3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide

Transcription

1 3M Cross-Connect Cabinets 4220SVC and 4220SVE Tall Skirt Installation Guide Installing Tall Skirt on SVC and SVE cabinets Instructions July

2 2 July Contents 1. General 2. Kit contents 3. Tall skirt installation on back of 3M Cross Connect Cabinet SVC 4. Tall skirt installation on side of 3M Cross Connect Cabinet SVC 5. Tall skirt installation on back of 3M Cross Connect Cabinet SVE DSLAM 1 Right Side 6. Tall skirt installation on back of 3M Cross Connect Cabinet SVE DSLAM 2 Left Side 7. Tall skirt installation on side of 3M Cross Connect Cabinet SVE DSLAM 3 Left Side 8. Tall skirt installation on side of 3M Cross Connect Cabinet SVE DSLAM 4 Right Side 9. Bonding, mounting accessories and terminating cables 1.0 General 1.1 These instructions provide the information necessary for the installation of the tall skirt on the back and side of a 3M Cross Connect Cabinet 4220SV series. Use for stake, hand hole or pad mounted cabinets. One tall skirt needed for each DSLAM. Provides cable protection from ground/pad to bottom of DSLAM. Recommended DSLAM mounting order 1.2 Tools required for installation: UAE socket set Drill and drill bit Standard hand tools 13/64 Drill bit - for holes to attach skirt 1.3 Additional materials or accessories that may be needed for installation. Pallet mounting clips and hardware from cabinet Stakes Mounting ring Rear cable access cover (SVB/SVC) Rear cable access cover (SVE) Stabilizer (SVC) 2.0 Kit Contents 2.1 3M Cross-Connect Cabinet 4220SVC 1 tall skirt assembly 10 Self threading screws *Install tall skirt before mounting DSLAM.

3 July Tall skirt installation on a 3M Cross-Connect Cabinet 4220SVC 3.1 Remove the front panel from the skirt assembly. 3.3 Move the tall skirt away from the cabinet and drill the holes in the cabinet. Front panel 3.2 Place the tall skirt against the back of the cabinet and align the left side surface of the tall skirt flush with the left side surface of the cabinet. Transfer the tall skirt mounting holes to the cabinet back. 3.4 If you are using rear cable access cover, place it on the assembly prior to installing the tall skirt. 3.5 Place the tall skirt into position and fasten to back of the cabinet using the self-threading screws provided with the kit. 3.6 Remove knock outs if required and route DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs if required. 3.7 Seal the openings per you company practice.

4 4 July Power cable access hole (optional) Ground cable access hole (optional) 3.8 Attach the front panel to the tall skirt after the DSLAM is mounted. 4.3 Move the tall skirt away from the cabinet and drill the holes in the cabinet. 4.0 Tall skirt installation on side of 3M Cross-Connect Cabinet SVC 4.1 Remove the front panel from the skirt assembly. 4.2 Place the tall skirt against the left side of the cabinet. align the left side of the tall skirt with the front surface of the cabinet. Transfer the tall skirt mounting holes to the cabinet side and the side of the rear mounted tall skirt.

5 July Place the tall skirt into position and fasten to the side of the cabinet using the self-threading screws provided with the kit. 4.8 Attach the front panel to the tall skirt after the DSLAM is mounted. 4.5 Remove the knock out in the side of the rear tall skirt. *(Optional cable routing is through the large knock out in the side of the cabinet) Remove large knock out (if routing cable to the rear of the cabinet) 4.6 Route DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs on the side of the cabinet if required. 4.7 Seal the openings per your company practice. 5.0 Tall skirt installation on back of 3M Cross-Connect Cabinet SVE with DSLAM 1 right side 5.1 1st DSLAM Location: Remove the front panel from the skirt assembly. 5.2 Attach rear cable access cover (SVE) Rear cable access cover

6 6 July Place the tall skirt against the right rear of the cabinet. Align the right side of the tall skirt so it is flush with the right side of the cabinet. Transfer the tall skirt mounting holes to the cabinet back. 5.5 Place the tall skirt into position and fasten to the back of the cabinet using the self-threading screws provided with the kit. 5.4 Move the tall skirt away from the cabinet and drill the holes in the cabinet. 5.6 Remove knock outs if required and route DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs if required. 5.7 Seal the openings per your company practice.

7 July Attach the front panel to the tall skirt after the DSLAM is mounted. 6.3 Move the tall skirt away from the cabinet and drill the holes in the cabinet. 6.0 Tall skirt installation on back of 3M Cross-Connect Cabinet SVE with DSLAM 2 left side *Right side tall skirt must be installed prior to installing the left side tall skirt. 6.4 Place the tall skirt into position and fasten to the back of the cabinet using the self-threading screws provided with the kit. 6.5 Route DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs on the side of the cabinet if required. 6.1 Remove the front panel from the skirt assembly. 6.2 Place the tall skirt against the left rear side of the cabinet. Align the left side of the tall skirt flush with the left side of the cabinet. Transfer the tall skirt mounting holes to the cabinet back.

8 8 July Seal the openings per your company practice. 6.7 Attach the front panel to the tall skirt after the DSLAM is mounted. 7.2 Place the tall skirt against the left side of the cabinet. Align the left side of the tall skirt to the left side of the vents on the sidewall and to the right side of the large knock out on the side of the rear tall skirt. Transfer the tall skirt mounting holes to the cabinet sidewall and the left side of the rear mounted tall skirt. 7.0 Tall skirt installation on side of 3M Cross-Connect Cabinet SVE with DSLAM 3 left side *Left side rear tall skirt must be installed prior to installing the left side tall skirt. 7.3 Move the tall skirt away from the cabinet and drill the holes in the cabinet. 7.1 Remove the front panel from the skirt assembly. Vents 7.4 Place the tall skirt into position and fasten to the side of the cabinet and the side of the rear tall skirt using the self-threading screws provided with the kit. 7.5 Remove the large knock out in the side of the rear tall skirt and route the DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs on the side of the cabinet if required. *(Optional cable routing is through the large knock out in the side of the cabinet.)

9 July Place the tall skirt into position and fasten to the side of the cabinet using the self-threading screws provided with the kit. 7.7 Route DSLAM and fiber cables through the opening. Route the power and ground wire through the small knock outs on the side of the cabinet if required. Power cable access hole (optional) Ground cable access hole (optional) 7.8 Seal the openings per your company practice. 7.9 Attach the front panel to the tall skirt after the DSLAM is mounted. 8.0 Tall skirt installation on side of 3M Cross-Connect Cabinet SVE with DSLAM 4 right side 8.1 Mounting the fourth DSLAM on the right side of the cabinet is similar to mounting the DSLAM on the left side of the cabinet. *The rear right side DSLAM and tall skirt must be installed before the right side DSLAM and tall skirt. 9.0 Bonding, mounting accessories and terminating cables 9.1 See Instruction for information regarding bonding, mounting accessories and terminating cables per 3M MS 2 Splicing Modules, 3M 710 Modules, pedestal, pole mount, hand hole and pad mount cabinet practices.

10 3M and MS 2 are trademarks of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any direct, indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. Communication Markets Division 6801 River Place Blvd. Austin, TX Phone Web Please recycle. Printed in USA 3M All rights reserved