Using the 3mm Allen key disassemble the cover (Pic. 2) from the meter, keep the cover the screws and the O-ring for future use (Pic.3). Pic. 2 Pic. 3 Stage 2: Place the O-ring in the groove (Pic.4 & 5). Make sure the O-ring is placed correctly - this part is most important for the continuous operation of the meter! Pic. 4 Pic. 5 Stage 3: Insert the output module into the plug (Pic.6), and tighten the screws with the 3mm Allen key (Pic.7). Pic. 6 Pic. 7 Stage 4: Push the sealing cap to the lower hole of the module (Pic.8) and fixed it all the way in with a hammer (Pic.9). Pic. 8 Pic. 9 11

12 Innovation through precision, quality and performance Arad Ltd Dalia, ISRAEL Tel: (972) Fax: (972) w w w. a r a d. c o. i l S e p t e m b e r