SIDACtor Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor Series - DO-214 E Description

Transcription

1 SIDACtor Series - DO-214 RoHS Pb e3 Description SIDACtor Series DO-214AA are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards. Features and Benefits Agency Approvals AGENCY AGENCY FILE NUMBER E13383 Low voltage overshoot Low on-state voltage Does not degrade surge capability after multiple surge events within limit. Fails short circuit when surged in excess of ratings Low capacitance 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-69A.1 Pinout Designation Applicable Global Standards Schematic Symbol Electrical Characteristics Not Applicable TIA-968-A TIA-968-B ITU K.2/21 Enhanced Level* ITU K.2/21 Basic Level GR 189 Inter-building* *A/B-rated parts require series resistance GR 189 Intra-building IEC YD/T 182 YD/T 993 YD/T 95 Part Number =2.2 Amps 2V bias V min V max ma min ma max A max V max pf min pf max P8SALRP P-8A P22SALRP P22A P3SALRP P3A P64SALRP P6A P72SALRP P7A P9SALRP P9A P11SALRP P11A P13SALRP P13A P15SALRP P15A P18SALRP P18A P21SALRP P21A P23SALRP P23A P26SALRP P26A P31SALRP P31A P35SALRP P35A P8SBLRP P-8B P22SBLRP P22B P3SBLRP P3B P64SBLRP P6B P72SBLRP P7B Table continues on next page.

2 Electrical Parameters (continued Part Number Surge Ratings =2.2 Amps 2V bias V min V max ma min ma max A max V max pf min pf max P9SBLRP P9B P11SBLRP P11B P13SBLRP P13B P15SBLRP P15B P18SBLRP P18B P21SBLRP P21B P23SBLRP P23B P26SBLRP P26B P31SBLRP P31B P35SBLRP P35B P45SBLRP P45B P8SCLRP P-8C P22SCLRP P22C P3SCLRP P3C P64SCLRP P6C P72SCLRP P7C P9SCLRP P9C P11SCLRP P11C P13SCLRP P13C P15SCLRP P15C P18SCLRP P18C P21SCLRP P21C P23SCLRP P23C P26SCLRP P26C P31SCLRP P31C P35SCLRP P35C P45SCLRP P45C P45SCLHLRP* P45L Notes: - Absolute maximum ratings measured at T A = 25ºC (unless otherwise noted. - Devices are bi-directional. - * P45SCLHLRP is low IH product Series I PP.2x31 1 2x1 1 8x2 1 1x16 1 1x56 1 5x32 1 1x36 1 1x1 1 5x31 1.5x7 2 2x x5 2 1x16 2 1x56 2 9x72 2 1x36 2 1x1 2 1x7 2 ITSM 5/6 Hz A min A min A min A min A min A min A min A min A min A min Amps/µs max A di/dt B C Notes: - Peak pulse current rating (I PP is repetitive and guaranteed for the life of the product. 1 Current waveform in µs - I PP ratings applicable over temperature range of -4ºC to +85ºC - The device must initially be in thermal equilibrium with -4 C < T 2 Voltage waveform in µs J < +15 C 3 For surge rating of P45SCLRP 1x7µs min=15a & typical=18a For surge rating of P45SCLHLRP 1x7µs min=15a

3 Thermal Considerations Package Symbol Parameter Value Unit DO-214AA T J Operating Junction Temperature Range -4 to +15 C T S Storage Temperature Range -65 to +15 C R JA Thermal Resistance: Junction to Ambient 9 C/W V-I Characteristics t r x t d Pulse Waveform -V I DRM +I -I +V IPP Peak Pulse Current %IPP 1 5 t r Peak Value Waveform = t r x t d t d t r = rise time to peak value t d = decay time to half value Half Value t Time (µs Normalized Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of Change % C Junction Temperature (T J C (T C = 25ºC Ratio of C Case Temperature (T C - ºC Additional Information Datasheet Resources Samples

4 Temperature SIDACtor Protection Thyristors Soldering Parameters Reflow Condition Pb-Free assembly (see Fig. 1 - Temperature Min (T s(min +15 C Pre Heat - Temperature Max (T s(max +2 C - Time (Min to Max (t s 6-18 secs. Average ramp up rate (Liquidus Temp (T L to peak 3 C/sec. Max. T S(max to T L - Ramp-up Rate 3 C/sec. Max. Reflow - Temperature (T L (Liquidus +217 C - Temperature (t L 6-15 secs. T P T L T S(max T S(min Preheat t S Figure 1 Ramp-up t P t L Critical Zone TL to TP Ramp-down Peak Temp (T P Time within 5 C of actual Peak Temp (t p Ramp-down Rate Time 25 C to Peak Temp (T P Do not exceed +26(+/-5 C 3 secs. Max. 6 C/sec. Max. 8 min. Max. +26 C 25 time to peak temperature (t 25ºC to peak Time Physical Specifications Environmental Specifications Lead Material Terminal Finish Body Material Copper Alloy 1% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V- High Temp Voltage Blocking Temp Cycling Biased Temp & Humidity 8% Rated (V AC Peak +125 C or +15 C, 54 or 18 hrs. MIL-STD-75 (Method 14 JEDEC, JESD22-A C to +15 C, 15 min. dwell, 1 up to 1 cycles. MIL-STD-75 (Method 151 EIA/JEDEC, JESD22-A14 52 V DC (+85 C 85%RH, 54 up to 18 hrs. EIA/ JEDEC, JESD22-A-11 High Temp Storage +15 C 18 hrs. MIL-STD-75 (Method 131 JEDEC, JESD22-A-11 Low Temp Storage -65 C, 18 hrs. Thermal Shock C to +1 C, 5 min. dwell, 1 sec. transfer, 1 cycles. MIL-STD-75 (Method 156 JEDEC, JESD22-A-16 Autoclave (Pressure Cooker Test +121 C, 1%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-12 Resistance to Solder Heat +26 C, 3 secs. MIL-STD-75 (Method 231 Moisture Sensitivity Level 85%RH, +85 C, 168 hrs., 3 reflow cycles (+26 C Peak. JEDEC-J-STD-2, Level 1 Part Numbering Part Marking P xxx S x LRP TYPE P = SIDACtor MEDIAN VOLTAGE REEL PACK RoHS COMPLIANT Pxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table Date Code CONSTRUCTION VARIABLE I PP RATING PACKAGE TYPE

5 Dimensions DO-214AA E B D K C Case Temperature Measurement Point H A F G.79 (2. Pad Outline.79 (2..11 (2.8 inch (millimeter Dimensions Inches Millimeters Min Max Min Max A B C D E F G H H- P45SCLHLRP K Packing Options Package Type Description Quantity Added Suffix Industry Standard S DO-214AA Tape & Reel Pack 25 RP EIA-481-D Tape and Reel Specification DO-214AA.157 ( ( ( (13. Arbor Hole Dia..315 ( ( DIA (1.5 Cover tape Dimensions are in inches (and millimeters..49 (12.4 Direction of Feed