ILLUSTRATED PARTS LIST

Transcription

1 Art s-way Manufacturing Co., Inc. CattleMaxx Grinder/Mixer Models 5105 And 5165 Illustrated Parts List ILLUSTRATED PARTS LIST Issued

2 This symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. The message that follows the symbol contains important information about your safety. Carefully read the message. Make sure you fully understand the causes of possible injury or death. IF THIS MACHINE IS USED BY AN EMPLOYEE, IS LOANED, OR IS RENTED, MAKE SURE THAT THE OPERATOR UNDERSTANDS THE TWO INSTRUCTIONS BELOW. BEFORE THE OPERATOR STARTS THE ENGINE: 1. GIVE INSTRUCTIONS TO THE OPERATOR ON SAFE AND CORRECT USE OF THE MACHINE. 2. MAKE SURE THE OPERATOR READS AND UNDERSTANDS THE OPERATOR S MANUAL FOR THIS MACHINE. WARNING IMPROPER OPERATION OF THIS MACHINE CAN CAUSE INJURY OR DEATH. BEFORE STARTING THE ENGINE, DO THE FOLLOWING: 1. READ THE OPERATOR S MANUAL. 2. READ ALL SAFETY DECALS ON THE MACHINE. 3. CLEAR THE AREA OF OTHER PERSONS. LEARN AND PRACTICE SAFE USE OF MACHINE CONTROLS IN A SAFE AND CLEAR AREA BEFORE YOU OPERATE THIS MACHINE ON A JOB SITE. It is your responsibility to observe pertinent laws and regulations and to follow manufacturer s instructions on machine operation and maintenance. See your Authorized Art s-way Manufacturing Co., Inc. dealer or Art s-way Manufacturing Co., Inc. for additional operator s manuals, illustrated parts catalogs, and service manuals.

3 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST TO THE OWNER 1 TO THE OWNER Congratulations on the purchase of your new Art s-way CattleMaxx. You have selected a top quality machine that is designed and built with pride to ensure you have many years of efficient and reliable service. Many people have worked on the design, production, and delivery of this CattleMaxx. The information in this manual is based on the knowledge, study, and experience through years of specializing in the manufacturing of farm machinery. This manual is designed to provide you with important information regarding safety, maintenance, and machine operation so you can and will get the best possible performance from your CattleMaxx. Even if you are an experienced operator of this or similar equipment, we ask that you read this manual before operating this CattleMaxx. The way you operate, adjust, and maintain this unit will have much to do with its successful performance. Any further questions you may have about this product of Art s-way equipment should be directed to your local Art s-way dealer or to Art s-way Manufacturing Co., Inc., Armstrong, Iowa, 50514, (712) SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE Art s-way Manufacturing Co., Inc. is continually making product improvements. In doing so, we reserve the right to make changes and/or add improvements to our products without obligation for the equipment previously sold. Modifications to this CattleMaxx may affect the performance, function, and safety of its operation. Therefore, no modification are to be made without the written permission of Art s-way Manufacturing Co., Inc. Any modification made without the written permission of Art s-way Mfg. Co. shall void the warranty of this product. In the interest of continued safe operation of this CattleMaxx, pay particular attention to the safety alert symbol(s) throughout this manual. ART S-WAY MANUFACTURING CO., INC. STATEMENT OF PRODUCT LIABILITY Art s-way Manufacturing Co., Inc. recognizes its responsibility to provide customers with a safe and efficient product. Art s-way Manufacturing Co., attempts to design and manufacture its products in accordance with all accepted engineering practices effective at the date of design. This statement should not be interpreted to mean that our products will protect against the user s own carelessness or failure to follow common safety practices nor will Art s-way Manufacturing Co., be liable for any such act. In addition, Art s-way Manufacturing Co., assumes no liability for any altered product or any modified product by users or anyone other than an authorized dealer. IMPORTANT WARRANTY INFORMATION The warranty for this CattleMaxx appears on page 4 of this manual. In order to establish proper warranty registration, the Warranty Registration must be completed and returned to the factory. Failure to comply with this requirement may result in reduced warranty allowances. LIMITATIONS OF THIS MANUAL This manual contains operating instructions for your CattleMaxx only. Any mention of other machinery in this manual other than the CattleMaxx is for reference only. This manual does not replace nor is it to be used for any machinery that may be attached to or used in conjunction with the CattleMaxx. ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

4 2 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST PARTS & SERVICE PARTS & SERVICE As the purchaser of your new CattleMaxx, it is very important to consider the following factors: A. Original Quality B. Availability of Service Parts C. Availability of Adequate Service Facilities Art s-way Manufacturing Co., Inc. has an excellent dealership network ready to answer any questions you may have about your CattleMaxx. Parts for your machine may be ordered through our dealers. When placing a parts order, please have the model and serial number ready. This will allow the dealer to fill your order as quickly as possible. For your convenience, we have provided this space for you to record your model number, serial number, and the date of purchase, as well as your dealer s name and address. Owner s Name: Owner s Address: Purchase Date: Dealership Name: Dealership Address: Dealership Phone No.: CattleMaxx Serial Number Location The placard containing the serial and model number is located on the front left-hand side of the CattleMaxx. Enter the serial and model number of your CattleMaxx within the space provided. Figure 1 Serial and Model Placard Location Figure 2 Serial Model Number Placard Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

5 5105 GRINDER / MIXER ILLUSTRATED PARTS LIST TABLE OF CONTENTS 3 TABLE OF CONTENTS TO THE OWNER... 1 SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE...1 ART S-WAY MANUFACTURING CO., INC. STATEMENT OF PRODUCT LIABILITY...1 IMPORTANT WARRANTY INFORMATION...1 LIMITATIONS OF THIS MANUAL...1 PARTS & SERVICE... 2 TABLE OF CONTENTS... 3 LIMITED WARRANTY... 4 SAFETY FIRST... 5 NOTICES OF DANGER, WARNING, AND CAUTION...5 SAFETY GUIDELINES... 6 BEFORE OPERATING...6 DURING OPERATION...6 MAINTENANCE SAFETY...6 HYDRAULIC SAFETY...6 TRANSPORTATION SAFETY...7 STORAGE SAFETY...7 TIRE SAFETY...7 ASSEMBLY SAFETY...7 ILLUSTRATED PARTS LIST... 8 ALPHANUMERIC INDEX...8 DRIVELINE ASSEMBLY (540 RPM) JACK ASSEMBLY TANK ASSEMBLY MIXING AUGER ASSEMBLY GEARBOX ASSEMBLY, MIXER DRIVE AND GEARBOX ASSEMBLY, LOWER SPINDLE, HITCH, AND HUB ASSEMBLY (5105 ONLY) SPINDLE, HITCH, AND HUB ASSEMBLY (5165 ONLY) MILL TO MIXER AUGER ASSEMBLY SUPPLEMENT HOPPER HOPPER AND DRIVE ASSEMBLY, DISCHARGE MECHANICAL SWIVAL, DISK DRIVE SWIVEL ASSEMBLY, HYDRAULIC INCH MECHANICAL VERTICAL OR HYDRAULIC DISCHARGE ASSEMBLY (5105 ONLY) INCH VERTICAL DISCHARGE ASSEMBLY OLD DESIGN (5165 ONLY) INCH VERTICAL DISCHARGE ASSEMBLY NEW DESIGN (5165 ONLY) INNER ELBOW ASSEMBLY, DISCHARGE (5105) INNER ELBOW ASSEMBLY, DISCHARGE (5165) MECHANICAL RING AND WORM GEAR ASSEMBLY (5105) HYDRAULIC DISCHARGE LIFT ASSEMBLY (5105) HYDRAULIC DISCHARGE LIFT ASSEMBLY (5165) ROLLERMILL, BASIC 20 INCH ROLLERMILL BELT DRIVE - 20 INCH INCH ROLLERMILL DRIVE ASSEMBLY (540 RPM) INCH ROLLERMILL WITH OFFSET HOPPER DRIVE ROLL ASSEMBLY IDLER (ECCENTRIC) ROLL ASSEMBLY INCH ROLLERMILL, BASIC (5165 ONLY) INCH ROLLERMILL BELT DRIVE (5165 ONLY) RPM 30 INCH ROLLERMILL DRIVE ASSEMBLY (5165 ONLY) INCH ROLLERMILL ASSEMBLY WITH OFFSET HOPPER (5165 ONLY) NEW OR REGROOVED 30 INCH ROLLS (5165 ONLY) COVER ASSEMBLY FOR OFFSET HOPPER WITHOUT AUGER FEEDER AUGER FEEDER ASSEMBLY, ROLLERMILL FOLDING DISCHARGE AUGER EXTENSION 3 AND 6 FEET BOLT-ON DISCHARGE AUGER EXTENSION 3 AND 6 FEET HYDRAULIC PLUMBING - LIFT AND SWING WITH HYDRAULIC AUGER FEEDER HYDRAULIC PLUMBING - LIFT AND SWING WITHOUT HYDRAULIC AUGER FEEDER HYDRAULIC MOTOR KITS VALVE ASSEMBLY, HYDRAULIC FLOW CONTROL ELECTRONIC SCALE ASSEMBLY SCALE ARM ASSEMBLY PAINT AND DECALS ART S-WAY MANUFACTURING COMPANY Manual No (May 2007)

6 4 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST LIMITED WARRANTY LIMITED WARRANTY Art s-way Manufacturing Co., Inc. warrants the products it sells to be free from defects in material and workmanship for a period of one (1) year after the date of delivery to the first (original) purchaser, subject to the following conditions: Art s-way Manufacturing Co., Inc. obligation and liability under this warranty is to repair or replace (at the company s option) any parts that upon manufacture were defective in material or workmanship. All parts and repairs under this warranty shall be supplied at Art s-way Manufacturing Co., Inc. or an authorized Art s-way Manufacturing Co., Inc. dealer, at the option of Art s-way Manufacturing Co., Inc. Art s-way Manufacturing Co., Inc. warranty does not extend to parts and elements not manufactured by Art s-way Manufacturing Co., Inc. and which carry the warranty of other manufacturers. Transportation or shipping to an authorized dealer for necessary repairs is at the expense of the purchaser. Art s-way Manufacturing Co., Inc. makes no other warranty expressed or implied and makes no warranty of merchantability or fitness for any particular purpose beyond that expressly stated in this warranty. Art s- Way Manufacturing Co., Inc. liability is limited to the terms set forth in this warranty and does not include any liability for direct, indirect, incidental or consequential damages or expenses of delay and the company s liability is limited to repair or replacement of defective parts as set forth herein. Any improper use and/or maintenance, including operation after discovery of defective or worn parts, operation beyond the rated capacity, substitution of parts not approved by Art s-way Manufacturing Co., Inc., or any alternation or repair by other than an authorized Art s-way Manufacturing Co., Inc. dealer which affects the product materially and adversely, shall void the warranty. No dealer, employee or representative is authorized to change this warranty in any way or grant any other warranty unless such change is made in writing and signed by an officer of Art s-way Manufacturing Co., Inc. Some states do not allow limitations on how long an implied warranty lasts or exclusions of, or limitations on relief such as incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you the specific legal rights and you may have other rights that vary from state to state. Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

7 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SAFETY FIRST 5 SAFETY FIRST A careful operator is the best insurance against an accident (National Safety Council) Most accidents can be prevented if the operator: Fully understands how the machine functions Can anticipate situations which may produce problems Can make necessary corrections before problems develop Figure 3 - Universal Safety Alert Symbol THIS SYMBOL MEANS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The American Society of Agricultural Engineers has adopted the Universal Safety Alert Symbol as a way to identify areas of potential danger if the equipment is not operated correctly. (See Figure 4.) Please be alert whenever you see this symbol in the manuals or on your grinder/mixer. Art s-way Manufacturing Co., Inc. strives to make our equipment as safe as possible. The Art s-way 5105 Grinder/Mixer conforms to applicable safety standards at the time of manufacturing. A safety conscious equipment operator makes an effective accident-prevention program complete. Safety features and instructions for the harvester are detailed in the Safety Guidelines section of this Operator s Manual. It is the responsibility of the owner to ensure that all operators read and understand the manual before they are allowed to operate the grinder/mixer. (Occupational Safety and Health Administration (OSHA) regulations ) NOTICES OF DANGER, WARNING, AND CAUTION Signal Words: Note the use of signal words DANGER, WARNING, and CAUTION on the grinder/mixer and in this manual. The appropriate signal word for each has been selected using the following guidelines: DANGER: IMMEDIATE AND SPECIFIC HAZARD WHICH WILL RESULT IN SEVERE PERSONAL INJURY OR DEATH IF PROPER PRECAUTIONS ARE NOT TAKEN. WARNING: SPECIFIC HAZARD OR UNSAFE PRACTICE COULD RESULT IN SEVERE PERSONAL INJURY OR DEATH IF PROPER PRECAUTIONS ARE NOT TAKEN. CAUTION: A REMINDER OF GOOD SAFETY PRACTICES. PERSONAL INJURY COULD RESULT IF PROPER PROCEDURES ARE NOT FOLLOWED. ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

8 6 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SAFETY GUIDELINES SAFETY GUIDELINES Remember: The Best Operator is a Safe Operator CAUTION: READ AND UNDERSTAND THE OPERATOR S MANUAL AND ALL THE SAFETY DECALS BEFORE OPERATING THE GRINDER MIXER. REVIEW ALL SAFETY INSTRUCTIONS WITH ALL OPERATORS ANNUALLY. BEFORE OPERATING Do not wear loose fitting clothing as it may catch in moving parts. Make sure to install and/or secure all guards, doors and shields, including the tractor power take-off (PTO) master shield, before starting or operating the Grinder Mixer. Be sure that the correct implement driveline parts are used and that they are properly secured. Install the safety chain when attaching the Grinder Mixer to the tractor. Clear the area of bystanders, especially children, when making repairs, adjustments or performing maintenance on the Grinder Mixer. Do not allow riders. Put all tractor and machine controls in neutral and disengage the PTO before starting. Follow the starting instructions according to your tractor Manual. Operate the Grinder Mixer only while seated on the tractor seat. Make sure the unit is adequately supported with safety blocks or safety stands when changing tires or performing maintenance. CAUTION: KEEP WELL CLEAR OF MOVING PARTS. BE SURE TO SHUT OFF THE TRACTOR AND SET THE PARKING BRAKE. REMOVE THE TRACTOR KEY WHILE MAKING ANY ADJUSTMENTS. WAIT FOR ALL MOVEMENT TO STOP BEFORE APPROACHING THE MACHINE. DURING OPERATION Keep hands, feet, hair, and clothing away from moving parts. Keep all guards, doors and shields in place and in good working condition. Keep all bystanders, especially children, away from the grinder mixer while in operation. Do not allow riders while the grinder mixer is in operation. Do not attempt to unclog, clean, or adjust the grinder mixer while it is running. Stay away from overhead power lines. Electrocution can occur even without direct contact. Keep all hydraulic lines, fittings, and couplers tight and free of leaks. (Refer to - Hydraulic Safety.) Use caution when ascending or descending on the grinder mixer. Wet shoes or boots are slippery. MAINTENANCE SAFETY Follow all operating, maintenance and safety instructions found in this Manual. Before servicing, adjusting, repairing or unclogging the machine, always make sure the tractor engine is stopped, the parking brake is set, and all the moving parts have stopped. Use sufficient tools, jacks, and hoists that have the capacity for the job. Use support blocks or safety stands when changing tires or performing maintenance. Follow good shop practices of keeping the service area clean and dry and use adequate light for the job at hand. Before applying pressure to the hydraulic system, make sure all lines, fittings and couplers are tightly secured and in good condition. Make sure all guards, doors and shields are in place and properly secured when performing maintenance. HYDRAULIC SAFETY Make sure components in the hydraulic system are kept clean and in good working condition. Relieve pressure from the hydraulic system before servicing or disconnecting from the tractor. Keep all hydraulic lines, fittings, and couplers tightly secured and free of leaks. Replace any worn, cut, abraded, flattened or crimpled hoses. Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

9 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SAFETY GUIDELINES 7 Do not make any temporary repairs to the hydraulic lines, fittings or hoses using tape, clamps, or cement. The hydraulic system operates under extremely high pressure and temporary repairs may fail suddenly and create a hazardous and or dangerous situation. Wear proper hand and eye protection when searching for a high-pressure hydraulic leak. Use a piece of wood or cardboard as a backstop instead of hands to identify and isolate a leak. If injured by a concentrated high-pressure stream of hydraulic fluid, seek medical attention immediately. Serious infection or toxic reaction can develop if hydraulic fluid penetrates the surface of the skin. Before applying pressure to the system, make sure all components are tight and that the hydraulic lines, hoses, and couplings are not damaged. TRANSPORTATION SAFETY Make sure the grinder mixer complies with all local regulations regarding the transportation of equipment on public roads and highways. Make sure the Slow Moving Vehicle (SMV) emblem and all lights and reflectors required by local highway and transportation authorities are properly in place, clean, and clearly visible to traffic. Do not allow riders on any machinery during transport. Make sure the grinder mixer is securely attached to the tractor and install a safety chain to the grinder mixer. Make sure the tractor brake pedals are latched together. Do not exceed 20 mph (32 km/h) when transporting the grinder mixer. Always reduce speed on rough roads and surfaces, or when going down inclines. Use caution when turning and always use the turn signals on the tractor to indicate your turning intentions to the other traffic. The weight of the trailed machine should NEVER exceed the weight of the towing vehicle. Check all clearances carefully whenever the machine is towed. Lower the elevator into the transport position before transporting the grinder/mixer on the highway. Stay away from overhead obstructions and power lines during transport. Electrocution can occur even without direct contact. STORAGE SAFETY Store the grinder mixer in an area away from human activity. Do not permit children to play on or around the stored machine at any time. Make sure that the grinder mixer is stored in an area with a firm and level base to prevent the machine from tipping or sinking into the ground. Block the wheels to prevent the machine from rolling. TIRE SAFETY Have only a qualified tire dealer or tire repair service perform tire repairs. Do not attempt to install a tire on a wheel or rim unless you have the proper equipment and experience to do the job. Follow proper procedures when installing a tire on a wheel or rim to prevent an explosion that could result in serious injury. Do not substitute tires with a lesser road rating and/or capacity for the original equipment tires. CAUTION: FAILURE TO FOLLOW PROPER PROCEDURES WHEN INSTALLING A TIRE ON A WHEEL OR RIM CAN PRODUCE AN EXPLOSION THAT MAY RESULT IN SERIOUS INJURY OR DEATH. DO NOT ATTEMPT TO INSTALL A TIRE UNLESS YOU HAVE THE PROPER EQUIPMENT AND EXPERIENCE TO PERFORM THE JOB. REPLACEMENT, REPAIR, AND/OR MAINTENANCE SHOULD BE DONE BY A QUALIFIED TIRE DEALER OR QUALIFIED REPAIR SERVICE. ASSEMBLY SAFETY Use adequate manpower to perform assembly procedures safely. Assemble the grinder mixer in an area with sufficient space to maneuver the largest components and allow easy access to all sides of the machine. Use only forklifts, lift cranes, jacks and tools with sufficient capacity for the loads. Do not allow spectators, especially children, in the working area. Remember: The Best Operator is a Safe Operator ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

10 8 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST ILLUSTRATED PARTS LIST The figure item corresponds to the number shown in the illustration. Figure items having a dash - next to the number indicates that the figure item is not displayed on the corresponding illustration. Numbers listed in the part number column are the numbers under which the parts are manufactured and by which the parts are identified by the manufacturer. Requirement shown in the Units Per Assy column is per Harvester or assembly. Items that have no specified quantity are designated by the letters AR (as required). RF listed in the Units Per Assy column indicates that the item is listed as a reference and the requirement is listed in another figure of the IPC. The relationship of component parts of an installation or assembly may be determined by the degree of indenture in the nomenclature column. The next higher assembly can be found by referring to the first indentation above and to the left. The following example shows the format of this indented system: * * * * DETAIL PART OR ASSEMBLY * DETAIL PART BREAKDOWN OR ASSEMBLY BREAKDOWN * * ADDITIONAL BREAKDOWN OF DETAIL PART OR ASSEMBLY * * * ADDITIONAL BREAKDOWN OF DETAIL PART OR ASSEMBLY ALPHANUMERIC INDEX , , , , , , 23, , 21, , , , 27, , , , , , , , , 41, , , Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

11 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST , , , 70, , , 35, , , , , 23, , , , , , , , , , ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

12 10 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST , , 33, 35, 37, , , , , , , , , , , , , , P P P P P P P P P P , 53 P P P P P P P P P P P P P30800M...63 P P Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

13 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 11 P P P P P P P P P P P P P P P P P P P P P , 59 P , 61 P , 59 P P ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

14 12 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST DRIVELINE ASSEMBLY (540 RPM) DRIVELINE ASSEMBLY (540 RPM) (374140) (380690) USED ON 20 INCH ROLLERMILL RF USED ON 30 INCH ROLLERMILL RF YOKE, 1-3/8 INCH 6 SPLINE A S KIT, CROSS AND BEARING PIN, SPRING 10 X YOKE, INBOARD SHAFT, INNER PROFILE S PROFILE AND SLEEVE W.A YOKE, INBOARD SHEARBOLT, CLUTCH 1 N/A SHEARBOLT, CLUTCH N/A SHIELD, CONE 7 RIB TUBE, OUTER SHIELD OVL 1 N/A TUBE, OUTER SHIELD OVL N/A TUBE, INNER SHIELD RND RING, SC 25 BEARING CHAIN, SAFETY SCREW, SHIELD (IN 9) DECAL, DANGER ROTATING DRIVE LINE DECAL BEARING, SUPPORT ZERK, 3/16 DRIVE GREASE (IN 6) COLLAR, REINFORCED ASSEMBLY, COLLAR KIT (IN 1) BOLT, HHCS 3/8-16 X 2-1/ E NUT, LOCK 3/ PIN, CLEVIS PIN, COTTER IMPLEMENT DRIVELINE, IMPLEMENT HALF 1 N/A IMPLEMENT DRIVELINE, IMPLEMENT HALF N/A IMPLEMENT DRIVELINE, TRACTOR HALF 1 N/A IMPLEMENT DRIVELINE, TRACTOR HALF N/A 1 - = Not Illustrated Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

15 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 13 JACK ASSEMBLY JACK ASSEMBLY (5105) (5165) RING, RETAINING, BRACKET, SWIVEL TUBE AND BRACKET ASSEMBLY KIT, CRANK HANDLE ASSEMBLY KIT, THRUST WASHER ASSEMBLY PLUNGER ASSEMBLY TUBE ASSEMBLY, 14 INCH INNER SHAFT EXTENSION N/A 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

16 14 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST TANK ASSEMBLY Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

17 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 15 TANK ASSEMBLY TANK ASSEMBLY (5105) (5165) NUT, 5/16 LOCK WASHER, 5/16 FLAT SPRING, COMPRESSION BRACKET, LID LOCKING BOLT, HHCS 5/16 X 2-1/ BOLT, HHCS 5/16 X 3/ LID AND HINGE WELDMENT SEAL, TANK LID GRIP, RED HANDLE ECCENTRIC WELD E BOLT, HHCS 1/4 X 2-1/ WASHER, 1/4 FLAT NUT, 3/8 LOCK J03H1558 BOLT, CRG. 3/8 X 1-1/ LADDER WELD ASSEMBLY (5105) 1 N/A LADDER WELD ASSEMBLY (5165) N/A BOLT, CRG. 3/8 X STRIP, SEALING DOOR, CLEAN OUT NUT, WING 5/ PIN, COTTER 3/32 X COVER WLDT., TROUGH PIN, HINGE RUBBER ADHESIVE 5.0 OZ AR AR RUBBER, WINDOW FRAME WINDOW, GLASS DOOR, UNLOADING SLIDE BOLT, CRG. 5/16 X 3/ HANDLE, DOOR WASHER, LOCK 5/ NUT, 5/16 HEX HOLDER, SLIDING DOOR NUT, 1/4 LOCK BOLT, HHCS 1/4 X 3/ SPRING, SLIDE HOLDER ASSY HOLDER, PTO BOLT, HHCS 1/2-13 X 1-1/ NUT, LOCK 1/2-13 GR5 ZN NYLON FRAME AND TANK WLDT., 105 BU PORTABLE 1 N/A FRAME AND TANK WLDT., 165 BU PORTABLE N/A BRACKET, SHORT 105 BU 1 N/A BRACKET, LONG 165 BU N/A WASHER, LOCK 5/16 INCH NUT, HEX 5/16 INCH BRACKET, TUBE MOUNT CLAMP, HOSE TUBE, MANUAL HOLDER A MANUAL, IPL CATTLEMAX 5105/5165 GM B MANUAL, OPERATORS CATTLEMAX 5105/5165 GM COVER, AIR = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

18 16 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST MIXING AUGER ASSEMBLY MIXING AUGER ASSEMBLY (5105) (5165) BOLT, CRG. 1/2-13 X 2.0 GR5 ZN NUT, HEX 1/2-13 GR5 ZN BOLT, HHCS 3/8-16 X 1-1/2 GR SUPPORT, MAIN AUGER TUBE ROD, MIX AUGER TUBE WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X NUT, HEX 3/8-16 GR5 ZN HANGER, BEARING BEARING, PB 1-5/8 CI HSG. W/ LC BOLT, CRG. 3/8-16 X 1-1/4 GR AUGER WLDT., MIXING 105 BU (5105) 1 N/A AUGER WLDT., MIXING 165 BU (5165) N/A TUBE, MIXING AUGER 105 BU (5105) 1 N/A TUBE, MIXING AUGER 165 BU (5165) N/A WASHER, FLAT 1/2 STD WASHER, LOCK 1/ PADDLE, MIXING AUGER NUT, LOCK 3/8-16 HEX FLG = Not Illustrated Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

19 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 17 GEARBOX ASSEMBLY, MIXER GEARBOX ASSEMBLY, MIXER PLATE, BEARING PROTECTOR NUT, LOCK 1/2 GR5 ZN BEARING, FLANGE 1-5/8 INCH WASHER, FLAT 1.65 X 2.12 X KEY SQ. 5/16 X WASHER, FLAT 1.65 X 2.12 X GEAR, BEVEL 1-5/ WASHER, SPECIAL LOCK WASHER, BOLT LOCK BOLT, HHCS 1/2 X GEARBOX, MACHINED, A WASHER, 1.44 X 2.25 X I PIN, COTTER 1/8 X 1-1/ PLUG, PIPE 3/ BEARING, BALL, 1-7/16 CYL SHAFT, GEARBOX 1.44 X BOLT, HHCS 1/2 X 2.25 G5 ZN GASKET, GEARBOX COVER, GEARBOX WASHER, LOCK 5/16 ZN BOLT, HHCS 5/16 X 0.75 G5 ZN WASHER, FLAT 1-21/32 X 2.0 X 9/ RING, RETAINING INTERNAL GEARBOX, W/ BEARINGS PERMATEX ULTRA BLUE 13 OZ. AR W GEAR OIL SAE AR - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

20 18 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST DRIVE AND GEARBOX ASSEMBLY, LOWER Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

21 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 19 DRIVE AND GEARBOX ASSEMBLY, LOWER DRIVE AND GEARBOX ASSEMBLY, LOWER GEARBOX ASSY., 5165 GM SPROCKET, 60B14 COUPLER CHAIN ASSY., P INC. CONN SPROCKET, 60B ID KEY, SQ. 3/8 X 2.O 4 6 I486454R1 SHIM, INCH BLADE CHAIN, ROLLER 2040 X 33P WASHER, FLAT X 1.38 X ZN WASHER, LOCK 1/2 INCH ZN NUT, HEX 1/2-13 GR5 ZN SHAFT, MIXER DRIVE NUT, HEX LOCK 1/4-20 GA CZ SCREW, AHSS 5/16-18 X 0.31 PL HUB WLDT., SHEAR BORE PLATE, SPROCKET 40A28 1-5/8 ID BOLT, HHCS 1/4-20 X 1.0 GR HUB WLDT., SHEAR ID BOLT, HHCS 1/4-20 X 1-1/2 GR SPROCKET, PLATE 80A RING, RETAINING BEARING, 1-5/8 PB, CI HSG W/ LC BOLT, CRG. 1/2-13 X 2.0 GR BOLT, CRG. 3/8-16 X 2-3/4 GR BRACKET, MILL TO MIXER IDLER TIGHTENER, CHAIN WASHER, FLAT X 1.0 X WASHER, LOCK 3/8 INCH NUT, HEX 3/8-16 GR SPROCKET, 40B BORE KEY, PAR, 5/16 SQ. X V BOLT, CRG. 1/2-13 X 1-1/4 GR5 2 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

22 20 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SPINDLE, HITCH, AND HUB ASSEMBLY (5105 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

23 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 21 SPINDLE, HITCH, AND HUB ASSEMBLY (5105 ONLY) SPINDLE, HITCH, AND HUB ASSEMBLY - STANDARD SPINDLE, HITCH, AND HUB ASSEMBLY SCALE (366400) (366380) CLEVIS, 1-7/8 HITCH BAR, HITCH W/O SCALE N/A 1 2A HITCH, /8 INCH CAL 5 PIN 1 N/A WASHER, LOCK 1 INCH NUT, HEX 1 INCH BOLT, HHCS 3/4 X 4.50 G5 ZN WASHER, LOCK 3/ NUT, HEX 3/ CONE, BRG BOLT, STUD 1/2-20 X CUP, BRG NUT, LUG 1/2-20 UNF CUP, BEARING HUB ASSEMBLY 6-BOLT CONE, BRG WASHER, FLAT 0.81 X 1.75 X NUT, SLOTTED HEX 3/ PIN, COTTER 5/32 X CAP, HUB 2.50 INCH TIRE, TUBELESS 10 X 15 8 PLY WHEEL, 8 X 15 6-BOLT GOLD VALVE STEM, W/ CORE AND CAP BOLT, HHCS 1/2 X 4.50 G5 ZN WASHER, LOCK 1/ NUT, HEX 1/ SPINDLE, 2.12 X N/A 2 25A SPINDLE, WEIGHTBAR 2 N/A BOLT, HHCS 1/2 X 1.25 G5 ZN BRACKET, MOUNTING 105 BU FENDER, 105 BU BOLT, CRG. 1/2 X 1.0 G5 ZN WASHER, FLAT 0.56 X 1.38 X CHAIN, SAFETY 5 FT JACK ASSEMBLY 151 DS COMPLETE CONNECTOR, POWER CORD 1 N/A CORD, 23 FT. DIGITAL POWER 1 N/A TIE, NYLON CABLE 14 N/A MOUNT, 4-WAY CABLE 4 N/A - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

24 22 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SPINDLE, HITCH, AND HUB ASSEMBLY (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

25 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 23 SPINDLE, HITCH, AND HUB ASSEMBLY (5165 ONLY) SPINDLE, HITCH, AND HUB ASSEMBLY - STANDARD SPINDLE, HITCH, AND HUB ASSEMBLY SCALE (366410) (366390) CLEVIS, 1-7/8 HITCH BAR, HITCH W/O SCALE N/A 1 2A BAR, HITCH W/ SCALE 1 N/A WASHER, LOCK 1 INCH NUT, HEX 1 INCH BOLT, HHCS 3/4 X 4.50 G5 ZN WASHER, LOCK 3/ NUT, HEX 3/ SEAL, 2.12 X 3.06 X CONE, BRG ID CUP, BRG BOLT, LUG 9/16 X 1.12 UNF CUP, BEARING HUB ASSEMBLY CONE, BRG WASHER, FLAT 0.81 X 1.75 X NUT, SLOTTED HEX 3/ PIN, COTTER 5/32 X CAP, HUB 2.50 INCH TIRE, 13.5 X WHEEL, 11 X VALVE STEM, W/ CORE AND CAP BOLT, HHCS 1/2 X 4.50 G5 ZN WASHER, LOCK 1/ NUT, HEX 1/ SPINDLE, 2.12 X N/A 2 25A WEIGHTBAR, 2-1/8 DIA. X PIN AXLE 2 N/A BOLT, HHCS 1/2 X 1.25 G5 ZN BRACKET, MOUNTING FENDER, 150 BU BOLT, CRG. 1/2 X 1.0 G5 ZN WASHER, FLAT 0.56 X 1.38 X SUPPORT, FENDER BOLT, CRG. 1/2 X 1.25 G5 ZN CHAIN, SAFETY 5 FT JACK ASSEMBLY 151 DS COMPLETE CONNECTOR, POWER CORD 1 N/A CORD, 23 FT. DIGITAL POWER 1 N/A TIE, NYLON CABLE 14 N/A MOUNT, 4-WAY CABLE 4 N/A - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

26 24 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST MILL TO MIXER AUGER ASSEMBLY MILL TO MIXER AUGER ASSEMBLY RF WASHER, FLAT X 1.38 X ZN NUT, HEX 1/2-13 GR5 ZN WASHER, LOCK 1/2 INCH ZN BOLT, CRG. 1/2-13 X 1.0 SSN GR5 ZN FLANGE, 1.12 BRG 3-BOLT ROUND NUT, HEX FLG. LK 5/ WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X ZN NUT, HEX 3/8-16 GR5 ZN BOLT, CRG. 1/2-13 X 1.25 SSN GR5 ZN BEARING, 1.12 SOD SPRING LOCK PLATE, HOLE COVER BRACKET WLDT., BEARING HOLDER BEARING, 1.12 SPLIT WOOD PB BOLT, CRG. 5/16-18 X 0.50 SSN GR2 ZN BOLT, CRG. 3/8-16 X 1.0 SSN GR5 ZN AUGER WLDT., MILL TO MIXER TROUGH, LOWER PAN TO TANK PAN WLDT., LOWER COVER, LOWER PAN CAP, TROUGH PLATE, CAP CAP, ANGLE CAULKING, TUBE MAGIC SEAL CLEAR AR - = Not Illustrated Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

27 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 25 SUPPLEMENT HOPPER SUPPLEMENT HOPPER BOLT, HHCS 5/16-18 X 0.62 GR5 ZN FLANGETTE, BRG BOLT RD NUT, LOCK 3/8-16 HEX FLG. GR NUT, LOCK 5/16-18 HEX FLG. G PIN, COTTER 5/32 X 1.0 CHISEL PIN, COTTER 3/32 X 1.0 ZN PIN, CLEVIS 3/8 X 2.25 GR5 ZN WASHER, FLAT X X ZN BOLT, HHCS 5/16-18 X 1.5 GR5 ZN BEARING, 1.12 SOD SPRING LOCK LID WLDT., SUPPLEMENT HOPPER PLATE, HOLE COVER CUTTER, SACK GRATE, SUPPLEMENT HOPPER BOLT, CRG. 5/16-18 X 0.50 SSN GR BOLT, CRG. 3/8-16 X 1.0 SSN GR HOPPER WLDT., SUPPLEMENT COVER, SUPPLEMENT HOPPER AUGER WLDT., CONCENTRAT TANK GRATE, ANGLED HOPPER 1 21 I669184R1 CLAMP, SHIELD LATCH 1 22 I SCREW, PHMS X 1/ WASHER, LOCK # NUT, HEX = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

28 26 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST HOPPER AND DRIVE ASSEMBLY, DISCHARGE HOPPER AND DRIVE ASSEMBLY, DISCHARGE 1 I486454R1 SHIM, BLADE WASHER, FLAT X 1.38 X ZN NUT, HEX 1/2-13 GR5 ZN WASHER, LOCK 1/2 INCH ZN BOLT, HHCS 3/8-16 X 1.25 GR5 ZN NUT, WING 5/ BOLT, HHCS 5/16-18 X 0.75 GR5 ZN BOLT, HHCS 3/8-16 X 1.0 GR5 ZN 1 - = NOT ILLUSTRATED Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

29 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 27 HOPPER AND DRIVE ASSEMBLY, DISCHARGE HOPPER AND DRIVE ASSEMBLY, DISCHARGE (CONT) BOLT, CRG. 5/16-18 X 0.75 GR5 ZN DOOR, CLEANOUT BOLT, CRG. 1/2-13 X 2 GR5 ZN FLANGE, 1.12 BRG. 3-BOLT RND NUT, LOCK 3/8-16 FLNG. HX GR NUT, 5/16-18 HX FLNG. LK. GR5 ZN SPROCKET, 40B28, 1.12 BORE GEAR, BEVEL 14T 1.25 BORE WASHER, FLAT 1.14 X 1.62 X PLN PIN, COTTER 5/32 X 1.0 CHSL. PNT WASHER 1.14 X 1.62 X PLN KEY, PAR 5/16 SQ. X WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X SPRING, CLUTCH HOLDING BEARING., 1.25 PB, STL. HSG. W/ LC GRIP, CLUTCH HANDLE KEY, PAR, 5/16 SQ. X FLANGETTE., 1.12 BRG. 2-BOLT SPROCKET, 40B24, 1.25 BORE WASHER, FLAT 0.38 X 0.88 X NUT, LOCK 3/8-16 DSTHD WASHER, FLAT X 0.75 X 16 GA. ZN NUT, LOCK 1/4 INCH HEX FLNG NUT, HEX 7/16-14 GR2 ZN NUT, HEX 3/8-16 GR5 ZN CLUTCH, A-66 CASTING 1-1/ I WASHER, 1.28 X 2.00 X PLN BOLT, CRG. 3/8-16 X 1.25 GR RING, 1.25 SNAP SCREW, 1/4-20 X 0.75 TR HD, GR2 ZN FEED DEFLECTOR PIN, CLEVIS 3/8 X 2.38 ZN CLUTCH, A-67 CASTING 1-1/ HANDLE, CLUTCH BEARING, 1.12 SOD SPRING LOCK SHIELD, LOWER GEARS SPACER, 1/2 INCH LONG SPACER, 7/8 INCH LONG FORK, DISCHARGE CLUTCH CHAIN ASSY., RC40 X 61P ROD, CLUTCH, ARM WLDT., CLUTCH AUGER WLDT., PUSH SHAFT, BACK AUGER DRIVE 1-1/ TIGHTENER, CHAIN GRATE, DISCHARGE COVER WLDT., BACK HOPPER SHIELD, PUSH AUGER SPACER, BEARING GASKET, FILLER BOLT, CRG. 3/8-16 X 1.0 GR5 ZN STRIP, SEAL, DISCHARGE CO DISCHARGE WLDT., FIRST SECT BOLT, CRG. 3/8-16 x 2.25 GR2 ZN 1 64 JN71292 BOLT, HXHD 5/16-18 X 1/2 FLG. GR BEARING, 1.25 SOD SPRING LOCK 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

30 28 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST MECHANICAL SWIVAL, DISK DRIVE Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

31 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 29 MECHANICAL SWIVAL, DISK DRIVE MECHANICAL SWIVAL, DISK DRIVE I WASHER, FLAT X 1.06 X ZN 2 2 I14994R1 BOLT, CRG. 5/16-18 X 1.0 NK GR BOLT, HHCS 5/16-18 X 1.0 GR5 ZN FLANGETTE, BEARING 2-BOLT BOLT, HHCS 5/16-18 X 0.75 GR5 ZN BOLT, CRG. 5/16-18 X 0.75 GR5 ZN CRANK ASSEMBLY, BACK AUGER PIN, EXPANSION 3/16 X BEARING, 1/2 INCH BALL, SPECIAL NUT, HEX FLNG. LOCK 3/ NUT, HEX FLNG. LOCK 5/ GRIP, PLASTIC BEARING, 3/4 INCH ADAPTER, SOD WASHER, LOCK, 5/16 INCH ZN NUT, HEX 5/16-18 GR5 ZN NUT, LOCK 5/16-18 HEX DSTHD BOLT, HHCS 5/16-18 X 4.5 GR5 ZN PIN, COTTER 1/8 X PIN, SPRING 1/4 X 1.38 SLOTTED BOLT, CRG. 3/8-16 X 1.0 GR5 ZN HANDLE, BRAKE YOKE, BRAKE BAND WLDT., HANDLE HALF BAND WLDT., PLAIN HALF DISK, HALF SWIVEL DRIVE SHAFT, SWIVEL DRIVE SPROCKET, 50B8, 3/4 INCH BORE RING HALF WLDT., DISK DRIVE BRACKET WLDT., MECH. SWING ROD, IDLER WLDT. 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

32 30 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST SWIVEL ASSEMBLY, HYDRAULIC Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

33 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 31 SWIVEL ASSEMBLY, HYDRAULIC SWIVEL ASSEMBLY, HYDRAULIC 1 I WASHER, FLAT 3/8 SAE. 8 2 I WASHER, FLAT 1/2 SAE NUT, HEX 1/ BOLT, HHCS 5/16-18 X KEY, WOODRUFF 1/4 X NUT, WING 5/ BOLT, HHCS 3/8-16 X BOLT, HHCS 3/8-16 X 3-1/ NUT, HEX FLG. LOCK 5/ WASHER, LOCK 3/ WASHER, FLAT 3/8 STD NUT, LOCK 3/8-16 DISTHRD WASHER, LOCK 5/ BOLT, HHCS 1/2-12 X SPROCKET ASSY., 60B CHAIN, RC60 60P BOLT, HHCS 3/8-16 X MOTOR, HYD 20 CU IN DISP SPROCKET, HALF 60A SPRING, COMP X 0.75 X PLATE, CLAMP SPACER, OD X ID X PLATE, SPROCKET BOLT HALF BAND ASSY, WIDE HALF SLIP SHIELD ASSY, SWIVEL MOTOR SCREW, SET 5/16-18 X 5/ = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

34 32 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 29 INCH MECHANICAL VERTICAL OR HYDRAULIC DISCHARGE ASSEMBLY (5105 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

35 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH MECHANICAL VERTICAL OR HYDRAULIC DISCHARGE ASSEMBLY (5105 ONLY) MECHANICAL VERTICAL OR HYDRAULIC DISCHARGE ASSEMBLY RF BOLT, HHCS 3/8-16 X 1.5 GR5 ZN 5 2A TUBE WLDT., 29 INCH VERTICAL MECHANICAL LIFT 1 2B TUBE WLDT., 29 INCH VERTICAL HYDRAULIC LIFT BOLT, HHCS 3/8-16 X 1.0 GR5 ZN BOLT, HHCS 3/8-16 X 3.0 GR5 ZN BEARING, BALL 1/2 INCH SPECIAL FLANGETTE, BRG BOLT RND NUT, LOCK 3/8-16 HEX FLG. GR GEAR, BEVEL 14T 1.25 INCH BORE WASHER, FLAT 1.25 X 1.75 X ZN WASHER, FLAT 1.25 X 1.75 X ZN KEY, SQ. 5/16 X 1.12 LG BRACKET, SWIVEL RING WASHER, FLAT X 1.0 X ZN NUT, LOCK 3/8-16 FIN. HEX GRA CLAMP WLDT., HEAVY SWIVEL AUGER WLDT., VERT. DISCH. 29 INCH RING, 1.25 SNAP SPACER, 3/8 X 1/2 X 5/16 LONG RING, SWIVEL BRACKET, SWIVEL RING ATTACH BEARING, 1.25 SOD ZERK, 1/4-28 TAPER DR. THREAD WASHER, LOCK 3/ WASHER, FLAT 13/32 X 1.75 X 9/ BOLT, CRG. 3/8-16 X 1 SSN WASHER, FLAT 1-1/4 X 3/ RING, FLANGETTE REINFORCING 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

36 34 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 52 INCH VERTICAL DISCHARGE ASSEMBLY OLD DESIGN (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

37 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH VERTICAL DISCHARGE ASSEMBLY OLD DESIGN (5165 ONLY) INCH VERTICAL DISCHARGE ASSEMBLY OLD DESIGN (5165 ONLY) PER ASSY BOLT, HHCS 3/8-16 X 1.5 GR5 ZN BOLT, HHCS 5/16-18 X 0.75 GR5 ZN BOLT, HHCS 3/8-16 X 1.0 GR5 ZN BOLT, HHCS 3/8-16 X 3.0 GR5 ZN BEARING, BALL 1/2 INCH SPECIAL FLANGETTE, BRG BOLT RND NUT, LOCK 3/8-16 HEX FLG. GR GEAR, BEVEL 14T 1.25 INCH BORE WASHER, FLAT 1.25 X 1.75 X ZN WASHER, FLAT 1.25 X 1.75 X ZN KEY, SQ. 5/16 X 1.12 LG BRACKET, SWIVEL RING WASHER, FLAT X 1.0 X ZN NUT, LOCK 3/8-16 FIN. HEX GRA WASHER, LOCK 5/16 INCH ZN NUT, HEX 5/16-18 GR RING, 1.25 SNAP SPACER, 3/8 X 1/2 X 5/16 LONG RING, SWIVEL BRACKET, SWIVEL RING ATTACH BEARING, 1.25 SOD ZERK, 1/4-28 TAPER DR. THREAD AUGER WLDT., VERT. DISCHARGE CLAMP WLDT., HEAVY SWIVEL TUBE WLDT., 18 INCH LOWER VERTICAL TUBE WLDT., 16 INCH VERTICAL WASHER, LOCK 3/ WASHER, FLAT 13/32 X 1.75 X 9/ BOLT, CRG. 3/8-16 X 1.0 SSN WASHER, FLAT 1-1/4 X 3/ RING, FLANGETTE REINFORCING TUBE WLDT., 18 INCH UPPER VERTICAL 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

38 36 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 52 INCH VERTICAL DISCHARGE ASSEMBLY NEW DESIGN (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

39 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH VERTICAL DISCHARGE ASSEMBLY NEW DESIGN (5165 ONLY) INCH VERTICAL DISCHARGE ASSEMBLY NEW DESIGN (5165 ONLY) PER ASSY BOLT, HHCS 3/8-16 X 1.5 GR5 ZN BOLT, HHCS 5/16-18 X 0.75 GR5 ZN BOLT, HHCS 3/8-16 X 1.0 GR5 ZN BOLT, HHCS 3/8-16 X 3.0 GR5 ZN BEARING, BALL 1/2 INCH SPECIAL FLANGETTE, BRG BOLT RND NUT, LOCK 3/8-16 HEX FLG. GR GEAR, BEVEL 14T 1.25 INCH BORE WASHER, FLAT 1.25 X 1.75 X ZN WASHER, FLAT 1.25 X 1.75 X ZN KEY, SQ. 5/16 X 1.12 LG BRACKET, SWIVEL RING WASHER, FLAT X 1.0 X ZN NUT, LOCK 3/8-16 FIN. HEX GRA WASHER, LOCK 5/16 INCH ZN NUT, HEX 5/16-18 GR RING, 1.25 SNAP SPACER, 3/8 X 1/2 X 5/16 LONG RING, SWIVEL BRACKET, SWIVEL RING ATTACH BEARING, 1.25 SOD ZERK, 1/4-28 TAPER DR. THREAD AUGER WLDT., VERT. DISCHARGE CLAMP WLDT., HEAVY SWIVEL TUBE WLDT., 52 INCH TUBE WLDT., 16 INCH VERTICAL WASHER, LOCK 3/ WASHER, FLAT 13/32 X 1.75 X 9/ BOLT, CRG. 3/8-16 X 1.0 SSN WASHER, FLAT 1-1/4 X 3/ RING, FLANGETTE REINFORCING 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

40 38 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INNER ELBOW ASSEMBLY, DISCHARGE (5105) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

41 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 39 INNER ELBOW ASSEMBLY, DISCHARGE (5105) INNER ELBOW ASSEMBLY, DISCHARGE (5105) RF 1 I WASHER, FLAT X X NUT, WING 5/ BOLT, HHCS 5/16-18 X 0.75 GR5 ZN DOOR, CLEANOUT FLANGE, 1-1/8 BRG. 3-BOLT RND NUT, HEX FLG. LK. 3/ GEAR, BEVEL, 14T, 1-1/4 BORE WASHER, FLAT 1.25 X 1.75 X WASHER, FLAT 1.25 X 1.75 X KEY, PAR, 5/16 SQ. X WASHER, LOCK 3/8 INCH BOLT, HHCS 3/8-16 X 0.75 GR5 ZN WASHER, FLAT 0.38 X 0.88 X WASHER, LOCK, 5/16 ZN NUT, HEX 5/16-18 GR5 ZN RING, 1.25 SNAP AUGER WLDT., TILTED RH FLIGHT 7 INCH X BEARING, 1.25 SOD SPRING LOCK ELBOW ASSEMBLY, LIGHT HOOD ASSY, DISCHARGE AUGER AUGER WLDT., TILTED RH FLIGHT 7 INCH X INCH BOLT, CRG. 3/8-16 X 1.0 GR5 ZN STRIP, SEAL, DISCHARGE CO TUBE WLDT., 8 X 103 X 16 GA ELBOW WLDT., 105 INNER COVER, GEAR ANCHOR WLDT., BEARING BRACKET, 105 BOLT ON EXT NUT, HEX 1/2-13 GR5 ZN WASHER, LOCK 1/2 INCH HOLDER WLDT., UNLOADING BOLT, CRG. 1/2-13 X 1.0 SSN GR5 ZN WRAP, DISCHARGE BOLT, HHCS 5/16-18 X 1-1/ SHIELD, BEVEL GEAR RING, 1.12 SNAP HOOD, WLDT DOOR, DISCHARGE HOOD SPRING BOLT, HHCS 5/16 X 5/ NUT, HEX 5/16-18 LOCK 2 42 I669184R1 CLAMP 2 43 I SCREW, PHMS #10-24 X 1/ W WASHER, #10 FLAT WASHER, #10 LOCK NUT, #10-24 HEX 4 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

42 40 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INNER ELBOW ASSEMBLY, DISCHARGE (5165) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

43 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 41 INNER ELBOW ASSEMBLY, DISCHARGE (5165) PER ASSY INNER ELBOW ASSEMBLY, DISCHARGE (5165) RF 1 I WASHER, FLAT X X NUT, WING 5/ BOLT, HHCS 5/16-18 X 0.75 GR5 ZN DOOR, CLEANOUT FLANGE, 1-1/8 BRG. 3-BOLT RND NUT, HEX FLG. LK. 3/ GEAR, BEVEL, 14T, 1-1/4 BORE WASHER, FLAT X 1.75 X WASHER, FLAT X 1.75 X KEY, PAR, 5/16 SQ. X WASHER, LOCK 3/8 INCH BOLT, HHCS 3/8-16 X 0.75 GR5 ZN WASHER, FLAT 0.38 X 0.88 X WASHER, LOCK, 5/16 ZN NUT, HEX 5/16-18 GR5 ZN RING, 1.25 SNAP AUGER WLDT., TILTED RH FLIGHT 7 INCH X BEARING, 1.25 SOD SPRING LOCK ELBOW ASSEMBLY, LIGHT HOOD ASSY, DISCHARGE AUGER AUGER WLDT., TILTED RH FLIGHT 7 INCH X BOLT, CRG. 3/8-16 X 1.0 GR5 ZN STRIP, SEAL, DISCHARGE CO TUBE WLDT., 8 X 103 X 16 GA ELBOW WLDT., 150 INNER COVER, GEAR ANCHOR WLDT., BEARING BRACKET, 150 BOLT ON EXT NUT, HEX 1/2-13 GR5 ZN WASHER, LOCK 1/2 INCH HOLDER WLDT., UNLOADING BOLT, CRG. 1/2-13 X 1.0 SSN GR5 ZN WRAP, DISCHARGE BOLT, HHCS 5/16-18 X 1-1/ SHIELD, BEVEL GEAR RING, 1.12 SNAP HOOD WLDT DOOR, DISCHARGE HOOD SPRING BOLT, HHCS 5/16 X 5/ NUT, HEX 5/16-18 LOCK 2 42 I669184R1 CLAMP 2 43 I SCREW, PHMS #10-24 X 1/ W WASHER, #10 FLAT WASHER, #10 LOCK NUT, #10-24 HEX 4 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

44 42 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST MECHANICAL RING AND WORM GEAR ASSEMBLY (5105) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

45 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 43 MECHANICAL RING AND WORM GEAR ASSEMBLY (5105) MECHANICAL RING AND WORM GEAR ASSEMBLY (5105) RF BOLT, HHCS 3/8-16 X WASHER, FLAT 3/8 INCH BRACKET, LIFT ASSIST SPRING SPACER, INCH X INCH WASHER, LOCK 3/8 INCH NUT, HEX 3/8-16 INCH CHANNEL, LEVER BRACE BOLT, CRG. 5/16-18 X 1.0 INCH NUT, HEX FLANGE LOCK 5/16-18 X 1.0 INCH LEVER, LIFT BOLT, HHCS 5/16-18 X 3/4 INCH WASHER, LOCK 5/16 INCH BOLT, HHCS 5/16-18 X 1.0 INCH WASHER, FLAT 5/16 INCH NUT, HEX 5/16-18 INCH CHAIN, 2/0 SAFETY SPRING EXTENSION RING, RETAINING ZERK, 1/ GEAR, RING W/ 10 HOLES RING AND WORM HOLDER SPROCKET, 40B18 3/4 INCH BORE PIN, EXPANSION 1/4 X 2.0 INCH PLATE, HOLDER CUP, BEARING CONE, BEARING 3/4 INCH BORE WORM AND SHAFT PIN, EXPANSION 1/4 X 1-1/4 INCH BOLT, HHCS 3/8-16 X 1-1/2 INCH CHAIN, ROLLER #40 X 144 PITCHES PIN, SAFETY 1/8 X 4-3/8 INCH SPROCKET, 40B9 5/8 INCH BORE PIN, EXPANSION 3/16 X 1-1/4 INCH BRACKET WLDT., LIFT ASSIST PM WASHER, FLAT 21/32 INCH SHAFT, LIFT ASSIST CRANK PIN, EXPANSION 3/16 X 1.0 INCH PLATE ASSY, ADJUSTMENT CRANK WLDT GRIP, PLASTIC 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

46 44 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST HYDRAULIC DISCHARGE LIFT ASSEMBLY (5105) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

47 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 45 HYDRAULIC DISCHARGE LIFT ASSEMBLY (5105) HYDRAULIC DISCHARGE LIFT ASSEMBLY (5105) RF CYL., HYD., 3 X 16 CLEVIS, 1-1/ SEAL KIT, CROSS (1-1/4 DIA. ROD) (IC4629) SEAL KIT, PRINCE (1-3/8 DIA. ROD) (PMCK-BF-0520) END WLDT., BALL ID MOUNT WLDT., LOWER CYL ARM WLDT., VERT. CYL. MNT LEVER, CYL. LIFT CHANNEL, BRACE HYD. LIFT BRACKET, BRACE SWING STOP HOLDER, HYD. LIFT DISCHARGE RING, RETAINING FITTING, 1/4-28 STR I472790R2 STUD, NUT, AND LOCK WASHER 1 12 V PIN, LYNCH BOLT, HHCS 5/16-18 X 1-1/ BOLT, HHCS 5/16-18 X 3/ BOLT, CRG. 5/16-18 X 1-1/ WASHER, LOCK 5/ NUT, HEX 5/ WASHER, FLAT 5/16 STD I C1 BUSHING, 1.25 OD X 1.00 ID X I PIN, CLEVIS 1.0 X 3.0 ZN PIN, BRIDGE 3/16 INCH INTERNAL STOP, SWING BOLT, HHCS 5/8-11 X I NUT, HEX 5/ WASHER, LOCK 5/ BOLT, HHCS 5/8-11 X I WASHER, FLAT 1-1/8 X 2-1/4 X PLATE, SUPPORT CYL. ARM PLATE, SPACER CYL. ARM BOLT, HHCS 1/2-13 X 1-1/ NUT, HEX 1/ WASHER, LOCK 1/ HOLDER, WLDT., RING HOSE BOLT, HHCS 1/4-20 X NUT, HEX 1/ WASHER, LOCK 1/ WASHER, FLAT 1/4 STD. 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

48 46 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST HYDRAULIC DISCHARGE LIFT ASSEMBLY (5165) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

49 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 47 HYDRAULIC DISCHARGE LIFT ASSEMBLY (5165) HYDRAULIC DISCHARGE LIFT ASSEMBLY (5165) RF CYL., HYD., 3 X 16 CLEVIS, 1-1/ SEAL KIT, CROSS (1-1/4 DIA. ROD) (IC4629) SEAL KIT, PRINCE (1-3/8 DIA. ROD) (PMCK-BF-0520) END WLDT., BALL ID MOUNT WLDT., LOWER CYL ARM WLDT., VERT. CYL. MNT LEVER, CYL. LIFT CHANNEL, BRACE 7.0 X BRACKET, BRACE BOTTOM HOLDER, HYD. LIFT DISCHARGE RING, RETAINING FITTING, 1/4-28 STR I472790R2 STUD, NUT, AND LOCK WASHER 1 12 V PIN, LYNCH BOLT, HHCS 5/16-18 X 1-1/ BOLT, HHCS 5/16-18 X 3/ BOLT, CRG. 5/16-18 X 1-1/ WASHER, LOCK 5/ NUT, HEX 5/ WASHER, FLAT 5/16 STD I C1 BUSHING, 1.25 OD X 1.00 ID X I PIN, CLEVIS 1.0 X 3.0 ZN PIN, BRIDGE 3/16 INCH INTERNAL STOP, SWING BOLT, HHCS 5/8-11 X I NUT, HEX 5/ WASHER, LOCK 5/ BOLT, HHCS 5/8-11 X I WASHER, FLAT 1-1/8 X 2-1/4 X PLATE, SUPPORT CYL. ARM PLATE, SPACER CYL. ARM BOLT, HHCS 1/2-13 X 1-1/ NUT, HEX 1/ WASHER, LOCK 1/2 4 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

50 48 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST ROLLERMILL, BASIC 20 INCH Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

51 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 49 ROLLERMILL, BASIC 20 INCH ROLLERMILL, BASIC 20 INCH NUT, HEX JAM 7/8-9 GR5 ZN 24 2 E NUT, SQ. 5/ P10010 FRAME ASSY, LH SIDE R/MILL 1 4 P10011 FRAME ASSY, RH SIDE R/MILL NUT, HEX JAM 1/2-13 GR5 ZN 2 6 P10182 PLUG, CLAMP SCREW 2 7 P10191 STOP, HANDLE HOUSING, LH ECCENTRIC BRG HOUSING, RH ECCENTRIC BRG P10580 POINTER 1 11 P20124 PANEL, ECCENTRIC END 1 12 P20126 PANEL, DRIVE ROLL END COVER 1 13 P20127 PLATE, INSPECTION COVER 1 14 P20128 PANEL, BASE COVER ROD, SPACER 7/8 X P20130 PLATE, FEED CONTROL BOX 1 17 P20134 PANEL, TOP COVER 1 18 P96213 ROD, SPACER 7/8 X P20170 HANDLE, ECCENTRIC ADJUSTING SHAFT, ECCENTRIC ROLL SHAFT, DRIVE ROLL 1 22 P20215 SPACER, ROLL BEARING BOLT, HHCS 5/8-11 X 6.0 GR5 ZN 2 24 P20270 AGITATOR ASSY, 20 INCH ROLLER M BOLT, HHCS 1/4-20 X 0.50 GR5 ZN 1 26 P96936 SPRING, COMPRESSION 4 27 P98341 SCREW, SLOT MACH. #10 X P98300 SCREW, AHSS 3/8 X P98408 KEY, FEATHER 0.25 X 0.25 X P98417 PIN, GROOVE 0.25 X BOLT, HHCS 1/2-13 X 1.0 GR5 ZN 2 32 P99000 BEARING, ROLL SHAFT 8 33 P73631 SCRAPER WLDT., 20 INCH DRIVE ROLL 1 34 P99040 BEARING, AGITATOR 0.75 BORE SL P99467 BOLT, HHCS 3/8 X 3.0 FULL THD SCREW, HH TAP. 5/16-18 X 3/4 SHEET METAL WASHER, 5/16 FLAT NUT, HEX 3/ P73612 SCRAPER WLDT., 20 INCH ECC. ROLL WRENCH, 20 INCH ROLLERMILL BOLT, HHCS 1/2-13 X 1-1/2 GR5 ZN ** NOTE ** WASHER, LOCK 1/2 ZN ** NOTE ** 8 NOTE: #41 AND #42 ARE INCLUDED IN #3 AND #4 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

52 50 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST ROLLERMILL BELT DRIVE - 20 INCH ROLLERMILL BELT DRIVE - 20 INCH (397390) (397630) :1 STANDARD DRIVE RF :1.12 DIFFERENTIAL DRIVE RF 1 E BUSHING, MACH 0.75 X 1.25 X 18 GA P10027 KEY SQ X P10481 BRACKET WLDT., TIGHTENER P10486 PIVOT WLDT., TIGHTENER P20220 PULLEY, ROLL DRIVE P20320 PULLEY, AGITATOR P98298 SCREW, AHSS 3/8-16 X P98375 SPRING, EXTENSION P98522 CHAIN, #1 X 8.0 LINKS STRGHT. CL P99025 PULLEY, IDLER 0.634B 4.37 OD P99712 BELT, ROLL DRIVE BB KEY SQ X WASHER, FLAT X 1.75 X ZN WASHER, LOCK 5/8 INCH ZN NUT, HEX 5/8-11 GR2 ZN PIN, COTTER 5/21 X 1.25 ZN BOLT, HHCS 5/8-11 X 3.75 GR5 ZN P10730 BELT GUARD, ROLLER MILL P30881 PULLEY, ROLL SPD. DIFF. N/A 1 - = Not Illustrated Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

53 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH ROLLERMILL DRIVE ASSEMBLY (540 RPM) INCH ROLLERMILL DRIVE ASSEMBLY (540 RPM) RF PTO ASSEMBLY, 1-3/8 X 1-3/ PIN, CLEVIS 5/16 X PIN, COTTER 1/8 X SHIELD WLDT BOLT, HHCS 1/4-20 X I404766R1 NUT, TINNERMAN J 1/ BRACKET, SHIELD MOUNTING KEY SQ. 1/4 X P99637 SPROCKET, 60B22 40MM SET SCREW, (INCLUDED IN #9) N/A CHAIN, RC60 76 PITCHES NUT, HEX 3/ WASHER, LOCK 3/ WASHER, FLAT 3/ TIGHTENER, CHAIN BRACKET, M-T-M IDLER BOLT, CRG. 3/8-16 X 2-1/ NUT, HEX 1/ WASHER, LOCK 1/ SPROCKET, IDLER 60A WASHER, FLAT 1/ BRACKET, IDLER 1 23 J03H1593 BOLT, CRG. 1/2-13 X 2-1/2 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

54 52 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 20 INCH ROLLERMILL WITH OFFSET HOPPER Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

55 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH ROLLERMILL WITH OFFSET HOPPER INCH ROLLERMILL WITH OFFSET HOPPER RF 1 E NUT, LOCK 3/8-16 HEX TOP GA, ZN 2 2 P10148 SCREW WLDT., SET 2 3 P10284 TUBE WLDT., HANDLE 1 4 P10730 GUARD WLDT., BELT 1 5 P10735 BRACKET, BELT GUARD 1 6 P20000 MILL, BASIC 20 INCH ROLLER 1 7 P20286 GATE WLDT., GRAIN 1 8 P82700 MAGNET ASSEMBLY, 20 INCH WASHER, FLAT X 1.38 X ZN WASHER, LOCK 1/2 INCH ZN BOLT, HHCS 3/8-16 X 1.25 GR5 ZN BOLT, HHCS 1/4-20 X 0.75 GR5 ZN NUT, LOCK 3/8-16 FLG. HEX GR WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X WASHER, FLAT 0.31 X 0.75 X 16 GA. ZN NUT, HEX 3/8-16 GR5 ZN NUT, HEX 1/4-20 GR5 ZN WASHER, LOCK 1/4 INCH NUT, HEX 5/16-18 GR5 ZN BOLT, HHCS 1/2-13 X 1.0 GR5 ZN BOLT, CRG. 3/8-16 X 0.75 GR5 ZN PLATE WLDT., ADAPTER HOPPER WLDT., OFFSET 20 INCH TROUGH WLDT., SAMPLE TUBE WLDT., LOWER PAN ROD SCREW, RHS 5/16-18 X NUT, HEX 1/2-13 GR5 ZN BOLT, CRG. 1/2-13 X 1.0 GR5 ZN GATE WLDT., 20 INCH ROLLERMILL LINK, LOWER TUBE WLDT., LINK PIN, EXPANSION 3/16 X 1.0 ZN GRIP, ROUND HANDLE LEVER WLDT., 20 INCH LIFT KNOB, FLUTED 5/ BOLT, CRG. 5/16-18 X 1-1/4 SSN BOLT, HHCS 3/8-16 X 3/ CAP, ANGLE PLATE, CAP 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

56 54 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST THIS PAGE LEFT INTENTIONALLY BLANK Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

57 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 55 DRIVE ROLL ASSEMBLY NEW REGROOVED ROLL ASSEMBLY, 5-GROOVE FLAT ROLL ASSEMBLY, 5-GROOVE SHARP ROLL ASSEMBLY, 7-GROOVE FLAT ROLL ASSEMBLY, 7-GROOVE SHARP ROLL ASSEMBLY, 10-GROOVE FLAT ROLL ASSEMBLY, 10-GROOVE SHARP ROLL ASSEMBLY, 12-GROOVE SHARP IDLER (ECCENTRIC) ROLL ASSEMBLY NEW REGROOVED DRIVE ROLL ASSEMBLY ROLL ASSEMBLY, 5-GROOVE FLAT ROLL ASSEMBLY, 5-GROOVE SHARP ROLL ASSEMBLY, 7-GROOVE FLAT ROLL ASSEMBLY, 7-GROOVE SHARP ROLL ASSEMBLY, 10-GROOVE FLAT ROLL ASSEMBLY, 10-GROOVE SHARP ROLL ASSEMBLY, 12-GROOVE SHARP - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

58 56 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 30 INCH ROLLERMILL, BASIC (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

59 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH ROLLERMILL, BASIC (5165 ONLY) MP30800M 30 INCH ROLLERMILL, BASIC (5165 ONLY) NUT, HEX 1/ P98341 SCREW, SPHMS #10-24 X 1/ SHAFT, ROLL ECCENTRIC 30 INCH 1 4 P30813 COVER, TOP FRONT CASTING 1 5 P30814 COVER, REAR TOP 1 6 P30815 COVER, FRONT AND REAR CASTING 2 7 P30816 PLATE, FEED CONTROL 1 8 P30820 SHAFT WLDT., AGITATOR SHAFT, 30 INCH PTO DRIVE 1 10 P30835 HANDLE WLDT., ECC ADJUSTING 1 11 P36810 SIDE ASSY., LH 1 12 P36811 SIDE ASSY., RH CHANNEL WLDT., RH CHANNEL WLDT., LH BRAKE WLDT., ADJUSTABLE RH 1 16 P36182 PLUG, CLAMP SCREW BRASS 2 17 P36196 WEIGHT WLDT., ROLL 4 18 P36824 HOUSING, DRIVE SIDE ECC P36825 HOUSING, ECCENTRIC 2 20 P36835 BRAKE WLDT., ADJUSTABLE LH 1 21 P36838 PLATE, ROLL ADJUSTER 2 22 P36852 STOP, CORN ROLL 1 23 P74358 BUSHING, SUPPORT SWIVEL 4 24 P97946 BUSHING, R2 X 3.0 SPLIT TAPER 4 25 P98307 SCREW, DOG POINT SS 1/2-13 X P98346 SCREW, HH SELF TAP 5/16 X 5/ BOLT, HHCS 3/8-16 X WASHER, LOCK 3/8 INCH 4 29 P99036 BEARING, 1.25 AGITATOR RB P99050 BEARING, SHAFT RS 4 31 P99420 BOLT, HHCS 7/8-9 X 6.50 GR5 ZN 2 32 P99530 NUT, SQ. 7/8-9 HEAVY NUT, JAM 1/2-13 GR5 ZN WASHER, FLAT X 1.38 X ZN WASHER, LOCK 1/2 INCH ZN BOLT, HHCS 1/2-13 X BOLT, 1/2-13 X 2.25 GR5 ZN STOP, ECCENTRIC ROLL GAUGE BOLT, HHCS 1/2-13 X 1.50 GR5 ZN 8 40 P30940 SCRAPER, 30 INCH ROLL BOLT, HHCS 1/2-13 X 2.0 GR5 ZN WRENCH, ROLLERMILL 4 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

60 58 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST THIS PAGE LEFT INTENTIONALLY BLANK Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

61 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH ROLLERMILL BELT DRIVE (5165 ONLY) INCH ROLLERMILL BELT DRIVE (5165 ONLY) (423970) (423990) :1 STANDARD DRIVE RF :1.12 DIFFERENTIAL DRIVE RF 1 E BUSHING, MACH 0.75 X 1.25 X 18 GA PULLEY, ROLL SPD. DIFF. N/A 1 3 P30953 TIGHTENER BRACKET P30957 SPRING, BRACKET PULLEY, ROLL DRIVE P30882 PULLY, AGITATOR P98298 SCREW, AHSS 3/8-16 X P98379 SPRING (V198-6) P36153 SHAFT, FULL THD P99025 PULLEY, IDLER 0.634B 4.37 OD P99712 BELT, ROLL DRIVE BB KEY SQ. 0.25X WASHER, FLAT X 1.75 X ZN PIN, COTTER 3/16 X 1-1/ NUT, HEX 5/8-11 GR2 ZN MOUNT WLDT., SHIELD P36731 GUARD WLDT., BELT P36735 BRACKET, REAR BOLT, HHCS 5/16-18 X WASHER, LOCK 5/16 ZN NUT, HEX 5/ E BUSHING, SPLIT TAPER Q1 2.0 X 1/4 X 1/ KEY SQ. 1/2 X 2-1/ SPACER, IDLER 1 N/A - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

62 60 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 540 RPM 30 INCH ROLLERMILL DRIVE ASSEMBLY (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

63 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST RPM 30 INCH ROLLERMILL DRIVE ASSEMBLY (5165 ONLY) RPM 30 INCH ROLLERMILL DRIVE ASSEMBLY RF 1 E10431O BRACKET, HOOK 1 2 E NUT, LOCK 3/8-16 HEX TOP GA 4 3 I SCREW, SET 3/8-16 X 0.38 GR8 ZN 4 4 P99637 SPROCKET, 60B22 40MM, 0.25 KEY WAY WASHER, FLAT X 1.38 X ZN NUT, HEX 1/2-13 GR5 ZN WASHER, LOCK 1/2 INCH ZN BOLT, CRG. 1/2-13 X 1.0 GR5 ZN SCREW, SET 5/16-18 X 0.31 AHSS KEY SQ. 1/4 X 1-1/ BOLT, HHCS 3/8-16 X 1.75 GR5 ZN WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X SPROCKET, IDLER 60A15 W/ BRG BOLT, HHCS 3/8-16 X 0.75 GR5 ZN NUT, HEX 3/8-16 GR5 ZN 1 17 E NUT, HEX TP LK 3/8-16 GA ZN BOLT, CRG. 1/2-13 X 1.25 SSN GR KEY, PAR 1/2 INCH SQ. X 2.75 HTTR PIN, COTTER 1/16 X 3/ NUT, HEX #10-24 GR2 ZN WASHER, LOCK # FLANGETTE., 1.62 AND 1.75 BRG., 4 BLT, RND BOLT, HHCS 1/2-13 X 5.0 GR5 ZN HOOK, RUBBER PIN, CLEVIS 1/4 X 1-5/8 ZN CHAIN, RC60-57 PITCHES BEARING, 1-3/4 X 85MM SOD, W/ COLLAR SHAFT SPROCKET, D 60B SPROCKET, D 60B SHIELD, FILLER SHIELD, MAIN MOUNT WLDT., MAIN DRIVE SPACER BLOCK, WOOD IDLER SHORT BLOCK, WOOD IDLER LONG CHAIN, RC PITCH BOLT, HHCS 1/2-13 X 3.0 GR5 ZN SCREW, #10-24 X 0.75 RHDHD, GR2 ZN BOLT, CRG. 1/2-13 X 2.0 GR5 ZN WASHER, FLAT 0.25 X 1.75 SQ. PLN WASHER, FLAT 0.38 X 1.75 SQ. PLN PTO ASSY, 1-3/8 6B X 1.75 SBC PIN, CELIVS 5/16 X 3.0 ZN PIN, COTTER 5/32 X 1.0 CHSL PNT BOLT, HHCS 3/8-16 X 2.25 GR5 ZN 2 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

64 62 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 30 INCH ROLLERMILL ASSEMBLY WITH OFFSET HOPPER (5165 ONLY) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

65 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST INCH ROLLERMILL ASSEMBLY WITH OFFSET HOPPER (5165 ONLY) INCH ROLLERMILL ASSEMBLY WITH OFFSET HOPPER RF BOLT, HHCS 5/16-18 X 3/ PANEL, 30 INCH UPPER MTG BOLT, TRUSS HD 1/4-20 X 3/ MAGNET NUT, HEX FLG. LOCK 1/ HOPPER WLDT., 30 INCH OFFSET NUT, HEX FLG. LOCK 5/ RUBBER, WINDOW FRAME GLASS, WINDOW WASHER, FLAT 1/4 STD PIN, COTTER 3/32 X 3/ GRATE WLDT., TRASH MAGNET ASSY, 30 INCH OFFSET COVER, AIR BOLT, HHCS 3/8-16 X 1-1/ WASHER, FLAT 3/8 STD P30800M 30 INCH ROLLER MIL BASE WLDT WASHER, FLAT 1/2 STD WASHER, LOCK 1/ BOLT, HHCS 1/2-13 X WASHER, LOCK 3/ NUT, HEX 3/ BOLT, CRG. 1/2-13 X 1-1/ E NUT, HEX TOP LOCK 3/ ROD, 3/8 X GRATE WLDT., 30 INCH LINK, LOWER TUBE WLDT., LINK BOLT, HHCS 3/8-16 X 3/ BOLT, CRG. 5/16-18 X 1-1/ HANGER WLDT., REAR HANGER WLDT., FRONT PIN, EXPANSION 3/16 X LEVER WLDT., LIFT KNOB, FLUTED 5/ GRIP, ROUND HANDLE NUT, HEX FLG. LOCK 3/ BOLT, CRG. 5/16-18 X 3/ NUT, HEX 5/ TROUGH, SAMPLE TUBE, WLDT SCREW, RHMS 5/16-18 X 3/ NUT, HEX 1/ BOLT, CRG. 3/8-16 X 3/4 6 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

66 64 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST NEW OR REGROOVED 30 INCH ROLLS (5165 ONLY) NEW REGROOVED ROLL ASSEMBLY, 5-GROOVE FLAT ROLL ASSEMBLY, 5-GROOVE SHARP ROLL ASSEMBLY, 7-GROOVE FLAT ROLL ASSEMBLY, 7-GROOVE SHARP ROLL ASSEMBLY, 10-GROOVE FLAT ROLL ASSEMBLY, 10-GROOVE SHARP ROLL ASSEMBLY, 12-GROOVE SHARP - = Not Illustrated]] Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

67 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 65 COVER ASSEMBLY FOR OFFSET HOPPER WITHOUT AUGER FEEDER (463230) (455110) COVER ASSEMBLY FOR OFFSET HOPPER WITHOUT AUGER RF RF FEEDER 1A COVER WLDT., W/O AUGER FEEDER 1 N/A 1B COVER WLDT., W/O AUGER FEEDER N/A BOLT, CRG. 5/16-18 X 0.62 GR NUT, LOCK 5/16-18 HEX FLG = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

68 66 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST AUGER FEEDER ASSEMBLY, ROLLERMILL (370260) 20 INCH (383890) 30 INCH AUGER FEEDER ASSEMBLY, ROLLERMILL RF RF NUT, LOCK 5/ HANDLE ASSY, BRAKE E CLIP, WIRE I14994R1 BOLT, CRG. 5/16-18 X 0.75 SQNK. GR I NUT, HEX LK. 1/2-13 GR5 CP JN CLAMP, HOSE SHORT WASHER, FLAT X 1.38 X ZN BOLT, HHCS 5/16-18 X 1.0 GR5 ZN ELBOW, 1/2 X 90 DEGREE STREET TEE, 1/2 INCH PIPE ZN BOLT, HHCS 1/2-13 X 2.5 GR5 ZN 1 1 Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

69 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 67 AUGER FEEDER ASSEMBLY, ROLLERMILL AUGER FEEDER ASSEMBLY, ROLLERMILL (CONT.) (370260) 20 INCH (383890) 30 INCH KEY, SQ. 1/4 X BOLT, HHCS 3/8-16 X 1.0 GR5 ZN WASHER, X 1.75 X 0.14 PLN COLLAR, 1.0 ECC. LOCK BEARING, 1.0 ADAPTER, SOD FLANGETTE, 7/8 X 1.0 BRG., 3-BOLT RND BOLT, CRG. 3/8-16 X 1.5 GR2 ZN SUPPORT, PIPE JACK TOP CLAMP, DRAG FEED ONL BOLT, HHCS 1/2-13 X 7.0 FULTHD MOTOR HYD., 12 CU. IN. DISPL BOLT, HHCS 1/2-13 X 1.5 GR5 ZN PIN, ROLL 1/4 X 1.75 ZN NUT, LOCK 5/16-18 HEX FLG WASHER, LOCK 3/8 INCH WASHER, FLAT X 1.0 X BOLT, HHCS 3/8-16 X 0.75 GR5 ZN NUT, LOCK 3/8-16 DISTHRD BOLT, HHCS 1/2-13 X 3.0 GR5 ZN NUT, HEX FLG. LK., 1/4 INCH NUT, HEX 3/8-16 GR5 ZN BOLT, HHCS 1/2-13 X 2.75 GR5 ZN BOLT, CRG. 5/16-18 X 1.0 GR2 ZN SPACER, ID X LG BOLT, CRG. 5/16-18 X 0.62 GR2 ZN PIN, HAIR COTTER 3/16 X BOLT, CRG 3/8-16 X 2.0 GR5 ZN HOSE, SINGLE BRAID 1/2 INCH HYD SPRING, EXT OD X 5.75 LG SPRING, 2 INCH DIA. X 14 INCH LG NUT, SPRING RETAINING E BOLT, CRG. 1/4-20 X ¾ ZN CABLE CLIP, 1/8 CABLE ADAPTER, CPLR FM. 1/2-14 NPTF TIE, NYLON CABLE COLLAR, SHAFT, ROLL FEED VALVE ASSY, HYD. FLOW CONTROL HOSE ASSY, 1/2 X 120 INCH HYDRAULIC FIT, HYD. NIPPLE 1/2 NPT HEX BOLT, CRG. 3/8-16 X 1.0 GR5 ZN ROPE, POLYPROPOLENE 102 INCH LG ROPE, WIRE ASSY, 124 INCH, MECH. AF PLATE, CLAMP A COVER WLDT., HOPPER 20 INCH 1 N/A 55B COVER WLDT., HOPPER 30 INCH N/A ANGLE, MOUNT PIPE, LOWER SUPPORT WLDT PIVOT WLDT BUSHING, 1.0 OD. X ID X HOUSING WLDT., AUGER FEEDER AUGER WLDT., GRAIN PANEL, HOPPER BEARING GUARD WLDT CAP WLDT., HOPPER STRAP, SPRING ADJUSTMENT STRAP, LOWER STRAP, SPRING EXTENSION FLAP, RUBBER GRAIN ROD, AUGER PIVOT BAND WLDT., CLAMP BAR, DECLUTCHER 1 1 ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

70 68 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST FOLDING DISCHARGE AUGER EXTENSION 3 AND 6 FEET FOLDING DISCHARGE AUGER EXTENSION 3 AND 6 FEET (528770) 3 FT (528780) 6 FT 1A FOOT EXTENSION TUBE 1 N/A 1B FOOT EXTENSION TUBE N/A 1 2A AUGER WLDT., TILTED 3 FT EXTENSION 1 N/A 2B AUGER WLDT., TILTED 6 FT EXTENSION N/A PIVOT WLDT., CLAMP-ON DECAL-AUGER ENGAGEMENT CLAMP BAND W/ STRAP CLAMP BAND W/ PIN PIVOT PIN COTTER PIN, 1/8 DIA. X NUT, HEX LOCK, 5/16 NC BOLT, HEX HD, 5/16 NC X 1-1/ LOCKING HANDLE AND PIVOT ASSY T-BAR HANDLE NUT, HEX 1/2 NC NUT, HEX LOCK, 1/2 NC BOLT, CARRIAGE, 5/16 NC X 3/ HAIRPIN, COTTER, 3/16 DIA. X CHAIN, 8 INCH LONG PIVOT DRIVE WLDT SET SCREW, SQ. HD 7/16 NC X 3/ HANGER WLDT., BEARING BEARING, PILLOW BLOCK, WOOD 1-1/ WASHER, FLAT 1-1/8 ID PIN, ROLL 1/4 DIA. X BOLT, HEX HD., 3/8 NC X 3/ NUT, FLANGE LOCK, 3/8 NC PLATE, BEARING MOUNT NUT, FLANGE LOCK, 5/16 NC MACHINE SCREW, TRUSS HD., 5/16 NC X 3/ HOOD ASSY, DISCHARGE AUGER FT. FOLDING DISCHARGE AUGER (NOT INCLUDED) FT. FOLDING DISCHARGE AUGER (NOT INCLUDED) Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

71 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 69 BOLT-ON DISCHARGE AUGER EXTENSION 3 AND 6 FEET BOLT-ON DISCHARGE AUGER EXTENSION 3 AND 6 FEET (528790) 3 FT (528800) 6 FT KIT, 3 FT. BOLT-ON EXTENSION, TILTED FLIGHTING RF KIT, 6 FT. BOLT-ON EXTENSION, TILTED FLIGHTING RF SET SCREW, 7/16 X 3/4 SQ. HD SHAFT, 1.1 X BAND, CLAMPING BOLT, 3/8 X 1-1/4 HHCS WASHER, 3/8 LOCK NUT, 3/8 HEX 7A AUGER, 3 FT EXTENSION 1 N/A 7B AUGER, 6 FT EXTENSION N/A 1 8A TUBE, 3 FT EXTENSION 1 N/A 8B TUBE, 6 FT EXTENSION N/A 1 - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

72 70 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST HYDRAULIC PLUMBING - LIFT AND SWING WITH HYDRAULIC AUGER FEEDER HYDRAULIC PLUMBING - LIFT AND SWING WITH HYDRAULIC AUGER FEEDER (5105) (5165) HOSE, HYDRAULIC 100R2 1/2 INCH X 144 INCH SAE HOSE, HYDRAULIC 100R2 1/2 INCH X 180 INCH SAE HOSE, HYDRAULIC 100R2 1/2 INCH X 120 INCH SAE ELBOW, MALE 1/2 X 3/8 X 90 DEGREE NPTF VALVE, DUAL RELIEF 800 PSI VALVE, FLOW CONTROL **NOTE** BUSHING, REDUCER 1/2 X 3/ ELBOW, STREET 1/2 X 90 DEGREE NPTF ADAPTER, 1/2 NPT-3/8 NPT ADAPTER, 1/ DEGREE STEEL STREET ELBOW A BRACKET, HYD. VALVES 1 N/A 11B PLATE, VALVE N/A BOLT, HHCS 5/16-18 X N/A BOLT, HHCS 5/16-18 X 2-1/ WASHER, FLAT 5/16 STD WASHER, LOCK 5/ NUT, HEX 5/ TIE, 3/16 X 11 CABLE A/R A/R VALVE, DOUBLE SELECTOR VALVE KIT, HANDLE VALVE KIT, SEAL DECAL, VALVE DIRECTION BOLT, HHCS 5/16-18 X = Not Illustrated NOTE: BOTH VALVES SHOULD BE SET TO THE SAME FLOW. UNEQUAL SETTINGS WILL CAUSE EXCESSIVE MOTOR AND CYLINDER BACK PRESSURE AND SHAFT SEAL FAILURE. Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

73 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 71 HYDRAULIC PLUMBING - LIFT AND SWING WITHOUT HYDRAULIC AUGER FEEDER HYDRAULIC PLUMBING - LIFT AND SWING WITHOUT HYDRAULIC AUGER FEEDER (5105) (5165) HOSE, HYDRAULIC 100R2 1/2 INCH X 144 INCH SAE HOSE, HYDRAULIC 100R2 1/2 INCH X 180 INCH SAE HOSE, HYDRAULIC 100R2 1/2 INCH X 120 INCH SAE ELBOW, MALE 1/2 X 3/8 X 90 DEGREE NPTF VALVE, DUAL RELIEF 800 PSI VALVE, FLOW CONTROL **NOTE** BUSHING, REDUCER 1/2 X 3/ ELBOW, STREET 1/2 X 90 DEGREE NPTF ADAPTER, 1/2 NPT-3/8 NPT ADAPTER, 1/ DEGREE STEEL STREET ELBOW A BRACKET, HYD. VALVES 1 N/A 11B PLATE, VALVE N/A BOLT, HHCS 5/16-18 X N/A BOLT, HHCS 5/16-18 X 2-1/ WASHER, FLAT 5/16 STD WASHER, LOCK 5/ NUT, HEX 5/ TIE, 3/16 X 11 CABLE ADAPTER, COUPLER FM 1/2-14 NPTF 2 2 NOTE: BOTH VALVES SHOULD BE SET TO THE SAME FLOW. UNEQUALI SETTINGS WILL CAUSE EXCESSIVE MOTOR AND CYLINDER BACK PRESSURE AND SHAFT SEAL FAILURE. ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

74 72 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST HYDRAULIC MOTOR KITS HYDRAULIC MOTOR KITS RF 1A MOTOR, HYDRAULIC (LIFT AND AUGER FEEDER) 1B MOTOR, HYDRAULIC (SWING) SEAL KIT, ROSS TRW ( AND ) SERIES MG #SK = Not Illustrated VALVE ASSEMBLY, HYDRAULIC FLOW CONTROL VALVE ASSEMBLY, HYDRAULIC FLOW CONTROL RF VALVE, FLOW CONTROL W/O HANDLE PIN, CLEVIS 3/8 X SPRING, X 0.5 X ZN LEVER WLDT., HYD., CONTROL 1 - = Not Illustrated Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

75 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 73 ELECTRONIC SCALE ASSEMBLY (5105) SCALE-CM ELECTRONIC SCALE ASSEMBLY RF RF (5165) 1A INDICATOR, MODEL CONNECTOR/5 PIN PLUG 1 1 1B INDICATOR, MODEL 640XL 3 CONNECTOR/5 PIN PLUG 1 1 1C INDICATOR, MODEL CONNECTOR/5 PIN PLUG 1 1 1D INDICATOR, MODEL 640M 3 CONNECTOR/5 PIN PLUG 1 1 2A SPINDLE, WEIGH BAR 5-PIN 2 N/A 2B SPINDLE, WEIGH BAR 5-PIN N/A HITCH, WEIGH BAR 5-PIN CLEVIS, HITCH 1-7/8 INCH BRACKET, INDICATOR NUT, LOCK 1/4-20 HEX FLANGE SCREW, TRUSS HEAD 1/4-20 X 1/ PLUG, 5-PIN PLUG (FOR 4 CONNECTOR INDICATORS) CLIP, SPRING BOLT, HHCS 3/4-10 X 4-1/ NUT, HEX 1-8 GRADE WASHER, LOCK 1 INCH SPLIT WASHER, LOCK 3/4 INCH SPLIT NUT, HEX 3/4-10 GRADE CONNECTOR, POWER CORD (FEMALE) CORD, 23 FT. DIGITAL POWER BRACKET LIGHT, WARNING DIGITAL HORN, DIGITAL WARNING TIE, NYLON CABLE 3/16 X BOX, BATTERY CLAMP, POSITIVE BATTERY CLAMP, NEGATIVE BATTERY ADAPTER, DUAL SPLICE KIT, WEIGH BAR CORD PIGTAIL, 5-PIN WITH B-CONNECTOR W/ 1 FT. CORD PIGTAIL, 5-PIN WITH B-CONNECTOR W/ 10 FT. CORD PIGTAIL, 5-PIN WITH B-CONNECTOR W/ 20 FT. CORD - = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

76 74 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST THIS PAGE LEFT INTENTIONALLY BLANK Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

77 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 75 SCALE ARM ASSEMBLY SCALE ARM ASSEMBLY RF ARM WLDT., SCALE PIVOT BRACKET, WLDT., SCALE PIVOT MNT BRACKET, WLDT., SCALE MTG BLOCK, PIVOT SPRING, COMPRESSION 1.0 X NUT, HEX SLOTTED 1/ I WASHER, FLAT 1/2 SAE WASHER, FLAT 1/2 STD. ZN 1 9 E BOLT, CRG. 1/2-13 X 1-1/ WASHER, LOCK 1/ NUT, HEX 1/ BOLT, HHCS 3/8-16 X 2 GR NUT, LOCK 3/8 HEX 2-WAY 2 14 I WASHER, FLAT 3/8 SAE ZERK, 1/4-28 TAPER DRIVE PIN, COTTER 5/32 X TIE, NYLON CABLE 3/16 X = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

78 76 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST PAINT AND DECALS Manual No (Jul 2007) ART S-WAY MANUFACTURING COMPANY

79 CATTLEMAXX 5105/5165 ILLUSTRATED PARTS LIST 77 PAINT AND DECALS PAINT AND DECALS (5105) (5165) TAG, SERIAL NO. FINISHED NAIL, 1/4 INCH GRIP TAPE, ANTI-SKID DECAL, GREASE SYMBOL DECAL, AUGER FEEDER STOP DECAL, START-STOP AUGER DECAL, VALVE DIRECTION DECAL, SUPPLEMENT INSTRUCTIONS DECAL, DANGER ROTATING DRIVE LINE P99897 DECAL, WARNING ROLLS, BELTS P99846 DECAL, ADJUSTING FEED FLOW DECAL, CAUTION SAFETY INSTRUCTIONS DECAL, CAUTION DO NOT OPEN DECAL, ATTENTION FOREIGN MATERIAL DECAL, CAUTION HITCH INSTRUCTIONS DECAL, DANGER AUGER FEEDER DECAL, DANGER ELECTROCUTION HAZARD DECAL, ART S-WAY LOGO DECAL, DANGER 565 RPM PTO DECAL, ROLLERMILL OPERATION DECAL, MOVING PART HAZARD REFLECTOR, RED REFLECTOR, AMBER DECAL, ART S-WAY LOGO 11.5 X A DECAL, 5105 GRINDER MIXER 2 N/A -25B DECAL, 5165 GRINDER MIXER N/A DECAL, CATTLEMAXX DECAL, TANK WINDOW DASH DECAL, ATTENTION FOREIGN MATERIAL = Not Illustrated ART S-WAY MANUFACTURING COMPANY Manual No (Jul 2007)

80 THIS PAGE LEFT INTENTIONALLY BLANK

81 ART S-WAY MANUFACTURING CO., INC. TECHNICAL MANUALS Manuals are available from your local dealer or Art s-way Manufacturing Co., Inc. for the operation, service, and repair of your machine. For prompt convenient service, contact your local dealer for assistance in obtaining the manuals for your machine. Your local dealer can expedite your order for operator manuals, illustrated parts catalogs, service manuals, and maintenance records. Always give the Machine Name, Model, and Serial Number so your local dealer can provide the correct manuals for your machine. Art s-way Manufacturing Co., Inc. reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. Except as expressly authorized, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Art s-way Manufacturing Co., Inc. ART S-WAY MANUFACTURING CO., INC. HWY 9 WEST - PO Box 288 Armstrong, IA U.S.A Copyright 2005 ART S-WAY MANUFACTURING CO., INC. All Rights Reserved

82 Produced In The U.S.A. By CPS DYNAMICS, LLC PO Box 9007 Wichita, KS Art s-way Manufacturing Co., Inc. Hwy 9 West PO Box 288 Armstrong, IA U.S.A