FERROXCUBE DATA SHEET. E16/8/5 E cores and accessories. Supersedes data of September Sep 01

Transcription

1 FERROXCUBE DATA SHEET Supersedes data of September Sep 1

2 CORE SETS Effective core parameters SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 1.87 mm 1 V e effective volume 75 mm 3 I e effective length 37.6 mm A e effective area 2.1 mm 2 A min minimum area 19.3 mm 2 m mass of core half 2. g handbook, halfpage R CBW9 Dimensions in mm. Fig.1 core half. Core halves A L measured in combination with a non-gapped core half, clamping force for A L measurements, 2 ±1 N. GRADE A L (nh) µ e AIR GAP (µm) 3C9 63 ±5% C9-A63 1 ±8% C9-A1 16 ±8% C9-A16 25 ±15% C9-A ±15% C9-A ±25% 164-3C9 3C92 84 ±25% 125-3C92 3C94 11 ±25% 164-3C94 3C96 98 ±25% 146-3C96 3F3 63 ±5% F3-A63 1 ±8% F3-A1 16 ±8% F3-A16 25 ±15% F3-A ±15% F3-A ±25% 146-3F3 3F35 76 ±25% 113-3F35 28 Sep 1 327

3 Core halves of high permeability grades Clamping force for A L measurements, 2 ±1 N. GRADE A L (nh) Properties of core sets under power conditions Properties of core sets under power conditions (continued) µ e AIR GAP (µm) 3E27 22 ±25% 33-3E27 B (mt) at CORE LOSS (W) at GRADE H=25A/m; f=25khz; f = 1 khz; f = 1 khz; f = 4 khz; f = 25 khz; Bˆ =2mT; Bˆ = 1 mt; Bˆ =2mT; Bˆ =5mT; T = 1 C T = 1 C T=1 C T = 1 C T = 1 C 3C C C C F F35 3 B (mt) at CORE LOSS (W) at GRADE H=25A/m; f=5khz; f = 5 khz; f=1mhz; f=3mhz; f = 25 khz; Bˆ =5mT; Bˆ =1mT; Bˆ =3mT; Bˆ =1mT; T = 1 C T=1 C T = 1 C T = 1 C T=1 C 3C9 32 3C C C F F Sep 1 328

4 COIL FORMER General data for 6-pins coil former PARAMETER Coil former material Pin material Maximum operating temperature Resistance to soldering heat Solderability SPECIFICATION polyamide (PA6.6), glass reinforced, flame retardant in accordance with UL 94V- ; UL file number E41871(M) copper-tin alloy (CuSn), tin (Sn) plated 13 C, IEC 685, class B IEC , Part 2, Test Tb, method 1B, 35 C, 3.5 s IEC , Part 2, Test Ta, method 1, 235 C, 2 s handbook, full pagewidth 9.4 min ± max max ± ± max max CBW1 Dimensions in mm. Fig.2 coil former; 6-pins. Winding data and area product for 6-pins coil former NUMBER OF SECTIONS (mm 2 ) MINIMUM WIDTH AVERAGE LENGTH OF TURN PRODUCT Ae x Aw (mm 4 ) CPH--1S-6P-Z 28 Sep 1 329

5 COIL FORMER General data for 9-pins coil former PARAMETER Coil former material Pin material Maximum operating temperature Resistance to soldering heat Solderability SPECIFICATION phenolformaldehyde (PF), glass reinforced, flame retardant in accordance with UL 94V- ; UL file number E41429 (M) copper-clad steel, tin (Sn) plated 18 C, IEC 685, class H IEC , Part 2, Test Tb, method 1B, 35 C, 3.5 s IEC , Part 2, Test Ta, method 1, 235 C, 2 s 11.1 ± ± ± ± ± ± ±.15 4 ±.3.64 ± ± ±.3.64 ±.5 17 ± ± MFW47 Dimensions in mm. Fig.3 coil former; 9-pins. Winding data and area product for 9-pins coil former; note 1 NUMBER OF SECTIONS (mm 2 ) MINIMUM WIDTH AVERAGE LENGTH OF TURN PRODUCT Ae x Aw (mm 4 ) CSH--1S-9P Note 1. This coil former is optimized for the use of triple-isolated wire. This wire is approved for safety isolation without the usual creepage distance. 28 Sep 1 33

6 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification PRODUCT STATUS Development DEFINITIONS This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype Design-in Preferred Support These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 28 Sep 1 331