3M Three-Wall and Four-Wall Headers. Series 3XXX
|
|
- Edith Perry
- 6 years ago
- Views:
Transcription
1 1 of 7 M Three-Wall and Four-Wall Headers Series XXX Product Released:
2 of 7 Table of Contents Section Page 1. Scope M Customer Documents Performance and Test Descriptions... Requirements Overview Test Results Summary 6. Test Sequences 7. Figures Agency Listings 6 Important Notice 7 Steven A. Neu: Approved: Sandra J. Stuckert: Approved Jim W. Wessman: Approved
3 of 7 1. Scope This document summarizes test methods, test conditions and product performance requirements for the M Three- Wall and Four-Wall Headers. Listings of materials, finishes, test conditions, and test standards are included in this specification. In the event of conflict between this specification and any documents listed below, the listed documentation supersedes this specification.. M Customer Documents E TS-0771, Technical Data Sheet for XXX Series Three-Wall Header M TS-077, Technical Data Sheet for XXX Series Four-Wall Header E TS-, Technical Data Sheet for DXXX Series Four-Wall Header Instructions for Polarzing Key 18. Performance and Test Description Unless otherwise specified, all tests shall be mated to,.100 pitch Wiremount Sockets with 6 cable at ambient environmental conditions per EIA-6. Unless otherwise specified, all values and limits are typical of those obtained by qualification testing of the subject product. All specifications are subject to revision and change without notice from M.. Requirements Overview.1 Ratings Dielectric Withstanding Voltage: 1000 V Sea Level Temperature: - C to +10 C Insulation Resistance: >1 x10 9 Ω at 00 V DC Current: ( EIA method, 0 C maximum temperature rise. ) 1.7 Amperes, All contacts powered.00 Amperes, 6 contacts powered.00 Amperes, 1 contact powered. Materials Header Insulation: Glass Filled PBT Glass Filled PCT, High Temperature Option Pin Contact: Copper Alloy. Finishes Plating: TS-0771, TS-077 Nickel: 0-10 µ inches, ASTM B689-97, SAE AMS-QQ-N-90 Gold: 0 µ inches, MIL-G-0 Type II, Grade C, ASTM B88-01 Sn: µ inches Matte Tin or µ inches Tin-Lead TS- Nickel: 0-10 µ inches, ASTM B689-97, SAE AMS-QQ-N-90 Gold: 10 µ inches, MIL-G-0 Type II, Grade C, ASTM B88-01 Sn: 0-10 µ inches MatteTin
4 of 7. Regulatory Compliance See the Regulatory Information Appendix (RIA) in the RoHS compliance section of for compliance information. See customer drawings for regulatory specifics on each connector..0 Test Results Summary.1 Environmental Environmental Durability (0µ" Au) 0 Insertions/Withdrawals EIA-6-09B Durability (10µ" Au) 10 Insertions/Withdrawals EIA-6-09B Salt Spray No physical abnormalitities after test EIA-6-6A Thermal Shock No physical abnormalitities after test EIA-6-B Temperature Life No physical abnormalitities after test EIA-6-17A (Thermal Aging) Humidity Max. ΔR: <10 mω EIA-6-1A. Mechanical Mechanical Vibration Mechanical Shock Contact Retention No physical abnormalitities after test No electrical discontinuity > 1 μ sec No physical abnormalitities after test No electrical discontinuity > 1 μ sec. lb. min EIA-6-8A Test Condition V Table II A EIA-6-7A EIA-6-9A. Electrical Electrical Low Level Contact Resistance Dielectric Withstanding Voltage Max. ΔR: <10 mω EIA-6-A 1000 V Sea Level EIA-6-0A Insulation Resistance 1 x V dc EIA-6-1A Current Rating EIA-6-70A, Method, 1.7 Amp, All Lines Powered 0 C Temperature Rise Limit. M UB.00 Amp, 6* Lines Powered.00 Amp, 1 Line Powered header mated to board mount socket connector. *Lines are adjacent in x configuration. Physical Physical Visual No defects such as deformation, blister, EIA-6-18A damage, crack, etc. Nickel Underplating Thickness Gold Thickness 0-10 μ" 0 μ" EIA-6-8, C Average of random 10 μ" measurements from any Matte Tin Thickness 00-00μ" lots 60:0 Tin/Lead Thickness μ" Solderability >9% Coverage of solderable area EIA Test Sequence 6.1 Sequenced Tests Test Visual Low Level Connection Resistance (LLCR) Vibration Physical Shock Durability (with Environmental) Temperature Life (Thermal Aging) Humidity Thermal Shock Salt Spray TEST FLOW Sequence Numbers for Test Group A B C D 1 1 1,,,7 1,,,6,,6 6
5 of 7 6. Independent Tests 1. Plating Thicknesses. Header Solderability. Header Pin Retention. Dielectric Withstanding Voltage. Current Rating 6. Insulation Resistance 7.0 Figures 7.1 Temperature vs. Current Maximum Current (Amp) M Three-Wall and Four-Wall Headers Temperature vs. Current Derating Curve All Contacts Powered 0 C T-Rise Limit- Derated (1.7A) 0 C T-Rise Limit- Derated (1.7A) Max. Operating Temperature Limit (10 C) 0. 0 Max. Operating Temperature Limit (10 C) Ambient Temperature ( C) Base Curve Derated 0% 0C T-Rise Derated 9 M Three-Wall and Four-Wall Headers Temperature vs. Current Derating Curve 6 Contacts Powered 8 Maximum Current (Amp) C T-Rise Limit- Derated (.00A) Base Curve Derated 0% 0C T-Rise Derated 1 Max. Operating Temperature Limit (10 C) Ambient Temperature ( C)
6 6 of 7 Maximum Current (Amp) M Three-Wall and Four-Wall Headers Temperature vs. Current Derating Curve 1 Contact Powered 0 C T-Rise Limit- Derated (.00A) Max. Operating Temperature Limit (10 C) Ambient Temperature ( C) Base Curve Derated 0% 0C T-Rise Derated 8. Agency Listings 8.1 Underwriters Laboratories (UL) Agency UL CUL File No. E68080 E68080
7 7 of 7 M is a trademark of M Company. Important Notice All statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M 010. All rights reserved.
3M Connector System 0.050" x 0.100" Pitch. 3M Tripolarized Wiremount Socket - Series 820 3M 4-Wall, Tripolarized Header - Series 810
1 of 9 3M Connector System 0.050" x 0.100" Pitch 3M Tripolarized Wiremount Socket - Series 820 3M 4-Wall, Tripolarized Header - Series 810 Product Specification 78-5110-0074-0 Released: 10-1-10 2 of 9
More information3M CP2 Press-Fit Headers and Sockets, 2 mm
1 of 7 3M CP2 Press-Fit Headers and Sockets, 2 mm A-Style CP2 Connectors CP2-SA110-G1-KR Right Angle Socket Connectors mated to CP2-HA110-GA1-KR Header Connectors 78-5102-0083-1 Revised Date: February
More informationPRODUCT SPECIFICATION
of 3 C Section : For the 200222, 2002323, 2002444, 20025, 200252, 200252, 20026, 200262, 200262, 20028, 200283, 200284, 2002822, 2002824, 200283, 2002832, 2002833, 2002834 and 2002835 series parts..0 GENERAL
More information3M Pleated Foil I/O Cable Assemblies MDR Series
Mates with standard 3M MDR Boardmount Headers Pleated copper foil provides a 360 degree shield Overmolded Assemblies Available in 68, 80 and 100 Positions Molded-in strain relief Can utilize either #4-40
More informationCable Ties. Data Sheet
Cable Ties Data Sheet Product Description 3M Cable Ties are molded from 6/6 Nylon and are available in a variety of sizes, styles and colors including weather resistant black for outdoor use. Agency Listings
More information3M Textool Test and Burn-In Sockets for 1.0 mm Area Array Packages Including Ball Grid Array and Land Grid Array
3M Textool Test and Burn-In Sockets for 1.0 mm Area Array Packages Including Ball Grid Array and Land Grid Array 1.0 mm Pitch Socket Platforms Socket Max. Package Maximum Max. Pin Lid Series Product Number
More information3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide
3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide Installing Tall Skirt on SVC and SVE cabinets Instructions July 2016 78-0015-3067-0 2 July 2016 78-0015-3067-0 Contents 1. General
More informationData Sheet July For RoHS information, please visit
Data Sheet July 2017 3M Cable Ties are molded from 6/6 nylon and are available in a variety of sizes and styles, including weather resistant black for outdoor use. Agency Approvals & Self Certifications
More information3M Locator Plate
3M Locator Plate 3443-113 Instructions for the Assembly of 3M Tripolarized Wiremount Sockets 1.0 General The 3M Locator Plate 3443-113 was designed to aid in the assembly of the 3M Mini Socket Connector.50
More informationSPECIFICATION AND PERFORMANCE TABLE OF CONTENT. 1. Scope Reference Documents Material and Components... 2
TABLE OF CONTENT 1. Scope... 2 2. Reference Documents.. 2 3. Material and Components...... 2 4. Design and Construction..... 2 5. Rating.. 2 6. Performance and Test Descriptions. 2 7. Test Requirements
More information3M Locator Plate
M Locator Plate 44-94 Instructions for the assembly of M Socket Connectors,.100" x.100" and.100" x.200" 1.0 General M Manual and Pneumatic Assembly Presses and accessory assembly equipment are recommended
More information3M Mechanical Shearbolt Connectors, QCI Series
M Mechanical Shearbolt Connectors, QCI Series Data Sheet November 2011 Description Connector Contents M Mechanical Shearbolt Connectors, QCI Series are designed to cover a wide range of conductor sizes
More informationPRODUCT SPECIFICATION
1.0mm Pitch ZIF FPC Page 1 Top Entry Side Entry 1.0mm Pitch ZIF FPC Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for 1.0mm Pitch ZIF FPC Connector 2.0 APPLICABLE
More informationPRODUCT SPECIFICATION
MultiCat TM In-line Power Connector System WIRE-TO-WIRE AND WIRE-TO-BOARD MALE CRIMP CONTACT (201845-00X0) FEMALE CRIMP CONTACT (201846-00X0) PLUG HOUSING (201840-00XX) RECEPTACLE HOUSING (201841-00XX)
More informationSEP 2016 Rev D2
Product Specification 108-2112 28 SEP 2016 Rev D2 VAL-U-LOK* Connectors 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for VAL-U-LOK* Connectors. 1.2. Qualification
More information3M Mini D Ribbon (MDR) Cable Assembly.050 High Speed Video Data Transmission System, 50 Position 14X50-SZWB-XXX-0NC
(MDR) Assembly Supports LVDS Channel Link signaling 20 shielded pairs (100 ohm) +4 drains for high bandwidth applications High density 50 position MDR with rugged ribbon type contact 3 Unshielded Twisted
More informationSerial Attached SCSI (SAS) Connector
Product 108-51053 Specification DR: Stanley Huang 24 Oct 2013 Rev G APVD: Vincent Peng Serial Attached SCSI (SAS) Connector 1.0 SCOPE This specification covers the requirements for product performance,
More informationProduct Specification AMP Mini CT DC Drawer Connector, 1.5 mm Pitch Lead Free Version
Product Specification 108-60026 MP Mini CT DC Drawer Connector, 1.5 mm Pitch Lead Free Version 1. 1.1 Scope: Contents: This specification covers the requirements for product performance, test methods and
More informationSeries 80 Mighty Mouse Technical Reference Complete Product Specification
Summary Performance Specifications Current Rating (Maximum): Size #23 Contact: 5 A., Size #20 contact: 7.5 A., Size #16 contact: 13 A., Size #12 contact: 23 A. Test Voltage (Dielectric Withstanding Voltage)
More informationJun 20,2014 Rev A
Product Specification 108-115067 Jun 20,2014 Rev A DDR4 DIMM Through-hole Memory Socket 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity
More information3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series
3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series Data Sheet 1. Product Description 3M Cold Shrink Termination Kit QT-III 7672-S-8 Series contains one silicone rubber termination
More informationProduct Specification Rev A
Product Specification 108-6116 1. Scope :.5 Signal DBL Lock Connector 18P 1.1 Contents This specification covers the requirements for product performance, test methods and quality assurance provisions
More information3M Ladder Kit 3M710/MS 2 -TMK-LK
3M Ladder Kit 3M710/MS 2 -TMK-LK Instructions 1.0 Summary The 3M Ladder Kit 3M710/MS2-TMK-LK is intended for mounting a communication line splicing system to a fiberglass extension ladder. 2.0 Kit Contents
More informationPRODUCT SPECIFICATION
288 Ckt Vertical Press Fit DDR4 DIMM 2.4mm Seating Plane 1.0 SCOPE This Product Specification covers the 0.85 mm centerline gold plated DDR4 DIMM edge card connector for 1.40 +/- 0.10 thick memory modules.
More information3M Cold Shrink QS-III Inline Splice Kits 15 kv 5513A, 5514A, 5515A and 5516A
3M Cold Shrink QS-III Inline Splice Kits 15 kv Data Sheet June 2014! CAUTION Working around energized high-voltage systems may cause serious injury or death. Installation should be performed by personnel
More informationJun06 Rev D
Product Specification High Speed Serial Data 2 Connector 108-1965 27Jun06 Rev D 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics High
More informationSPECIFICATION 宏致電子股份有限公司 桃園縣中壢市東園路 13 號. No.13, Dongyuan Rd., Jhongli City, Taoyuan County 320, Taiwan (R.O.C.)
SPECIFICATION 宏致電子股份有限公司 桃園縣中壢市東園路 13 號 No.13, Dongyuan Rd., Jhongli City, Taoyuan County 320, Taiwan (R.O.C.) TEL: +886-3-463-2808 FAX: +886-3-463-1800 SPEC. NO.: PS - 87151-XXX9 REVISION: D PRODUCT NAME:
More informationAug07 Rev A All Paragraphs Revised
Qualification Test Report Universal MATE-N-LOK* Connector 110-213 28Aug07 Rev A All Paragraphs Revised 1. INTRODUCTION 1.1. Purpose 1.2. Scope Testing was performed on Universal MATE-N-LOK* connectors
More information3M Cold Shrink 3-Conductor Inline Splice Kits QS-III 5786A- MT, 5787A-MT and 5788A-MT 25/28 kv for use with Armored and Non- Armored 3/C Cable
3M Cold Shrink 3-Conductor Inline Splice Kits QS-III 5786A- MT, 5787A-MT and 5788A-MT 25/28 kv for use with Armored and Non- Armored 3/C Cable Data Sheet September 2010 Description 3M Cold Shrink 3-Conductor
More information3M Cold Shrink 1/C Transition Splice Kit QS-III, 5510A-1T-PILC Series
3M Cold Shrink 1/C Transition Splice Kit QS-III, 5510A-1T-PILC Series Data Sheet March 2011 Description 3M Cold Shrink 1/C Transition Splice Kits QS-III, 5510A-1T-PILC Series (which includes 5513A-1T-PILC,
More informationGM Specification Annual Test Data
GM Specification Annual Test Data GM Specification Annual Test Data Technical Bulletin The 3M IATD Quality Laboratory tested the following tapes to the Automotive Specification. The results of the testing
More informationGM Specification Annual Test Data
GM Specification Annual Test Data GM Specification Annual Test Data Technical Bulletin The 3M IATD Quality Laboratory tested the following tapes to the Automotive Specification. The results of the testing
More informationMEZALOK* Stacking Connector System
Product Specification 108-2411 25 FEB 16 Rev D MEZALOK* Stacking Connector System 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the MEZALOK* Stacking Connector
More informationPRODUCT SPECIFICATION
MICRO-FIT BMI FLOATING CONNECTOR SYSTEM 1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) connector system terminated with 20 to 30 AWG wire using crimp technology
More information3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TS (RW)
3M Cold Shrink Skirted Termination Kit QT-III 7672-S-8-TS (RW) for Tape Shielded Cable Instructions Class 1 Termination IEC 60840 72,5 kv 69 kv Class 325 kv BIL CAUTION Working around energized systems
More informationMay2015 Rev A
Product Specification 108-60104 15May2015 Rev A ANGLED ENTRY JACK FOR CATEGORY 6 APPLICATIONS 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity
More information3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series
3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series For 3-Conductor Copper Tape Shield Cables without Ground Wires Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working
More information3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8(S)-JCN
3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8(S)-JCN For Jacketed Concentric Neutral (JCN) Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350 kv BIL IEC 60840 72,5
More informationHIGH SPEED MEZZANINE PRODUCT SPECIFICATION
OARD TO OARD CONNECTOR 75005 Receptacle Assembly 75003 Plug Assembly Table of Contents 1.0 Scope 2.0 Product Description 3.0 Applicable Documents and Specifications 4.0 Ratings 5.0 Performance 5.1 Qualification
More informationQSFP Copper Module Direct Attach Cable Assembly &Cage
Qualification Test Report 501-60067 12Mar. 2012 Rev. 1 QSFP Copper Module Direct Attach Cable Assembly& Qualification Test Report QSFP Copper Module Direct Attach Cable Assembly & Tyco Electronics. (Shanghai)
More informationK SERIES PUSH ON & BULLET TERMINALS
Industrial products we wholesale, you distribute K SERIES PUSH ON & BULLET TERMINALS NYLON INSULATED PUSH ON TERMINALS VINYL INSULATED PIGGY BACK PUSH ON TERMINALS NYLON FULLY INSULATED BULLET TERMINALS
More information3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination
3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working around energized electrical systems may
More information3M Closure System 2-Type Cover (505)
3M Closure System 2-Type Cover (505) Installation Instructions May 2009 78-8140-1009-2-B Contents 1.0 3M Closure Kit 2-Type Contents...3 2.0 Cover Installation...4 3.0 Closure Re-entry...6 4.0 Accessories...9
More information3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW)
3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW) for Tape Over Wire and Wire Over Tape Shielded Cable Instructions Class 1 Termination IEC 60840 72,5 kv 69 kv Class 325
More information3M Cold Shrink QT-III Silicone Rubber Termination Kits 7640-T and 7650-T Series 5, 8, 15, 25/28 and 35 kv
3M Cold Shrink QT-III Silicone Rubber Termination Kits 7640-T and 7650-T Series 5, 8, 15, 25/28 and 35 kv Data Sheet September 2014 Description 3M Cold Shrink QT-III Silicone Rubber Termination Kits, 7640-T
More information3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-Tape/LC
3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-Tape/LC For Tape Shield or Longitudinally Corrugated (LC) Shielded Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350
More information3M Cold Shrink QT-III Silicone Rubber Termination
3M Cold Shrink QT-III Silicone Rubber Termination For Tape-Over-Wire (TOW) or Wire-Over-Tape (WOT) Shielded Cable 7673-S-8(S)-TOW/WOT Instructions IEEE Std. No. 48 Class 1 Termination 69 kv Class, 350
More informationAUG 16 Rev C2
Product Specification 23 AUG 16 Rev C2 025 Series Connector 1Row 1. SCOPE 1.1 Contents This specification covers the requirements for product performance, test methods and quality assurance provisions
More information3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-TOW/WOT
3M Cold Shrink QT-III Silicone Rubber Termination 7673-S-8-TOW/WOT For Tape-Over-Wire (TOW) or Wire-Over-Tape (WOT) Shielded Cable Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class, 350
More informationMotor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables)
Motor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables) Instructions Kit Contents 3 Lug Covers 3 Cold Shrink Terminations 12
More information3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit
3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit With High-K Stress Relief For 3-Conductor Copper Tape Shield Cables with or without Ground Wires 7600-T-3RJS Series Instructions
More information710 Splicing Rig. Instructions. January E
710 Splicing Rig Instructions January 2007 Table of Contents 1.0 General Statement...4 2.0 3M 710-UTK25A Splicing Rig and Field Maintenance Kit...4 3.0 Straight Splicing using the 3M 710 25-pair modules...6
More information3M Cable Ties Product Guide. Made in USA. & Plenum Rated
3M Cable Ties Product Guide Made in USA & Plenum Rated A new line of general use cable ties from 3M Made in USA These ties are made of high quality 6/6 nylon in the USA, which offers excellent availability
More informationProduct Specification QSL RF Connectors
Product Specification QSL RF Connectors 108-2324 04Feb09 Rev A 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics QSL RF Connectors which
More informationS505SCH 5 x 20 mm Time-delay, high I 2 t, axial lead, ceramic tube fuses
Technical Data 10401 5 x 20 mm Time-delay, high I 2 t, axial lead, ceramic tube fuses Pb HALOGEN HF FREE Applications Primary circuit protection: Power supplies LED lighting LED/LCD televisions Appliances
More informationSPECIFICATIONS, PACKAGING INFORMATION, AGENCY APPROVALS AND PART NUMBERING SYSTEMS FOR TABLE F2 FUSES
SPECIFICATIONS, PACKAGING INFORMATION, AGENCY APPROVALS AND PART NUMBERING SYSTEMS FOR TABLE F2 FUSES Table F1 Environmental Specifications for Table F2 Fuses Operating Temperature Mechanical Vibration
More informationPRODUCT SPECIFICATION
1 of 14 Table of Contents 1.0 Scope... 3 2.0 Product Description... 3 2.1. Direct Connect (wire to board application)... 3 2.2. Inline Applications (wire to wire application)... 3 2.3. Receptacle Assembly...
More informationSolidMatrix 1206 Fast Acting Surface Mount Fuses
SolidMatrix 206 Fast Acting Surface Mount Fuses Features: Multilayer monolithic structure with glass ceramic body and silver fusing element Silver termination with nickel and pure-tin solder plating, providing
More informationCold Shrink Silicone Rubber Termination QT-III 7672-S-8-JCN
3 Cold Shrink Silicone Rubber Termination QT-III 7672-S-8-JCN Instructions IEEE Std. No. 48-1996 Class 1 Termination 69 kv Class 350 kv BIL IEC 60840 72,5 kv Kit Contents: 1 Silicone Rubber Lug Seal Insulator
More informationBranch Splice QS-2001B
Branch Splice QS-2001B Data Sheet 1. Product Description The 3M Branch Splice QS-2001B molded rubber splice kits are designed to connect extruded dielectric power cables rated 15 kv. The basic kits handle
More informationAPPLICATION INFORMATION APPLICATION INFORMATION
RECOMMENDED BULKHEAD PANEL CUT-OUTS SCSI Fine Pitch Vertical PCB Mount NUMBER OF PANEL CUT-OUT DIMENSION TABLE POSITIONS B G H 26 31.2 (1.230) 29.8 (1.175) 27.6 (1.085) 40 40.1 (1.580) 38.7 (1.525) 36.5
More informationQS-III. 5513A, 5514A, 5515A and 5516A 15 kv Cold Shrink Inline Splice Kits. Data Sheet CAUTION. 1. Product Description. 2. Applications.
QS-III 5513A, 5514A, 5515A and 5516A 15 kv Cold Shrink Inline Splice Kits Data Sheet Tape Shield Wire Shield UniShield Kit Contents: 1 Cold Shrink Silicone Rubber Splice Body 1 Cold Shrink Adapter Tube
More information3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits
3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits With High-K Stress Relief For 3-Conductor Type G (Ground Wire), Copper Tape Shield, Armored Cables 7600-S-3G Series Instructions IEEE Std.
More informationModification Record of Product Specification
Modification Record of Product Specification No, DSP-14 1303 Product Name SRV Connector Systems Rev. No, Note Reason Place Date Engineer R0 Initial Release DEC 2.19.14 A.M. Page 1/17 PRODUCT SPECIFICATION
More informationSLiC Aerial Closures
3 SLiC Aerial Closures 1 The 3M SLiC Closure is a singlepiece aerial closure easily installed in construction or maintenance situations. The one piece construction permits complete splice access after
More informationSinglFuse SF-1206HIxxxM Series Features
E SinglFuse SF-1206HIxxxM Series Features n Single blow fuse for overcurrent protection n 3216 (EIA 1206) footprint n High inrush current withstand fuse n UL 248-14 listed n RoHS compliant* and halogen
More information305/315/355 SERIES CARD EDGE CONNECTOR.156" (3.96mm) Contact Spacing
305/315/355 SERIES CARD EDGE CONNECTOR.156" (3.96mm) Contact Spacing 305/315/355 SERIES ORDERING CODE Example Part Number 305-056 - 521-2 04 Series Total Number of Contacts Contact Code Insulator Style
More informationSurface Mount Multilayer Ceramic Chip Capacitors for High Reliability Applications
Surface Mount Multilayer Ceramic Chip Capacitors for High Reliability Applications ELECTRICAL SPECIFICATIONS FEATURES Manufactured with a combination of design, materials and tight process control to achieve
More informationSpecification Status: Released
PAGE NO.: 1 OF 7 Termination Material: Copper, Ni, Tin Fuse Element: Copper/Copper alloy Body Material: Fiberglass/Epoxy Operating Temperature -55 C to +125 C (with de-rating) Specification Status: Released
More informationCMC Hybrid Connectors Standard and Power Versions
CMC hybrid connectors and mating headers provide sealed, high-density, modular and cost-effective wire-to-board and wire-to-wire connection systems for heavy-duty powertrain and body-electronics applications
More informationQUALIFICATION TEST SUMMARY REPORT ESR Qualification Type Testing of Amphenol Corporation s 2M801 Series Connector
Page 1 of 13 QUALIFICATION TEST SUMMARY REPORT ESR-9389 Qualification Type Testing of Amphenol Corporation s Connector PREPARED BY: Patrick Cole Design Engineer AMPHENOL CORPORATION Aerospace Operation
More informationn For use in telecommunication circuit applications requiring low current protection with high surge tolerance
*RoHS COMPLIANT & **HALOGEN FREE 0.5 SinglFuse SF-3812TM-T Series Features n Replacement for Bourns Telefuse models B0500T, B1250T and B2000T n For use in telecommunication circuit applications requiring
More informationPRODUCT SPECIFICATION
ML-XT COMMERCIAL VEHICLE CONNECTOR SERIES 1.0 SCOPE This Product Specification relates to the ML-XT Commercial Vehicle, (CV), Power and/or Signal wire-to-wire connector system. This system consists of
More informationSMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
More informationCMC Hybrid Connectors Standard and Power Versions
CMC hybrid connectors and mating headers provide sealed, high-density, modular and cost-effective wire-to-board and wire-to-wire connection systems for heavy-duty powertrain and body-electronics applications
More informationCC06H High I 2 t Chip 0603 size fuses
Technical Data 4346 Supersedes June, 2014 Pb HALOGEN HF FREE Applications For secondary circuit protection in space constrained applications: LCD Backlight inverters Digital cameras DVD Players Bluetooth
More informationPRODUCT SPECIFICATION
PROUCT SPECIFICATION TABLE OF CONTENTS 1.0 SCOPE 2.0 PROUCT ESCRIPTION 3.0 APPLICABLE OCUMENTS AN SPECIFICATIONS 4.0 RATINGS 5.0 PERFORMANCE 5.1 ELECTRICAL PERFORMANCE 5.2 MECHANICAL PERFORMANCE 5.3 ENVIRONMENTAL
More informationNTC Thermistors, 2-Point Radial Leaded, Automotive Grade
NTC Thermistors, 2-Point Radial Leaded, Automotive Grade FEATURES High accuracy over a wide temperature range High stability over a long life Exceptional thermal shock withstanding performance AEC-Q200
More information3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions
3M No Polish Connector 8800-APC/AS SM SC/APC, Angle Splice, 250/900 µm Instructions February 2008 78-8140-1581-0 Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber
More information341/391 SERIES CARD EDGE CONNECTOR.100" (2.54mm) Contact Spacing
341/391 SERIES CARD EDGE CONNECTOR.100" (2.54mm) Contact Spacing 341/391 SERIES ORDERING CODE Example Part Number 341-062 - 520-2 02 Series Total Number of Contacts Contact Code Contact Rows Mounting Options
More informationNTC Thermistors, 2-Point Micro Chip Sensor Insulated Leads
NTC Thermistors, 2-Point Micro Chip Sensor Insulated Leads QUICK REFERENCE DATA PARAMETER VALUE UNIT Resistance value at 25 C 2.06K to 10K Ω Tolerance on R 25 -value ± 1.92; ± 2.19 % B 25/85 -value 3511
More informationNTC Thermistors, Mini Epoxy PVC Insulated Leads
NTC Thermistors, Mini Epoxy PVC Insulated Leads FEATURES High adhesive strength between the PVC wire and the encapsulating lacquer Accurate down to ± 0.3 C Small body of max. 3 mm for easy installation
More informationElectronic Materials Brochure
Electronic Materials Brochure TABLE OF CONTENTS 3 Introduction to Materials 4 ISODAMP C-8000 Materials 6 ISOLOSS SL Molding Materials - Thermosets 8 CONFOR EG Foams CONFOR SC Foams ISODAMP C-8000 MATERIALS
More information3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kits
3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kits With High Ampacity Ground Connection and High-K Stress Relief For Tape Shield, Wire-Over-Tape Shield and Longitudinally Corrugated (LC) Shield
More information3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm
3M No Polish LC Connector SM and MM, Flat Splice, 250/900 µm Instructions January 2009 78-8140-3696-4-A 3 Contents 1.0 Kit Contents... 3 2.0 3M No Polish LC Connector SM & MM 250/900 µm... 4 Safety Precautions
More information3M Cold Shrink Splice Kit QS-III 5536A
3M Cold Shrink Splice Kit QS-III 5536A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric
More informationSEK Solder board connectors
Solder board connectors Technical characteristics 6, 10, 14, 16, 20, 26, 30*, 34, 40, 50, 60, 64 Contact arrangement straight, angled Contact length 2.9 mm, 4.5 mm Approvals IEC 603-13 DIN EN 60 603-13
More information3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS
3M No Polish LC/APC Connector SM, Angle Splice, 250/900 µm 8830-APC/AS Instructions January 2009 78-8140-3691-5-A Contents 1.0 Summary...3 2.0 Connector Preparation...4 3.0 Fiber Preparation...4 4.0 Fiber
More informationSurface Mount > 0603L Series. Description. Features. Applications. Maximum Time To Trip Current (A) P d typ. (W)
0603L Series RoHS Description The 0603L Series PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features Agency Approvals
More informationDual Lock Reclosable Fasteners Roll Goods with Pressure Sensitive Adhesive
3 Dual Lock Reclosable Fasteners Roll Goods with Pressure Sensitive Adhesive Technical Data Sheet June 2012 General Description Applications 3M Dual Lock Reclosable Fasteners are positive-locking, blind
More informationPower Splitter/Combiner
Ultra-Small Ceramic Power Splitter/Combiner 2 Way-90 50Ω 2500 to 4500 MHz Maximum Ratings Operating Temperature -55 C to 100 C Storage Temperature -55 C to 100 C Power Input (as a splitter) 15W* max. *
More informationShaping. the future. Introducing. 3M Cubitron II Abrasive Belts NEW! 994F and 997F for high pressure applications
NEW! 3M Cubitron II Abrasive Belts Introducing 994F and 997F for high pressure applications Shaping the future Revolutionary shaped abrasive grain grinds cooler and dramatically faster. Now engineered
More informationTNC Series Series C TN 114
TNC Series TNC Series 114 TNC Interface Mating Dimensions (Per MIL-STD-348) TNC Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.440 11.17 B.314 7.98.315
More informationC&K 1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
More informationNTC Thermistors, Flex Foil Sensors
NTC Thermistors, Flex Foil Sensors QUICK REFERENCE DATA PARAMETER VALUE UNIT Resistance value at 25 C 10K, 47K Tolerance on R 25 -value ± 3 % B 25/85 -value 3960 K Tolerance on B 25/85 -value ± 1 % Operating
More informationDoor Edge Protection Film 36 inch
Door Edge Protection Film 36 inch Technical Data Sheet June, 2013 3M Part No.(s) PN 3M Part Descriptor(s) Door Edge Protection Film 36 inch Product Description 3M Door Protection Film is a super tough
More informationComposite Conductor 267-T16 ACCR. Deadend Strength Tests for 267-T16 ACCR
Composite Conductor 267-T16 ACCR Deadend Strength Tests for 267-T16 ACCR Principal Investigator: Dr. Colin McCullough Reviewed by: Dr. Herve Deve Date of Report: March 24, 2010 Deadend Strength Tests for
More informationProduct Specification
AFI Jack, Straight Orientation, Mixed Technology AFI Plug, Straight Orientation, Cable Terminated Other configurations available for: Vertical cable-to-board applications Floating Adaptor, Surface mount,
More informationTest Group Description. Total Number. Figure 1. Unless otherwise stated, the following environmental conditions prevailed during testing:
Qualification Test Report 26 November 12 Rev A1 SL Series Jacks, Category 6 1. INTRODUCTION 1.1. Purpose 1.2. Scope Testing was performed on AMP NETCONNECT* SL Series Category 6 Jacks to determine their
More informationSinglFuse SF-1206HVxxM Series Features
*RoHS COMPLIANT & **HALOGEN FREE V SinglFuse SF-1206HVxxM Series Features n Single blow fuse for overcurrent protection n 3216 (EIA 1206) footprint n High voltage rating applications n High current rating
More information