Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: September 14, 2017 Doc. No.: ##44374##

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI1-EN NI1 AVAILABLE FOR : ADS-AL CA Rev. Date: September 14, 2017 Doc. No.: ##44374## U.S. PATENT NO. 8,856,780 PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page 2 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## INSTALL TYPE SELECTION FeATUReS nissan infiniti MAKe MoDel YeAR install TYPe DATA immobilizer BYPASS SeCURe TAKeoVeR PRioRiTY UnloCK DooR lock DooR UnloCK ARM oem AlARM DiSARM oem AlARM TRUnK/HATCH ReleASe DooR STAT output HooD STAT output* TRUnK STAT output TACHoMeTeR output BRAKe STATUS output FX FX35 Intelli-key FX FX45 Intelli-key G Q Z Z 05 1 Murano Murano Murano Intelli-Key Titan 04 1 * Hood status is only available when a factory hood switch is present.

3 Page 3 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## COMPONENT LOCATOR M K J C H E F G D N

4 Page 4 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 1 - WIRE CROSS REFERENCE CHART - 1 OF 1 MAKe infiniti nissan MoDel YeAR nissan DeSCRiPTion name TYPe PoSiTion PolARiTY MoDUle location CoMPonenT locator FX FX Q Z 05 Murano Titan 04 CanL ~ ~ 16 pin 14 Red (DATA) OBDII connector ~ Security Light M3 ~ 40 pin 23 Green/Orange (-) In Driver Kick Panel C CanL ~ ~ 16 pin 14 Red (DATA) OBDII connector ~ Security Light M3 ~ 40 pin 23 Green/Orange (-) In Driver Kick Panel C CanL ~ ~ 16 pin 14 Pink (DATA) OBDII connector ~ Security Light M4 ~ 40 pin 65 Green (-) In Driver Kick Panel C CanL ~ ~ 16 pin 14 Pink (DATA) OBDII connector ~ Security Light M90 ~ 40 pin 23 Green/Orange (-) In Driver Kick Panel C CanL ~ ~ 16 pin 14 Yellow (DATA) OBDII connector ~ Security Light M34 ~ 40 pin 23 Green/Orange (-) Right Of Steering Column H CanH ~ ~ 16 pin 6 White (DATA) OBDII connector ~ CanL ~ ~ 16 pin 14 Red (DATA) OBDII connector ~ Security Light M18 ~ 40 pin 23 Green/Orange (-) Right Of Steering Column H

5 Page 5 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 1 - WIRING DIAGRAM - 1 OF 1 BCM SEE CHART FOR LOCATION EXCEPTION: INFINITI Q SEE CHART FOR DETAILS SECURITY LIGHT REMOTE STARTER TACH (AC) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL <- OPTIONAL <- OPTIONAL IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - CONNECTOR SIDE WHITE/RED - VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT* PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) CANH CANL *BRAKE STATUS IS NOT AVAILABLE ON TITAN STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER OBDII CONNECTOR UNDER DRIVER SIDE DASH SEE CHART FOR WIRE COLORS 16

6 Page 6 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 2 - WIRE CROSS REFERENCE CHART - 1 OF 1 MAKe MoDel infiniti YeAR DeSCRiPTion name TYPe PoSiTion nissan PolARiTY MoDUle location CoMPonenT locator FX35 Intelli-key FX45 Intelli-key Murano Intelli-key CanL ~ ~ 16 pin 14 Pink (DATA) OBDII connector ~ Intelli-key M34 ~ 40 pin 6 Green/Red (+) Right of steering column above gas pedal F Security Light M3 ~ 40 pin 23 Green/Orange (-) At BCM in passenger kick panel D CanL ~ ~ 16 pin 14 Pink (DATA) OBDII connector ~ Intelli-key M34 ~ 40 pin 6 Green/Red (+) Right of steering column above gas pedal F Security Light M3 ~ 40 pin 23 Green/Orange (-) At BCM in passenger kick panel D CanL ~ ~ 16 pin 14 Yellow (DATA) OBDII connector ~ Intelli-key M99 ~ 40 pin 6 Green (+) Behind glove box, near "A" Pillar N Security Light M35 ~ 40 pin 23 Green/Orange (-) Right of steering column H

7 Page 7 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 2 - WIRING DIAGRAM - 1 OF 1 REFER TO CHART FOR INTELLIGENT KEY UNIT LOCATION BCM SEE CHART FOR LOCATION SECURITY LIGHT ARE NOT PRESENT IN ALL VEHICLES. IF DURING YOUR REMOTE START SEQUENCE THE SECURITY LIGHT STAYS ON OR FLASHS, YOU MUST CUT OFF THE SECURITY LIGHT WIRE. REFER TO CHART FOR PIN LOCATION AND WIRE COLOR CONNECTOR SIDE VEHICLE SIDE REMOTE STARTER SECURITY LIGHT CONNECTOR SIDE TACH (AC) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT VEHICLE SIDE LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION INTERRUPT (+) INPUT WHITE/RED - IGNITION INTERRUPT (+) OUTPUT WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - SECURITY LIGHT INPUT BLUE/YELLOW - SECURITY LIGHT OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) CANH CANL STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH SEE CHART FOR WIRE COLORS

8 Page 8 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 3 - WIRE CROSS REFERENCE CHART - 1 OF 1 MAKe infiniti MoDel YeAR nissan DeSCRiPTion name TYPe PoSiTion PolARiTY MoDUle location CoMPonenT locator G35 Sedan G35 Coupe Z Murano CanH ~ ~ 16 pin 70 Blue (DATA) OBDII connector ~ CanL ~ ~ 16 pin 71 Red (DATA) OBDII connector ~ Security Light M3 ~ 24 pin 55 Green/Orange (-) In Driver Kick Panel C CanH ~ ~ 16 pin 70 Blue (DATA) OBDII connector ~ CanL ~ ~ 16 pin 71 Red (DATA) OBDII connector ~ Security Light M3 ~ 24 pin 55 Green/Orange (-) In Driver Kick Panel C CanH ~ ~ 16 pin 70 Blue (DATA) OBDII connector ~ CanL ~ ~ 16 pin 71 Red (DATA) OBDII connector ~ Security Light M3 ~ 24 pin 55 Green/Orange (-) In Driver Kick Panel C CanH ~ ~ 16 pin 70 Blue (DATA) OBDII connector ~ CanL ~ ~ 16 pin 71 Yellow (DATA) OBDII connector ~ Security Light M37 ~ 24 pin 55 Green/Orange (-) Right Of Steering Column H

9 Page 9 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## TYPE 3 - WIRING DIAGRAM - 1 OF 1 BCM SEE CHART FOR LOCATION CANL CANH REMOTE STARTER SECURITY LIGHT TACH (AC) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT IGNITION (+) OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - SECURITY LIGHT CONNECTOR SIDE WHITE/RED - SECURITY LIGHT VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER.

10 Page 10 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARDWIRE MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed.

11 XX-XX PATENT INSTALL GUIDE PAGE X-X Page 11 of 11 ADS-AL(DL)-NI1-EN Doc. No.: ##44374## IDENTIFY VEHICLE NOTICE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ A 1980 l 1990 Y 2000 A 2010 B 1981 M B 2011 C 1982 n C 2012 D 1983 P D 2013 e 1984 R e 2014 F 1985 S F 2015 G 1986 T G 2016 H 1987 V H 2017 J 1988 W J 2018 K 1989 X K 2019 led STATUS Flashing RED DiAGnoSTiCS DURinG PRoGRAMMinG DURinG ReMoTe START WiTH ignition off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTERS PATENT NO. 5,719,551; 6,011,460; 6,243,004; 6,249,216; 6,275,147; 6,297,731; 6,346,876; 6,392,534; 6,529,124; 6,696,927; 6,756,885; 6,756,886; 6,771,167; 6,812,829; 6,924,750; 7,010,402; 7,031,826; 7,046,126; 7,061,137; 7,068,153; 7,015,830; 7,205,679; 7,224,083; 7,369,936; 7,378,945; 7,489,233; 7,501,937; CANADIAN PATENT NO. 2,320,248; 2,415,023; 2,426,670; 2,414,991; 2,415,011; 2,415,027; 2,415,038; 2,415,041; 2,502,893; 2,451,490; 2,452,296; 2,451,487; EUROPEAN PATENT NO. 1,053,128; DE T2; U.S ; ; ; ; ; ; EP ; ; ;