INSTALL GUIDE OEM-AL(RS)-VW2-[ADS-ALCA]-EN

Transcription

1 INSTLL GUIDE OEM-L(RS)-VW-[DS-LC]-EN DOCUMENT NUMER 89 REVISION DTE 008 FIRMWRE OEM-L(RS)-VW-[DS-LC] HRDWRE DS-LC CCESSORIES DS-US (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. utomotive Data Solutions Inc. 0 EFORE INSTLLTION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)

2 PGE OF DOC.: # VEHICLE LIST - OF FETURES NOTE YER SECURE TKEOVER X LOCK STRT/STNDLONE MOD. RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK TRUNK/HTCH RELESE DOOR STTUS OUTPUT TRUNK STTUS OUTPUT HOOD STTUS OUTPUT* UTOLIGHT CTRL TCHOMETER OUTPUT RKE PEDL STTUS OUTPUT E-RKE OUTPUT Keyport with PTS T 08- Keyport without PTS T 08- llroad Keyport with PTS T 08- llroad Keyport without PTS T 08- Keyport with PTS T 08- Keyport without PTS T 08- Q Keyport with PTS T 09- Q Keyport without PTS T 09- Q TDI Keyport with PTS T 09- Q TDI Keyport without PTS T 09- RS Keyport with PTS T 08- RS Keyport without PTS T 08- S Keyport with PTS T 08- S Keyport without PTS T 08- S Keyport with PTS T 08- S Keyport without PTS T 08- SQ Keyport with PTS T SQ Keyport without PTS T *vailable only if vehicle is equipped with factory hood switch. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN INSTLL TYPE MODEL UDI MKE I Warning: Install type supports idle mode. Install type does NOT support idle mode.

3 PGE OF DOC.: # OX CONTENTS - OF OX CONTENTS WHITE WHITE PIN LCK CONNECTOR PIN WHITE CONNECTOR MODULE WHITE LUE PROGRMMING UTTON 0 PIN LCK CONNECTOR PIN WHITE CONNECTOR LED F C E D LCK PIN WHITE CONNECTOR DT CLE PIN LUE CONNECTOR DT CLE LCK DT PORT (WELINK, RF, TELEMTIC) WELINK CLE (required accessory sold separately) WELINK CLE MODULE DT PORT COMPUTER US PORT PIN LCK CLE utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN

4 PGE OF DOC.: # TECHNICL NOTE - OF IMPORTNT STRTER WIRE CONNECTION FOR VEHICLES WITH UTOMTIC TRNSMISSION. lack connector at brake switch under the dashboard, near the brake pedal. t the ECU under the wiper cowl, located under the hood, in the engine compartement. (IF PRESENT) OR utomotive Data Solutions Inc. 0 STRTER FROM RS OEM-L(RS)-VW-[DS-LC]-EN K C ) L (+ D/ E RE RK K C ) L (+ D/ E RE RK STRTER FROM RS

5 PGE OF DOC.: # UDI Keyport with PTS T llroad Keyport with PTS T S Keyport with PTS T Keyport with PTS T RS Keyport with PTS T S Keyport with PTS T Q Keyport with PTS T Q TDI Keyport with PTS T SQ Keyport with PTS T utomotive Data Solutions Inc WIRE COLOR MODULE LOCTION COMPONENT LOCTOR Red/lack ehind fuse box 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen POLRITY POSITION CONNECTOR TYPE CONNECTOR NME V rake CONNECTOR COLOR WIRE DESCRIPTION YER MODEL MKE TYPE - WIRE CHRT - OF CanL Orange/rown Ignition lack ehind fusebox PTS 0 pin 0 lue/yellow Push-button PTS 0 pin 0 lue/white Push-button Keysense pin 0 lack/yellow V Red/lack ehind fuse box rake 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen CanL Orange/rown lack Ignition ehind fusebox PTS 0 pin 0 lue/yellow Push-button PTS 0 pin 0 lue/white Push-button Keysense pin 0 lack/yellow V Red/lack ehind fuse box rake 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen CanL Orange/rown Ignition lack ehind fusebox PTS 0 pin 0 lue/yellow Push-button PTS 0 pin 0 lue/white Push-button Keysense pin 0 lack/yellow OEM-L(RS)-VW-[DS-LC]-EN

6 PGE OF DOC.: # TYPE - WIRING DIGRM - OF MODULE PTS SWITCH PTS PTS - 0 PTS - 0 F C E DT D 0 GRY/YELLOW (NC) 0 GRY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED - PTS OUTPUT 0 LUE/YELLOW (NC) 0 LUE/RED (NC) 0 PINK - IGNITION INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - KEYSENSE OUTPUT 0 ORNGE/LCK - PTS OUTPUT 0 ROWN/YELLOW - CNL 0 ROWN/RED - CNH CNL CNH IGNITION 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) 0 WHITE - V CONSTNT 0 WHITE/RED (NC) 0 WHITE/LCK D RKE SWITCH N00 RKE - 0 F LUE/WHITE (NC) WHITE (NC) LCK - GROUND RED - V 8 WITHOUT COMPTILE CCESSORY 8 0 REMOVE TTERY OR E EHIND FUSE OX V DIODE C TWISTED WIRES IN DOOR HRNESS IN DRIVER KICK PNEL DT CLE COMPTILE CCESSORY 0 GREEN/LCK- HOOD STTUS INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) 0 ROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/LCK (NC) 0 WHITE (NC) 08 LCK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) TWO KEYS RE REQUIRED FOR THIS INSTLLTION. ONE KEY WILL REMIN PERMNENTLY IN THE VEHICLE. THE OTHER KEY WILL E USED FOR THE PROGRMMING PROCEDURE. IT WILL THEN E RETURNED TO THE OWNER. utomotive Data Solutions Inc. 0 WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS.. 0 LOOPS (0 WG) ROUND KEYFO V KEYPORT 0 LOOPS (0 WG) ROUND KEYPORT KEYSENSE - 0 WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH - CONNECTOR EHIND KEYPORT FTERMRKET HOOD SWITCH OEM-L(RS)-VW-[DS-LC]-EN

7 PGE OF DOC.: # utomotive Data Solutions Inc. 0 Red/lack ehind fuse box 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen CanL Orange/rown lack ehind fusebox PTS pin 0 lack PTS pin lack/red PTS pin Gray/lue Keysense pin 0 lack/yellow V Red/lack ehind fuse box rake 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen CanL Orange/rown lack ehind fusebox PTS pin 0 lack PTS pin lack/red PTS pin Gray/lue Keysense pin 0 lack/yellow V Red/lack ehind fuse box rake 0 pin 0 Red/lack t brake switch CanH Orange/LtGreen CanL Orange/rown lack ehind fusebox PTS pin 0 lack PTS pin lack/red PTS pin Gray/lue Keysense pin 0 lack/yellow 08- Ignition 08- Ignition 09- Ignition OEM-L(RS)-VW-[DS-LC]-EN POLRITY CONNECTOR TYPE CONNECTOR COLOR V rake CONNECTOR NME COMPONENT LOCTOR WIRE DESCRIPTION MODULE LOCTION Q Keyport without PTS T Q TDI Keyport without PTS T SQ Keyport without PTS T WIRE COLOR Keyport without PTS T RS Keyport without PTS T S Keyport without PTS T POSITION UDI Keyport without PTS T llroad Keyport without PTS T S Keyport without PTS T YER MODEL MKE TYPE - WIRE CHRT - OF

8 PGE 8 OF DOC.: # TYPE - WIRING DIGRM - OF MODULE TWISTED WIRES IN DOOR HRNESS IN DRIVER KICK PNEL CNL CNH F IGNITION C 0 GRY/YELLOW (NC) 0 GRY/RED - PTS OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - PTS OUTPUT 0 LUE/YELLOW (NC) 0 LUE/RED (NC) 0 PINK - IGNITION INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - KEYSENSE OUTPUT 0 ORNGE/LCK - PTS OUTPUT 0 ROWN/YELLOW - CNL 0 ROWN/RED - CNH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) 0 WHITE - V CONSTNT 0 WHITE/RED (NC) 0 WHITE/LCK C D EHIND FUSE OX V E DT D RKE SWITCH N00 RKE - 0 DIODE REMOVE TTERY 0 LOOPS (0 WG) ROUND KEYFO E LUE/WHITE (NC) WHITE (NC) LCK - GROUND RED - V KEYPORT WITHOUT COMPTILE CCESSORY OR F DT CLE COMPTILE CCESSORY 0 GREEN/LCK- HOOD STTUS INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) 0 ROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/LCK (NC) 0 WHITE (NC) 08 LCK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) TWO KEYS RE REQUIRED FOR THIS INSTLLTION. ONE KEY WILL REMIN PERMNENTLY IN THE VEHICLE. THE OTHER KEY WILL E USED FOR THE PROGRMMING PROCEDURE. IT WILL THEN E RETURNED TO THE OWNER. utomotive Data Solutions Inc. 0 WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS.. V 0 LOOPS (0 WG) ROUND KEYPORT PTS - PTS - PTS - 0 KEYSENSE CONNECTOR EHIND KEYPORT WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH FTERMRKET HOOD SWITCH OEM-L(RS)-VW-[DS-LC]-EN

9 MODULE PROGRMMING PROCEDURE - OF 0 PGE 9 OF DOC.: # Push start button twice [x] to ON position. STOP CC ON STRT ENGINE STRT STOP 0 0 Wait, LED will turn solid GREEN then will turn. Push start button once [x] to position. STOP CC ON STRT ENGINE STRT STOP 0 Module Programming Procedure completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN

10 VLET MODE PROGRMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within seconds. 0 CC ON STRT >> PGE 0 OF DOC.: # To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. ENGINE STRT STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. CC ON STRT ENGINE STRT STOP 0 Valet Mode Programming Procedure completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN

11 PGE OF DOC.: # MODULE NVIGTION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. 0 TO CCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously CC ON STRT TO CCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO CCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MNDTORY: EXIT MODULE NVIGTION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STRT STOP 0 0 [X] utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN

12 PGE OF DOC.: # [Y] OPTIONS [X] MENUS MODULE NVIGTION CHRT: NOTES I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 DISRM/UNLOCK EFORE STRT RELOCK FTER STRT RELOCK FTER SHUTDOWN 0 ON 0 0 ON 0 0 ON 0 0 ON FORCE UNLOCK LL ON FIRST PRESS 0 N/ 0 N/ 0 N/ 0 N/ 0 DISLE 0 N/ 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 08 0 SEC 0- N/ 0 N/ 0 0 N/ FCTORY KEYLESS RS SEQUENCE CONFIGURTION Technical Support only [Z] SETTINGS MODULE NVIGTION CHRT - OF MODULE RUN TIME WIT TO STRT DELY N/ *Vehicle will shutdown when a door is opened. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN

13 [X] NUMER OF PRKING LIGHT FLSHES DIGNOSTIC REMOTE STRTER ERROR CODES - OF I WRNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 08 Glow plug timeout error. REMOTE STRTER ERROR CODES: NOTES utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN PGE OF DOC.: #89 008

14 I II III DURING PROGRMMING DURING REMOTE STRT WITH IGNITION utomotive Data Solutions Inc. 0 DIGNOSTIC TEST MODULE LED STTUS MODULE DIGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN dditional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. OEM-L(RS)-VW-[DS-LC]-EN PGE OF DOC.: #89 008

15 MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the LCK -PIN connector. 0 Reconnect all connectors. 0 Disconnect the LCK -PIN connector. 08 Repeat programming procedure. 0 PRESS ND HOLD programming button while connecting the LCK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELESE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN PGE OF DOC.: #89 008

16 INSTLLTION CHECKLIST - OF PGE OF DOC.: # CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[DS-LC]-EN