Parts Manual. with Wiring Diagrams for domestic and standard export ovens PS570G SERIES GAS FIRED: Table of Contents: Page 2.

Transcription

1 A MIDDLEBY COMPANY PS570G SERIES GAS FIRED: SPL PF-BD July 14, 2006 Parts Manual with Wiring Diagrams for domestic and standard export ovens Serial # Code (Nine Digit Code) (for units produced prior to mid-july, 2006) First 4 digits - order of production Fifth digit - model specific Sixth and Seventh digit - month of production Eighth and Ninth digit - year of production Serial # Code (Ten Digit Code) (for units produced after mid-july, 2006) First 5 digits - order of production Sixth digit - model specific Seventh and Eighth digit - month of production Ninth and Tenth digit - year of production The PS570G replaced the PS570S. They are different! The PS570G requires a 208/240V, 1Phase Power Supply. Therefore the Control Circuit is 208/240V. A Modulating Gas Valve and Signal Amplifier Board were incorporated to reduce energy consumption and increase cooking efficiency. We call this our Energy Management System (EMS). Serial Tag Location PS570G Single Oven Shown Table of Contents: Page Middleby Marshall Inc. techsupport@middleby.com fax

2 Table of Contents Specification Sheet... 3 Key Parts... 7 View of Installation and Base Pad Kit(s)... 8 Parts for Installation and Base Kit(s)... 9 View of Oven Panels, End Plugs, Window and Legs...10 Parts for Oven Panels, End Plugs, Window and Legs...11 View of Front Control Area...12 Parts for Front Control Area...13 View of Gas Piping and Burner Assembly...14 Parts for Gas Piping and Burner Assembly...15 View of Rear Blower/Motor Assembly...16 Parts for Rear Blower/Motor Assembly...17 View of Rear Capacitor Area...18 Parts for Rear Capacitor Area...19 View of Single Belt Conveyor...20 Parts for Single Belt Conveyor...21 View of Split Belt Conveyor...22 Parts for Split Belt Conveyor...23 Standard Finger Configuration and Part Numbers...24 Wiring Diagram, G volt 50/60 Hz, 1 Phase, US, Rev E 2 of Ladder Diagram, G volt 50/60 Hz, 1 Phase, US, Rev E 1 of Wiring Diagram, G volt 50/60 Hz, 1 Phase, AU, Rev D...27 Wiring Diagram, G volt 50/60 Hz, 1 Phase, CAN, Rev C...28 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, DN Rev C...29 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, DUT Rev C...30 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, FR Rev C...31 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, GM Rev C...32 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, GK Rev C...33 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, IT Rev C...34 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, SP Rev C...35 Wiring Diagram, G230 volt 50 Hz, 1 Phase, CE, UK Rev F 2 of Ladder Diagram, G230 volt 50 Hz, 1 Phase, CE, UK Rev F 1 of

3 WHI.-4 Middleby" UIIJIMarshaU CONVEYORS OF EXCELLENCE A/A File No.: Item No.: Middleby Marshall PS Series Conveyor ovens bake both faster and at a lower temperature than other ovens. Patented vertical columns of hot air move heat aerodynamically instead of using high temperatures. The streams of hot air remove the boundary layers of oool heavy air which tend to insulate the product. This gives very rapid baking without burning.aii Middleby ovens are designed to cook a multitude of products including pizza, seafood, bagels, ethnic foods and more. Standard Features Impingement PLUS! low oven profile and dual air return Patented EMS Energy Management System reduces gas consumption and increases cooking efficiency 70"/1778mm-long cooking chamber 32"1813mm-wide, 106"/2692mm-long conveyor belt Stackable up to four units high Patented "Jet Sweep" impingement process that delivers constant heat to the chamber Microprocessor-oontrolled bake time/conveyor speed Customer-specific adjustable jet fingers that allow control of heat delivery Stainless steel front. sides and top Front-loading window with cool handle Reversible conveyor direction Optional Features Split belt- two 15"/381 mm belts with individually-adjustable speed settings Fom-, Conse!Ves Energy Middleby ovens provide very efficient heat transfer to product. Energy is conserved as air is recycled from heater to product, with minimum flue or vent loss. Clean ability PS570 ovens are designed for easy cleaning. Removable parts include: crumb pans, end panels, air fingers, and a folding oonveyor belt assembly. Easily SeiViced Control compartment is designed for quick and easy access. All electrical controls are door-mounted. Warranty All PS570 models have a one year parts and labor warranty. Oven start-up and demonstration are included at no additional charge (USA only). Ventilation For installation under a ventilation hood only. r111.4 Middlebr WI AI Marshal A MIDDLEBY COMPANY 140C Toastmaster Drrve Elg'r. '''II'OIS USA ~847)7;:. 1-33o::l Fax 1,8.17) 7~~-oo ts M.VNmiddlsbyoom

4 4

5 5

6 6

7 KEY PARTS 16, 17, ITEM PART NO. DESCRIPTION QUANTITY Kit, Digital Temperature Control 1 2 See Below Motor, Drive 1 or :1 (provided Standard) :1 (Hi-speed application) Brush, Drive Motor 1 or Kit, Conveyor Speed Controller 1 or 2 with Digital Display Assembly, Pickup, Drive Motor 1 or Kit, Thermocouple ( ) Fan, Cooling Motor, Blower, 1HP 2 9A Ignition Module, US Version 1 9B Ignition Module, CE Version 1 9C Ignition Module, Australian Version Burner Blower/Motor Assembly Valve, Modulating Gas, 1/2" Amplifier, Modulating Valve Air Switch, Rear Blower(s) Air Switch, Front, Burner/Blower Hi Limit Control Module Transformer, 240/120V Conveyor System Transformer, 240/24V, 25VA Transformer, 240/24V, 65VA 1 7

8 View of INSTALLATION KIT View of BASE PAD KIT 8

9 Parts for INSTALLATION KIT QTY. SGL. ITEM BELT P/N DESCRIPTION CONVEYOR REAR STOP, CONVEYOR END STOP, 29-1/ GAS PIPE NIPPLE, 1-1/4 X 6 Parts for BASE PAD KIT QTY. QTY. QTY. QTY. SGL. SGL./DBL. SGL./DBL. TRIPLE OVEN OVEN/W OVEN/W OVEN ITEM 19 LEGS 10 LEGS 15 LEGS P/N DESCRIPTION 1A LEG, 19 (483mm) (OPTIONAL) 1B LEG, 10 (254mm), No Longer Available 1C LEG, 15 (381mm) 1D LEG, 4 (102mm) (43158, set of 4) 3A CASTER, SWIVEL WITH 3/4 STUD 3B CASTER, SWIVEL WITH BRAKE PIPE CLAMP, 1-1/ NIPPLE, 1-1/4 DIA. X 3 L, NPT 7A PIPE, 1-1/4 DIA. X 6 L ELBOW, 90, 1-1/4 DIA GAS HOSE, 1-1/4 DIA. x 72 L LEG, 6 (152mm) ADJUATABLE WITH 3/4 STUD GAS PIPE, 1-1/4 DIA. x 54 L RESTRAINT CABLE, 60 (1524mm) EYE BOLT, BASE PAD TOP COVER (RIGHT OR LEFT) BASE PAD NOT SHOWN: SCREW, TEKS HD #10-32 x 1-1/ SCREW, TEKS HWH #2PT #10-16 x 3/ BOLT, HEX CAP 1/2-13 x 1-1/ FLAT WASHER, 1/ LOCK WASHER, 1/ EYE BOLT, WALL 9

10 View of PANELS, END PLUGS, WINDOW and LEGS 10

11 Parts for PANELS, END PLUGS, WINDOW and LEGS ITEM QTY. P/N DESCRIPTION ITEM QTY. P/N DESCRIPTION ASSY, UPPER END PLUG (INC. ITEMS 2-6) WINDOW GUARD WELDMENT, UPPER END PLUG PS BUMPER, WINDOW EYEBROW BASE PAD SCREW, AB HEX WSHR HD #10 X 3/ SCREW, THUMB WING NUT, 1/4-20 W/PLASTIC GRIP WINDOW ASSEMBLY WITH HATCH PLATE, END PLUG MOUNTING LATCH (INCLUDED IN ITEM 30) ASSY, LOWER END PLUG (INC. ITEMS 9-11) WELDMENT, LOWER END PLUG PS WING NUT, 1/4-20 W/PLASTIC GRIP PLATE, END PLUG MOUNTING ASSEMBLY, DRIVE MOTOR SHROUD ASSEMBLY, LEFT MOTOR SHROUD ASSEMBLY, RIGHT MOTOR SHROUD ASSEMBLY, REAR SHROUD (INC. ITEM 18 and 19) GRILL, COOLING FAN BUMPER TOP COVER GLASS, WINDOW, PRE-CUT (INCLUDED IN ITEM 30), 3-1/2 x SEALANT 34A LEG, SINGLE OVEN, 19 (483mm) 34B LEG, DOUBLE OVEN, 15 (381mm) 34C LEG, DOUBLE OVEN, 10 (254mm), NO LONGER AVAILABLE 34D LEG, 4 (43158, SET OF 4) BOLT, HEX CAP 1/2-13 X 1-1/4 - SINGLE & DOUBLE OVENS LOCKWASHER, 1/2 - SGL & DBL OVENS FLAT WASHER, 1/2 - SGL & DBL OVENS 38A CASTER, SWIVEL WITH 3/4 STUD - SINGLE, DOUBLE, & TRIPLE OVENS 38B CASTER, SWIVEL WITH 3/4 STUD - SINGLE, DOUBLE, & TRIPLE OVENS WITH BRAKE LEG, 6 (152mm) ADJUSTABLE WITH 3/4 STUD - SINGLE, DOUBLE, & TRIPLE OVENS KIT, THERMOCOUPLE, 6 ( ) 41A CORD AND PLUG, L6-20P 41B CE CORD 11

12 View(s) of FRONT CONTROL AREA(s) 12

13 Parts for FRONT CONTROL AREA(s) ITEM QTY. P/N DESCRIPTION CIRCUIT BREAKER, 15 AMP CIRCUIT BREAKER, 3 AMP NAMEPLATE, MIDDLEBY MARSHALL 5 2 A6153 BOLT 5A KEEPER 5B SELF RETAINING NUT COOLING FAN, BLOWS IN TRANSFORMER, 240Vp:24Vs, 65VA AIR SWITCH, BURNER/BLOWER MOTOR, FRONT 9A IGNITION MODULE, US VERSION 9B IGNITION MODULE, CE VERSION 9C IGNITION MODULE, AUSTRALIAN VERSION SIGNAL AMPLIFIER, BOARD CONTACTOR, BLOWER MOTORS KIT, SELECTOR SWITCH, CONTACT BLOCK 12A CONTACT BLOCK 12B SELECTOR SWITCH KIT, CONVEYOR SPEED CONTROLLER WITH SELECTOR AND DIGITAL DISPLAY (INC. ITEM 14) DIGITAL DISPLAY KIT, DIGITAL TEMPERATURE CONTROLLER ITEM QTY. P/N DESCRIPTION TRANSFORMER, 230Vp:120Vs, 0.2 KVA, CONVEYOR SAFETY SWITCH, MACHINERY COMPART- MENT ACCESS PANEL, INTERLOCK GRILL, COOLING FAN, WITH FILTER FILTER ONLY HI-LIMIT CONTROL TRANSFORMER, 240/24V, SIGNAL AMPLI- FIER, 25VA CIRCUIT BREAKER, 1 AMP RESET BUTTON WITH GREEN LIGHT KIT, THERMOCOUPLE, 6 x 120 ( ) CONNECTOR, 12 WAY FOR P/N PACTROL IGNITION MODULE (CE ONLY) CATCH, DOOR (CE ONLY) CE ONLY LIGHTED RESTART SWITCH 27A BULB, 220V 27B PUSH BUTTON 27C ADAPTER 27D CONTACT BLOCK 27E SOCKET FOR BULB 13

14 View of GAS PIPING AND BURNER ASSEMBLY 14

15 Parts for GAS PIPING AND BURNER ASSEMBLY ITEM QTY. P/N DESCRIPTION ASSEMBLY, BURNER (INCLUDES ITEMS 1-12) ASSEMBLY, BURNER BLOWER AND MOTOR (INCLUDES ITEMS 2-4) VENTURI PILOT IGNITOR WITH NATURAL GAS ORIFICE PILOT SHIELD BRACKET, PILOT MOUNTING ORIFICE HOLDER/INLET CONNECTOR 14A MAIN ORIFICE, NATURAL GAS, (6.35mm) 14B MAIN ORIFICE, PROPANE, (3.86mm) 15A USE ITEM 6 FOR NATURAL GAS 15B PILOT ORIFICE, PROPANE, (0.46mm) HOSE CLAMP BRACKET, HOSE AND BURNER MOUNTING AIR DUCT, FLEXIBLE 20 A/R TUBING, SILICONE RUBBER, 1/4 /6.4mm DIA. ITEM QTY. P/N DESCRIPTION KIT, PILOT TEE 1/4 /6.4mm 23 A/R TUBING, ALUMINUM, 1/4 /6.4mm O.D VALVE, MODULATING GAS, 1/2 25A COMBINATION GAS VALVE (SAFETY REGU- LATOR), 1/2 25B COMBINATION GAS VALVE & GAS PRES- SURE SWITCH (CE ONLY) 25C KIT, COMBINATION VALVE, CONVERT NATURAL GAS TO LP, (INCLUDES CAP SCREW, O-RING, ADJUSTING SCREW AND LP SPRING) VALVE, SHUTOFF 1/ BRACKET, PIPE MOUNTING 1-1/ UNION, PIPE 1/ UNION, PIPE 1-1/4 30B KIT, CONVERSION FROM NATURAL GAS TO PROPANE (INCLUDES ITEMS 14B, 15B AND 25C) TUBE BLOWER EXTENSION (NOT SHOWN) IGNITION/SENSOR WIRE 15

16 View(s) of REAR BLOWER/MOTOR ASSEMBLY (CONVEYOR DRIVE END SHOWN) ITEM 37 GREASE CARTRIDGE ( ) NOT SHOWN ITEM 40 RFI FILTER NOT SHOWN 16

17 Parts for EACH REAR BLOWER/MOTOR ASSEMBLY ITEM QTY. P/N 1A B A A DESCRIPTION BLOWER WHEEL-CCW DRIVE END BLOWER WHEEL-CW, IDLER END PLATE, INLET RING SCREW, CAP HEX HD 3/8-16 x 3 LOCKWASHER, SPLIT 3/8 SPACER SHAFT SEAL, PTFE PLATE, SHAFT SEAL INNER SHAFT BLOWER KEY, BLOWER WHEEL BEARING SPACER, BEARING SCREW, CAP HEX HD FLATWASHER, 7/16 LOCKWASHER HEX NUT, 1/2-13 PULLEY, BLOWER, STANDARD, 6-1/2 ITEM QTY. P/N DESCRIPTION BELT, STANDARD (SEE BELOW) MOTOR, BLOWER 1HP BRACKET, MOTOR MOUNTING PULLEY, (BK65) STANDARD, MOTOR (SEE BELOW) KEY, PULLEY, 3/16" x 3/16" x 3/4" (5 x 5 x 19mm), MOTOR EXTENDER, FAN 34A FAN BLADE, CW, IDLER END 34B FAN BLADE, CCW, CONVEYOR, DRIVE END BRACKET, MOTOR SUPPORT KIT, THERMOCOUPLE, 6" (SOME MODELS HAVE A QTY OF 4) ( ) 37 A/R GREASE CARTRIDGE MOUNTING BRACKET SUPPORT BRACKET RFI FILTER (CE & AUSTRALIAN ONLY) RPM KIT HERTZ MOTOR PULLEY MTR PULLEY P/N DIAMETER BELT SIZE BELT RPM OF P/N W/SPLIT BUSHING SPLIT BUSH P/N DESCRIPTION P/N FAN BK /4 BX No Longer in Production BK /4 BX BK /4 BX BK90H /4 BX Hi-Altitude W/BUSHING BK90H /4 BX Hi-Altitude W/BUSHING BK /4 BX Standard 17

18 View of REAR CAPACITOR AREA ITEM 20 RFI FILTER, CE & AUSTRALIAN NOT SHOWN 18

19 Parts for REAR CAPACITOR AREA ITEM QTY. P/N DESCRIPTION AIR SWITCH 12 A/R TUBING, SILICONE BULK 1/4"/6.4mm O.D TUBING, ALUMINUM BULK 1/4 /6.4mm O.D SAFETY SWITCH, BLOWER MOTOR SHROUD, MOMENTARY ASSEMBLY START CAPACITOR (BLACK) - INCLUDES BRACKET AND END CAP CAPACITOR, RUN (SILVER) INSULATOR CAP, RUN CAPACITOR HOSE CLAMP KIT, THERMOCOUPLE, 6 x 120 ( ) (SOME MODELS HAVE A QTY OF 4) RFI FILTER (CE & AUSTRALIAN ONLY) 19

20 View of SINGLE BELT CONVEYOR ITEM 44 HEYCO PLIERS, NOT SHOWN 20

21 Parts for SINGLE BELT CONVEYOR ITEM OTY PART NO. DESCRIPTION ITEM OTY PART NO. DESCRIPTION WELDMENT, CONVEYOR DRIVE FRAME SPROCKET, CONVEYOR BELT WELDMENT, CONVEYOR CENTER FRAME COLLAR, SHAFT, WITH SET SCREW WELDMENT, CONVEYOR IDLER FRAME BUSHING, BRONZE 3/4" O.D. x 5/8" 1.D PIVOT PLATE SPACER, NYLON 1-1/4" O.D. x 3/4" I.D BUSHING, CONVEYOR ADJUSTMENT BRACKET, SHAFT SUPPORT 7 8 F716A8805 WASHER, EXTERNAL TOOTH 1/4" ADAPTER, DRIVE SHAFT LOCKNUT, HEX 1/4"-20 9A CONVEYOR BELT, COMPLETE, 32"W x 206"L (0.81 x 5.23m) 9B CONVEYOR BELT, 32"W x 12"L (0.81 x 0.30m) MASTERLINKS KIT, 32" (0.81m) BELT (INC.ITEMS 11-13) MASTERLINK, LEFT MASTERLINK, CENTER MASTERLINK, RIGHT SHAFT, IDLER SPROCKET, CONVEYOR BELT BUSHING, BRONZE 3/4" O.D. x 5/8" 1.D BRACKET, IDLER SHAFT ADJUSTMENT SCREW, CONVEYOR TENSION ADJUSTMENT BRACKET, SHAFT SUPPORT SHAFT, DRIVE SPROCKET, DRIVE SHAFT, 5/8" BORE, 15T, WITH SET SCREW ASSEMBLY, ROLLER CHAIN (62 LINKS) WITH MASTERLINK MASTERLINK, ROLLER CHAIN SPROCKET, DRIVE MOTOR, 5/8" BORE, 15T, WITH SET SCREW ADAPTER, DRIVE MOTOR WITH SET SCREW DRIVE MOTOR, 1/8 HP, 1400:1 (STANDARD) 35A DRIVE MOTOR, 1/8 HP, 600:1 (HIGH SPEED) 35B BRUSHES, DRIVE MOTOR, ASSEMBLY, PICKUP, DRIVE MOTOR END STOP, CONVEYOR, 29-1/4 LONG REAR STOP, CONVEYOR, 18 LONG CRUMB PAN, ALUMINIZED (WITH OPENINGS) TOOL, HEYCO PLIERS 21

22 View of Split Belt Conveyor ITEM 49 HEYCO PLIERS, NOT SHOWN 22

23 Parts for Split Belt Conveyor ITEM OTY PART NO. DESCRIPTION ITEM OTY PART NO. DESCRIPTION WELDMENT, CONVEYOR DRIVE FRAME COLLAR, SPLIT LOCKING WELDMENT, CONVEYOR CENTER FRAME BUSHING, BRONZE 3/4" O.D. x 5/8" 1.D WELDMENT, CONVEYOR IDLER FRAME SPACER, NYLON 1-1/4" O.D. x 3/4" I.D PIVOT PLATE BRACKET, SHAFT SUPPORT BUSHING, CONVEYOR ADJUSTMENT BUSHING, SPLIT BELT DRIVE SPROCKET 7 8 F716A8805 WASHER, EXTERNAL TOOTH 1/4" LOCKNUT, HEX 1/4"-20 9A CONVEYOR BELT, COMPLETE, 15"W x 206"L (0.38 x 5.23m) 9B CONVEYOR BELT, 15"W x 12"L (0.38 x 0.30m) MASTERLINKS KIT, 15" (0.81m) BELT (INC.ITEMS 11-13) MASTERLINK, LEFT MASTERLINK, CENTER MASTERLINK, RIGHT SHAFT, IDLER, REAR, 32-3/ FLAT WASHER, BRONZE, 1 O.D. X 1/2 I.D SHAFT, IDLER, FRONT, 16-3/ SPROCKET, CONVEYOR BELT BUSHING, BRONZE 3/4" O.D. x 5/8" 1.D BRACKET, IDLER SHAFT ADJUSTMENT SCREW, CONVEYOR TENSION ADJUSTMENT BRACKET, SHAFT SUPPORT SPROCKET, DRIVE SHAFT, 5/8" BORE, 9T, WITH SET SCREW ASSEMBLY, ROLLER CHAIN COMPLETE (62 LINKS) ASSEMBLY, ROLLER CHAIN COMPLETE (48 LINKS) MASTERLINK, ROLLER CHAIN SPROCKET, DRIVE MOTOR, 5/8" BORE, 15T, WITH SET SCREW ADAPTER, DRIVE MOTOR WITH SET SCREW DRIVE MOTOR, 1/8 HP, 1400:1 (STANDARD) 40A DRIVE MOTOR, 1/8 HP, 600:1 (HIGH SPEED) 40B BRUSHES, DRIVE MOTOR, ASSEMBLY, PICKUP, DRIVE MOTOR END STOP, CONVEYOR, 29-1/4 LONG REAR STOP, CONVEYOR, 18 LONG 48A CRUMB PAN, ALUMINIZED (WITH OPENINGS) TOOL, HEYCO PLIERS SHAFT, DRIVE, REAR, 35-1/ FLAT WASHER, BRONZE, 1 O.D. X 1/2 I.D SHAFT, DRIVE, FRONT, 17-3/ SPROCKET, CONVEYOR BELT SPACER, NYLON FITS BETWEEN SPROCKETS 23

24 Standard Finger Configuration and Parts D A A C X C A A D B E B E B X B E B E B Notes RT TO LT MIRROR IMAGE OF FINGER ARRANGEMENT MOTOR PULLEY: BK65 P/N BELT SIZE: BX67 P/N RPM= 1692 A = WLDMT, PLT OTR SL3 W/RASD MANF WLDMT, PLATE, INNER COL W/DAM ASSY, RAISED MANF W/SLD BAFFEL B = PLATE, OUTER S/L WLDMT, PLATE, INNER COL W/DAM ASSY, MANIFOLD W/FULL BAFFEL ALUZ C = PLATE, FULL BLANK ALUZ D = PLATE, BLANK PRTL 2.75 UPR 570 E = PLATE, BLANK PARTIAL ALUZ LWR570 F = G = 24

25 Wiring Diagrams (electrical schematics) 45520E r~-~--;::) ~J ' ' -~; J:::; ~:--,,,,, t--oco~--t --_::;-I_,., -' ~ _j_ MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G volt 50/60 Hz, 1 Phase 25

26 26 MIDDLEBY MARSHALL PS570G LADDER DIAGRAM G volt 50/60 Hz, 1 Phase 45520E1

27 I - -- I I ill['""":: "' I>-"'""'\ W I / "'D I I ~ "' _f ::1 I Zc r it! :<' i i i = u i l '' 1 c 2 0 J [-oco MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G volt 50/60 Hz, 1 Phase AU 46978D 27

28 28 MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G volt 50/60 Hz, 1 Phase CAN 47285C

29 ~ :;; ;:': -- : ~I / s " o j "' L ~ " ~~ Q ±I ~ 8! j_~ ~I ) _" E~!L ~! ~ ±: ' 8: ' ~:.& ' / t";;--- l'i C<. ;f lbi ~ ' ~! MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE DN 47263C O'~H 0~8 i:' ~ 0 29

30 30 MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE DUT 47265C

31 m ~ '.l ~ ~ b 0 ~ m.. ' ' ~,. I)! : d "~ r ~ '~ " ". 8 " "' c 5 ' '.f,_ A e z -,;- " 3~<Bl! ~: 'E: 0 ~:. : ' g ll:' GS MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE FR 47257C 31

32 32 MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE GM 47255C

33 8 ' "' B ' ~: i'< ~: MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE GK 47261C 33

34 34 MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE IT 47253C

35 ' ----->_>-----~;;~--- MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE SP 47259C 35

36 36 MIDDLEBY MARSHALL PS570G WIRING DIAGRAM G230 volt 50 Hz, 1 Phase CE UK 45587F2

37 37 MIDDLEBY MARSHALL PS570G LADDER DIAGRAM G230 volt 50 Hz, 1 Phase CE 45587F1

38 NOTES 38

39 NOTES 39

40 40