Operator Enclosures. Console Type 12 - AW-14 Data Sheet
|
|
- Ginger Sharp
- 5 years ago
- Views:
Transcription
1 Console Data Sheet Construction Console body, panel cover and door, top assembly and writing desk are fabricated from (14) gauge steel ll continuous welded seams are finished smooth Panel cover is secured to the body with a continuous hinge along the front side and captive screws which thread into sealed well nuts on the other three sides Cover stops allow the panel cover to be held in the open position Consoles 36 inches wide or less have a single front and rear access door with a heavy-duty continuous hinge on one side and a 3-point locking handle on the opposite side Consoles wider than 36 inches have double front and rear access doors with a heavy-duty continuous hinge and a center locating 3-point locking handle which closes right side door over left Mounting s are welded inside for locating optional panel along console depth Front door has a print pocket Panel cover, front door and top assembly covers have fixed oil-resistant gaskets Optional top assembly has front mounted instrument panel cover(s) and rear mounted access panel cover(s) n optional writing desk is available with convenient front pplication Houses electrical controls and instruments Designed with a 60 angle top surface for pushbuttons, pilot lights, switches or other monitoring devices Protects against circulating dust, falling dirt and dripping non-corrosive liquids Standards UL 508 listed, Type 12 CS C22.2 No.94 certified, Type 12 Conforms to NEM standard for Type 12 Finish Wash and phosphate undercoat Console body has an NSI 61 gray polyester powder outside with a white polyester powder finish inside Optional top assembly and writing desk have an NSI 61 gray polyester powder finish ccessories NEM terminal strap kit Terminal blocks Swing panels Full and half panels Channel hardware Caster kit Touch-up paint Replacement handle, 25228C, see page 421 See ccessories section Notes: Cooper -Line can provide special sizes, finishes and other modifications. Consult the factory for your special requirements. 361
2 Console Illustration Sheet and Catalog Number Console ody Console ody Size Top ssembly Writing Desk Height x Width x Depth Optional Optional x x C Catalog Number in. mm Catalog Number Catalog Number C x x x 610 x 584 C-1424T C-1424W* C x x x 914 x 584 C-1436T C-1436W* C x x x 1219 x 584 C-1448T C-1448W* C x 60.00x x 1524 x 584 C-1460T C-1460W* C x x x 1829 x 584 C-1472T C-1472W* * Not UL or CS listed (318) captive screw panel cover continuous hinge (813) 3-point handle lock 6.75 (171) Console ody Front View (24 inch & 36 inch wide body) print pocket (supplied) C Side View (457) (121) Panel Cover Opening (panel cover removed) 3.37 (86) Console ody Rear View 362
3 Console Illustration Sheet (318) panel cover captive screw (813) continuous hinge 3-point handle lock 6.75 (171) print pocket (supplied) C Console ody Front View (48 inch wide body) Side View (457) (121) Panel Cover Opening (panel cover removed) 3.37 (86) Console ody Rear View 363
4 Console Illustration Sheet (318) panel cover captive screw (813) continuous hinge 3-point handle lock 6.75 (171) Console ody Front View (60 inch & 70 inch wide body) print pocket (supplied) C Side View (457) /2- / (121) Panel Cover Opening (panel cover removed) 3.37 (86) Console ody Rear View 364
5 Console Illustration Sheet (318) (406) instrument panel cover captive screw access cover Top ssy Front View (24 inch (610 mm) & 36 inch (914 mm) wide body) Side View (typical all top assy) Top ssy Rear View (24 inch (610 mm) & 36 inch (914 mm) wide body) (406) Top ssy Front View (48 inch (1219 mm) wide body) Top ssy Rear View (48 inch (1219 mm) wide body) (406) Top ssy Front View (60 inch (1524 mm) & 72 inch (1829 mm) wide body) Top ssy Rear View (60 inch (1524 mm) & 72 inch (1829 mm) wide body) (254) Writing Desk Front View (* not UL or CS listed) Side View 365
6 Console ccessories Full and Half Panel Illustration Sheet and Catalog Number Full Panel Panel Panel Size Fits Height x Width Console ody x Catalog Number in. mm Catalog Number C-1424P x x 505 C-1424 C-1436P x x 809 C-1436 C-1448P x x 1114 C-1448 C-1460P x x 1419 C-1460 C-1472P x x 1724 C Half Panel Panel Panel Size Fits Height x Width Console ody x Catalog Number in. mm Catalog Number C-1424HP x x 505 C-1424 C-1436HP x x 809 C-1436 C-1448HP x x 1114 C-1448 C-1460HP x x 1419 C (978) panel side bracket (see detail sheet page 368) Half Panel (upper mount) Full Panel Half Panel (lower mount) Full Panel Mounting Half Panel Mounting Full panel and half panel for consoles are (12) gauge steel and furnished with panel brackets and all hardware necessary for and panel. Half panels can be mounted in either the upper or lower portion of the console. Console body design permits the panel to adjust along the depth of the enclosure. Full panel and half panel can be mounted back-to-back. 366
7 Console ccessories Swing Panel and Terminal Strap Kit Illustration Sheet and Catalog Number Swing Panel Panel Panel Size Fits Console ody Height x Width x Catalog Number in. mm Catalog Number C-1424SWP x x 476 C-1424 C-1436SWP x x 781 C-1436 Terminal Strap Kit Panel Quantity Fits Console ody Catalog Number of Straps Catalog Number 24TS20 4 ll W-14 Series 24TS24 5 ll W-14 Series 3.18 (81) 2.06 (52) swing panel bracket assembly (see detail sheet) panel side bracket (see detail sheet page 368) hinge Swing Panel Terminal Strap Kit Swing Panel Mounting Terminal Strap Mounting Swing Panel Mounting Swing Panel for Consoles are (12) gauge steel, have a dual hinge swing panel bracket and are furnished with panel brackets and all hardware necessary for and panel. Panels can be installed such that they hinge either on the left side or right side. Console body design permits the panel to adjust along the depth of the enclosure. The dual hinge allows the inner panel to swing completely out of the rear opening when within 5.50 inches. Panel and swing panel can be mounted back-to-back. Terminal Strap Mounting Terminal Strap Kits assemble conveniently to the on either side of the console body. Channel hardware should be purchased separately for installation. Full length straps are furnished with adequate space for the users terminal blocks or terminal blocks and extra straps can be purchased separately (see detail sheet and the ccessories section). 367
8 Console ccessories Illustration Sheet and Catalog Number Catalog Number Description Fits Illustration Quantity Console ody spring nut FSRKT1 Panel bracket W-14 Series 1 1 FCMH3 Channel hardware W-14 Series 2 3 FT3005 #18-#8 medium-duty flat base terminal block W-14 Series 3 1 FTE3001 Medium-duty flat base terminal block end W-14 Series 3 1 CT3005 #18-#8 medium-duty terminal block W-12 Series 4 1 CTE3001 Medium-duty terminal block end W-12 Series 4 1 FT6005 #18-#4 heavy-duty flat base terminal block W-14 Series 3 1 FE6001 Heavy-duty flat base terminal block end W-14 Series 3 1 CT6005 #18-#4 heavy-duty terminal block W-12 Series 4 1 CE6001 Heavy-duty terminal block end W-12 Series 4 1 CTC2 Channel clamp W-12 Series Channel Strip (72 inch) W-12 Series - 1 panel nut panel stud side bracket hardware spring nut hardware Illustration 1 Illustration 2 flat base terminal block (shown stacked) flat base terminal block terminal end Top ssembly Individual terminal block and terminal end only. Heavy and Medium-duty blocks can be stacked to any length. When stocked, each block is approximately.43 or.56 inches long, depending on which block is used. For detail and specific quantity packages, refer to the ccessories section. Illustration 3 Writing Desk clamp terminal block (shown stacked) terminal block terminal end clamp Individual terminal block, end, and clamps only. Heavy and Medium-duty blocks can be stacked to any length. When stacked, each block is approximately.43 or.56 inches long, depending on which block is used. For detail and specific quantity packages, refer to the ccessories section. Illustration 4 Console ody Typical ssembly 368
9 Console Details Panel and Console Detail Sheet console width (146) 2.87 min (73) 3.00 min (76) 2.87 (73) Console Rear ccess Door (section view showing full and half panel mounted back-to-back) console width (154) 2.87 (73) 2.87 min (73) 5.00 min (127) 3.18 (81) Console Rear ccess Door (section view showing swing panel and half panel mounted back-to-back) 369
Disconnect Enclosures
Type 12 Heavy-Duty Single & Multi-Door Data Sheet pplication Houses electrical controls and equipment Protects against circulating dust, falling dirt and dripping non-corrosive liquids Standards UL 508
More informationType 12 / 13 Enclosures
Type 12 Free-Standing Enclosures ata Sheet pplication Houses electrical controls and instruments Easy access fixed or swing panels for optional equipment ual-access construction available for back-to-back
More informationType 4 Panel Enclosures
Ground-Mount Enclosures Type 4 Free-Standing ata Sheet Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish pplication Houses electrical controls and instruments Easy access panels or
More informationCable & Wire Management
Cable & ire Management ay-in ireway Data Sheet Cable & ire Management pplication ouses runs of control and power cable Protects against circulating dust, falling dirt and dripping noncorrosive liquids
More informationType 4 Panel Enclosures
Type 4 Free-Standing ata Sheet Finish Wash and phosphate undercoat ANSI 61 gray polyester powder finish Accessories Full and half panels Side and swing panels Channel mounting hardware Equipment rack mounts
More informationType 4 Panel Enclosures
Type 4 Lift-Off Cover ata Sheet Seamless poured in place gasket Application Houses electrical controls and instruments Intended for indoor or outdoor use Protects against windblown dust and rain, splashing
More informationType 4X Panel Enclosures
Ground-Mount Enclosures Type 4X ouble-oor EnviroShield Free-Standing with 3-Point Locking ata Sheet ccessories Full and half panels Side panels Swing panels Touch-up paint Mounting legs Rack angles Swing
More informationType 4 X Panel Enclosures
Ground-Mount s Type 4X ouble-oor EnviroShield Free-Standing with 3-Point Locking ata Sheet ccessories Full and half panels Side panels Swing panels Touch-up paint Mounting legs Rack angles Swing out frames
More informationType 4 Panel Enclosures
Wall-Mount Enclosures Type 4 Premier Series with Quarter-Turn Latches Data Sheet and Catalog Number Accessories Premier panels NEMA panel adapters Depth adjustment brackets Print pockets Padlockable or
More informationUses, Certifications, and Standards Electrical Control and Instruments, Indoor/Outdoor EXTERNAL FEET, WALL standard UL 508, CSA C22.
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 121264CHC Encl 12X12X6 N4 Enclosure Cooper B-Line/Cable Tray Catalog Number Manufacturer escription Weight per unit Product
More informationType 4X Panel Enclosures
Wall-Mount Enclosures Type 4X Premier Series with Quarter-Turn Latches Data Sheet Construction Enclosure and door are fabricated from code gauge Type 304 or Type 316L stainless steel (see pages 209 & 210)
More informationCable & Wire Management
Type 1 Screw over... 8-14 Type 1 Quick-onnect inge over... 15-20 Type 3R nviroshield... 21-24 Type 12... 25-31 eed-through Wireway Type 12... 32-35 eed-through Wireway Type 4X... 36-39 Wiring Trough Type
More informationOperator System Enclosures
27 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST Saginaw Control & Engineering s Type 12 Operator Systems are designed to house a wide variety of equipment; panel mount, rack mount, desktop PC s, monitors,
More informationPushbutton Enclosures
7 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST Saginaw Control & Engineering s Type 12 are designed to house oil-tight pushbuttons, switches, and pilot lights. These enclosures are primarily used in
More informationchannel bracket 1.50 (38) flat strap shaded area is useable space
Electrical JIC Terminal Strap Kit JIC Terminal Strap Kits fit all styles and types of JIC enclosures. The kits are furnished with flat straps for mounting Flat Based Terminal Blocks, (see Flat Based Terminal
More informationCable & Wire Management
able & ire Management able & ire Management Lay-In ireway Type 1 Screw over... 8-14 Lay-In ireway Type 1 Quick-onnect inge over... 15-20 Lay-In ireway Type 3R EnviroShield... 21-24 Lay-In ireway Type 12...
More informationHeavy-Duty Enclosures Type 12 Free Standing Disconnect with Sub Panel
eavy-uty Enclosures PPLICTIONS - esigned to provide protection for electrical instruments, terminals, and controls from dust, oil, dirt and dripping liquids. CONSTRUCTION - abricated from 10 gauge carbon
More informationType 4 Panel Enclosures
Free-Standing ccessories Type 4 Single-oor Full and Half Panel Illustration Sheet and atalog Number iscount Schedule: 2 Subclass: S Full Panel (Single-oor) Panel Panel Size Fits atalog x Number in. mm
More informationType 4X Panel Enclosures
Type 4X Lift-Off Cover ata Sheet Seamless, poured in place gasket Application Houses electrical controls and instruments Intended for indoor or outdoor use where a corrosive environment exists Protects
More informationDisconnect Enclosures
Wall-Mount Enclosures Type 12 Flange-Mount....................................................................... 296-298 Wall-Mount Enclosures Type 4 & 4X Premier Series 2-Point or 3-Point Locking..........................
More informationNEMA 4 Single-Door Wall Mount Right-Flanged Disconnect SN4 Series
NEMA 4 Single-Door Wall Mount Right-Flanged Disconnect SN4 Series Applications SN4 Series Designed to house the following: Allen-Bradley Bulletin 1494V disconnect switches with flange-mounted variable
More informationSERIES 14 SINGLE DOOR CONSOLES TECHNICAL DATA
Operator System Enclosures 1 12 SAGINAW CONTROL ENGINEERING STOCK PRICE LIST SAGINAW CONTROL ENGINEERING STOCK PRICE LIST 13 Series 1 Single Door Consoles Application - Designed for electronic controls
More informationNEMA 4 and 12 Ultimate Single-Door Wall Mount Flanged Disconnect N412_CD Series
NEMA 4 and 12 Ultimate Single-Door Wall Mount Flanged Disconnect N412_CD Series Applications N412_CD Series Designed to house the following: AutomationDirect.com NEMA 1/12 Flexible shaft handle for Molded
More informationINDUSTRIAL SOLUTIONS Wallmount Enclosures...pgs IND 1-46 Wireway/Trough...pgs IND Freestanding Enclosures...pgs IND FMD Enclosures...
INDUSTRIL SOLUTIONS Wallmount s...pgs IND 1-46 Wireway/Trough...pgs IND 47-60 Freestanding s...pgs IND 61-72 FMD s...pgs IND 73-86 Operator Interface...pgs IND 87-136 Noncorrosive...pgs IND 137-193 I N
More information4412HS Wway 4X4X12 N1 HC Lay-In. Features. Material, Color, and Finish. Dimensions and Weight. Long Description. Manufacturer Information
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 ax: 936-560-4685 4412S Wway 4X4X12 N1 Lay-In ooper -Line/able Tray atalog Number Manufacturer Description Weight per unit Product ategory
More informationType 4X Panel Enclosures
Type 4 s Type 4 s Type 4 Single-Door Data and Illustration Sheet Application Houses electrical controls and instruments Intended for indoor or outdoor use where a corrosive environment exists Protects
More information133 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST
133 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST Saginaw Control & Engineering s are designed for control and instrumentation applications. They are a general-purpose enclosure intended for indoor use
More informationWall-Mount Enclosures CONCEPT Wall-Mount Enclosures
Spec-00286 H763.422.2211 763.422.2600 Wall-Mount Enclosures Wall-Mount Enclosures Wall-Mount Enclosures Wall-Mount Enclosures, Type 4 and 12 INDUSTRY STANDARDS Wall-mounting brackets required to maintain
More informationAccessories. Accessories. Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800)
Panels JIC & Small Panels, RHC Panels, Type 1 Medium Panels, NEM Panels, JIC Perforated Panels, Medium Perforated Panels, Flanged Panels, Wood ack Panels,..........................................................
More informationFree-Stand, Single or Dual Access, Type 12
Spec-00291 ree-stand Enclosures Type 12 ree-stand Enclosures ree-stand, Single or Dual Access, Type 12 INDUSTRY STANDARDS UL 508A Listed; Type 12; ile No. E61997 cul Listed per CSA C22.2 No. 94; Type 12;
More informationTABLE OF CONTENTS. Manufacturers of Quality Electrical Enclosures. Page: Page:
TABLE OF CONTENTS Page: Access Doors. 9 Aluminum (NEMA 4X) 48 Bussed Current Transformer Cabinets... 7 Current Transformer Cabinets 7 Dividers (Cabinet & Wireway).. 50 Flush Covers (for Screw Cover Boxes).
More informationThe Pushbutton Series
The The includes two separate enclosure designs, an in-line style and a multi-hole style configuration. oth are designed from fiberglass reinforced polyester and feature a continuous polyurethane gasket
More informationAccessories. Accessories. B-Line series electrical enclosures
Panels JIC & Small Panels, RHC Panels, Type 1 Medium Panels, NEM Panels, JIC Perforated Panels, Medium Perforated Panels, Flanged Panels, Wood ack Panels,...........................................................................
More informationFREE-STANDING ENCLOSURE ACCESSORIES FREE-STANDING ENCLOSURE ACCESSORIES. Swing-Out Panels. Panels (Full & Half Length) For Single-Door Enclosures
118 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST 11 ENCLOSURE Panels (Full & Half Length) For Single-Door Enclosures Panels for single-door enclosures can
More informationHuman Machine Interface Console Range Modular MPC
Console Range Modular MPC IP 66 TYPE, 12, 13 IK 10 (single door); IP 55 TYPE 12, 13 IK 10 (double door) 36 Product Catalogue 0 Material: ody and door: 1.5 mm mild steel. Rear panel: 1.5 mm mild steel.
More informationSteel Enclosures Contents
Contents 12/001 - Type S1GK and GK/SD steel enclosures for industrial control use Type CS and GKP steel enclosures for standard starters Page 12/002 12/002 Type S3GK and GK/DW weatherproof steel enclosures
More informationSTX stainless steel boxes
STX stainless steel boxes Enclosure and door manufactured from AISI 304 stainless steel (AISI 316 on request). Mounting plate manufactured from 2.5mm sendzimir sheet steel. Hinge in stainless steel. Box
More informationM-2900A Tapchanger Control Cabinet
CONTROLS M-2900A Tapchanger Control Cabinet New installations or retrofit for Cooper, General Electric, Siemens and Howard regulators NEMA 3 rated enclosures available in the following construction materials:
More informationTYPE 1 SCREW COVER WIREWAY
TYPE 1 SCREW COVER WIREWAY Construction: C & I Enclosures Type 1 Screw Cover and Hinge Cover Wireway is fabricated in accordance with U.L. specifications from code gauge steel. Wireway is furnished standard
More informationStandard Product. Type 4 Free-Stand Enclosures and Accessories
763.422.2600 Spec-00294 F763.422.2211 Free-Stand Enclosures Type 4 Free-Stand Enclosures and Accessories Free-Stand Enclosures Type 4 Free-Stand Enclosures and Accessories Free-Stand, Type 4 INDUSTRY STANDARDS
More informationDesign Standard. Purpose: Design Standard:
Design Standard Purpose: This design standard has the purpose of creating a consistent application of motor-control centers throughout the East Side Union High School District, therefore achieving a standard
More informationWall-Mount Preferred-Cutout Disconnects Preferred Cutout, Disconnects, Type 12
763.422.2600 SPEC-00245 L763.422.2211 DISCONNECT WALL-MOUNT PREFERRED-CUTOUT DISCONNECTS PREFERRED CUTOUT, DISCONNECTS, TYPE 12 Wall-Mount Preferred-Cutout Disconnects Preferred Cutout, Disconnects, Type
More informationJunction Boxes & Enclosures JBES and ECES Series: 316L Stainless Steel Enclosures Increased Safety
JBES Series Medium Voltage 11 kv ECES Series Compliance Data: ATEX - IEC: ATEX IEC CE Ex e II Ex ia IIC; Ex ib IIC T6 to T4 Ex td A21 T80 C to T130 C Ex de IIC; Ex demb IIC Operating Temperatures: -50
More informationFrame Joining Kits. Free-Stand Cabinets PROLINE Accessories
Spec-00212 Free-Stand Cabinets PROLINE Accessories Frame Joining Kits Permits joining two enclosure frames while maintaining an environmental seal. Side-to-Side Joining Kit consists of six frame nuts and
More informationClimateCab Cabinets and Accessories
Product Data Sheet ClimateCab Cabinets and Accessories» Free-standing ClimateCabs include a NEMA 12 Cabinet with M6 or tapped rails, plus a 5000-, 8000-, or 12,000-BTU digitally controlled air-conditioning
More informationCatalog Number Material Fits CONCEPT Enclosure CCPM4 Steel When A x B is equal to or less than x in. (762 x 762 mm)
SPEC-00186 CONCEPT Accessories CONCEPT Accessories CONCEPT PANEL CONVERSION KIT Conversion Kit adapts enclosure for mounting standard NEMA-style panels in CONCEPT enclosures. Bracket attaches to rear collar
More information1.6 Accessories include tool-free snap-in technology options for air flow, cable management, shelves, power distribution units, etc.
Rittal TS IT Rack Guide Specifications TS IT network server enclosure 1.0 General Description 1.1 Modular Free Standing Equipment Cabinet 1.2 Various combinations of dimensions: 1.2.1 Height: 48 /1200mm,
More informationCONCEPT Wall-Mount Enclosure Accessories
CONCEPT Wall-Mount Enclosure Accessories The CONCEPT Enclosure Group Accessory Selection Guide Steel section 4 or Stainless Steel Enclosures section 6 Steel section 4 or Stainless Steel Window-Door Enclosures
More informationTHE ENCLOSURE HARDWARE SUPPLIER
FABTECH SUPPLY THE ENCLOSURE HARDWARE SUPPLIER Our Products JIC Style Enclosures JIC Style Cover Clamp Bracket... 5 JIC Style Cover Clamp... 6 JIC Style Cover Clamp Assembly... 6 JIC Cover Clamp Screws...
More informationIMS ACCESSORIES 166 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST. End Plate. (Industrial Modular System) End Plate. Single Door Plinth Base
Modular Enclosures 166 SAGINAW CONTROL & ENGINEERING STOCK PRICE LIST End Plate Designed to provide a sealed cover for the open end of enclosures. Provides additional wiring space along the side of the
More informationRACK ANGLES OVERVIEW. Standard Product
SPEC-01200 PROLINE G2 Internal Components Rack-Mount Angles and Accessories RACK ANGLES OVERVIEW All Rack Angles have two mounting surfaces that serve as mounts for both rack equipment and rack accessories.
More informationApplications Mill Mill Mill Mill. 9007T Convertible sequence. L100 Fixed sequence. Extra heavy duty contact ratings. Extra heavy duty contact ratings
Selection Guide Severe Duty Mill and Foundry Switches pplications Mill Mill Mill Mill Design 9007T Convertible sequence L0 Fixed sequence L14 Single Cable Pulls Fixed sequence L525 elt Conveyor Fixed sequence
More informationELECTRICAL ENCLOSURES AND MODULAR CABINETS EXM MANUFACTURING LTD. Since 1975
www.exmweb.com ELECTRICAL ENCLOSURES AND MODULAR CABINETS 19 EXM MANUFACTURING LTD. Since 1975 NEMA 12-13 SAFETY DISCONNECT 9500 UxD Right flange mounted disconnect multi-door enclosure The 9500 UxD oil
More informationPolymas Watertight PK Enclosures Product Drawings Last Updated 1/6/2006
PHOENIX MECNO COMPNY PK Enclosures Product Drawings Last Updated 1/6/2006 Rose+Bopla Enclosures 7330 Executive Way Frederick, MD 21704 301-696-9800 www.rose-bopla.com customerservice@rose-bopla.com For
More informationINDUSTRIAL ELECTRICAL AND EXPLOSIONPROOF ENCLOSURE SYSTEMS
ADALET A SCOTT FETZER COMPANY INDUSTRIAL ELECTRICAL AND EXPLOSIONPROOF ENCLOSURE SYSTEMS #NCAT01 REV. D FOR CENELEC APPROVED UNITS SEE PAGE 2 14562 Pg 00-00 12/2/00 12:36 PM Page 1 Designing Our Products
More informationRMR Free-Standing Enclosures
Protecting your technology investment. RMR Free-Standing Enclosures provide NEMA Type 4 and 12 protection for large electronic components and controls that require sturdy mounting. ADVANTAGES Advanced
More informationELECTRICAL ACCESSORIES FOR 1 5 8" (41 MM) WIDTH SERIES CHANNEL
ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL Page Electrical Fittings Receptacles Fixture Hangers ccessories and Connectors Junction Boxes In-Channel Joiners Swivel Hangers Cable Entrance Tubing
More informationStandard Product Low Profile Type 12 One-Door Disconnect Enclosures
763.422.2600 Spec-00005 M763.422.2211 Wall-Mount Preferred-Cutout s Low-Profile Type 12 s and Accessories Wall-Mount Preferred-Cutout s Low-Profile Type 12 s and Accessories Low-Profile, One- to Five-Door
More informationWedge Consoles Joining Kit Full Back Panel Side-Mount Panel Caster Kit Bulletin: P11. E mm/in
Spec-01204 OLI old Series esk Consoles esk Consoles and Accessories old Series esk Console, Type 12 ALICATIO The OLI old Series esk Console provides an ideal surface for mounting MI controls such as keyboards,
More informationSc h rader Bellows. CS Series Air Control Valves. 2 & 3-Way, Inline, Manifold & Stacking Direct Acting Solenoid Valves
Sc h rader Bellows 2 & 3-Way, Inline, Manifold & Stacking Direct cting Solenoid Valves INDEX PGE Features Inline Valves... 3 Stacking Valves... 4 Manifold Valves... 5 Valve Model Number System... 6 Solenoid
More informationStandards IEC IEC 529 Rated IP66-9 EN EN Mounting frame: removable predrilled reinforced DIN-rails
Features - The range is available in seven sizes, ranging from 12" x 8" to 40" x 32". - The cabinets are made of beige (RL 7032) hot molded fiberglass reinforced polyester, dyed in mass. The enclosure
More information[ SOLUTIONS FOR AUTOMATION & CONTROL DEVICES: ]
[ SOLUTIONS FOR AUTOMATION & ONTROL DEVIES: ] INDUSTRY STANDARDS Solid hinged cover models. Mounting brackets required to meet UL/SA external mounting requirements. FEATURES remove and -install hinge pins
More informationMATERIAL SPECIFICATION ELECTRIC OPERATIONS ORGANIZATION. M3902 ****Supercedes BECo Standard E and ComElectric Spec ****
Page 1 of 8 ****Supercedes BECo Standard E2.12-2.12 and ComElectric Spec 6-0895**** 1.0 General Requirements SINGLE PHASE PAD-MOUNTED DISTRIBUTION TRANSFORMERS 1.1 These specifications cover single-phase
More informationCONCEPT Accessories. Catalog Number Material Fits CONCEPT Enclosure CCPM4 Steel When A x B is equal to or less than x in.
Spec-00186 KPH FX (763) 422-2600 422-2211 Accessories CONCEPT Accessories Accessories: CONCEPT Conversion Kit Conversion Kit adapts enclosure for mounting standard NEMAstyle panels in CONCEPT enclosures.
More informationSTAINLESS STEEL ENCLOSURES
Electromechanical components STINLESS STEEL ENCLOSURES GL66 SERIES [ REEFINING STNR ] GL66 LL-MOUNT ENCLOSURES: INGE COVER [ GL66 SERIES STINLESS STEEL ] INGE COVER LL-MOUNT ENCLOSURES Manufactured in
More informationC-Box Screw Cover with Knockouts NEMA 1. Commercial Enclosures Junction Boxes
C-Box Screw Cover with Knockouts Application Designed for general purpose indoor commercial use as a junction, pull or switch box. Standards UL-50 Type 1 cul Type 1 Complies with: NEMA Type 1 IEC 60529,
More informationFull Subpanel. Additional Mounting Hardware
Spec-00431 PROLINE Internal Components Panel and Grid Mounting System Full Subpanel PROLINE subpanels are designed to provide maximum panel depth, panel size and ease of installation. Full subpanels slide
More informationSquare-Duct Wireways. Catalog 5100CT0101R06/ Class CONTENTS Description... Page. Wireway Offerings... 3
Catalog 5100CT0101R06/11 2011 Class 5100 CONTENTS Description............................................. Page Wireway Offerings............................................ 3 General Purpose NEMA Type
More information1E EJB Junction Boxes Cl. I, Div. 1 and 2, Groups B, C, D
Cl. I, Div. and 2, Groups B, C, D Cl. II, Div., Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 3, 4, 4*,, Ex d IIB + H2 T, IP Explosionproof Dust-Ignitionproof Raintight Wet Locations Applications:
More informationRMR Floor-Mount Enclosures
Protecting your technology investment. RMR Floor-Mount Enclosures provide NEMA Type 4 and 12 protection for large electronic components and controls that require sturdy mounting. Floor stands elevate the
More informationGuides. Slides. Mounting Accessories Rack-Mount Accessories
Spec-00500 Mounting Accessories Rack-Mount Accessories Guides 14 gauge steel chassis guides mount between two pairs of rackmounting angles that have accessory mounting legs. Guides and mounting hardware
More information*Discover our other ranges: Select your range of Spacial steel wall-mounting enclosures. Spacial S3DC. Spacial S3X page 5/4. Thalassa PLM page 6/12.
Spacial SDC Select your range of Spacial steel wall-mounting enclosures SDC You need an efficient, sealed multipurpose and aesthetic enclosure for an indoor industrial facility. Our solution: the Spacial
More informationIndustrial Enclosures
48J Series - NEMA 2 Large JIC Enclosures Junction Boxes Application Designed to house electrical, electronic, hydraulic or pneumatic controls and instruments. Provides a degree of protection from falling
More informationPhone: Fax: Web: -
empire SERIES For your largest applications, turn to the Empire Series from Allied Moulded. Fiberglass construction offers durability and strength without the excessive weight of a comparable metal enclosure.
More informationSurface Applied Door Closers DORMA TS93
Surface Applied Door Closers DORMA TS93 DORMA TS93 Surface Applied Door Closers The TS93 System in Contur Design represents the pinnacle of surface applied closers because of its unique cam and roller
More informationLUM SERIES-PLED w/ POLE RATED FOR 100MPH SHAFT
EXPEDITED AVAILABILITY LUM SERIES-PLED w/ POLE RATED FOR 100MPH SHAFT PROJECT NAME: FIXTURE TYPE: FIXTURE HOUSING Heavy cast low copper aluminum assembly (A360 alloy,
More informationSeries 2, 3, 4, & 5 Aluminum - Accessories
The following is a list of accessories and fittings that can be provided with S8 tray. For more information on these items, contact our Engineering Department. Fittings Horizontal Bends 30 Bends with 24,
More informationProduct Data For FARNELL
ae Product Data For FARNELL ae Uniset is / Varioset is ae EL ELECTRONIC KOMBI SYSTEM WALL MOUNTING Pole clamp For reliable, convenient fastening to round or square poles. For pole diameter/size:
More informationF LANGE MOUNT DISCONNECT
F LNGE MOUNT DISCONNECT E Wallmount FMD s... FMD 1-2 NEM 4 Wallmount Boxes... FMD 3-4 NEM 12 Wallmount Boxes... FMD 5-6 TS8 Freestanding FMD s... FMD 7-8 PS Freestanding FMD s... FMD 9-10 Freestanding
More informationOverall Dimensions. Specifications
Overall Dimensions EFX B EFX VM Vertical Mount C 13 housing (70-400W) 19 housing (450-1000W) E D H B C D E 13.3 16.8 16.2 7.0 9.8 (33.78cm) (42.67cm) (41.15cm) (17.78cm) (24.89cm) F G H I J 22.2 11.3 6.3
More informationSPECIAL SPECIFICATION 8676 Solar Panel Power Supply System
2004 Specifications CSJ 2552-01-033 SPECIAL SPECIFICATION 8676 Solar Panel Power Supply System 1. Description. This work shall consist of furnishing and installing an integrated Solar Panel Power Supply
More informationTERMINATION ENCLOSURE OPTIONS
TERMINATION ENCLOSURE OPTIONS Add suffix: R - Reverse Stagger the Bus Bars (to run cable in from the top) CU - Copper NEMA Mount Bus Bars C - Plastisol Covers for Bus Bars DF - Dead Fronts T - Tin Plated
More informationGuides (s-3482) Slides (s-2568) Rack-Mount Accessories. Accessories: Mounting Accessories
Spec-00500 D(763) 422-2211 422-2600 Accessories Mounting Accessories Guides (s-3482) 14 gauge steel chassis guides mount between two pairs of rackmounting angles that have accessory mounting legs. Guides
More informationPanel, 18.20x14.20, Bulletin CWP (CONCEPT Enclosure Panels),
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 Catalog Number Manufacturer Description Weight per unit Product Category Features Material Material, Color, and Finish
More informationRigid/Aluminum Conduit Bodies, Gaskets and Covers
Rigid/luminum Conduit odies, Gaskets and Covers Conduit odies, Covers and Gaskets Weatherproof oxes and Covers pplications Junction for branch conduits Series bodies for Rigid and IMC conduit maintain
More informationPolycarbonate Watertight 03 Product Drawings Last Updated 6/18/2008
ROSE+BOPL PHOENIX MECNO COMPNY Polycarbonate Watertight 03 Product Drawings Last Updated 6/18/2008 Rose+Bopla Enclosures 7330 Executive Way Frederick, MD 21704 301-696-9800 www.rose-bopla.com rbinfo@pm-usa.com
More information1E EJB Junction Boxes Cl. I, Div. 1 and 2, Groups B, C, D
EJB Junction Boxes Cl. I, Div. and 2, Groups B, C, D Cl. II, Div., Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 3, 4, 4X*,, Ex d IIB + H2 T6, IP66 Explosionproof Dust-Ignitionproof Raintight
More informationTRAY AND RACK DISPENSER. Model Series: TRC-M-* APPLICATION: -Cafeterias -Serving lines -Tray make-up systems -Back up storage -Modular buffet systems
TRAY AND RACK DISPENSER - CANTILEVER DESIGN - SINGLE OR DOUBLE - SELF LEVELING, FIELD ADJUSTABLE Model Series: TRC-M-* APPLICATION: -Cafeterias -Serving lines -Tray make-up systems -Back up storage -Modular
More informationModular Enclosure Solutions Specifier s Guide
Modular Enclosure Solutions Specifier s Guide EQUIPMENT PROTECTION WWW.PENTAIRPROTECT.COM/HOFFMAN Volume 1 The Next Generation Modular Enclosure Stronger. Faster. Easier. You ve already spent tens of thousands
More informationA. Three-phase, oil filled self-cooled, padmounted transformers are installed outdoors on pads in the EWEB distribution system.
1. APPLICATION A. Three-phase, oil filled self-cooled, padmounted transformers are installed outdoors on pads in the EWEB distribution system. 2. REFERENCE STANDARDS A. The transformers supplied shall
More informationPreferred Cutout, Disconnect Enclosure, Type 12
763.422.2600 Spec-00245 J763.422.2211 Wall-Mount Preferred-Cutout s Preferred Cutout, s, Type 12 Wall-Mount Preferred-Cutout s Preferred Cutout, s, Type 12 Preferred Cutout, Enclosure, Type 12 INDUSTRY
More informationSECTION 18 ENCLOSURES
COLTERLEC ELECTRICAL ENGINEERING PRODUCTS SECTION ENCLOSURES COLTERLEC ELECTRICAL ENGINEERING PRODUCTS 549 TM CONTENTS PHOENIX ENGINEERING & MANUFACTURING SOLUTIONS Stainless Steel Stainless Steel Wall
More informationStandard Product. Polyester powder paint; RAL 7035 textured light gray standard Custom colors available
Spec-01193 PROLINE G2 External Components Tops Solid Top 16 gauge (1.5 ) steel Additional support provisions need to be made to support top mount air conditioners or other top mount accessories Includes
More informationGland Plate 1.4mm mild steel. -Opening: Situated at the far rear of the enclosure to make cabling onto the mounting plate easier.
14 SM SHEET STEEL ENCLOSURES ITH MOUNTING PLATE FOR ALL MOUNTING SM Delivery contents: Complete enclosure with mounting plate and fixing material, Blank flange with gasket and screws. Nylon washers for
More informationRipac Vario-Module 2U
Ripac Vario-Module U IE 60 97- for installation in 48.6 mm (9 ) racks. to IE 60 97-3-0. Material/Surface finish: spray-finished in RL 7035 orner trims: spray-finished in RL 7035 Side trims: spray-finished
More informationRack Mount devices shown not included Custom cabinet shown
763.422.2588 SPEC-00215 M763.422.2661 NETWORKING OUTSIDE PLANT PRODUCTS COMLINE OSP WALL-MOUNT CABINET PACKAGE AND ACCESSORIES Outside Plant Products COMLINE OSP Wall-Mount Cabinet Package and Accessories
More informationIndustrial Enclosures
www Eclipse Junior Series Single Door Enclosures - NEMA 12, 13, 4... 2 Series 2000, Single Door Enclosures - NEMA 12, 4... 40 1414 Series JIC Enclosures, Clamped, Lift Off Cover - NEMA 12, 13... 4 1414
More informationEN4DSC Disconnect Enclosures - NEMA 4 ABB Controls, Allen Bradley, Cutler Hammer, General Electric, Siemens I-T-E Max-Flex, Square D
EN4DSC Disconnect Enclosures - NEMA 4 Application Designed to house the following safety disconnect equipment: ABB Controls flange mounted variable depth operating mechanisms for disconnect switches and
More informationIndustrial Enclosures
1414 Series JIC Enclosures - NEMA 12, 13 Clamped, Lift Off Cover Application Designed for use as instrument enclosures, electric, hydraulic or pneumatic control housings, electrical junction boxes or terminal
More informationCS COMPACT ENCLOSURE. CABINETS. method for lifting uses the same eyebolts as ATB8 cabinets. optional 180 hinges available
CS COMPACT ENCLOSURE method for lifting uses the same eyebolts as ATB8 cabinets optional 180 hinges available CS enclosures can be wall-mounted using standard SDWC-010 mounting brackets as used on ST Box
More information