Automotive Data Solutions Inc. AVAILABLE FOR : OL-BLADE-AL. Rev. Date: February 1, 2019 Doc. No.: ##58522##

Transcription

1 Automotive Data Solutions Inc. OL-BLADE-AL(DL)-CH4-EN AVAILABLE FOR : OL-BLADE-AL Rev. Date: February, 209 Doc. No.: ##58522## CH4 PATENT NO. US 8,856,780 CA PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 209 TERMS OF USE: Automotive Data solutions Inc. ( ADs ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. prior to beginning installation of an ADs product in a vehicle, it is the Certified Technician s responsibility to review the most current product guide, Install guide and vehicle-specific notes available in Weblink. ADs is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. purchasers sole contractual remedy is refund of the purchase price of the ADs product(s). ADs reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users.

2 Page 2 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## INSTALL TYPE SELECTION FeATUReS MAKe MoDel YeAR VolKSWAGen RAM JeeP DoDGe CHRYSleR install TYPe DATA immobilizer BYPASS PRioRiTY UnloCK DooR lock DooR UnloCK ARM oem AlARM DiSARM oem AlARM TRUnK/HATCH ReleASe PoWeR liftgate PoWeR SliDinG DooR (l) PoWeR SliDinG DooR (R) DooR STATUS output TRUnK STATUS output RAP SHUTDoWn CTRl BRAKe PeDAl STATUS output e-brake output TACHoMeTeR output DATA/MUX ignition CTRl SeCURe TAKeoVeR PARKinG light CTRl or 2 Town & Country 08-6 or 2 Caravan 08-0 or 2 Challenger 08-4 or 2 Charger 08-0 or 2 Durango -3 or 2 Grand Caravan 08-9 or 2 Journey 09-0 or 2 Magnum 08 or 2 Ram or 2 Commander 08-0 or 2 Grand Cherokee 08-3 or 2 C/V 0-5 or or or or or or 2 Routan 09-2 or 2 Visit our website for advanced features.

3 Page 3 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## TYPE - WIRING DIAGRAM TYPE INSTALL IS NOT AVAILABLE FOR THIS HARDWARE

4 Page 4 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## TYPE 2 - WIRE CROSS REFERENCE CHART - OF 3 MAKe MoDel CHRYSleR YeAR DeSCRiPTion name TYPe PoSiTion DoDGe PolARiTY MoDUle location CoMPonenT locator Town & Country Town & Country Caravan 08-0 Challenger 08-4 Charger 08-0 Durango -3 Grand Caravan Grand Caravan CanH ~ ~ 2 pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White/Brown MUX At switch or driver kick panel ~ Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~ CanH ~ ~ 2 pin 5 White/Black (DATA) Ignition node ~ CanH ~ ~ 2 pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White/Brown MUX At switch or driver kick panel ~ CanH ~ ~ 2 pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~

5 Page 5 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## TYPE 2 - WIRE CROSS REFERENCE CHART - 2 OF 3 MAKe MoDel YeAR DoDGe DeSCRiPTion JeeP name TYPe PoSiTion RAM PolARiTY MoDUle location CoMPonenT locator Journey 09-0 Magnum 08 Ram Commander 08-0 Grand Cherokee Grand Cherokee 500 / 2500 / / C/V 0 Parking Light ~ ~ ~ ~ White/Purple (+) Passenger kick panel ~ CanH ~ ~ 2 pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ CanH ~ ~ 2 pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ CanH ~ ~ 2 pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver door ~ Parking Light ~ ~ ~ ~ N/A (-) At pin of relay 7 in IPM ~ CanH ~ Black 2 pin 5 White/LtGreen (DATA) Ignition node ~ CanL ~ Black 2 pin 6 White/LtBlue (DATA) Ignition node ~ Driver Door Pin ~ ~ 20 pin 5 Purple (-) Driver door module ~ Parking Light ~ ~ ~ N/A (-) At pin of relay 7 in IPM, under hood ~ CanH ~ Black 2 pin 5 White/LtBlue (DATA) Ignition node ~ CanL ~ Black 2 pin 6 White/Brown (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel, door harness ~ Parking Light ~ Black 0 pin White/LtGreen (MUX) Headlight switch ~ CanH ~ ~ 2 pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ CanH ~ ~ 2 pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~

6 Page 6 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## TYPE 2 - WIRE CROSS REFERENCE CHART - 3 OF 3 MAKe RAM MoDel YeAR DeSCRiPTion VolKSWAGen name TYPe PoSiTion PolARiTY MoDUle location CoMPonenT locator C/V -5 Routan 09-2 Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~

7 Page 7 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## TYPE 2 - WIRING DIAGRAM WARNING USE THIS WARNING OUTPUT ONLY ON USE VEHICLES THIS OUTPUT EQUIPPED ONLY WITH ON VEHICLES MUX PARKING EQUIPPED LIGHT WITH CONTROL MUX PARKING LIGHT CONTROL VEHICLE PARKING LIGHT (MUX) WIRE ONLY WHEN RAP SHUTDOWN IS REQUIRED VEHICLE DRIVER DOOR PIN (-) REMOTE STARTER 5 AMPS REARM (-) OUTPUT ST IGNITION (+) INPUT GLOW PLUG (+) INPUT DIESEL VEHICLES N400 DIODE WARNING REMOTE STARTER START OUTPUT MUST BE EXTENDED TO ITS MAXIMUM WHEN USING TACHLESS MODE (CRANK TIME: AT LEAST 2.5 SECONDS) OR USE TACH CONNECTION INSTEAD WHITE/RED WHITE PINK/BLACK NO WIRE BROWN/RED ORANGE/BLACK ORANGE BLUE/RED GREEN/RED *BLADE CONNECTOR EXACT PIN-OUT GRAY/RED WHITE/BLACK NO WIRE PINK BLACK BROWN/YELLOW ORANGE/WHITE NO WIRE BLUE/YELLOW YELLOW GRAY/YELLOW WHITE/BLACK - IGNITION (+) VEHICLE SIDE WHITE/RED - IGNITION (+) CONNECTOR SIDE WHITE YELLOW - MULTIPLEX PARKING LIGHT OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK - GLOW PLUG (+) OUTPUT PINK - IGNITION (+) INPUT VEHICLE SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GRAY/RED - IGNITION (+) INPUT FROM KEY GRAY/YELLOW (NC) BLACK (NC) IGNITION (+) CANH CANL

8 Page 8 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## CARTRIDGE INSTALLATION Slide cartridge into unit. Notice button under LED. 2 Ready for Module Programming Procedure. MODULE PROGRAMMING PROCEDURE Close driver door. 6 OFF Turn key to OFF position. Re-open driver door to wake up data bus. 7 Remove key. 2 Insert key into ignition. 8 UNLOCK Press UNLOCK on the OEM remote. 3 ON Turn key to ON position. If vehicle is not equipped with OEM remote, press module programming button. 4 LED will turn solid RED. 9 Wait, LED will turn solid BLUE for 2 seconds. 5 Within 5 seconds, LED will flash BLUE rapidly. 0 Module Programming Procedure completed.

9 Page 9 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## MODULE PROGRAMMING CARTRIDGE PROCEDURE INSTALLATION - PUSH TO START Slide Close cartridge driver door. into unit. Notice button under LED. 25 Æ x Ready DO NOT for PRESS Module BRAKE Programming PEDAL Procedure. Push start button once [x] to OFF position. 2 Æ x2 Re-open driver door to wake up data bus. DO NOT PRESS BRAKE PEDAL Push start button twice [2x] to ON position. 6 UNLOCK Press UNLOCK on the OEM remote. 3 LED will turn solid RED. 7 Wait, LED will turn solid BLUE for 2 seconds. 4 Within 5 seconds, LED will flash BLUE rapidly. 8 Module Programming Procedure completed.

10 Page 0 of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ A 980 l 990 Y 2000 A 200 B 98 M B 20 C 982 n C 202 D 983 P D 203 e 984 R e 204 F 985 S F 205 G 986 T G 206 H 987 V H 207 J 988 W J 208 K 989 X K 209 led STATUS Flashing RED DiAGnoSTiCS DURinG PRoGRAMMinG DURinG ReMoTe START WiTH ignition off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing BLUE Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid BLUE then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE DISCONNECT cartridge from remote starter. 3 LED will flash red. Immediately RELEASE programming button. 2 PRESS AND HOLD programming button while re-connecting cartridge to remote starter. 4 LED will turn solid red for 2 seconds. RESET COMPLETED. 5 RECONNECT all connectors. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.

11 Page of OL-BLADE-AL(DL)-CH4-EN Doc. No.: ##58522## WARNING: READ BEFORE REMOTE STARTING THE VEHICLE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - TO THE VEHICLE OWNER NOTE I All vehicle doors must be closed and locked prior to remote start sequence. 3 Insert key into ignition. È TIME RESTRICTIºN COMING UP! 4 ON Turn key to ON position. Wait 2 seconds for key validation. Press UNLOCK on after-market remote. 5 Press and release BRAKE pedal. 2 TIME RESTRICTIºN Within 45 SECONDS from previous step: Open vehicle door. Enter vehicle. 6! Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown. TAKE OVER PROCEDURE - PUSH TO START - TO THE VEHICLE OWNER NOTE I All vehicle doors must be closed and locked prior to remote start sequence. 3 Æ x2 DO NOT PRESS BRAKE PEDAL Push start button twice [2x] to ON position. È TIME RESTRICTIºN COMING UP! Press UNLOCK on after-market remote. 2 TIME RESTRICTIºN Within 45 SECONDS from previous step: Open vehicle door. Enter vehicle. 4 5! Wait 2 seconds for key validation. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown.