Wireless Remote Transmitter Kit

Transcription

1 Wireless Remote Transmitter Kit INSTALLATION INSTRUCTIONS KIT # Part # Wireless Kit Rev. 8/13

2 COMPONENT IDENTIFICATION AND KIT PARTS 14 Receiver Antenna 5 Kit Contents Wireless Remote Transmitter Kit KIT # INSTALLATION INSTRUCTIONS Wiring Harness 0 Part # Wireless Kit Rev. 7/ PHW ASSEMBLY Transmitter NG Assembly Antenna 19 Receiver Factory Linked Wiring Harness 15 NG ASSEMBLY Part # Wireless Kit Rev. 8/13 Page

3 HANDHELD WIRELESS PARTS LIST ITEM PART NO. DESCRIPTION QTY Instructions, Wireless Install, 4VAC Transmitter Wireless Handheld Base Receiver, Wireless 6 Relay, 4VAC Wiring Harness, Wireless P1, 36" Wiring Harness, Wireless P, 36" Antenna, Wireless, 900MHZ Socket, Plug, Panel 9-Pin, Male s Terminal, Female Socket Connector, Elect. 3-Pin Male Label, Wireless Transmitter 1 ITEM PART NO. DESCRIPTION QTY Clamp, Hose, ST Assy, Wireless s Label, Wireless Kit Nut, 1/4" Flange, ZN Wrap, Spiral, 1/" Black/Ft 50'/RL 1.5 ft Connector, Butt BSVVV 14X-M Wire, MTW, 16 GA Black/Ft.15 ft s Carton Kraft RS 10 x 10 x Kit, Wireless 4VAC n Screw, 1/4" x 1-1/4" Whiz Loc s Not Shown n NG Machine Only Field Replacement Only Part # Wireless Kit Rev. 8/13 Page 3

4 PHW INSTALLATION INSTRUCTIONS To ensure the successful installation and assembly of this wireless remote transmitter kit, read and follow these instructions and refer to the exploded view before attempting to install. Check contents of package with parts list. Step 1: Cool machine down before installing kit. Unplug machine from power source and relieve pressure from discharge hose. Nuts Base Receiver Antenna 90 Studs Step : Jumper Remove the 9-pin jumper plug from the bottom of the electrical junction box and discard. Step 3: Plug the two male harness plugs into the wireless base receiver. The plugs are color coded with unique keyways to maintain the correct polarity of the plugs. Step 4: Install wireless base receiver onto two studs located on electrical junction box. Make sure harness connectors face towards inside of machine. Secure base to electrical box using two 1/4" flange nuts (item 14). Step 5: Install antenna onto wireless base receiver. The antenna base should be rotated to the 90 position. Directional Arrow Hose Clamp DETERGENT VALVE VALVULA DE DETERENTE SOUPAPE DE DETERGENT Amber Step 6: Plug the 3-pin power plug and the 9-pin plug into the female plugs located underneath the electrical junction box. Step 7: Cut the braided detergent hose 3" below the detergent valve. Using two hose clamps (item 11) on both ends of the braided detergent hose, install the electric solenoid valve (item 1). Be careful to orient the valve with the directional arrow pointing down. Step 8: Plug machine into a power source. Observe LED lights on the wireless base receiver. The "" indicator light will pulse green and the "" indicator light will be a solid amber. Part # Wireless Kit Rev. 8/13 Page 4

5 NG INSTALLATION INSTRUCTIONS To ensure the successful installation and assembly of this wireless remote transmitter kit, read and follow these instructions and refer to the exploded view before attempting to install. Check contents of package with parts list. Step 1: Cool machine down before installing kit. Unplug machine from power source and relieve pressure from discharge hose. Base Receiver Screws Antenna Jumper Nut Nut Step : Remove the 9-pin jumper plug from the bottom of the electrical junction box and discard Step 3: Plug the two male harness plugs into the wireless base receiver. The plugs are color coded with unique keyways to maintain the correct polarity of the plugs Step 4: Insert mounting screws (item 0) through holes in the electrical junction box and secure with nuts. Place wireless base receiver onto two screws and secure base to electrical box as shown using two 1/4" flange nuts (item 14). Step 5: Install antenna onto wireless base receiver. The antenna base should be rotated to vetical position Directional Arrow Hose Clamp DETERGENT VALVE VALVULA DE DETERENTE SOUPAPE DE DETERGENT Amber Step 6: Plug the 3-pin power plug and the 9-pin plug into the female plugs located underneath the electrical junction box. Step 7: Cut the braided detergent hose 3" below the detergent valve. Using two hose clamps (item 11) on both ends of the braided detergent hose, install the electric solenoid valve (item 1). Be careful to orient the valve with the directional arrow pointing down. Step 8: Plug machine into a power source. Observe LED lights on the wireless base receiver. The "" indicator light will pulse green and the "" indicator light will be a solid amber. Part # Wireless Kit Rev. 8/13 Page 5

6 OPERATING INSTRUCTIONS Step 1: Plug the machine into a power source. Step : With the transmitter in your hand, push and hold the #6 button to turn on the transmitter. The "TX" LED light will flash green. Step 3: Push and release button #1 to turn pump on. #1 PUMP ON ENGINE OFF # PUMP OFF Step 4: Push and release button #3 to turn burner on. The "Burner ON/OFF" LED light will illuminate red. Step 5: Push and release button #5 to turn the detergent on. The "Detergent On/OFF" LED light will illuminate amber. #3 BURNER ON #5 DETERGENT ON/OFF #4 BURNER OFF #6 TRANSMITTER ON/OFF Step 6: Push and release button #5 to turn the detergent off. The "Detergent ON/OFF" LED light will go out. Step 7: Push and release button #4 to turn burner off. The "Burner On/OFF" LED light will go out. Wait for the machine to cool down properly before shutting pump off. Step 8: Push and release button # to turn the pump off Step 9: Push button #6 to turn the handheld transmitter off. The handheld transmitter can be turned off at any time during the operation of the machine, to conserve battery power. Turning off the handheld transmitter will leave the machine in its current state of operation. The transmitter will need to be turned back on to change the operational modes of the machine. Part # Wireless Kit Rev. 8/13 Page 6

7 WIRING EXPLODED VIEW Female Socket Terminal Part # Wireless Kit Rev. 8/13 Page 7

8 WIRING DIAGRAM Part # Wireless Kit Rev. 8/13 Page 8