INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN

Transcription

1 INSTALL GUIDE DOCUMENT NUMBER 545 REVISION DATE FIRMWARE OEM-AL(RS)-TL7-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)

2 VEHICLE LIST - OF PAGE OF 0 FEATURES MAKE MODEL YEAR INSTALL TYPE LEXUS DATA IMMOBILIZER BYPASS X LOCK START/STANDALONE MOD. PUSH TO START CTRL ARM OEM ALARM DISARM OEM ALARM A/M ALARM CTRL FROM OEM REMOTES A/M RS CTRL FROM OEM REMOTES PRIORITY UNLOCK** DOOR LOCK** DOOR UNLOCK** TRUNK/HATCH RELEASE** DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT IS00t AT 6 IS00t AT 7 IS50 AT 4-5 IS00 AT 6 IS00 AT 7-8 IS50 AT 4-6 IS50 AT 7-8 LX570 AT 6-8 NX00T AT NX00h AT 7 4 NX00t AT 8 RC00 AT 7-8 RC50 AT 5-8 RX50 AT 6-8 RX450h AT Camry AT 8 5 Camry Hybrid AT 8 6 C-HR AT 8 Highlander AT 4-6 Highlander AT 7-8 Highlander Hybrid AT 4-6 Highlander Hybrid AT 7-8 Land Cruiser AT 6-8 Prius AT 6-8 Prius Prime AT 7-8 Tacoma AT 6-8 *Available only if vehicle is equipped with factory hood switch. **See technical note on page 5. TOYOTA

3 BOX CONTENTS - OF PAGE OF 0 DOC.: # BOX CONTENTS MODULE 6 PIN WHITE 4 PIN BLACK WHITE PROGRAMMING BUTTON LED 7 PIN WHITE 0 PIN BLACK WHITE WHITE M M M M BLACK PIN WHITE DATA CABLE BLUE M4 M5 4 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT 4 PIN BLACK CABLE

4 TECHNICAL NOTE - OF PAGE 4 OF 0 WARNING: DOOR LOCK SYNCHRONIZATION The door lock signal is encrypted on select models. In order for the bypass to operate properly, it must be synchronized with that encrypted signal. However, when the vehicle is driven, data is sent along the bus that desynchronizes the bypass with the encryption. To regain synchronization once the engine is shut off, the bypass must see the factory keyless codes (OEM remote or proximity lock/unlock codes). This solution will resynchronize automatically upon seeing the first factory keyless code and will operate normally (both convenience and immobilizer bypass/remote starter functionality). Conversely, if the vehicle is driven and the factory keyless system is not used to lock or unlock, the aftermarket remote will not be able to lock or unlock until the bypass receives factory keyless code at least once as described above. Finally, as factory keyless operates normally during remote start with this solution and take-over is not supported, a one-button remote control is a very good choice for these vehicles in order to prevent any possible user issues.

5 COMPONENT LOCATOR - OF PAGE 5 OF 0 INTERIOR VIEW C F A B E D DRIVER SIDE VIEW PASSENGER SIDE VIEW

6 TYPE - CHART - OF PAGE 6 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION LEXUS POLARITY MODULE LOCATION COMPONENT LOCATOR IS00t IS50 IS00 IS CanH N0 Black 6 pin 06 White (DATA) OBDII connector D CanL N0 Black 6 pin 4 Black (DATA) OBDII connector D V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH N0 Black 6 pin 06 White (DATA) OBDII connector D CanL N0 Black 6 pin 4 Black (DATA) OBDII connector D V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH N0 Black 6 pin 06 White (DATA) OBDII connector D CanL N0 Black 6 pin 4 Black (DATA) OBDII connector D V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH N0 Black 6 pin 06 White (DATA) OBDII connector D CanL N0 Black 6 pin 4 Black (DATA) OBDII connector D V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A

7 TYPE - CHART - OF PAGE 7 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE TOYOTA POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Highlander Highlander Hybrid CanH F5 White 6 pin 06 Purple (DATA) OBDII connector D CanL F5 White 6 pin 4 White (DATA) OBDII connector D V F54 Black 07 pin 07 Black (+) Steering lock B Ignition F54 Black 07 pin 06 Red (+) Steering lock B SLP F54 Black 07 pin 04 LtGreen (-) Steering lock B F49 Black 0 pin 0 Purple (-) button C Parking Light K White 0 pin 08 Black ~ Main Body ECU A Parking Light K White 0 pin LtGreen (-) Main Body ECU A CanH F5 White 6 pin 06 Purple (DATA) OBDII connector D CanL F5 White 6 pin 4 White (DATA) OBDII connector D V F54 Black 07 pin 07 Black (+) Steering lock B Ignition F54 Black 07 pin 06 Red (+) Steering lock B SLP F54 Black 07 pin 04 LtGreen (-) Steering lock B F49 Black 0 pin 0 Purple (-) button C Parking Light K White 0 pin 08 Black ~ Main Body ECU A Parking Light K White 0 pin LtGreen (-) Main Body ECU A

8 TYPE - WIRING DIAGRAM - OF PAGE 8 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 CANL - 4 CANH - 06 WITHOUT OEM HOOD STATUS ONLY IGNITION (+) OBDII STEERING LOCK M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 7.5A SLP (-) - 04 V (+) M4 0 WHITE (NC) 0 WHITE/RED - PARKING LIGHT SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE MAIN BODY ECU (DRIVER SIDE DASH) M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) M5 DATA CABLE COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. PARKING LIGHT - 08 PARKING LIGHT (-) M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

9 TYPE - CHART - OF PAGE 9 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE TOYOTA POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Prius Prius Prime CanH ~ White 0 pin 4 LtBlue (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ White 6 pin 6 Purple (+) OBDII connector D Ignition ~ White pin 0 Purple (+) Dash fuse box A Starter ~ Black 54 pin 04 Black (+) Hybrid vehicle control ECU, behind glove box E ~ Black 0 pin 0 Green (-) button C Auto light ~ White 0 pin 08 Black or White (-) Main Body ECU A Parking Light ~ White 0 pin Tan (-) Main Body ECU A CanH ~ White 0 pin 4 LtBlue (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ White 6 pin 6 Purple (+) OBDII connector D Ignition ~ White pin 0 Purple (+) Dash fuse box A Starter ~ Black 54 pin 04 Black (+) Hybrid vehicle control ECU, behind glove box E ~ Black 0 pin 0 Green (-) button C Auto light ~ White 0 pin 08 Black or White (-) Main Body ECU A Parking Light ~ White 0 pin Tan (-) Main Body ECU A

10 TYPE - WIRING DIAGRAM - OF PAGE 0 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT 7.5A CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 V (+) OBDII M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE - STARTER (+) OUTPUT 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) M4 0 WHITE (NC) 0 WHITE/RED - AUTOLIGHT SIDE 0 WHITE/BLACK - AUTOLIGHT VEHICLE SIDE WITHOUT OEM HOOD STATUS ONLY STARTER (+) HYBRID VEHICLE CONTROL ECU, BEHIND GLOVE BOX M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) M5 DATA CABLE M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. AUTOLIGHT - 08 CANL - CANH - 4 PARKING LIGHT (-) - IGNITION (+) MAIN BODY ECU (DRIVER SIDE DASH) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

11 TYPE - CHART - OF PAGE OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION LEXUS POLARITY MODULE LOCATION COMPONENT LOCATOR IS00t AT IS00 AT IS50 AT LX CanH F9 White 0 pin 4 Yellow (DATA) Main Body ECU A CanL F9 White 0 pin Black (DATA) Main Body ECU A V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH F9 White 0 pin 4 Yellow (DATA) Main Body ECU A CanL F9 White 0 pin Black (DATA) Main Body ECU A V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH F9 White 0 pin 4 Yellow (DATA) Main Body ECU A CanL F9 White 0 pin Black (DATA) Main Body ECU A V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH ~ White 0 pin 4 Green (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ Black 07 pin 07 Green (+) Steering lock B Ignition ~ Black 07 pin 06 Pink (+) Steering lock B SLP ~ Black 07 pin 04 Red (-) Steering lock B ~ Black 0 pin 0 Blue (-) button C Parking Light ~ White 0 pin 08 Pink (-) Main Body ECU A Parking Light ~ White 0 pin Black (-) Main Body ECU A

12 TYPE - CHART - OF PAGE OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION LEXUS POLARITY MODULE LOCATION COMPONENT LOCATOR NX00t RC00 RC50 RX CanH I48 White 0 pin 4 Yellow (DATA) Main Body ECU, below dash fusebox D CanL I48 White 0 pin White (DATA) Main Body ECU, below dash fusebox D V I Black 07 pin 07 Blue (+) Steering lock B Ignition I Black 07 pin 06 Pink (+) Steering lock B SLP I Black 07 pin 04 Yellow (-) Steering lock B I6 Black 0 pin 0 Green (-) button C Parking Light I48 White 0 pin 08 Green ~ Main Body ECU, below dash fusebox D Parking Light I48 White 0 pin Pink (-) Main Body ECU, below dash fusebox D CanH F9 White 0 pin 4 Black (DATA) Main Body ECU A CanL F9 White 0 pin White (DATA) Main Body ECU A V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH F9 White 0 pin 4 Black (DATA) Main Body ECU A CanL F9 White 0 pin White (DATA) Main Body ECU A V N4 Black 07 pin 07 Green (+) Steering lock B Ignition N4 Black 07 pin 06 Black (+) Steering lock B SLP N4 Black 07 pin 04 Red (-) Steering lock B N46 Black 0 pin 0 Blue (-) button C Parking Light F9 White 0 pin 08 Pink ~ Main Body ECU A Parking Light F9 White 0 pin Black (-) Main Body ECU A CanH ~ White 0 pin 4 LtBlue (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ Black 07 pin 07 Purple (+) Steering lock B Ignition ~ Black 07 pin 06 Pink (+) Steering lock B SLP ~ Black 07 pin 04 Gray (-) Steering lock B ~ Black 0 pin 0 Purple (-) button C Parking Light ~ White 0 pin 08 Green (-) Main Body ECU A Parking Light ~ White 0 pin Purple (-) Main Body ECU A

13 TYPE - CHART - OF PAGE OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION TOYOTA POLARITY MODULE LOCATION COMPONENT LOCATOR C-HR AT Highlander / Highlander Hybrid AT Land Cruiser Tacoma CanH ~ White 0 pin 4 Green (DATA) Main Body ECU A CanL ~ White 0 pin LtBlue (DATA) Main Body ECU A V ~ Black 07 pin 07 Blue (+) Steering lock B Ignition ~ Black 07 pin 06 Black (+) Steering lock B SLP ~ Black 07 pin 04 Green (-) Steering lock B ~ Black 0 pin 0 Gray (-) button C Parking Light ~ White 0 pin 08 White ~ Main Body ECU A Parking Light ~ White 0 pin Yellow (-) Main Body ECU A CanH K White 0 pin 4 Red (DATA) Main Body ECU A CanL K White 0 pin White (DATA) Main Body ECU A V F54 Black 07 pin 07 Black (+) Steering lock B Ignition F54 Black 07 pin 06 Red (+) Steering lock B SLP F54 Black 07 pin 04 LtGreen (-) Steering lock B F49 Black 0 pin 0 Purple (-) button C Parking Light K White 0 pin 08 Black ~ Main Body ECU A Parking Light K White 0 pin LtGreen (-) Main Body ECU A CanH ~ White 0 pin 4 Green (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ Black 07 pin 07 Green (+) Steering lock B Ignition ~ Black 07 pin 06 Pink (+) Steering lock B SLP ~ Black 07 pin 04 Red (-) Steering lock B ~ Black 0 pin 0 Blue (-) button C Parking Light ~ White 0 pin 08 Pink (-) Main Body ECU A Parking Light ~ White 0 pin Black (-) Main Body ECU A CanH ~ White 0 pin 4 Black (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ Black 07 pin 07 Red (+) Steering lock B Ignition ~ Black 07 pin 06 Black (+) Steering lock B SLP ~ Black 07 pin 04 Tan (-) Steering lock B ~ Black 0 pin 0 Gray (-) button C Parking Light ~ White 0 pin 08 White ~ Main Body ECU A Parking Light ~ White 0 pin Green (-) Main Body ECU A

14 TYPE - WIRING DIAGRAM - OF PAGE 4 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT 7.5A CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 SLP (-) - 04 IGNITION (+) - 06 V (+) STEERING LOCK M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) M4 0 WHITE (NC) 0 WHITE/RED - PARKING LIGHT SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE WITHOUT OEM HOOD STATUS ONLY PARKING LIGHT - 08 CANL - CANH - 4 PARKING LIGHT (-) - MAIN BODY ECU (DRIVER SIDE DASH) M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY OR M5 DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

15 TYPE 4 - CHART - OF PAGE 5 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TYPE LEXUS POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR NX00T NX00h CanH OBDII White 6 pin 06 Black (DATA) OBDII connector D CanL OBDII White 6 pin 4 White (DATA) OBDII connector D V I Black 07 pin 07 Blue (+) Steering lock B Ignition I Black 07 pin 06 Pink (+) Steering lock B SLP I Black 07 pin 04 Yellow (-) Steering lock B I6 Black 0 pin 0 Green (-) button C Parking Light I48 White 0 pin 08 Green ~ Main Body ECU, below dash fusebox D Parking Light I48 White 0 pin Pink (-) Main Body ECU, below dash fusebox D CanH OBDII White 6 pin 06 Black (DATA) OBDII connector D CanL OBDII White 6 pin 4 White (DATA) OBDII connector D V I Black 07 pin 07 Blue (+) Steering lock B Ignition I Black 07 pin 06 Pink (+) Steering lock B SLP I Black 07 pin 04 Yellow (-) Steering lock B I6 Black 0 pin 0 Green (-) button C Parking Light I48 White 0 pin 08 Green ~ Main Body ECU, below dash fusebox D Parking Light I48 White 0 pin Pink (-) Main Body ECU, below dash fusebox D

16 TYPE 4 - WIRING DIAGRAM - OF PAGE 6 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 CANL - 4 CANH OBDII M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH WITHOUT OEM HOOD STATUS ONLY IGNITION (+) STEERING LOCK M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 7.5A SLP (-) - 04 V (+) M4 0 WHITE (NC) 0 WHITE/RED - PARKING LIGHT SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE MAIN BODY ECU - BELOW DASH FUSEBOX M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY OR M5 M6 DATA CABLE 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. PARKING LIGHT - 08 PARKING LIGHT (-) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

17 TYPE 5 - CHART - OF PAGE 7 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TOYOTA TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH K5 Black 0 pin 05 Tan (DATA) Main Body ECU/Dash fuse box A CanL K5 Black 0 pin 04 White (DATA) Main Body ECU/Dash fuse box A V ~ Black 07 pin 07 Purple (+) Steering lock B Camry AT 8 Ignition ~ Black 07 pin 06 LtGreen (+) Steering lock B SLP ~ Black 07 pin 04 Tan (-) Steering lock B ~ Black 0 pin 0 Gray (-) switch C Autolights ~ White 40 pin 05 White or Yellow (-) Headlamp switch F Parking Light ~ White 40 pin 0 Blue/Black or Green (-) Headlamp switch F

18 TYPE 5 - WIRING DIAGRAM - OF PAGE 8 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 7.5A CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 SLP (-) - 04 IGNITION (+) - 06 V (+) - 07 WITHOUT OEM HOOD STATUS ONLY K STEERING LOCK MAIN BODY ECU /DASH FUSEBOX M M4 0 WHITE (NC) 0 WHITE/RED - AUTOLIGHTS (-) SIDE 0 WHITE/BLACK - AUTOLIGHTS (-) VEHICLE SIDE M5 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) M5 DATA CABLE COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. CANL - 04 CANH K5 M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) PARKING LIGHT (-) - 0 AUTOLIGHTS (-) HEAD LAMP SWITCH IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

19 TYPE 6 - CHART - OF PAGE 9 OF 0 MAKE MODEL YEAR DESCRIPTION NAME TOYOTA TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH K5 Black 0 pin 05 Tan (DATA) Main Body ECU/Dash fuse box A CanL K5 Black 0 pin 04 White (DATA) Main Body ECU/Dash fuse box A V ~ Black 07 pin 07 Purple (+) Steering lock B Camry Hybrid AT 8 Ignition ~ Black 07 pin 06 LtGreen (+) Steering lock B SLP ~ Black 07 pin 04 Tan (-) Steering lock B Starter ~ Gray 5 pin 09 LtBlue (+) Hybrid ECU, right of driver dash fusebox A ~ Black 0 pin 0 Gray (-) switch C Autolights ~ White 40 pin 05 White or Yellow (-) Headlamp switch F Parking Light ~ White 40 pin 0 Blue/Black or Green (-) Headlamp switch F

20 TYPE 6 - WIRING DIAGRAM - OF PAGE 0 OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE - STARTER (+) OUTPUT 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M M4 0 WHITE (NC) 0 WHITE/RED - AUTOLIGHTS (-) SIDE 0 WHITE/BLACK - AUTOLIGHTS (-) VEHICLE SIDE M5 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 04 RED - V (+) M5 DATA CABLE COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 7.5A CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 SLP (-) - 04 IGNITION (+) - 06 V (+) - 07 WITHOUT OEM HOOD STATUS ONLY CANL - 04 CANH - 05 K STEERING LOCK MAIN BODY ECU /DASH FUSEBOX K5 HEAD LAMP SWITCH M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) PARKING LIGHT (-) - 0 AUTOLIGHTS (-) HYBRID ECU GRAY STARTER (+) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

21 TYPE 7 - CHART - OF PAGE OF 0 MAKE MODEL YEAR DESCRIPTION NAME TOYOTA TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH ~ White 0 pin 4 LtBlue (DATA) Main Body ECU A CanL ~ White 0 pin White (DATA) Main Body ECU A V ~ Black 07 pin 07 Purple (+) Steering lock B RX450h 6-8 Ignition ~ Black 07 pin 06 Pink (+) Steering lock B SLP ~ Black 07 pin 04 Gray (-) Steering lock B ~ Black 0 pin 0 Purple (-) button C Parking Light ~ White 0 pin 08 Green (-) Main Body ECU A Parking Light ~ White 0 pin Purple (-) Main Body ECU A Starter ~ White 7 pin 7 LtGreen (+) Certification ecu behind glove box E

22 TYPE 7 - WIRING DIAGRAM - OF PAGE OF 0 SWITCH M M M M4 M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 04 GREEN/RED - SLP (-) OUTPUT 05 BLUE/YELLOW - (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE - STARTER (+) OUTPUT 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) M4 0 WHITE (NC) 0 WHITE/RED - PARKING LIGHT SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE M5 0 BLUE/WHITE (NC) WITHOUT A 0 WHITE (NC) COMPATIBLE 0 BLACK - GROUND ACCESSORY 04 RED - V (+) OR 7.5A CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED (-) - 0 SLP (-) - 04 IGNITION (+) - 06 V (+) - 07 WITHOUT OEM HOOD STATUS ONLY PARKING LIGHT - 08 CANL - CANH - 4 PARKING LIGHT (-) STEERING LOCK MAIN BODY ECU (DRIVER SIDE DASH) M5 DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. CERTIFICATION ECU, BEHIND GLOVEBOX M6 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) STARTER (+) IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

23 MODULE PROGRAMMING PROCEDURE - OF PAGE OF 0 0 STOP ACC ON START Push start button twice [x] to ON position. 07 STOP ACC ON START Push start button once [x] to OFF position. ENGINE START STOP ENGINE START STOP 0 Wait, if LED turns solid GREEN for seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step. 08 Module Programming Procedure completed. 0 STOP ACC ON START Push start button once [x] to OFF position. ENGINE START STOP 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 05 STOP ACC ON START Push start button twice [x] to ON position. ENGINE START STOP 06 Wait, LED will turn solid GREEN for seconds.

24 VALET MODE PROGRAMMING PROCEDURE - OF PAGE 4 OF 0 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to 5. 0 Time restriction. Complete next step within 7 seconds. 0 OFF ACC ON START Cycle ignition ON five times [5x OFF/ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 04 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP 05 Valet Mode Programming Procedure completed.

25 PAGE 5 OF 0 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously OFF ACC ON START DOC.: # TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X]

26 MODULE NAVIGATION CHART - OF PAGE 6 OF 0 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE START 0 OFF 0 ON 0 RELOCK AFTER START 0 OFF 0 ON 0 RELOCK AFTER SHUTDOWN 0 OFF 0 ON 04 FORCE UNLOCK ALL ON FIRST PRESS 0 OFF 0 ON 05 N/A 0 N/A 06 N/A 0 N/A 0 DISABLE 07 FACTORY KEYLESS RS SEQUENCE 0 N/A 0 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 0 0 MIN 0 CONFIGURATION 0 05 MIN 0 0 MIN 08 MODULE RUN TIME 04 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 08 5 MIN 0 0 SEC 0 05 SEC 0 08 SEC 09 WAIT TO START DELAY 04 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A

27 REMOTE STARTER ERROR CODES - OF PAGE 7 OF 0 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 04 Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error.

28 MODULE DIAGNOSTICS - OF PAGE 8 OF 0 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.

29 MODULE RESET PROCEDURE - OF PAGE 9 OF 0 0 Disconnect all connectors from module except the BLACK 4-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 4-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed.

30 INSTALLATION CHECKLIST - OF PAGE 0 OF 0 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed.