INSTALL GUIDE DIR-IDS(RS)-BZ3-[ADS-BZ3]-EN

Transcription

1 INSTLL GUIDE DIR-IDS(RS)-BZ3-[DS-BZ3]-EN DOCUMENT NUMBER REVISION DTE 2627 FIRMWRE DIR-IDS(RS)-BZ3-[DS-BZ3] HRDWRE DS-BZ3 CCESSORIES DS-USB (REQUIRED) DIRECTED XL-2 RF-KIT & DS-HRN(RS)-XL (OPTIONL) DIRECTED SMRTSTRT & DS-HRN(RS)-SM (OPTIONL) DS-TOOLS-MB (OPTIONL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. utomotive Data Solutions Inc. 26 BEFORE INSTLLTION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)

2 PGE 2 OF 28 DOC.: # VEHICLE LIST - 1 OF 2 FETURES 3X LOCK STRT/STNDLONE MOD. SECURE TKEOVER DT IMMOBILIZER BYPSS RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HTCH RELESE PRKING LIGHT CTRL HETED SETS CTRL VENTILTED SETS CTRL RP SHUTDOWN CTRL TCHOMETER STTUS MONITORING BRKE PEDL STTUS MONITORING VSS STTUS MONITORING DOOR STTUS MONITORING TRUNK STTUS MONITORING HOOD STTUS MONITORING* C-Class MG Coupe STD key T C-Class MG Sedan PTS T C-Class MG Sedan STD key T C-Class Coupe PTS T C-Class Coupe STD key T C-Class Sedan PTS T C-Class Sedan STD key T CLS-Class MG Sedan PTS T CLS-Class MG Sedan STD key T CLS-Class Sedan PTS T CLS-Class Sedan STD key T E-Class MG Sedan PTS T E-Class MG Sedan STD key T E-Class MG Wagon PTS T E-Class MG Wagon STD key T E-Class Coupe PTS T E-Class Coupe STD key T E-Class Sedan Diesel PTS T E-Class Sedan Diesel STD key T E-Class Sedan PTS T E-Class Sedan STD key T E-Class Wagon PTS T utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN INSTLL TYPE MKE MERCEDES-BENZ E-Class Wagon STD key T * If equipped with a factory hood switch. GLOW PLUG STTUS MONITORING YER C-Class MG Coupe PTS T II ll the covered Push To Start (PTS) vehicles are equipped with a keyless authorization system called "Keyless Go". POWER LIFTGTE MODEL NOTES I This firmware covers utomatic Transmission (T) vehicles only.

3 PGE 3 OF 28 DOC.: # VEHICLE LIST - 2 OF 2 FETURES YER 3X LOCK STRT/STNDLONE MOD. SECURE TKEOVER DT IMMOBILIZER BYPSS RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK POWER LIFTGTE PRKING LIGHT CTRL HETED SETS CTRL VENTILTED SETS CTRL RP SHUTDOWN CTRL TCHOMETER STTUS MONITORING BRKE PEDL STTUS MONITORING VSS STTUS MONITORING GLOW PLUG STTUS MONITORING DOOR STTUS MONITORING TRUNK STTUS MONITORING HOOD STTUS MONITORING* GLK-Class Diesel PTS T GLK-Class Diesel PTS T GLK-Class Diesel STD key T GLK-Class Diesel STD key T GLK-Class PTS T GLK-Class PTS T GLK-Class STD key T GLK-Class STD key T SLK-Class MG PTS T SLK-Class MG STD key T SLK-Class PTS T MERCEDES-BENZ SLK-Class STD key T * If equipped with a factory hood switch. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN INSTLL TYPE MKE II ll the covered Push To Start (PTS) vehicles are equipped with a keyless authorization system called "Keyless Go". TRUNK/HTCH RELESE MODEL NOTES I This firmware covers utomatic Transmission (T) vehicles only.

4 PGE 4 OF 28 DOC.: # BOX CONTENTS - 1 OF 1 BOX CONTENTS MODULE LED 1 LED 2 PROGRMMING BUTTON USB BLCK BLCK BLCK BLUE BLCK 2 1 BLUE BLCK BLUE TELEMTIC PORT 12 PIN BLCK CONNECTOR FTERMRKET HOOD SWITCH ND CBLE WHITE BLCK H-HRNESS 1 2 PIN BLCK CONNECTOR BLCK RF PORT/WEBLINK PORT EXPNSION PCK SSEMBLY EXTR CONNECTOR HOUSING EXPNSION PCK BLCK RED XP LED 1 XP LED 2 LED LED STICKER 1 TOP VIEW BLUE 10 PIN WHITE CONNECTOR T-HRNESS BOTTOM VIEW STICKER 2 TOP VIEW BLCK WEBLINK CBLE (required accessory sold separately) ELECTRONIC IGNITION SWITCH REMOVL TOOL (accessory sold separately) WEBLINK CBLE MODULE WEBLINK PORT COMPUTER USB PORT IGNITION SWITCH DS-TOOLS-MB OR MERCEDEZ BENZ P/N PIN BLCK CBLE utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

5 PGE 5 OF 28 DOC.: # COMPTIBLE CCESSORIES - 1 OF 1 RF KIT (accessories sold separately) DS-HRN(RS)-XL DIRECTED XL2 RF KIT MODULE RF PORT XL2 RF DECODER XL2 NTENN TELEMTIC KIT (accessories sold separately) DS-HRN(RS)-SM DIRECTED SMRTSTRT (NC) MODULE TELEMTIC PORT (NC) (NC) utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

6 TECHNICL NOTE - 1 OF 1 IMPORTNT PGE 6 OF 28 DOC.: # INSTLL VIDEO GLLERY VILBLE ONLINE Before installing this product, consult our Install Video Gallery and watch: Vehicle Disassembly Procedure videos Module Connection Procedures videos Module Programming Procedures videos Æ To access the videos, simply log in your Weblink user account, and click on "Install videos" under the "Support" tab. Æ Then, select a vehicle make, year and model to display the available videos. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

7 PGE 7 OF 28 DOC.: # COMPONENT LOCTOR - 1 OF 1 INTERIOR VIEW DRIVER SIDE VIEW utomotive Data Solutions Inc. 26 PSSENGER SIDE VIEW DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

8 PGE 8 OF 28 DOC.: # MODULE INSTLLTION PROCEDURE - 1 OF 1 CC ON STRT CC ON STRT STRT the vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. 07 Turn the vehicle. 08 ENGINE STRT STOP CC ON STRT WRNING: ny vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. n OEM scantool will be required to clear the error messages. 13 If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING DIGRM. STRT the vehicle. Verify all vehicle functionalities. 14 If required, connect a compatible RF Kit to the RF port of the module. RF ENGINE STRT STOP ENGINE STRT STOP 03 Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and RFID access if equipped) Insert the expansion pack in the module. 10 CC WRNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. 15 If required, connect a compatible Telematics Device to the TELEMTIC port of the module. Turn the vehicle. 16 Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector. 17 Module installation procedure completed. ON STRT ENGINE STRT STOP 05 Connect the module to the computer with the programming cable (WEBLINK port). Flash the module with the latest firmware then flash the expansion pack. 11 Connect every connector to the module, as shown in STEP 2 of the WIRING DIGRM. 06 Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING DIGRM. 12 Connect every other connector to the module, as shown in STEP 3 of the WIRING DIGRM. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

9 PGE 9 OF 28 DOC.: # TYPE 1 - WIRING DIGRM - 1 OF 1 STEP 1 WRNING 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE STRT VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS IGNITION SWITCH BLCK 10 PIN MODULE STEP 2 CONNECT TO MODULE BLCK 10 PIN BLCK 20 PIN (VEHICLE HRNESS) RELY STEP 3 CONNECT TO MODULE BLUE 6 PIN BLUE 10 PIN BLCK 2 PIN (NOT USED) STEP 4 CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED) utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

10 E-Class Coupe PTS T GLK-Class Diesel PTS T GLK-Class PTS T SLK-Class MG PTS T SLK-Class PTS T utomotive Data Solutions Inc MODULE LOCTION POLRITY C-Class Coupe PTS T WIRE COLOR POSITION C-Class Sedan PTS T CONNECTOR TYPE CONNECTOR COLOR C-Class MG Sedan PTS T CONNECTOR NME YER WIRE DESCRIPTION MODEL MKE MERCEDES-BENZ C-Class MG Coupe PTS T COMPONENT LOCTOR PGE 10 OF 28 DOC.: # TYPE 2 - WIRE CHRT - 1 OF 1 Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

11 PGE 11 OF 28 DOC.: # TYPE 2 - WIRING DIGRM - 1 OF 2 STEP 1 WRNING 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE STRT VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS IGNITION SWITCH BLCK 10 PIN MODULE STEP 2 CONNECT TO MODULE BLCK 10 PIN BLCK 20 PIN (VEHICLE HRNESS) RELY STEP 3 CONNECT TO MODULE REFER TO WIRE CHRT BLUE 6 PIN REFER TO COMPONENT LOCTOR SEE MODULE PROGRMMING PROCEDURE - PTS TO IDENTIFY THE REQUIRED CN CONNECTOR. ONCE IDENTIFIED, DISCONNECT IT FROM THE CN JUNCTION CONNECTOR ND CONNECT IT TO C1. BLUE 10 PIN CN CONNECTORS CONNECT BLCK 2 PIN STEP 4 CN JUNCTION CONNECTOR CONNECT CNH CNL PINK/RED - CNH PINK/BLCK - CNL C1 IF THE REQUIRED CN CONNECTOR DOES NOT FIT IN C1: SEE NEXT PGE FOR INSTRUCTIONS CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED) utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

12 PGE 12 OF 28 DOC.: # TYPE 2 - WIRING DIGRM - 2 OF 2 INSTRUCTIONS TO CHNGE THE HOUSING OF CN WIRES (ONLY IF THE CN CONNECTOR DOES NOT FIT IN C1) 1- RELESE RETINING CLIP OF CN CONNECTOR. 2- RELESE LOCKING MECHNISM. REMOVE CN WIRES FROM HOUSING. - CNL - CNH 3- INSERT EMPTY HOUSING IN CN JUNCTION CONNECTOR (TO VOID LOSING IT). 4- INSERT CN WIRES IN PROVIDED HOUSING. CONNECT IT WITH C1 HRNESS, S SHOWN IN WIRING DIGRM. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

13 PGE 13 OF 28 DOC.: # TYPE 3 - WIRING DIGRM - 1 OF 1 WRNING STEP 1 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE STRT VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLCK 8 PIN B (VEHICLE HRNESS) MODULE STEP 2 IGNITION SWITCH BLCK 8 PIN CONNECT TO MODULE BLCK 20 PIN BLCK 10 PIN BLCK 10 PIN RELY STEP 3 CONNECT TO MODULE B BLCK 10 PIN (VEHICLE HRNESS) BLUE 6 PIN BLUE 10 PIN BLCK 2 PIN (NOT USED) STEP 4 CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED) utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

14 PGE 14 OF 28 DOC.: # E-Class Sedan Diesel PTS T E-Class Sedan PTS T E-Class Wagon PTS T GLK-Class Diesel PTS T GLK-Class PTS T utomotive Data Solutions Inc COMPONENT LOCTOR Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) WIRE COLOR MODULE LOCTION POLRITY E-Class MG Wagon PTS T POSITION MERCEDES-BENZ E-Class MG Sedan PTS T CONNECTOR TYPE CLS-Class Sedan PTS T CONNECTOR COLOR CONNECTOR NME YER CLS-Class MG Sedan PTS T WIRE DESCRIPTION MODEL MKE TYPE 4 - WIRE CHRT - 1 OF 1 Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) Brown/Red (DT) Brown (DT) DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

15 PGE 15 OF 28 DOC.: # TYPE 4 - WIRING DIGRM - 1 OF 2 STEP 1 WRNING 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE STRT VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLCK 8 PIN B (VEHICLE HRNESS) IGNITION SWITCH BLCK 8 PIN MODULE STEP 2 CONNECT TO MODULE BLCK 10 PIN BLCK 20 PIN BLCK 10 PIN B RELY STEP 3 BLCK 10 PIN CONNECT TO MODULE (VEHICLE HRNESS) BLUE 6 PIN BLUE 10 PIN REFER TO WIRE CHRT REFER TO COMPONENT LOCTOR SEE MODULE PROGRMMING PROCEDURE - PTS TO IDENTIFY THE REQUIRED CN CONNECTOR. ONCE IDENTIFIED, DISCONNECT IT FROM THE CN JUNCTION CONNECTOR ND CONNECT IT TO C1. CN CONNECTORS CONNECT CNH CNL PINK/RED - CNH PINK/BLCK - CNL BLCK 2 PIN STEP 4 CN JUNCTION CONNECTOR CONNECT C1 IF THE REQUIRED CN CONNECTOR DOES NOT FIT IN C1: SEE NEXT PGE FOR INSTRUCTIONS CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED) utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

16 PGE 16 OF 28 DOC.: # TYPE 4 - WIRING DIGRM - 2 OF 2 INSTRUCTIONS TO CHNGE THE HOUSING OF CN WIRES (ONLY IF THE CN CONNECTOR DOES NOT FIT IN C1) 1- RELESE RETINING CLIP OF CN CONNECTOR. 2- RELESE LOCKING MECHNISM. REMOVE CN WIRES FROM HOUSING. - CNL - CNH 3- INSERT EMPTY HOUSING IN CN JUNCTION CONNECTOR (TO VOID LOSING IT). 4- INSERT CN WIRES IN PROVIDED HOUSING. CONNECT IT WITH C1 HRNESS, S SHOWN IN WIRING DIGRM. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

17 MODULE PROGRMMING PROCEDURE - STD KEY - 1 OF 1 LED 1 is solid RED. Insert key into ignition. CC CC STRT Turn key to ON position. CC ON 03 Wait, LED 1 will turn solid GREEN then will turn. >> WRNING: If LED 1 flashes RED/GREEN, turn ignition to position. The vehicle is PTS. Follow appropriate PTS sections. CC ON STRT Module Programming Procedure completed. STRT 04 Turn key to position. Remove key from ignition. ON 06 PGE 17 OF 28 DOC.: # ON STRT STRT vehicle for 15 seconds. LED 1 will turn solid RED. Wait, LED 1 will turn solid GREEN then will turn. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

18 MODULE PROGRMMING PROCEDURE - PTS - 1 OF 1 >> One of the connectors of the CN junction connector controls the keyless authorization system (Keyless Go). The following procedure will allow the module to identify the required CN connector. >> If the parking lights do NOT flash, the required connector is NOT found. Reconnect it to the CN junction connector and repeat step 4 with another connector. >> Have the CN junction connector accessible. Identify every CN connector whose and wires match the colors listed in the WIRE CHRT. 04 Wait, LED 1 will turn solid GREEN then will turn. LED 1 is solid RED. Push start button to ON position. 05 STOP CC ON STRT ENGINE STRT STOP STOP CC ON STRT PGE 18 OF 28 DOC.: # STRT vehicle for 15 seconds. LED 1 will turn solid RED. ENGINE STRT STOP Wait, LED 1 will flash RED/GREEN Disconnect the first connector of the CN junction connector whose and wires match the colors listed in the WIRE CHRT. Wait 5 seconds. 07 Wait, LED 1 will turn solid GREEN then will turn. Push start button to position. STOP CC ON STRT ENGINE STRT STOP >> If the parking lights flash, the required connector is found. Connect it to the C1 connector as shown in the WIRING DIGRM and go to step 5. utomotive Data Solutions Inc Module Programming Procedure completed. DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

19 VLET MODE PROGRMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. CC ON STRT >> PGE 19 OF 28 DOC.: # To exit valet mode: repeat steps 1 to 4 then STRT vehicle for 15 seconds. Cycle ignition ON five times [5x /ON] rapidly. Parking Light will flash once [1x]. ENGINE STRT STOP Wait, Parking Light will flash twice [2x], pause for 1.5 second, then will flash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is. Turn ignition to position. CC ON STRT ENGINE STRT STOP 05 Valet Mode Programming Procedure completed. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

20 FTERMRKET REMOTE PROGRMMING - 1 OF 1 PGE 20 OF 28 DOC.: # FTERMRKET REMOTE PROGRMMING: NOTES I ll aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

21 PGE 21 OF 28 DOC.: # MODULE NVIGTION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO CCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 09 CC ON STRT TO CCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. 10 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO CCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 12 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MNDTORY: EXIT MODULE NVIGTION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. ENGINE STRT STOP 03 [X] utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

22 PGE 22 OF 28 DOC.: # [Y] OPTIONS [X] MENUS MODULE NVIGTION CHRT: NOTES I Default settings are listed in bold. ON ON ON ON ENBLE DISBLE* 45 SEC 90 SEC MIN MIN DISBLE N/ 03 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 03 MIN 05 MIN MIN MIN MIN MIN MIN MIN SEC 05 SEC SEC SEC SEC SEC SEC SEC N/ N/ N/ II Make sure the option is covered on the vehicle before attempting to change the setting [Z] SETTINGS MODULE NVIGTION CHRT - 1 OF 1 DISRM/UNLOCK BEFORE STRT RELOCK FTER STRT RELOCK FTER SHUTDOWN FORCE UNLOCK LL ON FIRST PRESS TKEOVER SECURE TKEOVER DELY FCTORY KEYLESS RS SEQUENCE CONFIGURTION Technical Support only MODULE RUN TIME WIT TO STRT DELY N/ *Vehicle will shutdown when a door is opened. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

23 [X] NUMBER OF PRKING LIGHT FLSHES DIGNOSTIC REMOTE STRTER ERROR CODES - 1 OF 1 I WRNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/ 11 N/ 12 N/ 13 N/ 14 N/ 15 N/ 16 CN communication failure during RS sequence. REMOTE STRTER ERROR CODES: NOTES utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN PGE 23 OF 28 DOC.: #

24 I II III DURING PROGRMMING DURING REMOTE STRT WITH IGNITION utomotive Data Solutions Inc. 26 DIGNOSTIC TEST MODULE LED 1 STTUS MODULE DIGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN dditional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. DIR-IDS(RS)-BZ3-[DS-BZ3]-EN PGE 24 OF 28 DOC.: #

25 MODULE RESET PROCEDURE - 1 OF 1 Disconnect all connectors from module except the BLCK 20-PIN connector. 07 Reconnect all connectors. Disconnect the BLCK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS ND HOLD the module s programming button while connecting the BLCK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELESE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN PGE 25 OF 28 DOC.: #

26 TKEOVER PROCEDURE - 1 OF 1 >> ll vehicle doors must be closed and locked prior to remote start sequence. 06 Press and release BRKE pedal. Time restriction. Complete steps 2 to 6 within 45 seconds. 07 Take over procedure completed. Unlock driver door. >> Failure to follow procedure will result in vehicle engine shutdown. 03 Open driver door and enter vehicle. 04 Close driver door. 05 CC ON STRT PGE 26 OF 28 DOC.: # Push start button once [1x] to ON position OR turn key to ON position. ENGINE STRT STOP utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

27 INSTLLTION CHECKLIST - 1 OF 2 PGE 27 OF 28 DOC.: # CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventillated area. Open driver door window for easy vehicle access. 03 Enter vehicle. Start the vehicle and let it run for 15 seconds. 04 Stop the vehicle and exit vehicle. 05 Close all vehicle doors, hood and trunk. 06 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. QUESTION 1: Does the vehicle remote start? YES: Go to step Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat step 6 and call technical support if the problem persists. QUESTION 2: Does the vehicle shut down? YES: Go to step Open hood. NO: Repeat step 7. If the problem persists, unlock the door using the OEM keyfob, enter vehicle and press brake pedal to shut down the vehicle and call technical support. QUESTION 3: Is the orange warning sticker "Sticker 1" placed under the hood? YES: Leave hood open and go to step Close all doors. 10 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9. QUESTION 4: Does the vehicle remote start? YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to question 5. NO: Go to step 11. QUESTION 5: Is the vehicle equipped with a factory hood switch? (Inside hood latch) YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. 11 Close hood. 12 Enter vehicle. Do NOT press brake pedal. 13 Close all doors. 14 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 15 Wait for the vehicle to start. 16 Press brake pedal. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. QUESTION 6: Does the vehicle shut down? YES: Go to step 17. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN

28 INSTLLTION CHECKLIST - 2 OF 2 PGE 28 OF 28 DOC.: # CHECKLIST 17 Exit vehicle. 18 Close all doors. 19 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 20 Wait for the vehicle to start. QUESTION 7: Is the vehicle equipped with a keyless authorization system (Keyless Go)? YES: Touch the exterior driver door handle to unlock door using the keyless authorization system (Keyless Go). Within 45 seconds, go to step Open driver door. NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 21. QUESTION 8: Does the vehicle shut down? YES: The module does NOT detect the unlock signal from the vehicle communication network. Call technical support. 22 Enter vehicle. NO: Go to step 22. QUESTION 9: Is the vehicle equipped with a keyless authorization system (Keyless Go)? YES: Push vehicle start button once [1x]. Go to step Press and release brake pedal. NO: Insert key into ignition and turn key to ON position. Go to step 23. QUESTION 10: Does the vehicle shut down? YES: Repeat this procedure from step 3. If the problem persists, call technical support. 24 Shut down the vehicle. 25 Installation checklist completed. NO: Go to step 24. utomotive Data Solutions Inc. 26 DIR-IDS(RS)-BZ3-[DS-BZ3]-EN