SPECIFICATIONS, PACKAGING INFORMATION, AGENCY APPROVALS AND PART NUMBERING SYSTEMS FOR TABLE F2 FUSES

Transcription

1 SPECIFICATIONS, PACKAGING INFORMATION, AGENCY APPROVALS AND PART NUMBERING SYSTEMS FOR TABLE F2 FUSES Table F1 Environmental Specifications for Table F2 Fuses Operating Temperature Mechanical Vibration Mechanical Shock Thermal Shock Resistance to Soldering Heat Solderability Moisture Resistance Salt Spray Storage Condition -55 C to +125 C (for the 03TSFV series the Operating Temperature is -55ºC to +90ºC) Withstands Hz at 30Gs when evaluated per Method 204 of MIL-STD-202 Withstands 1500Gs, 0.5 millisecond half-sine pulses when evaluated per Method 213 of MIL-STD-202 Withstands cycles from -65 C to +125 C when evaluated per Method 107 of MIL-STD-202 Withstands seconds at +2 C when evaluated per Method 210 of MIL-STD-202 Meets 95% minimum coverage requirement when evaluated per Method 208 of MIL-STD-202 Withstands 10 cycles when evaluated per Method 106 of MIL-STD-202 Withstands 48-hour exposure when evaluated per Method 101 of MIL-STD-202 #35 C/ 75% RH Table F2 Material Specifications for Table F2 Fuses Construction Body Material Termination Material Fuse Element Ceramic (1206/03/0402SFF, 1206/03SFS, 1206/03SFP, 1206SFH, 03SFV) Fiberglass/Epoxy (2410SFV, 1206SFV, 03TSFV) Silver, Nickel, Tin (1206/03/0402SFF, 1206/03SFS, 1206/03SFP, 1206SFH, 03SFV) Copper, Nickel, Tin(2410SFV, 1206SFV, 03TSFV) Silver (1206/03/0402SFF, 1206/03SFS, 1206/03SFP, 1206SFH, 03SFV) Copper/Copper Alloy (2410SFV, 1206SFV) Copper/Tin Alloy (03TSFV) Figure F1 Thermal Derating Current for Table F2 Fuses 1206/03/0402 Series 2410 Series RoHS Compliant, ELV Compliant HF Halogen Free Specifications subject to change without notice Littelfuse, Inc. 111

2 Figures F1 Thermal Derating Current for Table F2 Fuses (Cont d) 03TSFV Series 1206SFV Series Table F3 Electrical Specifications for Table F2 Fuses Insulation Resistance after Opening Current Carrying Capacity 20,000Ω rated voltage. Fuse clearing under low-voltage conditions may result in lower post- clearing insulation values. Under normal fault conditions Littelfuse fuses help provide sufficient insulation resistance for circuit protection. Notes: for 1206SFV series, the minimum DCR is 10,000Ω; for 03TSFV, the minimum DCR is Ω. Withstands % rated current at +25 C ambient for 4 hours when evaluated per MIL-PRF Table F4 Information for Table F2 Fuses Reel Quantity Carrier Reels per Outside Outside Shipment Size (pcs) Reel Diameter Reel Width Tape Size Tape Type Shipment Box Boxes per Overpack 0402 (5) 10, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to (18) 4, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to 10 03SFV (18) 6, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to 10 03TSFV (18) 8, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to (3216) 3, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Plastic 5 1 to SFV (3216) 3, mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Plastic 5 1 to SFV (6125) 2, mm white plastic 13.4 ± 0.5mm ± 0.10mm Plastic 4 1 to Specifications subject to change without notice Littelfuse, Inc. HF Halogen Free RoHS Compliant, ELV Compliant

3 Figure F2 Recommended Soldering Temperature Profile for Table F2 Fuses Tp Ramp Up tp Critical Zone T L to Tp T L Ts MAX t L Temperature Ts MIN ts Ramp Down Classification Reflow Profile 25 Reflow Profile t 25 C to Peak Profile Feature 1206/03/ Average Ramp Up Rate (Ts MAX to Tp) 3 C/second max 3 C/second max Temperature min (Ts MIN ) 150 C 150 C Temperature max (Ts MAX ) 200 C 200 C Time (ts MIN to ts MAX ) -1 seconds 40- seconds Time Maintained Above: Temperature (T L ) 217 C 200 C Time (t L ) -150 seconds seconds Peak/Classification Temperature (Tp) 2 C max 250 C max Time Within 5 C of Actual Peak Temperature Time (tp) seconds seconds From 25 C to ing (150 C) 8 minutes max 40- seconds Ramp Down Rate 4 C/seconds max Natural Cooling Time Classification Reflow Profile Profile Feature 03TSFV Average Ramp Up Rate 3 C/second max Temperature min 150 C Temperature max 1 C Time -120 seconds Peak/Classification temperature (Tp) 2 C Max Time of actual peak temperature Time 10 seconds Ramp down rate Natural Cooling 2 C 150 C ~ 1 C ~ 120 Seconds Min. 10 Seconds Natural Cooling Classification Reflow Profile Profile Feature 1206SFV Average Ramp Up Rate 3 C/second max Temperature min 150 C Temperature max 1 C Time -120 seconds Peak/Classification temperature (Tp) 245 C Max Time within 5 C of actual peak temperature Time seconds Ramp down rate Natural Cooling 245 ± 5 C 1 ± 5 C 150 ± 5 C Recommended Temperature Profile for Reflow Soldering Within 5 C of actual peak temperature ~ 120s 10 ~ 30s Recommended Conditions for Hand Soldering: 1. Using a hot air rework station that can reflow the solder on both terminations at the same time is strongly recommended; do not directly contact the chip termination with the tip of soldering iron. 2. ing: 150 C, s (min) Appropriate temperature (max) of soldering iron tip/soldering time (max): 2 C /10s or 350 C /3s. RoHS Compliant, ELV Compliant HF Halogen Free Specifications subject to change without notice Littelfuse, Inc. 113

4 Table F4 Information for Table F2 Fuses Dimension in in (mm) Mark 0402 (5) 03 (18) 1206 (3216) 03SFV(18) 2410SFV(6125) 1206SFV (3216) E ± ± ± ± ± ±0.004 (1.75 ± 0.10) (1.75 ± 0.10) (1.75 ± 0.10) (1.75 ± 0.10) (1.75 ± 0.10) (1.75 ± 0.10) F ± ± ± ± ± ± (3.50 ± 0.05) (3.50 ± 0.05) (3.50 ± 0.05) (3.50 ± 0.05) (5.50 ± 0.10) (3.50 ± 0.05) W ± ± ± ± ± ± (8.00 ± 0.10) (8.00 ± 0.10) (8.00 ± 0.10) (8.00 ± 0.10) (12.00 ± 0.10) (8.00 ± 0.10) P ± ± ± ± ± ± (2.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) P ± ± ± ± ± ± (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) (4.00 ± 0.10) P ± ± ± ± ± ± (2.00 ± 0.05) (2.00 ± 0.05) (2.00 ± 0.05) (2.00 ± 0.05) (2.00 ± 0.10) (2.00 ± 0.05) D ± ± ± ± ± /-0.00 ( /-0.00) ( /-0.00) ( /-0.00) ( /-0.00) ( /-0.00) /-0.00 D max 0.61 ± ± (1.00 max) (1.55 ± 0.10) 1.00 ± 0.05 t ± ± ± (0.23 ± 0.02) (0.25 ± 0.05) 0.22±0.05 A ± ± ± ± ± ±0.004 (0.67 ± 0.10) (0.98 ± 0.10) (1. ± 0.10) (0.98 ± 0.10) (2.85 ± 0.10) (2.05 ± 0.10) B ± ± ± ± ± ± (1.17 ± 0.10) (1. ± 0.10) (3.50 ± 0.10) (1. ± 0.10) (6.40 ± 0.10) (3.50 ± 0.10) K ± ± ± ± ± ± (0.63 ± 0.10) (0.95 ± 0.08) (1.27 ± 0.10) (0. ± 0.08) (2.35 ± 0.10) (1.30 ± 0.10) Figure F3 Component Tape Dimensions for Table F2 Fuses Paper Carrier Tape Specifications D 0 P 0 P 2 E 1 F W B 0 D 1 P 1 A 0 K 0 D 0 Plastic Carrier Tape Specifications P 0 P 2 t E 1 F W B 0 D 1 P 1 A 0 K Specifications subject to change without notice Littelfuse, Inc. HF Halogen Free RoHS Compliant, ELV Compliant

5 Figure F4 Reel Dimensions for Table F2 Fuses Dimension Description Dimension (mm) Mark 1206/03/ Hub Outer Diameter B.2 Reel Inside Width W Reel Outside Width W Tape Width 8 B W 2 Agency Approvals for Table F2 Fuses W 1 UL: Table F2 Fuses CQC: File # (for 2410SFV 0.5A, 1A, 2A) TUV: File # (for 2410SFV 0.5A, 0.63A, 1A, 1.25A, 2A) Part Numbering System for Fast-Acting, Slow-Blow And 03 Very Fast-Acting Chip Fuses 1206 SF F 400 F / = 24V DC FM = RoHS Compliant + Marked Part 050 = 0.50A 400 = 4A F = Fast Acting S = Slow Blow Size (1206, 03, 0402) Part Numbering System for High-Current-Rated Chip Fuses 1206 SF H F / = 24V DC FM = RoHS Compliant + Marked Part = 10A H = High Current Size (1206) RoHS Compliant, ELV Compliant HF Halogen Free Specifications subject to change without notice Littelfuse, Inc. 115

6 Part Numbering System for 1206/2410 Very Fast-Acting Fuses 2410 SF V 6.30 FM / = 125V DC M = Marked Part 6.30 = 6.30A V = Very Fast-Acting Size (2410) Part Numbering System for 03 Thin Film Very Fast-Acting Chip Fuses 03 T SF V FM / = 65V DC M = Marked Part = 1.0A V = Very Fast-Acting Series code: Thin Film Size (03) Notice: Littelfuse products are not designed for, and shall not be used for, any purpose (including, without limitation, automotive, military, aerospace, medical, life-saving, life-sustaining or nuclear facility applications, devices intended for surgical implant into the body, or any other application in which the failure or lack of desired operation of the product may result in personal injury, death, or property damage) other than those expressly set forth in applicable Littelfuse product documentation. Warranties granted by Littelfuse shall be deemed void for products used for any purpose not expressly set forth in applicable Littelfuse documentation. Littelfuse shall not be liable for any claims or damages arising out of products used in applications not expressly intended by Littelfuse as set forth in applicable Littelfuse documentation. The sale and use of Littelfuse products is subject to Littelfuse Terms and Conditions of Sale, unless otherwise agreed by Littelfuse. 116 Specifications subject to change without notice Littelfuse, Inc. HF Halogen Free RoHS Compliant, ELV Compliant