INSTALL GUIDE OEM-NI(RS)-NI6-[ADS-NI5]-EN

Transcription

1 INSTLL GUIDE DOCUMENT NUMER REVISION DE 00 FIRMWRE OEM-NI(RS)-NI-[DS-NI] HRDWRE DS-NI CCESSORIES DS-US (REQUIRED) TERMS OF USE: utomotive Data Solutions Inc. ( DS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an DS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. DS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. DS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. EFORE INSTLLION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)

2 VEHICLE LIST - OF PGE OF DOC.: # 00 FEURES MKE INFINITI MODEL YER INSTLL TYPE D IMMOILIZER YPSS SECURE TKE OVER DISRM OEM LRM DOOR LOCK DOOR UNLOCK X LOCK /STNDLONE MOD. POWER LIFT GE POWER SLIDING DOORS (L) POWER SLIDING DOORS (R) TRUNK/HCH RELESE DOOR STUS OUTPUT TRUNK STUS OUTPUT HOOD STUS OUTPUT** TCHOMETER OUTPUT RKE PEDL STUS OUTPUT * E-RKE STUS OUTPUT M Hybrid - M 0 M - M 0 M - Q0 - Q0L - QX - QX0 - rmada Cube 0- Juke - Quest - Quest (with power sliding doors) - Sentra - Versa Sedan - Versa Note - * vailable only when ignition is in the ON position. ** vailable only if vehicle is equipped with factory hood switch. NISSN

3 OX CONTENTS - OF PGE OF DOC.: # 00 OX CONTENTS MODULE T-HRNESS VS 0 PIN LUE LCK 0 0 LED LED G F E PROGRMMING UTTON LCK RF PORT/ WELINK PORT LUE TELEMIC PORT LCK MS MS VS VS VS VS VS PIN OPTIONL TERMINLS (OEM LRM CONTROL) LCK 0 C D 0 WHITE MS VS VS FTERMRKET HOOD SWITCH ND CLE VS VS0 WRNING STICKER VS VS WELINK CLE (required accessory sold separately) WELINK CLE MODULE WELINK PORT COMPUTER US PORT PIN LCK CLE

4 TYPE - WIRE CHRT - OF PGE OF DOC.: # 00 MKE INFINITI MODEL YER WIRE DESCRIPTION NME COLOR TYPE POSITION WIRE COLOR POLRITY MODULE LOCION COMPONENT LOCOR NISSN M Hybrid M M Q0 Q0L QX QX0 rmada Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ pin 0 lue (+) Driver kick panel ~ Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ pin 0 lue (+) Driver kick panel ~ Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ pin 0 lue (+) Fuse box, rear side ~ Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ pin 0 lue (+) Driver kick panel ~ Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ pin 0 lue (+) Driver kick panel ~ Lock/rm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M lack pin Gray/Red (-) CM, behind cluster ~ Parking Light M White 0 pin lue/orange (+) Fuse box ~ Lock/rm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M lack pin Gray/Red (-) CM, behind cluster ~ Parking Light M White 0 pin lue/orange (+) Fuse box ~ Lock/rm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M lack pin Gray/Red (-) CM, behind cluster ~ Parking Light M White 0 pin lue/orange (+) Fuse box ~

5 TYPE - WIRE CHRT - OF PGE OF DOC.: # 00 MKE MODEL YER NISSN WIRE DESCRIPTION NME COLOR TYPE POSITION WIRE COLOR POLRITY MODULE LOCION COMPONENT LOCOR Lock/rm M lack 0 pin 0 White/lack (-) CM, driver kick panel ~ Cube Unlock/Disarm M lack 0 pin 0 White/Red (-) CM, driver kick panel ~ 0- Driver Door Pin M lack pin rown/yellow (-) CM, driver kick panel ~ Parking Light M0 ~ pin rown/white (+) Driver kick panel ~ Lock/rm M lack 0 pin 0 Red (-) CM near pillar, driver side ~ Juke Unlock/Disarm M lack 0 pin 0 lue (-) CM near pillar, driver side ~ - Driver Door Pin 0 lack pin Ltlue (-) CM near pillar, driver side ~ Parking Light M ~ 00 pin 0 Violet (+) Driver kick panel ~ Lock/rm M lack 0 pin 0 Yellow (-) CM, behind cluster ~ Quest* Unlock/Disarm M lack 0 pin 0 White (-) CM, behind cluster ~ - Driver Door Pin M lack pin Green (-) CM, behind cluster ~ Parking Light M ~ 0 pin Ltlue (+) Fuse box ~ Lock/rm M lack 0 pin 0 Gray (-) CM, behind cluster ~ Quest* Unlock/Disarm M lack 0 pin 0 rown (-) CM, behind cluster ~ - Driver Door Pin M lack pin Green (-) CM, behind cluster ~ Parking Light M ~ 0 pin Pink (+) Fuse box ~ Lock/rm M lack 0 pin 0 Gray (-) CM near pillar, driver side ~ Versa Sedan Unlock/Disarm M lack 0 pin 0 White (-) CM near pillar, driver side ~ - Driver Door Pin 0 lack Pin Ltlue (-) CM near pillar, driver side ~ Parking Light ~ pin 0 lue (+) Driver kick panel ~ * Model without power sliding doors

6 TYPE - WIRING DIGRM - OF PGE OF DOC.: # 00 MODULE C G F E D RF PORT/WELINK PORT TELEMIC PORT MS VS VS PIN ODII PIN ODII HRNESS ODII (UNDER DRIVER SIDE DSH) 0 MS RELY VS PIN RKE RKE SWITCH E VS PIN RKE HRNESS E 0 0 MS VS VS VS VS0 VS PIN PIN HRNESS LOCK CC ENGINE ON VS VS PIN IMMO IMMO C D 0 0 ROWN/LCK 0 GRY - RP SHUTDOWN (-) OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 EMPTY 0 LUE/GREEN 0 EMPTY 0 EMPTY GRY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT WHITE OPTIONL VS PIN IMMO HRNESS PRKING LIGHT (+) HORN (-) DRIVER DOOR PIN (-) - SEE WIRE CHRT 0 CM 0 0 GRY/WHITE - HOOD STUS (-) INPUT THERE MY E NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINLS. LOCK/RM (-) UNLOCK/DISRM (-) SEE WIRE CHRT WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH FTERMRKET HOOD SWITCH (-)

7 TYPE - WIRE CHRT - OF PGE OF DOC.: # 00 NISSN MKE MODEL YER WIRE DESCRIPTION NME COLOR TYPE POSITION WIRE COLOR POLRITY MODULE LOCION COMPONENT LOCOR Quest* Lock/rm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ - Driver Door Pin M lack pin Green (-) CM, behind cluster ~ Parking Light M ~ 0 pin Ltlue (+) Fuse box ~ Quest* Lock/rm M lack 0 pin Empty (-) CM, behind cluster (use provided terminal for connection) ~ - Driver Door Pin M lack pin Green (-) CM, behind cluster ~ Parking Light M ~ 0 pin Pink (+) Fuse box ~ * Model with power sliding doors

8 TYPE - WIRING DIGRM - OF PGE OF DOC.: # 00 MODULE C G F E D RF PORT/WELINK PORT TELEMIC PORT MS VS VS PIN ODII PIN ODII HRNESS ODII (UNDER DRIVER SIDE DSH) 0 MS RELY VS PIN RKE RKE SWITCH E VS PIN RKE HRNESS E 0 0 MS VS VS VS VS0 VS PIN PIN HRNESS LOCK CC ENGINE ON VS VS PIN IMMO IMMO C D 0 0 ROWN/LCK 0 GRY - RP SHUTDOWN (-) OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 EMPTY 0 LUE/GREEN 0 EMPTY 0 EMPTY GRY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN WHITE OPTIONL VS PIN IMMO HRNESS PRKING LIGHT (+) HORN (-) DRIVER DOOR PIN (-) - SEE WIRE CHRT M M 0 CM 0 0 GRY/WHITE - HOOD STUS (-) INPUT DIODE N00 DIODE N00 THERE MY E NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINLS. LOCK/RM (-) - M M M WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH M FTERMRKET HOOD SWITCH (-)

9 TYPE - WIRE CHRT - OF PGE OF DOC.: # 00 MKE MODEL YER INFINITI WIRE DESCRIPTION NME COLOR TYPE POSITION WIRE COLOR POLRITY MODULE LOCION COMPONENT LOCOR M M 0 0 Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ ~ ~ ~ Red/lue (+) Driver kick panel ~ Lock/rm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Unlock/Disarm M0 lack 0 pin Empty (-) CM, left of steering column (use provided terminal for connection) ~ Driver Door Pin M lack pin LtGreen (-) CM, left of steering column ~ Parking Light ~ ~ ~ ~ Red/lue (+) Driver kick panel ~

10 TYPE - WIRING DIGRM - OF PGE 0 OF DOC.: # 00 MODULE C G F E D RF PORT/WELINK PORT TELEMIC PORT MS VS VS PIN ODII PIN ODII HRNESS ODII (UNDER DRIVER SIDE DSH) 0 MS RELY VS PIN RKE RKE SWITCH E VS PIN RKE HRNESS E 0 0 MS VS VS VS VS VS0 VS VS PIN PIN HRNESS PIN IMMO LOCK CC ENGINE ON IMMO C D 0 0 ROWN/LCK 0 GRY - RP SHUTDOWN (-) OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 EMPTY 0 LUE/GREEN 0 EMPTY 0 EMPTY GRY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT WHITE OPTIONL VS PIN IMMO HRNESS PRKING LIGHT (+) HORN (-) DRIVER DOOR PIN (-) - SEE WIRE CHRT M M 0 CM 0 0 GRY/WHITE - HOOD STUS (-) INPUT LOCK/RM (-) - UNLOCK/DISRM (-) - THERE MY E NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINLS. M0 M0 M WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH M0 FTERMRKET HOOD SWITCH (-)

11 TYPE - WIRE CHRT - OF PGE OF DOC.: # 00 MKE MODEL YER NISSN WIRE DESCRIPTION NME COLOR TYPE POSITION WIRE COLOR POLRITY MODULE LOCION COMPONENT LOCOR Sentra Versa Note - - Lock/rm M lack 0 pin Purple or White/Purple (-) CM near pillar, driver side ~ Unlock/Disarm M lack 0 pin lue or White/lue (-) CM near pillar, driver side ~ Driver Door Pin 0 lack pin Yellow (-) CM near pillar, driver side ~ Parking Light ~ White pin 0 Purple or White/Purple (+) Driver kick panel ~ Lock/rm M lack 0 pin Gray (-) CM near pillar, driver side ~ Unlock/Disarm M lack 0 pin White (-) CM near pillar, driver side ~ Driver Door Pin 0 lack pin Ltlue (-) CM near pillar, driver side ~ Parking Light M White pin 0 Red (+) Driver kick panel ~

12 TYPE - WIRING DIGRM - OF PGE OF DOC.: # 00 MODULE C G F E D RF PORT/WELINK PORT TELEMIC PORT MS VS VS PIN ODII PIN ODII HRNESS ODII (UNDER DRIVER SIDE DSH) 0 MS RELY VS PIN RKE RKE SWITCH E VS PIN RKE HRNESS E 0 0 MS VS VS VS0 VS VS PIN PIN HRNESS LOCK CC ENGINE ON VS VS PIN IMMO IMMO C D 0 0 ROWN/LCK 0 GRY - RP SHUTDOWN (-) OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 EMPTY 0 LUE/GREEN 0 EMPTY 0 EMPTY GRY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT WHITE OPTIONL VS PIN IMMO HRNESS PRKING LIGHT (+) SEE WIRE CHRT HORN (-) DRIVER DOOR PIN (-) CM 0 0 GRY/WHITE - HOOD STUS (-) INPUT LOCK/RM (-) - UNLOCK/DISRM (-) - M M 0 WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH M FTERMRKET HOOD SWITCH (-)

13 HOLD E MODULE PROGRMMING PROCEDURE - OF PGE OF DOC.: # 00 0 When programming, only one keyfob will be used. Place the other one at least 0 feet away from the vehicle. 0 Wait, LED will turn solid RED. Wait, LED will flash GREEN rapidly. 0 Remove valet key from keyfob. 0 Wait seconds or until the security light flashes. (The security light may not appear.) CC ON Push start button once [x] to OFF position. ENGINE 0 Remove battery from keyfob. 0 Press and release brake pedal once [x]. WRNING: Disconnect power last. Disconnect module from vehicle. >> IMPORTNT: Place and hold keyfob on push to start button for steps to. 0 Wait, LED will turn solid GREEN. Connect module to computer and proceed with extended programming. 0 LOCK CC N G I N ON Place and hold keyfob on push to start button (no battery). Keyfob transponder is located behind keyfob logo. 0 Wait seconds or until the security light flashes. (The security light may not appear.) Connect power first. Connect module to vehicle. 0 CC ON Push start button twice [x] to ON position. Press and release brake pedal once [x]. >> IMPORTNT: Place and hold keyfob on push to start button for steps to. ENGINE

14 E MODULE PROGRMMING PROCEDURE - OF PGE OF DOC.: # 00 LOCK CC N G I N ON Place and hold keyfob on push to start button (no battery). Keyfob transponder is located behind keyfob logo. Wait until the key symbol light turns OFF. CC ON Push start button twice [x] to ON position. ENGINE 0 Wait, LED will turn solid GREEN for seconds. CC ON Push start button once [x] to OFF position. ENGINE Module Programming Procedure completed.

15 VLET MODE PROGRMMING PROCEDURE - OF PGE OF DOC.: # 00 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within seconds. 0 OFF CC ON Cycle ignition ON five times [x OFF/ON] rapidly. ENGINE 0 Wait, LED will turn solid RED for seconds. 0 OFF CC ON Set ignition to OFF position. ENGINE 0 Valet Mode Programming Procedure completed.

16 PGE OF MODULE NVIGION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to OFF position. 0 TO CCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 0 OFF CC ON DOC.: # 00 TO CCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO CCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MNDORY: EXIT MODULE NVIGION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE 0 0 [X]

17 MODULE NVIGION CHRT - OF PGE OF DOC.: # 00 MODULE NVIGION CHRT: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 CONFIGURION 0 DISRM/UNLOCK EFORE 0 OFF 0 ON 0 RELOCK FTER 0 OFF 0 ON 0 RELOCK FTER SHUTDOWN 0 OFF 0 ON 0 FORCE UNLOCK LL ON FIRST PRESS 0 OFF 0 ON 0 TKEOVER 0 ENLE 0 DISLE* 0 N/ 0 N/ 0 DISLE 0 FCTORY KEYLESS RS SEQUENCE 0 N/ 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SEC 0 0 SEC 0 0 SEC 0 WIT TO DELY 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 N/ 0 N/ N/ 0 N/ N/ 0 N/ N/ 0 N/

18 MODULE NVIGION CHRT - OF PGE OF DOC.: # 00 MODULE NVIGION CHRT: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 0 DOULE LOCK HORN EVENT TRIGGER 0 LOCK + UNLOCK 0 LOCK + UNLOCK + 0 CONFIGURION 0 DOULE LOCK msec HORN CHIRPS WIDTH 0 msec 0 0 msec 0-0 Technical Support only 0 N/ 0 N/

19 REMOTE ER ERROR CODES - OF PGE OF DOC.: # 00 REMOTE ER ERROR CODES: NOTES [X] NUMER OF PRKING LIGHT FLSHES DIGNOSTIC I II WRNING: The following applies only when the parking lights are connected and supported by the system. fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. 0 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 N/ N/ N/ N/ N/ N/ CN communication failure during RS sequence.

20 MODULE DIGNOSTICS - OF PGE 0 OF DOC.: # 00 TEST MODULE LED STUS DIGNOSTIC I II III DURING PROGRMMING DURING REMOTE WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. dditional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.

21 MODULE RESET PROCEDURE - OF PGE OF DOC.: # 00 0 Disconnect all connectors from module except the LCK 0-PIN connector. 0 Reconnect all connectors. 0 Disconnect the LCK 0-PIN connector. 0 Repeat programming procedure. 0 PRESS ND HOLD the module s programming button while connecting the LCK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELESE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed.

22 TKEOVER PROCEDURE - - OF PGE OF DOC.: # 00 >> ll vehicle doors must be closed and locked prior to remote start sequence. 0 Take over procedure completed. 0 Time restriction. Complete steps to within seconds. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Open driver door and enter vehicle. 0 Close driver door. 0 Press and release RKE pedal.

23 INSTLLION CHECKLIST - OF PGE OF DOC.: # 00 CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. Installation checklist completed.