FRP/GRP Solutions for Cable Management Systems

Transcription

1 FP/GP Solutions for Cable Management Systems

2 elcome to Enduro. This product catalog and guide provides the information you need to design your cable management solution. Should you need additional information feel free to contact us at or at Please also visit our website at Thank you for your interest in Enduro cable tray systems. e look forward to working with you.

3 Over 5 Years Experience Enduro is the world leader in the manufacture and development of Quality & Consistency ith a world-class quality testing laboratory, Enduro ensures consistent and reliable product performance through comprehensive programs of quality control. Single Source esponsibility lutions for over three decades, our product offering is one of the broadest in the industry. Combined with our other manufacturing, engineering and design capabilities, this enables us to offer application- vertically integrated, we can deliver these solutions on time and on budget, at the quality level our customers expect. Engineering & Enduro s experienced technical staff can provide engineering and de- chances are good we have encountered something similar before. the success of a composite cable management solution. ith our broad history of installations in a wide variety of challenging environments, we can help you specify the best resin system and the right structural properties to ensure long life and low cost of ownership. e can assist you in the design process with utocd details. In addition, Enduro s cable tray offering is available in PDMS. Contact us today for more information. Customer Service & Sales Support Our Customer Service desk is available to assist with questions, product selection or quotes. Please call us today at or sales@endurocomposites.com. Our road Experience Offshore Platforms Subsea pplications Chemical Plants Petrochemical Complex Desalination Plants Salt Processing Tunnels, ridges, Causeways

4 adder Cable Tray Page 8-2 adder Cable Tray Fittings Page -2 Channel-Type Instrumentation page 28- page 25 adder Cable Tray Splice Plates Page adder Cable Tray Page page 4 45 thru 5 page 8 Cover Hold Down Clamp page 26 Drop Out page 27 Channel-Type Page 28- Flanged-Type Page 2- Instrument Support Stands page 44 ireway Page 4-7 Support Systems & Strut Page 8-4 Fastener & Hanger Systems Page 42-4 utton Stands Page 44 end page 4 4 CE TY SYSTEMS

5 Push utton Support Stand page 44 page 6 ift Off Cover page 25 ay-in ireway with Cover page 4 Expansion Splice Plate page 2 page 6 Splice Plate page 2 Straight Sections pages 8-9 Support Systems Hanging Systems page 8-42 page 5 Divider Strip page 27 0 Joining ends page 5 lind End page 27 page 2 This illustration is for parts visualization only and does not represent an actual layout. Not all parts are pictured here. CE TY SYSTEMS 5

6 FP/GP Technical Data Technical Data Typical Properties of Structural FP/GP ongitudinal Direction Transverse Direction Mechanical (coupon) F-P F-VE Mechanical (coupon) F-P F-VE Ultimate Tensile Strength, PSI (STM D68) 0,000 5,000 Ultimate Tensile Strength, PSI 7,000 0,000 Ultimate Compressive Strength, PSI (STM D695) 0,000 5,000 Ultimate Compressive Strength, PSI 5,000 20,000 Ultimate Flexural Strength, PSI (STM D790) 0,000 5,000 Ultimate Flexural Strength, PSI 0,000 4,000 Tensile Modulus, PSI x Tensile Modulus, PSI x Compressive Modulus, PSI x Compressive Modulus, PSI x Flexural Modulus, PSI x Flexural Modulus, PSI x Ultimate Shear Strength, PSI 5,500 7,000 Ultimate Shear Strength, PSI 5,500 6,000 Ultimate earing Stress, PSI 0,000 5,000 Ultimate earing Stress, PSI 0,000 5,000 Izod Impact Strength, Ft.-bs. per inch of notch Izod Impact Strength, Ft.-bs. per (STM D256) (sample thickness inch of notch (STM D256) 4 5 except 4 for rod) arcol Hardness (STM D Electrical Mechanical (coupon) F-P F-VE Electric Strength, short term in oil, 8, vpm (STM D49)* Electric Strength, short term in oil, KV per inch 5 5 Dielectric Constant, 60 Hz.(STM D50)* Dissipation Factor, 60 Hz. (STM D50)* rc esistance, seconds (STM D495)** Fire etardant Properties Mechanical (coupon) F-P F-VE Flame esistance, ign/burn, seconds (FTMS ) 75/75 75/75 Intermittent Flame Test, rating (HT-5) Flammability Test average time of burning 5 seconds, average extent of burning 5mm (STM D65) Surface urning Characteristics, maximum (STM E84) Full Section in ending Mechanical (coupon) F-P F-VE Modulus of Elasticity, PSI x Tensile Strength, PSI 20,000 25,000 Compressive Strength, PSI 20,000 25,000 Thermal Mechanical (coupon) F-P F-VE Thermal Coefficient of Expansion Inches/Inch/ F (STM D696)** 5 x x 0-6 Thermal Conductivity, TU per Sq. Ft./Ht./ F/In. (STM C-77-76) 4 4 Specific Heat, TU/b./ F Density, bs./in. (STM D792) Specific Gravity (STM D792) ater bsorption, Max. % by weight (24 hour immersion) (STM D570) Concentric Static oad (if required) concentrated static load is not included in the table on page 9. Some user applications may require that a given concentrated static load be imposed over and above the working load. Such concentrated static load represents a static weight applied be- e If the combined load exceeds the working load shown, please contact us. This data e = to assist in the proper selection of the most appropriate cable tray type offered by Enduro. Other Mechanical (coupon) F-P F-VE Note: PSI = K Pa; Ft.-b./In. = 5.44 kg-m/m; * Specimen tested perpendicular to laminate face ** Indicates reported value measured in longitudinal direction; Depending on the specific glass content and resin, the strength and stiffness properties may be significantly higher. Contact us for specific values on Halogen-Free ow Smoke Plus resin properties. Thermal Contraction & Expansion The table to the right compares the thermal contraction and expansion based on various temperature differen- values shown represent the length of cable tray that will produce a 5 8 movement between expansion connectors the least movement. Enduro has expansion connectors to provide for total movement of 5 8. Fiberglass vs Steel vs luminum Temp. Fiberglass Steel luminum Differential Ft. (m) Ft. (m) Ft. (m) 25 F (4 C) 47 (26) 20 (97) 62 (49) 50 F (28 C) 208 (6) 60 (48) 8 (25) 75 F (42 C) 8 (42) 06 (2) 54 (6) 00 F (56 C) 04 (2) 80 (24) 40 (2) 25 F (69 C) 8 (25) 6 (9) 2 (0) 50 F (8 C) 69 (2) 5 (6) 26 (8) 75 F (97 C) 59 (7) 45 () 2 (6) 6 CE TY SYSTEMS

7 FP/GP Technical Data Effect of Temperature - FP/GP Strength properties of reinforced plastics are reduced when continuously exposed to elevated temperatures. orking loads shall be reduced when based on the table to the right. Percentages shown are approximate. If unusual ing temperatures do not adversely affect the load rating capability of the tray. review should be made of applications involving service temperatures over Temp. Polyester Strength % Vinyl Ester Strength % 75 F (24 C) 00% 00% 00 F (8 C) 90% 00% 25 F (52 C) 78% 00% 50 F (66 C) 68% 90% 75 F (79 C) 60% 90% 200 F (9 C) 52% 75% The test values in the chart below were obtained from tests conducted by Enduro s vinyl ester resin supplier. The values shown, although obtained from an actual coupon test, are intended for illustrative purposes only, and not for use in design calculations. The values for polyester are slightly lower. Technical Data Test Temp. F ( C) (-7 ) (-46 ) (-8 ) (0 ) (25 ) (8 ) (66 ) (9 ) (2 ) (49 ) Flex. St., PSI, STM D790 0,500 86,400 79,500 72,00 68,00 66,00 58,700 27,400,200 9,200 Flex. Mod., PSI x 0 6, STM D Tensile St., PSI, STM D68 84,00 70,400 6,900 58,000 56,00 54,600 49,900 4,800 29,600 22,000 Corrosion esistance of esin Systems Enduro offers a variety of resin systems which are listed in more detail on page 9. The two resin systems most often used are of the proper standard resin system for individual application. Polyester and vinyl ester resin systems are available in conductive formulation. Contact us for corrosion resistance information for halogen-free and halogen-free low smoke plus resins. Chemicals 75 F (24 C) 60F (7 C) Chemicals 75 F (24 C) 60 F (7 C) cetic cid 5% F-P F-P Magnesium Chloride F-P F-P cetic cid 25% F-P F-VE-20 (*) Methyl lcohol 0% F-P F-VE-50 (*) luminum Potassium Sulfate 5% F-P F-P Naphtha F-P F-P mmonium Hydroxide 0% F-P F-VE-50 Nitric cid 5% F-P F-P mmonium Nitrate F-P F-P Nitric cid 20% F-VE F-VE-20 (*) enzenesulfonic cid 5% F-P F-P Phosphoric cid 0% F-P F-P Calcium Chloride F-P F-P Phosphoric cid 0% F-P F-P Carbon Tetrachloride F-VE F-VE-00 (*) Phosphoric cid 85% F-P F-P Chlorine Dioxide 5% F-P F-VE-50 (*) Sodium icarbonate 0% F-P F-P Chromic cid 5% F-P F-VE-50 (*call) Sodium isulfate F-P F-P Copper Sulfate F-P F-P Sodium Carbonate F-P F-VE Diesel Fuel No. F-P F-P Sodium Chloride F-P F-P Diesel Fuel No. 2 F-P F-P Sodium Hydroxide -50% F-VE F-VE-20 (*) Ethylene Glycol F-P F-P Sodium Hypochlorite 5% F-P F-VE-20 (*) Fatty cids 00% F-P F-P Sodium Nitrate F-P F-P Ferrous Sulfate F-P F-P Sodium Silicate F-P F-VE-20 (*) Fluosilicic cid 0-20% F-VE F-VE (call) Sodium Sulfate F-P F-P Hydrochloric cid % F-P F-P Sulfuric cid 0-0% F-P F-P Hydrochloric cid 5% F-P F-VE-80 (*) Sulfuric cid 0-50% F-VE F-VE Hydrochloric cid 7% F-P F-VE-50 (*) Sulfuric cid 50-70% F-VE F-VE-80 (*) Hydrogen Sulfide F-P-40 F-VE-20 Trisodium Phosphate 25% F-P F-VE-20 (*) Kerosene F-P F-P Trisodium Phosphate - ll F-VE F-VE-20 (*) ater, Distilled F-P F-P F = Fire-etardant; P = Polyester esin; VE = Vinyl Ester esin; (*) = Not recommended to exceed this temperature; call = Call for recommendations Information contained in this chart is based on data from raw material suppliers and collected from several years of actual industrial applications. Temperatures are but individual test data should be required to establish such suitability. The recommendations or suggestions contained in this chart are made without guarantee or CE TY SYSTEMS 7

8 adder Cable Tray Selection Guide Selection Guide Imperial Straight Section Part Numbers TYPE - () - (S) - () Example: EH Side ail ung System No. Height idth Spacing ength ung See adder Cable Tray 6=6 2=2 2=2 8=8 8=8 8=8.5 tions, add requested type 0=0 24=24 0=0 6=6 Metric Straight Section Part Numbers TYPE - () - (S) - () Example: EH M Side ail ung System No. Height idth Spacing ength ung See adder Cable Tray 6=6 00=00mm 00=00mm tions, add requested type 8=8 450=450mm 470=470mm 0=0 600=600mm 750=750mm 900=900mm System Diagrams SIDE I HEIGHT ODING DEPTH 4 (6mm) FNGE IDTH FNGE IDTH SIDE I HEIGHT ODING DEPTH 4 (6mm) E EH6 ET4 D-EH6 EH4 EH8 ET6 D-EH0 E6 (25mm) EHZ6 (25mm) idth represents inside dimensions. Solid bottom available upon request. - cation page 2, item 5..2 for details. Please contact us for any other custom - widths. adder Cable Tray Selection Guide Standard Optional Side ail oading System No. System No. Height Depth (polyester resin) see bottom of pg. In. (mm)* In. (mm) E ET4 EH4 ET6 E6 EH6 D-EH6 EHZ6 EH8 Flange idth In. (mm) Min. Channel Thickness In. (mm) 6 6 (75) (46) (25) (4.8) (00) (7) (28) (4.0) (00) (70) (28) (6.4) (52) (22) (4) (4.0) (52) (22) (4) (4.8) (52) (2) (4) (6.4) (52) (9) (4) (8.0) (52) (9) (5) (6.4) (20) (70) (44) (8.0) NEM Class FG C 20C 20C 20C Safety Factor isting - - Class - Class Class C Class C - Class C D-EH0 0 (254) (29) 2 4 (70) 8 (9.5) 0C Please note: Custom resin systems may require additional lead times. 8 CE TY SYSTEMS

9 adder Cable Tray Selection Guide Polyester Vinyl Ester esin Systems elow is an overview of the common resin systems we offer. hen choosing a resin type for your application, we highly rec- epoxy vinyl ester system is preferred for optimum durability. Conductive corrosion resistance. This system is especially suitable for seawater environments. This resin system also delivers good weathering performance, but is superior to a polyester with respect to corrosion resistance and high heat environments. Epoxy vinyl ester resins provide greater toughness and considerably higher strength at elevated temperatures. They also provide superior resistance to chemical attack in corrosive chemical service. This Isophthalic Polyester-based resin is formulated to comply with S requirements for conductivity. To pro- Selection Guide Halogen-Free Polyester Halogen-Free Vinyl Ester This system offers similar performance attributes as our standard Isophthalic Polyester, but without the use of halogens. Halogen-Free ow Smoke Plus Tray eight bs/ft. (kg/m) 2 width, 2 rung spacing 8 (2.4m) 0 (m) orking (llowable) oad bs./ft. (kg/m) 4 6 (4.m) (4.9m) 2 (.7m) 8 (5.5m) 20 (6.m) (.0) (74).0 50 (4.5) (74) (4.5) (67) (07) (74) (4.) (77) (24) (67) (2) (94) (74) (6.7) (298) (207) (52) (6) (92) (74) (6.7) (04) (2) (84) (49) (7.) (04) (2) (84) (49) (7.) (04) (2) (84) (49) (9.5) (04) (2) (84) (49) 0 (9.m) (4.) (4) (5) (49) U listed. CE TY SYSTEMS 9

10 The installation of Enduro Cable Tray should be made purchaser. lways observe common safety practices when assem- - cause skin irritation and, if allowed to accumulate with grease and other machining lubricants, can become abrasive. Personnel should wear safety goggles, dust mask, coveralls or a shop coat when sawing, machin- conductive and additional considerations apply. void generating excessive heat in any machining op- glass, resulting in a ragged rather than a clean-cut edge. void excessive pressure when sawing, drilling, routing, etc. Use carbide-tipped drill bits and saw blades for extended tool life. The use of lubricant during machining is not recommended. To avoid chipping of material at cut edges, secure cable made. hen using adhesives, be sure to prepare the sur- carefully. combination of mechanical fasteners and adhesives make the strongest most reliable connections. Support ocation Guidelines* Correct ength of Span = in Multiple Span Condition Support Support intended or designed to be a walkway for personnel. The user is urged to display appropriate warning cautioning against the use of this support as a walkway. 0 CE TY SYSTEMS

11 Straight Sections Supports must be located so that connector between the support point and the quarter point of the span. Splice at /4 ength of Span = in multiple span condition Splice at /4 Standard engineering practice requires that the splice bending moment. This allows the cable tray system to act as a continuous member with spans working in located directly over the support, the previous continuous span condition is changed to one of a number of simple spans. SUPPOT at the 45 degree point of the arc, 45 degree supports These spans act independently of each other and excessive stress will occur at substantially less loading. vals dictated by the building structure not exceeding expansion connection. Vertical Fitting Supports SUPPOT ø 2-0 Max (.6 m) 2-0 Max (.6 m) ø ø 2-0 Max (.6 m) /2ø ø of the three openings connected to other cable tray least one support should also be placed under each side rail of the tee. /2 2-0 Max TYP educer Fitting Supports extremity. 2-0 Max TYP (.6 m) 2-0 Max TYP (.6 m) TYP 2/ 2-0 Max 2-0 Max TYP TYP (.6 m) (.6 m) 2-0 Max TYP Vertical Tee Supports four openings connected to other cable tray items for one support should also be placed under each side rail of the cross. 2-0 Max TYP (.6 m) 2-0 Max 2-0 Max TYP (.6 m) TYP (.6 m) 2-0 Max TYP (.6 m) 2/ TYP 2-0 Max TYP (.6 m) CE TY SYSTEMS

12 .0 Scope. The cable tray system shall conform to the material and 2.0 Standards 2. The cable tray system shall conform to applicable sections of: Systems.0 General support span: Class orking oad FOS 50 bs./ineal Ft bs./ineal Ft..5 C 00 bs./ineal Ft..5 Support orking oad in bs./ineal Ft. Span (Ft.) Class Class Class C Materials between 45 to 55 percent by weight in all pultruded components. 4.2 ll composite material shall have an ultraviolet light when tested in accordance with STM E ll pultruded products shall have a complete surfacing 5.0 Construction meeting all the requirements herein described. 5.. The side rail members must turn in ll rung to side member connections shall have lock. The tray shall be assembled by the use thermoplastic. The locking pin shall be inserted under pressure with a high strength, chemical resistant adhesive. 5.. ll bonded connections must be sanded to 5..5 ll straight section lengths shall be pre-drilled to accept connector plates. shall be resin coated. requirements herein described. spacing. connector plates. as to have the same load carrying capacity as the straight sections. The locking pin shall be inserted under pressure with a high strength chemical resistant adhesive. members shall be of concentric curved molded design and made by resin transfer molding. be installed between 0.2 and 0. of the length of the span from the support without derating the load carrying capacity of the tray Connector plates for conductive tray shall be stainless steel. nuts as required. 5.4 ccessories 5.4. The manufacturer shall be capable of providing manufactured - pultrusion, compression molded, resin Inc., of Houston, Texas US. Cable Tray 2 CE TY SYSTEMS

13 adder Cable Tray - Molded Fittings For conductive and halogen-free formulations, please contact us for availability and lead time. It is recommended to use expansion splice plates and 4 or chemical lock. Please see page 2, item for details. Standards & istings Imperial Molded Fittings Part Numbers TYPE - - -()-() Example: EH - MC Side ail 0 = 0 6 = 6 Covers = EC before after after Metric Molded Fittings Part Numbers TYPE - - -()- () Example: EH - MC Molded Fittings Side ail 750 = 750mm 900 = 900mm before after after Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth *** (52) (578) (88) (882) (248) (87) (680) (229) (654) (926) (959) (56) (264) (787) ** (05) (405) (0) (05) (464) (40) (895) ** (457) (88) (248) (87) (680) (492) (2) ** (60) (05) (464) (40) (895) (645) (224) N N (762) (87) (680) (492) (2) N N (94) (40) (895) (645) (224) of the inside distance from tray wall to tray wall; **lso available in 4 and 8 side rail; *** lso available in 4 side rail; lso available in 8 side rail CE TY SYSTEMS

14 Molded Fittings - adder Cable Tray 90 Vertical end adius Channel Depth Inches (mm) 4 Tray 6 Tray 8 Tray 2 N N N N (05) (578) (88) (60) (8) (78) (88) (56) (92) (8) 6 N N N N (94) (87) (680) Molded Fittings Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth *** (52) (227) (44) (4) (657) (42) (87) (229) (29) (495) (48) (7) (508) (927) ** (05) (405) (549) (494) (765) (584) (98) ** (457) (557) (657) (646) (87) (77) (089) ** (60) (70) (765) (798) (98) (889) (97) N N (762) (862) (87) (95) (089) N N (94) (04) (98) (0) (97) 45 Vertical end adius Channel Depth Inches (mm) 4 Tray 6 Tray 8 Tray 2 N N 2 6 N N (05) (0) (55) 24 N N (60) (49) (75) (470) (786) 6 N N N N N N (94) 5 of the inside distance from tray wall to tray wall; ** lso available in 4 and 8 side rail; *** lso available in 4 side rail; lso available in 8 side rail 4 CE TY SYSTEMS

15 adder Cable Tray - Molded Fittings Joining 45 Vertical ends X X = Y = Y Contact us for assembly method. Y X = Y = X 0 Vertical end =24 5 = () 6 () 24 6 () Molded Fittings () 5 =24 =24 vailable in 6 and 24 radius depth channel. Joining 0 Vertical ends X X = 2 - Y = Y Dimensions Inches (mm) adius (05) (457) (889) (60) (5) (092) (94) (65) (2) Dimensions apply at 45 setting. H = Side ail Height; = adius; = idth of the inside distance from tray wall to tray wall CE TY SYSTEMS 5

16 Molded Fittings - adder Cable Tray Molded Fittings 2 Contact us for dimensions on reducing tee. Contact us for dimensions on reducing cross. unable to be shipped via regular motor freight lines. Dimension Inches (mm) 2 (05) adius 24 (60) adius** 6 (94) adius idth (52) (578) (99) (88) (600) (87) (220) (229) (654) (067) (959) (676) (264) (2286) (05) (70) (4) (05) (75) (40) (262) (457) (88) (295) (87) (905) (492) (255) (60) (05) (448) (40) (2057) (645) (2667) (762) (87) (600) (492) (220) (797) (289) (94) (40) (75) (645) (262) (949) (2972) Dimension Inches (mm) 2 adius 24 adius 6 adius idth ** (52) (99) (600) (220) (229) (067) (676) (2286) (05) (4) (75) (262) (457) (295) (905) (255) (60) (448) (2057) (2667) (762) (600) (220) (289) (94) (75) (262) (2972) 2 90 Vertical Tee Dimensions Inches (mm) Tap up and tap down have the same dimen- adius (05) (578) (00) ** 6 2 (60) (8) (6) (94) (87) (222) Tap Down = adius; = idth of the inside distance from tray wall to tray wall; ** lso available in 4, 6 and 8 side rail 6 CE TY SYSTEMS

17 adder Cable Tray - Mitered Fittings - istings & pprovals Imperial Mitered Fittings Part Numbers TYPE - - -()-() Example: EH - H Side ail EH8 E ET4 D-EH6 E6 ET6 D-EH0 EHZ6 See Selection Table Polyester T H MZ S TS HS HSZ Y TY HY HYZ ow Smoke Plus Conductive before order item, see page 4. after after Metric Mitered Fittings Part Numbers TYPE - - -()- () Example: EH - H Tray Type/esin Selection Table EH4 EH6 ook at left column to select resin, then look at top row to select tray type. Then, insert Mitered Fittings Side ail See Selection Table before ers for covers are separate order item, see page 4. after after endering Example Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth (52) (854) (207) (59) (68) (464) (2070) (229) (90) (4) (25) (746) (540) (278) (05) (006) (422) () (854) (66) (2286) (457) (59) (68) (464) (2070) (768) (2502) (60) () (854) (66) (2286) (92) (278) (762) (464) (2070) (768) (2502) (207) (29) (94) (66) (2286) (92) (278) (2226) (46) H = Side ail Height; = adius; CE TY SYSTEMS 7

18 Mitered Fittings - adder Cable Tray 2 adius 24 adius 6 adius Dim. Inches Depth** Depth** Depth** (mm) (50) (50) (50) (85) (85) (85) (749) (749) (749) (8) (8) (8) () () () (608) (608) (608) 90 Vertical Outside end Mitered Fittings Dim. Inches (mm) 2 adius 24 adius 6 adius Depth** Depth** Depth** (505) (555) (606) (80) (860) (9) (74) (786) (857) (45) (28) (289) (4) (65) (26) (576) (648) (72) Dimensions Inches (mm) 6 (52) (0) 9 (229) 6 (406) 2 (05) 9 (48) 8 (457) 25 (65) 24 (60) (787) 0 (762) 7 (940) 6 (94) 4 (092) (Varies) 6 (406) = adius; = idth of the inside distance from tray wall to tray wall; ** Contact us for availability of (76mm) 8 CE TY SYSTEMS

19 adder Cable Tray - Mitered Fittings Dimension Inches (mm) 0 ngle (ø) 45 ngle (ø) 60 ngle (ø) - idth (52) (57) (800) (42) (762) (487) (700) ø (229) (4) (88) (508) (84) (564) (767) (05) (50) (876) (584) (870) (640) (82) (457) (675) (999) (756) (02) (8) (002) (60) (827) (075) (9) (29) (965) () (762) (979) (5) (060) (27) (8) (267) (94) (2) (227) (2) (45) (270) (99) Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth (52) (525) (987) (66) (20) (705) (49) (229) (602) (04) (692) (257) (78) (47) (05) (678) (095) (768) () (857) (527) (457) (80) (20) (92) (49) (00) (65) (60) (98) () (07) (527) (62) (74) (762) (5) (49) (226) (65) (4) (846) (94) (287) (527) (78) (74) (467) (957) Mitered Fittings ll dimensions are to the nearest 4 Dim. Inches (mm) 0 2 adius 24 adius 6 adius Depth Depth Depth (20) (229) (254) (05) (229) (254) (05) (56) (279) (05) (56) (8) (457) (457) (457) (457) (60) (60) (60) (60) (762) (762) (762) (762) 45 ** ** (28) (8) (52) ** (70) (406) (44) ** (470) (495) (52) (505) (505) (505) ** (72) (72) (72) ** (97) (97) (97) = adius; = idth of the inside distance from tray wall to tray wall; ** Contact us for availability of (76mm) CE TY SYSTEMS 9

20 Mitered Fittings - adder Cable Tray 0 /45 Vertical Outside end ll dimensions are to the nearest 4 Dim. Inches (mm) 0 2 adius 24 adius 6 adius Depth Depth Depth (78) (20) (254) (254) (229) (254) (05) (05) (279) (05) (56) (56) (42) (42) (457) (457) (584) (584) (60) (60) (77) (77) (762) (762) 45 ** ** (27) (24) (75) ** (64) (44) (465) ** (452) (50) (554) (487) (522) (559) ** (70) (78) (775) ** (98) (954) (99) Dim. Inches (mm) 0 ngle (ø) 45 ngle (ø) Depth** Depth** Mitered Fittings 5 (8mm) ø.5 (4mm) (259) (0) (48) (4) (5) (86) (678) (678) (678) (624) (624) (624) 0 /45 Vertical Outside Direct end 6.75 (425mm) 5 (8mm) ø Dim. Inches (mm) 0 ngle (ø) 45 ngle (ø) Depth** Depth** (00) (44) (408) (57) (408) (47) (749) (749) (784) (68) (68) (70) Straight educer Inches (mm) 6 (94) 0 (762) 24 (60) 8 (457) 2 (05) 9 (229) 2 2 Inches (mm) (52) (05) (029) (95) (876) (679) (670) (229) (067) (99) (94) (88) (670) (05) (029) (95) (94) (679) (457) (95) (908) (679) (60) (908) (679) (762) (679) Dimension Inches (mm) = adius; = idth of the inside distance from tray wall to tray wall; ** Contact us for availability of (76mm) 20 CE TY SYSTEMS

21 ight or eft Hand educer adder Cable Tray - Mitered Fittings Inches (mm) 6 (94) 0 (762) 24 (60) 8 (457) 2 (05) 9 (229) 6 (52) 55 2 (40) 46 4 (75) 46 4 (75) 7 (940) 7 (940) 27 4 (705) (229) (75) (75) (940) (940) (705) (05) (75) (940) (940) (705) (457) (940) (940) (705) (60) (940) (705) (762) (705) Dimension Inches (mm) 2 Inches (mm) 2 Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth (52) (780) (40) (080) (880) (90) (2580) (229) (850) (40) (60) (20) (460) (2580) (05) (90) (40) (240) (20) (540) (2820) (457) (080) (640) (90) (250) (690) (2820) (60) (240) (880) (540) (250) (840) (050) (762) (90) (880) (690) (2580) (2000) (290) (94) (540) (20) (840) (2820) (250) (290) Mitered Fittings Dimension Inches (mm) 2 (05) adius 24 (60) adius 6 (94) adius idth (52) (90) (40) (2000) (880) (260) (2580) (229) (470) (40) (2080) (20) (2690) (2580) (05) (540) (40) (250) (20) (2760) (2820) (457) (700) (640) (20) (250) (290) (2820) (60) (850) (880) (2460) (250) (070) (050) (762) (2000) (880) (260) (2580) (220) (290) (94) (250) (20) (2760) (2820) (70) (290) Vertical Tee Dimensions Inches (mm) different than tap down, contact us for dimensions. adius (60) (860) (568) (94) (65) (278) Tap Down H = Side ail Height; = adius; = idth of the inside distance from tray wall to tray wall CE TY SYSTEMS 2

22 Splice Plates - adder Cable Tray 7 6 pre-drilled bolt holes. NEM FG- Please refer to NEM FG- regarding proper tray installation as it pertains to support and splice plate locations for straight adder Cable Tray Splice Plate Part Numbers TYPE - -(D) Example: ESP - 6C - 80 Splice Plates Side ail Type Height Material Degree * C = Polyester 80 = Straight, Expansion * * SS = Stainless Steel 45 = 45 * * 22.5 = 22.5 ** requires 4 bolt sets per plate. Side rail height of 6 and 8 requires 8 bolt sets per plate. Side rail height of ** Splice Plate and Hardware Options Tray esin Splice Plate Material Hardware Material Sets Polyester Vinyl Ester Halogen-Free Polyester 6 Stainless Steel 6 Stainless Steel Monel Silicon ronze Isoplast Polyester Standard Optional Optional Standard Optional Optional Optional Vinyl Ester Standard Optional Standard Optional Optional Optional Halogen-Free Polyester Optional Optional Standard Standard Optional Optional Optional Halogen-Free Vinyl Ester Standard Standard Optional Optional Optional Halogen-Free ow Smoke Plus Standard Standard Optional Optional Optional Conductive Standard Standard Optional Optional Optional Hardware Type Set Includes Size For Use ith Tray Types 6 Stainless Steel olt Set olt, nut 8-6 x For S.S. splice plates (except 0 Channel) 50566SS 6 Stainless Steel olt Set olt, nut 8-6 x 4 ll tray types (except 0 Channel) 50567SS* 6 Stainless Steel olt Set olt, nut, 2 washers 8-6 x 2 For use with V splice place 50568SS Monel olt Set olt, nut 8-6 x 4 ll tray types (except 0 Channel) 60667M FP/GP Studs & Nuts Stud and 2 nuts 8-6 x 2 E, E4, ET6, EHZ6 FP/GP Studs & Nuts Stud and 2 nuts 8-6 x 2 2 EH6, EH8, EHV6 Silicon ronze olt Set olt, nut 8-6 x 4 ll tray types (except 0 Channel) 80867S * Standard hardware set; NOTE: For monel and silicon bronze, please contact us for lead times. lso available in additional sizes. For 0 channel, please contact us for hardware; It is recommended that expansion splice plates and 2 long assembly fasteners be used when connecting mitered fittings to molded fittings or straight lengths. Fastener Torque Inch: GD. 2 UNC Metric: Class 5.8 Size Ft-bs Size N-m / M8 x / M0 x / M2 x olt Type: Contact us for different types and sizes. Nut 22 CE TY SYSTEMS

23 adder Cable Tray - Splice Plates Typical Dimensions for FP/GP Splice Plates Typical Dimensions Inches (mm) Channel Depth Inches (mm) C (76) 4 (44) (25) -0-4 (02) 2 (5) (25) -0-6 (52) (7) (25) (67) 8 (20) 6 (52) 6 (4) (67) Typical Dimensions for Stainless Splice Plates Typical Dimensions Inches (mm) Channel Depth Inches C (mm) (76) 4 (2) 5 8 (6) -0-4 (02) 4 (2) 5 8 (6) -0-6 (52) 4 8 (05) 4 (9) (67) 8 (20) 4 8 (05) 4 (9) (67) Straight Section Expansion 90 Vertical (225) 4 (2) 4 4 (08) 6 8 (62) 7 6 x ( x 25) slot (276) (7) Field Drilling equired C 7 6 () hole 45 Vertical 0 Vertical 22.5 Vertical Splice Plates 7 6 () hole (24) 45 4 (2) C 7 6 x ( x 25) slot, typ (7) 5 6 (29) (25) (25) (67) (8) C 4 (2) (62) For adjustable vertical plate hardware, use catalog number 50568SS. For travel dimensions, contact us (8) CE TY SYSTEMS 2

24 Splice Plates - adder Cable Tray 6 (52) 4 (2) (24) C 7 6 () hole Heavy Duty Splice Plates 4 (2) 4 (2) 2 4 (70) stock +_ 6 Splice Plates +_ () ø 7 4 (48) Side ail Height Inches (mm) (67) Inches (mm) Inches (mm) 7 4 (48) 4 (02) (76) 8 (5) 6 (52) 5 (27) 8 (5) 8 (204) 6 8 (62) 2 6 (52) 0 Channel Splice Plates ESP-0C-80 Splice Plate EEP-0C-80 Splice Plate (0) 4 Plcs. (0) 4 Plcs. 4 (44) 2 6 (68) (67) 5 6 (7.9) 8 (204) C8 x 4 x (50.8) 4 (2) 2 (50.8) 7 6 () Dia. 2 Plcs. 7 6 () x Slot 2 Plcs. 4 (2) * In Key, parentheses ( ) = insert corresponding option code; H = Side ail Height - 4, 6, 8 (inches) 24 CE TY SYSTEMS

25 Enduro offers a full line of accessories for our electrical products including cable tray covers, divider strips, drop outs, blind ends, adapters, hold-down clips, marine rungs, strut rungs, swivel clamps and a wide variety esin Designation cover, solid bottom is also available. See page 26 for cover accessories. Clampless Flat Cover Stainless embedded nut pre-installed by Enduro Eliminates the need for Cover Hold Down Clamp for a quicker and total of three pairs of stainless embedded nuts are pre-installed to the cable tray channels by Enduro. Contact us for metal types available on embedded nuts. 4 are also included and shipped separately. Flat Cover - It is recommended rivets be installed on 24 centers along both side rails. Cover Hold Down Clamps and Enduro Stand Offs allow cover to be removed for easy access to cables - see page 26. It is recommended to use seven pair at 6 on Diagram shown is ventilated. Tray C Tray Z Tray idth Type t./f Type t./f Inches (mm) 6 (52) EPC EZC (229) EPC EZC (05) EPC-2.4 EZC (457) EPC-8.7 EZC (60) EPC EZC (762) EPC EZC (94) EPC-6.42 N N Example: EC-EH-MC Peaked Cover Tray idth - H Contact us for Z-Tray covers. Installation Methods for Peaked Cover: Use three pair of Enduro Stand Offs - Peaked for each 0 ft. length of tray. Contact us for information on 22.5, 0 and 45 peaked covers. dd ventilation height 4 for peaked cover. Peaked covers can be ventilated or non-ventilated. Diagram shown is ventilated. C Tray Dimensions In. (mm) Type H t./f EPC (52) 0.6 (5) 0.77 EPC (229) 0.9 (2) 0.77 EPC (05).2 (). EPC (457).8 (46).5 EPC (60) 2.4 (6).9 EPC (762).0 (76) 2. EPC (94).6 (9) 2.4 = idth of the inside distance from tray wall to tray wall CE TY SYSTEMS 25

26 Stand Off ESO Stand Off Peaked ESOP Cover Hold Down Clamp resin is the standard. Includes mounting hardware. 2 2 STD 8 x 4 6 SS bolt, flat washer, & lock washer two required resin is the standard. Includes mounting hardware. 2 4 STD 8 x 4 6 SS bolt, flat washer, & lock washer two required.25 for EHZ6 tray. cover hold down clamp cover SS bolt 8 x 2 with nut & flat washer Complete Cover Hold Down 2 centerline of.475ø holes 4 places 4 SS nut 4 required 4 Conduit Swivel Clamp tray in an outdoor application. est suited for a high wind applications. vailable in stainless steel, contact us for dimensions. Hold Down Clamp & Expansion Guide Enduro s XHDC serves as both a Hold Down Clip and Expansion nates the need for ordering or tracking multiple products for securing ladder tray to structural supports. Installation: To determine the appropriate orientation for installation, rotate the XHDC to the corresponding letter indicator shows which letter indicator to use for each series, for use as XHDC Hold Down Clamp T T H H H D Expansion Guide H H H H D D D Contact Us tray depth +4 Tray Type E ET4 EH4 ET6 E6 EH6 D-EH6 EHZ6 EH8 D-EH0 4 SS threaded rod square rung 2 required tray width + Floor / Panel Flange Plate Side ail Height Dim. Dim. (76) (02) (52) (20) (254) code. ll drilled holes are 7 6 in diameter. Hole pattern varies with tray type. tray depth This allows an easy transi- substitute cable tray designation when ordering clamps are separate order - of part number - example: 7 6 (.) 5 6 (7.9) 4 (6.4) 4 (0.6) 6 (4.8) 8 (9.5) eam Hold Down Guide Eliminates the Need to Drill or Punch Holes Normal Expansion stainless steel guide that secures the position of cable tray on a support rack or structure. NE of a 6 SS set screw on top. Set screw is included with part. right or left sided installations. H = Side ail Height, available heights (inches):, 4, 6, or 8; = idth of the inside distance from tray wall to tray wall; TD = Tray Designation 26 CE TY SYSTEMS

27 Divider Strip Divider strips are supplied in ten foot lengths. Unless indicated otherwise, dividers are indicate installation position if required. nished with factory-drilled notching with additional cost. please contact us for part numbers. use 6 SS rivets. e also have available able clamp, does not include divider strip. Nylon Thermoplastic Drive ivet vider strip. Pigmented to match resin type. Drop Out ctual width of Drop Out is less than width of tray to allow for placement - number. Drop Out installation for less than 2 width: Drill two 4 holes from opening. lind End 6 SS fasteners included H Example for a 6 wide rung, polyester Hardware included. Example for a 6 wide rung, polyes- Hardware included. Drop Out installation for more than 2 width: Drill three 4 holes from each end and in the middle. 2 4 (70) Side View 4 (9) (25) 6 (5) 4 (2) Example for a 6 wide rung, polyes- Cable Tray Support acks Top View Vertical Tray Hanger Support Field Cutting Sealant Dimension In. llowable C oad bs , , llowable load is based on a total load, uniformly distributed over the length of the rack. Safety factor = 2.0 C of 7 6 holes C C of 7 6 holes 2 hanger rod and nuts separate order items SEMKIT sive for custom fabrication or quirements for sea and ground transportation. H = Side ail Height, available heights (inches):, 4, 6, or 8; = idth of the inside distance from tray wall to tray wall Quart Can: ES-Q ester resin products. Clear color. for sea and ground transportation. CE TY SYSTEMS 27

28 Enduro channel-type instrumentation tray is designed for light loads of individual wiring and pneumatic tubing. Our channel-type tray is available with solid or ventilated bottom. ll splice plates and hardware are separate order items. Enduro s ventilated channel-type tray features allow for cooling and cable strapping. - -() x () Example: - PE x 20 EIS = Solid ottom PE = Polyester 200 = 2 0 = = 6 600D = = = 0 Channel Size idth x Depth bs./ft. Channel Thickness Span Ft. (m) Max oading bs./ft. (N/m) Max Deflection In. (mm) 2 x (5 x 25) (4.76) 5 (.5) 4.0 (5.94) 0.5 (2.7) x (76 x 25) (4.76) 5 (.5).9 (5.79) 0.5 (2.7) 8 (2.4).0 (.48) 0.8 (20.) 4 x 8 (02 x 5).05 8 (2.4) 2.8 (4.6) 0.8 (20.) 4 (6.5) 0 (.0).5 (2.2).0 (25.4) 6 x 5 8 (52 x 4) (6.5) 0 (.0) 2.8 (4.6).0 (25.4) 8 x 4 (20 x 44) (7.94) 0 (.0) 5.2 (7.7).0 (25.4) 0 x 2 4 (254 x 70) (.0) 20.0 (29.7).0 (25.4) 8 (9.5) 5 (4.5).9 (5.79).0 (25.4) 20 of the span. NOTE: mm values are nominal; * In Key, parentheses ( ) = insert corresponding option code; = ottom; inside distance from tray wall to tray wall 28 CE TY SYSTEMS

29 adius 8 (457) 22 4 (578) 24 (60) 28 6 (729) 24 (60) 28 4 (70) 22 4 (565) 4 4 (820) which can be 2,, 4, dimensions contact us Vertical Outside Molded adius 2 (05) 6 4 (4) 24 (60) (79) 24 (60) 28 4 (78) 24 (60) 28 6 (76) 90 adius 2 (05) 22 4 (578) 24 (60) 2 6 (8) 24 (60) 4 4 (88) 24 (60) 6 6 (92) Vertical Outside Mitered 22 (559) 4 (864) (60) 25 (65) 26 (660) 28 (7) 0 (762) 2 (8) 6 (94) 7 (940) 8 (965) 40 (06) 42 (067) 44 (8) which can be 2,, 4, dimensions contact us. () = S for solid P for Ventilated 45 PE for Polyester VE for Vinyl Ester NOTE: mm values are nominal; * In Key, parentheses ( ) = insert corresponding option code; inside distance from tray wall to tray wall CE TY SYSTEMS 29

30 2 2 (5) 2 (5) (76) (76) 4 (02) 4 (02) 6 (54) 6 (54) 8 (20) 8 (20) 0 (255) 0 (255) 2 2 () = S for solid P for Ventilated PE for Polyester VE for Vinyl Ester 8 (457) 8 (457) 8 (457) 8 (457) Channel Tray Cover other resin part numbers, contact us. 6 (5) 4 bolt Channel Cover Clamp 2 (5) resin part numbers, contact us. Channel Hold Down Clip IHDC- (76) 8 (28) IHDC-4 4 (02) 4 () IHDC-4D 4 (02) IHDC-6 6 (54) 4 (44) (25) 2 () IHDC-6D 6 (54) IHDC-8 8 (20) 7 8 (47) IHDC-0 0 (255) (72) 2 (8) = idth of the inside distance from tray wall to tray wall 0 CE TY SYSTEMS

31 Channel-Type Splice Plate Part Numbers Example: space in product number blank, Splice plates and hardware are sold individually and are not provided with and Degree, example: EISP-X For Vinyl Ester esin For Halogen-Free Polyester esin, For Stainless Steel These part numbers are for Polyester resin. Dimensions Channel Depth Inches (mm) Inches (mm) Inches (mm) 2 (5) (25) 4 (6.5) (76) (25) 4 (6.5) 4 (02) (25) 4 (6.5) 6 (52) 4 (2) 5 8 (5.875) 8 (20) 4 (2) 5 8 (5.875) 0 (254) 2 4 (57) 8 (28.575) Hardware 4-20 x SS 4-20 x SS 4-20 x tray except 0. Contact us for bolt sets for monel. Contact us for pricing and availability. Straight Section (225) ø (8) holes 4 8 (05) 4 (2) 6 4 (56) Expansion 90 Vertical 45 Vertical 5 6 ø x (8 x 25) slots (225) 6 (52) 0 Vertical 22.5 Vertical 4 (2) 6 4 (56) 4 8 (05) 4 (2) 2 4 (2) 6 (52) (64) 4 (2) 4 (2) (24) 45 4 (2) (6) (24) (24) 5 8 (6) 4 (2) 45 4 (2) (2) (24) (24) (24) CE TY SYSTEMS

32 Made from the same high-strength, corrosion-resistant pultruded materials as our ladder-type tray, Enduro instrumentation tray is tough and made to stand up to the most demanding environments. of solid or perforated bottom, and with or without snap-on covers. Perforated cable trays are pre-slotted for ventilation or easy attachment of cables. - widths come in 50mm, 00mm, 50mm and 00mm, measuring inside to inside of the - Flanged-Type Straight Section Part Numbers - - (H) - CT - () - () Example: EP CT M Side ail Smoke Plus *Slot size: 7 6 (25.40mm) x 6 (4.76mm) +/- Technical Data - Flanged Tray Maximum oading Span Max oading Ft. (m) bs./ft. (N/m) 5 (.5) 25.7 (4.8) 0 (.0). (4.2) 5 (4.5) 0.9 (.2) 5 (.5) 0.9 (4.9) 0 (.0).8 (5.2) 5 (4.5). (.5) 5 (.5) 5.6 (48.) 0 (.0) 4.4 (6.0) 5 (4.5). (.8) 5 (.5) 42.4 (57.5) 0 (.0) 5.2 (7.) 5 (4.5).5 (2.0) 5 (.5) 54.2 (7.9) 0 (.0) 6.7 (9.) 5 (4.5) 2.0 (2.7) 5 (.5) 94.4 (28.0) 0 (.0).8 (6.0) 5 (4.5).5 (4.7) 5 (.5) 08.4 (47.0) 0 (.0).5 (8.) 5 (4.5) 4.0 (5.4) 5 (.5) 0.8 (77.) 0 (.0) 6.4 (22.2) 5 (4.5) 4.8 (6.5) ccessories & Splice Plates Straight Cover Example: E-IT-50-CTC-M Covers only available in m lengths. Straight Splice Plates Material Stainless Steel Polyester Vinyl Ester Polyester Example: E-IT-80-SSP educer Splice Plates Please specify idth and idth 2 when ordering. Material Stainless Steel Fiberglass = idth of the inside distance from tray wall to tray wall 2 CE TY SYSTEMS

33 Example: Flanged-Type Fittings Part Numbers - -(H)-TYPE-()- - () E H Side ail *Slot size: Smoke Plus 6 (6.525) x ¼ (6.5) +/- Note: More fittings and fitting covers available, please contact us. 90 Vertical Outside Mitered (49) 2 8 (54) (59) 29 4 (74) 27 6 (688) 28 2 (72) (758) 4 6 (865) Cover Note: More fittings and fitting covers available, please contact us. * In Key, parentheses ( ) = insert corresponding option code; inside distance from tray wall to tray wall 9 6 CE TY SYSTEMS

34 ireway Enduro wireway is designed to protect data control, communication and power cables from atmospheric - often found in: Computer, communication, and clean room applications. utilize caustic disinfectants - enhanced public safety Enduro lay-in-wireway is manufactured by the pultru- - strength, durability, and corrosion resistance. dance with STM Standard E modular design which includes straight sections, elbows, tees and crosses. covers come in 0 ft. lengths. Splice plates are a separate order item. C 250 x 0 C 404 x 0 C 42 x (64mm) 2 2 (64mm) 4 (02mm) 4 (02mm) 4 (02mm) 2 (05mm) ireway 6 (52mm) C 606 x 0 6 (52mm) 6 (52mm) 6 (52mm) C 62 x 0 6 (52mm) The C 62 x 0 is available with or without a divider. The divider allows separation of various cables as needed. 8 E 8 C 250 x 0 C 404 x 0 Dimension Inches (mm) C D E N/ 2.5 (64) 2.5 (64) (76) N/* 6 (8) 4 (02) 4 (02) 4 4 (2) 5 8 (6) Pultruded FP/GP ireway Cover D FP/GP ireway Cover Splice Plate Deep C 42 x 0 6 (8) 4 (02) 2 (05) 2 4 (24) 8 (40) C 606 x (4) 6 (52) 6 (52) 6 4 (7) 7 8 (87) C 62 x (4) 6 (52) 2 (05) 2 4 (24) 8 (40) * Cover body and splice plates not available for C250. See page 7 for splicing method FP/GP ireway ody Splice Plate C 4 CE TY SYSTEMS

35 ireway ireway oad Span C250 x 0 C404 x 0 C42 x 0 C606 x 0 C62 x 0 Maximum Span Maximum oading contact us contact us 0 (m) 0 bs/ft (4.9 kg/m) 0 (m) 2 bs/ft (7.9 kg/m) 0 (m) 20 bs/ft (29.8 kg/m) 0 (m) 25 bs/ft (7.2 kg/m) ireway Physical Properties Electrical Property Polyester Fire STM etardant Test Electric Strength, Short Term in Oil 8, VPM* 200 D49 Electric Strength, Short Term in Oil, KV per inch 5 D49 Other Property Polyester Fire STM etardant Test Density - Solid Shape bs./in D792 ater bsorption (24 Hr. Immersion) Max % by t D570 Surface urning Characteristic, Maximum 25 E84 Property C H C H C 42-90H C H C 62-90H 8 (20) 2 6 (25) 2 (5) 5 (8) 2 (5) Thermal Polyester Fire STM etardant Test Thermal Coefficient of Expansion (Inches/Inch/ F)** 5 x 0-6 D (267) 2 (05) 2 (05) 4 (56) 4 (56) Depth Plan View idth 8 (20) Side View Depth 8 (20) ongitudinal Direction Property Polyester Fire STM etardant Test Ultimate Tensile Strength 0,000 PSI D68 Ultimate Compressive Strength 0,000 PSI D695 Ultimate Flexural Strength 0,000 PSI D790 Transverse Direction Property Polyester Fire etardant Ultimate Tensile Strength 7,000 PSI Ultimate Compressive Strength 5,000 PSI Ultimate Flexural Strength 0,000 PSI * Specimen tested perpendicular to laminate face. STM E84. C H-2 C H-2 C 42-90H-2 C H-2 C 62-90H (572) 6 (808) 24 6 (60) 5 (889) (88) (8) 27 (686) 8 8 (968) (88) (8) (446) 24 6 (60) 8 8 (460) 25 6 (652) 8 8 (460) 25 6 (652) 8 8 (460) 25 6 (652) 8 8 (460) 25 6 (652) Depth Plan View idth adius Side View ireway CE TY SYSTEMS 5

36 Fittings - ireway 90 Vertical Outside Direct end 90 Vertical Outside end 2 adius Side View Side View 0 2 (267) 9 6 (487) 27 8 (689) 2 (05) 2 (562) 8 (797) Depth 2 (05) 4 (56) 8 (20) 2 (562) 8 (797) 24 6 (64) 4 6 (868) 4 (56) Depth 24 6 (64) 4 6 (868) 45 Vertical Outside Direct end 45 Vertical Outside end 2 adius Side View Side View 8 6 (205) 0 (254) 0 (254) 2 (05) Depth 8 (20) (252) 2 8 (54) 2 (05) (595) 2 (05) (595) 4 (56) 25 (65) Depth 2 (05) 4 (56) 25 (65) C H C H C 42-45H 8 6 (205) 0 2 (267) (47) 8 (20) Plan View idth C H-2 C H-2 C 42-45H (4) (657) 8 6 (205) 28 8 (72) 6 6 (4) (878) Plan View C H (2) C H (259) 0 (762) C 62-45H (47) C 62-45H (4) (878) 8 6 (205) Side View 8 (20) 0 8 (257) 2 6 (55) Side View ireway 0 8 (264) 0 8 (264) 6 (284) 6 (284) Depth 5 6 (287) 2 4 (552) 5 6 (287) 2 4 (552) 2 4 (24) 2 4 (552) 2 4 (24) 2 4 (552) 8 (20) Plan View Plan View C 250-HC C 404-HC C 42-HC 8 2 (470) (524) 28 4 (70) C 250-HT C 404-HT C 42-HT 0 2 (267) 8 2 (470) (0) (524) 2 (5) 28 4 (70) C 606-HC C 62-HC 22 4 (578) 28 4 (70) C 606-HT C 62-HT 5 (8) 22 4 (578) 2 (5) 28 4 (70) Plan View Plan View C 250-HC (07) C 250-HT (572) 42 4 (07) C 404-HC () C 404-HT (60) () C 42-HC-2 C 606-HC-2 C 62-HC (40) 46 4 (87) 52 4 (40) C 42-HT-2 C 606-HT-2 C 62-HT (87) 52 4 (40) (684) 46 4 (87) (87) 52 4 (40) 6 CE TY SYSTEMS

37 Cover ody & Splice Plates ireway C Hold Down Splice Joint C 404 x SP04 C 42 x SP04 C 606 x SP04 C 62 x SP04 F G Hole Dia. 6 (8) 4 (44) () 6 (8) 4 (44) () 5 8 (6) 2 (8) (67) 7 6 () 5 8 (6) 2 (8) (67) 7 6 () Includes snap-on cover splice plate and bottom plate with 04SS fasteners. If 6SS is required, substitute 6 for 04 in part number. Cover ody C250-C04 C404-C04 C42-C04 C606-C04 C62-C04 dual purpose splice plate that offers hold down capabilities. Easily adaptable to other material color is gray. Contact us for details regarding a custom color. If 6SS is required, substitute 6 for 04 in part number..5 (8) ireway ody.75 (9). (29).75 (9) 2 (5) G Splice Plate F (5) Closure Plate C P contact us contact us C CP04 Example: C 404-CP-6 C P 0 4 (260) 0 8 (264) C CP04 C 42 - P 8 4 (46) 0 8 (264) C 42 - CP04 C P 2 4 () 2 8 (4) C CP04 C 62 - P 8 4 (46) 2 8 (4) C 62 - CP04 Top plate removable for easy access. 2 Typ 2 Typ ireway.0 General power, control and instrumentation cables..2 ireway shall be solid bottom type construction with minimum wall thickness of.875 inches.. Cover and cover splice plates shall be snap-on type construction requiring no installation fasteners. 2.0 Standards 2. The wireway system shall conform to the applicable supports at greater intervals, but in no case shall the distance between supports exceed 0 feet..0 Materials. The wireway, cover, and splice plates shall be made inhibiting additives and exterior veil coverage. able.. ll composite material shall meet STM E84, maximum.4 Color shall be gray. 4.0 oading Capabilities CE TY SYSTEMS 7

38 Support Systems & Strut Channel Framing (Solid & Punched) Polyester: EC-0 bs/ft Polyester: EC-58 bs/ft Polyester: EC-58D bs/ft () 4 (9) 7 6 () 7 6 () 4 (9) 7 6 () 9 2 (7) (25) 9 2 (7) 5 8 (4) 4 (8) 5 8 (4) 5 8 (4) 9 2 (7) 5 8 (4) (25) example: EC-0H. Punched not available for double channel. Punched tying down cable. vailable in 0 ft and 20 ft lengths. See below for 7 6 () 4 (9) 5 8 (4) 7 6 () 9 6 (4) 9 6 (4) 2 (5) Support Systems Technical Data - Support Systems & Strut Channel Framing oading eam and Column Data: Polyester and Vinyl Ester esin ase eam Span or Column Height In.(mm) 2 (05) 8 (457) 24 (60) 0 (762) 6 (94) 42 (067) 48 (29) 60 (524) 72 ( (24) 96 (248) Part Maximum Deflection Uniform oad Uniform oad Maximum No. Maximum Maximum Deflection llowable Uniform llowable = 0.25 In. (6mm) = 0.50 In. (mm) Column eam oad Uniform eam oad oad Poly Vinyl Poly Vinyl Poly Vinyl Poly Vinyl. EC-0 bs.(kg) 790 (58) bs.(kg) 990 (449) In.(mm) 0. () In.(mm) 0.2 () bs.(kg) - bs.(kg) - bs.(kg) - bs.(kg) - bs.(kg) 2550 (56) EC (780) 250 (975) 0.07 (2) 0.07 (2) (655) EC-58D 5080 (20) 650 (2880) 0.04 () 0.04 () () EC-0 50 (240) 670 (04) 0.24 (6) 0.27 (7) (28) (066) EC (52) 440 (65) 0.5 (4) 0.7 (4) (528) EC-58D 5080 (20) 4240 (92) 0.09 (2) 0.0 (2) (058) EC (8) 500 (227) 0.4 () 0.48 (2) 240 (09) 270 (22) (99) EC (90) 080 (490) 0.27 (7) 0.0 (8) 80 (67) 90 (42) (42) EC-58D 2540 (52) 80 (442) 0.6 (4) 0.7 (4) (2685) EC-0 20 (45) 400 (8) 0.67 (7) 0.75 (9) (6) 240 (09) 270 (22) 70 (775) EC () 870 (94) 0.42 () 0.48 (2) 40 (86) 460 (209) () EC-58D 2040 (925) 2550 (56) 0.24 (6) 0.27 (7) 2000 (907) 250 (066) (2222) EC (22) 40 (54) 0.98 (25).0 (28) 70 () 80 (6) 40 (6) 60 (72) 260 (57) EC (26) 70 () 0.6 (5) 0.69 (9) 240 (09) 270 (22) 480 (27) 540 (245) 800 (86) EC-58D 700 (77) 20 (966) 0.5 (9) 0.9 (0) 220 (55) 70 (62) (6) EC-0 20 (04) 290 ().2 (4).49 (8) 50 (22) 55 (25) 00 (45) 5 (52) 920 (47) EC (222) 620 (28) 0.82 (2) 0.92 (2) 50 (68) 70 (77) 00 (6) 40 (54) 20 (598) EC-58D 460 (662) 80 (80) 0.48 (2) 0.62 (6) 770 (49) 870 (94) 50 (650) 720 (50) 2640 (97) EC (9) 250 ().72 (44).92 (49) 0 () 25 (6) 60 (27) 70 () 700 (7) EC (95) 540 (245).07 (27).20 (0) 00 (45) 5 (52) 200 (90) 20 (04) 00 (458) EC-58D 270 (576) 590 (72) 0.62 (6) 0.69 (7) 520 (26) 590 (267) 040 (47) 70 (780) 2020 (96) EC-0 60 (72) 200 (9) 2.68 (68) 2.99 (76) 20 (9) 2 (0) 40 (8) 45 (20) 80 (8) EC (58) 400 (200).70 (4).9 (48) 60 (27) 70 (2) 20 5 (6) 260 (8) EC-58D 020 (462) 280 (580) 0.97 (25).09 (28) 270 (22) 0 (40) 540 (245) 60 (276) 520 (25) EC-0 40 (6) 80 (8) * * 0 (4) 2 (5) 20 (9) 2 (0) - EC () 70 (68) 2.44 (62) 2.78 (7) 0 () 4 (5) 60 (27) 70 (2) - EC-58D 850 (85) 070 (485).40 (5).57 (40) 60 (72) 80 (8) 20 (45) 60 (6) - EC (68) * * N - 2 (5) 5 (7) - EC () 20 (45) * * 20 (9) 2 (0) 40 (8) 45 (20) - EC-58D 70 () 920 (47).9 (48) 2.5 (55) 00 (45) 5 (52) 200 (90) 20 (04) - EC-0 00 (45) 0 (59) * * N EC (00) 250 () * * (6) 5 (7) 26 (2) 0 () - EC-58D 640 (290) 800 (6) 2.50 (6) 2.79 (7) 70 (2) 80 (6) 40 (6) 60 (72) - * Deflection is in excess of.00 In. (76mm); mid-span support is recommended. N = Not ecommended; eam oads: Table lists the total allowable load for various simple spans based on a minimum safety factor 2:. If load is concentrated at center of span, multiply the load from the table by 0.5 and the corresponding deflection by 0.8. Column oads: Table lists the total allowable axial load for various unsupported column heights based on a minimum safety factor of :. Eccentric loads should be reduced according to standard practice. Notes: ll beams should be supported in a manner to prevent rotation at supports. ong, deep beams should be tied between supports to prevent twist. 8 CE TY SYSTEMS

39 Support Systems & Strut Connector Plates 5 8 ased on individual applications, changes may be required on dimension and thickness of material. Please contact us. Holes are drilled to accept 8 and 2 bolts Universal ngle Polyester: CP-50 Polyurethane: CP-PU-50 CP-00 CP-0 CP-02 CP CP-04 CP-05 CP-09 CP-0 CP CP-2 CP- CP-4 CP-5 CP CP-7 7 CP CP CP required for CP-205 CP-205 Support Systems CP-209 CP-20 CP-2 CP-226 CP-405 NOTE: These composite angle components will not support tensile loads or forces. CE TY SYSTEMS 9

40 Support Systems & Strut Post ase Polyester: PD-PE Polyurethane: PD-PU ll holes 7 6 () Polyester: PS-PE Polyurethane: PS-PU indow Clamp C-58 Stainless steel set screw included 2 (8) 6 2 (65) 5 (27) (76) ll holes 7 6 () 5 (27) 5 (27) (76) 2 4 (70) 4 (02) 4 (44) 2 (89) 6 (27) Fiberglass Clevis Hanger FP/GP Channel Nut Pipe Size Hanger O.D. Hanger od Dia. oad lbs. CH-00 2 to CH-05 4 to CH to CH to CH to temperatures. Tolerance is 4 Hanger rod mounting hole Max. Pipe OD Size eight t bs/c 6 (27) bs/c 6 (27) bs/c 6 (27) locking and designed for use with EC-58 and EC-58D strut only. Pull out strength = 700 bs. per bolt t Support Systems * Includes nylon bolt Conduit Outside Diameter Inches (for reference only) Pipe t./ PVC PVC igid Fiberglass Size 00 Sets* Schedule Coated Steel (FP/GP) Inches bs. 40 & 80 Steel Made from a toughened grade of glass reinforced polycarbonate resin. Standard fasteners are nylon - contact us. Packaged 0 sets per bag. If stainless steel fasteners are preferred, indicate Diagram: FP/GP Channel Nut with Hold Down Clip Hex Nut Flat asher Hold Down Clip Stud Strut Self-ocking Channel Nut 40 CE TY SYSTEMS

41 Enduro s DuroStrut combined with our cable tray accessories are functional in many non-cable tray applications. mounted. Enduro can also assist in engineering to your requirements. The information published are guideline bly at site. If you need a special shape or assembly, call Enduro for information on custom pultrusions and fabrications. Clevis Hanger Channel Framing (EC58D) Channel Framing (EC58) Pipe Clamps Strut Post ase Connector Plates Multi-Tiered Support acks.0 Scope 2.0 Standards less, and the Smoke Developed Index shall have a density of 450 or less when tested in accordance with class material in the Uniform uilding Code 2.2 ll channel shall have a surfacing veil over the entire to protect against degradation from ultra-violet light..0 Materials. ll channel shall be manufactured by the pultrusion pro-.2 ll channel shall conform, as a minimum requirement, est version of the Enduro technical catalog. 4.0 Non-Metallic Pipe Clamps 4.2 ll pipe clamps interlock with the channel framing described above. accommodate a Fasteners nylon, 6 stainless steel, or pultruded vinyl ester rod with ground threads and compression molded vinyl ester nuts. 6. DuroStrut is manufactured and fabricated exclusively by Enduro Composites, Inc. - Houston, TX. Support Systems CE TY SYSTEMS 4

42 Fastener & Hanging Systems Enduro fastener and hanging systems are exceptionally strong non-metallic mechanical systems with outstanding shear and tensile strengths. This makes the Enduro fastener system an excellent choice for all structural, FP/GP Threaded od FP/GP Hex Nut Size eight bs/ft bs/ft bs/ft the standard. vailable in 8 ft. lengths. Size eight t bs/c 5 8 (6) 7 8 (22) bs/c 5 8 (6) 7 8 (22) bs/c 7 8 (22) 4 (2) the standard. t bs/ft bs/c 7 8 (22) 4 (2) bs/ft bs/c 4 (2) 2 (5) FP/GP Flat asher Size eight 8-6. bs/c 2 -. bs/c 2 (5) 8 () FP/GP od Coupler Size 8-6 eight 7.80 bs/c t 2 (5) bs/c 2 (5) t bs/c bs/c bs/c bs/c 2 (5) bs/c 2 (5) bs/c 2 4 (70) the standard. thread engagement must be 4 per side. eam Clamps Description Single for 8 FP/GP Threaded od Single for 2 FP/GP Threaded od Double for 8 FP/GP Threaded od Double for 2 FP/GP Threaded od Ultimate load = 00 bs SS set screws included with clamps. Double Typical Properties - FP/GP Threaded od Hanging Systems Properties 8-6 UNC 2- UNC 5 8- UNC 4-0 UNC -8 UNC Thread shear strength using FP/GP hex nut in tensile - bs.,250 2,200,00 4,500 6,500 Transverse shear on threaded rod - double shear (load b.) (STM-565),000 5,000 7,500 2,000 22,000 Transverse shear on threaded rod - single shear (load b.),600 2,600,800 6,200 5,000 Compressive strength longitudinal, PSI (STM-D695) 54,000 54,000 54,000 54,000 65,000 Flexural strength, PSI (STM-D790) 55,000 55,000 55,000 55,000 60,000 Flexural modulus, PSI x 0 6 (STM-D790) Torque strength using fiberglass nut lubricated with SE 00 motor oil, Ft.-bs Dielectric strength, KV/In. (STM-D49) ater absorption 24 hour immersion - threaded, % (STM-D570) Coefficient of thermal expansion - longitudinal In./In./ F 5 x x x x x 0-6 Max recommended operation temp - based on 50% retention of ultimate thread shear strength F ( C) 200 (9 ) 200 (9 ) 200 (9 ) 200 (9 ) 200 (9 ) Stud weight, b./ft Flammability Self-extinguishing on all reduced values. Proper safety factors should be applied to testing. ll values are based on laboratory test results. 42 CE TY SYSTEMS

43 make it ideal for many applications where high strength, non-metallic fasteners are required. Thread Shear Maximum Socket Size (single nut) Installation Size Torque 8-6 UNC,250 bs. 4 Ft.-bs UNC 2,200 bs. 8 Ft.-bs UNC,00 bs. 6 Ft.-bs UNC 4,500 bs. 24 Ft.-bs UNC 6,500 bs. 50 Ft.-bs. 2 If the assembly will require occasional removal of the nuts, the rod should be lightly coated with a dry lubricant, silicon spray, or a light oil prior to assembly. If the assembly is designed to be a permanent installation, the nuts and studs should be bonded with an epoxy adhesive. Maximum installation torque of 0 foot-pounds is recommended to secure set screw. Site Conditions duro fastener assembly should be eliminated or mini- should be used in designed the fastener system. Tools equired quires a larger than normal socket wrench, but either a six point or twelve point socket will work. Important - do not exceed the torque values listed in the table above. Caution Fastener & Hanging pply a light coating of adhesive to the stud and nut threads, then quickly secure the assembly before adhesive has time to set, otherwise the mil thickness of apply a thick coat of adhesive to the exposed stud and nut surfaces. This provides a locking mechanism which eliminates the need for extra torque and lock washers. The optimum method of installation for a hanger sys- cedure whenever possible. This results in minimum torque and allows maximum thread shear. To insure maximum resistance to chemical attack once the assembly is completed, the exposed stud thread consideration must be given to reduced strengths. Enduro rod and nuts are designed with maximum thread engagement and extra nut thickness. Metal products have less thread engagement. hen installation requires metal components, special tests may be neces- tems. Do not over torque the Enduro nut and rod. The clusive, they are additive Example 2 - has a thread shear of 2,200 bs. and an ultimate torque strength of 8 ft-lbs. If you use the maximum installation torque of 8 ft-lbs, the amount of thread shear remaining is reduced to,225 lbs. Specifying engineers should apply this information at the design stage, applying the proper safety factors to ensure a secure installation. Typical Hanging Support System Cover Cable Tray Hold Down Clip Hanging Systems CE TY SYSTEMS 4

44 with most metallic systems Floor Mount Single Column or all Mount ighter weight with corrosion resistance comparable minimum Compatible with metallic post bases and metallic support structures Easily built on site allowing for design freedom and increasing response time Constructed from 2 Schedule 80 gray vinyl ester base for superior corrosion resistance Floor Mount Double Floor Mount Triple C C D C Pushbutton Station forced vinyl ester 2 square tube with an 8 square vinyl ester base dimensions in inches. * In Key, parentheses ( ) = insert corresponding dimension C EU050 EU070 EU00 EU25 EU50 EU200 EU250 EU00 EU50 EU400 Pipe Nom. Dia. C D T Max ec. Max ec. oading bs. Torque In.-bs Made from glass reinforced polyurethane resin, u-bolts are the ideal choice for mounting enclosures, instrumentation, conduit, and piping on your Enduro instrument and pushbutton support systems. Excellent as an alternative when replacing corroded steel u-bolts. T C D 44 CE TY SYSTEMS

45 Notes CE TY SYSTEMS 45

46 Other Enduro Engineered FP/GP Products Enduro Environmental Products FP/GP Tank Cover Compression Sealed for Effective Odor Control ccess ess Headspace Over ater for all standard 6 Easy Installation FP/GP & Dual aminate Pipe & Vessels sels from to 60. Enduro can virtually source any resin required for your panies like Dow Chemical for over 50 years. FP Products For ight ail & Mass Transit Systems Enduro third rail cover boards are custom designed to provide safety by lightweight pultruded composites. Enduro has exceeded the most stringent of technology that provides the highly desired low smoke development and low toxicity characteristics preferred by transportation safety authorities. 46 CE TY SYSTEMS

47 Other Enduro Engineered FP/GP Products Enduro uilding Products Enduro FP/GP uilding Panels uilding Panels ronmental conditions, Enduro Tuff Span liver unsurpassed performance as in- Strength stiffness is determined by the align- inforcements. Tuff Span is constructed with high reinforcing content placed in straight and continuous, bidirectional alignment. s a result, Tuff Span has higher strength and stiffness of any history of standing up to hurricane winds where aged metal, cementious, and other materials have failed. Corrosion esistance To resist attack from aggressive chemical exposure, Tuff Span is formulated with premium resin systems, is provided by an exterior acrylic coat- resin-rich surface, and interior mat or veil. Opaque Colors hite eige Stone hite Shale Translucent Colors eige Daylight lue Shale Enduro has the ability to produce colors matched to coating protection surface & surfacing mat bi-directional reinforcements ( layers) retardant resin system Enduro Tuff Span FP/GP panels are the strongest of any More Enduro Tuff Span Products ouvers Tube idge Vents ide Flange Gutter Systems Flat Plate Sections Enduro FP/GP structural members at a water treatment plant Enduro FP/GP primary & secondary beams FP Products Channel Enduro FP/GP louvers on an offshore platform off the Gulf Coast Enduro FP/GP idge Vent CE TY SYSTEMS 47