INSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools:
|
|
- Albert Peters
- 6 years ago
- Views:
Transcription
1 INSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools: Drill Bits: 9/16 (.5625 ) Power Drill Socket Wrench Set Square #2 Driver Rubber Mallet Utility Knife Page 1 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
2 FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS PARTS LIST PARTS LIST: Description Qty. Part No. FORD PI SEDAN, OS-BELT 1 PI02 Ford PI Sedan Seat, OS-Belt Trim 1 PI51 OUTSIDE BELT COVER KIT 1 P300 Toothed C- Retainer 2 P004 #6x0.625 Sheet Metal Screw, Black 8 P057 CENTER BELT COVER KIT 1 P301 Belt Slot Cover 2 P005 #6x0.625 Sheet Metal Screw, Black 14 P057 STORAGE TONGUE KIT 1 P302 Storage Tongue 2 P003 #10 x 0.75 Pan Head Square Drive Self Drilling Screw 4 P051 RETRACTOR KIT, FORD PI SEDAN 1 PI71 Retractor 2 P001 Seat Belt Sliding Buckle 2 P002 Hip-Side Tongue 2 PI81 ½-13 Serrated-Flange Hex Locknut 1 P155 ½-13 x 1.0 Serrated Flange Hex Cap Screw, Black 1 P204 Retractor Mount, Ford PI 1 PI86 REAR DECK KIT, FORD PI SEDAN 1 PI72 ½ Standard Washer 1 P102 ½-13 Jam Nut 1 P151 ½-13 Serrated-Flange Hex Nut 1 P155 ¾ Steel Spacer 1 P109 Rear Deck Reinforcement Plate 1 PI83 SEAT MOUNTING KIT, FORD PI SEDAN 1 PI77 #14 x 1.5 Hex Head Self Drilling SMS, Black 7 P055 P300 P301 P302 PI77 P057 P004 P057 P005 P051 P003 P055 PI71 PI72 P001 PI83 P102 P155 P109 P151 P002 PI81 PI86 P204 P155 Page 2 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
3 Ford PI Sedan with OS-Belt Installation Instructions NOTE: IF INSTALLING A FLOOR PAN DO SO BEFORE INSTALLING SEAT. CAUTION: LOCATE ALL WIRING, FUEL LINES, BRAKE LINES, AND/OR COOLING LINES BEFORE DRILLING HOLES OR INSTALLING FASTENERS. NOTE: WAIT TO INSTALL CENTER PARTITION UNTIL AFTER YOU HAVE INSTALLED THE SEAT. THE SEAT REQUIRES THAT THE FRONT SEATS BE MOVED FORWARD TO ALLOW INSTALLATION. 1. Remove Factory Seat a. Remove bottom seat: unclip front lever latches, lift up slightly, slide back, and lift out. b. Remove the nuts from the three seatbelts on the bottom the vehicle. c. Remove the seat back by removing the nuts from the bottom studs then releasing the two latches at the top (The pull cords for releasing latches may be tucked behind the seat and more easily accessible from the trunk). [Pic 1] Factory Seat Removed (We suggest leaving the latches on to act as locating points for the seat) d. Remove top deck for easy access and remove factory seatbelts. e. Replace all remaining nuts back onto the original studs for keeping. Pic 1 2. Gently bend the child seat anchors (that are welded to the frame) so they are no more than 1.5 inches above floor pan. Note: These will need to be bent back for vehicle resale. [Pic 2] Bend Child Seat Anchors Page 3 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1 Pic 2
4 3. Install the Retractor Kit (PI71). a. Remove the three nuts on the upper level of the middle plate that is connected to the frame. [Pic 3] b. Put Retractor Mount Assembly over the three studs and re-secure the nuts. [Pic 3] Install Retractor Assembly Remove/Install Nuts c. Using bolts and bolt locations for the factory seatbelt retractors, install (2) Hip-Side Tongues (PI81). [Pic 4] Pic 3 Install Hip-Side Tongues Pic 4 4. Install Rear Deck Kit (PI72). a. Remove plastic cover for middle child seat anchor in top deck. [Pic 5] b. From inside the trunk, use a 9/16 drill bit to enlarge the hole in the sheet metal of the top deck just behind the middle child seat anchor. [Pic 6] c. Cut away enough of the top deck to allow the bolt to come up through the top deck without interference. Page 4 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
5 Remove Plastic Cover Pic 5 Drill Out Hole (Trunk View) Pic 6 d. Using (1) ½ Standard Washer (P102) and (1) ½-13 Jam Nut (P151), install (1) Rear Deck Reinforcement Plate (PI83) through recently enlarged hole by placing the washer over the screw and securing the jam nut. Place the (1) ¾ Steel Spacer (P109) and (1) ½-13 Serrated Flange Hex Locknut (P155) onto the screw but wait to tighten. [Pic 7] WARNING: A CRITICAL WIRE HARNESS RUNS BENEATH THE TOP DECK IN THE VICINITY OF WHERE THIS BOLT IS PLACED. EXERCISE CAUTION TO NOT PINCH THIS WIRE HARNESS BETWEEN THE NUT, WASHER, AND BOLT ASSEMBLY. Page 5 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
6 PINCHING THIS WIRE HARNESS WILL CAUSE A MALFUNCTION IN ONE OR MORE ELECTRICAL SYSTEMS DUE TO THE SYSTEMS BECOMING GROUNDED. (The two ends of the retractors will be connected later) Assemble Rear Deck Kit (Exploded View) 5. Cut a ¼ inch slot along the rubber door trim just above the hard plastic lower door trim. This is to allow the seat to sit underneath the rubber trim. Repeat for other side. Pic 7 Cut ¼ Slot 6. Install Ford PI Sedan Seat (PI51) in vehicle with Seat Mount Kit (PI77). a. Feed Retractor webbing through the slots in the middle hump of the Ford PI Sedan Seat. b. Top of seat will rest on the factory latches and against front edge of top deck. c. While lowering Ford PI Sedan Seat, feed (2) Hip-Side Tongue through outboard slots. d. Feed Ford PI Sedan seat under rubber door trim on both sides. [Pic 9] Pic 8 Page 6 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
7 Feed Seat Under Rubber Trim Pic 9 e. While firmly holding seat in place, use provided locations in the seat to drill pilot holes into the sheet metal of the vehicle. NOTE: WE STRONGLY RECCOMEND USING A CENTER PUNCH THRU THE HOLES IN THE PLASTIC SEAT TO SPOT THE LOCATION IN THE SHEET METAL PRIOR TO DRILLING FOR SCREW HOLES. f. Use the (5) #14x1.5 Hex Head Self-drilling Sheet Metal Screws (P055) in the provided holes to secure the seat to the vehicle; two on bottom, three on top. [Pic 10] NOTE: BE SURE THAT CABLES/WIRES ARE TUCKED FAR ENOUGH UNDER THE SEAT SO THAT THEY DON T INTERFERE WITH THE SEAT CONTACTING THE VEHICLE. Install 5 #10 Sheet Metal Screws Pic 10 Page 7 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
8 7. Install Outside Belt Cover Kit (P300) a. Place (1) Toothed C-Retainer (P004) on webbing of outboard seatbelt and outboard slot so that it pinches webbing and closes gap around webbing. Secure with (4) #6 x Sheet Metal Screws (P057). [Pic 11] b. Repeat for other side. Install Toothed C-Retainer 8. Install Center Belt Cover Kit (P301) a. Install (2) Belt Slot Cover (P005) around Retractor webbing using the built-in cutout in the Belt Slot Cover. Cutout should face away from prisoners (towards center) to avoid pinching the webbing. b. Using (14) #6 x Sheet Metal Screw, Black (P057), install Belt Slot Covers to the Ford PI Sedan Seat. c. Slide (2) Seat Belt Sliding Buckle (P002) onto Retractor webbing. Check buckle to ensure button is facing the desired direction. [Pic 12] Pic 11 Install Belt Slot Covers Pic 12 Page 8 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
9 9. Using (1) Serrated-Flange Hex Nut already located on the top deck, extend and secure connector plates of the Retractors to the top deck between the Rear Deck Spacer and Hex nut. [Pic 13] Secure Connector Plates 10. Install the Storage Tongue Kit (P302) a. Using (4) #10x0.75 Square Drive Self-Drilling Screw (P051) and (2) Storage Tongue (P003), secure the Storage Tongues to the vehicle Center Partition. Be sure to install the Storage Tongues low enough in the vehicle to avoid head injury during prisoner entry and exit. [Pic 14] Pic 13 Pic14 Page 9 of 9 PTS FORD PI SEDAN INSTRCUTIONS: OS BELT VERSION: B.1
Dodge Charger
LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Replacement Seat/ CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
More informationDodge Charger
LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Cover Seat/ CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. #12
More informationLevel of Difficulty Easy. Product Image. Front Mounting Bracket (553204) AC Mounting Bracket (553211) Tools Required Socket, 1/2"
INSTALLATION MANUAL Parts List 3 2 1 1 1 3 2 4 13 16 13 16 2 2 14 Front Mounting Bracket Middle Mounting Bracket Rear Mounting Bracket AC Mounting Bracket AC Top Mounting Bracket U-Bolt 3" U-Bolt 3.75"
More information2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE.
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6 OVAL STEPS UNIVERSAL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK
More informationCENTER BELT SYSTEM INSTALLATION INSTRUCTIONS CARCG121220
CENTER BELT SYSTEM INSTALLATION INSTRUCTIONS 2013+ DODGE CHARGER Distributed by CARCG121220 Important Notice: Read all instructions before starting the installation of the seat. Before drilling or installing
More informationATLAS TRANSFER CASES CABLE SHIFTER units built after 5/1/12
KIT CONSISTS OF: No. Qty Part No. Description P.O. Box 247, 4320 Aerotech Center Way PAGE 1 OF 6 Page Rev. Date: 08-01-17 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302060 BOOT- TWIN STICK 3 1 302063 BOOT RING-
More informationSeat belts. Safety precautions for handling pyrotechnic seat belt tensioners WARNING!
Page 1 of 41 69-1 Seat belts Safety precautions for handling pyrotechnic seat belt tensioners WARNING! Testing, removing, installing and repair work must only be carried out by properly qualified personnel.
More informationMUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1
2005-2011 MUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1 Thank you for purchasing our 2005-2011 Mustang Tiger Cage. Please read through all of the instructions first and then start installing the kit. We
More informationWARNING! THIS PRODUCT MUST BE INSTALLED BY A TRAINED, AUTHORIZED RICON SERVICE TECHNICIAN.
II. INSTALLATION T he chapter provides instructions for installing the RICON RDO2900 Series Internal Power Swing Door Operator into full-size 1992 and later Ford vans, 1990 and later Chevrolet & GMC vans,
More informationMustang Classic LightBar Instructions
1994-2004 Mustang Classic LightBar Instructions Note: Read installation instructions before starting. Component List: 1 LightBar 4 Poly Plugs 4 LightBar Bolts 4 LightBar Washers 2 LightBar Rivets 2 Light
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationSize Grade Torque 9/ ft/lbs. 5/ ft/lbs. 3/ ft/lbs. 7/ ft/lbs ft/lbs.
Ford 150 5 1/2, 6 1/2 & 8 Boxes 4/16 HJ32003,Rev 2 BOlT TORQUE SPECIFICATIONS STANDARD BOlTS: Size Grade Torque 5/16 5 20 ft/lbs. 3/8 5 35 ft/lbs. 7/16 5 56 ft/lbs. 1/2 5 85 ft/lbs. Size Grade Torque 9/16
More informationSeatbelt Solutions
Seatbelt Solutions www.seatbeltsolutions.com 3-Point Conversion Seatbelt Installation Guide for: 1947-1967 Trucks Seatbelt Solutions 90 Degree Bracket 7/16 Stud Plate 1 1/2 x 7/16 x20 Bolts Pop Rivets
More informationATLAS TRANSFER CASES CABLE SHIFTER units built before 4/30/12
Paso Robles, CA 93447 PAGE 1 OF 5 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 302051 TWIN STICK BASE MOUNT 2. 1 302060 TWIN
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationInstallations Instructions for Maier Racing Front Coilover Kit MS Ford Mustang
22215 Meekland Avenue Hayward, CA 94541 Phone: (510) 581-7600 Fax: (510) 581-2406 Installations Instructions for Maier Racing Front Coilover Kit MS-02-001 1964-1973 Ford Mustang Contents Front Coilover
More informationWJ AUTO TRANS. ATLAS SHIFTER
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 8 1 1 302051 BASE- ATLAS TWIN STICK MOUNT 2 1 302080 STUD BOLT 1/2-13 X 7 B7 3 1 303120 Serrated-Flange Hex Locknut 1/2-13
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationCetra Assembly Instructions
99877 Revision F- Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 0 Kimball International, Inc. T 800.8.88 F 8.8.800
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationInstallation Instructions
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 13mm, 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationRS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.
RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch
More informationInstallation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationINSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty
INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 13mm Drill Bits: 1/4, some older models a 1/2 Other Tools: Drill, Saber Saw 5/8 Fasteners From Hitch Fastener Kit Installation Instructions GOOSENECK
More informationInstallation Instructions PART NUMBERS: 24954, 77336, CQT24954
Cequent Performance Products, Inc. Installation Instructions PART NUMBERS: 24954, 77336, CQT24954 LIMITED LIFETIME WARRANTY To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE: ALWAYS read, understand
More informationRoll Bar (MMRB-6.1 to -6.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Roll Bar (MMRB-6.1 to -6.7) NOTE: These instructions cover Roll Bars with
More informationMM Panhard Bar, Mustang (MMPBA)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Panhard Bar, 1979-98 Mustang (MMPBA) Important Note for Customers with Baer
More informationDrag Race Roll Bar (MMRB-6, -7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Drag Race Roll Bar (MMRB-6, -7) The Maximum Motorsports 6-point Drag Race
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationInstallation Instructions
DODGE 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2230 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More information11221 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: CHEVROLET MODEL: VOLT STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationframe bracket
, Rev 4 02/19 frame bracket 8552012 Chevrolet & GMC ITEM PART # QTY DESCRIPTION 1 00248 4 WASHER,.625 LOCK 2 00253 2 NUT,.75 HEX 3 00254 2 WASHER,.75 LOCK 4 00477 4 WASHER,.625 FLAT 5 00492 2 WASHER,.75
More informationComfort Ride Shock absorber system part numbers 2450, 2460 and 2470 Installation Instructions
Comfort Ride Shock absorber system part numbers 2450, 2460 and 2470 Installation Instructions All specifications are subject to change without notice. MOUNTING FLANGE CENTER HOLE FRONT OF Item Qty Part
More informationCAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck
INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationDetroit Speed, Inc. Rear Coilover Tower Brace Kit Camaro P/N:
Detroit Speed, Inc. Rear Coilover Tower Brace Kit 2016+ Camaro P/N: 042433 The Detroit Speed, Inc. 2016+ Camaro Rear Coilover Tower Brace Kit is a bolt-in design that increases overall vehicle stiffness.
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationInstallation Guide. Stowe Cargo Management System. Table of Contents
Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages
More informationCustom 3-Point Seatbelt Installation Guide for: Mustang
Custom 3-Point Seatbelt Installation Guide for: 1965-1973 Mustang Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:
More informationTOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation
Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationChevy Tahoe. Replacement Seat/ Chevy Tahoe Installation Instructions. Questions? us at
LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Replacement Seat/2015-2018 Chevy Tahoe CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING
More informationADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12
Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**
60660 SUBKIT 7/8/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 500 / 3500 SHORT AND LONG BED PAGE OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN & HDX GRILLE GUARD APPLICATION: 2015 & UP Ford F-150 PART NUMBER: 40-3835, 45-3830, 57-3830, 57-3835 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill Installation Instructions Short & Long Bed All Megacabs 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION WARNING: Under
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationDate: Order No.: Supersedes: Group:
Installation Instructions Date: April 2007 Order No.: Supersedes: P-I-82.60/394A Group: 82 Revision: MOST ring configuration correction Section F, Figure 17 SUBJECT: MODEL 220.170/174/175/176/183/184 MODEL
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SPEED CABLE SHIFTER units built before 4/30/12
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 6 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2"-
More informationAL625 & AL625HD INSTALLATION & OWNER S MANUAL
AL625 & AL625HD INSTALLATION & OWNER S MANUAL These instructions are provided to assist you in the installation of the AL625. If you require further assistance, our trained staff is ready to provide you
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationFig & MOUNTING RAIL INSTALLATION KIT
16100 & 16200 MOUNTING RAIL INSTALLATION KIT 09/28/06 CUSTOM MOUNTING BRACKETS REQUIRED ON SOME INSTALLATIONS DEALER/INSTALLER: 1) Provide this manual to end user. 2) Physically demonstrate procedure in
More informationStowe Cargo Management System
Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages
More information5.5 Wheel drive (wheel pilots only)
Chapter 5: Installing the ST4000+ 61 5.5 Wheel drive (wheel pilots only) The Raymarine wheel drive will fit 3, 4, 5, 6, 7 or 8 spoke wheels. It is designed to operate with steering systems with between
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SP.
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fixed Bracket Bed Extender Titan (2016-) Bed Extender (999T7 W4100) Installation of this accessory requires installation of
More informationCOVER PAGE BASE RAIL MOUNTING KIT 10 BOLT RAIL KIT NOTE!
COVER PAGE 30035 BASE RAIL MOUNTING KIT 10 BOLT RAIL KIT NOTE! If you have a newer model year truck you must go to one our websites for the most recent updated instructions. www.reeseproducts.com or www.draw-tite.com
More informationPFadvantage Metalfor Araus 1360
Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134
More informationINSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370
INSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370 USE EXTREME CAUTION WHEN DRILLING ON ANY VEHICLE. MAKE SURE THAT ALL FUEL LINES, BRAKE LINES, ELECTRICAL
More informationLAND ROVER DISCOVERY 3/ SPARE WHEEL CARRIER
LAND ROVER DISCOVERY 3/ 4 SPARE WHEEL CARRIER RBLD007 INSTALL TIME: 4.5 Hours NOTE: Park Distance Control will be affected by this fitment and the customer should be informed. IMPORTANT WARNING! IT IS
More informationINSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT
INSTALLATION INSTRUCTIONS C-DMM-123 2013-2018 FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are sold separately. See
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: ¾, 7/8, 15/16 Drill Bits: 1/8, 9/16, 5/8 1-1/8 HOLE SAW Other Tools: Center Punch, Measuring Tape Installation Instructions 5 WARNING: Under no circumstances
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE
TITAN pt. no.: 02 0000 0180 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE 30 Gallon* Spare Tire Auxiliary Fuel
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE
TITAN pt. no.: 03 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE 30 Gallon* Spare Tire Auxiliary Fuel
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More information13102 INSTALLATION INSTRUCTIONS
1310 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 010-PRESENT MAKE: MERCEDES BENZ MODEL: ML350 BlueTEC, GL350 BlueTEC AWD, GL50, & GL550 STYLE:
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473664 F:620.869.9031 Custom 5th Wheel Hitch Mounting Rail Installation Instructions
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationInstallation Instructions
Installation Instructions DODGE RAM (1/2 TON AND 3/4 TON) 2002 2008 1500 PICK UP TRUCK 2003 2012 2500 PICK UP TRUCK (Except Megacab) Part Numbers: 50040 Parts List Qty A 1 B 1 C 2 D 2 E 2 F 2 Description
More information2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE.
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6 OVAL STEPS UNIVERSAL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationCAUTION: Do not install damaged parts!!!
Your satisfaction is important to us, please let us help! If you have any questions or concerns during the installation, our support representatives are available to assist you. Please call: 1-877-769-3765
More informationKinze 3000 Series Row Unit. Hydraulic Actuator Installation Instructions PN: ENG REV. A
Kinze 3000 Series Row Unit Hydraulic Actuator PN: 2006428-ENG REV. A Installation Overview Required Parts Part Number Qty * Description 4003011 1 HYDRAULIC ACTUATOR ASSY. (INCLUDES MOUNTING HARDWARE) 4003458
More informationK9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers
More information