install guide FLC-CH(RS)-CH5-[FLRSCH5]-EN

Transcription

1 install guide Document number 89 Revision Date 00 firmware FLC-CH(RS)-CH-[FLRSCH] hardware FLRSCH accessories FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)

2 Page of VEHICLE LIST - OF FEATURES MODEL YEAR DATA IMMOBILIZER BYPASS X LOCK REMOTE START PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX STARTER CTRL DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS PARKING LIGHT CTRL* RAP SHUTDOWN CTRL WARNING 00 AT - 00 / 00C AT 0-07 or Aspen AT 07- PT Cruiser AT 0- or CHRYSLER INSTALL TYPE MAKE I Install Type requires a T-harness manufactured before 0//0 Install Type requires a T-harness manufactured after 0// Caliber (with start wire) AT 07 Caliber AT 07- Charger AT 0-07 or Durango AT 07- Magnum AT 0-07 or Nitro AT 07- Ram 00 AT Ram 00 AT Ram 00 AT Ram 00 chassis cab AT Ram 00 chassis cab AT 08- Ram 00 chassis cab AT 08- Commander AT 0-07 or Compass AT 07- Grand Cherokee AT 0-07 or Liberty AT 08- Patriot AT 07- Wrangler AT chassis cab AT 00 chassis cab AT * May require additional parts. RAM JEEP DODGE Sebring AT Avenger AT or

3 Page of BOX CONTENTS - OF BOX CONTENTS LED BLUE BLACK BLACK PIN T-HARNESS PROGRAMMING BUTTON LED A G F B E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK MS VS PIN VS MS AFTERMARKET HOOD SWITCH AND CABLE C D WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE

4 Page of COMPATIBLE ACCESSORIES - OF RF KIT (accessories sold separately) FLRF// RF KIT (NC) RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) CARLINK FLHRNTM TELEMATIC PORT (NC) TELEMATIC KIT (accessories sold separately) FLHRNTM PN 00 TELEMATIC PORT VEHICLE OBDII PORT (NC) OBDII CAR CONNECTION

5 Page of COMPONENT LOCATOR pin pin Pink/DkGreen /LtBlue C pin C pin Pink/LtBlue Brown/Tan C pin C pin Pink/DkGreen 07 Parking Light* /Blue C pin C pin Pink/DkGreen /LtBlue C pin C pin Pink/DkGreen /LtBlue C pin C pin Pink/Orange 8 Parking light relay, engine compartment. /LtBlue C pin C pin Pink/Orange /Blue /LtBlue 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* NAME LOCATION WIRE DESCRIPTION POLARITY Grand Cherokee C C 0- Parking Light* JEEP Commander WIRE COLOR Magnum POSITION Charger TYPE DODGE Caliber (with start wire) COLOR PT Cruiser 0-07 Parking Light* CHRYSLER 00/00C YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts.

6 Page of TYPE - WIRING DIAGRAM - OF VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C D A VS SKIM NOTE REMOVE THE WHITE/GREEN WIRE FROM THE BLUE AND RE-INSERT IT IN PIN (AS SHOWN) (SEE DETAILED INSTRUCTIONS ON THE NEXT PAGE) A CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS BEFORE: 0//0 A VS SKIM HARNESS MS 0 WHITE/RED 0 WHITE/GREEN B B NOTE PURPLE - STARTER OUTPUT WHITE/YELLOW - CONTROL OUTPUT STARTER - 0 CONTROL - 0 CONNECT THE WHITE/GREEN WIRE TO THE PINK WIRE AND CONNECT THE WHITE/RED WIRE TO THE RED WIRE (SEE DETAILED INSTRUCTIONS ON THE NEXT PAGE) A MS B WHITE/GREEN WHITE/RED WHITE/BROWN (NC) INSULATE WIRE 0 PINK 0 RED C BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT VEHICLE PARKING LIGHT CONNECTION GRAY/GREEN - HORN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT AMPS D V OR GRAY/WHITE - HOOD STATUS INPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT A 0 PARKING LIGHT OPTIONAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH

7 TYPE - WIRING DIAGRAM - OF NOTE Page 7 of NOTE STEP : -REMOVE THE WHITE/GREEN WIRE FROM THE BLUE CAREFULLY. -USE A UTILITY KNIFE TO PUSH GENTLY AGAINST THE LOCKING TAB. -DO NOT DAMAGE THE LOCKING TAB IN THE PROCESS. STEP : -IDENTIFY THE PINK (PIN 7) AND RED (PIN 9) WIRES FROM THE 0 PIN BLACK OF THE T HARNESS. -CAREFULLY STRIP THE PINK AND RED WIRES USING A WIRE STRIPPER. -DO NOT CUT THE WIRES IN THE PROCESS. WHITE/RED WHITE/GREEN STEP : -USING A UTILITY KNIFE, LIFT THE LOCKING TAB CAREFULLY FOR IT TO BE RE-USED. STEP : -CONNECT AND SOLDER THE WHITE/RED WIRE TO THE RED WIRE. -CONNECT AND SOLDER THE WHITE/GREEN WIRE TO THE PINK WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CONNECTIONS AND PRODUCT MALFUNCTION STEP : -INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE. STEP : -INSERT THE WIRE IN PIN OF THE, RIGHT NEXT TO WHERE IT USED TO BE. WHITE/RED WHITE/GREEN

8 Page 8 of COMPONENT LOCATOR - Parking Light* /LtBlue Pink/Red Violet Driver door module /Blue 07- Parking Light* /LtBlue 08- Parking Light* 07- Parking Light* /Blue 07- Parking Light Nitro NAME LOCATION WIRE DESCRIPTION Durango DODGE POLARITY Caliber WIRE COLOR DODGE Avenger POSITION Sebring TYPE Aspen COLOR CHRYSLER 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF /LtBlue Pink/Red Violet Driver door module /LtBlue 07- Parking Light* + White/Green /LtBlue 07- Parking Light * Requires additional parts.

9 Page 9 of WIRE COLOR POLARITY LOCATION COMPONENT LOCATOR White/Green /LtBlue White/Green /LtBlue White/Green /LtBlue White/Green /LtBlue 07- Parking Light* /Blue /Blue 08- Parking Light* /LtBlue Parking Light Parking Light Parking Light 08- Parking Light 08- Parking Light JEEP Compass POSITION Ram 00 TYPE Ram 00 COLOR Ram 00 NAME DODGE Ram 00 WIRE DESCRIPTION Ram 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF Liberty * Requires additional parts.

10 Page of TYPE POSITION WIRE COLOR POLARITY LOCATION COMPONENT LOCATOR 07- Parking Light* /Blue 07- Parking Light* + White/Orange Passenger kick pad /LtBlue Parking Light White/Green /LtBlue Parking Light White/Green /LtBlue RAM NAME COLOR Wrangler WIRE DESCRIPTION JEEP Patriot YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts.

11 Page of TYPE - WIRING DIAGRAM - OF VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT A VS SKIM E C D A VS SKIM HARNESS A MS A B MS PURPLE (NC) WHITE/YELLOW (NC) VEHICLE PARKING LIGHT CONNECTION CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WHITE/BROWN - PARKING LIGHT OUTPUT PARKING LIGHT OR CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT C AMPS V OR 0 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT GRAY/GREEN - HORN OUTPUT PARKING LIGHT A 0 PARKING LIGHT D OPTIONAL 0 GRAY/WHITE - HOOD STATUS INPUT DRIVER DOOR PIN HORN WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH

12 Page of COMPONENT LOCATOR pin pin Pink/DkGreen /LtBlue C pin C pin Pink/LtBlue Brown/Tan C pin C pin Pink/DkGreen 07 Parking Light* /Blue C pin C pin Pink/DkGreen /LtBlue C pin C pin Pink/DkGreen /LtBlue C pin C pin Pink/Orange 8 Parking light relay, engine compartment. /LtBlue C pin C pin Pink/Orange /Blue /LtBlue 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* NAME LOCATION WIRE DESCRIPTION POLARITY Grand Cherokee C C 0- Parking Light* JEEP Commander WIRE COLOR Magnum POSITION Charger TYPE DODGE Caliber (with start wire) COLOR PT Cruiser 0-07 Parking Light* CHRYSLER 00/00C YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts.

13 Page of TYPE - WIRING DIAGRAM - OF VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: A VS D SKIM 0//0 A A VS SKIM HARNESS MS B B PURPLE - STARTER OUTPUT WHITE/YELLOW - CONTROL OUTPUT STARTER - 0 CONTROL - 0 MS A B C VEHICLE PARKING LIGHT CONNECTION BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT WHITE/BROWN - PARKING LIGHT OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR GRAY/GREEN - HORN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT AMPS D V OR GRAY/WHITE - HOOD STATUS INPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT A 0 PARKING LIGHT OPTIONAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH

14 PROGRAMMING PROCEDURE - STD KEY - OF 0 Close driver door. 07 Turn key to OFF position. ACC ON START OFF 0 Re-open driver door to wake up data bus. 08 Remove key. ACC OFF 0 ON START Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to ON position. Wait, LED will turn solid GREEN for seconds. 0 LED will turn solid RED. Module Programming Procedure completed. 0 Within seconds, LED will flash GREEN rapidly. ACC ON START OFF 0 ACC OFF ON Page of START

15 VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within 7 seconds. 0 OFF ACC ON START >> Page of To exit valet mode: repeat steps to. Cycle ignition ON five times [x OFF/ON] rapidly. ENGINE START STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to OFF position. OFF ACC ON START ENGINE START STOP 0 Valet Mode Programming Procedure completed.

16 aftermarket Remote PRogRamming - OF Page of aftermarket Remote PRogRamming: notes I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.

17 Page 7 of NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously OFF ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X]

18 Page 8 of [Y] options [X] menus module navigation chart: notes I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 0 TAKEOVER [Z] settings module navigation chart - OF FACTORY KEYLESS RS SEQUENCE CONFIGURATION RUN TIME WAIT TO START DELAY 0 off 0 ON 0 off 0 ON 0 off 0 ON 0 off 0 ON 0 enable 0 DISABLE* 0 0 DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LocK + LocK + LocK 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 MIN 0 0 MIN 07 MIN 08 min 0 0 sec 0 0 SEC 0 08 SEC 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC *Vehicle will shutdown when a door is opened.

19 Page 9 of [Y] options [X] menus module navigation chart: notes 0 [Z] settings module navigation chart - OF HORN EVENT TRIGGER CONFIGURATION 0-07 Technical Support only 0 HORN CHIRPS WIDTH 0 DoubLe LocK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + START 0 DOUBLE LOCK + START 0 0 msec 0 msec 0 0 msec 0 *Vehicle will shutdown when a door is opened.

20 [X] number of PaRKing Light FLashes Diagnostic Remote starter error codes - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. CAN communication failure during RS sequence. Remote starter error codes: notes Page 0 of

21 I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Diagnostic test module LeD status module Diagnostics - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. Page of

22 RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Page of

23 TAKEOVER PROCEDURE - STD KEY - OF >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. ACC Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 0 >> Page of Turn key to ON position. ACC OFF ON START 0 Press and release BRAKE pedal. 0 Take over procedure completed.

24 installation checklist - OF Page of checklist WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Enter vehicle and close the doors. Question : Does the driver side sliding door open? Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question : Does the vehicle shut down? Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.