EVEN HEAT SMALL SPACES (G35308) Propane (G35309) Natural Gas

Transcription

1 DURILITY POWER PERFORMNCE EVEN HET barbecue SMLL SPCES SSEMLY MNUL (G35308) Propane (G35309) Natural Gas Limited 5-Year Warranty Read and save manual for future reference. ssemble your grill immediately. Missing or damaged parts should be claimed within 30 days of purchase. For product inquiries, parts, warranty and troubleshooting support, please call Manual Revision #: T

2 HEVY RTICLE NEEDS 2 TO LIFT THIS MNUL MUST REMIN WITH THE PRODUCT T LL TIMES To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at CUTION Sharp edges. Wear gloves when assembling your grill. CUTION Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook. INSTLLER OR SSEMLER/ CONSUMER This manual should be kept with the Q at all times. WRNING Failure to follow all of the Manufacturer s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death. Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting Instructions section of this manual. DNGER 1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department 2. Requires two people to complete the assembly process. 3. eware of sharp edges. WRNING 1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance. 2. n LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WRNING IN DIRECT SUN, ND IN OPERTION, YOUR Q S STINLESS STEEL ND PINTED STEEL PRTS CN ECOME VERY HOT. THIS RECUE IS FOR OUTDOOR USE ONLY CONTCT CLL CENTRE IF NY PRTS RE MISSING

3 HRDWRE PCK TOOLS NEEDED FOR SSEMLY #2 Phillips screwdriver (long and short) ¼ Slotted screwdriver (long and short) djustable wrench Pliers For correct hardware assembly, always position the lock washer between the screw and the flat washer. Screw Lock Washer Flat Washer No. Description Part Number Qty. 1 ¼ -20UNCX38 Screw ¼ -20UNCX16 Screw φ7 Lock Washer φ7 Washer /4-20UNC Nut NO.10-24UNCx13 Screw φ5 Lock Washer φ5 Washer ST4.2x10 Tapping Screw /4-20UNC Screw G U Pin Tool G Rubberized Washer G Caution: Sheet metal can cause injury. Wear gloves when installing the grill /4-20UNCx38 Screw X 8 1/4-20UNCx16 Screw X 14 φ7 Lock Washer X φ7 Washer X 22 1/4-20UNC Nut X 8 NO.10-24UNCX13 Screw X φ5 Lock Washer X 6 φ5 Washer X 6 ST4.2x10 Tapping Screw /4-20UNC Screw U Pin X 1 Rubberized Washer X8 EFORE SSEMLING THE RECUE, RED THESE INSTRUCTIONS CREFULLY. ssemble the barbecue on a flat, clean surface. Grill is heavy. You should have at least two people assemble the barbecue together. 1

4 Parts List (propane) for (G35308) Item No. Qty. Description Part No. 1 Top lid assembly G Thermometer G C 2 Screw for top lid G D 2 Lid bumper, front G E 2 Lid bumper, rear G urner box assembly G Even Heat burners G C 1 Carryover assembly G D 2 Even Heat heat distribution G plate E 2 Cooking grate G F 1 Warming rack G G 1 Match holder G C 1 Manifold assembly-lp G C 1 Regulator G CC1 1 Electronic ignition assembly G CC2 1 Ignition battery cover G CC3 1 Instastart ignition button G CD 2 Electrode set, main burner G CE 2 Control knob G CF 1 Control panel G CG 1 Front brace G CH 1 Quick Clean grease tray G CI 1 Quick Clean grease cup G CJ 1 Upper back panel G CK 1 Heat shield G CL 1 Right track G CM 1 Left track G CN 1 Door support rail G Item No. Qty. Description Part No. D 2 Support bracket, side shelf G D 2 Support bracket, side shelf G DC 2 Side shelf G E 1 Left side panel G E 1 Right side panel G EC 1 Door assembly G ED 1 Door handle G EE 1 ottom shelf-lp G EF 2 Locking castor G EG 2 Castor G EH 1 Door magnet assembly G501-00F2-02 F1 1 Hardware pack G F2 1 ssembly manual G353-M F3 1 Safe use and care manual G353-M F4 1 Tank Screw G

5 EXPLODED DIGRM (PROPNE) FOR (G35308) Extras Hardware Pack ssembly Manual Safety & Care Manual Tank Screw F1 F2 F3 F4 3

6 PRTS LIST (NTURL GS) FOR (G35309) Item No. Qty. Description Part No. 1 Top lid assembly G Thermometer G C 2 Screw for top lid G D 2 Lid bumper, front G E 2 Lid bumper, rear G urner box assembly G Even Heat burners G C 1 Carryover assembly G D 2 Even Heat heat distribution G plate E 2 Cooking grate G F 1 Warming rack G G 1 Match holder G C 1 Manifold assembly-ng G C 1 Natural Gas Hose G CC1 1 Electronic ignition assembly G CC2 1 Ignition battery cover G CC3 1 Instastart ignition button G CD 2 Electrode set, main burner G CE 2 Control knob G CF 1 Control panel G CG 1 Front brace G CH 1 Quick Clean grease tray G CI 1 Quick Clean grease cup G CJ 1 Upper back panel G CK 1 Heat shield G CL 1 Right track G CM 1 Left track G CN 1 Door support rail G Item No. Qty. Description Part No. D 2 Support bracket, side shelf G D 2 Support bracket, side shelf G DC 2 Side shelf G E 1 Left side panel G E 1 Right side panel G EC 1 Door assembly G ED 1 Door handle G EE 1 ottom shelf-ng G EF 2 Locking castor G EG 2 Castor G EH 1 Door magnet assembly G501-00F2-02 F1 1 Hardware pack G F2 1 ssembly manual G353-M F3 1 Safe use and care manual G353-M

7 EXPLODED DIGRM (natural gas) FOR (G35309) Extras Hardware Pack ssembly Manual Safety & Care Manual F1 F2 F3 5

8 SSEMLY INSTRUCTIONS 1 EF EG EE EF EG Separate the 2 different types of castors: 2 locking castors (EF) and 2 regular castors (EG). Note: Regular castors (EG) need to be assembled to the front of the bottom shelf (EE), and locking castors (EF) need to be assembled to the back of the bottom shelf (EE), as shown in figure. Upside down view EG ttach the regular castor (EG) to the front of the bottom shelf (EE), and use the Pin (#11) to secure and tighten (Figure ). Repeat for remaining 3 castors (EF & EG). 11 You will need: 611 Close up X 1 2 Ensure that the locking castors (EF) are firmly locked in the ON position before continuing. E ssemble the left side panel (E) and the right side panel (E), to the bottom shelf (EE). E You will need: EE X 6 X 6 X 6 Front view Close up 6

9 SSEMLY INSTRUCTIONS 3 E CG ttach the front brace (CG) to the left and right cart side panels (E & E). The top of the front brace (CG) can be identified by two clips located on the top left, and right side of this part, as shown in. EE E TIP: One person should align the left side, while the second person assembles the right side. ack view You will need: Close up 4 CK ssemble the Heat Shield (CK) to the left and right side panel (E & E). E You will need: E 69 ack view 7

10 SSEMLY INSTRUCTIONS 5 THIS STEP REQUIRES 3 PEOPLE. DO NOT TTEMPT LONE. EXTREMELY HEVY! a. Position the top lid assembly and burner box assembly ( & ) onto the cart assembly (C), as shown. C Front view 6 ttach the upper back panel (CJ) to both the left and right side panels (E & E). DO NOT tighten screws until all hardware has been positioned. You will need: E E CJ ack view 8

11 SSEMLY INSTRUCTIONS 7 ssemble the left and right tracks (CL and CM) for the Quick Clean grease tray (CH), as shown in figure, and C. CJ CM ack view CL CF Tip: oth the left and right tracks (CL and CM) should be inserted into the two clips located on the top of the front brace (CG), as shown in figure. CG Front view CJ ssemble the back of the left and right tracks (CL and CM) to the upper back panel (CJ), as shown in figure C C ack view X 2 X 2 X 2 9

12 SSEMLY INSTRUCTIONS 8 ssemble the door support rail (CN) to the left and right upper side panels (E and E), as shown. WRNING: This part may have sharp edges. Wear protective gloves when assembling. You will need: E CN E Front view 9 D Left and Right side shelf assembly a. ssemble the side shelf support bracket (D-front) and side shelf support bracket (D- back) to the right upper side panel of the burner box. D You will need: Front right side view b. ssemble the side shelf support bracket (D-back) and side shelf support bracket (D- front)to the left upper side panel of the burner box. D You will need: D Front left side view TIP: Ensure that the rubber side of the rubberized washer makes contact with the burner box. C Position of support brackets 10

13 SSEMLY INSTRUCTIONS 9 DC DC c. ssemble the left and right side shelves (DC) to the side shelf support brackets (D and D), as shown in figure D and E. D You will need: 610 CF D D Front view CF DC D E CG D Close up, right side shelf 11

14 SSEMLY INSTRUCTIONS 10 Electronic Ignition ssembly a. Remove the ignition battery cover (CC2) and the plastic nut from the electronic ignition box (CC1). CC1 E Right side panel, inside view CC2 b. Position the electronic ignition box (CC1) through the opening in the right side panel (E) and secure using the nut. c. Insert an battery into the battery compartment, as shown. Secure using the ignition button cover (CC2). - + Right side panel, outside view CC2 C CC3 Right side panel, inside view CC1 CD d. Insert the two Electrode set, main burner (CD) wires into the Electronic ignition assembly (CC1) as shown. NOTE: ll main burner electrode wire connection points are the same size. e. Insert the Instastart ignition button (CC3) wires into the Electronic ignition assembly (CC1), as shown in figure C. 12

15 SSEMLY INSTRUCTIONS 11 a. ssemble the door assembly (EC), to the bottom shelf (EE) by inserting the fixed pin (bottom of door) into the hole provided (figure ). E E EC EE Front view EC EE ottom of door CN EC b. ssemble the top of the door assembly (EC) to the door support rail (CN), by pressing in the door support pin and aligning with the hole located on the top right corner of the door. Tip: Use a paint scraper to press-in the support pin. The support pin will lock into position when the door is assembled correctly. C Top of door 13

16 SSEMLY INSTRUCTIONS 12 a. Position the Quick Clean grease tray (CH) onto the right and left tracks (CL and CM), as shown. CM b. Position the Quick Clean grease cup (CI) in position under the under the Quick Clean grease tray (CH). CL CH CI ack view 13 D a. Position the Even Heat heat distribution plates (D) into the burner box () as shown. D D Close up, front view C Close up, back view F b. Place the cooking grates (E) into the burner box (), as shown in figure D. D E c. ssemble the warming rack (F) by inserting the two fixed pins into the two holes provided on the burner box back panel (), as shown. 14

17 SSEMLY INSTRUCTIONS 14 For propane model only For natural gas model, follow step 15. ttach the regulator (C) coupling nut to the propane cylinder valve. TTENTION: For your family s safety, do not attempt to light this Q until you have reviewed pages 4-7 of the Coleman Even Heat arbecues Safety and Care Manual. ll safety and leak tests MUST E PERFORMED Y THE END USER, prior to lighting this Q. C 15

18 SSEMLY INSTRUCTIONS 15 For natural gas model only ttach the natural gas hose (C), as shown. C TTENTION: In order to complete installation of your Natural Gas Q a 1/2 or 3/8 adapter may be required to connect your Q s Natural gas hose to your home gas supply. Contact your natural gas supplier to purchase the necessary part. TTENTION: For your family s safety, do not attempt to light this Q until you have reviewed pages 4-7 of the Coleman Even Heat arbecues Safety and Care Manual. ll safety and leak tests MUST E PERFORMED Y THE END USER, prior to lighting this Q. WRNING: For all new, at home, natural gas connections please contact a certified gas technician to install your natural gas barbecue. C Quick Connector Natural Gas Home Supply 16

19 DDITIONL WRNINGS You have now completed the ssembly of your COLEMN EVEN HET RECUE. NEXT STEPS: 1. Position your RECUE 2. Read SFE USE CRE MNUL 3. Perform Grill Safety Check-list WRNING: FOR YOUR FMILIES SFETY, DO NOT TTEMPT TO LIGHT THIS Q UNTIL YOU HVE REVIEWED PGES 4-7 OF THE COLEMN SFE USE ND CRE MNUL. LL SFETY ND LEK TESTS MUST E PERFORMED Y THE END USER, PRIOR TO LIGHTING THIS Q. WRNING HOT SURFCES:!!! POSITION YOUR RECUE lways confirm that this arbecue is not positioned under a combustible object (e.g., an awning or umbrella) or in a covered area (e.g., porch or gazebo) before lighting it, to prevent a possible fire. lways confirm that this arbecue is not positioned under the overhang of a house, a garage or other structure before lighting it. n overhang will serve to deflect flare-ups and radiate heat into the structure itself, which could result in a fire. lways confirm that this arbecue is positioned more than 36 (91.4cm) away from any combustible materials or surfaces before lighting it, and that no gasoline or other volatile substances are stored in the vicinity of this arbecue. The temperature of a grease fire or of the radiated heat might otherwise be sufficient to ignite nearby combustibles or volatile substances. Do not position near windows, siding, or fencing. lways locate the arbecue where there will be ample combustion and ventilation air, but never position it in the direct path of a strong wind.

20 Join the conversation facebook.com/colemangrills twitter.com/colemangrills Manufactured by Winners Products Engineering Ltd. Coleman, and are registered trademarks of The Coleman Company, Inc. used under license The Coleman Company, Inc.