Trough, Wireway & Strut Attributes

Transcription

1 Trough, Wireway & Strut Trough, Wireway & Strut Stahlin offers a broad range of auxiliary products designed to complement a full non metallic wiring system. Wire management through a corrosion resistant system requires a thoroughfare of chemically resistant and environmentally protective materials. Fiberglass wireway is designed to protect point to point wiring in highly corrosive environments such as plating rooms, solder bath areas, rendering & cutting areas and chemical processing. By its description, wireway is sold in multiple lengths and is joined with other lengths of wireway through a series of fittings designed to cover an expanse. The system is not rated for the ingress of moisture but is suitable for both indoor and outdoor use. Pultruded fiberglass trough is identical to wireway except that it is made to a defined length. As a result, the product consists of six specific lengths and has sealed end caps to close off each end. Trough products Wireway Featured Highlights include a polyurethane gasket in a snap cover that attaches gh & u o without screws. It is designed to accommodate some metal Tr trough accessories and can be custom supplied with mounting feet. Snap On Cover An additional form of pultruded fiberglass is used without Screws for strut, a common mounting and support system for both trough, wireway and enclosures. Stahlin strut is available with hanger rod, washers & nuts, Polyurethane beam clamps, strut cover, strut buckles and end Gasket sealant. It is sold in ten foot lengths. Trough, Wireway & Strut Attributes Pultruded fiberglass products Polyurethane gasket Available with mounting feet Complete line of accessory fittings available for wireway High temperature, non corrosive, environmental designs Physical Protection Environmental Protection Add On Mounting Feet Trough, Wireway & Strut Specifications Corrosion Resistant Fire resistant Rigid Mechanical protection Trough, Wireway & Strut are Applicable for Many Industries including: Circuit Board Development Plating Industry Rendering Plants Water & Wastewater Processing

2 Trough & Wireway 6" x 6" trough & wireway Available in six common lengths Snap lock cover without screws Polyurethane gasket Add on mounting feet

3 Fiberglass Wireway WW WW Fiberglass Wireway Fiberglass wireway is the perfect complement to wall mount control systems as an environmentally sound wiring pathway with both strength characteristics and corrosion resistance. Stahlin fiberglass wireway is well suited as a protective pathway between non metallic enclosures in applications such as greenhouses, livestock installations, plating rooms and printed circuit board manufacturing. The product features a six by six size in a variety of lengths with a full complement of fittings for typical plant installations. WW6636 Fiberglass Wireway Dimensions SIZE ID NUMBER INSIDE DIMENSIONS H X W X D OUTSIDE DIMENSIONS H X W X D DESCRIPTION WW x 6 x /8 x 6-11/16 x 12-3/8 12" straight section (152 x 152 x 305) (162 x 170 x 314) WW x 6 x /8 x 6-11/16 x 24-3/8 24" straight section (152 x 152 x 610) (162 x 170 x 619) WW x 6 x /8 x 6-11/16 x 36-3/8 36" straight section (152 x 152 x 914) (162 x 170 x 924) WW x 6 x /8 x 6-11/16 x 48-3/8 48" straight section (152 x 152 x 1219) (162 x 170 x 1229) WW x 6 x /8 x 6-11/16 x 60-3/8 60" straight section (152 x 152 x 1524) (162 x 170 x 1534) WW x 6 x /8 x 6-11/16 x 120-3/8 120" straight section (152 x 152 x 3048) (162 x 170 x 3058) All measures are in inches, items in parentheses are in millimeters. H6645 V6645I H66T V6645O PA66 H66T V6645O C66 V6690O V6645I H669I V6690I EP66 EP66 311

4 Fiberglass Wireway continued on following pages Fiberglass Wireway Fittings CATALOG NUMBER DESCRIPTION C66 Coupling with gasket cover and fasteners H66T Tee with gasketed cover H6645 Horizontal 45º elbow H669I Horizontal 90º elbow V6690I Inside vertical 90º elbow V6690O Outside vertical 90º elbow V6645I Inside vertical 45º elbow V6645O Outside vertical 45º elbow EP66 End plate PA66 Panel adapter Wireway Assembly Materials CATALOG NUMBER DESCRIPTION RTV32 clear RTV silicone 3 oz. tube SS625 stainless steel screws #10-24 x 5/8" Long SN104 stainless steel nut #10-24 WIREWAY INSTALLATION It is recommended that Stahlin wireway be supported at intervals not exceeding 10 feet. Vertical runs should be supported at intervals not exceeding 15 feet with no more than one joint between supports. Joining wireway straight sections is accomplished by placing a coupling (C66) over the outside diameter of the wireway. The coupling is predrilled to accept a stainless steel screw. The 7/32" diameter holes in the side of the coupling can be used as a template to field drill the end of the wireway. Wireway fittings can be joined to straight sections in the same manner as joining straight sections. To provide a seal, run a bead of RTV silicone or equivalent around each coupling (outboard of the fasteners) before assembly. End plates are force fit and can be installed as needed and sealed with RTV silicone. C66 H66T H6690 V6690I V6690O V6645I V6645O EP66 312

5 Fiberglass Trough & Strut FT FT Fiberglass Trough Fiberglass trough is a useful complement to wall mount control systems with the same strength characteristics and corrosion resistance as Stahlin wireway. Made from the same fiberglass pultrusion, trough features permanent end caps as well as a snap lock cover that forms a solid housing. FT6612 Trough is offered as simple protection to wiring from water, oil, dust or corrosive environments, including greenhouses, food processing, plating rooms, pickling and printed circuit board manufacturing. The basic offering includes a six by six structure that is available in six common lengths. Fiberglass Trough Dimensions SIZE ID NUMBER INSIDE DIMENSIONS H X W X D OUTSIDE DIMENSIONS H X W X D UNIT WEIGHT FT x 6 x /8 x 6-5/8 x 12-3/ lbs. (152 x 152 x 305) (162 x 168 x 314) FT x 6 x /8 x 6-5/8 x 24-3/ lbs. (152 x 152 x 610) (162 x 168 x 619) FT x 6 x /8 x 6-5/8 x 36-3/ lbs. (152 x 152 x 914) (162 x 168 x 924) FT x 6 x /8 x 6-5/8 x 48-3/ lbs. (152 x 152 x 1219) (162 x 168 x 1229) FT x 6 x /8 x 6-5/8 x 60-3/ lbs. (152 x 152 x 1524) (162 x 168 x 1534) FT x 6 x /8 x 6-5/8 x 120-3/ lbs. (152 x 152 x 3048) (162 x 168 x 3058) All measures are in inches, items in parentheses are in millimeters. 4" 3" 2" 1" PVC Coated Pipe Straps PART NUMBER SIZE PBC105-1/2 1/2" PBC105-3/4 3/4" PBC " PBC105-11/4 1-1/4" PBC105-11/2 1-1/2" PBC " PBC105-21/2 2-1/2" PBC " PBC105-31/2 3-1/2" PBC " PBC " PVC Coated Pipe Straps 313

6 Fiberglass Trough & Strut Fiberglass Strut Fiberglass strut is the finishing complement to both wireway and trough. Used for both mounting purposes and support, this rigid pultruded fiberglass mounting system is designed around three configurations, low profile, medium profile and double profile. A full assortment of accessories from beam clamps to strut cover is available. This rigid support system in completely corrosion resistant. 20P2100 FIBERGLASS STRUT Strut SIZE ID SIZE HOLE WEIGHT NUMBER (INCHES) DIMENSION/TAPPING PER 100' STRUT 20P ' length N/A P ' length N/A P ' length N/A 52.0 Non-Metallic Hanger Rod (All Thread) 3.25 [82.55mm] 1.63 [41.28mm] 1.25 [31.75mm] [38.89mm] / " N/A /8-13/ 96" N/A 18.0 Non-Metallic Hanger Rod Washers [19.05mm] 500E-999 1' diameter 1/2" N/A 1/16" thickness 625E-999 1/12" diameter 5/8" N/A 1/16" diameter Non-Metallic Hanger Rod Nut 20P [41.28mm] 1.25 [31.75mm] 500PU-000 1/2-13 hex N/A N/A 625PU-000 5/8-13 hex N/A N/A Non-Metallic Strut Cover 20E-5000 snap in N/A N/A Non-Metallic Strut Nut 500PU-CNH-D 1/2-13 N/A N/A 1.63 [41.28mm].75 [19.05mm] PVC Coated Beam Clamp RGBC2 1" jaw opening 1/2-13 N/A RGCB3 1" jaw opening 5/8-13 N/A End Sealant.125 [3.18mm].125 [3.18mm] 20P [38.10mm] 1.25 [31.75mm] oz. spray can N/A N/A 1.13 [28.58mm] AES1 quart can N/A N/A.375 [9.52mm].75 [19.05mm].375 [9.52mm] 314