CFW700 Variable Speed Drives. Motors Automation Energy Transmission & Distribution Coatings

Transcription

1 CFW700 Variable Speed Drives Motors utomation Enery Transmission & Distribution Coatins

2 CFW-700 Desined for controllin squirrel cae three-phase induction motors the new CFW700 is a eneral purpose drive that ives costumers the flexibility needed for the control of applications ranin from simple speed control to more demandin ones as torque control. Since it is included on its control the CFW700 features Sensor less and Closed loop control as standard feature (factory built). nother outstandin characteristic we could not leave behind is that by usin the internal micro PLC (SoftPLC factory built), more sophisticated applications like overhead cranes, PCP (Proressive Cavity Pump), pump jack and many more can be implemented. Technoloy Vectrue Technoloy - WEG VRIBLE SPEED DRIVE CONTROL TECHNOLOGY Four control modes in one drive, Linear and adjustable V/f, VVW (Voltae Vector WEG), Sensorless Vector and closed loop Vector. ( Encoder interface factory built) Sensorless vector control allows for hih torque and quick response in open loop, even at low speeds. Self-tunin function automatically matches VSD with motor load when on Sensorless, VVW and closed loop Vector mode. Throuh adjustable V/f control it is possible to adjust a quadratic V/f curve and that implies enery savin when quadratic torque loads (e..: centrifual pumps and fans) are bein driven. Optimal Brakin WEG FREQUENCY INVERTERS BRKING TECHNOLOGY In applications where hih inertia and short deceleration times are involved, a lare amount of enery is returned from the motor to the VSD. To handle this enery traditional VSDs have to dissipate it as heat in power resistors, such resistors are usually lare and very expensive also some installation criteria has to be considered due to their heat dissipation. s an alternative to the use of brakin resistors the CFW700 features a special brakin method in vector control mode named Optimal Brakin. This innovation delivers rated torque with hih performance requirin no resistor. The raph iven below shows a comparison of the brakin torque offered by the different brakin methods used. 100 (%) TB1 Brakin Torque (%) % 100% 200% Typical Brakin Torque x Speed Graph for a 10 HP / 7.5 kw motor driven by a CFW700 Dynamic Brakin Torque Curve Optimal Brakin Torque Curve DC Brakin Torque Curve Optimal Flux WEG TECHNOLOGY FOR THE CONTROL OF HIGH EFFICIENCY INDUCTION MOTORS PPLIED TO CONSTNT TORQUE LOD Rated torque at very low speed discardin the use for forced ventilation or even motor oversizin, thus costs are reduced. Better performance results can be achieved with the set motor + VSD, as losses are decreased (tests were conducted based on the set WEG hih efficiency MOTOR + WEG VSD). 2 Frequency Inverter Series - CFW700

3 Keypad The CFW700 comes equipped with a LCD display capable of providin readins for prorammin, uided start-up and troubleshootin. This customized numeric LCD display features the followin functionalities: LCD display with back liht llows adjust prorammin throuh menu separate in folders Remote mountin for panel assembly solutions ( it can be placed 30m distant from the drive) Left soft-key: function defined by display Key for scrollin throuh menus and perameters and for modfyin perameter content FWD/REV Selection Star Key Local / Remote Selection Stop Key JOG Key Remote Keypad The Keypad can be remote assembled by usin this confiuration, deree of protection IP56 can be achieved. Frequency Inverter Series - CFW700 3

4 llows for showin 3 variables at once throuh three viewin modes Inverter Status Menu (parameters roup selection) only one parameters roup is shown each time. uxiliar Display Units of Measurement (refers to the main display value) Variable Monitorin Bar Main Display Viewin Modes Monitorin Mode Prorammin Mode 4 Frequency Inverter Series - CFW700

5 Simplicity The new CFW700 was desined based on the plu and play technoloy concept where by pluin in expansion modules hardware and software reconize it automatically. lso this feature allows for easy installation and safe operation with no need for additional confiuration. Slot 3 Communication Module ( optional) Slot 5 Flash Module ( optional) Frequency Inverter Series - CFW700 5

6 Technical Features Main parts Frames, B and C Rear part of the inverter (external part for flane mountin) Flash memory module (not included) Mountin supports (for throuh the wall mountin) Control accessory module Front cover Fan with mountin support CC700 control board Keypad Status LED 6 Frequency Inverter Series - CFW700

7 Technical Features Main parts Frames D and E Flash memory module (not included) CC700 control board Control accessory module Mountin supports (for throuh the wall mountin) Status LED Keypad Control rack cover Rear part of the inverter (external part for plane mountin) Holstin eye (only on frame E) Bottom front cover Fan with mountin support Frequency Inverter Series - CFW700 7

8 Technical Features 1.1 to 2.2kW to 3HP V - Sinle-phase 1.1 to 55kW to 75HP V - Three-phase 1.5 to 132kW - 2 to 175HP V - Three-phase Very compact product ives flexibility for lack of space when panel mounted Hih accuracy and reliability for speed and torque control Hardware robustness Control Terminal White +V Linedrive encoder or push-pull Blue Red Green B Yellow B V ctive hih diital inputs REF+ l1+ l1- REF- O1 GND (24V) O2 GND (24V) +24V COM GND(24V) DI1 DI2 DI3 DI4 5 kω rpm rpm I2+ L2- RL1-NF RL1-C RL1-N +5V-ENC GND-ENC - RS485 B - RS485 >300 Ω >300 Ω >300 Ω >300 Ω DO2 DO3 DO4 DO5 B GND(24V) DI5 DI6 DI7 DI8 Z Z Z GND Pink Grey Brown ++ + B Z 8 Frequency Inverter Series - CFW700

9 Technical Features = DC busbar connection 2 = Connection for brakin resistor DC+ BR DC- Filtro C3 (*) (available for models CFW700...C3...) POWER Power network R/L1/L S/L2/N T/L3 Prechare U/T1 V/T2 W/T3 PE Three-phase rectifier DC link chokes DC link capacitor Bank Brakin IGBT (available in CFW700...DB...inverters) RFI Filter Inverter with IGBT transistors Motor Feedbacks: - Voltaes - Current PE PC CONTROL RS485 Power Supplies for electronics and interfaces between power and control. Software Superdrive G2 Software WLP MMI 3 (remote) HMI 3 ccessories COMM 1 (Slot 3 Green) Diital Inputs ( DI1 to DI8) nalo Inputs (I1 and I2) CC700 Control Card with 32-bit RISC CPU (Slot 4 nybus) nalo Outputs (O1 and O2) Diital Outputs DO1 (RL1) FLSH Memory Module (Slot 5) Diital Outputs DO2 to DO5 3 = Keypad (*) The capacitor to the round of the C3 filter must be disconnected for IT networks Notes: 1)Diode type rectifier bride 2) Standard for frame sizes to D 3)RFI filter factory built for frame size E Frequency Inverter Series - CFW700 9

10 Technical Features Interated options for the product Built-in DC link Reactor llows the VSD to be installed in any network (No restriction for Power supply impedance) Typical Power factor (PF) for steady condition: 0.94 for Three-phase models 0.70 for Sinle-phase and Sinle/Three-phase models fed from Sinle-phase Power supply Displacement Power factor > 0.98 It meets standard (Limits for Harmonic currents) No need for an extra line reactor Encoder Interface For applications requirin closed loop control the encoder module is available at the control terminals. No need for external power supply for the encoder module( 5Vcc) 5V Line drive or push pull types can be used RS-485 port Embedded Modbus-RTU communication protocol ready I/Os capability 8 Diital Inputs / 5 Diital Outputs 2 nalo Inputs / 2 nalo Outputs Common Dc bus Connection Very known in multi motors application the possibility for feedin CFW700 (C drive) with DC voltae ives flexibility to the product as well as brins the benefit for enery savins. By sharin a common DC bus in some applications the enery consumption can be lowered as the power needed to run any of the motors can be drawn from the stored enery at the VSD DC link. Supply Network General Input Rectifier Unit CFW700 Sinle DC Link n Note: n external pre-chare circuit must be added to each of the VSDs. Thermal Manaement The possibility for monitorin heat sink and inside air temperature ensures protection to critical components e.. IGBTs and control board. Fans installed closed to heatsink are turned on and off dependin on the temperature of power modules. Readins of fan operation hours can be analyzed throuh parameters as well as alarm or fault messaes are displayed. Easy removal of fans makes maintenance and or replacement a lot faster. 10 Frequency Inverter Series - CFW700

11 Technical Features Drive Features Multi-speed: Up to 8 preset speeds can be prorammed PID reulation: Eliminates the use of an external controller for closed loop control, thus reat performance of speed and torque can be achieved. Ride Throuh: Embedded in the CFW700 control this function avoids the drive from trippin durin some power outae. It uses the kinetic enery stored throuh a forced deceleration imposed to the load by the VSD control alorithm. Speed/Torque reulation: Open and closed loop (encoder feedback required). Flyin start: It is able to start smoothly a motor connected to a rotatin load reardless rotation direction. Control options for DC bus reulation Prevents the drive from trippin when short deceleration time is required, very demanded for applications with hih inertia loads. S ramp: The smoothness at the Startin can be mandatory for process e.. the beverae industry, by settin up properly this functionality production losses caused by traditional startin methods can be avoided. Three-wire Start/Stop control: No retentive contact can command the drive to start/stop the motor. Electronic Potentiometer: The drive keeps increasin motor speed as lon as the diital input remains closed. Skip Frequency: For some applications specific frequencies must be avoided in order to protect the machine aainst resonance effect. Motor thermal curve adjustment: The possibility for separate adjustment between motor and drive allows for a much more effective protection for overload cycles. Copy function: By usin the flash memory card MMF-02 parameter settins can be easily stored ensurin interity and safety in case of replacement of the drive is needed. Frequency Inverter Series - CFW700 11

12 Soft PLC The new CFW700 incorporates PLC functionalities by means of a factory built micro PLC named Soft PLC. This extra tool ives more flexibility to the product as well as allows the user for developin his own application throuh a RS-485 port available at the control terminal. The Soft PLC features the followin characteristics: ccess to CFW700 I/Os and parameters PLC mathematics and Control Blocks llows user password User can save software in the memory flash card to be downloaded into other VSDs. Free of chare Software WLP (WEG ladder prorammer) Software Desined for development of user application throuh the micro PLC embedded in the CFW700 hardware. The WLP tool features the followin capabilities: Ladder prorammin PLC, math and control blocks are available ccess to all CFW700 parameters On-line monitorin as well as help topics RS-485 connection with the drive 49 user parameters can be individually accessed allowin for creation of a variety of applications. Software superdrive G2 It is a windows-based Software desined for the prorammin, commandin and monitorin of WEG VSDs. The followin features the user can benefit from: utomatic CFW700 reconition CFW700 parameters monitorin Off-line/On-line chane of parameters Reports can be created Backup of parameters Start/Stop command as well as speed reference can be sent to the drive. 12 Frequency Inverter Series - CFW700

13 ccessories Blank cover HMID Used when there is no need for keypad Remote keypad frame RHMIF-02 Used when remote keypad is needed, it can be installed at the panel door as well as machine console. IP 56 deree of protection. Communication Modules CN-01 ( CNopen and DeviceNet) Profibus DP-01 ( Profibus DP-V1) Flash Memory module MMF - 02 This module allows for backup of VSD parameters ensurin the prorammin to be safely stored. lso it makes possible the prorammin to be passed on to other VSDs on the same plant avoidin repetitive prorammin. The Soft PLC applicative can also be store into this memory. 1 These options must be provided already installed in the CFW700 (please see codin on pae 21). Frequency Inverter Series - CFW700 13

14 ccessories Kit for Shielded Cable PCS-01 PCSB-01 PCSC-01 Shielded cable Kit frame size Shielded cable Kit frame size B Shielded cable Kit frame size C Note: 1) The shielded cable kit for frame Sizes D and E is included to the standard version. 2) For models with RFI filter fitted in shielded cable kit comes as standard. Enclosures Standards IEC ( X ) Standard ( - ) N Ratins Frame Sizes B C D E IP20 X X x X X IP21 KIP21-01 KIP21B-01 KIP21C-01 KIP21D-01 - NEM TYPE 1 KN1-02 KN1B-02 KN1C-02 X KN1E-01 / KN1E-02 Standard ccessory Composition NEM Type 1 IEC KN1-02 Conduit kit frame size KN1B-02 Conduit kit frame size B KN1C-02 Conduit kit frame size C KN1E-01 Top cover size E models 105 and 142 KN1E-02 Top Cover + Conduit kit size E models 180 and 211 KIP21-01 Top cover kit frame size KIP21B-01 Top cover kit frame size B KIP21C-01 Top cover kit frame size C KIP21D-01 Top cover kit frame size D Note: In the KN1X-01 Conduit kit (frame sizes,b and C) power cable shieldin is also provided 14 Frequency Inverter Series - CFW700

15 Optionals (factory built) External control power supply 24Vcc Used mainly for communication networks allowin data exchane even when there is no power at the VSD input.(this module must be fed from a power supply different from the one connected to the VSD). RFI suppressor filter( for the VSD to be in accordance with EN and EN 55011) When properly installed the CFW700 meet requirements of the electromanetic compatibility directive EMC Directive 2004/108/EC. For models ranin from size to D, the RFI filter is optional and for size E it is included. Safety Stop (in accordance with EN and IEC 62061, cateory III) With this option when the safety circuit is tripped by external causes the IGBT firin circuit is deactivated, thus removin power from VSD output. ( pendin certification). Frequency Inverter Series - CFW700 15

16 pplications Pumps and fans Precise control of process variables (pressure, flow, temperature, etc.) throuh a PID reulator superposed to the speed control. Optimization of power consumption throuh speed control with an adjustable V/f curve. Possibility of safety and maintenance sinalin and alarms of pumps and fans. vailability of PID reulators to control other process accessories like valves, dumpers, other VSDs, etc. Compressors Optimization of system pressurization control with enery savins and improvement of compressor efficiency. Reduction of motor startup current minimizin wear and tear of the mechanical system avoidin fees chared by the power supplier company. Possibility of safety and maintenance sinalin and alarms of pressurization system. Provides startup system control of other compressor units with an increased efficiency of the pressurization system. Paper and Cellulose / Wood Precise speed and torque control. Flexible hardware prorammin and confuration, makin applications where syncronism is required easier. Possibility to be interatet in a variety of communication protocols commonly used in the industry. Provided in a compact desin the CFW700 series allows for side by side assembly. Quick and simplified prorammin. Hihly reliable and robust. Chemical and Petrochemical Hihly reliable and robust. Plu-and-play system for additional modules, ensurin reater flexibility in adaptin to existin systems. Possibility to be interated in a variety of communication protocols commonly used in the industry. Ironworks and Metallury Hihly precise speed and torque control. Lare overload capacity (models sized in HD). Flexible hardware prorammin and confiuration. Possibility to be interated in a variety of communication protocols mainly used in the industry. 16 Frequency Inverter Series - CFW700

17 Drive Ratins Normal Duty (ND) Cycle: 110% for 60 seconds every 10 minutes 150% for 3 seconds every 10 minutes Heavy Duty (HD) Cycle: 150% for 60 seconds every 10 minutes 200% for 3 seconds every 10 minutes Sizin a VFD: The proper way how to size a frequency inverter is by matchin its output current with the motor rated current. However, tables below present the expected motor power for each VSD model. The purpose of the table below is to be used for uidance as motor rated current may vary with number of poles and manufacturer. Note: Motor power stated on this table is based on IEC standard for IV poles motor. Motor Voltae 220V and 230V IEC NEM IEC NEM Normal Duty 50Hz Heavy Duty 50Hz (ND) 60Hz 220V (HD) 60Hz 220V Power 230V 230V Model 230V 230V Supply kw HP kw HP CFW70006POS CFW70007POS CFW70010POS CFW70006POB CFW70007POB CFW70007POT CFW70010POT CFW70013POT CFW70016POT CFW700B24POT CFW700B28POT CFW700B33POT CFW700C45POT CFW700C54POT CFW700C70POT CFW700D86POT CFW700D0105POT V V 1Ø 1/3Ø 3Ø 3Ø CFW700E0142POT CFW700E0180POT CFW700E0211POT Motor Voltae 380V and 460V V Power Supply 3Ø Normal Duty (ND) 50Hz 380V 415V IEC 60Hz 440V 460V NEM 60Hz 460V Heavy Duty (HD) Model kw HP HP kw HP HP CFW70003P6T CFW70005P0T CFW70007P0T CFW70010P0T CFW70013P5T CFW700B17P0T CFW700B24P0T CFW700B31P0T CFW700C38P0T CFW700C45P0T CFW700C58P5T CFW700D70P5T CFW700D88P0T CFW700E0105T CFW700E0142T CFW700E0180T CFW700E0211T Hz 380V 415V IEC 60Hz 440V 460V NEM 60Hz 460V Frequency Inverter Series - CFW700 17

18 Dimensions, Weiht and Temperature Model CFW70006POS2 Frame Size NEM 1 IP20 / IP21 IP20 NEM 1 / IP21 Dimensions mm (in) H W D H W D Maximum Surrondin ir Temperature with no deratin C ( F) _ ND/HD 50 (122)_ND/HD 50 (122)_ND/HD CFW70007POS2 50 (122)_ND/HD 45 (113)_ND/HD CFW70010POS2 50 (122)_ND/HD 50 (122)_ND/HD CFW70006POB2 50 (122)_ND/HD 50 (122)_ND/HD CFW70007POB (122)_ND/HD 45 (113)_ND/HD CFW70007POT2 (12.02) (5.71) (8.94) (9.73) (5.71) (8.94) 50 (122)_ND/HD 45 (113)_ND/HD CFW70010POT2 50 (122)_ND/HD 50 (122)_ND/HD CFW70013POT2 45 (113)_ND 50 (122)_HD 45 (113)_ND 50 (122)_HD CFW70016POT2 50 (122)_ND/HD 50 (122)_ND/HD CFW700B24POT2 45 (113)_ND/HD 40 (104)_ND/HD 351 CFW700B28POT (122)_ND/HD 50 (122)_ND/HD B (13.82) (7.46) (8.94) (11.53) (7.46) (8.94) 45 (113)_ND CFW700B33POT2 50 (122)_ND/HD 50 (122)_HD CFW700C45POT2 50 (122)_ND/HD 50 (122)_ND/HD CFW700C54POT2 C (17.64) (8.67) (11.52) (14.88) (8.67) (11.52) 50 (122)_ND/HD 50 (122)_ND/HD CFW700C70POT2 50 (122)_ND/HD 50 (122)_ND/HD CFW700D86POT (122)_ND/HD 50 (122)_ND/HD 32.6 D CFW700D0105POT2 (21.63) (11.81) (12.00) (19.84) (11.81) (12.00) 50 (122)_ND/HD 50 (122)_ND/HD (71.8) 735 CFW700E0142POT2 45 (113)_ND/HD 45 (113)_ND/HD (28.94) E CFW700E0180POT (13.2) (14.1) (24.4) (13.2) (14.1) 45 (113)_ND/HD 45 (113)_ND/HD CFW700E0211POT2 (32.63) 45 (113)_ND/HD 45 (113)_ND/HD CFW70003P6T4 50 (122)_ND/HD 50 (122)_ND/HD CFW70005P0T4 50 (122)_ND/HD 50 (122)_ND/HD 45 (113)_ND 40 (104)_ND CFW70007P0T (122)_HD 50 (122)_HD (12.02) (5.71) (8.94) (9.73) (5.71) (8.94) CFW70010P0T4 45 (113)_ND/HD 45 (113)_ND/HD Weiht k (lb) 6.3 (13.9) 10.4 (22.9) 20.5 (45.2) 650 (143.3) 6.3 (13.9) Brakin IGBT Standard Optional CFW70013P5T4 50 (122)_ND/HD 50 (122)_ND/HD CFW700B17P0T4 CFW700B24P0T4 B 351 (13.82) 190 (7.46) 227 (8.94) 293 (11.53) 190 (7.46) 227 (8.94) 50 (122)_ND/HD 50 (122)_ND/HD 50 (122)_ND/HD 40 (104)_ND 45 (122)_HD CFW700B31P0T4 50 (122)_ND/HD 50 (122)_ND/HD CFW700C38P0T4 50 (122)_ND/HD 50 (122)_ND/HD CFW700C45P0T4 C (17.64) (8.67) (11.52) (14.88) (8.67) (11.52) 50 (122)_ND/HD 50 (122)_ND/HD CFW700C58P5T4 50 (122)_ND/HD 50 (122)_ND/HD CFW700D70P5T (122)_ND/HD 50 (122)_ND/HD 32.6 D CFW700D88P0T4 (21.63) (11.81) (12.00) (19.84) (11.81) (12.00) 50 (122)_ND/HD 50 (122)_ND/HD (71.8) CFW700E0105T (113)_ND/HD 45 (113)_ND/HD CFW700E0142T4 ( 28.94) (113)_ND/HD 45 (113)_ND/HD E CFW700E0180T (13.2) (14.1) (24.4) (13.2) (14.1) 45 (113)_ND/HD 45 (113)_ND/HD CFW700E0211T4 ( 32.63) 45 (113)_ND/HD 45 (113)_ND/HD 10.4 (22.9) 20.5 (45.2) 650 (143.3) Standard Optional Note: Weiht data is for the VSD as IP20 enclosure, if IP21 and NEM1 kits are bein added the total weiht will chane. Consult the user manual for additional information. H w D 18 Frequency Inverter Series - CFW700

19 Mountin Considerations Innovative desin allows the CFW700 to be assembled in three different ways: Standard Installation D C B Frame Minimum Mountin Clearance with top Cover fitted in Size mm(in) B mm(in) C mm(in) D mm(in) 25(0.98) 25(0.98) 10(0.39) 30(1.18) B 40(1.57) 45(1.77) 10(0.39) 30(1.18) C 110(4.33) 130(5.12) 10(0.39) 30(1.18) D 110(4.33) 130(5.12) 10(0.39) 30(1.18) E 100(3.94) 250(9.84) 20(0.78) 80(3.15) Side by side Installation The possibility for installin CFW700 series with no space in between allows for panel space savin. Note: For side by side assembly option check user manual for further operatin temperature details. Frequency Inverter Series - CFW700 19

20 Mountin Considerations / Panel ssembly Surface Installation irflow Flane Mountin ( IP-54 rated when mountin the heatsink outside the enclosure) irflow Frame Size a2 mm(in) b2 mm(in) c2 (M) a3 mm(in) b3 mm(in) c3 (M) d3 mm(in) e3 mm(in) 115(4.53) 250(9.85) M5 130(5.12) 240(9.45) M5 135(5.32) 225(8.86) B 150(5.91) 300(11.82) M5 175(6.89) 285(11.23) M5 179(7.05) 271(10.65) C 150(5.91) 375(14.77) M6 195(7.68) 365(14.38) M6 205(8.08) 345(13.59) D 200(7.88) 525(20.67) M8 275(10.83) 517(20.36) M8 285(11.23) 485(19.10) E 200(7.8) 650(25.6) M8 275(10.8) 635(25) M8 315(12.40) 615(24.21) 20 Frequency Inverter Series - CFW700

21 Codin Product and Series Model Identification Frame size Rated current No. of phases Rated voltae Brakin ¹ Deree of Protection ¹ Conducted Emission Level ¹ Safety Stop ² External Power Supply for control CFW700 03P6 T 4 NB 20 C3 Y1 W1 NB = Brakin IGBT not available DB = Brakin IGBT available Check table below CFW = IP20 21 = IP21 ( not available for frame size E ) N1 = Nema1 Enclosure * Check table " enclosures " at chapter " ccessories ". Blank = with no RFI filter C3 = ccordin to cateory 3 of IEC standard Blank = with no STO function Y1 = with STO function accordin to EN / ISO , cateory 3 Blank = with no External Power supply board W1 = Control circuit is supplied throuh an external 24V power supply (1) To know what models have this options in the standard product the table below shall be checked (2)This option is not available for models frame size with the option for Nema1 Frame sizes B C D E B C D E Output Current ( ND) Input Power Supply Voltae Brakin Deree of protection Conducted emission level 06P0 = P0 = 7.0 B = sinle/three phase power supply 2 = V DB 20, 21 or N1 Blank 06P0 = P0 = 7.0 S = sinle phase power supply 2 = V DB 20, 21 or N1 C3 10P0 = 10 Blank or C3 07P0 = P0 = 10 13P0 = 13 16P0 = 16 24P0 = 24 20, 21 or N1 28P0 = 28 2 = V DB Blank or C3 33P5 = P0 = 45 S = three phase power supply 54P0 = 54 70P0 = 70 86P0 = = or N = = = V NB or DB 20 or N1 C = P0 = P0 = 7.0 B = sinle/three phase power supply 2 = V DB 20, 21 or N1 Blank 06P0 = 6 07P0 = 7.0 S = sinle phase power supply 2 = V DB 20, 21 or N1 C3 10P0 = 10 Blank or C3 3P6 = P0 = P0 = P0 = 10 13P5 = P0 = 17 20, 21 or N1 24P0 = 24 DB Blank or C3 31P0 = 31 38P0 = 38 T = three phase power supply 4 = V 45P0 = 45 58P5 = P5 = P0 = or N = = = 180 NB or DB 20 or N1 C = 211 Frequency Inverter Series - CFW700 21

22 Technical Data Voltae and Ratin Features Control Environment Brakin Methods Performance I/Os Sinle Phase Vac ( +10%-15%) Voltae Vac ( +10%-15%) Three Phase Vac ( +10%-15%) Sinle Phase 1.5 to 3HP (1.1 to 2.2kW) Power 1.5 to 75HP (1.1 to 55kW) Three Phase 2 to 175HP (1.5 to 110kW) Frequency Hz (+/-2%_48 to 63Hz) Displacement factor Greater than 0.98 Efficiency Greater than for three phase input at nominal conditional Power Factor 0.70 for sinle phase input at nominal conditional 0 to 3.4x motor rated frequency (P0403). The rated frequency is proramable up to 300Hz (V/Hz) and Frequency Rane 120Hz(vector mode). Switchin Frequency data must be observed for speed limits. Standard: 5kHz (,B,C D frames) 2.5kHz for all 380V models frame E 2.5kHz for frame E 220V models 142/180mps(ND) Switchin Frequency 2.5kHz for frame E 220V model 211mps(ND/HD) 5kHz for frame E 220V models 142/180mps(HD) vailable options for 2.5/5/10kHz( check for deratin) Overload Temperature Humidity ltitude Dynamic Brakin Optimal Brakin DC Brakin V/f Voltae Vector VVW Sensorless Vector Vector with Encoder ( Encoder Interface built-in) Sensorless Vector Inputs Output 24V power supply capacity Normal Duty(ND) Heavy Duty(HD) celeration Deceleration 110% for 1min every 10min 150% for 3s every 10min 150% for 1min every 10min 200% for 3s every 10min 0 to 999s 0 to 999s -10 to 50 C (14 to 122 F) for most of models. For operatin temperature of each model the table " Dimensions, Weiht and Temperature" shall be checked ºC for frames, B, C and D (up to 45 C without deratin for models 13 and 24/ V, 7 and 10/ V and up to 50 C without deratin for the other models) and C for frame E (up to 45 C without deratin). If deratin has to be considered have 2% current reduction for each C above the specific operatin temperature. 5 to 90% with no condensation 0 to 1000 meters with no deratin Up to 4000 meters with current reduction of 1% for each 100 meters above 1000 meters vailable as standard for frame sizes,b,c and D. For frame size E "DB" models has to be used. n extra resistor must be fitted in for dynamic brakin capability. There is no need for brakin resistor DC Current applied to motor Reulation: 1% of rated speed Speed Variation rane 1:20 Reulation: 1% of rated speed Speed Variation rane 1:30 Speed Control Reulation: 0.5% of rated speed Speed Variation rane 1:100 Reulation:+/- 0.1% of rated speed with diital reference (keypad, serial fieldbus, multispeed) Reulation:+/- 0.2% of rated speed with 12bits analo input Rane: 10 to 180% Torque Reulation: +/-5% of rated torque Control Rane: 20 to 180% Reulation: +/-10% of rated torque (above 3Hz)% Diital 8 x isolated bidirectional 24V 2 x +/-10V, 11bits + sinal(differencial) or 0/4...20m, 11bits(differencial) nalo Impedance: 400kΩ for voltae sinal / 500Ω for current sinal 1 x relay NO/NC contact(240vac/1) Relay 4 x open drain (24V/200m) 2 x V or 0/4...20m, 11 bits nalo (not isolated from inverter round) 500m ( available for the user, includin I/Os) 22 Frequency Inverter Series - CFW700

23 Technical Data Communication Safety Standards Mechanical Construccion Standards Eletromanetic Compatibility Standards ( EMC) Protections RS-485 built-in ( vailable at the control terminals) Modbus-RTU RS-485 built-in / Superdrive and WLP communication DeviceNet CN-01 ( slot 3) CNopen CN-01 ( slot 3) Profibus DP PROFIBUS DP-01 ( slot 3) UL 508C Power conversion equipment UL 840 Insulation coordination includin clearences and creepae distances for electrical equipment EN Safety requirements electrical, thermal and enery. EN Electronic equipment for use in power installations. EN Safety of machinery. Electrical equipment of machines. Part 1: General requirements. In order to have a machine in conformity with this reulation, the machine builder is resposible forthe installation of na emerency shutdown device and na equipment for power disconnection. EN (IEC 146) - Semiconductor converters. EN djustable speed electrical power drive systems - Part 2: General requirements - Ratin specifications for low voltae adjustable frequency.c. power drive systems EN Derees of protection provided by enclosures (IP code). UL 50 - Enclosures for electrical equipment EN djustable speed electrical power drive systems - Part 3: EMC product standard includin specifc test methods. EN Limits and methods of measurement of radio disturbance characteristics of undustrial, scientific and medical(ism) radio-frequency equipment. CISPR 11 - Industrial, scientifc and medical (ISM) radio-frequency equipment Eletromanetic disturbance characteristics - Limits and methods of measurement. EN Electromanetic compatibility (EMC) - Part 4: Testin and measurement techniques - Section 2: Eletrostatic dischare immunity test. EN Electromanetic compatibility (EMC) - Part 4: Testin and measurement techniques - Section 3: Radiated, radiofrequency, electromanetic feld immunity test. EN Electromanetic compatibility (EMC) - Part 4: Testin and measurement techniques - Section 4: Electrical fast transient/burst immunity test. EN Electromanetic compatibility (EMC) - Part 4: Testin and measurement techniques - Section 5: Sure immunity test. EN Electromanetic compatibility (EMC)- Part 4: Testin and measurement techniques - Section 6: Immunity to conducted disturbances, induced by radio-frequency fields. Overcurrent / Short Circuit Under / Overvoltae in the power section Phase Loss VSD thermal Overload ( IGBTs, rectifier and in the eletronics) Motor thermal overload Brakin resistor overload IGBTs overload Motor overload Fault / external alarm CPU failure Phase-to round short circuit at the output Failure at the heatsink fan Motor Overspeed Wron connection of encoder wirin Frequency Inverter Series - CFW700 23

24 WEG Worldwide Operations RGENTIN WEG EQUIPMIENTOS ELECTRICOS S.. (Headquarters San Francisco-Cordoba) So. Pampilione 4849 Parque Industrial San Francisco San Francisco Phone: +54 (3564) Fax: +54 (3564) info-ar@we.net USTRLI WEG USTRLI PTY. LTD. 3 Dalmore Drive Carribean Park Industrial Estate Scoresby VIC Melbourne Phone: 61 (3) Fax: 61 (3) info-au@we.net BELGIUM WEG BENELUX S.. Rue de l Industrie 30 D, 1400 Nivelles Phone: + 32 (67) Fax: + 32 (67) info-be@we.net CHILE WEG CHILE S.. Los Canteros 8600 La Reina - Santiao Phone: (56-2) Fax: (56-2) info-cl@we.net CHIN WEG (NNTONG) ELECTRIC MOTOR MNUFCTURING CO., LTD. No. 128# - Xinkai South Road, Nanton Economic & Technical Development Zone, Nanton, Jiansu Province. Phone: (86) Fax: (86) info-cn@we.net COLOMBI WEG COLOMBI LTD Calle 46 N82-54 Portería II - Bodea 7 - San Cayetano II - Bootá Phone: (57 1) Fax: (57 1) info-co@we.net WEG Equipamentos Elétricos S.. International Division v. Prefeito Waldemar Grubba, Jarauá do Sul - SC - Brazil Phone: 55 (47) Fax: 55 (47) DENMRK WEG Scandinavia Denmark Sales Office of WEG Scandinavia B nelysparken 43B True 8381 Tilst Denmark Phone: Fax : info-se@we.net FRNCE WEG FRNCE SS ZI de Chenes Le Loup 13 Rue du Morellon BP Saint Quentin Fallavier Phone: +33 (0) Fax: +33 (0) info-fr@we.net GERMNY WEG GERMNY GmbH Industrieebiet Türnich 3 Geierstraße Kerpen-Türnich Phone: +49 (0)2237/ Fax: +49 (0)2237/ info-de@we.net GHN ZEST ELECTRIC GHN LIMITED - WEG Group 15, Third Close Street irport Residential rea, ccra PMB CT 175, Cantonments Phone: Fax: info@zesthana.com.h INDI WEG Electric (India) Pvt. Ltd. #38, Ground Floor, 1st Main Road, Lower Palace Orchards, Banalore Phone(s): Fax: info-in@we.net ITLY WEG ITLI S.R.L. V.le Brianza Cinisello Balsamo - Milano Phone: (39) Fax: (39) info-it@we.net JPN WEG ELECTRIC MOTORS JPN CO., LTD. Yokohama Sky Buildin 20F, Takashima, Nishi-ku, Yokohama City, Kanaawa, Japan Phone: (81) info-jp@we.net MEXICO WEG MEXICO, S.. DE C.V. Carretera Jorobas-Tula Km. 3.5, Manzana 5, Lote 1 Fraccionamiento Parque Industrial - Huehuetoca, Estado de México - C.P Phone: + 52 (55) Fax: + 52 (55) info-mx@we.net NETHERLNDS WEG NETHERLNDS Sales Office of WEG Benelux S.. Hanzepoort 23C 7575 DB Oldenzaal Phone: +31 (0) Fax: +31 (0) info-nl@we.net PORTUGL WEG EURO - INDÚSTRI ELÉCTRIC, S.. Rua En. Frederico Ulrich partado Maia Phone: Fax: info-pt@we.net RUSSI WEG RUSSI Russia, , St. Petersbur, Prospekt Kultury 44, Office 419 Phone: +7(812) Fax: +7(812) info-ru@we.net SOUTH FRIC ZEST ELECTRIC MOTORS (PTY) LTD. WEG Group 47 Galaxy venue, Linbro Business Park - Gauten Private Ba X Sandton, 2146 Johannesbur Phone: (27-11) Fax: (27-11) info@zest.co.za SPIN WEG IBERI S.L. venida de la Industria, Coslada - Madrid Phone: (34) Fax : (34) info-es@we.net SINGPORE WEG SINGPORE PTE LTD 159, Kampon mpat, #06-02 K PLCE. Sinapore Phone: Fax: info-s@we.net SWEDEN WEG SCNDINVI B Box Verkstadatan Kunsbacka Phone: (46) Fax: (46) info-se@we.net UK WEG ELECTRIC MOTORS (U.K.) LTD. 28/29 Walkers Road Manorside Industrial Estate North Moons Moat - Redditch Worcestershire B98 9HE Phone: 44 (0) Fax: 44 (0) info-uk@we.net UNITED RB EMIRTES WEG MIDDLE EST FZE JFZ JEBEL LI FREE ZONE Tower 18, 19th Floor, Office LB P.O. Box Dubai Phone: +971 (4) Fax: +971 (4) info-ae@we.net US WEG ELECTRIC CORP Suarloaf Parkway, Duluth, G Phone: Fax: info-us@we.net VENEZUEL WEG INDUSTRIS VENEZUEL C.. venida 138- Edificio Torre Banco Occidental de Descuento, Piso 6 Oficina 6-12 Urbanizacion San Jose de Tarbes Zona Postal 2001 Valencia, Edo. Carabobo Phone(s): (58) (58) (58) Fax: (58) info-ve@we.net Cod: Rev: 01 Date (m/y): 02/2011 The values shown are subject to chane without prior notice.