INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30

Size: px
Start display at page:

Download "INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30"

Transcription

1 Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) For Fax on Demand Technical Assistance (800) (Must be a Registered Dealer to Use Fax on Demand System)

2 Index Step 1: Component Installation Step 2: 10-Pin Main Harness Installation Step 3: 5-Pin Power Harness Installation Step 4: Wire Loop Programming Step 5: Optional Accessory Connections Step 6: Transmitter Programming Step 7: Remote Feature Programming Step 8: Multiple Car Programming Step 9: General Testing Step 10: Speciality Feature and Optional Equipment Test Specifications Wiring Diagram Warning! Do not plug the 10-pin or 5-pin wire harness into the alarm control module before you begin installing the alarm. The wire harnesses must be plugged into the alarm control module after all connections are made. Failure to follow this procedure could cause some confusion with transmitter operation and or alarm function operation. Step 1: Component Installation Mounting the Control Module: Find a suitable location to secure the alarm control module within the passengers compartment of the vehicle. Never mount the alarm control module in the engine compartment or in the trunk. In addition, never mount the alarm control module in the direct path of the heater. Secure the alarm control module by using wire ties or drill two 1/8 holes and secure the module to the frame of the vehicle with the screws provided. Installing Hood/ Trunk Pin Switches: Provided with the alarm kit is one pin switch and one mounting bracket. To install the switch either in the truck or under the hood, find a suitable location where the switch will make contact with the hood or trunk lid and will not get wet. Use the bracket provided or drill a 1/4 hole in the desired location. Mounting the Override / Valet Switch: Mount this switch in a hidden but accessible location within reach of the driver of the vehicle. Drill a 1/4 hole and use the nuts and washers provided to secure the switch. Run the wires from the switch to the alarm control housing location. 2

3 Step 1: Component Installation (Continued) Installing the Alarm Status LED: The LED indicator provided utilizes a push in type mounting. Drill a 5/16 hole in the desired location, feed the wires through the hole and push the LED into place. Run the wires to the location of the alarm control module. Step 2: 10-Pin Main Harness Installation The main wire harness contains 8 wires which all have a specific purpose. Follow the wiring recommendations enclosed for each wire. Wires not used should be released from the harness connector or taped off to prevent accidental shorting. Included with the 10-pin wire harness are two loose wires, an orange wire and a white wire with black stripe. See main harness and power harness wiring instructions for these two loose wires. (Page 4) Main Harness Vacant Sockets First Vacant Socket (Located in the 1st Position) Second Vacant Socket (Located in the 8th Position) First Vacant Socket: (For Use with ALA-RPT Relay Pack Only) See Optional Accessory Connection for proper wiring. (Page 10) Gray Wire: (Pulsed Ground for Car Horn) The gray wire is a pulsed ground output designed to activate the vehicle s existing car horn system in place of or in addition to a siren sounding device. Connect the gray wire to the negative trigger wire on the vehicle s horn relay. WARNING! Maximum output of this wire is 300mA. Horn systems requiring positive voltage or more than 300mA to trigger the horn relay will require an additional relay to increase current capabilities. Blue Wire with White Stripe: (No Connection) Brown Wire: (Optional Siren + Output) Connect the brown wire to the positive wire from the siren. Ground the remaining wire from the siren for proper operation. Blue Wire: (Optional Grounding Sensor Input) The blue wire is an instant grounding trigger input for optional hood/trunk grounded pin switches or any electronic sensor. 3

4 Step 2: 10-Pin Main Harness Installation (Continued) Green Wire: The green wire is the negative (-) door trigger input. If the vehicle you are working on has a negative (-) triggered dome light system, connect the green wire to the common dome light trigger wire. This wire is usually located at the driver s side door jamb switch. Violet Wire: The violet wire is the positive (+) door trigger input. If the vehicle you are working on has a positive (+) triggered dome light system, connect the violet wire to the common dome light trigger wire. This wire is usually located at the driver s side door jamb switch. Second Vacant Socket: The second vacant wire socket provides a 1 second pulsed ground (300mA) output when channel #2 is activated. (See Optional Accessory Connections) (Page 10) Red / White: (Pulsed Parking Light Relay Output) Connect the red/white wire to the parking light wire coming from the headlight switch. (Do not connect the red/white wire to the dashboard lighting dimmer switch. Damage to the dimmer will result) use a volt meter to test the connection point before connecting the red/white wire. While checking, rotate the dimmer switch to make sure you do not have the dimmer lead. The limitation of the red/white wire is 10 Amp max. Do not exceed this limit or damage to the alarm and parking light relay will result. Pink: (Parking Light Relay Input) The pink wire is the input to the flashing parking light relay. The connection of the pink wire will determine the output polarity of the flashing parking light relay. Connect the pink wire to (+) battery to have (+) output from the relay or connect the pink wire to frame ground to have ground output from the relay. Step 3: 5-Pin Power Harness Installation The power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed for each wire. Power Harness 4

5 Step 3: 5-Pin Power Harness Installation (Continued) Red Wire: (Main Power Input) Connect the red wire directly to the (+) battery post for best operation of the alarm system. For best current sensing capability from the alarm s current sensing circuit, connect the red wire to the constant power wire coming from the interior dome light. Black Wire: (Main Ground Input) Connect the black wire directly to the frame of the vehicle. Use a bolt and nut to secure the wire. Scrape away any grease or paint that might prevent a good connection. Yellow Wire: (Switched +12 Volts From the Ignition Switch) Connect the yellow wire to a +12 volt wire that is switched on and off by the ignition key. The correct wire will indicate +12 volts when the ignition key is in the on and start positions. Do not connect the yellow wire to the acc wire coming from the ignition switch. Step 4: Wire Loop Programming The PL30 control module offer 2 programmable features. Follow the instructions enclosed to program these features using the wire loop wires in the control module White Wire Loop: (Passive Arm Locking Control) Leave the white wire loop connected to allow the door locks to lock when the alarm automatically arms. Cut the white wire loop to prevent the door locks from locking when the alarm automatically arms. Green Wire Loop: (Current Sensing On/Off) Leave the green wire loop connected for the current sensing trigger circuit to be active. Cut the green wire loop to eliminate the current sensing trigger circuit. 5

6 Step 5: Optional Accessory Connections Power Door Lock / Unlock Activation 3 Wire Positive Trigger Door Lock System Lock Control Switch (+) Lock Out +12 Volts Input (+) Unlock Out Black Wire: Connect to Lock Orange Wire: No Connection Red Wire: Connect to Unlock 3 Pin Black Plug Note: Prewired Door Lock Interconnect T-Harness are Available for Most Vehicles To Alarm To Door Lock Control Relays 3 Wire Ground Trigger Door Lock System Lock Control Switch (-) Lock Out Ground Input (-) Unlock Out Black Wire: Connect to Unlock Orange Wire: No Connection Red Wire: Connect to Lock 3 Pin Black Plug To Alarm To Door Lock Control Relays Note: Prewired Door Lock Interconnect T-Harness are Available for Most Vehicles 5 Wire Ground at Rest Door Locking Systems 3 Pin Black Plug Red Wire: Lock Orange Wire: No Connection Black Wire: Unlock ALA-DL1 Relay Pack 87 87A A Violet Wire White Wire: Lock Brown Wire: Unlock Green Wire: Lock Blue Wire: Unlock Note: Prewired Door Lock Interconnect T-Harness are Available for Most Vehicles To +12 Volts (Battery +) To Power Lock Switch To Power Lock Motors 6

7 Step 5: Optional Accessory Connections (Continued) Mercedes Door Lock Activation Red Wire: Lock 3 Pin Black Plug Orange Wire: No Connection Black Wire: Unlock Lock 87A A Unlock Cut Green Wire B+ Unlock Door Lock Switch Lock To +12 Volts (Battery +) Door Lock Compressor Newly Installed Power Door Lock Motors Red Wire: Lock 3 Pin Black Plug Orange Wire: No Connection Black Wire: Unlock ALA-DL1 Relay Pack 87 87A A Violet Wire White Wire Brown Wire Green Wire: Lock Blue Wire: Unlock To +12 Volts (Battery +) To Ground To Newly Installed Power Door Lock Motors One Wire Multiplexing Door Locking Systems Some vehicle s (Chrysler, Mazda and Ford Probe and others) use one wire to lock and unlock the doors. Example: When the door lock controller sees a signal thru a resistor it will unlock. If a signal is received without a resistor the doors will lock. Some use 2 resistors. One for lock and one for unlock. We have developed patented plug-in fuse resistors for this application. Simply remove the fuse from our door lock module and replace with correct resistor value fuses that matches the vehicles door lock switch. ALA-DL1 Wiring: 1. Connect both the green (lock) and the blue (unlock wires to the vehicles one wire lock/unlock wire. 2. Connect our violet polarity input wire to +12v or to ground. To match vehicles door lock polarity 3. The white and the brown wires will not be used. Black 3-Pin Plug ALA-DL1 Lock Fuse 1 Unlock Fuse 2 Green Wire Blue Wire To Vehicles Lock/Unlock Wire Violet Wire To B+ or Ground as Required White Wire No Connection Brown Wire No Connection 7

8 Step 5: Optional Accessory Connections (Continued) Starter Disable Wiring Using ALA-RPS Relay Pack Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the Start Only Wire coming from the ignition key switch and cut it. B. Connect the ends of the cut start wire the black wires coming from the ALA-RPS relay pack. C. Plug in the orange 2-pin plug into the orange socket located at the rear of alarm module. To test the starter disable system refer to the starter disable testing procedures located in the testing section of this manual. (Page 16) Red Wire (Ign. Switched +12VDC) Black Wire (Ground when Armed Alarm Output) "OFF" "ON" "ACC" "START" 87 87a Cut ALA-RPS Relay Pack Starter Starter Disable and Engine Disable Using Optional ALA-RPS2 Relay Pack Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the Start Only wire coming from the ignition key switch and cut it. B. Connect the ends of the cut start wire the black wires coming from the ALA-RPS2 relay pack. C. Locate the power supply wire to any of the fuel management circuits listed below and cut it. D. Connect the ends of the cut wire the white wires coming from the ALA-RPS2 relay pack. E. Plug in the orange 2-pin plug into the orange socket located at the rear of alarm module. To test the dual circuit disable system, refer to the starter disable testing procedures located in the testing section of this manual. (Page 16) Orange 2-Pin "ACC" "OFF" Red Wire Black Wire ALA-RPS2 "ON" Black Wire "START" CUT 87 87a Black Wire Starter White Wire "ACC" 87 87a "OFF" "ON" CUT "START" White Wire Power Supply to Fuel Pump Power Supply to Ignition Coil or ECM Power Supply to Fuel Injectors 8

9 Step 5: Optional Accessory Connections (Continued) Parking Flashing Lights Parking Lights Headlight Switch Red Wire with White Stripe Output from Alarm Piggyback Connection Parking Lights Only Valet / Override Switch with 2-Pin Blue Plug Alarm Status LED Indicator with White 2-Pin Plug: Alarm Plug the Status white 2-pin LED plug Connection into white receptacle located in the side of the control module. Single Zone Electronic Sensor Plug Red Wire: +12 Volt Sensor Power Supply Black Wire: Sensor Ground Supply Blue Wire: Sensor Alarm Trigger Input Green Wire: No Connection 4 Pin White Plug 9

10 Step 5: Optional Accessory Connections (Continued) #2 Button Power Trunk Activation Using Optional ALA-RPT Relay Pack Insert Red Wire into the First Socket Insert Black Wire into the Eighth Socket Black Wire Red Wire ALA-RPT Relay Pack Orange Wire Output to Trunk Switch Purple Wire Input to Relay (+ or -) #2 Button Power Trunk Activation Using Optional 30 Amp Relay Insert White Wire with Black Stripe into the Eighth Socket White Wire with Black Stripe 87 Output to Power Trunk Switch To Constant +12 Volts (SPST ALA984H Relay Not Supplied) Input to Relay (+ or -) 10

11 Step 6: Transmitter Programming Step 1 Step 2 Valet/Override Switch ON ON Make Sure the Valet/Override Switch is in the Off Position OFF Switch in Off Position OFF Switch in On Position Plug In the Power Harness The horn/siren will start sounding, the parking lights will flash and the LED will begin flashing Step 3 ON Step 4 1x Step 5 2x Turn On Ignition Switch the Valet Switch On then Off 1 Time The horn/siren will stop sounding, the parking lights will stop flashing Switch the Valet Switch On then Off 2 Times The horn/siren will chirp 1 time. You are now in the transmitter code programming mode. The LED will be a solid RED 11

12 R Step 6: Transmitter Programming (Continued) Step 6 Regular #2 Arm/Dis R #2 Regular Arm/Dis Regular Arm/Dis #2 Code Hopping LOCK PANIC UNLOCK AUX Push Arm/Disarm (Regular) or Lock Button (Code Hopping) The LED will begin flashing slowly and the horn/siren will emit 1 short chirp. The code has now been learned. Note 1: Regular transmitters supplied are Not coded alike so you need to code in the second transmitter now by pushing the Arm/Dis button on the second transmitter. Go to Step 7. Note 2: Code Hopping transmitters supplied are Not coded alike so you need to code in the second transmitter now by pushing the Lock button on the second transmitter. Note 3: If you are coding a Code Hopping transmitters, skip steps 7 and 8 and go to step 9. No further coding procedures are necessary. Code hopping transmitters learn all button functions when the Lock button is learned. Step 7 1x Step 8 To Code #2 Button Switch the Valet Switch On then Off 1 Time The LED will be solid red and the horn/siren will chirp 1 time. Push the #2 Button The LED will begin flashing slowly and the horn/siren will chirp 2 times. Note 1: Regular transmitters supplied are Not coded alike so you need to code in the second transmitter now by pushing the #2 button on the second transmitter. OFF Step 9 12 Turn Off the Ignition The horn/siren will emit 1 short chirp and 1 long chirp. You are now out of the consumer transmitter code learning mode. The LED is off.

13 Step 7: Remote Feature Programming When the security system control module learns the transmitter operating code, a specific group of operating features are automatically programmed to a default setting. These default settings can be changed by following the enclosed procedure and using the consumer transmitter for programming. # Programmable Alarm Feature Default Setting 1 Chirp Status Indicator On 2 Last Door Closed Automatic Arming Automatic Arming of Alarm Off 3 Ignition Key Controlled Door Lock/ Unlock Off Step 1 Step 2 Valet/Override Switch ON ON OFF Switch in Off Position OFF Switch in On Position R Make Sure the Valet/Override Switch is in the Off Position Disarm the Security System The LED will be off and the horn/siren will emit 2 chirps Step 3 ON Step 4 6x The LED will remain off. Turn On the Ignition Switch the Valet Switch On then Off 6 Times The LED will be on solid and the horn/siren will emit 1 long then 1 short chirp. You are now in the Remote Feature Programming mode. 13

14 R Step 7: Remote Feature Programming (Continued) Step 5 Regular Arm/Dis #2 Regular Arm/Dis #2 Regular Arm/Dis #2 Code Hopping LOCK UNLOCK PANIC AUX # Transmitter Button Function Confirmation = Change Function 1 ARM/DIS or LOCK Chirp Status Indication 1 Beep = Chirp Status Indication On * 2 Beeps = Chirp Status Indication Off 2 #2 or UNLOCK Last Door Closed 1 Beep = Automatic Arming On, Alarm will arm 10 seconds after Automatic Arming door is closed and rearm 10 seconds after remote disarm. 2 Beeps = Automatic Arming On, Alarm will arm 20 seconds after door is closed and rearm 20 seconds after remote disarm. 3 Beeps = Automatic Arming On, Alarm will arm 30 seconds after door is closed and rearm 60 seconds after remote disarm. 4 Beeps = Automatic Arming Off * 3 ARM/DIS + #2 Ignition Key Controlled 1 Beep = Door will Lock 3 seconds after Ignition is Turned On. or Door Locks Door will not Unlock when Ignition is Turned Off. LOCK + UNLOCK 2 Beeps = Door will Lock 3 seconds after Ignition is Turned On Door will Unlock when Ignition is Turned Off. 3 Beeps = Door will not Lock 3 seconds after Ignition is Turned On. Door will not Unlock when Ignition is Turned Off *. * Indicates Default Settings Step 6 OFF Turn Off the Ignition The horn/siren will emit 1 short chirp and 1 long chirp. You are now out of the Remote Feature Programming mode. The LED is off. Step 8: Multiple Car Programming About Multiple Car Programming: Note 1: Regular transmitters with 2 buttons can operate 2 alarm systems. (Alarm models do not have to be the same) Note 2: Code hopping transmitters will only operate 1 alarm system. To perform multi-car programming, all transmitters must first be marked car to indicate which car/alarm they are for. ie car #1, car #2 etc. Once this is done, follow the specific programming procedure for each model alarm you are programming and program the arm/disarm button and CH#2 buttons according which car they will operate. 14

15 Step 9: General Testing To test the basic functions of the alarm system repeat the following procedures. 1. Turn off the ignition key and exit the vehicle closing all protected entrances. 2. Press the arm/disarm or lock button on the transmitter. You will hear a horn/siren chirp, the parking lights will flash one time and the LED status indicator will flash at normal speed. 3. Wait 5 seconds, then open a protected entrance. The horn/siren will begin to sound. Press the arm/disarm or unlock button once again and the horn/siren will stop sounding. (No Disarm Chirp Indicator) Note: If you disarm the alarm when the horn/siren is sounding, there are no disarming chirps. When you disarm the alarm when the siren is off, there will be disarming chirps. 4. Follow procedures 2 and 3 for all other protected entrances. Step 10: Speciality Feature and Optional Equipment Testing Each specialty feature listed operates in the same manner regardless of the alarm model. Test each feature by following the procedures enclosed to insure proper operation. Remote Panic: 1. Press and hold the arm/disarm (for regular transmitters) or panic button (for code hopping transmitter) down for approximately 3 seconds. 2. The alarm will begin to sound and the parking lights will begin to flash. 3. Press the arm/disarm or panic button once again and the horn/siren will stop sounding and the lights will stop flashing. Note: The remote panic feature has an automatic shut off circuit. When the horn/siren has sounded for 60 seconds, the panic circuit will turn itself off automatically. Last Door Automatic Arming: (If Programmed On) Note: The automatic arming feature will not operate unless the alarm input triggers have been connected directly to the existing or newly installed door jamb pins. Current sensing alone will not activate the automatic arming circuit. 1. Disarm the alarm. 2. Set the ignition key to the on position, then turn it off. 3. Exit the vehicle. The horn/siren will chirp 1 time when the door is closed. 4. The LED will begin to flash fast. 5. After 10, 20 or 30 seconds have passed (depending on remote feature programming), you will hear a single chirp. The alarm is now armed. 6. The LED will flash at a regular rate indicating an armed condition. Note: When the automatic arming feature is activated, so is the RF tamper re-arm circuit. Every time the alarm is disarmed by remote, the RF tamper re-arm circuit will count for sixty seconds (LED will be flashing fast) and the alarm will re-arm itself if no one has entered the vehicle. 15

16 Step 10: Speciality Feature and Optional Equipment Testing Override Operation: (Security System is Armed) 1. Enter the vehicle and the security systems will begin sounding at this point. Make sure that the valet/override switch is in the off position 2. Place the ignition key into the ignition switch and turn the ignition switch to the on position. 3. Within 5 seconds of turning the ignition key on, place the valet switch to the on position. 4. The horn/siren will stop sounding. 5. The LED indicator will be solid red. The security system is overridden and is now in the valet mode! Note 1: If the valet switch is already in the on position when you turn on the ignition key, the override function will be bypassed. Turn off the ignition key, place the valet switch in the off position and try again. Note 2: If you fail to place the valet switch to the on position within 5 seconds of turning on the ignition key, the override function will be locked out. Place the valet switch in the off position, turn off the ignition key and try again. Valet Operation: (The security system is already disarmed) 1. Make sure that the valet switch is in the off position. 2. Turn the ignition key to the on position 3. Place the valet switch to the on position. 4. The LED will be on solid indicating that the security system is in the valet mode. Note: If the unit is in valet mode the LED will be on solid when the ignition key is on only. When the ignition key is off the LED will flash once every 5 seconds. How to Get Back to Security System Activation Mode: 1. Place the ignition key switch to the on position. 2. Place the valet switch to the off position. 3. Place the ignition key switch back to the off position. You will notice that the LED indicator will be off. This indicates that you have exited the valet mode and your security system will operate normally. Starter Disable: (If Installed) (Also Applies to Fuel Management Disable if Installed) 1. Enter the vehicle and close all the entrances. 2. Arm the alarm using the transmitter. 3. Turn the ignition key to the start position. The engine will not crank over. 4. Turn the ignition key to the off position and disarm the alarm. 5. Turn the ignition key back to the start position and the engine will crank over and start. 16

17 Step 10: Speciality Feature and Optional Equipment Testing LED Status Indicator Operation: LED is off = Alarm is disarmed. LED is flashing = Alarm is armed. LED is flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood/ trunk or electronic sensor. LED flashing in a 3 flash hold sequence = Tamper warning, alarm was triggered by an open door. LED is on steady = Alarm is in the valet mode. (Ignition key is on ) LED flashes once every 5 seconds = Alarm is in the valet mode. (Ignition key is off ) LED is flashing fast = Automatic arming timer is counting down or RF tamper rearming timer is counting down. Parking Light Flash Alarm Status Indication: One light flash = Alarm is armed. Two light flash = Alarm is disarmed. Three light flash = Tamper indicator, alarm is disarmed. Horn/Siren Chirp Alarm Status Indication: Note: This feature can be programmed off, see Remote Feature Programming for details. One chirp = Alarm is armed and all input trigger wires are clear. Two chirps = Alarm is disarmed and has not been tampered with. Chirps once, pauses then chirps again = Alarm is armed but sensor is by-passed. Four chirps = Tamper indicator, alarm is disarmed. Power Door Lock/Unlock: (If Installed) 1. Arm the alarm with the transmitter, the locks will become locked. 2. Disarm the alarm with the transmitter, the locks will become unlocked. RF Tamper Re-Arm: Note: This feature is activated automatically when the alarm is programmed for automatic arming. See Remote Feature Programming for details. (Page 13-14) 1. Alarm must be programmed for automatic arming. 2. Close all protected entrances and arm the alarm with the remote transmitter. The LED will be flashing at a normal rate. 3. Wait 5 seconds and disarm the alarm using the remote transmitter. The LED will begin to flash fast. (Automatic arming indicator) 4. Wait 60 seconds and the alarm will become rearmed. 5. Repeat steps 1 through 4. When the LED starts flashing fast, open one of the protected entrances (door) the LED will be off and remain off. 60 Second Re-Arm Timer and Re-Lock Function: Once the alarm is triggered, the siren will sound for 60 seconds and then stop. The alarm will remain in an armed condition. If the door locks have been installed into the system, they will re-lock when the alarm resets after 60 seconds. 17

18 Step 10: Speciality Feature and Optional Equipment Testing Ignition Controlled Door Locking: (Door lock activation must be installed) When programmed on in Remote Feature Programming, ignition controlled locking is active 3 seconds after the ignition key is set the on position, the door locks will automatically become locked. When the ignition key is turned to the off position, the door locks will unlock. Note: If a protected entrance (Door) is open when the ignition key is set to the on position, the door locks will not lock. This is a non-deletable protective measure. Channel #2 Output: Press and hold the channel #2 activation button for 3 seconds. The designated channel 2 output wire from the alarm will pulse ground voltage for as long as button #2 is pressed. Specifications Power Requirements Volts Negative Ground Trigger Inputs... Grounded Pin Switch, Positive Pin Switch, Electronic Sensor Ground, 0.6 Volt Current Drop Current Requirements... Less Than 15mA Armed or Disarmed Timers... Programmable Automatic Arming Timer Programmable Re-Arming Timer 60 Second RF Tamper Re-Arming Timer 5 Second Zone By-Pass Re-Activation Timer Grounded Output Wire Capacity (White Wire).. 500mA Siren Output Wire Capacity... 2 amps Channel 2 Pulsed Output mA By-Pass Zones Zones Transmitter Frequency mHz Regular TX Code Combinations ,000 Available Code Hopping TX Code Combinations Billion Available Code Method... Digital Trinary Receiver Channels... No More Than 3 18

19 Wiring Diagram PL30 Green Wire Loop Cut to Eliminate Current Sense Trigger White Wire Loop Cut to Prevent the Door Locks from Locking When Alarm Automatically Arms Auxilliary Interrupt Socket (Orange) (See Optional Accessory Connection) Valet/Override Socket Plug-In LED (Blue) (White) Power Door Lock Harness Socket (Black) Shock Sensor Socket (White) Back View of Housing Power Door Lock Sensor Valet L.E.D. Black Wire Antenna (Do Not Ground) Auxilliary Wire Loops PL30 Controller Power Harness Main Harness Channel #2 Output Pulsed Ground (See Optional Accessory Connection) Gray Wire Pulsed Ground for Car Horn (Ground) Blue/White Wire No Connection Brown Wire Siren Output (+) Blue Wire Negative AUX Trigger Input Green Wire Negative Door Pin Trigger Input Violet Wire Positive Door Pin Trigger Input Red/White Wire Parking Lights Relay Output Pink Wire Parking Lights Relay Input Black Wire Ground to Vehicle Frame Yellow Wire To Ignition Switched +12V Red Wire To Battery +12V 19

20 rev. A PL30IM

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50 Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be

More information

INSTALLATION MANUAL. Model: PLUS Vehicle Security

INSTALLATION MANUAL. Model: PLUS Vehicle Security R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White.

MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White. MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM H7/1 Green : (-) 200mA Pulse H7 3 Pin H7/3 Blue : (-) 200mA Unlock White LED Indicator Valet Switch H6 2 Pin

More information

Model APS-101N Installation Manual

Model APS-101N Installation Manual Programmable Features Model APS-101N Installation Manual Select By Operating Transmitter Press Lock Button Press Unlock Button Siren Indications 1 Chirp 2 Chirps Factory Default 1) Arming Method Passive

More information

6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM

6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM 6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM Button 1 Button 2 Button 5 Button 3 Button 4 Standard Features: Two 5-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:

More information

Security and Keyless Entry Installation Guide ca 1051

Security and Keyless Entry Installation Guide ca 1051 PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1051 ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection

More information

DLKEK3HN INSTALLATION INSTRUCTIONS

DLKEK3HN INSTALLATION INSTRUCTIONS DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE

More information

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

INSTALLATION GUIDE. FCC ID NOTICE

INSTALLATION GUIDE.  FCC ID NOTICE REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This

More information

Remote Start with Keyless Entry Installation Guide ca5054

Remote Start with Keyless Entry Installation Guide ca5054 PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4

More information

MM1 Installation Instructions

MM1 Installation Instructions MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or

More information

2 Way Security and Keyless Entry Installation Guide ca 1553

2 Way Security and Keyless Entry Installation Guide ca 1553 PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location

More information

Manual - Inside Front Cover (Blank)

Manual - Inside Front Cover (Blank) FRONT COVER Manual - Inside Front Cover (Blank) Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procecures... 2 Wiring Diagram... 3 14 Pin Connector...4 Installation

More information

OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 670 1 MEGA 670 2 OCT/21/02 OCT/21/02 WIRING DIAGRAM H7: 10 Pin White

More information

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause

More information

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of

More information

Remote Start with Keyless Entry Installation Guide CA 5051

Remote Start with Keyless Entry Installation Guide CA 5051 PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION

More information

FEB/20/2003 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1

FEB/20/2003 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1 INTRODUCTION FEB/20/2003 INSTALLER WARNINGS This Remote Starter with Alarm System is designed to be installed

More information

CA-110 Installation Instructions

CA-110 Installation Instructions CA-110 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS

ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS CS-882 OEM ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATI PRECAUTIS & WARNINGS NOTE: This system does not improve or affect the range of the factory remote keyless entry transmitters.

More information

Security and Remote Start Installation Guide for models: ca6554

Security and Remote Start Installation Guide for models: ca6554 PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6554 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...4 Wire Connection Guide...5

More information

FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES

FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES #STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 72 Two-Way 5-Channel 915Mhz Remote Start Security System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty

More information

RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)

RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH

More information

Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST

Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST ca6552/6552sst. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Security and Remote Start Installation Guide for models: ca6553 ca6553sst

Security and Remote Start Installation Guide for models: ca6553 ca6553sst PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6553 ca6553sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 4 Wire

More information

Diablo 2 /AMX 68/AT-58 Installation Manual 3/31/99

Diablo 2 /AMX 68/AT-58 Installation Manual 3/31/99 1 Table of Contents Required Installation Tools... 2 Important Information... 2 Wiring Diagram.... 3 14 Pin Con nec tor... 4 Starter Dis able Relay...4 Installation Procedures...5 Control Unit... 5 Antenna...

More information

VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1

VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections

More information

MEGA WAY LCD REMOTE ENGINE STARTER AND CAR ALARM SECURITY. Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2700 INSTALL 1

MEGA WAY LCD REMOTE ENGINE STARTER AND CAR ALARM SECURITY. Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2700 INSTALL 1 MEGA 2700 2-WAY LCD REMOTE ENGINE STARTER AND CAR ALARM SECURITY Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2700 INSTALL 1 2 1. Blue: (-) Unlock Pulse. Or (+)Lock Pulse. 3. Green: (-) Lock

More information

FEB.20, 2003 COMMANDO MODEL FM-870 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST872 1

FEB.20, 2003 COMMANDO MODEL FM-870 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST872 1 COMMANDO MODEL FM-0 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST2 1 HJKL TABLE OF CONTENTS: INSTALLATION DIAGRAM..... 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION.... 6 H1/1 Violet Wire

More information

KE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

KE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. KE 680 DELUE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD Installation And Operation Manual MEGATRONI CALIFORNIA, U.S.A. KE 680 1 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10

More information

VS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

VS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 255 4-CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 255 1 VS 255 2 INTRODUCTION INSTALLER WARNINGS This Remote Starter with Alarm

More information

12V PROGRAMMABLE POWER OUT

12V PROGRAMMABLE POWER OUT Page 1 ACCESSORIES STARTER IGNITION BATTERY WIRES SIDE VIEW BLUE RED YELLOW 30 A 10 A BLUE / WHITE YELLOW WHITE / BLUE WHITE / DOOR TRIGGER See opt. 16 DOOR TRIGGER (input positive) See opt. 16 PARKING

More information

Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions

Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions Model PRO 9842 Installation Manual Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical

More information

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152 PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide ca 5152 1 Table of Contents Before You Begin... 3 Wire Connection Guide... 4 11 Pin Main Harness...

More information

FM SECURITY AND REMOTE START SYSTEM

FM SECURITY AND REMOTE START SYSTEM FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED 100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS

FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Remote Keyless Entry and Alarm System by Crimestopper Security Products Inc. This

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Remote Keyless Entry Installation Guide ca 2051

Remote Keyless Entry Installation Guide ca 2051 PROFESSIONAL SERIES Remote Keyless Entry Installation Guide ca 2051 ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

Button 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition

Button 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition WWW.STELLAR.COM Button Function Condition 1 a. Arm and lock doors b. Car finder with sound c. Temporary stop alarm from sounding d. Remote lock doors 1 for 2 sec. Panic Anytime a. Alarm is disarmed b.

More information

CA-210 Installation Instructions

CA-210 Installation Instructions CA-210 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

INSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN.

INSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN. FOR NEGATIVE PARKING LIGHTS (MOST JAPANESE VEHICLES) FOR POSITIVE PARKING LIGHTS TRUNK RELEASE CIRCUIT DIAGRAM: OUT TO TRUNK 12V 2nd CHANNEL AUXILIARY (GRAY WIRE) 86 a 85 If the power trunk release requires

More information

VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1

VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10 Pin White

More information

AUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!

AUTOMATIC TRANSMISSION ONLY!  Technical Support: ext 1 Warning!! REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 52 Two-Way 2-Channel Remote Start with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For

More information

VS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

VS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 200 4-CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 200 1 INSTALLATION DIAGRAM Two Way Transceiver Antenna H7 8 Pin Black Connector

More information

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet

More information

6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL

6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL 6 REAY SYSTEM 5-BUTTON SERIES VEHICE SECURITY SYSTEM INSTAATION MANUA Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the

More information

Model AX-510 Owner s Manual

Model AX-510 Owner s Manual Model AX-510 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with

More information

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products

More information

REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001FC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Covers All 35xx Series Advanced 2-Way Remote Starters. Technical Support: ext 0

Covers All 35xx Series Advanced 2-Way Remote Starters.   Technical Support: ext 0 INSTALL GUIDE Covers All 35xx Series Advanced 2-Way Remote Starters www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service

More information

CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc.

More information

INSTALLATION GUIDE OWNER S GUIDE

INSTALLATION GUIDE OWNER S GUIDE INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 2-3 Making Connections...

More information

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products

More information

"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV

WE'VE GOT THE EDGE ON SECURITY INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV "WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT INC. 1997 Contents 5 WIRE HARNESS CONNECTIONS Black Wire (Chassis Ground)...

More information

Model APS-510C Installation Manual Remote Control Vehicle Security System

Model APS-510C Installation Manual Remote Control Vehicle Security System Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power

More information

K9-Mundial-2. ver. a color cover. Owner's Guide & Installation Instructions. MA_K9-Mundial-2/REV0 4/01 COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 2001

K9-Mundial-2. ver. a color cover. Owner's Guide & Installation Instructions. MA_K9-Mundial-2/REV0 4/01 COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 2001 K9-Mundial-2 NOTE: This is a place marker cover ver. The production unit has a color cover ver. Owner's Guide & Installation Instructions MA_K9-Mundial-2/REV0 4/01 COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT

More information

DLRM DLRM

DLRM DLRM Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components

More information

RA2 Installation Manual Rev. B

RA2 Installation Manual Rev. B Important Information Required Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional

More information

AS-4000 OPERATING INSTRUCTIONS (PS-5000)

AS-4000 OPERATING INSTRUCTIONS (PS-5000) AS-4000 OPERATING INSTRUCTIONS (PS-5000) BASIC OPERATIONS This unit is a state-of-the-art combination of a vehicle alarm and remote starter system. Start by familiarizing yourself with the alarm functions

More information

MEGA WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER. Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 2700 OPERATE 1

MEGA WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER. Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 2700 OPERATE 1 MEGA 2700 2-WAY LCD PAGER ALARM WITH REMOTE ENGINE STARTER Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 2700 OPERATE 1 2 WARNINGS: As with any product that performs automatic functions, there

More information

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Press and release the valet switch 3 times 1 Chirp - LED 1 flash Y Model PRO-9800 Installation Manual SELECTABLE FEATURES Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check

More information

INSTALLATION MANUAL. 328i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY

INSTALLATION MANUAL. 328i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY INSTALLATION MANUAL 328i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY 1 Table Of Contents Wiring Connections Black Wire (Chassis Ground)... 3 Red Wire (Constant Power)... 4 Yellow Wire (Ignition Input)...

More information

Remote Start Installation Guide ca 4552

Remote Start Installation Guide ca 4552 PROFESSIONAL SERIES Remote Start Installation Guide ca 4552 ca4552. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness...

More information

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended

More information

REC-11+ REMOTE RECEIVER UNIT

REC-11+ REMOTE RECEIVER UNIT Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous

More information

Table of Contents. Owner s Guide

Table of Contents. Owner s Guide Table of Contents Owner s Guide Arming the System...2 Disarming the System...3 Emergency Override... 4 System Armed & Activated...4 Remote Controller Icons...5-6 Panic... 6 Sensor By-Pass... 6 Auxiliary

More information

CA-510a Installation Instructions

CA-510a Installation Instructions CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

CSI-300 Installation Instructions

CSI-300 Installation Instructions CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

C3-RS-915 INSTALLATION MANUAL

C3-RS-915 INSTALLATION MANUAL C3-RS-915 PROFESSIONAL 2-WAY 915 MHz. LCD REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Voltage & Temperature Sensor And Two Way Serial Port Data Link INSTALLATION MANUAL Compatible THIS PRODUCT

More information

Advanced Remote Vehicle Starting System

Advanced Remote Vehicle Starting System INSTALLATION GUIDE 1600 Advanced Remote Vehicle Starting System 1600M AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. WARNING!!

More information

Model PRO 9644a Installation Manual

Model PRO 9644a Installation Manual Model PRO 9644a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch operate as custom code. Be certain to place a check mark

More information

INTRODUCTION ALARM WIRING DESCRITION

INTRODUCTION ALARM WIRING DESCRITION 6PIN CONNECTION RED BLUE YELLOW BROWN PINK INTRODUCTION The newest technological are integrated in our Two Way Alarm and Remote Engine Start alarm system. They are fully programmable for your customers

More information

INSTALLATION MANUAL. 533i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY

INSTALLATION MANUAL. 533i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY INSTALLATION MANUAL 533i 2 COPYRIGHT1997:CRIMEGUARDKEYLESSENTRY &SECURITY 1 Table Of Contents Wiring Connections Black Wire (Chassis Ground)... 3 Red Wire (Constant Power)... 4 Yellow Wire (Ignition Input)...

More information

WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECTOR

WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECTOR EVO-ONE WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECT (6-PIN) BYPASS RELAY (+) Foot Brake Black IN 750mA (-) Parking lights Pink OUT 750mA (-) Trunk Release/AUX Yellow/Black OUT (-) Hand Brake Brown/

More information

CS-2002DC & CS-2002DC Series II

CS-2002DC & CS-2002DC Series II CS-2002DC & CS-2002DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security

More information

INSTALLATION MANUAL. 745i 2 COPYRIGHT 1997: CRIME GUARD KEYLESS ENTRY & SECURITY

INSTALLATION MANUAL. 745i 2 COPYRIGHT 1997: CRIME GUARD KEYLESS ENTRY & SECURITY INSTALLATION MANUAL 745i 2 COPYRIGHT 1997: CRIME GUARD KEYLESS ENTRY & SECURITY 1 Table Of Contents Wiring Connections Black Wire (Chassis Ground)... 3 Red Wire (Constant Power)... 4 Yellow Wire (Ignition

More information

INSTALLATION GUIDE Table of Contents

INSTALLATION GUIDE Table of Contents CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2

More information

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 OPERATION: A. TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock

More information

Lt.Blue/Black. White. Orange. LED Blue LED Yellow LED Red

Lt.Blue/Black. White. Orange. LED Blue LED Yellow LED Red EVO-ONE RFK1004 WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECT (6-PIN) BYPASS RELAY (+) Foot Brake Black IN 750mA (-) Parking lights Pink OUT 750mA (-) Trunk Release/AUX Yellow/Black OUT (-) Hand

More information

Model CSI-300 Owner s Manual

Model CSI-300 Owner s Manual Model CSI-300 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped

More information

Model PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable

Model PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable Model PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable FEATURES:! 2 Four Button Programmable RF Transmitters! Four Channel Code Learning Receiver

More information

IN VEHICLE SECURITY ULTIMATE FLEXIBILITY. Installation Supplement. ClassicOne & UltraOne

IN VEHICLE SECURITY ULTIMATE FLEXIBILITY. Installation Supplement. ClassicOne & UltraOne 25) Ignition-Activated Anti-Carjacking Protection: Default OFF. 26) Door-Activated Anti-Carjacking Protection: Default OFF. 27) Open Door Warning Upon Arming: Default OFF. 28) PANIC Button Operates "Panic"

More information

Model PRO 9246CH Installation Manual

Model PRO 9246CH Installation Manual Model PRO 9246CH Installation Manual PRE-INSTALLATION NOTES: RF Programmable Features : Feature Selection 1 Flash 2 Flash 3 Flash Default 1st Do L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec. 2nd Accy Lock

More information

Model APS-20B Owner's Manual

Model APS-20B Owner's Manual Model APS-20B Owner's Manual 3 Button Vehicle Alarm System With Auxiliary Output FEATURES: 2 Three Button RF Transmitters Three Channel Code Learning Receiver Remote Panic In All Modes Built-In Parking

More information

SECURITY SYSTEM INSTALLATION MANUAL

SECURITY SYSTEM INSTALLATION MANUAL INSTALLATION MANUAL SECURITY SYSTEM BEFORE INSTALLING THE SYTEM DO read through this installation manual. DO NOT install the alarm brain in an engine compartment. The alarm may arm itself when power is

More information

RS-351-EDP. Installation Guide

RS-351-EDP. Installation Guide RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...

More information

CA 421 Installation Instructions

CA 421 Installation Instructions CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

*IMPORTANT INFORMATION:

*IMPORTANT INFORMATION: CS-2003DC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This system

More information

STARTER DISABLE/ KEYLESS ENTRY SYSTEM

STARTER DISABLE/ KEYLESS ENTRY SYSTEM I N S T A L L A T I O N M A N U A L STARTER DISABLE/ KEYLESS ENTRY SYSTEM BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM DO read through this installation manual. DO NOT install the control

More information