EZ-BEAM "S2" Series Sensors

Transcription

1 Z-BM "2" eries ensors Designed for use on ensor BU etworks Features Low cost and easy to use; no adjustments are necessary ensor selection is simply a matter of choosing a housing style and sensing mode Models available for opposed (through-beam), polarized retroreflective, and fixed-field diffuse modes dvanced self-diagnostics with separate alarm output; dual LD system indicates sensor performance olid-state outputs for direct connection to a BU system network junction such as a Banner BU DPOT 4-pin quick disconnect connector for standard euro-style extension cables poxy-encapsulated circuitry; leakproof P67 (M 6P) rating for harsh sensing environments Brackets available for several mounting options Description "2" eries Z-BM sensors are designed to connect directly to a "smart" BU system network junction, such as the Banner BU-DPOT. 2 eries sensors are internally wired to take advantage of the Z-BM's marginal signal LRM output. The LRM output is normally open (.O.) and conducts whenever the sensor's excess gain drops to between and.5 in the light condition. The sensing signal output is also normally open, which means that the output conducts when light is sensed (i.e. - light operate). n order to take advantage of the second LRM output, 2 sensors require the use of BU DPOT junctions which offer two channels per input. Both sensor outputs are PP (current sourcing) for direct connection to a BU network junction using standard 4-pin euro-style extension cables. 2 eries sensors offer all of the features and powerful sensing performance that Z- BMs offer. The innovative dual-indicator system takes the guesswork out of sensor performance monitoring. Housings are tightly sealed and the sensor circuitry is epoxy-encapsulated for reliable duty in wet or oily sensing environments. Models are available for opposed (through-beam), polarized retroreflective and fixed-field diffuse sensing (see chart on page 2, for available ranges). s the chart on page 2 shows, there are three basic housing styles. The "" style is a threaded barrel which is available in 8 mm or 3 mm diameters. The "Q" style offers either 25 mm or 4 mm right-angle rectangular housings. Finally, the "T" style is a patented right-angle design available with either an 8 mm or 3 mm threaded lens. The "T" style combines the mounting ease of a barrel sensor with the low-profile advantage of a right-angle design. everal mounting options are offered, including angled brackets and split-clamp brackets. 2 series sensors may also be simply mounted through suitable clearance holes. ee page 7 for more information. U.. Patent # Printed in U P/ 4546

2 2 eries Family ensor Package vailable ensing Modes and Ranges Opposed Retro Fixed-field 8 8 mm barrel 2 m (6 ft) 2 m (79 in) 5 mm (2 in) mm () 3 3 mm barrel 6 m (2 ft) 6 m (2 ft) 2 mm (8 in) 4 mm (6 in) Q25 25 mm rectangular 2 m (6 ft) 2 m (79 in) 5 mm (2 in) mm () Q4 4 mm rectangular 6 m (2 ft) 6 m (2 ft) 2 mm (8 in) 4 mm (6 in) T8 8 mm right-angle 2 m (6 ft) 2 m (79 in) 5 mm (2 in) mm () T3 3 mm right-angle 6 m (2 ft) 6 m (2 ft) 2 mm (8 in) 4 mm (6 in) page 2 Banner ngineering orporation

3 2 eries Opposed Mode mitter () and Receiver (R) Models Range able upply Voltage Output Type xcess Gain Beam Pattern 86Q 82P6RQ Q256Q Q252P6RQ T86Q T82P6RQ 2 m (66 ft) 4-pin uro QD -3V dc PP G. m.33 ft m 3.3 ft 8, Q25 and T8 eries DT Opposed Mode m 33 ft m 33 ft 5 mm mm 5 mm 5 mm mm 5 mm ffective Beam: 3 mm (.5") 8, Q25 and T8 eries Opposed Mode 5 m 6 ft m 32 ft 5 m 48 ft DT 2 m 64 ft 25 m 8 ft 6 in 2 in 2 in 6 in 36Q 32P6RQ Q46Q Q42P6RQ T36Q T32P6RQ 6 m (2 ft) 4-pin uro QD -3V dc PP G 3, Q4 and T3 eries. m.33 ft Opposed Mode m 3.3 ft DT m 33 ft m 33 ft 75 mm 5 mm 25 mm 25 mm 5 mm 75 mm ffective Beam: 23 mm (.9") 3, Q4 and T3 eries Opposed Mode 5 m 5 ft 3 m ft 45 m 5 ft DT 6 m 2 ft 75 m 25 ft 6 in 2 in 2 in 6 in Retroreflective Mode Models Range able upply Voltage Output Type xcess Gain Beam Pattern 82P6LPQ Q252P6LPQ T82P6LPQ 2 m (79 in) 4-pin uro QD -3V dc PP G. m.33 ft. m.33 ft 8, Q25 and T8 eries DT with BRT-3 Reflector m 3.3 ft m 33 ft 5 mm mm 5 mm 5 mm mm 5 mm 8, Q25 and T8 eries with BRT-3 Reflector.5 m.6 ft. m 3.2 ft.5 m 4.8 ft DT 2. m 6.4 ft 6 in 2 in 2 in 6 in 2.5 m 8. ft 32P6LPQ Q42P6LPQ T32P6LPQ 6 m (2 ft) 4-pin uro QD -3V dc PP G. m.33 ft. m.33 ft 3, Q4 and T3 eries DT with BRT-3 Reflector m 3.3 ft m 33 ft 5 mm mm 5 mm 5 mm mm 5 mm 3, Q4 and T3 eries with BRT-3 Reflector.5 m 5 ft 3. m ft 4.5 m 5 ft DT 6. m 2 ft 7.5 m 25 ft 6 in 2 in 2 in 6 in Banner ngineering orporation page 3

4 2 eries Fixed-field Mode Models Range able 82P6FF5Q Q252P6FF5Q T82P6FF5Q 82P6FFQ Q252P6FFQ T82P6FFQ 32P6FF2Q Q42P6FF2Q T32P6FF2Q 32P6FF4Q Q42P6FF4Q T32P6FF4Q 5 mm (2 in) mm () 2 mm (8 in) 4 mm (6 in) 5 mm far limit cutoff upply Voltage Output Type 4-Pin uro QD -3V dc PP mm far limit cutoff 4-Pin uro QD -3V dc PP 2 mm far limit cutoff 4-Pin uro QD -3V dc PP 4 mm far limit cutoff 4-Pin uro QD -3V dc PP xcess Gain Performance based on 9% reflectance white test card G. mm. G. mm. G mm. G mm. 8, Q25 and T8 eries mm. DT mm. DT Fixed-field mode with 5 mm far limit cutoff mm. 8, Q25 and T8 eries mm. DT Fixed-field mode with mm far limit cutoff mm. 3, Q4 and T3 eries Fixed-field mode with 2 mm far limit cutoff mm. mm 3, Q4 and T3 eries Fixed-field mode with 4 mm far limit cutoff DT mm mm mm mm mm page 4 Banner ngineering orporation

5 2 eries upply Voltage and urrent Opposed Mode mitter Opposed Mode Receiver Fixed-field upply Protection ircuitry Product pecifications to 3V dc (% maximum ripple); upply current (exclusive of load current): 25 m 2 m 3 m 35 m Protected against reverse polarity and transient voltages Output onfiguration ensing Output: PP (current sourcing), light operated larm Output: PP (current sourcing), normally open and conducts whenever the sensor's excess gain drops to between and.5 in the light condition Output Rating Output Protection ircuitry Output Response Time Repeatability ndicators onstruction nvironmental Rating onnections Operating Temperature Vibration and Mechanical hock 5 m maximum (each); the total load may not exceed 5 m; Off-state leakage current < microamp at 3V dc; On-state saturation voltage <V at m dc; <.5V at 5 m dc Protected against false pulse on power-up and continuous overload or short-circuit of outputs Opposed: 3 milliseconds "on" and.5 milliseconds "off" and Fixed-field: 3 milliseconds "on" and "off" OT: millisecond delay on power-up; outputs are non-conducting during this time Opposed: 375 microseconds and Fixed-field: 75 microseconds Repeatability and response are independent of signal strength Two LDs: Green and Yellow GR glowing steadily = power to sensor is "on" GR flashing = output is overloaded YLLOW glowing steadily = normally open output is conducting YLLOW flashing = excess gain marginal (-.5x) in light condition Housings are VLO thermoplastic polyester; Lenses are Lexan (opposed models) or acrylic (retro and fixedfield models) 8 and 3 come with two jam nuts; T8, T3, Q25 and Q4 come with one jam nut Leakproof design rated M 6P; P67 4-pin euro-style quick-disconnect fitting; cables are ordered separately -4 to +7 (-4 to 58 F); Maximum relative humidity 9% at 5 (non-condensing) ll models meet Mil. td. 22F requirements. Method 2 (Vibration; frequency to 6 Hz, max., double amplitude.6-inch acceleration G). Method 23B conditions H& (hock: 75G with unit operating; G for non-operation) Banner ngineering orporation page 5

6 2 eries Dimension nformation 8 Green LD Power ndicator Yellow LD Output ndicator Jam uts (2 Provided) 8 x mm Thread 3 Yellow LD Output ndicator Green LD Power ndicator Jam uts (2 Provided) M3 x.5 Thread 78.7 mm (3.") 37. mm (.46") 77.5 mm (3.5") 53. mm (2.9") Q25 Yellow LD Output ndicator Green LD Power ndicator 25. mm (.98") 35. mm (.38") 5.2 mm (.6") 2.7 mm (.5") 3. mm* (.8") 2.4 mm (.49") (Jam ut upplied) Lens enterline M8 x Thread Q4 4. mm (.58") 5. mm (.97") 9.8 mm (.78") Yellow LD Output ndicator Green LD Power ndicator (Jam ut upplied) 46. mm (.8") 82.5 mm (3.25") Lens enterline 2. mm (.79") M3 x.5 Thread T8 Jam ut (upplied) M8 x Thread T3 Jam ut (2 upplied) M3 x.5 Thread ø5 mm (.59") 3. mm (.8") Yellow LD Output ndicator ø3. mm (.8") ø5 mm (.59") 45. mm (.77") Yellow LD Output ndicator ø4. mm (.57") Green LD Power ndicator Green LD Power ndicator.5 mm (.45") 56.6 mm (2.23").5 mm (.45") 66.5 mm (2.62") Quick Disconnect Pin Detail connector on sensor shown (male pins) Hookup nformation mitter Quick Disconnect Pin Detail connector on sensor shown (male pins) larm (White wire) + to 3V dc (Brown wire) ot used (White wire) + to 3V dc (Brown wire) D common (Blue wire) ensing output (Black wire) D common (Blue wire) ot used (Black wire) ote: Wire colors are for Banner MQD-4 eries quick disconnect cables page 6 Banner ngineering orporation

7 2 eries MB8 Mounting Brackets MB3 * Use 4 mm (#8) screws to mount bracket. Drill screw holes 24.2 mm (.95 in) apart. 3 3 mm (.2 in) 8.5 mm (.73 in) 25.4 mm (. in) 4 mm (.6 in) * Use 5 mm (#) screws to mount bracket. Drill screw holes 4. mm (.58 in) apart. 45 mm (.8 in) mm (.52 in) 6 mm (2.) ø 3.5 mm (.2 in) R 24.2 mm (.95 in) ø 4.6 mm* (.8 in) 46 mm (.8 in) 4.6 mm* (.8 in) 7.6 mm (.3 in) R 4 mm (.58 in) ø 6.3 mm (.25 in)* 6.3 mm (.25 in)* 7.6 mm (.3 in) 69 mm (2.7 in) MB8Q (for Q25 series) * Use 4 mm (#8) screws to mount bracket. Drill screw holes 24.2 mm (.95 in) apart. 3 3 mm (.2 in) 9 mm (.75 in) 25.4 mm (. in) 4 mm (.6 in) MB3Q (for Q4 series) * Use 5 mm (# screws to mount bracket. Drill screw holes 4. mm (.58 in) apart mm (.8 in) 38.5 mm (.52 in) 6 mm (2.) ø 3.7 mm (.2 in) mm (.) R 24.2 mm (.95 in) ø 4.6 mm (.8 in)* 46 mm (.8 in) 4.6 mm (.8 in)* 7.6 mm (.3 in) mm (.) R 4 mm (.58 in) ø 6.3 mm (.25 in)* 6.3 mm (.25 in)* 7.6 mm (.3 in) 69 mm (2.7 in) MB8 4. mm (.6 in) 3 mm (.5 in) MB3 56. mm (2.2 in) 3 mm (.5 in) 42.4 mm (.67 in) 2. mm (.83 in) 63. mm (2.48 in) 3.5 mm (.2) 4. mm (.55 in) 3. mm (.8 in) 2.5 mm (. in) ut Plate M5 x.8 x 6 mm crew (2) 3.5 mm (.53 in) 45. mm (.77 in) 2.5 mm (. in) ut Plate M5 x.8 x 8 mm crew (2) MB8 MB mm (.75 in) 46. mm (.8 in) 25.4 mm (. in).9 mm (.43 in) pacer (f Required) 63.5 mm (2.5 in) ot hown: (2) M5 x.8 x 6 mm screws are supplied for clamping bracket together 2.2 mm (.48 in) 82.5 mm (3.25 in) 3. mm (.5 in) 36. mm (.42 in) 2.5 mm (. in) ut Plate M5 x.8 x 6 mm crew (2) 6.4 mm (.25 in) 5.8 mm (2. in) 43.2 mm (.7 in) M5 x.8 x 3 mm crew (2) 25.4 mm (. in) Banner ngineering orporation page 7

8 2 eries WRRTY: Banner ngineering orporation warrants its products to be free from defects for one year. Banner ngineering orporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.! WRG These photoelectric presence sensors do OT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. sensor failure or malfunction can result in either an energized or a de-energized sensor output condition. ever use these products as sensing devices for personnel protection. Their use as a safety device may create an unsafe condition which could lead to serious injury or death. Only M-R, MULT-R, MH-GURD and PRMTR-GURD ystems, and other systems so designated, are designed to meet OH and machine safety standards for point-of-operation guarding devices. o other Banner sensors or controls are designed to meet these standards, and they must OT be used as sensing devices for personnel protection. Banner ngineering orp., 974 Tenth ve. o., Minneapolis, M 5544 Telephone: (62) F (applications) (62)