PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

Transcription

1 PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

2 GETTING ED PAGE 2 OF WELCOME Congratulations on the purchase of your FT-DC2 solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your FT-DC2 module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TABLE OF CONTENTS Box Contents 3 Tach Programming Procedure 4 Remote Programming Procedure 5 Valet Mode Programming Procedure 6 Compatible Accessories 7 Online Module Settings 9 Module Diagnostics 0 Remote Starter Error Codes Module Reset Procedure 2 NEED HELP? support@idatalink.com idatalink.com/support Automotive Data Solutions Inc. 206 FT-DC2-S

3 BOX CONTENTS - OF PAGE 3 OF BOX CONTENTS AUTOMATIC TRANSMISSION CUT LOOP M2-2 PIN BLACK M3-0 PIN WHITE DRONE - 4 PIN GRAY RF PORT - 4 PIN BLUE M5-6 PIN BLUE M4-20 PIN BLACK 2 PIN WHITE - LED 2 PIN BLUE - THERMISTOR PROGRAMMING BUTTON M2 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 EMPTY 05 EMPTY 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 BROWN BLACK DOT - SIREN (+) OUTPUT 08 EMPTY 09 PURPLE/BLACK BLACK DOT - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - GROUND WHEN ARMED (-) OUTPUT 2 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT LED 2 FT-DAS - 4 PIN RED FT-DAS SENSITIVTY ADJUSTMENT DIAL WEBLINK PORT - 4 PIN BLACK LED M3 0 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 EMPTY 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 EMPTY 0 TAN SILVER DOT - EXT ALARM SENSOR (-) INPUT M FUNCTIONS DEFINED BY FIRMWARE STICKERS HOOD SWITCH 2X M FUNCTIONS DEFINED BY FIRMWARE A omotive Data Solutions Inc. 206 FT-DC2-S

4 CH PROGRAMMING PROCEDURE - OF PAGE 4 OF OFF ACC ON S ART vehicle for 5 seconds. 02 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) 04 Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. Automotive Data Solutions Inc. 206 FT-DC2-S

5 AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF PAGE 5 OF >> W ogram aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. 06 Parking Light will flash once [x]. 0 Time restriction. Complete next step within 7 seconds. >> To program additional remotes: repeat steps 4 to 6 using each additional remote. 02 OFF ACC ON Cycle ignition ON ive times [5x OFF/ON] rapidly. 07 Wait, Parking Light will flash twice [2x]. 03 Parking Light will flash once [x]. 08 OFF ACC ON Turn ignition to OFF position. 04 Time restriction. Complete next step within 5 seconds from previous step. 09 Aftermarket Remote Programming Procedure completed. 05 Press once [x] on LOCK button of aftermarket remote. Automotive Data Solutions Inc. 206 FT-DC2-S

6 VALET MODE PROGRAMMING PROCEDURE - OF PAGE 6 OF >> NTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to OFF ACC ON Cycle ignition ON twice [2x OFF/ON] rapidly. 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [x] then will flash twice [2x]. 05 OFF ACC ON Set ignition to OFF position. Automotive Data Solutions Inc. 206 FT-DC2-S

7 TIBLE ACCESSORIES - OF 2 PAGE 7 OF WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT OBDII CONNECTOR TELEMATIC KIT (accessory sold separately) DRONE MODULE TELEMATIC PORT (NC) Automotive Data Solutions Inc. 206 FT-DC2-S

8 TIBLE ACCESSORIES - 2 OF 2 PAGE 8 OF RF KIT (accessories sold separately) RF KIT MODULE RF PORT ANTENNA ALARM KIT (accessories sold separately) MODULE 2 PIN BLACK 07 BROWN BLACK DOT - SIREN (+) OUTPUT RED BLACK SIREN MODULE 2 PIN WHITE ALARM LED FT-DAS MODULE 4 PIN RED TEMPERATURE SENSOR (accessories sold separately) TEMPERATURE SENSOR MODULE 2 PIN BLUE Automotive Data Solutions Inc. 206 FT-DC2-S

9 ONLINE MODULE SETTINGS - OF PAGE 9 OF WEB PROGRAMMABLE MENUS MENU Remote Starter MENU 2 Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Coniguration (PTO) MENU 7 Input Conigurations MENU 8 Output Conigurations Programming options are avaible through Weblink and Weblink Mobile only. DESCRIPTION RS related coniguration options Convenience feature coniguration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by irmware/data/analog Set outputs for Auto by irmware/data/analog Automotive Data Solutions Inc. 206 FT-DC2-S

10 MODULE DIAGNOSTICS - OF PAGE 0 OF TEST MODULE LED STATUS DIAGNOSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITION OFF Flashing RED Missing/wrong information from irmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. GREEN flash Tach signal programmed in Analog 2 GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. Automotive Data Solutions Inc. 206 FT-DC2-S

11 REMOTE ER ERROR CODES - OF PAGE OF REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 E! "# $ 02 Key % & '% () *&+ % &$ 03 Door is open. 04 Trunk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. REMOTE ER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 02 Emergency brake is lost. 03 Foot brake is ON. 04 Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. Automotive Data Solutions Inc. 206 FT-DC2-S

12 MODULE RESET PROCEDURE - OF PAGE 2 OF >> T,-.ollow/0 23ocedure resets the module programming to the vehicle. It does not reset any settings conigured online. 06 Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. 02 Disconnect the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for 2 seconds. Automotive Data Solutions Inc. 206 FT-DC2-S

13 INSTALL GUIDE 206 LEXUS IS200T PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

14 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T00_W Automotive Data Solutions Inc Lexus IS200t PTS AT

15 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) WHITE - 06 CANL (DATA) BLACK M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) BLUE - 29 TRUNK (-) PINK - 05 SLP (-) RED - 04 IGNITION (+) BLACK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T00_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus IS200t PTS AT

16 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus IS200t PTS AT

17 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus IS200t PTS AT

18 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus IS200t PTS AT

19 INSTALL GUIDE LEXUS IS250 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

20 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T00_W Automotive Data Solutions Inc Lexus IS250 PTS AT

21 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) WHITE - 06 CANL (DATA) BLACK M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) BLUE - 29 TRUNK (-) PINK - 05 SLP (-) RED - 04 IGNITION (+) BLACK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T00_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus IS250 PTS AT

22 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus IS250 PTS AT

23 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus IS250 PTS AT

24 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus IS250 PTS AT

25 INSTALL GUIDE 206 LEXUS IS300 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

26 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T00_W Automotive Data Solutions Inc Lexus IS300 PTS AT

27 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) WHITE - 06 CANL (DATA) BLACK M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) BLUE - 29 TRUNK (-) PINK - 05 SLP (-) RED - 04 IGNITION (+) BLACK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T00_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus IS300 PTS AT

28 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus IS300 PTS AT

29 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus IS300 PTS AT

30 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus IS300 PTS AT

31 INSTALL GUIDE LEXUS IS350 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

32 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T00_W Automotive Data Solutions Inc Lexus IS350 PTS AT

33 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) WHITE - 06 CANL (DATA) BLACK M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) BLUE - 29 TRUNK (-) PINK - 05 SLP (-) RED - 04 IGNITION (+) BLACK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T00_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus IS350 PTS AT

34 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus IS350 PTS AT

35 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus IS350 PTS AT

36 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus IS350 PTS AT

37 INSTALL GUIDE 206 LEXUS LX570 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

38 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF A C D B T006_W Automotive Data Solutions Inc Lexus LX570 PTS AT

39 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OEM REMOTE ER CONNECTOR, BEHIND GLOVEBOX (B) CANH (DATA) TAN - 02 CANL (DATA) GRAY - 0 : WHITE M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) PINK - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) GREEN - 29 TRUNK (-) BLACK - 05 SLP (-) RED - 04 IGNITION (+) PINK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T006_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus LX570 PTS AT

40 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus LX570 PTS AT

41 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus LX570 PTS AT

42 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus LX570 PTS AT

43 INSTALL GUIDE 205 LEXUS NX200T PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

44 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T002_W Automotive Data Solutions Inc Lexus NX200T PTS AT

45 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) GREEN - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) BLACK - 06 CANL (DATA) WHITE M2 M3 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) GREEN - 08 LOCK (-) RED - 29 POWER LIFTGATE (-) RED - 05 MAIN BODY ECU, DRIVER SIDE DASH (C) : WHITE : WHITE M4 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 SLP (-) YELLOW - 04 IGNITION (+) PINK V (+) BLUE - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T002_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus NX200T PTS AT

46 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus NX200T PTS AT

47 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus NX200T PTS AT

48 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus NX200T PTS AT

49 INSTALL GUIDE 205 LEXUS RC350 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

50 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T004_W Automotive Data Solutions Inc Lexus RC350 PTS AT

51 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) BLUE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) WHITE - 06 CANL (DATA) BLACK M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTGREEN - 02 AUTOLIGHT (-) PINK - 08 LOCK (-) BLUE - 29 TRUNK (-) PINK - 05 SLP (-) RED - 04 IGNITION (+) BLACK V (+) GREEN - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T004_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus RC350 PTS AT

52 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus RC350 PTS AT

53 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus RC350 PTS AT

54 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus RC350 PTS AT

55 INSTALL GUIDE 206 LEXUS RX350 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

56 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF A C D B T007_W Automotive Data Solutions Inc Lexus RX350 PTS AT

57 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) PURPLE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED NETWORK GATEWAY ECU, BEHIND GLOVEBOX (B) CANH (DATA) LTBLUE - 06 CANL (DATA) WHITE - 2 M2 M3 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY UNLOCK (-) PURPLE - 02 AUTOLIGHT (-) GREEN - 08 LOCK (-) PINK - 29 : BLACK MAIN BODY ECU, DRIVER SIDE DASH (C) : WHITE : WHITE M4 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 TRUNK (-) RED - 05 SLP (-) GRAY - 04 IGNITION (+) PINK V (+) PURPLE - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T007_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Lexus RX350 PTS AT

58 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Lexus RX350 PTS AT

59 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Lexus RX350 PTS AT

60 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Lexus RX350 PTS AT

61 INSTALL GUIDE TOYOTA HIGHLANDER HYBRID PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

62 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T003_W Automotive Data Solutions Inc Toyota Highlander Hybrid PTS AT

63 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) PURPLE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) PURPLE - 06 CANL (DATA) WHITE M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTBLUE - 02 AUTOLIGHT (-) BLACK - 08 LOCK (-) PURPLE - 29 TRUNK (-) GRAY - 05 SLP (-) LTGREEN - 04 IGNITION (+) RED V (+) BLACK - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T003_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Toyota Highlander Hybrid PTS AT

64 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Toyota Highlander Hybrid PTS AT

65 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Toyota Highlander Hybrid PTS AT

66 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Toyota Highlander Hybrid PTS AT

67 INSTALL GUIDE TOYOTA HIGHLANDER PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

68 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF C D A B T003_W Automotive Data Solutions Inc Toyota Highlander PTS AT

69 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) PURPLE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED OBDII (B) CANH (DATA) PURPLE - 06 CANL (DATA) WHITE M2 M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 UNLOCK (-) LTBLUE - 02 AUTOLIGHT (-) BLACK - 08 LOCK (-) PURPLE - 29 TRUNK (-) GRAY - 05 SLP (-) LTGREEN - 04 IGNITION (+) RED V (+) BLACK - 07 WITHOUT OEM HOOD STATUS ONLY HORN (-) 2 : WHITE : WHITE MAIN BODY ECU, DRIVER SIDE DASH (C) 2 STEERING LOCK (D) M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3 T003_W Automotive Data Solutions Inc. 206 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Toyota Highlander PTS AT

70 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Toyota Highlander PTS AT

71 INSTALLATION CHECKLIST - OF 2 PAGE 5 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. Automotive Data Solutions Inc Toyota Highlander PTS AT

72 INSTALLATION CHECKLIST - 2 OF 2 PAGE 6 OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Toyota Highlander PTS AT

73 INSTALL GUIDE 207 TOYOTA HIGHLANDER PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-TL7-[FT-DC2-S] HARDWARE FT-DC2-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 206

74 HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF B C A T009_W Automotive Data Solutions Inc Toyota Highlander PTS AT

75 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF ! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (-) PURPLE - 0 PTS SWITCH (A) CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED MAIN BODY ECU, DRIVER SIDE DASH (B) UNLOCK (-) LTBLUE - 02 : WHITE M2 M3 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY AUTOLIGHT (-) BLACK - 08 CANL (DATA) WHITE - 3 CANH (DATA) RED - 4 LOCK (-) PURPLE - 29 TRUNK (-) GRAY - 05 SLP (-) LTGREEN : WHITE STEERING LOCK (C) M4 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED - SLP (-) OUTPUT 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - GROUND (-) INPUT 7 PINK - IGNITION (+) IN/OUT 8 PURPLE 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 2 IGNITION (+) RED V (+) BLACK - 07 WITHOUT OEM HOOD STATUS ONLY M5 0 GRAY/BLACK BLUE DOT - PTS (-) OUTPUT 02 WHITE/BLACK BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE 05 GRAY BLUE DOT - GROUND (-) INPUT 06 WHITE BLUE DOT T009_W Automotive Data Solutions Inc. 206 HORN (-) HOOD SWITCH 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE Toyota Highlander PTS AT

76 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF ACC ON Push start button twice [2x] to ON position. 07 ACC ON Push start button once [x] to OFF position. 3 Module Programming Procedure completed. 02 Wait, if LED turns solid GREEN for 2 seconds, proceed to step 7. If LED flashes GREEN rapidly, proceed to step ACC ON vehicle for 5 seconds. 03 ACC ON Push start button once [x] to OFF position. 09 Press and hold the brake pedal. 04 Wait, LED will turn solid RED. (This may take up to 5 minutes.) 0 Press and release the module s programming button. 05 ACC ON Push start button twice [2x] to ON position. Release the brake pedal. 06 Wait, LED will turn solid GREEN for 2 seconds. 2 Wait, LED 2 will flash GREEN. Automotive Data Solutions Inc Toyota Highlander PTS AT