71685 Landing Light Kit Installation Instructions
|
|
- Branden Young
- 5 years ago
- Views:
Transcription
1 71685 Landing Light Kit Installation Instructions Overview The Whelen landing light kit is designed to install into the wingtip lens area of an RV. Its important to note that the tip installation of this light is not an ideal choice for a landing light location due to the obstruction of the tip cutout sidewall. But it does provide a suitable location at a low cost, without having to cut into the leading edge of the wing. The challenge of installing this light is to get the light as far outboard on the tip as possible so as to have the best chance of getting the light ahead and forward of the plane. Shown here is an aluminum plate cutout that represents the mounting surface. Your surface will be fiberglass. Kit components light assembly mounting bracket Nutplates and rivets Screws and washers Nylon angled spacers Springs Molex Connector and pins Installing the Light 1. Remove the existing backing plate from the light. This can be discarded. Remove wingtip and place it up on a table or other stable location to be worked on. 2. Take note of the small colored round covered hole on the back of the light. This is a cooling hole. 3. Take the mounting bracket, mark one side front, and countersink the holes for the ears of the nutplates on the front side. 4 nutplates will be installed. DO NOT countersink the holes where the screws will go! Cell version.02 1 Page
2 4. Place the light on the bracket and line up the holes in the light with the holes in the bracket. Take a look at the back of the bracket and see where the cooling holes are just for orientation. Make a mark where you will place a bend in the bracket. 5. Place the plate in a clamping device like a vice or brake. Tug on the top gently while taping the bottom lightly with a hammer to put a bend in the plate at your bend line. You want about 25 degrees of bend. The # of degrees is not critical. 6. Install all 4 #8 nutplates on the back side of the plate using the rivets and nutplates provided. 7. The inboard side of the plate is the square side, the outboard is the curved side. Place the light on the front side of the plate and install the #8 SS 1 screw and one washer on the inboard light hole. This screw will hold the light in place while you install the light with the springs. Be sure to orient the light on the plate with the cooling hole. 8. Now we are ready to get a handle on where the light cutout will go. Lets review a couple of things Cell version.02 2 Page
3 a. The light needs to go as far outboard as possible. This gives you the best angle opportunities to get the light pointed forward. b. The light needs to also be as low as possible to not be obstructed by any nav/strobe light assemblies. Take a few moments to get an idea of how the light will get pointed forward and down to the needed illumination area. c. Picture shown on the first page is the installation on a typical RV 7/8/9 installation. 9. Set the light assembly up into the tip and get an idea of how it will orient. If you set the light up against the outboard side of the tip, you can see if the bracket needs any final trimming to get further outboard in the tip. You may find you need to trim some off. 10. Cut out the light hole in the tip. Hole size should be ~2 5/8 x 1.5 square. The actual size is not that critical. Use the template provided. Clean the hole up and make the lines look nice. Folks will be poking around your cool lights and you want it presentable. 11. Drill the 3 holes for the #8 screws that hold the light in place on your mounting surface. Use the template provided. The outboard screw hole should start ~5/8 from the outboard edge of the lens area. On the outboard hole, after drilling the hole perpendicular to the mounting surface, angle the drill while drilling to be parallel with the wingtip edge to give the screw a straight shot at the bracket. The nylon spacer provided will be installed to deal with the angle. 12. Cut the springs to length with your favorite cutting tool. You need 2 springs 3 long, and 1 spring 1 long Cell version.02 3 Page
4 13. Install the light in the tip. Picture shows the order of the parts. Screw head, washer, nylon spacer, washer, mounting surface, washer, spring, washer, light assembly. Suggest a little bit of oil on the screws for ease of installation of the screws into the nutplates. The springs provide tension and allow the light adjustability. 14. Wire up the light and give it a test. I know, you tested that already just to see it work 15. With your plane leveled, adjust the light to the angle desired, Mark a spot on the wall of the height as a reference. You want ~3 degrees of down angle on the light with the plane level. 16. Check all avionics systems for interference from this installation. 17. Go fly and make any adjustments. Wiring No matter your installation type, the light wiring should be protected by a fuse or circuit breaker. A nice article on wire size by the man himself Bob Nuckolll A 20ga wire and a 2 amp fuse will protect the wire. If your using 2 of these lights on a single circuit, a 3 amp fuse will do the trick. No shielding is necessary on LED devices. A molex connector has been provided to disconnect your lights at the wingtip for easy tip removal. A how to article from Bob below on crimping these great little pins. Red wire +12VDC. Black wire GROUND. Other references. Mounting plate 5052 Aluminum Whelen Light: Weight with Lens 0.28 lbs. (127gm) 2.07 (53mm) x 3.64 (93mm) x Depth: (25mm) VDC Light color White Polycarbonate 30º optic spreader lens Whelen 5 year aviation LED warranty Cell version.02 4 Page
5 Check the drawing for scale when printing with an actual ruler! Cell version.02 5 Page
6 Kit contents Qty Description 1 Light mounting bracket 4 K nutplates 1 #8 Stainless Steel Screw 1 2 #8 Stainless Steel Screw 2 2 #8 Stainless Steel Screw 4 9 #8 Stainless Steel washer 1 Installation Document 1 7 spring, or springs cut to size (2 3, 1 1 ) 3 Nylon washers angled 8 AN426AD rivets Molex pin connector Cell version.02 6 Page
Page: REV 1: In Step 4 "a minimum of 1/16 [1.6 mm] gap" was "an approximately 1/16 [1.6 mm] gap."
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationSTOL CH 701. STOL CH701 cabin. Top view: Tunnel 7F11-4 between the Seats. STOL CH701 Seats
CH701 cabin Top view: Tunnel 7F11-4 between the Seats. CH701 Seats CHECK: If the Gusset 7F11-7 is supplied bent; hen it is best to install the Gusset before the Seat 7F16-1. Otherwise, install the Seat
More informationVAN'S AIRCRAFT, INC. SECTION 40: LIGHTING
SECTION 40: LIGHTING RIGHT WING ASSEMBLY W-00014 LENS LN-200-1 WING TIP NAV/POSITION/ STROBE LIGHT LL-200 LANDING LIGHT W-1223E LENS BACKING STRIP, W-1222-R EXTENSION W-1223B-L LANDING LIGHT RIB NOTE:
More informationPage: MEMO: In Figure 3, "2X 1 3/32 [27.78 mm]" was "2X 1 3/32 [2.75 mm]"
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationSECTION 22: FWD LOWER FUSELAGE VAN'S AIRCRAFT, INC F-1257 RUDDER PEDAL SUPPORT CHANNEL, 4 PLACES WD-1204 ENGINE MOUNT BRACKET, 2 PLACES
SECTION 22: F-1257 RUDDER PEDAL SUPPORT CHANNEL, WD-1204 ENGINE MOUNT BRACKET, VAN'S AIRCRAFT, INC. FWD LOWER F-1201B FIREWALL SHELF FIREWALL BOTTOM FUSELAGE TUNNEL RIB F-1271-R FWD FUSE CORNER SKIN F-1288
More informationROLL BAR FRAME 2 PLACES F-1231A-FL ROLL BAR FRAME F-1231C INBOARD F-1231B OUTBOARD ROLL BAR STRAP BAGGAGE BULKHEAD
SECTION 24iS/U: ROLLOVER F-1231A-FR ROLL BAR FRAME VAN'S AIRCRAFT, INC. F-1231A-AR ROLL BAR FRAME STRUCTURE F-1231E ROLL BAR SPLICE PLATE 2 PLACES F-1232A ROLL BAR BRACE F-01254-R-1 SUPPORT FRAME & F-01207
More informationREVISION DESCRIPTION:
REVISION DESCRIPTION: 1) Page: 12-03 REV 1: Step 1: and Figure 1: Final-Drill s.b. Match-Drill. Step 4: Updated flox mixture description to match later description (removed "peanut butter-like" description).
More information4-Bulkheads. Bulkheads. December XLR Page 4-1
Bulkheads December 2007 04-XLR Page 4-1 This Page Intentionally Left Blank Page 4-2 04-XLR December 2007 Contents 4.0 - Chapter Preface...4-4 4.0.1 - Parts List... 4-4 4.0.2 - Tools List... 4-4 4.0.3 -
More informationPage: MEMO: In NOTE before Step 5, "Whenever possible, ream using a drill press..." was "Always ream using a drill press...".
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationF-1202D-L PANEL ATTACH STRIP F L UPPER FWD FUSELAGE SKIN RIB F CABIN EGRESS HANDLE F-1240B COVER PLATE
SECTION 29iS/U: F-1202D-L PANEL ATTACH STRIP F-01240-1 UPPER FORWARD FUSELAGE SKIN (SHOWN TRANSPARENT) VAN'S AIRCRAFT, INC. FWD UPPER FUSELAGE F-00078 CABIN EGRESS HANDLE F-00077-L UPPER FWD FUSELAGE SKIN
More informationZODIAC 601 XL. Trim the outboard corner of the front flange of the center spar 6W4-1. Corner should not touch the side of the cabin floor skin 6B10-1.
Trim the outboard corner of the front flange of the center spar 6W4-1. Corner should not touch the side of the cabin floor skin 6B10-1. Tape the side skins to the cabin floor skin (area in front of the
More information1) Page: REV 5: Changed depiction to show added hardware and T-01220
REVISION DESCRIPTION: 1) Page: 37-01 REV 5: Changed depiction to show added hardware and T-01220 Page: 37-02 REV 4: Added Figure 3 depicting Separating the T-01220 Doublers. Figure 4 was Figure 3. Added
More informationPage REV 1: Added "Step 4: Bend the tabs on the wiring channel to match the slant of the F L & -R Tunnel Sides."
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationSERVICE BULLETIN NO. OSB
Page 1 of 12 SERVICE BULLETIN NO. OSB817-067 I. TECHNICAL DETAILS 1.1 Category: Optional 1.2 Airplanes affected: all S/N 1.3 Time of Compliance: On holders discretion 1.4 Subject: ATA-Code: 33-40 Exterior
More informationInstallation Instructions February 2009
Installation Instructions February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 The Hammer Head Assembly Installation Instructions (Rollerbar & Direct
More informationVAN'S AIRCRAFT, INC. SECTION 19: WING SYSTEMS ROUTING
VAN'S AIRCRAFT, INC. SECTION 19: WING SYSTEMS ROUTING RIGHT WING ASSEMBLY WH-00011 WING TIP LIGHTING HARNESS WH-00013 AP SERVO HARNESS LEFT WING ASSEMBLY W-00027 PITOT LINE WH-00012 ADAHRS HARNESS WH-00011
More informationPage REV 1: In Step 1, added reference to fluid fitting clocking. Added Figure 2 and Figure 3.
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm DOCUMENTATION
More informationPage: REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS.
REVISION DESCRIPTION: 1) Page: 32-03 MEMO: Step 4 should not be bold. Fix WD-1213 callout in Figure 3. Page: 32-04 REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS. Add make
More informationInstallation Instructions Models 2858, 2858A-1, 2858GL February 2009
Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 Step 1 Head Assembly Installation Instructions
More information12/03 EXPLODED VIEW 1) L angles on first rear rib: moved from inboard to outboard side of rib (12/03)
ZODIAC CH 601 XL Drawing list December 04, 2003 3 rd revision of 2 nd edition 12/03 Summary of revisions from 07/03 to 11/03 AIRFRAME 6-X-0 DRAWING LIST Dec 4, 2003 6-X-1 6-T-0 6-T-1 6-T-2 6-T-3 6-T-4
More informationAg Leader Technology. Combine Installation New Holland TC 57, 59. Monitor Installation
Monitor Installation Figure 1. Monitor installed on right side cab window using window mount bracket. 1. If you are in very humid conditions where moisture may condense on the glass where you are mounting
More informationJune 16, 1947 OPTIONAL CHANGE SERVICE BULLETIN NO. 17 INSTALLATION STEERABLE TAIL WHEEL. (Includes Supplement 1 and Supplement 2)
SERVICE BULLETIN REPUBLIC AVIATION CORPORATION FARMINGDALE, LONG ISLAND, NEW YORK SERVICE DEPARTMENT June 16, 1947 OPTIONAL CHANGE SERVICE BULLETIN NO. 17 INSTALLATION STEERABLE TAIL WHEEL (Includes Supplement
More informationSection 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A
RotorWay International Page A Tail Rotor Drive Procedures covered in this section: Install driveshafts and gearboxes; install drive belt and tensioner; fabricate and install tail rotor pitch actuator arms;
More informationInstallation. minnkot amot or s.com
Installation minnkot amot or s.com INSTALLATION Your Talon comes complete with the items listed below. Please take a moment to familiarize yourself with the parts list and tools needed prior to starting
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More information11 - Fairings. Fairings. February XLF Page 11-1
11 - Fairings Fairings February 2003 11-XLF Page 11-1 11 - Fairings This Page Intentionally Left Blank Page 11-2 11-XLF February 2003 11 - Fairings Contents 11.0 - Chapter Preface... 11-4 11.0.1 - Parts
More informationTable of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03
Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator
More informationYOU MUST WEAR SAFETY GLASSES DURING EACH STEP OF THESE INSTRUCTIONS
Machine Racer: Rally Preparation 1. Print the Working Drawing of the design you created and simulated in the Mousetrap Car 2.0 STEM Application. You can find your Working Drawing in the "Outputs" tab of
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will
More informationREVISION DESCRIPTION:
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More information12NPR Reason For Revision
12NPR 04-03-14-1 Reason For Revision 1) RV-12 SkyView Touch Avionics Kit 2) RV-12 SkyView AP-Knob Panels Kit (58) 3) Add instructions for installation of F-00062. 4) Allow use of lighter springs on RV-12
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic
More informationREVISION LIST CHAPTER 6: AILERON CONTROLS
REVISION LIST CHAPTER 6: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationREVISION DESCRIPTION:
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationREVISION LIST CHAPTER 21: FLAP SYSTEM COMPLETION
REVISION LIST CHAPTER 21: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationREVISION LIST CHAPTER 14: CENTER CONSOLE
REVISION LIST CHAPTER 14: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationFLAP, AILERON, FLAP/FUSELAGE AND STABILATOR GAP SEAL INSTALLATION AND MAINTENANCE MANUAL
FLAP, AILERON, FLAP/FUSELAGE AND STABILATOR GAP SEAL INSTALLATION AND MAINTENANCE MANUAL Aircraft Eligibility: Piper PA-28-151, PA-28-161, PA-28-181, PA-28-201T, PA-28-236, PA- 28R-201, PA-28R-201T, PA-28RT-201,
More informationWPS-104 Heater. Installation Instructions
WPS-104 Heater Installation Instructions For 2007 vehicles see page 15 WPS 104 HEATER SYSTEM INSTALLATION INSTRUCTIONS If this is a complete installation of top, windshield and heater system, for ease
More informationFIGURE 2: ADDING FITTINGS TO BRAKE ASSEMBLY (RIGHT SHOWN) FIGURE 1: ATTACHING AND ALIGNING THE MAIN GEAR AXLES
VAN'S AIRCRAFT, INC. Step 2: Apply pipe thread sealant and attach the fluid fittings to the brake as shown in Figure 2. Note that the brakes should mirror each other when installed. Step 1: Bolt the main
More informationSERVICE KIT thru , 631, 634, 675 R thru R F thru F FR thru FR
TITLE SEAT BELT AND SHOULDER HARNESS KIT INSTALLATION EFFECTIVITY MODEL SERIES SERIAL NUMBERS 182 33000 thru 18268368 182 613, 631, 634, 675 R182 R18200001 thru R18201973 F182 F18200001 thru F18200169
More informationInstallation Instructions
Installation Instructions Speedcook Oven Read carefully. Keep these Instructions. INSTALLATION INSTRUCTIONS Electrical Requirements Product rating is 240/208 volts AC, 60 Hertz, 30 amps and 6.5 kilowatts.
More informationKI (14V) & KI (28V) R44
KI-228-1 (14V) & KI-228-2 (28V) R44 Radar Altimeter Installation Kit Instructions For B050 upper console only; includes parts for In-Console and Above-Console installations. NOTE Visit www.robinsonheli.com
More informationINSTALLATION INSTRUCTIONS CHEVY C-10 4-Link Rear End
INSTALLATION INSTRUCTIONS 73-87 CHEVY C-10 4-Link Rear End Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating to ensure proper
More informationPN PONTIAC FIREBIRD. Kit Contents: Four Panel Sequential LED Tail Light Kit Installation Guide
1969 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100569 1969
More informationSECTION 35iS/U: LANDING GEAR & ENGINE MOUNT
WD-1221 ENGINE MOUNT STANDOFF SECTION 35iS/U: LANDING GEAR & ENGINE MOUNT U-01203E-1 INBOARD DOUBLER PLATE U-01203B-1 INBOARD WEAR PLATE U-01203C-1 BEARING PLATE U-01203-2 (U-01203-1 SHOWN) INBOARD MAIN
More informationThis LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506.
L.E.D. INSTRUCTIONS I D T S O T U B I R M O C R Y N A P Kit contains: This LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506. For the power supply: 1-LED power supply circuit board, 2
More informationMiG-29 Retract Kit (for the HET-RC Mini Air Retract System)
MiG-29 Retract Kit (for the HET-RC Mini Air Retract System) The MiG-29 Retract Kit was designed to allow the easy installation of the HET-RC mini Air Retract system into the twin EDF MiG-29. We recommend
More informationCombine Cover Manual
Combine Cover Manual Installation Instructions Page 27 Operating Instructions Page 8 Warranty Page 8 Trouble Shooting Page 9 11 For Model s: Case I.H. 2388, 2188, 1688 and 1680 With a MAURER Hopper Extension
More informationBlue Sky Sun Visors. RV-10 Installation Instructions. - Portable drill - 9/64 drill bit - 5/64 drill bit
Blue Sky Sun Visors RV-10 Installation Instructions Tools needed: - Portable drill - 9/64 drill bit - 5/64 drill bit - 100 Degree Countersink Bit - Phillips #2 Screwdriver - Measuring tape - Pencil Step
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL MOONEY M20 SERIES & M22 STC NO. SA4342NM NOTE: READ THESE DIRECTIONS BEFORE STARTING!
INSTALLATION REPORT NO. 08059 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL MOONEY M20 SERIES & M22 NOTE: READ THESE DIRECTIONS BEFORE STARTING! THIS DOCUMENT
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL PA28/PA32 STC # SA00762SE
INSTALLATION REPORT NO. 08067 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL PA28/PA32 STC # SA00762SE NOTE: READ THESE DIRECTIONS BEFORE STARTING! CHECK FOR
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationEXPRESS ASSEMBLY MANUAL SECTION 3 F5-RG/FT WING ASSEMBLY. Procedure 3.050A INSTALLATION OF AILERON TORQUE TUBE ASSEMBLY
Procedure 3.050A INSTALLATION OF AILERON TORQUE TUBE ASSEMBLY In this procedure The aileron torque tube will be assembled and installed in the wing. Part Number Description Quantity 111-24-050 Torque Tube,
More informationStay-IN-Play with Panic Stop Braking
INSTALLATION INSTRUCTIONS TOWED VEHICLE BRAKING SYSTEM Stay-IN-Play with Panic Stop Braking SMI Manufacturing, Inc. P.O. Box 14040 Evansville, IN 47728 1-800-893-3763 www.smibrake.com SIP0906 Model SIP0603
More information2000 SERIES SPEEDBRAKE INSTALLATION MANUAL STC NO. SA2602NM
INSTALLATION REPORT NO. 08062 Serial Number PRECISE FLIGHT, INC. 800-547-2558 2000 SERIES SPEEDBRAKE INSTALLATION MANUAL CESSNA 210G, T210G, 210H, 210J, 210K, T210J, 210L, T210L, 210M, T210M, 210N, P210N,
More informationGlaStar and Sportsman Service Bulletin 67
GlaStar and Subject: Applicability: Issue: Compliance Time: Elevator counterweights All GlaStar and Aircraft Counterweight attachment to elevator end rib At or before next condition inspection Discussion
More information564 Shadowbox Face (w Screen) Instructions
Packing List Compatibility Face Bottom Shield (2) Face Brackets (8) Screws (#8 x 3/8 Phillips) (5) Screws (#8 x 5/8 hex head) Drill Template 11/64 Drill Bit Items Used with Optional Switch Box (see note
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationPost-Paint>Fuselage>Assemble instrument panel. Objectives of this task: Materials and tools required: Prepare the work area
Post-Paint>Fuselage>Assemble instrument panel Objectives of this task: To fit all instruments into the instrument panel, fit all of the electrical wiring and terminate to multi-pin connectors ready for
More informationSECTION 47: COWL BAFFLE VAN'S AIRCRAFT, INC. CB RIGHT AFT BAFFLE CB CYLINDER 3 BAFFLE VA-187 4" FLANGED DUCT
SECTION 47: CB-00014 CYLINDER 3 BAFFLE CB-00015 RIGHT AFT BAFFLE VA-187 4" FLANGED DUCT COWL BAFFLE CB-00031-R MAGNETO COOLING TUBE CB-00016 AFT CENTER BRACKET CB-00017 LEFT AFT BAFFLE CB-00013 RIGHT AIR
More informationSAFETY WARNING Please read these before operating your Sky Vector
www.megatech.com Entire contents Megatech 2002 Congratulations! You have just purchased the EASIEST plane to fly in the world! Learning to fly has never been so fun! Get ready to hand launch into gravity-defying
More informationThis document goes through the basic steps required to utilize the electric window motors from the Ford Mk3 Mondeo.
Modifying Ford Mk3 Mondeo door glass motors The options for installing electric windows in a Diablo replica are limited to only a few options; You can install the original motor and cable runners at 500
More informationFAX
INSTALLATION INSTRUCTIONS 6090 Air Suspension Kit (pat. pending) 1999-2006 Tahoe, Suburban, Avalanche, Yukon Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationREVISION DESCRIPTION: REV 2: Steps re-written for clarity REV 2: Steps re-written for clarity.
REVISION DESCRIPTION: 14-04 REV 2: Steps re-written for clarity. 14-05 REV 2: Steps re-written for clarity. SECTION 14: W-1012-L OUTBOARD W-1012-R TRIMMED OUTBOARD S W-1012-L OUTBOARD W-1025B-R FLAP HINGE
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More informationTrident Universal. Installation Manual
Trident Universal Installation Manual Revision 1.1; Updated: July 6, 2017 Table of Contents Tool List 03 Installation Tool List Pre-Install Preparation 04 Lateral Panel Modifications 07 Top Panel Modifications
More informationAssembly Instructions
Assembly Instructions CONTENTS Product Overview... 2 List of Assembly Components... 4 General Specifications... 5 Product Inspection Report (PIR)... 6 Cutting Instructions... 10 Slats... 10 Motor Tube
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationInstalling and Adjusting Cooling Baffles. Duct and Air Dam Construction. Firewall-Forward Instruction Manual--General
Firewall-Forward Instruction Manual--General Installing and Adjusting Cooling Baffles Like most air-cooled engines, Jabiru engines rely on ram air moving through a properly-constructed air duct for adequate
More informationINSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools:
INSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools: Drill Bits: 9/16 (.5625 ) Power Drill Socket Wrench Set Square #2 Driver Rubber Mallet Utility Knife
More informationSECTION 26iS/U: FUEL TANK VAN'S AIRCRAFT, INC. T R OUTBOARD RIB IE-00001X MECHANICAL FUEL GAUGE T R INBOARD RIB T R
VAN'S AIRCRAFT, INC. SECTION 26iS/U: IE-00001X MECHANICAL FUEL GAUGE T-01222-R OUTBOARD RIB FUEL TANK T-01223-R INBOARD RIB T-01228 RETURN LINE BRACKET T-01224-R INBOARD RIB T-01229 INLET ASSEMBLY T-01223-L
More informationFUSELAGE CABIN ASSEMBLY
SECTION 3 Cabin Frame Ref Dwg 8FC-3 The Top of the Cabin Frame is level The distance between the front and rear wing attachment to fit the wings SECTION 3 - Page 1 of 10 CABIN FRAME 8F18-1 The TOP TUBES
More informationPIRANHA I & 2 INSTALL GUIDE
TOP Use 5/32" drill bit DO NOT LET DEADRISE INTERSECT THIS LINE PLACE EITHER CORNER ON DEADRISE ANGLE PIRANHA I & 2 INSTALL GUIDE Two components need to be installed on the boat: the transducer and the
More informationAdditional Instructions for 6" Drop
Serving the Truck & Trailer Industry Since 1944 Additional Instructions for 6" Drop Attention Dealers: Please give this manual to the customer when product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationLearning to Set-Up Your Warrior Drive Belt Arizona Warrior (Rev4) BEFORE GETTING STARTED
BEFORE GETTING STARTED 1. A noise one guy calls 'howling' is the same noise another guy calls 'squealing' so unless you are both hearing the noise with your own ears its better to not assume a drive belt
More informationEFFECTIVITY Serial Numbers thru , 698
Conquest TITLE AILERON HINGE BRACKET REPLACEMENT EFFECTIVITY Model Serial Numbers 441 441-0001 thru 441-0349, 698 DESCRIPTION To install stainless-steel aileron hinge brackets as a replacement for aluminum
More informationMain Gear Doors (Apr 2009) Matt Kurke, ICS #10288
Main Gear Doors (Apr 2009) Matt Kurke, ICS #10288 A few thoughts to consider if you are having a problem with the main gear doors retracting and/or fitting properly on your Comanche Read section 6-39 (below)
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationCOMPONENT WORK SAMPLE 8 Simulated Assembly MAINTENANCE MANUAL. From 1974 to March 15, 2003
COMPONENT WORK SAMPLE 8 Simulated Assembly MAINTENANCE MANUAL From 1974 to March 15, 2003 Copyright 2008 VALPAR International Corporation P.O. Box 5767 Tucson, Arizona 85703-5767 All rights reserved. No
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 27035-29095 2005 RL Issue Date MAY 2005 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals
More informationAppendix D. Vizion PMA Autopilot Piper PA-28/32 Installation
Appendix D Vizion PMA Autopilot Piper PA-28/32 Installation RESTRICTION ON USE, DUPLICATION, OR DISCLOSURE OF PROPRIETARY INFORMATION THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TRUTRAK FLIGHT SYSTEMS,
More information2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
More informationOUTSIDE OF VEHICLE INSIDE OF VEHICLE
LAND ROVER DEFENDER 90 / 110 / TDi/ TD5/ PUMA Aluminium GULLWING DOOR MKII GWLD009 INSTALL TIME: 3 Hours OUTSIDE OF VEHICLE INSIDE OF VEHICLE IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 33590 2007 RL Issue Date AUG 2006 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals TOOLS
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will
More informationAFT MOUNTED OXYGEN SYSTEM INSTALLATION BEECHCRAFT 33, 35, 36, 55, AND 58
ENGINE TECHNOLOGIES INC. REPORT 35-4960004, REV. A, JULY 12, 2013 INSTALLATION INSTRUCTIONS FOR OXYGEN SYSTEM ON HAWKER BEECHCRAFT S35, V35, V35A, V35B, 35-C33A, E33A, 36, A36, F33A, G33, 95-55, 95-A55,
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationNEW PRODUCT RELEASE. PRODUCT/KIT NAME: 12 Stabilator Tip Fairing Kit
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm NEW PRODUCT
More information700 Pine Ridge Road Golden CO Tel (303) (888) 4X4 SLEE Fax (303)
700 Pine Ridge Road Golden CO 80403 Tel (303) 278 8287 1(888) 4X4 SLEE Fax (303) 278 7182 Slee Off-Road 1998-07 Land Cruiser / LX470 (* Requires AHC Removal) - Second Instructions Qty Parts Included Suggested
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationPage REV 1: Added 'Step 2: See the "REMOVE THIS TAB, BOTH SIDES" callout near Detail A. Modify four SB375-4 Snap Bushings as shown.
14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION
More informationCOMANCHE GEAR Regent Circle Naples, FL Phone & fax 239/ Cell 239/ Main gear doors miscellaneous
COMANCHE GEAR 10340 Regent Circle Naples, FL 34109 Phone & fax 239/593-6944 Cell 239/404-7524 www.comanchegear.com Main gear doors miscellaneous Here are a few thoughts to consider if you are having a
More informationPIRANHA I & 2 INSTALL GUIDE
PIRANHA I & 2 INSTALL GUIDE Two components need to be installed on the boat: the transducer and the control head. The control head displays sonar information, the transducer sends and receives sonar signals
More informationINSTALLATION INSTRUCTIONS SKID STEP and Utility Handles FOR MDHI 369D, 369E, 369FF, & 500N
INSTALLATION INSTRUCTIONS SKID STEP and Utility Handles FOR MDHI 369D, 369E, 369FF, & 500N AEROCRAFT INC. 4420 COMMODITY WAY, UNIT B SHINGLE SPRINGS, CA 95682 LOG OF REVISIONS REVISION DATE PAGES EFFECTED
More informationI n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION
I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2
More information36-01 REV 1: Updated figure to depict current F Bellcrank configuration.
REVISION DESCRIPTION: 36-01 REV 1: Updated figure to depict current F-00067 Bellcrank configuration. 36-06 REV 1: Updated Figure 1 and Figure 2 to depict current F-00067 Bellcrank configuration. 36-07
More informationBBK Caster/Camber Kit (87-93)
BBK Caster/Camber Kit (87-93) Materials in the box 2 Polished Aluminum Plates 2 Steel Strut Mounts 4 Polyurethane Bushings 2 Stud Plates 2 Bushing Sleeves 2 5/8 Flat Washers 2 5/16 Allen Head Bolts 4 5/16
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum
More information